Rui Salvaterra [Wed, 8 May 2024 21:04:55 +0000 (22:04 +0100)]
linux-firmware: realtek: update rtl8821ae firmware
A newer version, rtl8821aefw_29.bin, has been available for over 7 years [1].
Let's use it.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit?id=
f70e4df2b384d21e36a7c30a591639592692e0ec
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
(cherry picked from commit
2b8e875a85802f6281df134e2231308f6c928796)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Sahil Dhiman [Sat, 25 May 2024 09:57:12 +0000 (15:27 +0530)]
scripts: Add GNU ftp mirror redirector for GNU and Savannah
Add GNU's redirector which automatically redirect user to nearby online
mirror.
Signed-off-by: Sahil Dhiman <sahil@hopbox.in>
Link: https://github.com/openwrt/openwrt/pull/15557
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit
6510eb3b5d612ea7a70c4a8d9b83639e3b46e221)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Fri, 31 May 2024 12:39:51 +0000 (14:39 +0200)]
tegra: Activate CONFIG_SND_DRIVERS
The option CONFIG_SND_DRIVERS is activated by default in the generic
configuration, do not deactivate it for tegra. This fixes the build of
the kmod-sound-dummy package on tegra.
(cherry picked from commit
21213c8156ccca90c135910b2ae2cdf40b8d98c3)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Qingfang Deng [Fri, 7 Jun 2024 09:55:38 +0000 (17:55 +0800)]
config: kernel: remove KASAN_EXTRA
The option has been removed from the kernel since 5.1.
Signed-off-by: Qingfang Deng <dqfext@gmail.com>
(cherry picked from commit
60ea3d6d46954553b7b50460dfe6b86878fe5990)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Daniel Golle [Mon, 10 Jun 2024 22:39:36 +0000 (23:39 +0100)]
mt76: mt7996: select required kernel and hostap options
Select DRIVER_11AX_SUPPORT and KERNEL_RELAY also for kmod-mt7996 to
prevent build failure if only this driver is selected during build and
end up with (most) required hostap features (IEEE 802.11be rates are not
yet supported).
Reported-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit
83311b747012e0675f96af18793e92cb8320c707)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Christian Lamparter [Sun, 2 Jun 2024 13:54:14 +0000 (15:54 +0200)]
firmware: intel-microcode: update to
20240531
Debian changelog:
intel-microcode (3.
20240531.1) unstable; urgency=medium
* New upstream microcode datafile
20240531
* Fix unspecified functional issues on Pentium Silver N/J5xxx,
Celeron N/J4xxx
* Updated Microcodes:
sig 0x000706a1, pf_mask 0x01, 2024-04-19, rev 0x0042, size 76800
* source: update symlinks to reflect id of the latest release,
20240531
-- Henrique de Moraes Holschuh <hmh@debian.org> Sat, 01 Jun 2024 11:49:47 -0300
intel-microcode (3.
20240514.1) unstable; urgency=medium
* New upstream microcode datafile
20240514
* Mitigations for INTEL-SA-01051 (CVE-2023-45733)
Hardware logic contains race conditions in some Intel Processors may
allow an authenticated user to potentially enable partial information
disclosure via local access.
* Mitigations for INTEL-SA-01052 (CVE-2023-46103)
Sequence of processor instructions leads to unexpected behavior in
Intel Core Ultra Processors may allow an authenticated user to
potentially enable denial of service via local access.
* Mitigations for INTEL-SA-01036 (CVE-2023-45745, CVE-2023-47855)
Improper input validation in some Intel TDX module software before
version 1.5.05.46.698 may allow a privileged user to potentially enable
escalation of privilege via local access.
* Fix for unspecified functional issues on 4th gen and 5th gen Xeon
Scalable, 12th, 13th and 14th gen Intel Core processors, as well as for
Core i3 N-series processors.
* Updated microcodes:
sig 0x000806f8, pf_mask 0x87, 2024-02-05, rev 0x2b0005c0, size 581632
sig 0x000806f7, pf_mask 0x87, 2024-02-05, rev 0x2b0005c0
sig 0x000806f6, pf_mask 0x87, 2024-02-05, rev 0x2b0005c0
sig 0x000806f5, pf_mask 0x87, 2024-02-05, rev 0x2b0005c0
sig 0x000806f4, pf_mask 0x87, 2024-02-05, rev 0x2b0005c0
sig 0x000806f8, pf_mask 0x10, 2024-02-05, rev 0x2c000390, size 614400
sig 0x000806f6, pf_mask 0x10, 2024-02-05, rev 0x2c000390
sig 0x000806f5, pf_mask 0x10, 2024-02-05, rev 0x2c000390
sig 0x000806f4, pf_mask 0x10, 2024-02-05, rev 0x2c000390
sig 0x00090672, pf_mask 0x07, 2023-12-05, rev 0x0035, size 224256
sig 0x00090675, pf_mask 0x07, 2023-12-05, rev 0x0035
sig 0x000b06f2, pf_mask 0x07, 2023-12-05, rev 0x0035
sig 0x000b06f5, pf_mask 0x07, 2023-12-05, rev 0x0035
sig 0x000906a3, pf_mask 0x80, 2023-12-05, rev 0x0433, size 222208
sig 0x000906a4, pf_mask 0x80, 2023-12-05, rev 0x0433
sig 0x000906a4, pf_mask 0x40, 2023-12-07, rev 0x0007, size 119808
sig 0x000b0671, pf_mask 0x32, 2024-01-25, rev 0x0123, size 215040
sig 0x000b06e0, pf_mask 0x11, 2023-12-07, rev 0x0017, size 138240
sig 0x000c06f2, pf_mask 0x87, 2024-02-05, rev 0x21000230, size 552960
sig 0x000c06f1, pf_mask 0x87, 2024-02-05, rev 0x21000230
* source: update symlinks to reflect id of the latest release,
20240514
-- Henrique de Moraes Holschuh <hmh@debian.org> Thu, 16 May 2024 21:40:52 -0300
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit
7d9b9762c95f5630857d8b08567fc1d72eb23217)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rosen Penev [Fri, 14 Jun 2024 23:01:34 +0000 (16:01 -0700)]
tools/sparse: fix compilation with GCC14
Upstream backport.
Get rid of PKG_RELEASE as it's irrelevant to tools.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
(cherry picked from commit
253d777c968b8fd74e857bec4cd74267daae0010)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Christian Marangi [Mon, 17 Jun 2024 11:19:52 +0000 (13:19 +0200)]
scripts/ext-toolchain: add missing libc library specs
Add missing libc library spec that weren't added to the ext-toolchain
script when the library were introduced in the packages libs toolchain
Makefile.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit
8cad52a267bffe384a119f3e5ae1892e8580a981)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Felix Fietkau [Fri, 14 Jun 2024 12:43:39 +0000 (14:43 +0200)]
hostapd: fix crash on interface setup failure
Add a missing NULL pointer check when deleting beacons
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit
3984fb0582083c5c0f511ed3a33eb17908eccb08)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Felix Fietkau [Fri, 14 Jun 2024 12:17:57 +0000 (14:17 +0200)]
hostapd: use strdup on string passed to hostapd_add_iface
The data is modified within hostapd_add_iface
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit
032d3fcf7a861b140435b6507b2b0b66361c92f8)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Nathaniel Wesley Filardo [Thu, 20 Jun 2024 14:15:50 +0000 (15:15 +0100)]
kernel: crypto: remove FCRYPT from miscellany
It has its own dedicated knob
Signed-off-by: Nathaniel Wesley Filardo <nwfilardo@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15761
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit
7d71c03ab188a58d74d6cdbeabb38b70ead2c74b)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 29 Jun 2024 16:23:13 +0000 (18:23 +0200)]
kernel: Add kmod-mfd
Package the mfd-core.ko kernel module. It is selected by the
kmod-hwmon-gsc already.
