John Keeping [Tue, 12 Sep 2017 09:24:40 +0000 (10:24 +0100)]
usb: gadget: ffs: handle I/O completion in-order
By submitting completed transfers to the system workqueue there is no
guarantee that completion events will be queued up in the correct order,
as in multi-processor systems there is a thread running for each
processor and the work items are not bound to a particular core.
This means that several completions are in the queue at the same time,
they may be processed in parallel and complete out of order, resulting
in data appearing corrupt when read by userspace.
Create a single-threaded workqueue for FunctionFS so that data completed
requests is passed to userspace in the order in which they complete.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Yoshihiro Shimoda [Wed, 27 Sep 2017 09:47:13 +0000 (18:47 +0900)]
usb: renesas_usbhs: fix usbhsf_fifo_clear() for RX direction
This patch fixes an issue that the usbhsf_fifo_clear() is possible
to cause 10 msec delay if the pipe is RX direction and empty because
the FRDY bit will never be set to 1 in such case.
Fixes: e8d548d54968 ("usb: renesas_usbhs: fifo became independent from pipe.")
Cc: <stable@vger.kernel.org> # v3.1+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Yoshihiro Shimoda [Wed, 27 Sep 2017 09:47:12 +0000 (18:47 +0900)]
usb: renesas_usbhs: fix the BCLR setting condition for non-DCP pipe
This patch fixes an issue that the driver sets the BCLR bit of
{C,Dn}FIFOCTR register to 1 even when it's non-DCP pipe and
the FRDY bit of {C,Dn}FIFOCTR register is set to 1.
Fixes: e8d548d54968 ("usb: renesas_usbhs: fifo became independent from pipe.")
Cc: <stable@vger.kernel.org> # v3.1+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Yoshihiro Shimoda [Mon, 25 Sep 2017 08:01:25 +0000 (17:01 +0900)]
usb: gadget: udc: renesas_usb3: Fix return value of usb3_write_pipe()
This patch fixes an issue that this driver cannot go status stage
in control read when the req.zero is set to 1 and the len in
usb3_write_pipe() is set to 0. Otherwise, if we use g_ncm driver,
usb enumeration takes long time (5 seconds or more).
Fixes: 746bfe63bba3 ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Yoshihiro Shimoda [Mon, 25 Sep 2017 08:01:24 +0000 (17:01 +0900)]
usb: gadget: udc: renesas_usb3: fix Pn_RAMMAP.Pn_MPKT value
According to the datasheet of R-Car Gen3, the Pn_RAMMAP.Pn_MPKT should
be set to one of 8, 16, 32, 64, 512 and 1024. Otherwise, when a gadget
driver uses an interrupt endpoint, unexpected behavior happens. So,
this patch fixes it.
Fixes: 746bfe63bba3 ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Yoshihiro Shimoda [Mon, 25 Sep 2017 08:01:23 +0000 (17:01 +0900)]
usb: gadget: udc: renesas_usb3: fix for no-data control transfer
When bRequestType & USB_DIR_IN is false and req.length is 0 in control
transfer, since it means non-data, this driver should not set the mode
as control write. So, this patch fixes it.
Fixes: 746bfe63bba3 ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Alan Stern [Tue, 26 Sep 2017 19:15:49 +0000 (15:15 -0400)]
USB: dummy-hcd: Fix erroneous synchronization change
A recent change to the synchronization in dummy-hcd was incorrect.
The issue was that dummy_udc_stop() contained no locking and therefore
could race with various gadget driver callbacks, and the fix was to
add locking and issue the callbacks with the private spinlock held.
UDC drivers aren't supposed to do this. Gadget driver callback
routines are allowed to invoke functions in the UDC driver, and these
functions will generally try to acquire the private spinlock. This
would deadlock the driver.
The correct solution is to drop the spinlock before issuing callbacks,
and avoid races by emulating the synchronize_irq() call that all real
UDC drivers must perform in their ->udc_stop() routines after
disabling interrupts. This involves adding a flag to dummy-hcd's
private structure to keep track of whether interrupts are supposed to
be enabled, and adding a counter to keep track of ongoing callbacks so
that dummy_udc_stop() can wait for them all to finish.
A real UDC driver won't receive disconnect, reset, suspend, resume, or
setup events once it has disabled interrupts. dummy-hcd will receive
them but won't try to issue any gadget driver callbacks, which should
be just as good.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: f16443a034c7 ("USB: gadgetfs, dummy-hcd, net2280: fix locking for callbacks")
CC: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Alan Stern [Tue, 26 Sep 2017 19:15:40 +0000 (15:15 -0400)]
USB: dummy-hcd: fix infinite-loop resubmission bug
The dummy-hcd HCD/UDC emulator tries not to do too much work during
each timer interrupt. But it doesn't try very hard; currently all
it does is limit the total amount of bulk data transferred. Other
transfer types aren't limited, and URBs that transfer no data (because
of an error, perhaps) don't count toward the limit, even though on a
real USB bus they would consume at least a minimum overhead.
This means it's possible to get the driver stuck in an infinite loop,
for example, if the host class driver resubmits an URB every time it
completes (which is common for interrupt URBs). Each time the URB is
resubmitted it gets added to the end of the pending-URBs list, and
dummy-hcd doesn't stop until that list is empty. Andrey Konovalov was
able to trigger this failure mode using the syzkaller fuzzer.
This patch fixes the infinite-loop problem by restricting the URBs
handled during each timer interrupt to those that were already on the
pending list when the interrupt routine started. Newly added URBs
won't be processed until the next timer interrupt. The problem of
properly accounting for non-bulk bandwidth (as well as packet and
transaction overhead) is not addressed here.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Alan Stern [Tue, 26 Sep 2017 19:15:22 +0000 (15:15 -0400)]
USB: dummy-hcd: fix connection failures (wrong speed)
The dummy-hcd UDC driver is not careful about the way it handles
connection speeds. It ignores the module parameter that is supposed
to govern the maximum connection speed and it doesn't set the HCD
flags properly for the case where it ends up running at full speed.
The result is that in many cases, gadget enumeration over dummy-hcd
fails because the bMaxPacketSize byte in the device descriptor is set
incorrectly. For example, the default settings call for a high-speed
connection, but the maxpacket value for ep0 ends up being set for a
Super-Speed connection.
This patch fixes the problem by initializing the gadget's max_speed
and the HCD flags correctly.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Bjørn Mork [Fri, 22 Sep 2017 20:18:18 +0000 (22:18 +0200)]
USB: cdc-wdm: ignore -EPIPE from GetEncapsulatedResponse
The driver will forward errors to userspace after turning most of them
into -EIO. But all status codes are not equal. The -EPIPE (stall) in
particular can be seen more as a result of normal USB signaling than
an actual error. The state is automatically cleared by the USB core
without intervention from either driver or userspace.
And most devices and firmwares will never trigger a stall as a result
of GetEncapsulatedResponse. This is in fact a requirement for CDC WDM
devices. Quoting from section 7.1 of the CDC WMC spec revision 1.1:
The function shall not return STALL in response to
GetEncapsulatedResponse.
But this driver is also handling GetEncapsulatedResponse on behalf of
the qmi_wwan and cdc_mbim drivers. Unfortunately the relevant specs
are not as clear wrt stall. So some QMI and MBIM devices *will*
occasionally stall, causing the GetEncapsulatedResponse to return an
-EPIPE status. Translating this into -EIO for userspace has proven to
be harmful. Treating it as an empty read is safer, making the driver
behave as if the device was conforming to the CDC WDM spec.
There have been numerous reports of issues related to -EPIPE errors
from some newer CDC MBIM devices in particular, like for example the
Fibocom L831-EAU. Testing on this device has shown that the issues
go away if we simply ignore the -EPIPE status. Similar handling of
-EPIPE is already known from e.g. usb_get_string()
The -EPIPE log message is still kept to let us track devices with this
unexpected behaviour, hoping that it attracts attention from firmware
developers.
Cc: <stable@vger.kernel.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100938
Reported-and-tested-by: Christian Ehrig <christian.ehrig@mediamarktsaturn-bt.com>
Reported-and-tested-by: Patrick Chilton <chpatrick@gmail.com>
Reported-and-tested-by: Andreas Böhler <news@aboehler.at>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Carpenter [Fri, 22 Sep 2017 20:43:46 +0000 (23:43 +0300)]
USB: devio: Don't corrupt user memory
The user buffer has "uurb->buffer_length" bytes. If the kernel has more
information than that, we should truncate it instead of writing past
the end of the user's buffer. I added a WARN_ONCE() to help the user
debug the issue.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Carpenter [Fri, 22 Sep 2017 20:43:25 +0000 (23:43 +0300)]
USB: devio: Prevent integer overflow in proc_do_submiturb()
There used to be an integer overflow check in proc_do_submiturb() but
we removed it. It turns out that it's still required. The
uurb->buffer_length variable is a signed integer and it's controlled by
the user. It can lead to an integer overflow when we do:
num_sgs = DIV_ROUND_UP(uurb->buffer_length, USB_SG_SIZE);
If we strip away the macro then that line looks like this:
num_sgs = (uurb->buffer_length + USB_SG_SIZE - 1) / USB_SG_SIZE;
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
It's the first addition which can overflow.
Fixes: 1129d270cbfb ("USB: Increase usbfs transfer limit")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Thu, 21 Sep 2017 17:22:00 +0000 (13:22 -0400)]
USB: g_mass_storage: Fix deadlock when driver is unbound
As a holdover from the old g_file_storage gadget, the g_mass_storage
legacy gadget driver attempts to unregister itself when its main
operating thread terminates (if it hasn't been unregistered already).
This is not strictly necessary; it was never more than an attempt to
have the gadget fail cleanly if something went wrong and the main
thread was killed.
However, now that the UDC core manages gadget drivers independently of
UDC drivers, this scheme doesn't work any more. A simple test:
modprobe dummy-hcd
modprobe g-mass-storage file=...
rmmod dummy-hcd
ends up in a deadlock with the following backtrace:
sysrq: SysRq : Show Blocked State
task PC stack pid father
file-storage D 0 1130 2 0x00000000
Call Trace:
__schedule+0x53e/0x58c
schedule+0x6e/0x77
schedule_preempt_disabled+0xd/0xf
__mutex_lock.isra.1+0x129/0x224
? _raw_spin_unlock_irqrestore+0x12/0x14
__mutex_lock_slowpath+0x12/0x14
mutex_lock+0x28/0x2b
usb_gadget_unregister_driver+0x29/0x9b [udc_core]
usb_composite_unregister+0x10/0x12 [libcomposite]
msg_cleanup+0x1d/0x20 [g_mass_storage]
msg_thread_exits+0xd/0xdd7 [g_mass_storage]
fsg_main_thread+0x1395/0x13d6 [usb_f_mass_storage]
? __schedule+0x573/0x58c
kthread+0xd9/0xdb
? do_set_interface+0x25c/0x25c [usb_f_mass_storage]
? init_completion+0x1e/0x1e
ret_from_fork+0x19/0x24
rmmod D 0 1155 683 0x00000000
Call Trace:
__schedule+0x53e/0x58c
schedule+0x6e/0x77
schedule_timeout+0x26/0xbc
? __schedule+0x573/0x58c
do_wait_for_common+0xb3/0x128
? usleep_range+0x81/0x81
? wake_up_q+0x3f/0x3f
wait_for_common+0x2e/0x45
wait_for_completion+0x17/0x19
fsg_common_put+0x34/0x81 [usb_f_mass_storage]
fsg_free_inst+0x13/0x1e [usb_f_mass_storage]
usb_put_function_instance+0x1a/0x25 [libcomposite]
msg_unbind+0x2a/0x42 [g_mass_storage]
__composite_unbind+0x4a/0x6f [libcomposite]
composite_unbind+0x12/0x14 [libcomposite]
usb_gadget_remove_driver+0x4f/0x77 [udc_core]
usb_del_gadget_udc+0x52/0xcc [udc_core]
dummy_udc_remove+0x27/0x2c [dummy_hcd]
platform_drv_remove+0x1d/0x31
device_release_driver_internal+0xe9/0x16d
device_release_driver+0x11/0x13
bus_remove_device+0xd2/0xe2
device_del+0x19f/0x221
? selinux_capable+0x22/0x27
platform_device_del+0x21/0x63
platform_device_unregister+0x10/0x1a
cleanup+0x20/0x817 [dummy_hcd]
SyS_delete_module+0x10c/0x197
? ____fput+0xd/0xf
? task_work_run+0x55/0x62
? prepare_exit_to_usermode+0x65/0x75
do_fast_syscall_32+0x86/0xc3
entry_SYSENTER_32+0x4e/0x7c
What happens is that removing the dummy-hcd driver causes the UDC core
to unbind the gadget driver, which it does while holding the udc_lock
mutex. The unbind routine in g_mass_storage tells the main thread to
exit and waits for it to terminate.
