Dave Airlie [Tue, 11 Sep 2018 01:52:54 +0000 (11:52 +1000)]
Merge tag 'drm-intel-next-2018-09-06-2' of git://anongit.freedesktop.org/drm/drm-intel into drm-next
Merge tag 'gvt-next-2018-09-04'
drm-intel-next-2018-09-06-1:
UAPI Changes:
- GGTT coherency GETPARAM: GGTT has turned out to be non-coherent for some
platforms, which we've failed to communicate to userspace so far. SNA was
modified to do extra flushing on non-coherent GGTT access, while Mesa will
mitigate by always requiring WC mapping (which is non-coherent anyway).
- Neuter Resource Streamer uAPI: There never really were users for the feature,
so neuter it while keeping the interface bits for compatibility. This is a
long due item from past.
Cross-subsystem Changes:
- Backmerge of branch drm-next-4.19 for DP_DPCD_REV_14 changes
Core Changes:
- None
Driver Changes:
- A load of Icelake (ICL) enabling patches (Paulo, Manasi)
- Enabled full PPGTT for IVB,VLV and HSW (Chris)
- Bugzilla #107113: Distribute DDB based on display resolutions (Mahesh)
- Bugzillas #100023,#107476,#94921: Support limited range DP displays (Jani)
- Bugzilla #107503: Increase LSPCON timeout (Fredrik)
- Avoid boosting GPU due to an occasional stall in interactive workloads (Chris)
- Apply GGTT coherency W/A only for affected systems instead of all (Chris)
- Fix for infinite link training loop for faulty USB-C MST hubs (Nathan)
- Keep KMS functional on Gen4 and earlier when GPU is wedged (Chris)
- Stop holding ppGTT reference from closed VMAs (Chris)
- Clear error registers after error capture (Lionel)
- Various Icelake fixes (Anusha, Jyoti, Ville, Tvrtko)
- Add missing Coffeelake (CFL) PCI IDs (Rodrigo)
- Flush execlists tasklet directly from reset-finish (Chris)
- Fix LPE audio runtime PM (Chris)
- Fix detection of out of range surface positions (GLK/CNL) (Ville)
- Remove wait-for-idle for PSR2 (Dhinakaran)
- Power down existing display hardware resources when display is disabled (Chris)
- Don't allow runtime power management if RC6 doesn't exist (Chris)
- Add debugging checks for runtime power management paths (Imre)
- Increase symmetry in display power init/fini paths (Imre)
- Isolate GVT specific macros from i915_reg.h (Lucas)
- Increase symmetry in power management enable/disable paths (Chris)
- Increase IP disable timeout to 100 ms to avoid DRM_ERROR (Imre)
- Fix memory leak from HDMI HDCP write function (Brian, Rodrigo)
- Reject Y/Yf tiling on interlaced modes (Ville)
- Use a cached mapping for the physical HWS on older gens (Chris)
- Force slow path of writing relocations to buffer if unable to write to userspace (Chris)
- Do a full device reset after being wedged (Chris)
- Keep forcewake counts over reset (in case of debugfs user) (Imre, Chris)
- Avoid false-positive errors from power wells during init (Imre)
- Reset engines forcibly in exchange of declaring whole device wedged (Mika)
- Reduce context HW ID lifetime in preparation for Icelake (Chris)
- Attempt to recover from module load failures (Chris)
- Keep select interrupts over a reset to avoid missing/losing them (Chris)
- GuC submission backend improvements (Jakub)
- Terminate context images with BB_END (Chris, Lionel)
- Make GCC evaluate GGTT view struct size assertions again (Ville)
- Add selftest to exercise suspend/hibernate code-paths for GEM (Chris)
- Use a full emulation of a user ppgtt context in selftests (Chris)
- Exercise resetting in the middle of a wait-on-fence in selftests (Chris)
- Fix coherency issues on selftests for Baytrail (Chris)
- Various other GEM fixes / self-test updates (Chris, Matt)
- GuC doorbell self-tests (Daniele)
- PSR mode control through debugfs for IGTs (Maarten)
- Degrade expected WM latency errors to DRM_DEBUG_KMS (Chris)
- Cope with errors better in MST link training (Dhinakaran)
- Fix WARN on KBL external displays (Azhar)
- Power well code cleanups (Imre)
- Fixes to PSR debugging (Dhinakaran)
- Make forcewake errors louder for easier catching in CI (WARNs) (Chris)
- Fortify tiling code against programmer errors (Chris)
- Bunch of fixes for CI exposed corner cases (multiple authors, mostly Chris)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180907105446.GA22860@jlahtine-desk.ger.corp.intel.com
Dave Airlie [Fri, 7 Sep 2018 01:03:24 +0000 (11:03 +1000)]
Merge tag 'omapdrm-4.20' of git://git./linux/kernel/git/tomba/linux into drm-next
omapdrm changes for v4.20
Big amount of changes from Laurent, reworking the driver towards the
model used by the other DRM drivers by reverting the direction of many
of the operations on the display pipeline. The aim of this work is to
allow omapdrm to use the common DRM panels and bridges. Not all of the
operations are dealt in these patches, so more work needs to be done.
The only change visible to the user should be the change in module
dependencies: e.g. earlier a panel module depended on an encoder module,
but now the encoder module depends on the panel module, which affects
the order in which to unload the modules.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/9bb1a01b-a632-ce0c-f249-7b5470967e3a@ti.com
Dave Airlie [Thu, 6 Sep 2018 23:34:04 +0000 (09:34 +1000)]
Merge tag 'drm-misc-next-2018-09-05' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 4.20:
UAPI Changes:
- Add userspace dma-buf device to turn memfd regions into dma-bufs (Gerd)
- Add per-plane blend mode property (Lowry)
- Change in drm_fourcc.h is documentation only (Brian)
Cross-subsystem Changes:
- None
Core Changes:
- Remove user logspam and useless lock in vma_offset_mgr destroy (Chris)
- Add get/verify_crc_source for improved crc source selection (Mahesh)
- Add __drm_atomic_helper_plane_reset to reduce copypasta (Alexandru)
Driver Changes:
- various: Replance ref/unref calls with drm_dev_get/put (Thomas)
- bridge: Add driver for TI SN65DSI86 chip (Sandeep)
- rockchip: Add PX30 support (Sandy)
- sun4i: Add support for R40 TCON (Jernej)
- vkms: Continued building out vkms, added gem support (Haneen)Driver Changes:
- various: fbdev: Wrap remove_conflicting_framebuffers with resource_len
accessors to remove a bunch of cargo-cult (Michał)
- rockchip: Add rgb output iface support + fixes (Sandy/Heiko)
- nouveau/amdgpu: Add cec-over-aux support (Hans)
- sun4i: Add support for Allwinner A64 (Jagan)
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Sandy Huang <hjc@rock-chips.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20180905202210.GA95199@art_vandelay
Joonas Lahtinen [Thu, 6 Sep 2018 13:54:43 +0000 (16:54 +0300)]
drm/i915: Update DRIVER_DATE to
20180906
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Joonas Lahtinen [Thu, 6 Sep 2018 13:51:50 +0000 (16:51 +0300)]
Merge tag 'gvt-next-2018-09-04' of https://github.com/intel/gvt-linux into drm-intel-next-queued
gvt-next-2018-09-04
- guest context shadow optimization for restore inhibit one (Yan)
- cmd parser optimization (Yan)
- W=1 warning fixes (Zhenyu)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
# Conflicts:
# drivers/gpu/drm/i915/gvt/reg.h
From: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180904030154.GG20737@zhen-hp.sh.intel.com
Joonas Lahtinen [Thu, 6 Sep 2018 13:45:54 +0000 (16:45 +0300)]
drm/i915: Update DRIVER_DATE to
20180906
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Joonas Lahtinen [Thu, 6 Sep 2018 12:14:18 +0000 (15:14 +0300)]
drm/i915: Update DRIVER_DATE to
20180906
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Chris Wilson [Wed, 5 Sep 2018 14:09:21 +0000 (15:09 +0100)]
drm/i915: Move final cleanup of drm_i915_private to i915_driver_destroy
Introduce a complementary function to i915_driver_create() to undo all
that is created.