Link: https://github.com/openwrt/openwrt/pull/15833
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit
8b4fd1c0dece936dc2c79f2a17d824512e7e7df3)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 29 Jun 2024 16:14:47 +0000 (18:14 +0200)]
kernel: Add kmod-crypto-xxhash
kxxhash_generic.ko is a soft dependency of kmod-fs-btrfs, but we did not
package it. Extract the kmod-lib-xxhash and then package
xxhash_generic.ko.
Link: https://github.com/openwrt/openwrt/pull/15833
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit
2ebeda029490e308cc0e8f475e63280f960e74c4)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 29 Jun 2024 15:38:46 +0000 (17:38 +0200)]
kernel: Add kmod-crypto-blake2b
The kmod-fs-btrfs package has a soft dependency to kmod-crypto-blake2b
The CONFIG_BTRFS_FS kernel build option selects CONFIG_CRYPTO_BLAKE2B,
but we did not package it before.
Link: https://github.com/openwrt/openwrt/pull/15833
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit
f89091bba6be483e66c5ac14c477621f74aef203)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 29 Jun 2024 15:54:49 +0000 (17:54 +0200)]
kernel: Fix kmod-lib-lz4 packaging
The kernel provides two variants of the lz4 compression a normal version
and a high compression mode version. The old kmod-lib-lz4 package
contained the normal version plus one part of the lz4hc version. There
was already code which selected the kmod-lib-lz4hc package which did
not exists.
I split this into 3 packages. kmod-lib-lz4 and kmod-lib-lz4hc for the
normal the and high compression algorithm which contain the specific
code and the kmod-lib-lz4-decompress which contains the common
decompressor.
New we are also packaging lz4hc.ko
Link: https://github.com/openwrt/openwrt/pull/15833
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit
fac507606d75eec04762013582273468eea7ed92)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 29 Jun 2024 15:24:09 +0000 (17:24 +0200)]
kernel: Extract kmod-nf-dup-inet
The nf_dup_ipv4.ko and nf_dup_ipv6.ko kernel module were packaged by
kmod-ipt-tee and kmod-nft-dup-inet at the same time. Extract them into a
separate package used by both.
Link: https://github.com/openwrt/openwrt/pull/15833
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit
b0953c4fbf1bb0ad0844febe991636d05884c194)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Paweł Owoc [Mon, 18 Mar 2024 20:53:51 +0000 (21:53 +0100)]
mac80211: add missing config for third 160MHz width for 5GHz radio
Without this configuration it is not possible to run the radio using HE160 on channels 149-177.
Fixes: #14906
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
(cherry picked from commit
a91b79fd04d58e711273d08e0b1246942b2eec98)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Felix Fietkau [Tue, 11 Jul 2023 12:38:06 +0000 (14:38 +0200)]
mac80211: add fix for receiving STP frames on mesh
Fix length in ethernet header
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit
8f7be2a2ba79987bd150f5f4e266daf96fd94e32)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Oldřich Jedlička [Fri, 6 Oct 2023 21:37:47 +0000 (23:37 +0200)]
mac80211: fix flush during station removal
This fixes WARN_ONs when using AP_VLANs after station removal. The flush
call passed AP_VLAN vif to driver, but because these vifs are virtual and
not registered with drivers, we need to translate to the correct AP vif
first.
Fixes: openwrt#12420
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
[Rename to 360-wifi-mac80211-do-not-pass-ap_vlan-vif-pointer-to-dri.patch]
(cherry picked from commit
3e738781a9712eaa81d5af0ecc8b55cbfe480c68)
Link: https://github.com/openwrt/openwrt/pull/15898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
David Bauer [Sat, 22 Jul 2023 15:40:56 +0000 (17:40 +0200)]
mediatek: add missing SPDX header
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit
36f7ececc21fe6698a75f5ce9fc3ebf6c96a1b97)
Chukun Pan [Fri, 3 Nov 2023 15:02:35 +0000 (23:02 +0800)]
mediatek: filogic: add Netcore N60 support
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: ESMT F50L1G41LB 128MB
RAM: W632GU6NB DDR3 256MB
Ethernet: 1x 2.5G + 4x 1G
WiFi1: MT7975N 2.4GHz 4T4R
WiFi2: MT7975PN 5GHz 4T4R
Button: Reset, WPS
Power: DC 12V 2A
Flash instructions:
1. Connect to the router using ssh or telnet,
username: useradmin, password is the web
login password of the router.
2. Use scp to upload bl31-uboot.fip and flash:
"mtd write xxx-preloader.bin spi0.0"
"mtd write xxx-bl31-uboot.fip FIP"
"mtd erase ubi"
3. Connect to the router via the Lan port,
set a static ip of your PC.
(ip 192.168.1.254, gateway 192.168.1.1)
4. Download initramfs image, reboot router,
waiting for tftp recovery to complete.
5. After openwrt boots up, perform sysupgrade.
Note:
1. Back up all mtd partitions before flashing.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit
4ae474afbd023a3386f4276ca8f948a44b49ff1b)
Chukun Pan [Thu, 2 Nov 2023 15:16:28 +0000 (23:16 +0800)]
uboot-mediatek: add Netcore N60 support
The vendor uboot requires special fit verification.
So add a custom uboot build for this device.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit
0170666d89127585d30c3f1a8fdf641d9e8fbbbf)
Tianling Shen [Wed, 1 Nov 2023 06:46:15 +0000 (14:46 +0800)]
mediatek: add support for JDCloud RE-CP-03
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: 128GB eMMC
RAM: 1GB DDR4
Ethernet: 4x 1GbE, 1x 2.5GbE (RTL8221B)
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Joylink
Power: DC 12V 2A
Flash instructions:
1. Download and flash the vendor migration firmware via webUI:
https://firmware.download.immortalwrt.eu.org/cnsztl/mediatek/filogic/openwrt-mediatek-mt7986-jdcloud_re-cp-03-vendor-migration.bin
(Default address is 192.168.68.1, user root, no password)
2. After device has booted up, write new GPT table:
dd if=openwrt-mediatek-filogic-jdcloud_re-cp-03-gpt.bin of=/dev/mmcblk0 bs=512 seek=0 count=34 conv=fsync
3. Erase and write new BL2:
echo 0 > /sys/block/mmcblk0boot0/force_ro
dd if=/dev/zero of=/dev/mmcblk0boot0 bs=512 count=8192 conv=fsync
dd if=openwrt-mediatek-filogic-jdcloud_re-cp-03-preloader.bin of=/dev/mmcblk0boot0 bs=512 conv=fsync
4. Erase and write new FIP:
dd if=/dev/zero of=/dev/mmcblk0 bs=512 seek=13312 count=8192 conv=fsync
dd if=openwrt-mediatek-filogic-jdcloud_re-cp-03-bl31-uboot.fip of=/dev/mmcblk0 bs=512 seek=13312 conv=fsync
5. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
6. Serve OpenWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt has booted, perform sysupgrade.
9. Additionally, if you want to have eMMC recovery boot feature:
(Don't worry! You will always have TFTP recovery boot feature.)
dd if=openwrt-mediatek-filogic-jdcloud_re-cp-03-initramfs-recovery.itb of=/dev/mmcblk0p4 bs=512 conv=fsync
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit
c0c3234e17207a9287a08757fc1752490144a1cd)
Tianling Shen [Wed, 1 Nov 2023 06:44:50 +0000 (14:44 +0800)]
uboot-mediatek: add support for JDCloud RE-CP-03
The vendor U-Boot has enabled signature verification, so add
a custom U-Boot build for OpenWrt.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit
6fa4fbbc5293886aa6bae6e0cac4b99a4c472fc4)
Luis Mita [Thu, 6 Jun 2024 20:43:19 +0000 (16:43 -0400)]
ramips: mt76x8: sync Cudy TR1200 v1 naming
Cudy assigns hardware versions to its devices on its website, and
the Cudy TR1200 router is now Cudy TR1200 v1.
