ASoC: soc-pcm: crash in snd_soc_dapm_new_dai

Crash happens in snd_soc_dapm_new_dai() when substream->private_data
access is made and substream is NULL here. This is seen for DAIs where
only playback or capture stream is defined. This seems to be happening
for codec2codec DAI link.

Both playback and capture are 0 during soc_new_pcm(). This is probably
happening because cpu_dai and codec_dai are both validated either for
SNDRV_PCM_STREAM_PLAYBACK or SNDRV_PCM_STREAM_CAPTURE.

Shouldn't be playback = 1 when,
 - playback stream is available for codec_dai AND
 - capture stream is available for cpu_dai

and vice-versa for capture = 1?

Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/1579443563-12287-1-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: Intel: hda: Fix SKL dai count

With fourth pin added for iDisp for skl_dai, update SOF_SKL_DAI_NUM to
account for the change. Without this, dais from the bottom of the list
are skipped. In current state that's the case for 'Alt Analog CPU DAI'.

Fixes: ac42b142cd76 ("ASoC: SOF: Intel: hda: Add iDisp4 DAI")
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200113114054.9716-1-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: madera: Update handling of DAPM routes for mono muxed outputs

Correctly link both channels on the DAC if an output muxed between a
stereo and mono output. Without this one channel of the DAC may be
erroneously powered down whilst in mono mode.

Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200114161841.451-4-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: wm_adsp: Correct cache handling of new kernel control API

The recently added API that exposes firmware mixer controls to the
kernel is missing cache handling and all writes bypass the cache, this
obviously causes the cache to get out of sync with the hardware. Factor
out the cache handling into two new helper functions and call those from
both the normal ALSA control handlers and the new kernel API.

Fixes: eb65ccdb0836 ("ASoC: wm_adsp: Expose mixer control API")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200114161841.451-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: msm8916-wcd-digital: Reset RX interpolation path after use

For some reason, attempting to route audio through QDSP6 on MSM8916
causes the RX interpolation path to get "stuck" after playing audio
a few times. In this situation, the analog codec part is still working,
but the RX path in the digital codec stops working, so you only hear
the analog parts powering up. After a reboot everything works again.

So far I was not able to reproduce the problem when using lpass-cpu.

The downstream kernel driver avoids this by resetting the RX
interpolation path after use. In mainline we do something similar
for the TX decimator (LPASS_CDC_CLK_TX_RESET_B1_CTL), but the
interpolator reset (LPASS_CDC_CLK_RX_RESET_CTL) got lost when the
msm8916-wcd driver was split into analog and digital.

Fix this problem by adding the reset to
msm8916_wcd_digital_enable_interpolator().

Fixes: 150db8c5afa1 ("ASoC: codecs: Add msm8916-wcd digital codec")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200105102753.83108-1-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: msm8916-wcd-analog: Fix MIC BIAS Internal1

MIC BIAS Internal1 is broken at the moment because we always
enable the internal rbias resistor to the TX2 line (connected to
the headset microphone), rather than enabling the resistor connected
to TX1.

Move the RBIAS code to pm8916_wcd_analog_enable_micbias_int1/2()
to fix this.

Fixes: 585e881e5b9e ("ASoC: codecs: Add msm8916-wcd analog codec")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200111164006.43074-3-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: cros_ec_codec: Make the device acpi compatible

Add ACPI entry for cros_ec_codec.

Signed-off-by: Yu-Hsuan Hsu <yuhsuan@chromium.org>
Link: https://lore.kernel.org/r/20200112054900.236576-1-yuhsuan@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: sti: fix possible sleep-in-atomic

Change mutex and spinlock management to avoid sleep
in atomic issue.

Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20200113100400.30472-1-arnaud.pouliquen@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: msm8916-wcd-analog: Fix selected events for MIC BIAS External1

MIC BIAS External1 sets pm8916_wcd_analog_enable_micbias_ext1()
as event handler, which ends up in pm8916_wcd_analog_enable_micbias_ext().

But pm8916_wcd_analog_enable_micbias_ext() only handles the POST_PMU
event, which is not specified in the event flags for MIC BIAS External1.
This means that the code in the event handler is never actually run.

Set SND_SOC_DAPM_POST_PMU as the only event for the handler to fix this.

Fixes: 585e881e5b9e ("ASoC: codecs: Add msm8916-wcd analog codec")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200111164006.43074-2-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: hdac_hda: Fix error in driver removal after failed probe

In case system has multiple HDA codecs, and codec probe fails for
at least one but not all codecs, driver will end up cancelling
a non-initialized timer context upon driver removal.

Call trace of typical case:

[   60.593646] WARNING: CPU: 1 PID: 1147 at kernel/workqueue.c:3032
__flush_work+0x18b/0x1a0
[...]
[   60.593670]  __cancel_work_timer+0x11f/0x1a0
[   60.593673]  hdac_hda_dev_remove+0x25/0x30 [snd_soc_hdac_hda]
[   60.593674]  device_release_driver_internal+0xe0/0x1c0
[   60.593675]  bus_remove_device+0xd6/0x140
[   60.593677]  device_del+0x175/0x3e0
[   60.593679]  ? widget_tree_free.isra.7+0x90/0xb0 [snd_hda_core]
[   60.593680]  snd_hdac_device_unregister+0x34/0x50 [snd_hda_core]
[   60.593682]  snd_hdac_ext_bus_device_remove+0x2a/0x60 [snd_hda_ext_core]
[   60.593684]  hda_dsp_remove+0x26/0x100 [snd_sof_intel_hda_common]
[   60.593686]  snd_sof_device_remove+0x84/0xa0 [snd_sof]
[   60.593687]  sof_pci_remove+0x10/0x30 [snd_sof_pci]
[   60.593689]  pci_device_remove+0x36/0xb0

Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110235751.3404-9-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: Intel: fix HDA codec driver probe with multiple controllers

In case system has multiple HDA controllers, it can happen that
same HDA codec driver is used for codecs of multiple controllers.
In this case, SOF may fail to probe the HDA driver and SOF
initialization fails.