Suggested-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180905140921.17467-2-chris@chris-wilson.co.uk
Chris Wilson [Wed, 5 Sep 2018 14:09:20 +0000 (15:09 +0100)]
drm/i915: Attach the pci match data to the device upon creation
Attach our device_info to the our i915 private on creation so that it is
always available for inspection.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180905140921.17467-1-chris@chris-wilson.co.uk
Heiko Stuebner [Wed, 5 Sep 2018 19:13:02 +0000 (21:13 +0200)]
drm/rockchip: rgb: add stub functions when rgb encoder is disabled
The newly added internal rgb encoder for Rockchip vops is missing
stubs for the case that the rgb output part is not enabled in the
kernel config. So add these.
Fixes: 1f0f01515172 (drm/rockchip: Add support for Rockchip Soc RGB output interface)
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[seanpaul fixed up checkpatch nits]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180905191302.26023-1-heiko@sntech.de
Imre Deak [Wed, 5 Sep 2018 10:00:05 +0000 (13:00 +0300)]
drm/i915/bdw: Increase IPS disable timeout to 100ms
During IPS disabling the current 42ms timeout value leads to occasional
timeouts, increase it to 100ms which seems to get rid of the problem.
References: https://bugs.freedesktop.org/show_bug.cgi?id=107494
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107562
Reported-by: Diego Viola <diego.viola@gmail.com>
Tested-by: Diego Viola <diego.viola@gmail.com>
Cc: Diego Viola <diego.viola@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180905100005.7663-1-imre.deak@intel.com
Haneen Mohammed [Mon, 3 Sep 2018 21:18:17 +0000 (00:18 +0300)]
drm/vkms: Fix race condition around accessing frame number
crtc_state is accessed by both vblank_handle() and the ordered
work_struct handle vkms_crc_work_handle() to retrieve and or update
the frame number for computed CRC.
Since work_struct can fail, add frame_end to account for missing frame
numbers.
Use (frame_[start/end]) for synchronization between hrtimer callback
and ordered work_struct handle.
This patch passes the following subtests from igt kms_pipe_crc_basic test:
bad-source, read-crc-pipe-A, read-crc-pipe-A-frame-sequence,
nonblocking-crc-pipe-A, nonblocking-crc-pipe-A-frame-sequence
Signed-off-by: Haneen Mohammed <hamohammed.sa@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180903211743.GA2773@haneenDRM
Chris Wilson [Tue, 4 Sep 2018 15:31:17 +0000 (16:31 +0100)]
drm/i915: Reduce context HW ID lifetime
Future gen reduce the number of bits we will have available to
differentiate between contexts, so reduce the lifetime of the ID
assignment from that of the context to its current active cycle (i.e.
only while it is pinned for use by the HW, will it have a constant ID).
This means that instead of a max of 2k allocated contexts (worst case
before fun with bit twiddling), we instead have a limit of 2k in flight
contexts (minus a few that have been pinned by the kernel or by perf).
To reduce the number of contexts id we require, we allocate a context id
on first and mark it as pinned for as long as the GEM context itself is,
that is we keep it pinned it while active on each engine. If we exhaust
our context id space, then we try to reclaim an id from an idle context.
In the extreme case where all context ids are pinned by active contexts,
we force the system to idle in order to recover ids.
We cannot reduce the scope of an HW-ID to an engine (allowing the same
gem_context to have different ids on each engine) as in the future we
will need to preassign an id before we know which engine the
context is being executed on.
v2: Improved commentary (Tvrtko) [I tried at least]
References: https://bugs.freedesktop.org/show_bug.cgi?id=107788
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180904153117.3907-1-chris@chris-wilson.co.uk
Heiko Stuebner [Thu, 30 Aug 2018 11:09:37 +0000 (13:09 +0200)]
drm/rockchip: vop: add rk3188 vop definitions
The rk3188 has 2 vops not using iommus which only output directly
to a rgb interface per vop. So all other output modes like hdmi
are provided by external brige chips.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Sandy Huang <hjc@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180830110937.1739-1-heiko@sntech.de
Sandy Huang [Thu, 30 Aug 2018 21:12:07 +0000 (23:12 +0200)]
drm/rockchip: vop: Add directly output rgb feature for px30
Add this feature bit indicate px30 vop can directly output
parallel or serial rgb data.
Signed-off-by: Sandy Huang <hjc@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180830211207.10480-4-heiko@sntech.de
Sandy Huang [Thu, 30 Aug 2018 21:12:06 +0000 (23:12 +0200)]
drm/rockchip: Add support for Rockchip Soc RGB output interface
Some Rockchip CRTCs, like rv1108 and px30, can directly output parallel
and serial RGB data to panel or conversion chip.
So add a feature-bit for vops to mark the ability for these direct
outputs and add an internal encoder in that case, that can attach to
bridge chipsor panels.
Changes in v7:
1. forget to delete rockchip_rgb_driver and delete it.
Changes in v6:
1. Update according to Heiko Stuebner' implemention, rgb output is
part of vop's feature, should not register as a independent
driver.
Changes in v5:
1. add SPDX-License-Identifier tag
Changes in v4:
1. add support px30;
Changes in v3:
1. update for rgb-mode move to panel node.