OpenWrt currently uses both variants, and this commit removes
inconsistencies using only the new name.
Signed-off-by: Luis Mita <luis@luismita.com>
(cherry picked from commit
d780d530dd89d135fffc6fb6598e6f7b28cd3921)
Link: https://github.com/openwrt/openwrt/pull/15875
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Luis Mita [Thu, 30 May 2024 18:50:23 +0000 (14:50 -0400)]
ramips: mt76x8: add support for Cudy TR1200 v1
Hardware:
- SoC: MediaTek MT7628AN (MIPS 580MHz)
- Flash: 16 MiB XMC 25QH128CH10
- RAM: 128 MiB ESMT M14D1G1664A
- WLAN: 2.4 GHz (MT7628), 5 GHz (MT7613BEN 802.11ac)
- Ethernet: 1x 10/100 Mbps WAN, 1x 10/100 LAN (MT7628)
- USB 2.0 port
- Buttons: 1 Reset button, 1 slider button
- LEDs: 1x Red, 1x White
- Serial console: unpopulated header, 115200 8n1
- Power: 5 VDC, 2 A
MAC addresses:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| WAN | 80:af:ca:xx:xx:x0 | label |
| LAN | 80:af:ca:xx:xx:x0 | label |
| WLAN 2g | 80:af:ca:xx:xx:x0 | label |
| WLAN 5g | 80:af:ca:xx:xx:x2 | label+2 |
+---------+-------------------+-----------+
Installation:
The installation must be done via TFTP by disassembling the router.
On other occasions Cudy has distributed intermediate firmware to make
installation easier, and so I recommend checking the Wiki for this
device if there is a more convenient solution than the one below.
To install using TFTP:
1. Upgrade to a beta firmware (signed by Cudy) that can be downloaded
from the wiki. This is required in order to use an unlocked u-boot.
2. Connect to UART.
3. While the router is turning on, press 1.
4. Connect to LAN and set your IP to 192.168.1.88/24. Configure a TFTP
server and an OpenWrt initramfs-kernel.bin firmware file as recovery.bin.
5. Press Enter three times. Verify the filename.
6. If you can reach LuCI or SSH now, just use the sysupgrade image with
the 'Keep settings' option turned off.
If you don't want to use the beta firmware nor the unlocked u-boot, you
can install the firmware writing the sysupgrade image on the firmware
partition of the SPI flash.
Signed-off-by: Luis Mita <luis@luismita.com>
(cherry picked from commit
f1091ef7ac3596f1e401b918a36273672acbe389)
Link: https://github.com/openwrt/openwrt/pull/15875
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sun, 7 Jul 2024 19:56:12 +0000 (21:56 +0200)]
mt76: Fix PKG_MIRROR_HASH
The PKG_MIRROR_HASH was updated to a wrong version.
Fixes: f64576f367eb ("mt76: update to Git HEAD (2024-04-03)")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Thu, 27 Jun 2024 23:32:46 +0000 (01:32 +0200)]
mac80211: Update to version 6.1.97-1
This updates mac80211 to version 6.1.97-1. This code is based on Linux
6.1.97 and contains all fixes included in the upstream wireless
subsystem from that kernel version. This includes many bugfixes and also
some security fixes.
The removed patches are already integrated in upstream Linux 6.1.97 or
in backports.
The following patches were integrated in upstream Linux:
ath11k/0013-wifi-ath11k-synchronize-ath11k_mac_he_gi_to_nl80211_.patch
ath11k/0035-wifi-ath11k-Use-platform_get_irq-to-get-the-interrup.patch
ath11k/0036-wifi-ath11k-fix-SAC-bug-on-peer-addition-with-sta-ba.patch
ath11k/0047-wifi-ath11k-fix-deinitialization-of-firmware-resourc.patch
ath11k/0053-wifi-ath11k-fix-writing-to-unintended-memory-region.patch
ath11k/0060-wifi-ath11k-Ignore-frags-from-uninitialized-peer-in-.patch
ath11k/0065-wifi-ath11k-fix-tx-status-reporting-in-encap-offload.patch
ath11k/0067-wifi-ath11k-Fix-SKB-corruption-in-REO-destination-ri.patch
ath11k/0069-wifi-ath11k-fix-registration-of-6Ghz-only-phy-withou.patch
ath11k/0080-wifi-ath11k-add-support-default-regdb-while-searchin.patch
ath11k/0085-wifi-ath11k-fix-memory-leak-in-WMI-firmware-stats.patch
ath11k/0086-wifi-ath11k-Add-missing-check-for-ioremap.patch
ath11k/0096-wifi-ath11k-fix-boot-failure-with-one-MSI-vector.patch
subsys/337-wifi-mac80211-fix-race-condition-on-enabling-fast-xm.patch
The following patches were integrated in upstream backports:
ath11k/901-wifi-ath11k-pci-fix-compilation-in-5.16-and-older.patch
build/080-resv_start_op.patch
build/110-backport_napi_build_skb.patch
The following files are missing in backports, we do not have to remove
them any more. Some were already missing before some were removed in
this update:
include/linux/cordic.h
include/linux/crc8.h
include/linux/eeprom_93cx6.h
include/linux/wl12xx.h
include/net/ieee80211.h
backport-include/linux/bcm47xx_nvram.h
include/linux/ath9k_platform.h
include/net/bluetooth/
backports ships a dummy Mediatek wed header for older kernel versions.
We backported the feature in our kernel, remove the dummy header:
backport-include/linux/soc/mediatek/mtk_wed.h
Remove header files for subsystems used form the mainline kernel:
include/trace/events/qrtr.h
include/net/rsi_91x.h
backport-include/linux/platform_data/brcmnand.h
Link: https://github.com/openwrt/openwrt/pull/15827
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Mon, 1 Jul 2024 21:55:03 +0000 (23:55 +0200)]
iw: sync nl80211.h
Update the nl80211.h file in iw with the version from backports.
The files were out of sync already before the mac80211 update. If iw set
the NL80211_ATTR_WIPHY_ANTENNA_GAIN attribute the kernel assumed it set
the NL80211_ATTR_PUNCT_BITMAP attribute because the id was the same.
Link: https://github.com/openwrt/openwrt/pull/15827
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Lu jicong [Tue, 2 Jul 2024 13:01:49 +0000 (21:01 +0800)]
target.mk: fix arm architecture level detection
Now kernel configs of armv6k CPUs don't include CONFIG_CPU_V6.
So armv6k CPUs cannot be detected as arm_v6.
Fix this by adding detection for CONFIG_CPU_V6K.
Signed-off-by: Lu jicong <jiconglu58@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15855
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit
d55083fbcaea9cdd2ebc10a2d38989ad485a5357)
Mathew McBride [Tue, 28 May 2024 23:09:17 +0000 (09:09 +1000)]
armsr: add realtek and smsc ethernet phy drivers to the default image
This adds two more common PHY brands to the image.
Realtek is used on the Google Coral "Phanbell" board (i.MX8MQ).
SMSC has been used on various Raspberry Pi boards.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(cherry picked from commit
bcbdde00c3a81a53d11ddc6101517185ae426691)
Link: https://github.com/openwrt/openwrt/pull/15808
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Mathew McBride [Sun, 26 May 2024 04:12:58 +0000 (14:12 +1000)]
armsr: enable framebuffer emulation for virtio-gpu/drm displays
This was discovered when trying to run OpenWrt on Hetzner Cloud's
Arm-based instances.
Hetzner uses QEMU/KVM with virtio-gpu as the main display device,
together with an ACPI firmware. This was not displaying a console
previously.