SOF HDA code currently relies that a call to request_module() will
also run device matching logic to attach driver to the codec instance.
However if driver for another HDA controller was already loaded and it
already loaded the HDA codec driver, this breaks current logic in SOF.
In this case the request_module() SOF does becomes a no-op and HDA
Codec driver is not attached to the codec instance sitting on the HDA
bus SOF is controlling. Typical scenario would be a system with both
external and internal GPUs, with driver of the external GPU loaded
first.

Fix this by adding similar logic as is used in legacy HDA driver
where an explicit device_attach() call is done after request_module().

Also add logic to propagate errors reported by device_attach() back
to caller. This also works in the case where drivers are not built
as modules.

Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110235751.3404-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: Intel: lower print level to dbg if we will reinit DSP

We will reinit DSP in a loop when it fails to initialize the first
time, as recommended. So, it is not an error before we finally give
up. And reorder the trace to make it more readable.

Signed-off-by: Bard liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110235751.3404-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: stm32: dfsdm: fix 16 bits record

In stm32_afsdm_pcm_cb function, the transfer size is provided in bytes.
However, samples are copied as 16 bits words from iio buffer.
Divide by two the transfer size, to copy the right number of samples.

Fixes: 1e7f6e1c69f0 ("ASoC: stm32: dfsdm: add 16 bits audio record support")
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Link: https://lore.kernel.org/r/20200110131131.3191-1-olivier.moysan@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: stm32: sai: fix possible circular locking

In current driver, locks can be taken as follows:
- Register access: take a lock on regmap config and then on clock.
- Master clock provider: take a lock on clock and then on regmap config.
This can lead to the circular locking summarized below.

Remove peripheral clock management through regmap framework, and manage
peripheral clock in driver instead. On register access, lock on clock
is taken first, which allows to avoid possible locking issue.

[ 6696.561513] ======================================================
[ 6696.567670] WARNING: possible circular locking dependency detected
[ 6696.573842] 4.19.49 #866 Not tainted
[ 6696.577397] ------------------------------------------------------
[ 6696.583566] pulseaudio/6439 is trying to acquire lock:
[ 6696.588697] 87b0a25b (enable_lock){..-.}, at: clk_enable_lock+0x64/0x128
[ 6696.595377]
[ 6696.595377] but task is already holding lock:
[ 6696.601197] d858f825 (stm32_sai_sub:1342:(sai->regmap_config)->lock){....}
...
[ 6696.812513]  Possible unsafe locking scenario:
[ 6696.812513]
[ 6696.818418]        CPU0                    CPU1
[ 6696.822935]        ----                    ----
[ 6696.827451]   lock(stm32_sai_sub:1342:(sai->regmap_config)->lock);
[ 6696.833618]                                lock(enable_lock);
[ 6696.839350]                                lock(stm32_sai_sub:1342:
                                              (sai->regmap_config)->lock);
[ 6696.848035]   lock(enable_lock);

Fixes: 03e78a242a15 ("ASoC: stm32: sai: add h7 support")
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Link: https://lore.kernel.org/r/20200109083254.478-1-olivier.moysan@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Fix NULL dereference at freeing

When an ASoC driver with pcm_destruct component ops is freed before
the PCM object instantiation (e.g. deferring the probe), it hits an
Oops at snd_soc_pcm_component_free() that calls the pcm_destruct ops
unconditionally.

Fix it by adding a NULL-check of rtd->pcm before calling callbacks.

Fixes: c64bfc906600 ("ASoC: soc-core: add new pcm_construct/pcm_destruct")
Reported-by: Matthias Brugger <matthias.bgg@gmail.com>
Tested-by: Ben Ho <ben.ho@mediatek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200107070956.15807-1-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: bytcht_es8316: Fix Irbis NB41 netbook quirk

When a quirk for the Irbis NB41 netbook was added, to override the defaults
for this device, I forgot to add/keep the BYT_CHT_ES8316_SSP0 part of the
defaults, completely breaking audio on this netbook.

This commit adds the BYT_CHT_ES8316_SSP0 flag to the Irbis NB41 netbook
quirk, making audio work again.

Cc: stable@vger.kernel.org
Cc: russianneuromancer@ya.ru
Fixes: aa2ba991c420 ("ASoC: Intel: bytcht_es8316: Add quirk for Irbis NB41 netbook")
Reported-and-tested-by: russianneuromancer@ya.ru
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200106113903.279394-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: rt5640: Fix NULL dereference on module unload

The rt5640->jack is NULL if jack is already disabled at the time of
driver's module unloading.

Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200106014707.11378-1-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: boards: Fix compile-testing RT1011/RT5682

On non-x86, the new driver results in a build failure:

sound/soc/intel/boards/cml_rt1011_rt5682.c:14:10: fatal error: asm/cpu_device_id.h: No such file or directory

The asm/cpu_device_id.h header is not actually needed here,
so don't include it.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200102135322.1841053-1-arnd@arndb.de
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: imx8: Fix dsp_box offset

dsp_box is used to keep DSP initiated messages. The value of dsp_offset
is set by the DSP with the first message, so we need a way to bootstrap
it in order to get the first message.

We do this by setting the correct default dsp_box offset which on i.MX8
is not zero.

Very interesting is why it has worked until now.

On i.MX8, DSP communicates with ARM core using a shared SDRAM memory
area. Actually, there are two shared areas:
* SDRAM0 - starting at 0x92400000, size 0x800000
* SDRAM1 - starting at 0x92C00000, size 0x800000

SDRAM0 keeps the data sections, starting with .rodata. By chance
fw_ready structure was placed at the beginning of .rodata.

dsp_box_base is defined as SDRAM0 + dsp_box_offset and it is placed
at the beginning of SDRAM1 (dsp_box_offset should be 0x800000). But
because it is zero initialized by default it points to SDRAM0 where
by chance the fw_ready was placed in the SOF firmware.