Changes in v2:
1. add error log when probe failed;
2. update name_to_output_mode() according to sean's suggest;
3. Fix uninitialized use of ret.
Signed-off-by: Sandy Huang <hjc@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180830211207.10480-3-heiko@sntech.de
Heiko Stuebner [Thu, 30 Aug 2018 21:12:05 +0000 (23:12 +0200)]
drm/rockchip: add function to check if endpoint is a subdriver
To be able to have both internal subdrivers and external bridge
drivers as output endpoints of vops, add a function to be able
to distinguish these.
changes in v8:
- improved function documentation
- better error handling
- put calls for node and pdev references
changes in v6:
- added function to check subdriver vs. bridge
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Sandy Huang <hjc@rock-chips.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180830211207.10480-2-heiko@sntech.de
Jernej Skrabec [Tue, 4 Sep 2018 04:40:52 +0000 (12:40 +0800)]
drm/sun4i: Add support for HDMI voltage regulator
Some boards have HDMI VCC pin connected to voltage regulator which may
not be turned on by default.
Add support for such boards by adding voltage regulator handling code to
HDMI driver.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
[Icenowy: change supply name to "hvcc"]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180904044053.15425-11-icenowy@aosc.io
Icenowy Zheng [Tue, 4 Sep 2018 04:40:51 +0000 (12:40 +0800)]
dt-bindings: sun4i-drm: add HDMI VCC supply property for sun8i-dw-hdmi
Allwiner SoCs with DesignWare HDMI controller all come with a "HVCC"
pin, which is the VCC of HDMI part.
Add a supply property to specify HVCC's regulator in the device tree.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180904044053.15425-10-icenowy@aosc.io
Jagan Teki [Tue, 4 Sep 2018 04:40:48 +0000 (12:40 +0800)]
dt-bindings: display: Add compatible for A64 HDMI
The HDMI controller on Allwinner A64 is similar on the one on
H3/H5/A83T (although the PHY is different with A83T).
Add A64 compatible and append A83T compatible as fallback.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Rob Herring <robh@kernel.org>
[Icenowy: refactor commit log]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180904044053.15425-7-icenowy@aosc.io
Jagan Teki [Tue, 4 Sep 2018 04:40:47 +0000 (12:40 +0800)]
drm/sun4i: Add support for A64 display engine
Display Engine(DE2) in Allwinner A64 has two mixers and tcons.
The routing for mixer0 is through tcon0 and connected to
LVDS/RGB/MIPI-DSI controller.
The routing for mixer1 is through tcon1 and connected to HDMI.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180904044053.15425-6-icenowy@aosc.io
Jagan Teki [Tue, 4 Sep 2018 04:40:46 +0000 (12:40 +0800)]
drm/sun4i: Add support for A64 mixers
Mixers in Allwinner have similar capabilities as others SoCs with DE2.
Add support for them.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[Icenowy: Add mixer1]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180904044053.15425-5-icenowy@aosc.io
Jagan Teki [Tue, 4 Sep 2018 04:40:45 +0000 (12:40 +0800)]
dt-bindings: display: Add compatible for A64 DE2 display pipeline
Allwinner A64 has a DE2 display pipeline. The TCONs are similar to the
ones in A83T, but the mixers are new (similar to the later R40 SoC).
This patch adds dt-binding documentation for A64 DE2 display pipeline.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Rob Herring <robh@kernel.org>
[Icenowy: Refactor and also cover TCON1]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180904044053.15425-4-icenowy@aosc.io
Gustavo A. R. Silva [Tue, 4 Sep 2018 19:07:49 +0000 (14:07 -0500)]
dma-buf/udmabuf: Fix NULL pointer dereference in udmabuf_create
There is a potential execution path in which pointer memfd is NULL when
passed as argument to fput(), hence there is a NULL pointer dereference
in fput().
Fix this by null checking *memfd* before calling fput().
Addresses-Coverity-ID:
1473174 ("Explicit null dereferenced")
Fixes: fbb0de795078 ("Add udmabuf misc device")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20180904190749.GA9308@embeddedor.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Gerd Hoffmann [Wed, 29 Aug 2018 12:20:26 +0000 (14:20 +0200)]
drm/virtio: add iommu support.
Use the dma mapping api and properly add iommu mappings for
objects, unless virtio is in iommu quirk mode.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20180829122026.27012-3-kraxel@redhat.com
Gerd Hoffmann [Wed, 29 Aug 2018 12:20:25 +0000 (14:20 +0200)]
drm/virtio: add virtio_gpu_object_detach() function
The new function balances virtio_gpu_object_attach().
Also make virtio_gpu_cmd_resource_inval_backing() static and switch
call sites to the new virtio_gpu_object_attach() function.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20180829122026.27012-2-kraxel@redhat.com
Gerd Hoffmann [Mon, 13 Aug 2018 15:28:55 +0000 (17:28 +0200)]
drm/virtio: track virtual output state
Track whenever an virtual output (crtc) is enabled or disabled.
On atomic updates check for both framebuffer being present and crtc
being enabled to figure whenever the output is active or not.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20180813152855.12863-1-kraxel@redhat.com
Peter Wu [Tue, 4 Sep 2018 20:27:47 +0000 (22:27 +0200)]
qxl: fix null-pointer crash during suspend
"crtc->helper_private" is not initialized by the QXL driver and thus the
"crtc_funcs->disable" call would crash (resulting in suspend failure).
Fix this by converting the suspend/resume functions to use the
drm_mode_config_helper_* helpers.
Tested system sleep with QEMU 3.0 using "echo mem > /sys/power/state".
During suspend the following message is visible from QEMU:
spice/server/display-channel.c:2425:display_channel_validate_surface: canvas address is 0x7fd05da68308 for 0 (and is NULL)
spice/server/display-channel.c:2426:display_channel_validate_surface: failed on 0
This seems to be triggered by QXL_IO_NOTIFY_CMD after
QXL_IO_DESTROY_PRIMARY_ASYNC, but aside from the warning things still
seem to work (tested with both the GTK and -spice options).
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Link: http://patchwork.freedesktop.org/patch/msgid/20180904202747.14968-1-peter@lekensteyn.nl
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Chris Wilson [Tue, 4 Sep 2018 16:29:02 +0000 (17:29 +0100)]
drm/i915: Be defensive and don't assume PSR has any commit to sync against
If the previous modeset commit has completed and is no longer part of
the crtc state, skip waiting for it.
Ville pointed out that, in fact, the commit is never removed after a
modeset so the only way we could see a NULL here should be if there was
never a commit attached. Nevertheless, we have the evidence it can be
NULL and it has been defended against elsewhere, for example commit
93313538c153 ("drm/i915: Pass idle crtc_state to intel_dp_sink_crc").