But as mentioned above, when the main thread exits it tries to
unregister the mass-storage function driver. Via the composite
framework this ends up calling usb_gadget_unregister_driver(), which
tries to acquire the udc_lock mutex. The result is deadlock.
The simplest way to fix the problem is not to be so clever: The main
thread doesn't have to unregister the function driver. The side
effects won't be so terrible; if the gadget is still attached to a USB
host when the main thread is killed, it will appear to the host as
though the gadget's firmware has crashed -- a reasonably accurate
interpretation, and an all-too-common occurrence for USB mass-storage
devices.
In fact, the code to unregister the driver when the main thread exits
is specific to g-mass-storage; it is not used when f-mass-storage is
included as a function in a larger composite device. Therefore the
entire mechanism responsible for this (the fsg_operations structure
with its ->thread_exits method, the fsg_common_set_ops() routine, and
the msg_thread_exits() callback routine) can all be eliminated. Even
the msg_registered bitflag can be removed, because now the driver is
unregistered in only one place rather than in two places.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Thu, 21 Sep 2017 17:23:58 +0000 (13:23 -0400)]
USB: gadgetfs: Fix crash caused by inadequate synchronization
The gadgetfs driver (drivers/usb/gadget/legacy/inode.c) was written
before the UDC and composite frameworks were adopted; it is a legacy
driver. As such, it expects that once bound to a UDC controller, it
will not be unbound until it unregisters itself.
However, the UDC framework does unbind function drivers while they are
still registered. When this happens, it can cause the gadgetfs driver
to misbehave or crash. For example, userspace can cause a crash by
opening the device file and doing an ioctl call before setting up a
configuration (found by Andrey Konovalov using the syzkaller fuzzer).
This patch adds checks and synchronization to prevent these bad
behaviors. It adds a udc_usage counter that the driver increments at
times when it is using a gadget interface without holding the private
spinlock. The unbind routine waits for this counter to go to 0 before
returning, thereby ensuring that the UDC is no longer in use.
The patch also adds a check in the dev_ioctl() routine to make sure
the driver is bound to a UDC before dereferencing the gadget pointer,
and it makes destroy_ep_files() synchronize with the endpoint I/O
routines, to prevent the user from accessing an endpoint data
structure after it has been removed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
CC: <stable@vger.kernel.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Thu, 21 Sep 2017 20:12:01 +0000 (16:12 -0400)]
USB: gadgetfs: fix copy_to_user while holding spinlock
The gadgetfs driver as a long-outstanding FIXME, regarding a call of
copy_to_user() made while holding a spinlock. This patch fixes the
issue by dropping the spinlock and using the dev->udc_usage mechanism
introduced by another recent patch to guard against status changes
while the lock isn't held.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
CC: <stable@vger.kernel.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Fri, 22 Sep 2017 15:56:49 +0000 (11:56 -0400)]
USB: uas: fix bug in handling of alternate settings
The uas driver has a subtle bug in the way it handles alternate
settings. The uas_find_uas_alt_setting() routine returns an
altsetting value (the bAlternateSetting number in the descriptor), but
uas_use_uas_driver() then treats that value as an index to the
intf->altsetting array, which it isn't.
Normally this doesn't cause any problems because the various
alternate settings have bAlternateSetting values 0, 1, 2, ..., so the
value is equal to the index in the array. But this is not guaranteed,
and Andrey Konovalov used the syzkaller fuzzer with KASAN to get a
slab-out-of-bounds error by violating this assumption.
This patch fixes the bug by making uas_find_uas_alt_setting() return a
pointer to the altsetting entry rather than either the value or the
index. Pointers are less subject to misinterpretation.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
CC: Oliver Neukum <oneukum@suse.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Thu, 21 Sep 2017 19:59:30 +0000 (15:59 -0400)]
usb-storage: unusual_devs entry to fix write-access regression for Seagate external drives
Kris Lindgren reports that without the NO_WP_DETECT flag, his Seagate
external disk drive fails all write accesses. This regresssion dates
back approximately to the start of the 4.x kernel releases.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Kris Lindgren <kris.lindgren@gmail.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Thu, 21 Sep 2017 20:02:05 +0000 (16:02 -0400)]
usb-storage: fix bogus hardware error messages for ATA pass-thru devices
Ever since commit
a621bac3044e ("scsi_lib: correctly retry failed zero
length REQ_TYPE_FS commands"), people have been getting bogus error
messages for USB disk drives using ATA pass-thru. For example:
[ 1344.880193] sd 6:0:0:0: [sdb] Attached SCSI disk
[ 1345.069152] sd 6:0:0:0: [sdb] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_SENSE
[ 1345.069159] sd 6:0:0:0: [sdb] tag#0 Sense Key : Hardware Error [current] [descriptor]
[ 1345.069162] sd 6:0:0:0: [sdb] tag#0 Add. Sense: No additional sense information
[ 1345.069168] sd 6:0:0:0: [sdb] tag#0 CDB: ATA command pass through(16) 85 06 20 00 00 00 00 00 00 00 00 00 00 00 e5 00
[ 1345.172252] sd 6:0:0:0: [sdb] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_SENSE
[ 1345.172258] sd 6:0:0:0: [sdb] tag#0 Sense Key : Hardware Error [current] [descriptor]
[ 1345.172261] sd 6:0:0:0: [sdb] tag#0 Add. Sense: No additional sense information
[ 1345.172266] sd 6:0:0:0: [sdb] tag#0 CDB: ATA command pass through(12)/Blank a1 06 20 da 00 00 4f c2 00 b0 00 00
These messages can be quite annoying, because programs like udisks2
provoke them every 10 minutes or so. Other programs can also have
this effect, such as those in smartmontools.
I don't fully understand how that commit induced the SCSI core to log
these error messages, but the underlying cause for them is code added
to usb-storage by commit
f1a0743bc0e7 ("USB: storage: When a device
returns no sense data, call it a Hardware Error"). At the time it was
necessary to do this, in order to prevent an infinite retry loop with
some not-so-great mass storage devices.
However, the ATA pass-thru protocol uses SCSI sense data to return
command status values, and some devices always report Check Condition
status for ATA pass-thru commands to ensure that the host retrieves
the sense data, even if the command succeeded. This violates the USB
mass-storage protocol (Check Condition status is supposed to mean the
command failed), but we can't help that.
This patch attempts to mitigate the problem of these bogus error
reports by changing usb-storage. The HARDWARE ERROR sense key will be
inserted only for commands that aren't ATA pass-thru.
Thanks to Ewan Milne for pointing out that this mechanism was present
in usb-storage. 8 years after writing it, I had completely forgotten
its existence.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Kris Lindgren <kris.lindgren@gmail.com>
Ref: https://bugzilla.redhat.com/show_bug.cgi?id=
1351305
CC: Ewan D. Milne <emilne@redhat.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Thu, 21 Sep 2017 14:58:48 +0000 (16:58 +0200)]
USB: core: harden cdc_parse_cdc_header
Andrey Konovalov reported a possible out-of-bounds problem for the
cdc_parse_cdc_header function. He writes:
It looks like cdc_parse_cdc_header() doesn't validate buflen
before accessing buffer[1], buffer[2] and so on. The only check
present is while (buflen > 0).
So fix this issue up by properly validating the buffer length matches
what the descriptor says it is.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Thu, 21 Sep 2017 08:05:41 +0000 (10:05 +0200)]
Merge tag 'fixes-for-v4.14-rc2' of git://git./linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.14-rc2
First set of fixes for the gadget side. Not much this time around,
things have been rather calm.
In no order whatsoever, this pull request contains:
- A DMA starvation fix on dwc3 caused by some recent changes to how we
map/unmap requests
- A build error fix on the snps_udc_plat.c driver
- A fix for how to we call ->udc_set_speed()
- Spinlock recursion fix on the printer gadget
- Removal of pointless comparisons on dummy driver
Arnd Bergmann [Thu, 7 Sep 2017 14:14:31 +0000 (16:14 +0200)]
usb: gadget: dummy: fix nonsensical comparisons
gcc-8 points out two comparisons that are clearly bogus
and almost certainly not what the author intended to write:
drivers/usb/gadget/udc/dummy_hcd.c: In function 'set_link_state_by_speed':
drivers/usb/gadget/udc/dummy_hcd.c:379:31: error: bitwise comparison always evaluates to false [-Werror=tautological-compare]
USB_PORT_STAT_ENABLE) == 1 &&
^~
drivers/usb/gadget/udc/dummy_hcd.c:381:25: error: bitwise comparison always evaluates to false [-Werror=tautological-compare]
USB_SS_PORT_LS_U0) == 1 &&
^~
I looked at the code for a bit and came up with a change that makes
it look like what the author probably meant here. This makes it
look reasonable to me and to gcc, shutting up the warning.
It does of course change behavior as the two conditions are actually
evaluated rather than being hardcoded to false, and I have made no
attempt at verifying that the changed logic makes sense in the context
of a USB HCD, so that part needs to be reviewed carefully.
Fixes: 1cd8fd2887e1 ("usb: gadget: dummy_hcd: add SuperSpeed support")
Cc: Tatyana Brokhman <tlinder@codeaurora.org>
Cc: Felipe Balbi <balbi@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Randy Dunlap [Mon, 11 Sep 2017 16:24:15 +0000 (09:24 -0700)]
usb: gadget: udc: fix snps_udc_plat.c build errors
Fix build errors that happen when CONFIG_EXTCON=m and
CONFIG_USB_SNP_UDC_PLAT=y by preventing that combination in Kconfig.
CONFIG_EXTCON can still be disabled or enabled for this driver since
<linux/extcon.h> has stubs for the disabled case, but if CONFIG_EXTCON=m,
USB_SNP_UDC_PLAT is restricted to m or n (cannot be builtin).
drivers/built-in.o: In function `udc_plat_remove':
snps_udc_plat.c:(.text+0x2c4060): undefined reference to `extcon_unregister_notifier'
drivers/built-in.o: In function `udc_plat_probe':
snps_udc_plat.c:(.text+0x2c438c): undefined reference to `extcon_get_edev_by_phandle'
snps_udc_plat.c:(.text+0x2c43f2): undefined reference to `extcon_register_notifier'
snps_udc_plat.c:(.text+0x2c4416): undefined reference to `extcon_get_state'
snps_udc_plat.c:(.text+0x2c44f7): undefined reference to `extcon_unregister_notifier'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Yoshihiro Shimoda [Wed, 13 Sep 2017 06:31:33 +0000 (15:31 +0900)]
usb: gadget: function: printer: avoid spinlock recursion
If usb_gadget_giveback_request() is called in usb_ep_queue(),
this printer_write() is possible to cause spinlock recursion. So,
this patch adds spin_unlock() before calls usb_ep_queue() to avoid it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Roger Quadros [Tue, 19 Sep 2017 08:46:16 +0000 (11:46 +0300)]
usb: gadget: core: fix ->udc_set_speed() logic
Consider the following case: udc controller supports SuperSpeed. If we
first load a HighSpeed gadget followed by a SuperSpeed gadget, the
SuperSpeed gadget will be limited to HighSpeed as UDC core driver
doesn't call ->udc_set_speed() in the second case.
Call ->udc_set_speed() unconditionally to fix this issue.
This will also fix the case for dwc3 controller driver when SuperSpeed
gadget is loaded first and works in HighSpeed only as udc_set_speed()
was never being called.
Fixes: 6099eca796ae ("usb: gadget: core: introduce ->udc_set_speed() method")
Cc: <stable@vger.kernel.org> [v4.13+]
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Greg Kroah-Hartman [Tue, 19 Sep 2017 13:07:17 +0000 (15:07 +0200)]
USB: fix out-of-bounds in usb_set_configuration
Andrey Konovalov reported a possible out-of-bounds problem for a USB interface
association descriptor. He writes:
It seems there's no proper size check of a USB_DT_INTERFACE_ASSOCIATION
descriptor. It's only checked that the size is >= 2 in
usb_parse_configuration(), so find_iad() might do out-of-bounds access
to intf_assoc->bInterfaceCount.
And he's right, we don't check for crazy descriptors of this type very well, so
resolve this problem. Yet another issue found by syzkaller...
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kai-Heng Feng [Mon, 18 Sep 2017 14:39:19 +0000 (17:39 +0300)]
Revert "xhci: Limit USB2 port wake support for AMD Promontory hosts"
This reverts commit
dec08194ffeccfa1cf085906b53d301930eae18f.
Commit
dec08194ffec ("xhci: Limit USB2 port wake support for AMD Promontory
hosts") makes all high speed USB ports on ASUS PRIME B350M-A cease to
function after enabling runtime PM.
All boards with this chipsets will be affected, so revert the commit.