This setup can be emulated by qemu using options below:
qemu-system-aarch64 \
-machine virt \
-bios QEMU_EFI.fd \
-device virtio-gpu \
-usb \
-device qemu-xhci,id=xhci \
-device usb-tablet,bus=xhci.0 \
-device usb-kbd,bus=xhci.0 \
-vnc :0
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(cherry picked from commit
ea7383e7215c36e47a769f34c57aa458300b8bc2)
Link: https://github.com/openwrt/openwrt/pull/15808
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
John Vincent [Fri, 31 May 2024 13:56:24 +0000 (14:56 +0100)]
kernel: armsr: Renesas: RZ: Ethernet module and ttySC0
Ethernet module enable for Renesas RZ platform
inittab fix for ttySC0
Fixes: #15284
Signed-off-by: John Vincent <john.vincent.xa@bp.renesas.com>
(cherry picked from commit
531b3f667c40405581a398a9648a0e6c27909a87)
Link: https://github.com/openwrt/openwrt/pull/15808
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Mathew McBride [Tue, 30 Apr 2024 02:34:37 +0000 (12:34 +1000)]
armsr: armv8: enable serial console for Renesas platforms
Support for Renesas Arm families was added in commit
1ff4f4df2301
("armsr: armv8: enable CONFIG_ARCH_RENESAS"), but this did not
enable the console/tty hardware for these SoCs, which is derived
from the SuperH family (CONFIG_SERIAL_SH_SCI).
Link: https://github.com/openwrt/openwrt/issues/15284
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(cherry picked from commit
683355d0a6d51cbeda258492bc16a9c6413b387e)
Link: https://github.com/openwrt/openwrt/pull/15808
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Roland Reinl [Sun, 12 Nov 2023 18:04:32 +0000 (19:04 +0100)]
mediatek: Add support for D-Link EAGLE PRO AI R32
R32 is like the M32 part of the EAGLE PRO AI series from D-Link.
Specification:
- MT7622BV SoC with 2.4GHz wifi
- MT7975AN + MT7915AN for 5GHz
- MT7531BE Switch
- 512MB RAM
- 128 MB flash
- 2 LEDs (Status and Internet, both can be either orange or white)
- 2 buttons (WPS and Reset)
Compared to M32, the R32 has the following differences:
- 4 LAN ports instead of 2
- The recory image starts with DLK6E6015001 instaed of DLK6E6010001
- Individual LEDs for power and internet
- MAC address is stored at another offset in the ODM partition
MAC addresses:
- WAN MAC is stored in partition "Odm" at offset 0x81
- LAN (as printed on the device) is WAN MAC + 1
- WLAN MAC (2.4 GHz) is WAN MAC + 2
- WLAN MAC (5GHz) is WAN MAC + 3
Flashing via Recovery Web Interface:
- Set your IP address to 192.168.0.10, subnetmask 255.255.255.0
- Press the reset button while powering on the deivce
- Keep the reset button pressed until the internet LED blinks fast
- Open a Chromium based and goto http://192.168.0.1
- Download openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-a1-squashfs-recovery.bin
Flashing via uBoot:
- Open the case, connect to the UART console
- Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router
- Run a tftp server which provides openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-initramfs-kernel.bin.
- You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later.
- Power on the device and select "1. System Load Linux to SDRAM via TFTP." in the boot menu
- Enter image file, tftp server IP and device IP (if they differ from the default).
- TFTP download to RAM will start. After a few seconds OpenWrt initramfs should start
- The initramfs is accessible via 192.168.1.1, change your IP address accordingly (or use multiple IP addresses on your interface)
- Create a backup of the Kernel1 partition, this file is required if a revert to stock should be done later
- Perform a sysupgrade using openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-squashfs-sysupgrade.bin
- Reboot the device. OpenWrt should start from flash now
Revert back to stock using the Recovery Web Interface:
- Set your IP address to 192.168.0.10, subnetmask 255.255.255.0
- Press the reset button while powering on the deivce
- Keep the reset button pressed until the internet LED blinks fast
- Open a Chromium based and goto http://192.168.0.1
- Flash a decrypted firmware image from D-Link. Decrypting an firmware image is described below.
Decrypting a D-Link firmware image:
- Download https://github.com/RolandoMagico/firmware-utils/blob/M32/src/m32-firmware-util.c
- Compile a binary from the downloaded file, e.g. gcc m32-firmware-util.c -lcrypto -o m32-firmware-util
- Run ./m32-firmware-util R32 --DecryptFactoryImage <OriginalFirmware> <OutputFile>
- Example for firmware R32A1_FW103B01: ./m32-firmware-util R32 --DecryptFactoryImage R32A1_FW103B01.bin R32A1_FW103B01.decrypted.bin
Revert back to stock using uBoot:
- Open the case, connect to the UART console
- Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router
- Run a tftp server which provides the previously created backup of the Kernel1 partition.
- You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later.
- Power on the device and select "2. System Load Linux Kernel then write to Flash via TFTP." in the boot menu
- Enter image file, tftp server IP and device IP (if they differ from the default).
- TFTP download to FLASH will start. After a few seconds the stock firmware should start again
There is also an image openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-a1-squashfs-tftp.bin which can directly be flashed via U-Boot and TFTP.
It can be used if no backup of the Kernel1 partition is reuqired.
Flahsing via OEM web interface is currently not possible, the OEM images are encrypted. Creating images is only possible manually at the moment.
The support for the M32/R32 already includes support for flashing from the OEM web interface:
- The device tree contains both partitions (Kernel1 and Kernel2) with conditions to select the correct one based on the kernel command line
- The U-Boot variable "boot_part" is set accordingly during startup to finish the partition swap after flashing from the OEM web interface
- OpenWrt sysupgrade flashing always uses the partition where it was initially flashed to (no partition swap)
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
(cherry picked from commit
fdb87a91b4202ad1a58fe46f499e4e68bf82de4e)
Link: https://github.com/openwrt/openwrt/pull/15776
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fabrice Fontaine [Sat, 27 Apr 2024 15:50:05 +0000 (17:50 +0200)]
package/utils/secilc: drop PKG_CPE_ID
cpe:/a:selinuxproject:secilc is not a correct CPE ID for secilc:
https://nvd.nist.gov/products/cpe/search/results?keyword=cpe:2.3:a:selinuxproject:secilc
Fixes: 9ee7c1ec60e23f25f5d275c6439ce93aec914e1c (secilc: adds new package)
Signed-off-by: Fabrice Fontaine <fontaine.fabrice@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15298
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit
58a5877846e2913bed4fd982386797d7751f58f0)
Link: https://github.com/openwrt/openwrt/pull/15881
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fabrice Fontaine [Sat, 27 Apr 2024 15:25:58 +0000 (17:25 +0200)]
package/network/utils/iptables: fix PKG_CPE_ID
cpe:/a:netfilter:iptables is the correct CPE ID for iptables:
https://nvd.nist.gov/products/cpe/search/results?keyword=cpe:2.3:a:netfilter:iptables
Fixes: c61a2395140d92cdd37d3d6ee43a765427e8e318 (add PKG_CPE_ID ids to package and tools)
Signed-off-by: Fabrice Fontaine <fontaine.fabrice@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15297
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit