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107792
Fixes: c44301fce614 ("drm/i915: Allow control of PSR at runtime through debugfs, v6")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180904162902.2578-1-chris@chris-wilson.co.uk
Chris Wilson [Mon, 3 Sep 2018 09:31:55 +0000 (10:31 +0100)]
drm: Remove "protection" around drm_vma_offset_manager_destroy()
Using a spinlock to serialize the destroy function, within the destroy
function itself does not prevent the buggy driver from shooting
themselves in the foot - either way they still have a use-after-free
issue.
Reported-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Liviu Dudau <Liviu.Dudau@arm.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180903093155.3825-1-chris@chris-wilson.co.uk
Chris Wilson [Tue, 4 Sep 2018 11:57:19 +0000 (12:57 +0100)]
drm: Suppress user controlled spam for invalid drm_wait_vblank_ioctl
The ioctl arguments are under control of the user and as such we should
resist any temptation to flood the kernel logs with their errors.
Relegate the DRM_ERROR to a DRM_DEBUG so the user has to opt into
hearing of their own mistakes. (One day we will have a small ringbuffer
attached to the task, so that the concerned process can inspect its own
debug info for EINVAL without them being hitting syslog at all.)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180904115719.24525-1-chris@chris-wilson.co.uk
Chris Wilson [Tue, 4 Sep 2018 13:12:07 +0000 (14:12 +0100)]
drm/i915: Pull intel_uncore_arm_unclaimed_mmio_detection() under the spinlock
Elsewhere we manipulate uncore.unclaimed_mmio_check and
i915_param.mmio_debug under the irq lock (e.g. preserving the current
value across a user forcewake grab), but do not protect the manipulation
inside intel_uncore_arm_unclaimed_mmio_detection() from concurrent
access, even from itself. This is an issue as we do call
arm_unclaimed_mmio_detection from multiple threads without coordination.
Suggested-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intelcom>
Link: https://patchwork.freedesktop.org/patch/msgid/20180904131207.17563-1-chris@chris-wilson.co.uk
Tvrtko Ursulin [Mon, 3 Sep 2018 11:30:07 +0000 (12:30 +0100)]
drm/i915/icl: Fix context RPCS programming
There are two issues with the current RPCS programming for Icelake:
Expansion of the slice count bitfield has been missed, as well as the
required programming workaround for the subslice count bitfield size
limitation.
1)
Bitfield width for configuring the active slice count has grown so we need
to program the GEN8_R_PWR_CLK_STATE accordingly.
Current code was always requesting eight times the number of slices (due
writing to a bitfield starting three bits higher than it should). These
requests were luckily a) capped by the hardware to the available number of
slices, and b) we haven't yet exported the code to ask for reduced slice
configurations.
Due both of the above there was no impact from this incorrect programming
but we should still fix it.
2)
Due subslice count bitfield being only three bits wide and furthermore
capped to a maximum documented value of four, special programming
workaround is needed to enable more than four subslices.
With this programming driver has to consider the GT configuration as
2x4x8, while the hardware internally translates this to 1x8x8.
A limitation stemming from this is that either a subslice count between
one and four can be selected, or a subslice count equaling the total
number of subslices in all selected slices. In other words, odd subslice
counts greater than four are impossible, as are odd subslice counts
greater than a single slice subslice count.
This also had no impact in the current code base due breakage from 1)
always reqesting more than one slice.
While fixing this we also add some asserts to flag up any future bitfield
overflows.
v2:
* Use a local in all branches for clarity. (Lionel)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Bspec: 12247
Reported-by: tony.ye@intel.com
Suggested-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Cc: tony.ye@intel.com
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180903113007.2643-1-tvrtko.ursulin@linux.intel.com
Chris Wilson [Tue, 4 Sep 2018 06:38:02 +0000 (07:38 +0100)]
drm/i915/ringbuffer: Move double invalidate to after pd flush
Continuing the fun of trying to find exactly the delay that is
sufficient to ensure that the page directory is fully loaded between
context switches, move the extra flush added in commit
70b73f9ac113
("drm/i915/ringbuffer: Delay after invalidating gen6+ xcs") to just
after we flush the pd. Entirely based on the empirical data of running
failing tests in a loop until we survive a day (before the mtbf is 10-30
minutes).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107769
References:
70b73f9ac113 ("drm/i915/ringbuffer: Delay after invalidating gen6+ xcs")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180904063802.13880-1-chris@chris-wilson.co.uk
Chris Wilson [Tue, 4 Sep 2018 11:17:32 +0000 (12:17 +0100)]
drm/i915: Double check we didn't miss an unclaimed register access
Currently, if the user has enabled mmio-debug around each register
access, we presume that we have then checked them all. However, it is
still possible through omission (raw register access) or external
interaction that the unclaimed access was not highlighted.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180904111732.24266-1-chris@chris-wilson.co.uk
Ville Syrjälä [Mon, 3 Sep 2018 14:28:41 +0000 (17:28 +0300)]
drm/i915: Fix ICL+ HDMI clock readout
Copy the 38.4 vs. 19.2 MHz ref clock exception from the dpll
mgr into the clock readout function as well.
v2: Refactor the code into a common function
s/is_icl/gen11+/ (Rodrigo)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107722
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180903142841.14627-1-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Souptick Joarder [Tue, 4 Sep 2018 04:15:05 +0000 (09:45 +0530)]
Document/gpu: Use new vm_fault_t type
We have introduce new return type vm_fault_t for
fault handler. Update the document for the same.
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180904041505.GA2712@jordon-HP-15-Notebook-PC
Chris Wilson [Mon, 3 Sep 2018 15:23:04 +0000 (16:23 +0100)]
drm/i915: Use a cached mapping for the physical HWS
Older gen use a physical address for the hardware status page, for which
we use cache-coherent writes. As the writes are into the cpu cache, we use
a normal WB mapped page to read the HWS, used for our seqno tracking.
Anecdotally, I observed lost breadcrumbs writes into the HWS on i965gm,
which so far have not reoccurred with this patch. How reliable that
evidence is remains to be seen.
v2: Explicitly pass the expected physical address to the hw
v3: Also remember the wild writes we once had for HWS above 4G.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180903152304.31589-2-chris@chris-wilson.co.uk
Chris Wilson [Mon, 3 Sep 2018 15:23:03 +0000 (16:23 +0100)]
drm/i915: Combine cleanup_status_page()
Pull the physical status page cleanup into a common
cleanup_status_page() for caller simplicity.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180903152304.31589-1-chris@chris-wilson.co.uk
Chris Wilson [Mon, 3 Sep 2018 15:02:16 +0000 (16:02 +0100)]
drm/i915: Fix up FORCE_GPU_RELOC (debug) to flush CPU write domains
We currently assert that if the target is in a CPU write domain, we use
a CPU reloc path rather than the GPU reloc path. However, we have a debug
override to force the GPU path and that unfortunately hits the assert.