Anyhow, SOF commit 7466bee378dd811b ("clk: make freq arrays constant")
fw_ready is no longer at the beginning of SDRAM0 and everything shows
how lucky we were until now.

Fix this by properly setting the default dsp_box offset.

Fixes: 202acc565a1f050 ("ASoC: SOF: imx: Add i.MX8 HW support")
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191220170531.10423-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: topology: Prevent use-after-free in snd_soc_get_pcm_runtime()

remove_link() is currently calling snd_soc_remove_dai_link() after
it has already freed the memory for the link name. But this is later
read from snd_soc_get_pcm_runtime() causing a KASAN use-after-free
warning. Reorder the cleanups to fix this issue.

Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Dragos Tarcatu <dragos_tarcatu@mentor.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/20191204210447.11701-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: fsl_audmix: add missed pm_runtime_disable

The driver forgets to call pm_runtime_disable in probe failure
and remove.
Add the missed calls to fix it.

Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/20191203111303.12933-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: stm32: spdifrx: fix input pin state management

Changing input state in iec capture control is not safe,
as the pin state may be changed concurrently by ASoC
framework.
Remove pin state handling in iec capture control.

Note: This introduces a restriction on capture control,
when pin sleep state is defined in device tree. In this case
channel status can be captured only when an audio stream
capture is active.

Fixes: f68c2a682d44 ("ASoC: stm32: spdifrx: add power management")
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Link: https://lore.kernel.org/r/20191204154333.7152-4-olivier.moysan@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: stm32: spdifrx: fix race condition in irq handler

When snd_pcm_stop() is called in interrupt routine,
substream context may have already been released.
Add protection on substream context.

Fixes: 03e4d5d56fa5 ("ASoC: stm32: Add SPDIFRX support")
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Link: https://lore.kernel.org/r/20191204154333.7152-3-olivier.moysan@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: stm32: spdifrx: fix inconsistent lock state

In current spdifrx driver locks may be requested as follows:
- request lock on iec capture control, when starting synchronization.
- request lock in interrupt context, when spdifrx stop is called
from IRQ handler.

Take lock with IRQs disabled, to avoid the possible deadlock.

Lockdep report:
[   74.278059] ================================
[   74.282306] WARNING: inconsistent lock state
[   74.290120] --------------------------------
...
[   74.314373]        CPU0
[   74.314377]        ----
[   74.314381]   lock(&(&spdifrx->lock)->rlock);
[   74.314396]   <Interrupt>
[   74.314400]     lock(&(&spdifrx->lock)->rlock);

Fixes: 03e4d5d56fa5 ("ASoC: stm32: Add SPDIFRX support")
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Link: https://lore.kernel.org/r/20191204154333.7152-2-olivier.moysan@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: core: Fix access to uninitialized list heads

The error path of soc_new_pcm_runtime() invokes soc_free_pcm_runtime()
that may cause a few problems.  First off, it calls list_del() for
rtd->list that may not be initialized.  Similarly,
snd_soc_pcm_component_free() traverses over the component list that
may not be initialized, either.  Such access to the uninitialized list
head would lead to either a BUG_ON() or a memory corruption.

This patch fixes the access to uninitialized list heads by
initializing the list heads properly at the beginning before those
error paths.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191204151454.21643-1-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: Set dpcm_playback / dpcm_capture

When converting a normal link to a DPCM link we need
to set dpcm_playback / dpcm_capture otherwise playback/capture
streams will not be created resulting in errors like this:

[   36.039111]  sai1-wm8960-hifi: ASoC: no backend playback stream

Fixes: a655de808cbde ("ASoC: core: Allow topology to override machine driver FE DAI link config")
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20191204151333.26625-1-daniel.baluta@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: imx8: fix memory allocation failure check on priv->pd_dev

The memory allocation failure check for priv->pd_dev is incorrectly
pointer checking priv instead of priv->pd_dev. Fix this.

Addresses-Coverity: ("Logically dead code")
Fixes: 202acc565a1f ("ASoC: SOF: imx: Add i.MX8 HW support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191204124816.1415359-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: Intel: hda: hda-dai: fix oops on hda_link .hw_free

When the PCM_PARAM IPC fails while configuring the FE, the kernel
oopses in the HDaudio link DMA .hw_free operation. The root cause is a
NULL dma_data since the BE .hw_params was never called by the SOC
core.

This error can also happen if the HDaudio link DMA configuration IPC
fails in the BE .hw_params.

This patches makes sure the dma_data is properly saved in .hw_params,
and tested before being use in hw_free.

GitHub issue: https://github.com/thesofproject/linux/issues/1417

Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191218000518.5830-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: fix fault at driver unload after failed probe

If sof_machine_check() fails during driver probe, the IPC
state is not initialized and this will lead to a NULL
dereference at driver unload. Example log is as follows:

[ 1535.980630] sof-audio-pci 0000:00:1f.3: error: no matching ASoC machine driver found - aborting probe
[ 1535.980631] sof-audio-pci 0000:00:1f.3: error: failed to get machine info -19
[ 1535.980632] sof-audio-pci 0000:00:1f.3: error: sof_probe_work failed err: -19
[ 1550.798373] BUG: kernel NULL pointer dereference, address: 0000000000000008
...
[ 1550.798393] Call Trace:
[ 1550.798397]  snd_sof_ipc_free+0x15/0x30 [snd_sof]
[ 1550.798399]  snd_sof_device_remove+0x29/0xa0 [snd_sof]
[ 1550.798400]  sof_pci_remove+0x10/0x30 [snd_sof_pci]

Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191218000518.5830-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: wm8962: fix lambda value

According to user manual, it is required that FLL_LAMBDA > 0
in all cases (Integer and Franctional modes).