The original patch was added to stable 4.9, 4.11 and 4.12 and needs
to reverted from there as well
Cc: <stable@vger.kernel.org> # 4.9+
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Nyman [Mon, 18 Sep 2017 14:39:18 +0000 (17:39 +0300)]
xhci: set missing SuperSpeedPlus Link Protocol bit in roothub descriptor
A SuperSpeedPlus roothub needs to have the Link Protocol (LP) bit set in
the bmSublinkSpeedAttr[] entry of a SuperSpeedPlus descriptor.
If the xhci controller has an optional Protocol Speed ID (PSI) table then
that will be used as a base to create the roothub SuperSpeedPlus
descriptor.
The PSI table does not however necessary contain the LP bit so we need
to set it manually.
Check the psi speed and set LP bit if speed is 10Gbps or higher.
We're not setting it for 5 to 10Gbps as USB 3.1 specification always
mention SuperSpeedPlus for 10Gbps or higher, and some SSIC USB 3.0 speeds
can be over 5Gbps, such as SSIC-G3B-L1 at 5830 Mbps
Cc: <stable@vger.kernel.org> # 4.6+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Nyman [Mon, 18 Sep 2017 14:39:17 +0000 (17:39 +0300)]
xhci: Fix sleeping with spin_lock_irq() held in ASmedia 1042A workaround
The flow control workaround for ASM1042A xHC hosts sleeps between
register polling. The workaround gets called in several places, among
them with spin_lock_irq() held when xHC host is resumed or hoplug removed.
This was noticed as kernel panics at resume on a Dell XPS15 9550 with
TB16 thunderbolt dock.
Avoid sleeping with spin_lock_irq() held, use udelay() instead
The original workaround was added to 4.9 and 4.12 stable releases,
this patch needs to be applied to those as well.
Fixes: 9da5a1092b13 ("xhci: Bad Ethernet performance plugged in ASM1042A host")
Cc: <stable@vger.kernel.org> #4.9+
Reported-by: Jose Marino <marinoj@nso.edu>
Tested-by: Jose Marino <marinoj@nso.edu>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adam Wallis [Mon, 18 Sep 2017 14:39:16 +0000 (17:39 +0300)]
usb: host: xhci-plat: allow sysdev to inherit from ACPI
Commit
4c39d4b949d3 ("usb: xhci: use bus->sysdev for DMA configuration")
updated the method determining DMA for XHCI from sysdev. However, this
patch broke the ability to enumerate the FWNODE from parent ACPI devices
from the child plat XHCI device.
Currently, xhci_plat is not set up properly when the parent device is an
ACPI node. The conditions that xhci_plat_probe should satisfy are
1. xhci_plat comes from firmware
2. xhci_plat is child of a device from firmware (dwc3-plat)
3. xhci_plat is grandchild of a pci device (dwc3-pci)
Case 2 is covered when the child is an OF node (by checking
sysdev->parent->of_node), however, an ACPI parent will return NULL in
the of_node check and will thus not result in sysdev being set to
sysdev->parent
[ 17.591549] xhci-hcd: probe of xhci-hcd.6.auto failed with error -5
This change adds a check for ACPI to completely allow for condition 2.
This is done by first checking if the parent node is of type ACPI (e.g.,
dwc3-plat) and set sysdev to sysdev->parent if either of the two
following conditions are met:
1: If fwnode is empty (in the case that platform_device_add_properties
was not called on the allocated platform device)
2: fwnode exists but is not of type ACPI (this would happen if
platform_device_add_properties was called on the allocated device.
Instead of type FWNODE_ACPI, you would end up with FWNODE_PDATA)
Cc: stable@vger.kernel.org #4.12.x
Cc: stable@vger.kernel.org #4.13.x
Fixes: 4c39d4b949d3 ("usb: xhci: use bus->sysdev for DMA configuration")
Tested-by: Thang Q. Nguyen <tqnguyen@apm.com>
Signed-off-by: Adam Wallis <awallis@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Nyman [Mon, 18 Sep 2017 14:39:15 +0000 (17:39 +0300)]
xhci: fix wrong endpoint ESIT value shown in tracing
Read the endpiont ESIT from endpiont context using correct macro.
Add a macro for reading the high bits of ESIT for Large ESIT Payload
Capable hosts (LEC=1)
Cc: <stable@vger.kernel.org> # 4.12
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jim Dickerson [Mon, 18 Sep 2017 14:39:14 +0000 (17:39 +0300)]
usb: pci-quirks.c: Corrected timeout values used in handshake
Servers were emitting failed handoff messages but were not
waiting the full 1 second as designated in section 4.22.1 of
the eXtensible Host Controller Interface specifications. The
handshake was using wrong units so calls were made with milliseconds
not microseconds. Comments referenced 5 seconds not 1 second as
in specs.
The wrong units were also corrected in a second handshake call.
Cc: <stable@vger.kernel.org>
Signed-off-by: Jim Dickerson <jim.dickerson@hpe.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Nyman [Mon, 18 Sep 2017 14:39:13 +0000 (17:39 +0300)]
xhci: fix finding correct bus_state structure for USB 3.1 hosts
xhci driver keeps a bus_state structure for each hcd (usb2 and usb3)
The structure is picked based on hcd speed, but driver only compared
for HCD_USB3 speed, returning the wrong bus_state for HCD_USB31 hosts.
This caused null pointer dereference errors in bus_resume function.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lu Baolu [Mon, 18 Sep 2017 14:39:12 +0000 (17:39 +0300)]
usb: xhci: Free the right ring in xhci_add_endpoint()
In the xhci_add_endpoint(), a new ring was allocated and saved at
xhci_virt_ep->new_ring. Hence, when error happens, we need to free
the allocated ring before returning error.
Current code frees xhci_virt_ep->ring instead of the new_ring. This
patch fixes this.
Cc: <stable@vger.kernel.org>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Felipe Balbi [Mon, 11 Sep 2017 07:45:12 +0000 (10:45 +0300)]
usb: dwc3: ep0: fix DMA starvation by assigning req->trb on ep0
If we don't assign a TRB to ep0 requests, we won't be able to unmap
the request later on resulting in starvation of DMA resources.
Fixes: 4a71fcb8ac5f ("usb: dwc3: gadget: only unmap requests from DMA if mapped")
Reported-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Tested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Dmitry Fleytman [Tue, 5 Sep 2017 08:40:56 +0000 (11:40 +0300)]
usb: Increase quirk delay for USB devices
Commit
e0429362ab15
("usb: Add device quirk for Logitech HD Pro Webcams C920 and C930e")
introduced quirk to workaround an issue with some Logitech webcams.
The workaround is introducing delay for some USB operations.
According to our testing, delay introduced by original commit
is not long enough and in rare cases we still see issues described
by the aforementioned commit.
This patch increases delays introduced by original commit.
Having this patch applied we do not see those problems anymore.
Signed-off-by: Dmitry Fleytman <dmitry@daynix.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andrey Konovalov [Thu, 14 Sep 2017 12:30:55 +0000 (14:30 +0200)]
uwb: properly check kthread_run return value
uwbd_start() calls kthread_run() and checks that the return value is
not NULL. But the return value is not NULL in case kthread_run() fails,
it takes the form of ERR_PTR(-EINTR).
Use IS_ERR() instead.
Also add a check to uwbd_stop().
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andrey Konovalov [Thu, 14 Sep 2017 14:52:59 +0000 (16:52 +0200)]
uwb: ensure that endpoint is interrupt
hwarc_neep_init() assumes that endpoint 0 is interrupt, but there's no
check for that, which results in a WARNING in USB core code, when a bad
USB descriptor is provided from a device:
usb 1-1: BOGUS urb xfer, pipe 1 != type 3
------------[ cut here ]------------
WARNING: CPU: 0 PID: 3 at drivers/usb/core/urb.c:449 usb_submit_urb+0xf8a/0x11d0
Modules linked in:
CPU: 0 PID: 3 Comm: kworker/0:0 Not tainted 4.13.0+ #111
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Workqueue: usb_hub_wq hub_event
task:
ffff88006bdc1a00 task.stack:
ffff88006bde8000
RIP: 0010:usb_submit_urb+0xf8a/0x11d0 drivers/usb/core/urb.c:448
RSP: 0018:
ffff88006bdee3c0 EFLAGS:
00010282
RAX:
0000000000000029 RBX:
ffff8800672a7200 RCX:
0000000000000000
RDX:
0000000000000029 RSI:
ffff88006c815c78 RDI:
ffffed000d7bdc6a
RBP:
ffff88006bdee4c0 R08:
fffffbfff0fe00ff R09:
fffffbfff0fe00ff
R10:
0000000000000018 R11:
fffffbfff0fe00fe R12:
1ffff1000d7bdc7f
R13:
0000000000000003 R14:
0000000000000001 R15:
ffff88006b02cc90
FS:
0000000000000000(0000) GS:
ffff88006c800000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
00007fe4daddf000 CR3:
000000006add6000 CR4:
00000000000006f0
Call Trace:
hwarc_neep_init+0x4ce/0x9c0 drivers/uwb/hwa-rc.c:710
uwb_rc_add+0x2fb/0x730 drivers/uwb/lc-rc.c:361
hwarc_probe+0x34e/0x9b0 drivers/uwb/hwa-rc.c:858
usb_probe_interface+0x351/0x8d0 drivers/usb/core/driver.c:361
really_probe drivers/base/dd.c:385
driver_probe_device+0x610/0xa00 drivers/base/dd.c:529
__device_attach_driver+0x230/0x290 drivers/base/dd.c:625
bus_for_each_drv+0x15e/0x210 drivers/base/bus.c:463
__device_attach+0x269/0x3c0 drivers/base/dd.c:682
device_initial_probe+0x1f/0x30 drivers/base/dd.c:729
bus_probe_device+0x1da/0x280 drivers/base/bus.c:523
device_add+0xcf9/0x1640 drivers/base/core.c:1703
usb_set_configuration+0x1064/0x1890 drivers/usb/core/message.c:1932
generic_probe+0x73/0xe0 drivers/usb/core/generic.c:174
usb_probe_device+0xaf/0xe0 drivers/usb/core/driver.c:266
really_probe drivers/base/dd.c:385
driver_probe_device+0x610/0xa00 drivers/base/dd.c:529
__device_attach_driver+0x230/0x290 drivers/base/dd.c:625
bus_for_each_drv+0x15e/0x210 drivers/base/bus.c:463
__device_attach+0x269/0x3c0 drivers/base/dd.c:682
device_initial_probe+0x1f/0x30 drivers/base/dd.c:729
bus_probe_device+0x1da/0x280 drivers/base/bus.c:523
device_add+0xcf9/0x1640 drivers/base/core.c:1703
usb_new_device+0x7b8/0x1020 drivers/usb/core/hub.c:2457
hub_port_connect drivers/usb/core/hub.c:4890
hub_port_connect_change drivers/usb/core/hub.c:4996
port_event drivers/usb/core/hub.c:5102
hub_event+0x23c8/0x37c0 drivers/usb/core/hub.c:5182
process_one_work+0x9fb/0x1570 kernel/workqueue.c:2097
worker_thread+0x1e4/0x1350 kernel/workqueue.c:2231
kthread+0x324/0x3f0 kernel/kthread.c:231
ret_from_fork+0x25/0x30 arch/x86/entry/entry_64.S:425
Code: 48 8b 85 30 ff ff ff 48 8d b8 98 00 00 00 e8 8e 93 07 ff 45 89
e8 44 89 f1 4c 89 fa 48 89 c6 48 c7 c7 a0 e5 55 86 e8 20 08 8f fd <0f>
ff e9 9b f7 ff ff e8 4a 04 d6 fd e9 80 f7 ff ff e8 60 11 a6
---[ end trace
55d741234124cfc3 ]---
Check that endpoint is interrupt.
Found by syzkaller.
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Sat, 16 Sep 2017 22:47:51 +0000 (15:47 -0700)]
Linux 4.14-rc1
Linus Torvalds [Sat, 16 Sep 2017 19:08:10 +0000 (12:08 -0700)]
Merge tag 'upstream-4.14-rc1' of git://git.infradead.org/linux-ubifs
Pull UBI updates from Richard Weinberger:
"Minor improvements"
* tag 'upstream-4.14-rc1' of git://git.infradead.org/linux-ubifs:
UBI: Fix two typos in comments
ubi: fastmap: fix spelling mistake: "invalidiate" -> "invalidate"
ubi: pr_err() strings should end with newlines
ubi: pr_err() strings should end with newlines
ubi: pr_err() strings should end with newlines
Linus Torvalds [Sat, 16 Sep 2017 19:03:25 +0000 (12:03 -0700)]
Merge branch 'for-linus-4.14-rc1' of git://git./linux/kernel/git/rw/uml
Pull UML updates from Richard Weinberger:
- minor improvements
- fixes for Debian's new gcc defaults (pie enabled by default)
- fixes for XSTATE/XSAVE to make UML work again on modern systems
* 'for-linus-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
um: return negative in tuntap_open_tramp()
um: remove a stray tab
um: Use relative modversions with LD_SCRIPT_DYN
um: link vmlinux with -no-pie
um: Fix CONFIG_GCOV for modules.