6e5edec159e2dc468607a5b9179f722857a38421)
Link: https://github.com/openwrt/openwrt/pull/15881
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fabrice Fontaine [Fri, 26 Apr 2024 15:47:24 +0000 (17:47 +0200)]
package/libs/libjson-c: fix PKG_CPE_ID
cpe:/a:json-c:json-c is the correct CPE ID for libjson-c:
https://nvd.nist.gov/products/cpe/search/results?keyword=cpe:2.3:a:json-c:json-c
Fixes: c61a2395140d92cdd37d3d6ee43a765427e8e318 (add PKG_CPE_ID ids to package and tools)
Signed-off-by: Fabrice Fontaine <fontaine.fabrice@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15292
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit
a4f723e04ed245819fe320f472a4ff2b4eda00fb)
Link: https://github.com/openwrt/openwrt/pull/15881
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fabrice Fontaine [Fri, 26 Apr 2024 14:09:32 +0000 (16:09 +0200)]
package/network/services/dropbear: fix PKG_CPE_ID
cpe:/a:dropbear_ssh_project:dropbear_ssh is the correct CPE ID for dropbear:
https://nvd.nist.gov/products/cpe/search/results?keyword=cpe:2.3:a:dropbear_ssh_project:dropbear_ssh
Fixes: c61a2395140d92cdd37d3d6ee43a765427e8e318 (add PKG_CPE_ID ids to package and tools)
Signed-off-by: Fabrice Fontaine <fontaine.fabrice@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15290
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit
289f811abb4ace7aa08ae7bf85c0d4f9460f0802)
Link: https://github.com/openwrt/openwrt/pull/15881
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fabrice Fontaine [Fri, 26 Apr 2024 08:41:15 +0000 (10:41 +0200)]
toolchain/nasm: fix PKG_CPE_ID
cpe:/a:nasm:netwide_assembler is the correct CPE ID for nasm:
https://nvd.nist.gov/products/cpe/search/results?keyword=cpe:2.3:a:nasm:netwide_assembler
Fixes: bcf02c5d3123a99c717ca33f1d7c6250acf0f33f (toolchain: assign PKG_CPE_ID)
Signed-off-by: Fabrice Fontaine <fontaine.fabrice@gmail.com>
(cherry picked from commit
e1ca08518e96ccf088119fbc9930c5e4beef86cc)
Link: https://github.com/openwrt/openwrt/pull/15881
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fabrice Fontaine [Fri, 26 Apr 2024 08:51:16 +0000 (10:51 +0200)]
tools/flex: fix PKG_CPE_ID
cpe:/a:westes:flex is the correct CPE ID for flex:
https://nvd.nist.gov/products/cpe/search/results?keyword=cpe:2.3:a:westes:flex
Fixes: c61a2395140d92cdd37d3d6ee43a765427e8e318 (add PKG_CPE_ID ids to package and tools)
Signed-off-by: Fabrice Fontaine <fontaine.fabrice@gmail.com>
(cherry picked from commit
832460b452d840451adf44713e90515fc61c88ab)
Link: https://github.com/openwrt/openwrt/pull/15881
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fabrice Fontaine [Fri, 26 Apr 2024 08:59:58 +0000 (10:59 +0200)]
tools/zlib: fix PKG_CPE_ID
cpe:/a:zlib:zlib is the correct CPE ID for zlib:
https://nvd.nist.gov/products/cpe/search/results?keyword=cpe:2.3:a:zlib:zlib
Fixes: c61a2395140d92cdd37d3d6ee43a765427e8e318 (add PKG_CPE_ID ids to package and tools)
Signed-off-by: Fabrice Fontaine <fontaine.fabrice@gmail.com>
(cherry picked from commit
e9ecaade6f1f9bd821523a3b731bfaaf5ab5ca35)
Link: https://github.com/openwrt/openwrt/pull/15881
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fabrice Fontaine [Fri, 26 Apr 2024 13:09:50 +0000 (15:09 +0200)]
package/libs/pcre2: fix PKG_CPE_ID
cpe:/a:pcre:pcre2 is the correct CPE ID for pcre2:
https://nvd.nist.gov/products/cpe/search/results?keyword=cpe:2.3:a:pcre:pcre2
Fixes: c39b0646f3f2d96d40f601209859175af8537b6d (pcre2: import pcre2 from packages feed)
Signed-off-by: Fabrice Fontaine <fontaine.fabrice@gmail.com>
(cherry picked from commit
27d1ebb46adfd58db9a8034336c2d85b41f617f9)
Link: https://github.com/openwrt/openwrt/pull/15881
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Sean Khan [Sun, 9 Jun 2024 01:02:30 +0000 (21:02 -0400)]
openssl: conditionally disable engine section
Currently, the build option to enable/disable engine support isn't
reflected in the final '/etc/ssl/openssl.cnf' config. It assumes `engines`
is always enabled, producing an error whenever running any
commands in openssl util or programs that explicitly use settings
from '/etc/ssl/openssl.cnf'.
```
➤ openssl version
FATAL: Startup failure (dev note: apps_startup()) for openssl
307D1EA97F000000:error:
12800067:lib(37):dlfcn_load:reason(103):crypto/dso/dso_dlfcn.c:118:filename(libengines.so):
Error loading shared library libengines.so: No such file or directory
307D1EA97F000000:error:
12800067:lib(37):DSO_load:reason(103):crypto/dso/dso_lib.c:152:
307D1EA97F000000:error:
0700006E:lib(14):module_load_dso:reason(110):crypto/conf/conf_mod.c:321:module=engines, path=engines
307D1EA97F000000:error:
07000071:lib(14):module_run:reason(113):crypto/conf/conf_mod.c:266:module=engines
```
Build should check for the `CONFIG_OPENSSL_ENGINE` option, and comment out `engines`
if not explicitly enabled.
Example:
```
[openssl_init]
providers = provider_sect
```
After this change, openssl util works correctly.
```
➤ openssl version
OpenSSL 3.0.14 4 Jun 2024 (Library: OpenSSL 3.0.14 4 Jun 2024)
```
Signed-off-by: Sean Khan <datapronix@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/15661
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit
31ec4515c3c14704d669156d87e2af5eeb5420e4)
Link: https://github.com/openwrt/openwrt/pull/15873
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
John Audia [Wed, 5 Jun 2024 19:55:29 +0000 (15:55 -0400)]
openssl: update to 3.0.14
Major changes between OpenSSL 3.0.13 and OpenSSL 3.0.14 [04-Jun-2024]
* Fixed potential use after free after SSL_free_buffers() is called.
[CVE-2024-4741]
* Fixed checking excessively long DSA keys or parameters may be very slow.
[CVE-2024-4603]
* Fixed an issue where some non-default TLS server configurations can cause
unbounded memory growth when processing TLSv1.3 sessions. An attacker may
exploit certain server configurations to trigger unbounded memory growth that
would lead to a Denial of Service. [CVE-2024-2511]
* New atexit configuration switch, which controls whether the OPENSSL_cleanup
is registered when libcrypto is unloaded. This can be used on platforms
where using atexit() from shared libraries causes crashes on exit
Signed-off-by: John Audia <therealgraysky@proton.me>
Build system: x86/64
Build-tested: x86/64/AMD Cezanne
(cherry picked from commit
bac2f1bed6db5da166aad7b1091c2e9af0ffef5d)
Link: https://github.com/openwrt/openwrt/pull/15873
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sun, 21 Apr 2024 15:46:55 +0000 (17:46 +0200)]
wolfssl: Update to 5.7.0
This fixes multiple security problems:
* [High] CVE-2024-0901 Potential denial of service and out of bounds
read. Affects TLS 1.3 on the server side when accepting a connection
from a malicious TLS 1.3 client. If using TLS 1.3 on the server side
it is recommended to update the version of wolfSSL used.
* [Med] CVE-2024-1545 Fault Injection vulnerability in
RsaPrivateDecryption function that potentially allows an attacker
that has access to the same system with a victims process to perform
a Rowhammer fault injection. Thanks to Junkai Liang, Zhi Zhang, Xin
Zhang, Qingni Shen for the report (Peking University, The University
of Western Australia)."
* [Med] Fault injection attack with EdDSA signature operations. This
affects
ed25519 sign operations where the system could be susceptible
to Rowhammer attacks. Thanks to Junkai Liang, Zhi Zhang, Xin Zhang,
Qingni Shen for the report (Peking University, The University of
Western Australia).