Fixes: 9a76f1ff6e29 ("ASoC: Add initial WM8962 CODEC driver")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/1576065442-19763-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: common: work-around incorrect ACPI HID for CML boards

On CML boards with the RT5682 headset codec and RT1011 speaker
amplifier, the platform firmware exposes three ACPI HIDs
(10EC5682, 10EC1011 and MX98357A). The last HID is a mistake in
DSDT tables, which causes the wrong machine driver to be loaded.

This patch changes the key used to identify boards and changes the
order of entries in the table to load the correct machine driver.
The order does matter and should not be modified to work-around this
firmware issue.

Signed-off-by: Amery Song <chao.song@intel.com>
Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191210004854.16845-9-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: Intel: split cht and byt debug window sizes

Turns out SSP 3-5 are only available on cht, to avoid dumping on
undefined registers let's split the definition.

Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191210004854.16845-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: loader: fix snd_sof_fw_parse_ext_data

An error occurs during parsing more than one ext_data from the mailbox, because
of invalid data offset handling. Fix by removing the incorrect duplicate
increment of the offset.

The return value is also reset in the switch case. This does not change the
behavior but improves readability - there is no longer a need to check what the
return value of get_ext_windows is.

Signed-off-by: Karol Trzcinski <karolx.trzcinski@linux.intel.com>
Signed-off-by: Bartosz Kokoszko <bartoszx.kokoszko@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191210004854.16845-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: loader: snd_sof_fw_parse_ext_data log warning on unknown header

Added warning log when found some unknown FW boot ext header,
to improve debuggability.

Signed-off-by: Karol Trzcinski <karolx.trzcinski@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191210004854.16845-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: simple-card: Don't create separate link when platform is present

In normal sound case all DAIs are detected as CPU-Codec.
simple_dai_link_of supports the presence of a platform but it counts
it as a CPU DAI resulting in the creation of an extra link.

Adding a platform property to a link description like:

simple-audio-card,dai-link {
cpu {
sound-dai = <&sai1>;
};
plat {
sound-dai = <&dsp>;
};
codec {
sound-dai = <&wm8960>;
}

will result in the creation of two links:
* sai1 <-> wm8960
* dsp  <-> wm8960

which is obviously not what we want. We just want one single link
with:
* sai1 <-> wm8960 (and platform set to dsp).

Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/20191209135353.17427-1-daniel.baluta@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: topology: Check return value for soc_tplg_pcm_create()

The return value of soc_tplg_pcm_create() is currently not checked
in soc_tplg_pcm_elems_load(). If an error is to occur there, the
topology ignores it and continues loading.

Fix that by checking the status and rejecting the topology on error.

Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Dragos Tarcatu <dragos_tarcatu@mentor.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191210003939.15752-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: topology: Check return value for snd_soc_add_dai_link()

snd_soc_add_dai_link() might fail. This situation occurs for
instance in a very specific use case where a PCM device and a
Back End DAI link are given identical names in the topology.
When this happens, soc_new_pcm_runtime() fails and then
snd_soc_add_dai_link() returns -ENOMEM when called from
soc_tplg_fe_link_create(). Because of that, the link will not
get added into the card list, so any attempt to remove it later
ends up in a panic.

Fix that by checking the return status and free the memory in case
of an error.

Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Dragos Tarcatu <dragos_tarcatu@mentor.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191210003939.15752-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: core: only flush inited work during free

There are many paths to soc_free_pcm_runtime which can both have and
have not yet inited the workqueue yet. When we flush the queue when we
have not yet inited the queue we cause warnings to be printed.

An example is soc_cleanup_card_resources which is called by
snd_soc_bind_card which has multiple failure points before and after
soc_link_init -> soc_new_pcm which is where the queue is inited.

Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20191128011358.39234-1-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: bytcr_rt5640: Update quirk for Teclast X89

When the Teclast X89 quirk was added we did not have jack-detection
support yet.

Note the over-current detection limit is set to 2mA instead of the usual
1.5mA because this tablet tends to give false-positive button-presses
when it is set to 1.5mA.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191203221442.2657-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: core: Init pcm runtime work early to avoid warnings

There are cases where we fail before we reach soc_new_pcm which would
init the workqueue. When we fail we attempt to flush the queue which
generates warnings from the workqueue subsystem when we have not inited
the queue. Solution is to use a proxy function to get around this issue.

Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20191203173007.46504-1-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: sst: Add missing include <linux/io.h>

Fix build error:

sound/soc/intel/atom/sst/sst.c: In function intel_sst_interrupt_mrfld:
sound/soc/intel/atom/sst/sst.c:93:5: error: implicit declaration of function memcpy_fromio;
 did you mean memcpy32_fromio? [-Werror=implicit-function-declaration]
     memcpy_fromio(msg->mailbox_data,
     ^~~~~~~~~~~~~
     memcpy32_fromio

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191128135853.8360-1-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: max98090: fix possible race conditions

max98090_interrupt() and max98090_pll_work() run in 2 different threads.
There are 2 possible races:

Note: M98090_REG_DEVICE_STATUS = 0x01.
Note: ULK == 0, PLL is locked; ULK == 1, PLL is unlocked.

max98090_interrupt      max98090_pll_work
----------------------------------------------
schedule max98090_pll_work
                        restart max98090 codec
receive ULK INT
                        assert ULK == 0
schedule max98090_pll_work (1).

In the case (1), the PLL is locked but max98090_interrupt unnecessarily
schedules another max98090_pll_work.

max98090_interrupt      max98090_pll_work      max98090 codec
----------------------------------------------------------------------
                                               ULK = 1
receive ULK INT
read 0x01
                                               ULK = 0 (clear on read)
schedule max98090_pll_work
                        restart max98090 codec
                                               ULK = 1
receive ULK INT
read 0x01
                                               ULK = 0 (clear on read)
                        read 0x01
                        assert ULK == 0 (2).