Fix minor typos and grammar in UML start_up help
um: defconfig: Cleanup from old Kconfig options
um: Fix FP register size for XSTATE/XSAVE
Linus Torvalds [Sat, 16 Sep 2017 18:28:59 +0000 (11:28 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Fix hotplug deadlock in hv_netvsc, from Stephen Hemminger.
2) Fix double-free in rmnet driver, from Dan Carpenter.
3) INET connection socket layer can double put request sockets, fix
from Eric Dumazet.
4) Don't match collect metadata-mode tunnels if the device is down,
from Haishuang Yan.
5) Do not perform TSO6/GSO on ipv6 packets with extensions headers in
be2net driver, from Suresh Reddy.
6) Fix scaling error in gen_estimator, from Eric Dumazet.
7) Fix 64-bit statistics deadlock in systemport driver, from Florian
Fainelli.
8) Fix use-after-free in sctp_sock_dump, from Xin Long.
9) Reject invalid BPF_END instructions in verifier, from Edward Cree.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
mlxsw: spectrum_router: Only handle IPv4 and IPv6 events
Documentation: link in networking docs
tcp: fix data delivery rate
bpf/verifier: reject BPF_ALU64|BPF_END
sctp: do not mark sk dumped when inet_sctp_diag_fill returns err
sctp: fix an use-after-free issue in sctp_sock_dump
netvsc: increase default receive buffer size
tcp: update skb->skb_mstamp more carefully
net: ipv4: fix l3slave check for index returned in IP_PKTINFO
net: smsc911x: Quieten netif during suspend
net: systemport: Fix 64-bit stats deadlock
net: vrf: avoid gcc-4.6 warning
qed: remove unnecessary call to memset
tg3: clean up redundant initialization of tnapi
tls: make tls_sw_free_resources static
sctp: potential read out of bounds in sctp_ulpevent_type_enabled()
MAINTAINERS: review Renesas DT bindings as well
net_sched: gen_estimator: fix scaling error in bytes/packets samples
nfp: wait for the NSP resource to appear on boot
nfp: wait for board state before talking to the NSP
...
Linus Torvalds [Sat, 16 Sep 2017 18:24:26 +0000 (11:24 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
Pull more input updates from Dmitry Torokhov:
"A second round of updates for the input subsystem:
- a new driver for PWM-controlled vibrators
- ucb1400 touchscreen driver had completely busted suspend/resume
handling
- we now handle "home" button found on some devices with Goodix
touchscreens
- assorted other fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: i8042 - add Gigabyte P57 to the keyboard reset table
Input: xpad - validate USB endpoint type during probe
Input: ucb1400_ts - fix suspend and resume handling
Input: edt-ft5x06 - fix access to non-existing register
Input: elantech - make arrays debounce_packet static, reduces object code size
Input: surface3_spi - make const array header static, reduces object code size
Input: goodix - add support for capacitive home button
Input: add a driver for PWM controllable vibrators
Input: adi - make array seq static, reduces object code size
Markus Trippelsdorf [Sat, 16 Sep 2017 09:01:16 +0000 (11:01 +0200)]
firmware: Restore support for built-in firmware
Commit
5620a0d1aac ("firmware: delete in-kernel firmware") removed the
entire firmware directory. Unfortunately it thereby also removed the
support for built-in firmware.
This restores the ability to build firmware directly into the kernel by
pruning the original Makefile to the necessary minimum. The default for
EXTRA_FIRMWARE_DIR is now the standard directory /lib/firmware/.
Fixes: 5620a0d1aac ("firmware: delete in-kernel firmware")
Signed-off-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Acked-by: Greg K-H <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ido Schimmel [Fri, 15 Sep 2017 13:31:07 +0000 (15:31 +0200)]
mlxsw: spectrum_router: Only handle IPv4 and IPv6 events
The driver doesn't support events from address families other than IPv4
and IPv6, so ignore them. Otherwise, we risk queueing a work item before
it's initialized.
This can happen in case a VRF is configured when MROUTE_MULTIPLE_TABLES
is enabled, as the VRF driver will try to add an l3mdev rule for the
IPMR family.
Fixes: 65e65ec137f4 ("mlxsw: spectrum_router: Don't ignore IPv6 notifications")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Andreas Rammhold <andreas@rammhold.de>
Reported-by: Florian Klink <flokli@flokli.de>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Machek [Sat, 16 Sep 2017 14:28:02 +0000 (16:28 +0200)]
Documentation: link in networking docs
Fix link in filter.txt.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 15 Sep 2017 23:47:42 +0000 (16:47 -0700)]
tcp: fix data delivery rate
Now skb->mstamp_skb is updated later, we also need to call
tcp_rate_skb_sent() after the update is done.
Fixes: 8c72c65b426b ("tcp: update skb->skb_mstamp more carefully")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 16 Sep 2017 03:43:33 +0000 (20:43 -0700)]
Merge branch '4.14-features' of git://git.linux-mips.org/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 4.14 for MIPS; below a summary of
the non-merge commits:
CM:
- Rename mips_cm_base to mips_gcr_base
- Specify register size when generating accessors
- Use BIT/GENMASK for register fields, order & drop shifts
- Add cluster & block args to mips_cm_lock_other()
CPC:
- Use common CPS accessor generation macros
- Use BIT/GENMASK for register fields, order & drop shifts
- Introduce register modify (set/clear/change) accessors
- Use change_*, set_* & clear_* where appropriate
- Add CM/CPC 3.5 register definitions
- Use GlobalNumber macros rather than magic numbers
- Have asm/mips-cps.h include CM & CPC headers
- Cluster support for topology functions
- Detect CPUs in secondary clusters
CPS:
- Read GIC_VL_IDENT directly, not via irqchip driver
DMA:
- Consolidate coherent and non-coherent dma_alloc code
- Don't use dma_cache_sync to implement fd_cacheflush
FPU emulation / FP assist code:
- Another series of 14 commits fixing corner cases such as NaN
propgagation and other special input values.
- Zero bits 32-63 of the result for a CLASS.D instruction.
- Enhanced statics via debugfs
- Do not use bools for arithmetic. GCC 7.1 moans about this.
- Correct user fault_addr type
Generic MIPS:
- Enhancement of stack backtraces
- Cleanup from non-existing options
- Handle non word sized instructions when examining frame
- Fix detection and decoding of ADDIUSP instruction
- Fix decoding of SWSP16 instruction
- Refactor handling of stack pointer in get_frame_info
- Remove unreachable code from force_fcr31_sig()
- Convert to using %pOF instead of full_name
- Remove the R6000 support.
- Move FP code from *_switch.S to *_fpu.S
- Remove unused ST_OFF from r2300_switch.S
- Allow platform to specify multiple its.S files
- Add #includes to various files to ensure code builds reliable and
without warning..
- Remove __invalidate_kernel_vmap_range
- Remove plat_timer_setup
- Declare various variables & functions static
- Abstract CPU core & VP(E) ID access through accessor functions
- Store core & VP IDs in GlobalNumber-style variable
- Unify checks for sibling CPUs
- Add CPU cluster number accessors
- Prevent direct use of generic_defconfig
- Make CONFIG_MIPS_MT_SMP default y
- Add __ioread64_copy
- Remove unnecessary inclusions of linux/irqchip/mips-gic.h
GIC:
- Introduce asm/mips-gic.h with accessor functions
- Use new GIC accessor functions in mips-gic-timer
- Remove counter access functions from irq-mips-gic.c
- Remove gic_read_local_vp_id() from irq-mips-gic.c
- Simplify shared interrupt pending/mask reads in irq-mips-gic.c
- Simplify gic_local_irq_domain_map() in irq-mips-gic.c
- Drop gic_(re)set_mask() functions in irq-mips-gic.c
- Remove gic_set_polarity(), gic_set_trigger(), gic_set_dual_edge(),
gic_map_to_pin() and gic_map_to_vpe() from irq-mips-gic.c.
- Convert remaining shared reg access, local int mask access and
remaining local reg access to new accessors
- Move GIC_LOCAL_INT_* to asm/mips-gic.h
- Remove GIC_CPU_INT* macros from irq-mips-gic.c
- Move various definitions to the driver
- Remove gic_get_usm_range()
- Remove __gic_irq_dispatch() forward declaration
- Remove gic_init()
- Use mips_gic_present() in place of gic_present and remove
gic_present
- Move gic_get_c0_*_int() to asm/mips-gic.h
- Remove linux/irqchip/mips-gic.h
- Inline __gic_init()
- Inline gic_basic_init()
- Make pcpu_masks a per-cpu variable
- Use pcpu_masks to avoid reading GIC_SH_MASK*
- Clean up mti, reserved-cpu-vectors handling
- Use cpumask_first_and() in gic_set_affinity()
- Let the core set struct irq_common_data affinity
microMIPS:
- Fix microMIPS stack unwinding on big endian systems
MIPS-GIC:
- SYNC after enabling GIC region
NUMA:
- Remove the unused parent_node() macro
R6:
- Constify r2_decoder_tables
- Add accessor & bit definitions for GlobalNumber
SMP:
- Constify smp ops
- Allow boot_secondary SMP op to return errors
VDSO:
- Drop gic_get_usm_range() usage
- Avoid use of linux/irqchip/mips-gic.h
Platform changes:
Alchemy:
- Add devboard machine type to cpuinfo
- update cpu feature overrides
- Threaded carddetect irqs for devboards
AR7:
- allow NULL clock for clk_get_rate
BCM63xx:
- Fix ENETDMA_6345_MAXBURST_REG offset
- Allow NULL clock for clk_get_rate
CI20:
- Enable GPIO and RTC drivers in defconfig
- Add ethernet and fixed-regulator nodes to DTS
Generic platform:
- Move Boston and NI 169445 FIT image source to their own files
- Include asm/bootinfo.h for plat_fdt_relocated()
- Include asm/time.h for get_c0_*_int()
- Include asm/bootinfo.h for plat_fdt_relocated()
- Include asm/time.h for get_c0_*_int()
- Allow filtering enabled boards by requirements
- Don't explicitly disable CONFIG_USB_SUPPORT
- Bump default NR_CPUS to 16
JZ4700:
- Probe the jz4740-rtc driver from devicetree
Lantiq:
- Drop check of boot select from the spi-falcon driver.
- Drop check of boot select from the lantiq-flash MTD driver.
- Access boot cause register in the watchdog driver through regmap
- Add device tree binding documentation for the watchdog driver
- Add docs for the RCU DT bindings.
- Convert the fpi bus driver to a platform_driver
- Remove ltq_reset_cause() and ltq_boot_select(
- Switch to a proper reset driver
- Switch to a new drivers/soc GPHY driver
- Add an USB PHY driver for the Lantiq SoCs using the RCU module
- Use of_platform_default_populate instead of __dt_register_buses
- Enable MFD_SYSCON to be able to use it for the RCU MFD
- Replace ltq_boot_select() with dummy implementation.
Loongson 2F:
- Allow NULL clock for clk_get_rate
Malta:
- Use new GIC accessor functions
NI 169445:
- Add support for NI 169445 board.
- Only include in 32r2el kernels
Octeon:
- Add support for watchdog of 78XX SOCs.
- Add support for watchdog of CN68XX SOCs.
- Expose support for mips32r1, mips32r2 and mips64r1
- Enable more drivers in config file
- Add support for accessing the boot vector.
- Remove old boot vector code from watchdog driver
- Define watchdog registers for 70xx, 73xx, 78xx, F75xx.
- Make CSR functions node aware.
- Allow access to CIU3 IRQ domains.
- Misc cleanups in the watchdog driver
Omega2+:
- New board, add support and defconfig
Pistachio:
- Enable Root FS on NFS in defconfig
Ralink:
- Add Mediatek MT7628A SoC
- Allow NULL clock for clk_get_rate
- Explicitly request exclusive reset control in the pci-mt7620 PCI driver.
SEAD3:
- Only include in 32 bit kernels by default
VoCore:
- Add VoCore as a vendor t0 dt-bindings
- Add defconfig file"
* '4.14-features' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (167 commits)
MIPS: Refactor handling of stack pointer in get_frame_info
MIPS: Stacktrace: Fix microMIPS stack unwinding on big endian systems
MIPS: microMIPS: Fix decoding of swsp16 instruction
MIPS: microMIPS: Fix decoding of addiusp instruction
MIPS: microMIPS: Fix detection of addiusp instruction
MIPS: Handle non word sized instructions when examining frame
MIPS: ralink: allow NULL clock for clk_get_rate
MIPS: Loongson 2F: allow NULL clock for clk_get_rate
MIPS: BCM63XX: allow NULL clock for clk_get_rate
MIPS: AR7: allow NULL clock for clk_get_rate
MIPS: BCM63XX: fix ENETDMA_6345_MAXBURST_REG offset
mips: Save all registers when saving the frame
MIPS: Add DWARF unwinding to assembly
MIPS: Make SAVE_SOME more standard
MIPS: Fix issues in backtraces
MIPS: jz4780: DTS: Probe the jz4740-rtc driver from devicetree
MIPS: Ci20: Enable RTC driver
watchdog: octeon-wdt: Add support for 78XX SOCs.
watchdog: octeon-wdt: Add support for cn68XX SOCs.
watchdog: octeon-wdt: File cleaning.