Include the async clflush under the debug option to ensure correct
behaviour even when debugging, and strict when not.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180903150216.19965-1-chris@chris-wilson.co.uk
Michał Mirosław [Sat, 1 Sep 2018 14:08:51 +0000 (16:08 +0200)]
drm/tegra: kick out simplefb
Kick out firmware fb when loading Tegra driver.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/b5c3972e5774d0d1f8887054a993bbc54e9dbe2a.1535810304.git.mirq-linux@rere.qmqm.pl
Michał Mirosław [Sat, 1 Sep 2018 14:08:51 +0000 (16:08 +0200)]
drm/sun4i: use simpler remove_conflicting_framebuffers(NULL)
Use remove_conflicting_framebuffers(NULL) instead of duplicating it.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/7d6d5bc4deac322b1351533c989cb3583e91be49.1535810304.git.mirq-linux@rere.qmqm.pl
Michał Mirosław [Sat, 1 Sep 2018 14:08:50 +0000 (16:08 +0200)]
drm/vc4: use simpler remove_conflicting_framebuffers(NULL)
Use remove_conflicting_framebuffers(NULL) instead of open-coding it.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Eric Anholt <eric@anholt.net>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/be7e6396e6e7159695a5bccc109c6ab49a51e0d8.1535810304.git.mirq-linux@rere.qmqm.pl
Michał Mirosław [Sat, 1 Sep 2018 14:08:49 +0000 (16:08 +0200)]
drm/virtio: use simpler remove_conflicting_pci_framebuffers()
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/25f89daf6217da98a52d41c4ad62a78272bb0cf6.1535810304.git.mirq-linux@rere.qmqm.pl
Michał Mirosław [Sat, 1 Sep 2018 14:08:48 +0000 (16:08 +0200)]
drm/mgag200: use simpler remove_conflicting_pci_framebuffers()
Remove duplicated call, while at it.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/90fc954f90de44157d6cc1c782147db6252c71e4.1535810304.git.mirq-linux@rere.qmqm.pl
Michał Mirosław [Sat, 1 Sep 2018 14:08:48 +0000 (16:08 +0200)]
drm/radeon: use simpler remove_conflicting_pci_framebuffers()
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/b61a2e458b6a2964039693d724cc75b4fcfb3ddb.1535810304.git.mirq-linux@rere.qmqm.pl
Michał Mirosław [Sat, 1 Sep 2018 14:08:46 +0000 (16:08 +0200)]
drm/bochs: use simpler remove_conflicting_pci_framebuffers()
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/b5fce8eba7472e5ba8e18c2624938be6c5aa6ebb.1535810304.git.mirq-linux@rere.qmqm.pl
Link: https://patchwork.freedesktop.org/patch/msgid/a9a4691b6eea789664edd6b85a85b7990953a222.1535810304.git.mirq-linux@rere.qmqm.pl
Michał Mirosław [Sat, 1 Sep 2018 14:08:47 +0000 (16:08 +0200)]
drm/cirrus: use simpler remove_conflicting_pci_framebuffers()
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/a9a4691b6eea789664edd6b85a85b7990953a222.1535810304.git.mirq-linux@rere.qmqm.pl
Michał Mirosław [Sat, 1 Sep 2018 14:08:46 +0000 (16:08 +0200)]
drm/amdgpu: use simpler remove_conflicting_pci_framebuffers()
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/fe59ab587ef4ef799b525fcc03d87800c5dc26d9.1535810304.git.mirq-linux@rere.qmqm.pl
Michał Mirosław [Sat, 1 Sep 2018 14:08:45 +0000 (16:08 +0200)]
fbdev: add remove_conflicting_pci_framebuffers()
Almost all PCI drivers using remove_conflicting_framebuffers() wrap it
with the same code.
v2: add kerneldoc for DRM helper
v3: propagate remove_conflicting_framebuffers() return value
+ move kerneldoc to where function is implemented
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/7db1c278276de420eb45a1b71d06b5eb6bbd49ef.1535810304.git.mirq-linux@rere.qmqm.pl
Michał Mirosław [Sat, 1 Sep 2018 14:08:45 +0000 (16:08 +0200)]
fbdev: add kerneldoc do remove_conflicting_framebuffers()
Document remove_conflicting_framebuffers() behaviour.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/283fef19815b991700b56119d8d5874a2a8da44e.1535810304.git.mirq-linux@rere.qmqm.pl
Michał Mirosław [Sat, 1 Sep 2018 14:08:44 +0000 (16:08 +0200)]
fbdev: allow apertures == NULL in remove_conflicting_framebuffers()
Interpret (otherwise-invalid) NULL apertures argument to mean all-memory
range. This will allow to remove several duplicates of this code
from drivers in following patches.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/b5fed539fe569035139c8594c23effd8c39f12ca.1535810304.git.mirq-linux@rere.qmqm.pl
Michał Mirosław [Sat, 1 Sep 2018 14:08:44 +0000 (16:08 +0200)]
fbdev: show fbdev number for debugging
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/ef584ecd8642e8b1a04f28d6d9c1864b5aa507bb.1535810304.git.mirq-linux@rere.qmqm.pl
Laurent Pinchart [Thu, 7 Jun 2018 16:55:04 +0000 (19:55 +0300)]
drm/omap: Don't call .set_timings() operation recursively
Instead of calling the .set_timings() operation recursively from the
display device backwards, iterate over the devices manually in the DRM
encoder code. This moves the complexity to a single central location and
simplifies the logic in omap_dss_device drivers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Fri, 8 Jun 2018 13:53:37 +0000 (16:53 +0300)]
drm/omap: Store CRTC timings in .set_timings() operation
The video timings are stored in the CRTC structure by the
omap_crtc_dss_set_timings() function, called by dss_mgr_set_timings()
from the .enable() operation of the internal encoders. This instead
belongs to the .set_timings() code paths. Move the
omap_crtc_dss_set_timings() calls accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Fri, 8 Jun 2018 12:59:31 +0000 (15:59 +0300)]
drm/omap: venc: Fixup video mode in .check_timings() operation
The VENC encoder modifies the requested video mode to match the NTSC or
PAL timings (or reject the video mode completely) in the .set_timings()
operation. This should be performed in the .check_timings() operation
instead. Move the fixup.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Fri, 8 Jun 2018 12:59:31 +0000 (15:59 +0300)]
drm/omap: sdi: Fixup video mode in .check_timings() operation
The SDI encoder modifies the pixel clock of the requested video mode to
take the limitations of the PLL into account in the .enable() operation.