In the case (2), both max98090_interrupt and max98090_pll_work read
the same clear-on-read register.  max98090_pll_work would falsely
thought PLL is locked.
Note: the case (2) race is introduced by the previous commit ("ASoC:
max98090: exit workaround earlier if PLL is locked") to check the status
and exit the loop earlier in max98090_pll_work.

There are 2 possible solution options:
A. turn off ULK interrupt before scheduling max98090_pll_work; and turn
on again before exiting max98090_pll_work.
B. remove the second thread of execution.

Option A cannot fix the case (2) race because it still has 2 threads
access the same clear-on-read register simultaneously.  Although we
could suppose the register is volatile and read the status via I2C could
be much slower than the hardware raises the bits.

Option B introduces a maximum 10~12 msec penalty delay in the interrupt
handler.  However, it could only punish the jack detection by extra
10~12 msec.

Adopts option B which is the better solution overall.

Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20191122073114.219945-4-tzungbi@google.com
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: max98090: exit workaround earlier if PLL is locked

According to the datasheet, PLL lock time typically takes 2 msec and
at most takes 7 msec.

Check the lock status every 1 msec and exit the workaround if PLL is
locked.

Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20191122073114.219945-3-tzungbi@google.com
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: max98090: remove msleep in PLL unlocked workaround

It was observed Baytrail-based chromebooks could cause continuous PLL
unlocked when using playback stream and capture stream simultaneously.
Specifically, starting a capture stream after started a playback stream.
As a result, the audio data could corrupt or turn completely silent.

As the datasheet suggested, the maximum PLL lock time should be 7 msec.
The workaround resets the codec softly by toggling SHDN off and on if
PLL failed to lock for 10 msec.  Notably, there is no suggested hold
time for SHDN off.

On Baytrail-based chromebooks, it would easily happen continuous PLL
unlocked if there is a 10 msec delay between SHDN off and on.  Removes
the msleep().

Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20191122073114.219945-2-tzungbi@google.com
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: wm8904: fix automatic sysclk configuration

The simple-card tries to signal the codec to disable rate constraints,
see commit 2458adb8f92a ("SoC: simple-card-utils: set 0Hz to sysclk when
shutdown"). This wasn't handled by the codec, instead it would set the
FLL frequency to 0Hz which isn't working. Since we don't have any rate
constraints just ignore this request.

Fixes: 13409d27cb39 ("ASoC: wm8904: configure sysclk/FLL automatically")
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20191122232532.22258-1-michael@walle.cc
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: rt5677: Fix build error without CONFIG_SPI

If CONFIG_SPI is n, SND_SOC_RT5677_SPI also is n, building fails:

sound/soc/codecs/rt5677.o: In function `rt5677_irq':
rt5677.c:(.text+0x2dbf): undefined reference to `rt5677_spi_hotword_detected'
sound/soc/codecs/rt5677.o: In function `rt5677_dsp_work':
rt5677.c:(.text+0x3709): undefined reference to `rt5677_spi_write'

This adds stub helpers to fix this.

Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 461c623270e4 ("ASoC: rt5677: Load firmware via SPI using delayed work")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20191127082145.6100-1-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: topology: Fix unload for SAI/ESAI

Link unload now fails for ESAI/SAI DAIs with:

"error: invalid DAI type 6" because DAI type is not
properly handled.

Fix this by correctly handling cases where type is ESAI or SAI.

Fixes: a4eff5f86c9c5e7 ("ASoC: SOF: imx: Read ESAI parameters and send them to DSP")
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191126141606.21650-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: Intel: BYT: fix a copy/paste mistake in byt_dump()

The shim registers in BYT/CHT/BSW are 64bits based, correct the
copy/paste (from bdw.c where the shim registers are 32bits based) error
in byt_dump().

Fixes: 3a9e204d4e36 ("ASoC: SOF: Intel: Add context data to any IPC timeout")
Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191126141533.21601-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: AMD: Enable clk in startup intead of hw_params

Some usages only call startup and shutdown without setting hw_params
(e.g. arecord --dump-hw-params). If we don't enable clk in startup, it
will cause ref count error because the clk will be disabled in shutdown.
For this reason, we should move enabling clk from hw_params to startup.

In addition, the hw_params is fixed in this driver(48000 rate, 2
channels, S16_LE format) so we don't need to change the clk rate after
the hw_params is set.

Signed-off-by: Yu-Hsuan Hsu <yuhsuan@chromium.org>
Acked-by: Akshu Agrawal <akshu.agarawal@amd.com>
Link: https://lore.kernel.org/r/20191126075424.80668-1-yuhsuan@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: rt5682: fix i2c arbitration lost issue

This patch modified the HW initial setting to fix i2c arbitration lost issue.

Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20191125091940.11953-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: DMI long name - avoid to add board name if matches with product name

Current code:

  LENOVO-20QE000VMC-ThinkPadX1Carbon7th-20QE000VMC

With the patch:

  LENOVO-20QE000VMC-ThinkPadX1Carbon7th

Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20191120174435.30920-2-perex@perex.cz
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: improve the DMI long card code in asoc-core

Add append_dmi_string() function and make the code more readable.

Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191120174435.30920-1-perex@perex.cz
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Fix Kconfig indentation

Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^        /\t/' -i */Kconfig

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191120133252.6365-1-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-pcm: check symmetry before hw_params

This reverts commit 957ce0c6b8a1f (ASoC: soc-pcm: check symmetry after
hw_params).