...
Linus Torvalds [Sat, 16 Sep 2017 03:25:06 +0000 (20:25 -0700)]
Merge tag 'pci-v4.14-fixes-1' of git://git./linux/kernel/git/helgaas/pci
Pull PCI fix from Bjorn Helgaas:
"Revert an attempt to fix a race while enabling upstream bridges
because it broke iwlwifi firmware loading"
* tag 'pci-v4.14-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
Revert "PCI: Avoid race while enabling upstream bridges"
Linus Torvalds [Sat, 16 Sep 2017 00:52:52 +0000 (17:52 -0700)]
Merge tag 'drm-fixes-for-v4.14-rc1' of git://people.freedesktop.org/~airlied/linux
Pull drm AMD fixes from Dave Airlie:
"Just had a single AMD fixes pull from Alex for rc1"
* tag 'drm-fixes-for-v4.14-rc1' of git://people.freedesktop.org/~airlied/linux:
drm/amdgpu: revert "fix deadlock of reservation between cs and gpu reset v2"
drm/amdgpu: remove duplicate return statement
drm/amdgpu: check memory allocation failure
drm/amd/amdgpu: fix BANK_SELECT on Vega10 (v2)
drm/amdgpu: inline amdgpu_ttm_do_bind again
drm/amdgpu: fix amdgpu_ttm_bind
drm/amdgpu: remove the GART copy hack
drm/ttm:fix wrong decoding of bo_count
drm/ttm: fix missing inc bo_count
drm/amdgpu: set sched_hw_submission higher for KIQ (v3)
drm/amdgpu: move default gart size setting into gmc modules
drm/amdgpu: refine default gart size
drm/amd/powerplay: ACG frequency added in PPTable
drm/amdgpu: discard commands of killed processes
drm/amdgpu: fix and cleanup shadow handling
drm/amdgpu: add automatic per asic settings for gart_size
drm/amdgpu/gfx8: fix spelling typo in mqd allocation
drm/amd/powerplay: unhalt mec after loading
drm/amdgpu/virtual_dce: Virtual display doesn't support disable vblank immediately
drm/amdgpu: Fix huge page updates with CPU
Linus Torvalds [Sat, 16 Sep 2017 00:49:46 +0000 (17:49 -0700)]
Merge branch 'i2c/for-next' of git://git./linux/kernel/git/wsa/linux
Pull more i2c updates from Wolfram Sang:
"I2C has two more new drivers: Altera FPGA and STM32F7"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: i2c-stm32f7: add driver
i2c: i2c-stm32f4: use generic definition of speed enum
dt-bindings: i2c-stm32: Document the STM32F7 I2C bindings
i2c: altera: Add Altera I2C Controller driver
dt-bindings: i2c: Add Altera I2C Controller
Linus Torvalds [Fri, 15 Sep 2017 22:43:55 +0000 (15:43 -0700)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull more KVM updates from Paolo Bonzini:
- PPC bugfixes
- RCU splat fix
- swait races fix
- pointless userspace-triggerable BUG() fix
- misc fixes for KVM_RUN corner cases
- nested virt correctness fixes + one host DoS
- some cleanups
- clang build fix
- fix AMD AVIC with default QEMU command line options
- x86 bugfixes
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (28 commits)
kvm: nVMX: Handle deferred early VMLAUNCH/VMRESUME failure properly
kvm: vmx: Handle VMLAUNCH/VMRESUME failure properly
kvm: nVMX: Remove nested_vmx_succeed after successful VM-entry
kvm,mips: Fix potential swait_active() races
kvm,powerpc: Serialize wq active checks in ops->vcpu_kick
kvm: Serialize wq active checks in kvm_vcpu_wake_up()
kvm,x86: Fix apf_task_wake_one() wq serialization
kvm,lapic: Justify use of swait_active()
kvm,async_pf: Use swq_has_sleeper()
sched/wait: Add swq_has_sleeper()
KVM: VMX: Do not BUG() on out-of-bounds guest IRQ
KVM: Don't accept obviously wrong gsi values via KVM_IRQFD
kvm: nVMX: Don't allow L2 to access the hardware CR8
KVM: trace events: update list of exit reasons
KVM: async_pf: Fix #DF due to inject "Page not Present" and "Page Ready" exceptions simultaneously
KVM: X86: Don't block vCPU if there is pending exception
KVM: SVM: Add irqchip_split() checks before enabling AVIC
KVM: Add struct kvm_vcpu pointer parameter to get_enable_apicv()
KVM: SVM: Refactor AVIC vcpu initialization into avic_init_vcpu()
KVM: x86: fix clang build
...
Edward Cree [Fri, 15 Sep 2017 13:37:38 +0000 (14:37 +0100)]
bpf/verifier: reject BPF_ALU64|BPF_END
Neither ___bpf_prog_run nor the JITs accept it.
Also adds a new test case.
Fixes: 17a5267067f3 ("bpf: verifier (add verifier core)")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Fri, 15 Sep 2017 03:02:48 +0000 (11:02 +0800)]
sctp: do not mark sk dumped when inet_sctp_diag_fill returns err
sctp_diag would not actually dump out sk/asoc if inet_sctp_diag_fill
returns err, in which case it shouldn't mark sk dumped by setting
cb->args[3] as 1 in sctp_sock_dump().
Otherwise, it could cause some asocs to have no parent's sk dumped
in 'ss --sctp'.
So this patch is to not set cb->args[3] when inet_sctp_diag_fill()
returns err in sctp_sock_dump().
Fixes: 8f840e47f190 ("sctp: add the sctp_diag.c file")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Fri, 15 Sep 2017 03:02:21 +0000 (11:02 +0800)]
sctp: fix an use-after-free issue in sctp_sock_dump
Commit
86fdb3448cc1 ("sctp: ensure ep is not destroyed before doing the
dump") tried to fix an use-after-free issue by checking !sctp_sk(sk)->ep
with holding sock and sock lock.
But Paolo noticed that endpoint could be destroyed in sctp_rcv without
sock lock protection. It means the use-after-free issue still could be
triggered when sctp_rcv put and destroy ep after sctp_sock_dump checks
!ep, although it's pretty hard to reproduce.
I could reproduce it by mdelay in sctp_rcv while msleep in sctp_close
and sctp_sock_dump long time.
This patch is to add another param cb_done to sctp_for_each_transport
and dump ep->assocs with holding tsp after jumping out of transport's
traversal in it to avoid this issue.
It can also improve sctp diag dump to make it run faster, as no need
to save sk into cb->args[5] and keep calling sctp_for_each_transport
any more.
This patch is also to use int * instead of int for the pos argument
in sctp_for_each_transport, which could make postion increment only
in sctp_for_each_transport and no need to keep changing cb->args[2]
in sctp_sock_filter and sctp_sock_dump any more.
Fixes: 86fdb3448cc1 ("sctp: ensure ep is not destroyed before doing the dump")
Reported-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Thu, 14 Sep 2017 16:31:07 +0000 (09:31 -0700)]
netvsc: increase default receive buffer size
The default receive buffer size was reduced by recent change
to a value which was appropriate for 10G and Windows Server 2016.
But the value is too small for full performance with 40G on Azure.
Increase the default back to maximum supported by host.
Fixes: 8b5327975ae1 ("netvsc: allow controlling send/recv buffer size")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 14 Sep 2017 03:30:39 +0000 (20:30 -0700)]
tcp: update skb->skb_mstamp more carefully
liujian reported a problem in TCP_USER_TIMEOUT processing with a patch
in tcp_probe_timer() :
https://www.spinics.net/lists/netdev/msg454496.html
After investigations, the root cause of the problem is that we update
skb->skb_mstamp of skbs in write queue, even if the attempt to send a
clone or copy of it failed. One reason being a routing problem.
This patch prevents this, solving liujian issue.
It also removes a potential RTT miscalculation, since
__tcp_retransmit_skb() is not OR-ing TCP_SKB_CB(skb)->sacked with
TCPCB_EVER_RETRANS if a failure happens, but skb->skb_mstamp has
been changed.
A future ACK would then lead to a very small RTT sample and min_rtt
would then be lowered to this too small value.
Tested:
# cat user_timeout.pkt
--local_ip=192.168.102.64
0 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
+0 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
+0 bind(3, ..., ...) = 0
+0 listen(3, 1) = 0
+0 `ifconfig tun0 192.168.102.64/16; ip ro add 192.0.2.1 dev tun0`
+0 < S 0:0(0) win 0 <mss 1460>
+0 > S. 0:0(0) ack 1 <mss 1460>
+.1 < . 1:1(0) ack 1 win 65530
+0 accept(3, ..., ...) = 4
+0 setsockopt(4, SOL_TCP, TCP_USER_TIMEOUT, [3000], 4) = 0
+0 write(4, ..., 24) = 24
+0 > P. 1:25(24) ack 1 win 29200
+.1 < . 1:1(0) ack 25 win 65530
//change the ipaddress
+1 `ifconfig tun0 192.168.0.10/16`
+1 write(4, ..., 24) = 24
+1 write(4, ..., 24) = 24
+1 write(4, ..., 24) = 24
+1 write(4, ..., 24) = 24
+0 `ifconfig tun0 192.168.102.64/16`
+0 < . 1:2(1) ack 25 win 65530
+0 `ifconfig tun0 192.168.0.10/16`
+3 write(4, ..., 24) = -1
# ./packetdrill user_timeout.pkt
Signed-off-by: Eric Dumazet <edumazet@googl.com>
Reported-by: liujian <liujian56@huawei.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 14 Sep 2017 00:11:37 +0000 (17:11 -0700)]
net: ipv4: fix l3slave check for index returned in IP_PKTINFO
rt_iif is only set to the actual egress device for the output path. The
recent change to consider the l3slave flag when returning IP_PKTINFO
works for local traffic (the correct device index is returned), but it
broke the more typical use case of packets received from a remote host
always returning the VRF index rather than the original ingress device.
Update the fixup to consider l3slave and rt_iif actually getting set.
Fixes: 1dfa76390bf05 ("net: ipv4: add check for l3slave for index returned in IP_PKTINFO")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geert Uytterhoeven [Wed, 13 Sep 2017 17:42:05 +0000 (19:42 +0200)]
net: smsc911x: Quieten netif during suspend
If the network interface is kept running during suspend, the net core
may call net_device_ops.ndo_start_xmit() while the Ethernet device is
still suspended, which may lead to a system crash.
E.g. on sh73a0/kzm9g and r8a73a4/ape6evm, the external Ethernet chip is
driven by a PM controlled clock. If the Ethernet registers are accessed
while the clock is not running, the system will crash with an imprecise
external abort.
As this is a race condition with a small time window, it is not so easy
to trigger at will. Using pm_test may increase your chances:
# echo 0 > /sys/module/printk/parameters/console_suspend
# echo platform > /sys/power/pm_test
# echo mem > /sys/power/state
To fix this, make sure the network interface is quietened during
suspend.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Tue, 12 Sep 2017 20:14:26 +0000 (13:14 -0700)]
net: systemport: Fix 64-bit stats deadlock
We can enter a deadlock situation because there is no sufficient protection
when ndo_get_stats64() runs in process context to guard against RX or TX NAPI
contexts running in softirq, this can lead to the following lockdep splat and
actual deadlock was experienced as well with an iperf session in the background
and a while loop doing ifconfig + ethtool.