This should be performed in the .check_timings() operation instead. Move
the fixup.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Fri, 8 Jun 2018 13:39:27 +0000 (16:39 +0300)]
drm/omap: hdmi: Constify video mode and related pointers
Constify many pointers to struct videomode, as well as pointers to
container structures, to ensure the video mode isn't modified after
the .check_timings() operation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Fri, 8 Jun 2018 12:59:31 +0000 (15:59 +0300)]
drm/omap: dsi: Fixup video mode in .set_config() operation
The DSI encoder modifies the passed videomode to take the requirements
of the internal DISPC-DSI bus into account in the .enable_video_output()
operation. This should be performed in the .check_timings() operation
instead. There is however no .check_timings() operation as the DSI
encoder uses a custom API, so move it to the closest match which is the
.set_config() operation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Fri, 8 Jun 2018 13:03:14 +0000 (16:03 +0300)]
drm/omap: dpi: Don't fixup video mode in dpi_set_mode()
The video mode is aleady fixed up by the .check_timings() operation,
there's no need to repeat that when enabling the DPI output.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Mon, 4 Jun 2018 22:57:09 +0000 (01:57 +0300)]
drm/omap: Call dispc timings check operation directly
Instead of call the dispc timings check function dispc_mgr_timings_ok()
from the internal encoders .check_timings() operation, expose it through
the dispc ops (after renaming it to check_timings) and call it directly
from omapdrm. This allows removal of now empty omap_dss_device
.check_timings() operations.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Thu, 7 Jun 2018 14:58:57 +0000 (17:58 +0300)]
drm/omap: Split mode fixup and mode set from encoder enable
The encoder enable operation currently performs mode fixup and mode
setting for all omap_dss_device instances in the display pipeline. There
are dedicated encoder operations for those operations (respectively
.atomic_check() and .mode_set()), but they are not used for this
purpose.
Move the mode fixup code to .atomic_check() and the mode set code
.mode_set() to better fit the KMS model. The bus flags fixup has to
happen at .mode_set() time as there is no place to store the bus flags
in the atomic state structures. This could be solved by extending one of
the state structures, but as the goal is to replace the fixup by direct
usage of bus flags through the driver, that would be pointless.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Thu, 7 Jun 2018 15:32:16 +0000 (18:32 +0300)]
drm/omap: Move bus flag hack to encoder implementation
The bus flags stored in omap_dss_device instances are used to fixup the
video mode before setting it, to honour constraints that can't be
expressed through drm_display_mode. The fixup occurs in the CRTC mode
set operation and the resulting video mode is stored internally in the
CRTC. It is then used next by omap_encoder_enable() to apply mode fixups
for the omap_dss_device instances in omap_encoder_update().
Move the hack to the omap_encoder_update() function right before
applying the omap_dss_device fixups, in order to group all fixups
together.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Wed, 6 Jun 2018 21:17:32 +0000 (00:17 +0300)]
drm/omap: panels: Don't modify fixed timings
Panels drivers store their timings in a device data structure field that
is initialized at probe time, either from hardcoded values or from
firmware-supplied values. Those timings are then reported through the
.get_timings() operation to construct the panel display mode.
The panel timings are further modified by the .set_timings() operation,
which is called with the timings retrieved by .get_timings(), and
mangled by .check_timings(). The latter potentially adjusts the pixel
clock only.
Conceptually, modifying the panel timings is wrong, as the timings are
an intrinsic property of the panel and should thus be fixed.
Furthermore, modifying them this way at runtime can result in display
modes reported to userspace varying between calls, which is also wrong.
There's no actual need to store the mangled pixel clock value in the
timings. Don't modify the panel timings in the .set_timings() operation,
just forward it to the previous device in the display pipeline.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Wed, 6 Jun 2018 15:04:26 +0000 (18:04 +0300)]
drm/omap: Remove .get_timings() operation from display connectors
The analog TV, DVI and HDMI connectors all report timing information
through the .get_timings() information.
For analog TV outputs the information is queried from the encoder, so
the operation is unused. Remove it.
For HDMI outputs the display pipeline provides EDID capability, so the
operation is unused as well. Remove it.
For DVI outputs the operation is also unused if the pipeline provides
EDID capability. Otherwise (when the DDC bus is not connected) we
shouldn't hardcode a single mode, but instead report no mode and let the
KMS core add default modes. This is achieved by removing the operation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Wed, 6 Jun 2018 14:49:37 +0000 (17:49 +0300)]
drm/omap: Query timing information from analog TV encoder
Timings for the TV output are currently reported by the analog TV
connector. This has the disadvantage of having to handle timing-related
operations in a connector omap_dss_device that has, at the hardware
level, no knowledge of any timing information.
Implement the .get_timings() operation in the venc driver, and get
timings from the first component in the pipeline that implements the
operatation. This switches the duty of reporting analog TV timings from
the connector to the encoder.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Tue, 5 Jun 2018 21:55:48 +0000 (00:55 +0300)]
drm/omap: Don't call .check_timings() operation recursively
The .check_timings() operation is called recursively from the display
device back to the output device. Most components just forward the
operation to the previous component in the chain, resulting in lots of
duplicated pass-through functions. To avoid that, iterate over the
components manually.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Wed, 6 Jun 2018 12:20:01 +0000 (15:20 +0300)]
drm/omap: Store bus flags in the omap_dss_device structure
Source components in the display pipeline need to configure their output
signals polarities and clock driving edge based on the requirements of
the sink component.
Those requirements are currently shared across the whole pipeline in the
flags of a videomode structure, instead of being local to each bus. This
both prevents multiple buses from having different configurations (when
the hardware supports it), and makes it difficult to move from videomode
to drm_display_mode as the latter doesn't contain bus polarities and
clock edge flags.
Add a bus_flags field to the omap_dss_device structure and move the
DISPLAY_FLAGS_DE_(LOW|HIGH), DISPLAY_FLAGS_PIXDATA_(POS|NEG)EDGE and
DISPLAY_FLAGS_SYNC_(POS|NEG)EDGE videomode flags to bus_flags in all
external encoders, connectors and panels. The videomode flags are still
used internally for internal encoders, this will be addressed in a
second step.
The related videomode flags in the default mode of the DVI connector can
simply be dropped, as they are always overridden by the TFP410 driver.
Note that this results in both the DISPLAY_FLAGS_SYNC_POSEDGE and
DISPLAY_FLAGS_SYNC_NEGEDGE flags being set, which is invalid, but only
the former is tested for when programming the DISPC, so the DVI
connector flags are effectively overridden by the TFP410 flags.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Wed, 6 Jun 2018 13:18:43 +0000 (16:18 +0300)]
drm/omap: Don't store video mode internally for external encoders
The omap_dss_device .set_timings() operation for external encoders
stores the video mode in the device data structure. That mode is then
never used again. Drop it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Tue, 5 Jun 2018 21:04:39 +0000 (00:04 +0300)]
drm/omap: Remove unneeded fallback for missing .check_timings()
The .check_timings() operation is present in all panels and connectors.