That commit cause soc_pcm_params_symmetry can't take effect.
cpu_dai->rate, cpu_dai->channels and cpu_dai->sample_bits
are updated in the middle of soc_pcm_hw_params, so move
soc_pcm_params_symmetry to the end of soc_pcm_hw_params is
not a good solution, for judgement of symmetry in the function
is always true.

FIXME:
According to the comments of that commit, I think the case
described in the commit should disable symmetric_rates
in Back-End, rather than changing the position of
soc_pcm_params_symmetry.

Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1573555602-5403-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: pcm3168a: Update the RST gpio handling to align with documentation

The RST (reset-gpios) is low active so the driver must handle it
accordingly.

Add comments to explain clearly how the line is used.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191120131753.6831-3-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: dt-bindings: pcm3168a: Update the optional RST gpio for clarity

Use the standard name for the gpion in DT: reset-gpios

Document that the RST line is low active and update the example
accordingly.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191120131753.6831-2-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: core: add SND_SOC_BYTES_E

Add SND_SOC_BYTES_E to accept getter and putter.

Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20191120060844.224607-2-tzungbi@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: add control components management

This ASCII string can carry additional information about
soundcard components or configuration. Add the possibility
to set this string via the ASoC card.

Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20191119174933.25526-1-perex@perex.cz
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-pcm: remove soc_pcm_private_free()

soc-topology adds extra dai_link by using snd_soc_add_dai_link(),
and removes it by snd_soc_romove_dai_link().

This snd_soc_add/remove_dai_link() and/or its related
functions are unbalanced before, and now, these are balance-uped.
But, it finds the random operation issue, and it is reported by
Pierre-Louis.

When card was released, topology will call snd_soc_remove_dai_link()
via (A).

static void soc_cleanup_card_resources(struct snd_soc_card *card)
{
struct snd_soc_dai_link *link, *_link;

/* This should be called before snd_card_free() */
(A) soc_remove_link_components(card);

/* free the ALSA card at first; this syncs with pending operations */
if (card->snd_card) {
(B) snd_card_free(card->snd_card);
card->snd_card = NULL;
}

/* remove and free each DAI */
(X) soc_remove_link_dais(card);

for_each_card_links_safe(card, link, _link)
(C) snd_soc_remove_dai_link(card, link);

...
}

At (A), topology calls snd_soc_remove_dai_link().
Then topology rtd, and its related all data are freed.

Next, (B) is called, and then, pcm->private_free = soc_pcm_private_free()
is called.

static void soc_pcm_private_free(struct snd_pcm *pcm)
{
struct snd_soc_pcm_runtime *rtd = pcm->private_data;

/* need to sync the delayed work before releasing resources */
flush_delayed_work(&rtd->delayed_work);
snd_soc_pcm_component_free(rtd);
}

Here, it gets rtd via pcm->private_data.
But, topology related rtd are already freed at (A).
Normal sound card has no damage, becase it frees rtd at (C).

These are finalizing rtd related data.
Thus, these should be called when rtd was freed, not sound card
was freed. It is very natural and understandable.

In other words, pcm->private_free = soc_pcm_private_free()
is no longer needed.

Extra issue is that there is zero chance to call
soc_remove_dai() for topology related dai at (X).
Because (A) removes rtd connection from card too, and,
(X) is based on card connected rtd.

This means, (X) need to be called before (C) (= for normal sound)
and (A) (= for topology).

Now, I want to focus this patch which is the reason why
snd_card_free() = (B) is located there.

commit 4efda5f2130da033aeedc5b3205569893b910de2
("ASoC: Fix use-after-free at card unregistration")

Original snd_card_free() was called last of this function.
But moved to top to avoid use-after-free issue.
The issue was happen at soc_pcm_free() which was pcm->private_free,
today it is updated/renamed to soc_pcm_private_free().

In other words, (B) need to be called before (C) (= for normal sound)
and (A) (= for topology), because it needs (not yet freed) rtd.
But, (A) need to be called before (B),
because it needs card->snd_card pointer.

If we call flush_delayed_work() and snd_soc_pcm_component_free()
(= same as soc_pcm_private_free()) when rtd was freed (= (C), (A)),
there is no reason to call snd_card_free() at top of this function.
It can be called end of this function, again.

But, in such case, it will likely break unbind again, as Takashi-san
reported. When unbind is performed in a busy state, the code may
release still-in-use resources.
At least we need to call snd_card_disconnect_sync() at the first place.

The final code will be...

static void soc_cleanup_card_resources(struct snd_soc_card *card)
{
struct snd_soc_dai_link *link, *_link;

if (card->snd_card)
(Z) snd_card_disconnect_sync(card->snd_card);

(X) soc_remove_link_dais(card);
(A) soc_remove_link_components(card);

for_each_card_links_safe(card, link, _link)
(C) snd_soc_remove_dai_link(card, link);

...
if (card->snd_card) {
(B) snd_card_free(card->snd_card);
card->snd_card = NULL;
}
}

To avoid release still-in-use resources,
call snd_card_disconnect_sync() at (Z).

(X) is needed for both non-topology and topology.

    topology removes rtd via (A), and
non topology removes rtd via (C).

snd_card_free() is no longer related to use-after-free issue.
Thus, locating (B) is no problem.

Fixes: df95a16d2a9626 ("ASoC: soc-core: fix RIP warning on card removal")
Fixes: bc7a9091e5b927 ("ASoC: soc-core: add soc_unbind_dai_link()")
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/87o8xax88g.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-component: tidyup snd_soc_pcm_component_new/free() parameter

This patch uses rtd instead of pcm at snd_soc_pcm_component_new/free()
parameter.
This is prepare for dai_link remove bug fix on topology.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87pnhqx89j.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: wm_adsp: Expose mixer control API

Expose mixer control API for reading and writing controls from the kernel.
This API can be used by ALSA kernel drivers with ADSP support to
read and write firmware-defined memory regions.