[ 5.780350] ================================
[ 5.784679] WARNING: inconsistent lock state
[ 5.789011]
4.13.0-rc7-02179-g32fae27c725d #70 Not tainted
[ 5.794561] --------------------------------
[ 5.798890] inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
[ 5.804971] swapper/0/0 [HC0[0]:SC1[1]:HE0:SE0] takes:
[ 5.810175] (&syncp->seq#2){+.?...}, at: [<
c0768a28>] bcm_sysport_tx_reclaim+0x30/0x54
[ 5.818327] {SOFTIRQ-ON-W} state was registered at:
[ 5.823278] bcm_sysport_get_stats64+0x17c/0x258
[ 5.828053] dev_get_stats+0x38/0xac
[ 5.831776] rtnl_fill_stats+0x30/0x118
[ 5.835761] rtnl_fill_ifinfo+0x538/0xe24
[ 5.839921] rtmsg_ifinfo_build_skb+0x6c/0xd8
[ 5.844430] rtmsg_ifinfo_event.part.5+0x14/0x44
[ 5.849201] rtmsg_ifinfo+0x20/0x28
[ 5.852837] register_netdevice+0x628/0x6b8
[ 5.857171] register_netdev+0x14/0x24
[ 5.861051] bcm_sysport_probe+0x30c/0x438
[ 5.865280] platform_drv_probe+0x50/0xb0
[ 5.869418] driver_probe_device+0x2e8/0x450
[ 5.873817] __driver_attach+0x104/0x120
[ 5.877871] bus_for_each_dev+0x7c/0xc0
[ 5.881834] bus_add_driver+0x1b0/0x270
[ 5.885797] driver_register+0x78/0xf4
[ 5.889675] do_one_initcall+0x54/0x190
[ 5.893646] kernel_init_freeable+0x144/0x1d0
[ 5.898135] kernel_init+0x8/0x110
[ 5.901665] ret_from_fork+0x14/0x2c
[ 5.905363] irq event stamp: 24263
[ 5.908804] hardirqs last enabled at (24262): [<
c08eecf0>] net_rx_action+0xc4/0x4e4
[ 5.916624] hardirqs last disabled at (24263): [<
c0a7da00>] _raw_spin_lock_irqsave+0x1c/0x98
[ 5.925143] softirqs last enabled at (24258): [<
c022a7fc>] irq_enter+0x84/0x98
[ 5.932524] softirqs last disabled at (24259): [<
c022a918>] irq_exit+0x108/0x16c
[ 5.939985]
[ 5.939985] other info that might help us debug this:
[ 5.946576] Possible unsafe locking scenario:
[ 5.946576]
[ 5.952556] CPU0
[ 5.955031] ----
[ 5.957506] lock(&syncp->seq#2);
[ 5.960955] <Interrupt>
[ 5.963604] lock(&syncp->seq#2);
[ 5.967227]
[ 5.967227] *** DEADLOCK ***
[ 5.967227]
[ 5.973222] 1 lock held by swapper/0/0:
[ 5.977092] #0: (&(&ring->lock)->rlock){..-...}, at: [<
c0768a18>] bcm_sysport_tx_reclaim+0x20/0x54
So just remove the u64_stats_update_begin()/end() pair in ndo_get_stats64()
since it does not appear to be useful for anything. No inconsistency was
observed with either ifconfig or ethtool, global TX counts equal the sum of
per-queue TX counts on a 32-bit architecture.
Fixes: 10377ba7673d ("net: systemport: Support 64bit statistics")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Tue, 12 Sep 2017 20:10:53 +0000 (22:10 +0200)]
net: vrf: avoid gcc-4.6 warning
When building an allmodconfig kernel with gcc-4.6, we get a rather
odd warning:
drivers/net/vrf.c: In function ‘vrf_ip6_input_dst’:
drivers/net/vrf.c:964:3: error: initialized field with side-effects overwritten [-Werror]
drivers/net/vrf.c:964:3: error: (near initialization for ‘fl6’) [-Werror]
I have no idea what this warning is even trying to say, but it does
seem like a false positive. Reordering the initialization in to match
the structure definition gets rid of the warning, and might also avoid
whatever gcc thinks is wrong here.
Fixes: 9ff74384600a ("net: vrf: Handle ipv6 multicast and link-local addresses")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Himanshu Jha [Tue, 12 Sep 2017 11:19:22 +0000 (16:49 +0530)]
qed: remove unnecessary call to memset
call to memset to assign 0 value immediately after allocating
memory with kzalloc is unnecesaary as kzalloc allocates the memory
filled with 0 value.
Semantic patch used to resolve this issue:
@@
expression e,e2; constant c;
statement S;
@@
e = kzalloc(e2, c);
if(e == NULL) S
- memset(e, 0, e2);
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Acked-by: Sudarsana Kalluru <sudarsana.kalluru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 15 Sep 2017 19:58:55 +0000 (12:58 -0700)]
Merge tag 'firmware_removal-4.14-rc1' of git://git./linux/kernel/git/gregkh/driver-core
Pull firmware removal from Greg KH:
"Many many years ago (at the kernel summit in Boston), we all came to
the agreement that the firmware/ tree should be dropped from the
kernel, and everyone use the linux-firmware package instead. For some
minor reason, David Woodhouse didn't send the pull request at that
point in time, and everyone forgot about this.
The topic came up in the hallway track at the Plumbers conference this
week, so here's a single patch that drops the whole firmware tree. The
last firmware update was back in 2013, and all distros have been using
linux-firmware instead since at least that year, if not before. The
only commits to that directory since 2013 was some kbuild fixups for
various build tool issues.
So lets finally drop this, we don't need to lug them around in the
kernel source tree anymore, especially as no one wants or uses them.
This has passed build testing with 0-day, I don't think it made it
into linux-next this week, but I figured it was good to get in before
4.14-rc1 was out"
* tag 'firmware_removal-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
firmware: delete in-kernel firmware
Linus Torvalds [Fri, 15 Sep 2017 19:47:21 +0000 (12:47 -0700)]
Merge tag 'nios2-v4.14-rc1' of git://git./linux/kernel/git/lftan/nios2
Pull arch/nios2 update from Ley Foon Tan.
* tag 'nios2-v4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/lftan/nios2:
nios2: time: Read timer in get_cycles only if initialized
nios2: add earlycon support to 3c120 devboard DTS
Linus Torvalds [Fri, 15 Sep 2017 19:44:59 +0000 (12:44 -0700)]
Merge tag 'powerpc-4.14-2' of git://git./linux/kernel/git/powerpc/linux
Pull powerpc fix from Michael Ellerman:
"Just one fix, for the handling of alignment interrupts on dcbz
instructions.
Thanks to Paul Mackerras, Christian Zigotzky, Michal Sojka"
* tag 'powerpc-4.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc: Fix handling of alignment interrupt on dcbz instruction
Linus Torvalds [Fri, 15 Sep 2017 19:16:18 +0000 (12:16 -0700)]
Merge tag 'for-linus-4.14-ofs2' of git://git./linux/kernel/git/hubcap/linux
Pull orangefs updates from Mike Marshall:
"Some cleanups and a big bug fix for ACLs.
When I was reviewing Jan Kara's ACL patch, I realized that Orangefs
ACL code was busted, not just in the kernel module, but in the server
as well. I've been working on the code in the server mostly, but
here's one kernel patch, there will be more"
* tag 'for-linus-4.14-ofs2' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux:
orangefs: Adjust three checks for null pointers
orangefs: Use kcalloc() in orangefs_prepare_cdm_array()
orangefs: Delete error messages for a failed memory allocation in five functions
orangefs: constify xattr_handler structure
orangefs: don't call filemap_write_and_wait from fsync
orangefs: off by ones in xattr size checks
orangefs: documentation clean up
orangefs: react properly to posix_acl_update_mode's aftermath.
orangefs: Don't clear SGID when inheriting ACLs
Dmitry Torokhov [Fri, 15 Sep 2017 16:52:21 +0000 (09:52 -0700)]
Merge branch 'next' into for-linus
Prepare second round of input updates for 4.14 merge window.
Kai-Heng Feng [Fri, 15 Sep 2017 16:36:16 +0000 (09:36 -0700)]
Input: i8042 - add Gigabyte P57 to the keyboard reset table
Similar to other Gigabyte laptops, the touchpad on P57 requires a
keyboard reset to detect Elantech touchpad correctly.
BugLink: https://bugs.launchpad.net/bugs/1594214
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Jim Mattson [Thu, 14 Sep 2017 23:31:44 +0000 (16:31 -0700)]
kvm: nVMX: Handle deferred early VMLAUNCH/VMRESUME failure properly
When emulating a nested VM-entry from L1 to L2, several control field
validation checks are deferred to the hardware. Should one of these
validation checks fail, vcpu_vmx_run will set the vmx->fail flag. When
this happens, the L2 guest state is not loaded (even in part), and
execution should continue in L1 with the next instruction after the
VMLAUNCH/VMRESUME.
The VMCS12 is not modified (except for the VM-instruction error
field), the VMCS12 MSR save/load lists are not processed, and the CPU
state is not loaded from the VMCS12 host area. Moreover, the vmcs02
exit reason is stale, so it should not be consulted for any reason.
Signed-off-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Jim Mattson [Thu, 14 Sep 2017 23:31:42 +0000 (16:31 -0700)]
kvm: vmx: Handle VMLAUNCH/VMRESUME failure properly
On an early VMLAUNCH/VMRESUME failure (i.e. one which sets the
VM-instruction error field of the current VMCS), the launch state of
the current VMCS is not set to "launched," and the VM-exit information
fields of the current VMCS (including IDT-vectoring information and
exit reason) are stale.
On a late VMLAUNCH/VMRESUME failure (i.e. one which sets the high bit
of the exit reason field), the launch state of the current VMCS is not
set to "launched," and only two of the VM-exit information fields of
the current VMCS are modified (exit reason and exit
qualification). The remaining VM-exit information fields of the
current VMCS (including IDT-vectoring information, in particular) are
stale.
Signed-off-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Jim Mattson [Thu, 14 Sep 2017 23:31:40 +0000 (16:31 -0700)]
kvm: nVMX: Remove nested_vmx_succeed after successful VM-entry
After a successful VM-entry, RFLAGS is cleared, with the exception of
bit 1, which is always set. This is handled by load_vmcs12_host_state.
Signed-off-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Davidlohr Bueso [Wed, 13 Sep 2017 20:08:24 +0000 (13:08 -0700)]
kvm,mips: Fix potential swait_active() races
For example, the following could occur, making us miss a wakeup:
CPU0 CPU1
kvm_vcpu_block kvm_mips_comparecount_func
[L] swait_active(&vcpu->wq)
[S] prepare_to_swait(&vcpu->wq)
[L] if (!kvm_vcpu_has_pending_timer(vcpu))
schedule() [S] queue_timer_int(vcpu)
Ensure that the swait_active() check is not hoisted over the interrupt.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Davidlohr Bueso [Wed, 13 Sep 2017 20:08:23 +0000 (13:08 -0700)]
kvm,powerpc: Serialize wq active checks in ops->vcpu_kick
Particularly because kvmppc_fast_vcpu_kick_hv() is a callback,
ensure that we properly serialize wq active checks in order to
avoid potentially missing a wakeup due to racing with the waiter
side.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Davidlohr Bueso [Wed, 13 Sep 2017 20:08:22 +0000 (13:08 -0700)]
kvm: Serialize wq active checks in kvm_vcpu_wake_up()
This is a generic call and can be suceptible to races
in reading the wq task_list while another task is adding
itself to the list. Add a full barrier by using the
swq_has_sleeper() helper.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Davidlohr Bueso [Wed, 13 Sep 2017 20:08:21 +0000 (13:08 -0700)]
kvm,x86: Fix apf_task_wake_one() wq serialization
During code inspection, the following potential race was seen:
CPU0 CPU1
kvm_async_pf_task_wait apf_task_wake_one
[L] swait_active(&n->wq)
[S] prepare_to_swait(&n.wq)
[L] if (!hlist_unhahed(&n.link))
schedule() [S] hlist_del_init(&n->link);
Properly serialize swait_active() checks such that a wakeup is
not missed.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Davidlohr Bueso [Wed, 13 Sep 2017 20:08:20 +0000 (13:08 -0700)]
kvm,lapic: Justify use of swait_active()
A comment might serve future readers.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Davidlohr Bueso [Wed, 13 Sep 2017 20:08:19 +0000 (13:08 -0700)]
kvm,async_pf: Use swq_has_sleeper()
... as we've got the new helper now. This caller already
does the right thing, hence no changes in semantics.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Davidlohr Bueso [Wed, 13 Sep 2017 20:08:18 +0000 (13:08 -0700)]
sched/wait: Add swq_has_sleeper()
Which is the equivalent of what we have in regular waitqueues.
I'm not crazy about the name, but this also helps us get both
apis closer -- which iirc comes originally from the -net folks.
We also duplicate the comments for the lockless swait_active(),
from wait.h. Future users will make use of this interface.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Jan H. Schönherr [Thu, 7 Sep 2017 18:02:30 +0000 (19:02 +0100)]
KVM: VMX: Do not BUG() on out-of-bounds guest IRQ
The value of the guest_irq argument to vmx_update_pi_irte() is
ultimately coming from a KVM_IRQFD API call. Do not BUG() in
vmx_update_pi_irte() if the value is out-of bounds. (Especially,
since KVM as a whole seems to hang after that.)
Instead, print a message only once if we find that we don't have a
route for a certain IRQ (which can be out-of-bounds or within the
array).
This fixes CVE-2017-
1000252.