The fallback that uses .get_timings() in the absence of .check_timings()
is thus unneeded.
While it could be argued that the fallback implements a useful check
that should be extended to cover all fixed-resolution panels, the code
is currently unused and gets in the way of the ongoing refactoring.
Remove it, a similar feature can always be added later.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Mon, 4 Jun 2018 23:06:54 +0000 (02:06 +0300)]
drm/omap: Remove duplicate calls to .set_timings() operation
The omap_dss_device .set_timings() operations are called directly from
omap_encoder_update(), and indirectly from the omap_dss_device .enable()
operation. The latter is called from omap_encoder_enable(), right after
calling omap_encoder_update(). The .set_timings() operation it thus
called twice in a row. Fix it by removing the indirect call.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Mon, 4 Jun 2018 15:29:01 +0000 (18:29 +0300)]
drm/omap: Make the video_mode pointer to .set_timings() const
The .set_timings() operations of the omap_dss_device instances don't
need to modify the passed timings. Make the pointer const.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Sun, 19 Aug 2018 11:12:27 +0000 (14:12 +0300)]
drm/omap: encoder-tfp410: Don't fix timings in .set_timings() handler
Both the .check_timings() and .set_timings() handlers call
tfp410_fix_timings() to fix the timing's flags. As .check_timings() is
always called before .set_timings(), there's no need to fix the flags
twice. Remove the tfp410_fix_timings() call from .set_timings().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Mon, 4 Jun 2018 15:26:00 +0000 (18:26 +0300)]
drm/omap: dss: hdmi: Rename hdmi_display_(set|check)_timing() functions
The two functions implement the .set_timings() and .check_timings()
operations. Rename them to hdmi_disply_set_timings() and
hdmi_display_check_timings() respectively to match the operations names
and make searching the source code easier.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Tue, 5 Jun 2018 21:31:57 +0000 (00:31 +0300)]
drm/omap: Determine connector type directly in omap_connector.c
Instead of determining the connector type from the type of the display's
omap_dss_device and passing it to the omap_connector_init() function,
move the type determination code to omap_connector.c and remove the type
argument to the connector init function. This moves code to a more
natural location, making the driver easier to read.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Thu, 31 May 2018 20:14:43 +0000 (23:14 +0300)]
drm/omap: Pass both output and display omap_dss_device to connector init
The drm_connector implementation requires access to the omap_dss_device
corresponding to the display, which is passed to its initialization
function and stored internally. Refactoring of the timings operations
will require access to the output omap_dss_device. To prepare for that,
pass it to the connector initialization function and store it internally
as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Thu, 31 May 2018 19:56:59 +0000 (22:56 +0300)]
drm/omap: Don't call HDMI mode and infoframe operations recursively
The HDMI mode (.set_hdmi_mode()) and infoframe (.set_infoframe())
operations are called recursively from the display device back to the
HDMI encoder. This isn't required, as all components other than the HDMI
encoder just forward the operation to the previous component in the
chain. Call the operations directly on the HDMI encoder.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Thu, 31 May 2018 20:14:43 +0000 (23:14 +0300)]
drm/omap: Pass both output and display omap_dss_device to encoder init
The drm_encoder implementation requires access to the omap_dss_device
corresponding to the display, which is passed to its initialization
function and stored internally. Clean up of the HDMI mode and infoframe
handling will require access to the output omap_dss_device. To prepare
for that, pass it to the encoder initialization function and store it
internally as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Thu, 31 May 2018 20:04:30 +0000 (23:04 +0300)]
drm/omap: Get from CRTC to display device directly
The CRTC mode set implementation needs to access the omap_dss_device for
the pipeline display. To do so, it iterates over all pipelines to find
the one that contains an encoder corresponding to the CRTC, and request
the display device from the encoder. That's a very complicated dance
when the CRTC has a direct pipeline pointer already, and the pipeline
contains a pointer to the display device.
Replace the convoluted code with direct access.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Thu, 31 May 2018 19:09:14 +0000 (22:09 +0300)]
drm/omap: Don't call EDID read operation recursively
Instead of calling the EDID read operation (.read_edid()) recursively
from the display device back to the first device that provides EDID read
support, iterate over the devices manually in the DRM connector code.
This moves the complexity to a single central location and simplifies
the logic in omap_dss_device drivers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Wed, 30 May 2018 13:53:43 +0000 (16:53 +0300)]
drm/omap: Move HPD disconnection handling to omap_connector
On HDMI outputs, CEC support requires notification of HPD signal
deassertion. The HPD signal can be handled by various omap_dss_device
instances in the pipeline, and all of them forward HPD events to the
OMAP4 internal HDMI encoder.
Knowledge of the DSS internals need to be removed from the
omap_dss_device instances in order to migrate to drm_bridge. To do so,
move HPD handling for CEC to the omap_connector.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Wed, 30 May 2018 18:46:44 +0000 (21:46 +0300)]
drm/omap: Merge HPD enable operation with HPD callback registration
The omap_dss_device .enable_hpd() and .disable_hpd() are used to enable
and disable hot-plug detection at omapdrm probe and remove time. This is
required to avoid reporting hot-plug detection events before the DRM
infrastructure is ready to accept them, as that could result in crashes
or other malfunction.
Hot-plug event reporting is conditioned by both HPD being enabled
through the .enable_hpd() operation and by the HPD callback being
registered though the .register_hpd_cb() operation. We thus don't need a
separate enable operation if we can guarantee that callbacks won't be
registered too early.
HPD callbacks are registered at connector initialization time, which is
too early to start reporting HPD events. There's however nothing
blocking a move of callback registration to a later time when the
omapdrm driver calls the HPD enable operations. Do so, and remove the
HPD enable operation completely from omap_dss_device drivers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Wed, 30 May 2018 15:51:59 +0000 (18:51 +0300)]
drm/omap: Remove unneeded safety checks in the HPD operations
The HPD-related omap_dss_device operations are now only called when the
device supports HPD. There's no need to duplicate that check in the
omap_dss_device drivers. The .register_hpd_cb() operation can as a
result be turned into a void operation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Wed, 30 May 2018 15:49:48 +0000 (18:49 +0300)]
drm/omap: Don't call HPD registration operations recursively
Instead of calling the hot-plug detection callback registration
operations (.register_hpd_cb() and .unregister_hpd_cb()) recursively
from the display device back to the first device that provides hot plug
detection support, iterate over the devices manually in the DRM
connector code. This moves the complexity to a single central location
and simplifies the logic in omap_dss_device drivers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Mon, 28 May 2018 13:49:36 +0000 (16:49 +0300)]
drm/omap: Don't call .detect() operation recursively
Instead of calling the .detect() operation recursively from the display
device back to the first device that provides hot plug detection
support, iterate over the devices manually in the DRM connector
.detect() implementation. This moves the complexity to a single central
location and simplifies the logic in omap_dss_device drivers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Mon, 28 May 2018 13:03:13 +0000 (16:03 +0300)]
drm/omap: dss: Add device operations flags
When an omap_dss_device operation can be implemented in multiple places
in a chain of devices, it is important to find out which device to
address to perfom the operation. This is currently done by calling the
operation on the display device at the end of the chain, and recursively
delagating the operation to the previous device if it can't be performed
locally. The drawback of this approach is an increased complexity in
omap_dss_device drivers.