Size increased a little:
wolfssl 5.6.6:
516880 bin/packages/mips_24kc/base/libwolfssl5.6.6.e624513f_5.6.6-stable-r1_mips_24kc.ipk
wolfssl: 5.7.0:
519429 bin/packages/mips_24kc/base/libwolfssl5.7.0.e624513f_5.7.0-stable-r1_mips_24kc.ipk
(cherry picked from commit
f475a44c03a303851959930030ab9e6acebb81a7)
Link: https://github.com/openwrt/openwrt/pull/15872
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Nick Hainke [Wed, 27 Dec 2023 13:21:46 +0000 (14:21 +0100)]
wolfssl: update to 5.6.6
Release Notes:
https://github.com/wolfSSL/wolfssl/releases/tag/v5.6.6-stable
Refresh patches:
- 100-disable-hardening-check.patch
Fixes: CVE-2023-6935 CVE-2023-6936 CVE-2023-6937
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry picked from commit
511578c128121326a3c48fdb35e4e62f96dc7b9d)
Link: https://github.com/openwrt/openwrt/pull/15872
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
David Bentham [Fri, 10 Nov 2023 18:50:38 +0000 (18:50 +0000)]
mediatek: add Comfast CF-E393AX support
Comfast CF-E393AX is a dual-band Wi-Fi 6 POE ceiling mount access point.
Oem firmware is a custom openwrt 21.02 snapshot version.
We can gain access via ssh once we remove the root password.
Hardware specification:
SoC: MediaTek MT7981A 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB DDR3
Ethernet: 1x 10/100/1000 Mbps built-in PHY (WAN)
1x 10/100/1000/2500 Mbps MaxLinear GPY211C (LAN)
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976D
LEDS: 1x (Red, Blue and Green)
Button: Reset
UART: 3.3v, 115200n8
--------------------------
| Layout |
| ----------------- |
| 4 | VCC GND TX RX | <= |
| ----------------- |
--------------------------
Gain SSH access:
1. Login into web interface (http://apipaddress/computer/login.html),
and download the
configuration(http://apipaddress/computer/config.html).
2. Rename downloaded backup config - 'backup.file to backup.tar.gz',
Enter 'fakeroot' command then decompress the configuration:
tar -zxf backup.tar.gz
3. Edit 'etc/shadow', update (remove) root password:
With password =
'root:$1$xf7D0Hfg$5gkjmvgQe4qJbe1fi/VLy1:19362:0:99999:7:::'
'root:$1$xf7D0Hfg$5gkjmvgQe4qJbe1fi/VLy1:19362:0:99999:7:::'
to
Without password =
'root::0:99999:7:::'
'root::0:99999:7:::'
4. Repack 'etc' directory back to a new backup file:
tar -zcf backup-ssh.tar.gz etc/
5. Rename new config tar.gz file to 'backup-ssh.file'
Exit fakeroot - 'exit'
6. Upload new configuration via web interface, now you
can SSH with the following:
'ssh -vv -o HostKeyAlgorithms=+ssh-rsa \
-o PubkeyAcceptedAlgorithms=+ssh-rsa root@192.168.10.1'.
Backup the mtd partitions
- https://openwrt.org/docs/guide-user/installation/generic.backup
7. Copy openwrt factory firmware to the tmp folder to install via ssh:
'scp -o HostKeyAlgorithms=+ssh-rsa \
-o PubkeyAcceptedAlgorithms=+ssh-rsa \
*-mediatek-filogic-comfast_cf-e393ax-squashfs-factory.bin \
root@192.168.10.1:/tmp/'
'sysupgrade -n -F \
/tmp/*--mediatek-filogic-comfast_cf-e393ax-squashfs-factory.bin'
8. Once led has stopped flashing - Connect via ssh with the
default openwrt ip address - 'ssh root@192.168.1.1'
9. SSH copy the openwrt sysupgrade firmware and upgrade
as per the default instructions.
Signed-off-by: David Bentham <db260179@gmail.com>
(cherry picked from commit
d8f4453bf2de9fd9baf3d660ed12e0797ff2cfdb)
Leon M. Busch-George [Fri, 13 Oct 2023 10:44:11 +0000 (12:44 +0200)]
mediatek: add support for YunCore AX835
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 16MB NOR
RAM: 256MB
Ethernet: 2x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset
Power: DC 12V 1A, PoE 802.3af 48V
Flash instructions:
Option #1 - SSH
I was able to SSH into the stock firmware of my device.
1. Attach the router to the network
2. Use scp (-O) to copy the sysupgrade image
3. Connect using SSH and run `sysupgrade -n`
Option #2 - U-Boot
One way to use the bootloader for flashing is using TFTP:
1. Connect to the router using an ethernet cable
2 Spin up a TFTP server serving the sysupgrade file
3. Open the case and attach a UART
4. Attach power to the router and interrupt the countdown by pressing
any key
5. Select option #2 (Upgrade firmware)
6. Enter IP address information and image name
7. Wait patiently
Co-Authored-By: Enrique Rodríguez Valencia <enrique.rodriguez@galgus.net>
Co-Authored-By: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
(cherry picked from commit
b4086f44cd8a739458a0fd12cfaf684515507614)
Daniel Golle [Fri, 17 Nov 2023 02:25:09 +0000 (02:25 +0000)]
mediatek: add support for Adtran SmartRG Bonanza Peak series
The Bonanza Peak series are a couple of MT7986-powered 2.5 GBit/s
Wi-Fi 6 residential gateway, access point and mesh router products.
All of them come with an eMMC to boot from, are powered via USB-C and
got a USB 3.0 type-A port. All of them got a Dialog (Renesas)
DA14531
Bluetooth module connected via UART. If the device was previously
running stock firmware, the BT chip's internal flash has been loaded
with firmware and it can be attached using hciattach when using
OpenWrt.
SOC: MediaTek MT7986A
RAM: 2 GiB DDR4
eMMC: 8 GiB
Bluetooth: BLE5 (
DA14531)
Serial: 3.3V level, 115200 8n1 on 4-pin connector
* SDG-8612 - Dual-band RJ-45 gateway
2x 2.5G MaxLinear PHY for WAN port
3x 1GE LAN ports via MT7531 switch
* SDG-8614 - Dual-band SFP gateway
1x SFP cage with up to 2.5G speed
1x 2.5G MaxLinear PHY for LAN port
3x 1GE LAN ports via MT7531 switch
* SDG-8622 - Tri-band mesh router
2x 2.5G MaxLinear PHY
The MT7986 2G and 5G are used as 2G and 5G high band.
There’s a MT7915 PCIe card for 5G low band.
* SDG-8632 - Tri-band mesh router with 6 GHz
2x 2.5G MaxLinear PHY
The MT7986 serves the 2G and 6G bands.
There’s a MT7915 PCIe card for 5G.
Installation via U-Boot serial console:
0. setup TFTP server with IP 192.168.1.10/24, place initramfs image
renamed to openwrt.XXX where XXX is the internal product number:
SDG-8612: XXX = 412
SDG-8614: XXX = 414
SDG-8622: XXX = 422
SDG-8632: XXX = 432
1. connect to the serial console and power on the device.