Fixes: efc644048ecde54 ("KVM: x86: Update IRTE for posted-interrupts")
Signed-off-by: Jan H. Schönherr <jschoenh@amazon.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Jan H. Schönherr [Thu, 7 Sep 2017 18:02:48 +0000 (19:02 +0100)]
KVM: Don't accept obviously wrong gsi values via KVM_IRQFD
We cannot add routes for gsi values >= KVM_MAX_IRQ_ROUTES -- see
kvm_set_irq_routing(). Hence, there is no sense in accepting them
via KVM_IRQFD. Prevent them from entering the system in the first
place.
Signed-off-by: Jan H. Schönherr <jschoenh@amazon.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Guenter Roeck [Tue, 12 Sep 2017 03:45:26 +0000 (20:45 -0700)]
nios2: time: Read timer in get_cycles only if initialized
Mainline crashes as follows when running nios2 images.
On node 0 totalpages: 65536
free_area_init_node: node 0, pgdat
c8408fa0, node_mem_map
c8726000
Normal zone: 512 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 65536 pages, LIFO batch:15
Unable to handle kernel NULL pointer dereference at virtual address
00000000
ea =
c8003cb0, ra =
c81cbf40, cause = 15
Kernel panic - not syncing: Oops
Problem is seen because get_cycles() is called before the timer it depends
on is initialized. Returning 0 in that situation fixes the problem.
Fixes: 33d72f3822d7 ("init/main.c: extract early boot entropy from the ..")
Cc: Laura Abbott <labbott@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Daniel Micay <danielmicay@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tobias Klauser [Tue, 20 Jun 2017 07:43:18 +0000 (09:43 +0200)]
nios2: add earlycon support to 3c120 devboard DTS
Allow earlycon to be used on the JTAG UART present in the 3c120 GHRD.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Jim Mattson [Tue, 12 Sep 2017 20:02:54 +0000 (13:02 -0700)]
kvm: nVMX: Don't allow L2 to access the hardware CR8
If L1 does not specify the "use TPR shadow" VM-execution control in
vmcs12, then L0 must specify the "CR8-load exiting" and "CR8-store
exiting" VM-execution controls in vmcs02. Failure to do so will give
the L2 VM unrestricted read/write access to the hardware CR8.
This fixes CVE-2017-12154.
Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Bjorn Helgaas [Fri, 15 Sep 2017 06:33:51 +0000 (01:33 -0500)]
Revert "PCI: Avoid race while enabling upstream bridges"
This reverts commit
40f11adc7cd9281227f0a6a627d966dd0a5f0cd9.
Jens found that iwlwifi firmware loading failed on a Lenovo X1 Carbon,
gen4:
iwlwifi 0000:04:00.0: Direct firmware load for iwlwifi-8000C-34.ucode failed with error -2
iwlwifi 0000:04:00.0: Direct firmware load for iwlwifi-8000C-33.ucode failed with error -2
iwlwifi 0000:04:00.0: Direct firmware load for iwlwifi-8000C-32.ucode failed with error -2
iwlwifi 0000:04:00.0: loaded firmware version 31.532993.0 op_mode iwlmvm
iwlwifi 0000:04:00.0: Detected Intel(R) Dual Band Wireless AC 8260, REV=0x208
...
iwlwifi 0000:04:00.0: Failed to load firmware chunk!
iwlwifi 0000:04:00.0: Could not load the [0] uCode section
iwlwifi 0000:04:00.0: Failed to start INIT ucode: -110
iwlwifi 0000:04:00.0: Failed to run INIT ucode: -110
He bisected it to
40f11adc7cd9 ("PCI: Avoid race while enabling upstream
bridges"). Revert that commit to fix the regression.
Link: http://lkml.kernel.org/r/4bcbcbc1-7c79-09f0-5071-bc2f53bf6574@kernel.dk
Fixes: 40f11adc7cd9 ("PCI: Avoid race while enabling upstream bridges")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Srinath Mannam <srinath.mannam@broadcom.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: Luca Coelho <luca@coelho.fi>
CC: Johannes Berg <johannes@sipsolutions.net>
CC: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Mimi Zohar [Wed, 13 Sep 2017 02:45:33 +0000 (22:45 -0400)]
vfs: constify path argument to kernel_read_file_from_path
This patch constifies the path argument to kernel_read_file_from_path().
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 15 Sep 2017 03:04:32 +0000 (20:04 -0700)]
Merge tag 'nfs-for-4.14-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull more NFS client updates from Trond Myklebust:
"Hightlights include:
Bugfixes:
- Various changes relating to reporting IO errors.
- pnfs: Use the standard I/O stateid when calling LAYOUTGET
Features:
- Add static NFS I/O tracepoints for debugging"
* tag 'nfs-for-4.14-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS: various changes relating to reporting IO errors.
NFS: Add static NFS I/O tracepoints
pNFS: Use the standard I/O stateid when calling LAYOUTGET
Linus Torvalds [Fri, 15 Sep 2017 03:01:41 +0000 (20:01 -0700)]
Merge branch 'work.misc' of git://git./linux/kernel/git/viro/vfs
Pull misc leftovers from Al Viro.
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fix the __user misannotations in asm-generic get_user/put_user
fput: Don't reinvent the wheel but use existing llist API
namespace.c: Don't reinvent the wheel but use existing llist API
Linus Torvalds [Fri, 15 Sep 2017 02:29:55 +0000 (19:29 -0700)]
Merge branch 'work.read_write' of git://git./linux/kernel/git/viro/vfs
Pull nowait read support from Al Viro:
"Support IOCB_NOWAIT for buffered reads and block devices"
* 'work.read_write' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
block_dev: support RFW_NOWAIT on block device nodes
fs: support RWF_NOWAIT for buffered reads
fs: support IOCB_NOWAIT in generic_file_buffered_read
fs: pass iocb to do_generic_file_read
Linus Torvalds [Fri, 15 Sep 2017 01:54:01 +0000 (18:54 -0700)]
Merge branch 'work.mount' of git://git./linux/kernel/git/viro/vfs
Pull mount flag updates from Al Viro:
"Another chunk of fmount preparations from dhowells; only trivial
conflicts for that part. It separates MS_... bits (very grotty
mount(2) ABI) from the struct super_block ->s_flags (kernel-internal,
only a small subset of MS_... stuff).
This does *not* convert the filesystems to new constants; only the
infrastructure is done here. The next step in that series is where the
conflicts would be; that's the conversion of filesystems. It's purely
mechanical and it's better done after the merge, so if you could run
something like
list=$(for i in MS_RDONLY MS_NOSUID MS_NODEV MS_NOEXEC MS_SYNCHRONOUS MS_MANDLOCK MS_DIRSYNC MS_NOATIME MS_NODIRATIME MS_SILENT MS_POSIXACL MS_KERNMOUNT MS_I_VERSION MS_LAZYTIME; do git grep -l $i fs drivers/staging/lustre drivers/mtd ipc mm include/linux; done|sort|uniq|grep -v '^fs/namespace.c$')
sed -i -e 's/\<MS_RDONLY\>/SB_RDONLY/g' \
-e 's/\<MS_NOSUID\>/SB_NOSUID/g' \
-e 's/\<MS_NODEV\>/SB_NODEV/g' \
-e 's/\<MS_NOEXEC\>/SB_NOEXEC/g' \
-e 's/\<MS_SYNCHRONOUS\>/SB_SYNCHRONOUS/g' \
-e 's/\<MS_MANDLOCK\>/SB_MANDLOCK/g' \
-e 's/\<MS_DIRSYNC\>/SB_DIRSYNC/g' \
-e 's/\<MS_NOATIME\>/SB_NOATIME/g' \
-e 's/\<MS_NODIRATIME\>/SB_NODIRATIME/g' \
-e 's/\<MS_SILENT\>/SB_SILENT/g' \
-e 's/\<MS_POSIXACL\>/SB_POSIXACL/g' \
-e 's/\<MS_KERNMOUNT\>/SB_KERNMOUNT/g' \
-e 's/\<MS_I_VERSION\>/SB_I_VERSION/g' \
-e 's/\<MS_LAZYTIME\>/SB_LAZYTIME/g' \
$list
and commit it with something along the lines of 'convert filesystems
away from use of MS_... constants' as commit message, it would save a
quite a bit of headache next cycle"
* 'work.mount' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
VFS: Differentiate mount flags (MS_*) from internal superblock flags
VFS: Convert sb->s_flags & MS_RDONLY to sb_rdonly(sb)
vfs: Add sb_rdonly(sb) to query the MS_RDONLY flag on s_flags
Linus Torvalds [Fri, 15 Sep 2017 01:13:32 +0000 (18:13 -0700)]
Merge branch 'work.set_fs' of git://git./linux/kernel/git/viro/vfs
Pull more set_fs removal from Al Viro:
"Christoph's 'use kernel_read and friends rather than open-coding
set_fs()' series"
* 'work.set_fs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: unexport vfs_readv and vfs_writev
fs: unexport vfs_read and vfs_write
fs: unexport __vfs_read/__vfs_write
lustre: switch to kernel_write
gadget/f_mass_storage: stop messing with the address limit
mconsole: switch to kernel_read
btrfs: switch write_buf to kernel_write
net/9p: switch p9_fd_read to kernel_write
mm/nommu: switch do_mmap_private to kernel_read
serial2002: switch serial2002_tty_write to kernel_{read/write}
fs: make the buf argument to __kernel_write a void pointer
fs: fix kernel_write prototype
fs: fix kernel_read prototype
fs: move kernel_read to fs/read_write.c
fs: move kernel_write to fs/read_write.c
autofs4: switch autofs4_write to __kernel_write
ashmem: switch to ->read_iter
Linus Torvalds [Fri, 15 Sep 2017 00:37:26 +0000 (17:37 -0700)]
Merge branch 'work.ipc' of git://git./linux/kernel/git/viro/vfs
Pull ipc compat cleanup and 64-bit time_t from Al Viro:
"IPC copyin/copyout sanitizing, including 64bit time_t work from Deepa
Dinamani"
* 'work.ipc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
utimes: Make utimes y2038 safe
ipc: shm: Make shmid_kernel timestamps y2038 safe
ipc: sem: Make sem_array timestamps y2038 safe
ipc: msg: Make msg_queue timestamps y2038 safe
ipc: mqueue: Replace timespec with timespec64
ipc: Make sys_semtimedop() y2038 safe
get rid of SYSVIPC_COMPAT on ia64
semtimedop(): move compat to native
shmat(2): move compat to native
msgrcv(2), msgsnd(2): move compat to native
ipc(2): move compat to native
ipc: make use of compat ipc_perm helpers
semctl(): move compat to native
semctl(): separate all layout-dependent copyin/copyout
msgctl(): move compat to native
msgctl(): split the actual work from copyin/copyout
ipc: move compat shmctl to native
shmctl: split the work from copyin/copyout
Linus Torvalds [Fri, 15 Sep 2017 00:30:49 +0000 (17:30 -0700)]
Merge branch 'zstd-minimal' of git://git./linux/kernel/git/mason/linux-btrfs
Pull zstd support from Chris Mason:
"Nick Terrell's patch series to add zstd support to the kernel has been
floating around for a while. After talking with Dave Sterba, Herbert
and Phillip, we decided to send the whole thing in as one pull
request.
zstd is a big win in speed over zlib and in compression ratio over
lzo, and the compression team here at FB has gotten great results
using it in production. Nick will continue to update the kernel side
with new improvements from the open source zstd userland code.
Nick has a number of benchmarks for the main zstd code in his lib/zstd
commit:
I ran the benchmarks on a Ubuntu 14.04 VM with 2 cores and 4 GiB
of RAM. The VM is running on a MacBook Pro with a 3.1 GHz Intel
Core i7 processor, 16 GB of RAM, and a SSD. I benchmarked using
`silesia.tar` [3], which is 211,988,480 B large. Run the following
commands for the benchmark:
sudo modprobe zstd_compress_test
sudo mknod zstd_compress_test c 245 0
sudo cp silesia.tar zstd_compress_test
The time is reported by the time of the userland `cp`.
The MB/s is computed with
1,536,217,008 B / time(buffer size, hash)
which includes the time to copy from userland.
The Adjusted MB/s is computed with
1,536,217,088 B / (time(buffer size, hash) - time(buffer size, none)).