Signed-off-by: Li Xu <li.xu@cirrus.com>
Signed-off-by: David Rhodes <david.rhodes@cirrus.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/1573847653-17094-2-git-send-email-david.rhodes@cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: tlv320aic31xx: configure output common-mode voltage

The tlv320aic31xx devices allow to adjust the output common-mode voltage
for best analog performance. The datasheet states that the common mode
voltage should be set to be <= AVDD/2.

This changes allows to configure the output common-mode voltage via a DT
property. If the property is absent the voltage is automatically chosen
as the highest voltage below/equal to AVDD/2.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20191118151207.28576-1-l.stach@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: Intel: Fix CFL and CML FW nocodec binary names.

The manifest information is different between CNL, CML and CFL platforms
hence we need to load different files.

Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191111222901.19892-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: pcm3168a: Add support for optional RST gpio handling

In case the RST line is connected to a GPIO line it needs to be pulled high
when the driver probes to be able to use the codec.

Add support also for cases when more than one codec is is controlled by the
same GPIO line by requesting the gpio with GPIOD_FLAGS_BIT_NONEXCLUSIVE.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191113124734.27984-3-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: pcm3168a: Document optional RST gpio

On boards where the RST line is not pulled up, but it is connected to a
GPIO line this property must present in order to be able to enable the
codec.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191113124734.27984-2-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: wm5100: add missed pm_runtime_disable

The driver forgets to call pm_runtime_disable in remove and
probe failure.
Add the calls to fix it.

Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20191118073707.28298-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: wm2200: add missed operations in remove and probe failure

This driver misses calls to pm_runtime_disable and regulator_bulk_disable
in remove and a call to free_irq in probe failure.
Add the calls to fix it.

Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191118073633.28237-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: qcom: q6asm-dai: add support to flac decoder

Qualcomm DSPs also support the flac decoder, so add support for FLAC
decoder and convert the snd_dec_flac params to qdsp format.

Co-developed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20191115102705.649976-4-vkoul@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: qcom: q6asm: add support to flac config

Qualcomm DSPs expect flac config to be set for flac decoders, so add the
API to program the flac config to the DSP

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20191115102705.649976-3-vkoul@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ALSA: compress: add flac decoder params

The current design of sending codec parameters assumes that decoders
will have parsers so they can parse the encoded stream for parameters
and configure the decoder.

But this assumption may not be universally true and we know some DSPs
which do not contain the parsers so additional parameters are required
to be passed.

So add these parameters starting with FLAC decoder. The size of
snd_codec_options is still 120 bytes after this change (due to this
being a union)

Co-developed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20191115102705.649976-2-vkoul@kernel.org
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: rt5677: rt5677_check_hotword() can be static

Fixes: 21c00e5df439 ("ASoC: rt5677: Enable jack detect while DSP is running")
Signed-off-by: kbuild test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20191114153304.n4pyix7qadu76tx4@4978f4969bb8
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: ti: davinci-mcasp: Use dma_request_chan() directly for channel request

dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191113095445.3211-3-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: dmaengine: Use dma_request_chan() directly for channel request

dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191113095445.3211-2-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: care card_probed at soc_cleanup_card_resources()

soc_cleanup_card_resources() will call card->remove(), but it should be
called if card->probe() or card->late_probe() are called.
snd_soc_bind_card() might be error before calling
card->probe() / card->late_probe().
In that time, card->remove() will be called.
This patch adds card_probed parameter to judge it.

Fixes: bfce78a559655 ("ASoC: soc-core: tidyup soc_init_dai_link()")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/87o8xg4ltr.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: move snd_soc_unbind_card() next to snd_soc_bind_card()

To makes code readable, this patch moves snd_soc_unbind_card() next
to snd_soc_bind_card().

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87pnhw4lu5.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: call snd_soc_dapm_shutdown() at soc_cleanup_card_resources()

It is easy to read code if it is cleanly using paired function/naming,
like start <-> stop, register <-> unregister, etc, etc.
But, current ALSA SoC code is very random, unbalance, not paired, etc.
It is easy to create bug at the such code, and it will be difficult to
debug.

snd_soc_bind_card() is calling snd_soc_dapm_init() for both
card and component.
Let's call paired snd_soc_dapm_shutdown() at paired
soc_cleanup_card_resources().

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87r22c4lub.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: tas2770: clean up an indentation issue

There is a block that is indented too deeply, remove
the extraneous tabs.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20191112190218.282337-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>

dt-bindings: vendor-prefixes: Add 'fsi[ab]' to the list of non-vendor prefixes

'fsia' and 'fsib' property prefixes were added as schema in commit
2f52475bac7e ("ASoC: fsi: switch to yaml base Documentation").
Unfortunately to do checks on actual vendor prefixes, we have to track
the handful of prefixes which are not vendors like 'fsia' and 'fsib'.

Fixes: 2f52475bac7e ASoC: fsi: switch to yaml base Documentation
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20191108153538.11970-1-robh@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: tidyup soc_probe_aux_devices()

snd_soc_bind_card() is calling many initialize functions
for each card / link / dai / aux etc, etc, etc...
When error happen, the message is indicated at snd_soc_bind_card(),
not at each functions.
But, only soc_probe_aux_devices() case is indicating error at functions,
not at snd_soc_bind_card().
It is not an issue, but unbalanced.

This patch moves error message to snd_soc_bind_card().
Also avoids deep-nested code.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87lfsthkw9.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: merge snd_soc_bind_card() and snd_soc_instantiate_card()

having both soc_bind_card() and snd_soc_instantiate_card() is
very confusable. Let's merge these.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87mud9hkwj.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: merge soc_remove_component() and soc_cleanup_component()

having both soc_remove_component() and soc_cleanup_component() is
very confusable. Let's merge these.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87o8xphkwt.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: merge snd_soc_remove_dai_link() and soc_unbind_dai_link()

We don't need to separete snd_soc_remove_dai_link() and
soc_unbind_dai_link() anymore. Let's merge these.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87pni5hkx1.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: merge snd_soc_add_dai_link() and soc_bind_dai_link()

We don't need to separete snd_soc_add_dai_link() and
soc_bind_dai_link() anymore. Let's merge these.