Interrupt the bootloader by pressing 'st'
2. setenv boot_mode openwrt ; saveenv
3. run boot1
Load firmware via TFTP and write to flash
4. run boot2
Now OpenWrt initramfs should boot
5. upload sysupgrade.bin via scp to /tmp
6. sysupgrade
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit
3aa686f8d4d89ab28e749874c4b5e82d46685f3c)
Chukun Pan [Sun, 5 Nov 2023 15:02:09 +0000 (23:02 +0800)]
uboot-envtools: filogic: reorder alphabetically
Reorder scripts to keep alphabetical order.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit
4825defe449883cb287bc46a93048473878003f0)
Rafał Miłecki [Sun, 17 Mar 2024 21:20:14 +0000 (22:20 +0100)]
kernel: backport some useful LED_FUNCTION_* defines for DT
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit
081cd769fc3e1de7709d7473b2560aaa549e2b05)
Shiji Yang [Tue, 31 Oct 2023 10:21:37 +0000 (18:21 +0800)]
generic: add more DT LED color and function definitions
Openwrt supports hundreds of devices. These newly added LED colors
and functions can help developers better describe LED indicators.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit
6c41c585e37c44e25bc8d63c216635285aa05461)
Felix Fietkau [Thu, 16 May 2024 20:15:09 +0000 (22:15 +0200)]
mt76: update to Git HEAD (2024-04-03)
605624a4e17b mt76: fix path to page_pool helper include
e4de3592c4e3 wifi: mt76: mt7603: fix tx queue of loopback packets
446f652c967c wifi: mt76: mt7603: add wpdma tx eof flag for PSE client reset
669aba47a145 wifi: mt76: mt7915: fix HE PHY capability regression
5914ea57a31f wifi: mt76: mt7915: workaround dubious x | !y warning
e8b5991f7dac wifi: mt76: mt7915: workaround too long expansion sparse warnings
e507b4e32ead wifi: mt76: mt7921: fix fw used for offload check for mt7922
725f531c1459 wifi: mt76: connac: check for null before dereferencing
b108dda7e201 wifi: mt76: mt7996: fix size of txpower MCU command
5b7616491f07 wifi: mt76: mt7921: introduce mt7920 PCIe support
0436995feca9 wifi: mt76: mt7921s: fix potential hung tasks during chip recovery
75759dca73d5 wifi: mt76: mt7925: ensure 4-byte alignment for suspend & wow command
b96ab5e62010 wifi: mt76: mt7996: fix uninitialized variable in mt7996_irq_tasklet()
7ff11c7259a3 wifi: mt76: sdio: move mcu queue size check inside critical section
02846a5d0f0f wifi: mt76: mt7915: Remove unused of_gpio.h
cb8df32e0475 wifi: mt76: mt7996: disable rx header translation for BMC entry
a4c4b550512e wifi: mt76: connac: use peer address for station BMC entry
260c5b7c3ba0 wifi: mt76: mt7996: set RCPI value in rate control command
0b7e645db9c2 wifi: mt76: connac: enable HW CSO module for mt7996
f19035fe0b4d wifi: mt76: mt7996: fix non-main BSS no beacon issue for MBSS scenario
424e9df466ce wifi: mt76: mt7996: fix potential memory leakage when reading chip temperature
f70cb4f0508e wifi: mt76: connac: enable critical packet mode support for mt7992
5f1bf8865247 wifi: mt76: mt7996: add sanity checks for background radar trigger
1e336a8582dc wifi: mt76: connac: use muar idx 0xe for non-mt799x as well
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit
a10a6fbac794b30885d65ec817ebdcfe9f94d78a)
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Ian Oderon [Sat, 9 Dec 2023 04:48:35 +0000 (12:48 +0800)]
mediatek: add support for Zbtlink ZBT-Z8103AX
Specifications:
SoC: MediaTek MT7981B
RAM: 256MiB
Flash: SPI-NAND 128 MiB
Switch: 1 WAN, 3 LAN (Gigabit)
Buttons: Reset, Mesh
Power: DC 12V 1A
WiFi: MT7976CN
UART: 115200n8
UART Layout:
VCC-RX-TX-GND
No. of Antennas: 6
Note: Upon opening the router, only 5 antennas were connected
to the mainboard.
Led Layout:
Power-Mesh-5gwifi-WAN-LAN3-LAN2-LAN1-2gWiFi
Buttons:
Reset-Mesh
Installation:
A. Through OpenWrt Dashboard:
If your router comes with OpenWrt preinstalled (modified by the seller),
you can easily upgrade by going to the dashboard (192.168.1.1) and then
navigate to System -> Backup/Flash firmware, then flash the firmware
B. Through TFTP
Standard installation via UART:
1. Connect USB Serial Adapter to the UART, (NOTE: Don't connect the VCC pin).
2. Power on the router. Make sure that you can access your router via UART.
3. Restart the router then repeatedly press ctrl + c to skip default boot.
4. Type > bootmenu
5. Press '2' to select upgrade firmware
6. Press 'Y' on 'Run image after upgrading?'
7. Press '0' and hit 'enter' to select TFTP client (default)
8. Fill the U-Boot's IP address and TFTP server's IP address.
9. Finally, enter the 'firmware' filename.
Signed-off-by: Ian Oderon <ianoderon@gmail.com>
(cherry picked from commit
4300bc668819a77226b6e8ea079d3067f216e7bb)
Rodrigo Balerdi [Sat, 6 Apr 2024 06:18:00 +0000 (03:18 -0300)]
base-files: minor fix to mmc_get_mac_ascii function
This is mostly a cosmetic cleanup. The absence of
the return statement was not causing any problems.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
(cherry picked from commit
8cf4ac5195476356a14678ae72897e563881b15e)
Daniel Golle [Fri, 17 Nov 2023 00:02:05 +0000 (00:02 +0000)]
base-files: add mmc_get_mac_ascii function
Similar to the *_get_mac_binary function, also split the common parts
off mtd_get_mac_ascii into new get_mac_ascii function and introduce
mmc_get_mac_ascii which uses it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit
45c85c1827d45f8041b8f270d80bf6fff328069c)
Daniel Golle [Wed, 29 Nov 2023 21:10:37 +0000 (21:10 +0000)]
mediatek: add kmod-usb3 to default package set of the ZBT-Z8102AX
Include XHCI USB drivers on the ZBT-Z8102AX router, the drivers are
required to be able to use the USB-connected M.2 slots for 4G/5G modems.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit
507ad4f078d202304414a795d580abdee64f2b84)
Hauke Mehrtens [Sat, 29 Jun 2024 16:44:56 +0000 (18:44 +0200)]
kernel: bump 5.15 to 5.15.161
No manual changes needed.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit
19305aff72990e1be1f23c9cb91659cc6a89b7fa)
Hauke Mehrtens [Sun, 26 May 2024 16:49:49 +0000 (18:49 +0200)]
kernel: bump 5.15 to 5.15.160
No manual changes needed.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit
c569b7d21a74bfbba2246514f7ca12e6565aeb93)
Hauke Mehrtens [Sun, 26 May 2024 11:47:33 +0000 (13:47 +0200)]
kernel: bump 5.15 to 5.15.159
Removed because they are upstream:
generic/pending-5.15/778-net-l2tp-drop-flow-hash-on-forward.patch
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-5.15.y&id=
e97e0051056b6dbcc43ae1862dcfcb05d06517c3
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit
6cfa186544c1b787bb3dfafed64c4f2eee2168cd)
Ryan Castellucci [Mon, 6 May 2024 14:12:10 +0000 (15:12 +0100)]
ipq40xx: eap1300: add eap1300ext as alt model
The EnGenius EAP1300 and EAP1300EXT use identical boards and firmware
(as flashed) from the vendor.
As with the EAP1300, the EAP1300EXT requires a specific firmware version
to flash OpenWRT. Unfortunately, the required firmware is truncated on
the vendor's website.
A working file can be created as follows:
```
curl \
https://www.engeniustech.com/wp_firmware/eap1300-all-v3.5.3.5_c1.9.04.bin \
| perl -pe 's/\x09EAP1300_A/\x0cEAP1300EXT_A/' \
> eap1300ext-all-v3.5.3.5_c1.9.04.bin
```
The file should have sha256:
`
58a1197a426139a12b03fd432334e677124cbe3384349bd7337f2ee71f1dcfd4`.
Please see commit
2b4ac79 for further
details.