In order to simplify the drivers, we will switch from a recursive model
to an interative model, centralizing the complexity in a single
location. This requires knowing which operations an omap_dss_device
supports at runtime. We can already test which operations are
implemented by checking the operation pointer, but implemented
operations can require resources whose availability varies between
systems. For instance a hot-plug signal from a connector can be wired to
a GPIO or to a bridge chip.
Add operation flags that can be set in the omap_dss_device structure by
drivers to signal support for operations.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Fri, 1 Jun 2018 16:45:01 +0000 (19:45 +0300)]
drm/omap: Move most omap_dss_driver operations to omap_dss_device_ops
omap_dss_device instances have two ops structures, omap_dss_driver and
omap_dss_device_ops. The former is used for devices at the end of the
pipeline (a.k.a. display devices), and the latter for intermediate
devices.
Having two sets of operations isn't convenient as code that iterates
over omap_dss_device instances need to take them both into account.
There's currently a reasonably small amount of such code, but more will
be introduced to move the driver away from recursive operations. To
simplify current and future code, move all operations that are not
specific to the display device to the omap_dss_device_ops.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Mon, 28 May 2018 14:18:26 +0000 (17:18 +0300)]
drm/omap: panel-tpo-td043mtea1: Convert to the GPIO descriptors API
The GPIO descriptor API is favoured over the plain GPIO API for consumer
drivers. Using it simplifies the driver code.
As the descriptor API handles the active-low flag internally we need to
invert the polarity of all GPIO operations in the driver. Rename the
nreset_gpio field to reset_gpio to reflect that.
The reset GPIO is mandatory, so drop conditional tests through the
driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Mon, 28 May 2018 14:16:52 +0000 (17:16 +0300)]
drm/omap: panel-tpo-td028ttec1: Drop unneeded linux/gpio.h header
The driver doesn't use GPIOs and thus doesn't need to include the
linux/gpio.h header.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Mon, 28 May 2018 14:18:26 +0000 (17:18 +0300)]
drm/omap: panel-sony-acx565akm: Convert to the GPIO descriptors API
The GPIO descriptor API is favoured over the plain GPIO API for consumer
drivers. Using it simplifies the driver code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Mon, 28 May 2018 14:18:26 +0000 (17:18 +0300)]
drm/omap: panel-nec-nl8048hl11: Convert to the GPIO descriptors API
The GPIO descriptor API is favoured over the plain GPIO API for consumer
drivers. Using it simplifies the driver code.
The reset GPIO is mandatory, so drop conditional tests through the
driver. The qvga GPIO is unused, so drop it completely.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Mon, 28 May 2018 14:18:26 +0000 (17:18 +0300)]
drm/omap: encoder-tfp410: Convert to the GPIO descriptors API
The GPIO descriptor API is favoured over the plain GPIO API for consumer
drivers. Using it simplifies the driver code.
As the descriptor API handles the active-low flag internally we need to
invert the polarity of all GPIO operations in the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Mon, 28 May 2018 14:18:26 +0000 (17:18 +0300)]
drm/omap: connector-hdmi: Convert to the GPIO descriptors API
The GPIO descriptor API is favoured over the plain GPIO API for consumer
drivers. Using it simplifies the driver code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Sun, 27 May 2018 19:01:24 +0000 (22:01 +0300)]
drm/omap: Check omap_dss_device type based on the output_type field
Various functions that need to differentiate between omap_dss_device
instances corresponding to displays and to internal encoders use the
omap_dss_device.driver field, which is only set for display instances.
This gets in the way of the omap_dss_device operations refactoring.
Replace that with a check based on the output_type field which is set
for all omap_dss_device instances but displays.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Thu, 29 Mar 2018 11:51:04 +0000 (14:51 +0300)]
drm/omap: Remove unnecessary display output sanity checks
The omapdrm driver checks at suspend and resume time whether the
displays it operates on have their driver operations set. This check is
unneeded, as all display drivers set the driver operations field at
probe time and never touch it afterwards. This is furthermore proven by
the dereferencing of the driver field without checking it first in
several locations.
The omapdss driver performs a similar check at shutdown time. This is
unneeded as well, as the for_each_dss_display() macro it uses to iterate
over displays locates the displays by checking the driver field
internally.
As those checks are unnecessary, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Thu, 29 Mar 2018 11:08:12 +0000 (14:08 +0300)]
drm/omap: dss: Remove omap_dss_driver .[gs]et_mirror operations
The .get_mirror() and .set_mirror() omap_dss_driver operations are
implemented by the panel-tpo-td043mtea1 driver but are never used.
Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Thu, 29 Mar 2018 11:08:12 +0000 (14:08 +0300)]
drm/omap: dss: Remove unused omap_dss_driver operations
The .probe(), .remove(), .run_test(), .get_rotate() and .set_rotate()
omap_dss_driver operations are not used. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Tue, 6 Mar 2018 21:34:53 +0000 (23:34 +0200)]
drm/omap: dss: Remove the dss_mgr_(dis)connect() operations
The dss_mgr .connect() and .disconnect() are implemented as no-op in
omapdrm. The operations are unneeded, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Tue, 6 Mar 2018 22:28:18 +0000 (00:28 +0200)]
drm/omap: Set dispc_channel_connect from DSS output connect handlers
The omap_dss_device.dispc_channel_connect field is used by DSS outputs
to fail the .enable() operation if they're not connected. Set the field
directly from the (dis)connect handlers of the DSS outputs instead of
going through the CRTC dss_mgr operations.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Tue, 6 Mar 2018 22:22:10 +0000 (00:22 +0200)]
drm/omap: Remove supported output check in CRTC connect handler
The CRTC connect handler checks whether the DSS output supports the
DISPC channel assigned to it. As the channel is assigned to the output
by the output driver a failure there could only result from a driver
bug. All the output drivers have been verified and they are always
assigned a DISPC channel that is supported on the SoC they run on. The
check can thus be removed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
projects / openwrt / staging / blogic.git / log