One note is that before this patch, it adds list (A)
eventhough if it had dai_link->ignore (1), or already bounded dai_link (2).
But I guess it is wrong. This patch also solve this issue.

/* BEFORE */
int soc_bind_dai_link(...)
{
...
(1) if (dai_link->ignore)
return 0;

(2) if (soc_is_dai_link_bound(...))
return 0;
...
}

int snd_soc_add_dai_link(...)
{
...
=> ret = soc_bind_dai_link(...);
=> if (ret < 0)
=> return ret;

(A) list_add_tail(&dai_link->list, &card->dai_link_list);
...
}

/* AFTER */

int snd_soc_add_dai_link(...)
{
...
(1) if (dai_link->ignore)
return 0;

(2) if (soc_is_dai_link_bound(...))
return 0;
...
(A) list_add_tail(&dai_link->list, &card->dai_link_list);
return 0;
}

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87r22lhkx8.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: merge snd_soc_unregister_dai() and soc_del_dai()

We don't need to separete snd_soc_unregister_dai() and
soc_del_dai() anymore. Let's merge these

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87sgn1hkxg.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: merge snd_soc_register_dai() and soc_add_dai()

We don't need to separete snd_soc_register_dai() and
soc_add_dai() anymore. Let's merge these

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87tv7hhkxm.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: soc-core: remove soc_is_dai_link_bound()

Because complex separeted "card pre-listed component" and
"topology added component" duplicated operation is now
becoming simple, we don't need to check already bound dai_link
which is not exist anymore.
This patch removes soc_is_dai_link_bound().

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87v9rxhkxw.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: topology: free kcontrol memory on error

The volume and bytes kcontrols are currently not freeing their
memory on initialization failures. When an error occurs, all the
widgets loaded so far are unloaded via sof_widget_unload().
But this only happens for the widgets that got successfully loaded.

Fix that by kfree()-ing the allocated memory on load error.

Fixes: 311ce4fe7637d ("ASoC: SOF: Add support for loading topologies")
Reviewed-by: Paul Olaru <paul.olaru@nxp.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Dragos Tarcatu <dragos_tarcatu@mentor.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191111222039.19651-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: PM: only suspend to D0I3 when needed

We should suspend audio to D3 by default, for the sake of power saving,
change the condition of D0I3 suspending here to that when there is
stream with suspend_ignored specified.

Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191111223343.19986-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: add helper to check if we should enter d0i3 suspend

Add helper to check if the DSP should be put in D0i3. This function
returns true if a stream has ignored the SUSPEND trigger to keep the
pipelines running in the DSP.

Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191111223343.19986-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: PM: add check before setting d0_substate

Add check before seeting d0_substate and return success if Audio DSP is
already in the target substate.

Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191111223343.19986-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: PM: add state machine to comments

Add Audio DSP state machine with comments. Note that the
'D0<-->runtime D0I3' part is not implemented yet.

Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191111223343.19986-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: SOF: Intel: hda: use fallback for firmware name

We have platforms such as CFL with no known I2S codec being used, and
the ACPI tables are currently empty, so fall-back to using the
firmware filename used in nocodec mode

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191111222901.19892-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: acpi-match: split CNL tables in three

Due to firmware manifest/signature differences, we have to use
different firmware names, so split CNL machine table in three (CNL,
CFL, CML).

The CFL table is currently empty since all known platforms use
HDaudio, but let's plan ahead.

Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191111222901.19892-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: wm8904: configure sysclk/FLL automatically

This adds a new mode WM8904_CLK_AUTO which automatically enables the FLL
if a frequency different than the MCLK is set.

These additions make the codec work with the simple-card driver in
general and especially in systems where the MCLK doesn't match the
required clock.

Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20191108203152.19098-1-michael@walle.cc
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Intel: kbl_rt5663_rt5514_max98927: Add dmic format constraint

On KBL platform, the microphone is attached to external codec(rt5514)
instead of PCH. However, TDM slot between PCH and codec is 16 bits only.
In order to avoid setting wrong format, we should add a constraint to
force to use 16 bits format forever.

Signed-off-by: Yu-Hsuan Hsu <yuhsuan@chromium.org>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190923162940.199580-1-yuhsuan@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Add DA7213 audio codec as selectable option

This commit adds the Dialog DA7213 audio codec as a selectable option
in the kernel config. Currently the driver can only be selected for
Intel Baytrail/Cherrytrail devices or if SND_SOC_ALL_CODECS is enabled.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20191108174843.11227-3-sebastian.reichel@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: rt5677: Wait for DSP to boot before loading firmware

Wait for hardware to startup. If we load before hardware is ready we
could end up corrupting the firmware.

Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20191106011335.223061-12-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: rt5677: Set ADC clock to use PLL and enable ASRC

Use the PLL to kept the correct 24M clock rate so frequency shift does
not occur when using the DSP VAD.

Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20191106011335.223061-11-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: bdw-rt5677: Turn on MCLK1 for DSP via DAPM

The RT5677 DSP needs the I2S MCLK1 to run its DSP. Add a dapm route to
SSP0 CODEC IN so the clock is turned on automatically when the DSP is
turned on.

Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20191106011335.223061-10-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: rt5677: Allow VAD to be shut on/off at all times

Due to limitations of the clocking configuration, we have no way of
scheduling our hibernation before the bdw dsp hibernates. This causes
issues when the system suspends with an open stream. We need userspace
to toggle the kcontrol before we are suspended so that any writes on
suspend are not lost and we don't corrupt the regmap.

Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20191106011335.223061-9-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>