The memory reported is the amount of memory the compressor
requests.
| Method | Size (B) | Time (s) | Ratio | MB/s | Adj MB/s | Mem (MB) |
|----------|----------|----------|-------|---------|----------|----------|
| none |
11988480 | 0.100 | 1 | 2119.88 | - | - |
| zstd -1 |
73645762 | 1.044 | 2.878 | 203.05 | 224.56 | 1.23 |
| zstd -3 |
66988878 | 1.761 | 3.165 | 120.38 | 127.63 | 2.47 |
| zstd -5 |
65001259 | 2.563 | 3.261 | 82.71 | 86.07 | 2.86 |
| zstd -10 |
60165346 | 13.242 | 3.523 | 16.01 | 16.13 | 13.22 |
| zstd -15 |
58009756 | 47.601 | 3.654 | 4.45 | 4.46 | 21.61 |
| zstd -19 |
54014593 | 102.835 | 3.925 | 2.06 | 2.06 | 60.15 |
| zlib -1 |
77260026 | 2.895 | 2.744 | 73.23 | 75.85 | 0.27 |
| zlib -3 |
72972206 | 4.116 | 2.905 | 51.50 | 52.79 | 0.27 |
| zlib -6 |
68190360 | 9.633 | 3.109 | 22.01 | 22.24 | 0.27 |
| zlib -9 |
67613382 | 22.554 | 3.135 | 9.40 | 9.44 | 0.27 |
I benchmarked zstd decompression using the same method on the same
machine. The benchmark file is located in the upstream zstd repo
under `contrib/linux-kernel/zstd_decompress_test.c` [4]. The
memory reported is the amount of memory required to decompress
data compressed with the given compression level. If you know the
maximum size of your input, you can reduce the memory usage of
decompression irrespective of the compression level.
| Method | Time (s) | MB/s | Adjusted MB/s | Memory (MB) |
|----------|----------|---------|---------------|-------------|
| none | 0.025 | 8479.54 | - | - |
| zstd -1 | 0.358 | 592.15 | 636.60 | 0.84 |
| zstd -3 | 0.396 | 535.32 | 571.40 | 1.46 |
| zstd -5 | 0.396 | 535.32 | 571.40 | 1.46 |
| zstd -10 | 0.374 | 566.81 | 607.42 | 2.51 |
| zstd -15 | 0.379 | 559.34 | 598.84 | 4.61 |
| zstd -19 | 0.412 | 514.54 | 547.77 | 8.80 |
| zlib -1 | 0.940 | 225.52 | 231.68 | 0.04 |
| zlib -3 | 0.883 | 240.08 | 247.07 | 0.04 |
| zlib -6 | 0.844 | 251.17 | 258.84 | 0.04 |
| zlib -9 | 0.837 | 253.27 | 287.64 | 0.04 |
I ran a long series of tests and benchmarks on the btrfs side and the
gains are very similar to the core benchmarks Nick ran"
* 'zstd-minimal' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
squashfs: Add zstd support
btrfs: Add zstd support
lib: Add zstd modules
lib: Add xxhash module
Paul Mackerras [Wed, 13 Sep 2017 04:51:24 +0000 (14:51 +1000)]
powerpc: Fix handling of alignment interrupt on dcbz instruction
This fixes the emulation of the dcbz instruction in the alignment
interrupt handler. The error was that we were comparing just the
instruction type field of op.type rather than the whole thing,
and therefore the comparison "type != CACHEOP + DCBZ" was always
true.
Fixes: 31bfdb036f12 ("powerpc: Use instruction emulation infrastructure to handle alignment faults")
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Tested-by: Michal Sojka <sojkam1@fel.cvut.cz>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Greg Kroah-Hartman [Thu, 14 Sep 2017 21:23:01 +0000 (14:23 -0700)]
firmware: delete in-kernel firmware
The last firmware change for the in-kernel firmware source code was back
in 2013. Everyone has been relying on the out-of-tree linux-firmware
package for a long long time.
So let's drop it, it's baggage we don't need to keep dragging around
(and having to fix random kbuild issues over time...)
Cc: Kyle McMartin <kyle@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Michal Marek <mmarek@suse.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Thu, 14 Sep 2017 20:46:33 +0000 (13:46 -0700)]
Merge tag 'kbuild-v4.14' of git://git./linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- Use Make-builtin $(abspath ...) helper to get absolute path
- Add W=2 extra warning option to detect unused macros
- Use more KCONFIG_CONFIG instead hard-coded .config
- Fix bugs of tar*-pkg targets
* tag 'kbuild-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: buildtar: do not print successful message if tar returns error
kbuild: buildtar: fix tar error when CONFIG_MODULES is disabled
kbuild: Use KCONFIG_CONFIG in buildtar
Kbuild: enable -Wunused-macros warning for "make W=2"
kbuild: use $(abspath ...) instead of $(shell cd ... && /bin/pwd)
Linus Torvalds [Thu, 14 Sep 2017 20:43:16 +0000 (13:43 -0700)]
Merge tag 'for-4.14/dm-changes' of git://git./linux/kernel/git/device-mapper/linux-dm
Pull device mapper updates from Mike Snitzer:
- Some request-based DM core and DM multipath fixes and cleanups
- Constify a few variables in DM core and DM integrity
- Add bufio optimization and checksum failure accounting to DM
integrity
- Fix DM integrity to avoid checking integrity of failed reads
- Fix DM integrity to use init_completion
- A couple DM log-writes target fixes
- Simplify DAX flushing by eliminating the unnecessary flush
abstraction that was stood up for DM's use.
* tag 'for-4.14/dm-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dax: remove the pmem_dax_ops->flush abstraction
dm integrity: use init_completion instead of COMPLETION_INITIALIZER_ONSTACK
dm integrity: make blk_integrity_profile structure const
dm integrity: do not check integrity for failed read operations
dm log writes: fix >512b sectorsize support
dm log writes: don't use all the cpu while waiting to log blocks
dm ioctl: constify ioctl lookup table
dm: constify argument arrays
dm integrity: count and display checksum failures
dm integrity: optimize writing dm-bufio buffers that are partially changed
dm rq: do not update rq partially in each ending bio
dm rq: make dm-sq requeuing behavior consistent with dm-mq behavior
dm mpath: complain about unsupported __multipath_map_bio() return values
dm mpath: avoid that building with W=1 causes gcc 7 to complain about fall-through
Linus Torvalds [Thu, 14 Sep 2017 20:33:33 +0000 (13:33 -0700)]
Merge tag 'fbdev-v4.14' of git://github.com/bzolnier/linux
Pull fbdev updates from Bartlomiej Zolnierkiewicz:
- make fbcon a built-time depency for fbdev (fbcon was tristate option
before, now it is a bool) - this is a first step in preparations for
making console_lock usage saner (currently it acts like the BKL for
all things fbdev/fbcon) (Daniel Vetter)
- add fbcon=margin:<color> command line option to select the fbcon
margin color (David Lechner)
- add DMI quirk table for x86 systems which need fbcon rotation
(devices like Asus T100HA, GPD Pocket, the GPD win and the I.T.Works
TW891) (Hans de Goede)
- fix 1bpp logo support for unusual width (needed by LEGO MINDSTORMS
EV3) (David Lechner)
- enable Xilinx FB driver for ARM ZynqMP platform (Michal Simek)
- fix use after free in the error path of udlfb driver (Anton Vasilyev)
- fix error return code handling in pxa3xx_gcu driver (Gustavo A. R.
Silva)
- fix bootparams.screeninfo arguments checking in vgacon (Jan H.
Schönherr)
- do not leak uninitialized padding in clk to userspace in the debug
code of atyfb driver (Vladis Dronov)
- fix compiler warnings in fbcon code and matroxfb driver (Arnd
Bergmann)
- convert fbdev susbsytem to using %pOF instead of full_name (Rob
Herring)
- structures constifications (Arvind Yadav, Bhumika Goyal, Gustavo A.
R. Silva, Julia Lawall)
- misc cleanups (Gustavo A. R. Silva, Hyun Kwon, Julia Lawall, Kuninori
Morimoto, Lynn Lei)
* tag 'fbdev-v4.14' of git://github.com/bzolnier/linux: (75 commits)
video/console: Update BIOS dates list for GPD win console rotation DMI quirk
video/console: Add rotated LCD-panel DMI quirk for the VIOS LTH17
video: fbdev: sis: fix duplicated code for different branches
video: fbdev: make fb_var_screeninfo const
video: fbdev: aty: do not leak uninitialized padding in clk to userspace
vgacon: Prevent faulty bootparams.screeninfo from causing harm
video: fbdev: make fb_videomode const
video/console: Add new BIOS date for GPD pocket to dmi quirk table
fbcon: remove restriction on margin color
video: ARM CLCD: constify amba_id
video: fm2fb: constify zorro_device_id
video: fbdev: annotate fb_fix_screeninfo with const and __initconst
omapfb: constify omap_video_timings structures
video: fbdev: udlfb: Fix use after free on dlfb_usb_probe error path
fbdev: i810: make fb_ops const
fbdev: matrox: make fb_ops const
video: fbdev: pxa3xx_gcu: fix error return code in pxa3xx_gcu_probe()
video: fbdev: Enable Xilinx FB for ZynqMP
video: fbdev: Fix multiple style issues in xilinxfb
video: fbdev: udlfb: constify usb_device_id.
...
Linus Torvalds [Thu, 14 Sep 2017 20:28:30 +0000 (13:28 -0700)]
Merge git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- add support for the watchdog on Meson8 and Meson8m2
- add support for MediaTek MT7623 and MT7622 SoC
- add support for the r8a77995 wdt
- explicitly request exclusive reset control for asm9260_wdt,
zx2967_wdt, rt2880_wdt and mt7621_wdt
- improvements to asm9260_wdt, aspeed_wdt, renesas_wdt and cadence_wdt
- add support for reading freq via CCF + suspend/resume support for
of_xilinx_wdt
- constify watchdog_ops and various device-id structures
- revert of commit
1fccb73011ea ("iTCO_wdt: all versions count down
twice") (Bug 196509)
* git://www.linux-watchdog.org/linux-watchdog: (40 commits)
watchdog: mei_wdt: constify mei_cl_device_id
watchdog: sp805: constify amba_id
watchdog: ziirave: constify i2c_device_id
watchdog: sc1200: constify pnp_device_id
dt-bindings: watchdog: renesas-wdt: Add support for the r8a77995 wdt
watchdog: renesas_wdt: update copyright dates
watchdog: renesas_wdt: make 'clk' a variable local to probe()
watchdog: renesas_wdt: consistently use RuntimePM for clock management
watchdog: aspeed: Support configuration of external signal properties
dt-bindings: watchdog: aspeed: External reset signal properties
drivers/watchdog: Add optional ASPEED device tree properties
drivers/watchdog: ASPEED reference dev tree properties for config
watchdog: da9063_wdt: Simplify by removing unneeded struct...
watchdog: bcm7038: Check the return value from clk_prepare_enable()
watchdog: qcom: Check for platform_get_resource() failure
watchdog: of_xilinx_wdt: Add suspend/resume support
watchdog: of_xilinx_wdt: Add support for reading freq via CCF
dt-bindings: watchdog: mediatek: add support for MediaTek MT7623 and MT7622 SoC
watchdog: max77620_wdt: constify platform_device_id
watchdog: pcwd_usb: constify usb_device_id
...
Linus Torvalds [Thu, 14 Sep 2017 20:10:48 +0000 (13:10 -0700)]
Merge branch 'dmi-for-linus' of git://git./linux/kernel/git/jdelvare/staging
Pull dmi update from Jean Delvare:
"Mark all struct dmi_system_id instances const"
* 'dmi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
dmi: Mark all struct dmi_system_id instances const
Linus Torvalds [Thu, 14 Sep 2017 20:01:09 +0000 (13:01 -0700)]
Merge tag 'pinctrl-v4.14-2' of git://git./linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"This slew of fixes for pin control was noticed and patched up early,
so to get the annoyance out of the way for -rc1 it would make sense to
send them already.
- Fix a build include in the Uniphier driver to keep pace with
ongoing refactorings.
- Fix a slew of minor semantic and syntactic issues as well as
stricting up Kconfig for the new Spreadtrum driver.
- Fix the GPIO interrupt set-up on the Marvell 37xx Armada as fallout
for dynamically allocating irq descriptors from the core. (Also
tagged for stable.)
- Fix AMD register suspend/resume state spool/unspooling so that
wakeup works as it should. (Also tagged for stable.)"
* tag 'pinctrl-v4.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl/amd: save pin registers over suspend/resume
pinctrl: armada-37xx: Fix gpio interrupt setup
pinctrl: sprd: fix off by one bugs
pinctrl: sprd: check for allocation failure
pinctrl: sprd: Restrict PINCTRL_SPRD to ARCH_SPRD or COMPILE_TEST
pinctrl: sprd: fix build errors and dependencies
pinctrl: sprd: make three local functions static
pinctrl: uniphier: include <linux/build_bug.h> instead of <linux/bug.h>
Linus Torvalds [Thu, 14 Sep 2017 19:25:34 +0000 (12:25 -0700)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"A few leftovers"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm, page_owner: skip unnecessary stack_trace entries
arm64: stacktrace: avoid listing stacktrace functions in stacktrace
mm: treewide: remove GFP_TEMPORARY allocation flag
IB/mlx4: fix sprintf format warning
fscache: fix fscache_objlist_show format processing
lib/test_bitmap.c: use ULL suffix for 64-bit constants
procfs: remove unused variable
drivers/media/cec/cec-adap.c: fix build with gcc-4.4.4
idr: remove WARN_ON_ONCE() when trying to replace negative ID
projects / openwrt / staging / blogic.git / log