The vendor firmware must be decrypted before it can be flashed from
OpenWRT. A tool able to do that is available from:
https://github.com/ryancdotorg/enfringement/blob/main/decrypt.py
Signed-off-by: Ryan Castellucci <code@ryanc.org>
(cherry picked from commit
85f6f882232367b64c7933fb4856fdf4999c6aae)
David Bauer [Thu, 27 Jun 2024 20:59:50 +0000 (22:59 +0200)]
hostapd: bump PKG_RELEASE
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit
89d705148553a19a9dc32191cc85aff7616cf536)
David Bauer [Thu, 27 Jun 2024 20:58:56 +0000 (22:58 +0200)]
hostapd: don't ignore probe-requests with invalid DSSS params
Don't ignore probe requests which contain an invalid DS parameter for the
current operating channel.
As the comment outlines, the drop shall only apply if
dot11RadioMeasurementActivated is set to 1.
However, it was observed Linux clients (Debian 12 / NixOS 23.11)
with an Intel 8265 NIC may generate a probe request frame with
dot11RadioMeasurementActivated set to false and an invalid DSSS
parameter.
These were also dropped even though they should not have been. They
however should not have contained this parameter in the first place.
Don't drop Probe Requests which contain such an invalid field. This may
lead to more probe responses being sent, however it does fix very
frequent connection issues for these clients on 2.4 GHz.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit
68e4cc9be5f6f485c2d3b00cf4e2f14e98aecee2)
Daniel Golle [Tue, 25 Jun 2024 19:40:59 +0000 (20:40 +0100)]
ramips: yuncore_g720: fix buttons
Turns out the device got two buttons, while the currently listed on is
actually WPS, and the other (will hidden) button is intended as RESET.
Update DT accordingly.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit
646ebbd32ca4d776c64c31e85c08dc72fec25d7d)
Roman Azarenko [Tue, 4 Jun 2024 16:00:03 +0000 (18:00 +0200)]
build: add explicit timezone in CycloneDX SBOM
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
Per the CycloneDX 1.4 spec, the `metadata.timestamp` field contains
the date/time when the BOM was created [1].
Before the change, the value generated by the package-metadata.pl
script would look like this:
2024-06-03T15:51:10
CycloneDX 1.4 relies on the JSON Schema specification version draft-07,
which defines the `date-time` format [2] as derived from RFC 3339,
section 5.6 [3]. In this format, the `time-offset` component is required,
however in the original version of package-metadata.pl it is omitted.
This is causing problems with OWASP Dependency-Track version 4.11.0 or
newer, where it now validates submitted SBOMs against the JSON schema
by default [4]. SBOMs with incorrect timestamp values are rejected with
the following error:
{
"detail": "Schema validation failed",
"errors": [
"$.metadata.timestamp: 2024-06-03T15:51:10 is an invalid date-time"
],
"status": 400,
"title": "The uploaded BOM is invalid"
}
Add explicit `Z` (UTC) timezone offset in the `timestamp` field
to satisfy the CycloneDX schema.
[1]: https://github.com/CycloneDX/specification/blob/1.4/schema/bom-1.4.schema.json#L116-L121
[2]: https://json-schema.org/draft-07/draft-handrews-json-schema-validation-01#rfc.section.7.3.1
[3]: https://datatracker.ietf.org/doc/html/rfc3339#section-5.6
[4]: https://github.com/DependencyTrack/dependency-track/pull/3522
Signed-off-by: Roman Azarenko <roman.azarenko@iopsys.eu>
(cherry picked from commit
2ded629864de779df8ddd0224a875edf17f9fea5)
Link: https://github.com/openwrt/openwrt/pull/15693
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Felix Fietkau [Thu, 16 May 2024 20:15:08 +0000 (22:15 +0200)]
mt76: update to Git HEAD (2024-03-18)
a903d3169193 wifi: mt76: mt7921: fix a potential association failure upon resuming
eb0d0ce344f3 wifi: mt76: mt7921: fix suspend issue on MediaTek COB platform
841bf82e9958 wifi: mt76: fix the issue of missing txpwr settings from ch153 to ch177
ce7ccc540168 wifi: mt76: Remove redundant assignment to variable tidno
a238df940d6f wifi: mt76: mt7915: initialize rssi on adding stations
46c7d1849dbd wifi: mt76: replace skb_put with skb_put_zero
b5640b3153c7 wifi: mt76: fix tx packet loss when scanning on DBDC
7b054e5cb3af wifi: mt76: mt7915: fix mcu command format for mt7915 tx stats
3f27a64a8010 wifi: mt76: mt7915: fix bogus Tx/Rx airtime duration values
4f681a8fbc91 wifi: mt76: mt7915: fix HE PHY capabilities IE for station mode
8ede229eb8b5 wifi: mt76: mt7915: only set MT76_MCU_RESET for the main phy
2330781b8c5f wifi: mt76: mt7996: only set MT76_MCU_RESET for the main phy
e5fb6995e7eb wifi: mt76: mt7915: add support for disabling in-band discovery
b4a917417c85 wifi: mt76: mt7915: add mt7986, mt7916 and mt7981 pre-calibration
2135e201e7a9 mt76: mt7915: add fallback in case of missing precal data
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit
85ad6b9569683d6cc5808d1797af7de0e781aa1d)
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
David Bauer [Sat, 15 Jun 2024 23:33:19 +0000 (01:33 +0200)]
mpc85xx: fix label-mac-address for Enterasys WS-AP3710i
The WS-AP3710i does not correctly expose its label-mac on eth0 anymore
since the change to simpleLoader.
Fix this by obtaining the label-mac from the U-Boot environment.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit
e321e70ddcd82e0b4a5ad695b83a88d44cde02b4)
David Bauer [Fri, 14 Jun 2024 20:50:26 +0000 (22:50 +0200)]
mpc85xx: fix Enterasys WS-AP3710i eth mac-address
With the introduction of the simpleImage loader, the MAC address is not
set by the bootloader anymore.
Fix this by reading the MAC address from the U-Boot environment
partition.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit
22f92cce22401ef7df44357a7e6921d2cf45c840)
David Bauer [Sun, 9 Jun 2024 17:34:46 +0000 (19:34 +0200)]
mpc85xx: fix WS-AP3710i boot
On master, the bootwrapper link-address for all simpleImage targets was
relocated to 0x15000000 due to growing kernel size.
This was not done on OpenWrt 23.05, as the decompressed kernel still
fits. However, with the wrapper for the WS-AP3710i, the bootloader
attempts execute in-place with the uImage load-address of 0x1000000. As
the image is compiled without the uImage header in mind, this naturally
fails.
In order to fix this, link the WS-AP3715i simpleImage at 0x15000000 as
done in master. This will force the bootloader to relocate the code to
the proper address and skip XIP.
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Fri, 7 Jun 2024 17:23:56 +0000 (19:23 +0200)]
ipq40xx: fix broken image generation for EX6150v2
All NETGEAR EX6150v2 validate the rootfs for which OpenWrt places a
fakeheader at the position, where the bootloader expects it.
Some EX6150v2 bootloaders do however make a broken assumption about
where the rootfs starts. This is due to them calculating the rootfs
start not based upon the kernel-length but the string-offset of the
FIT-image.
We have to be compatible with both this broken as well as the valid
calculation. So we do relocate the FDT string section to a
block-boundary and enlarge the FIT image to end at this boundary +
BLOCKSIZE / 2. This way, both the broken as well as correct calculations
do expect the rootfs-header at the same position.
It is worth noting, that this is a rare edge-case in which only happens
if the image-length as well as the start of the string-section are not
placed in the same erase-block. This is an edge-case which happens very
rarely (thus it was not spotted prior).
Affected:
- U-Boot 2012.07 (Jun 16 2016 - 11:59:37)
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit
de59fc45402ff03e320264c8204f6928090534ad)
Mieczyslaw Nalewaj [Sun, 5 May 2024 21:45:36 +0000 (23:45 +0200)]
ramips: samknows whitebox v8: set wifi frequency
Set the 2.4GHz frequency for WiFi.
Fixes: #15391
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
(cherry picked from commit
1a2fc49b711fdde5d74aacd044ddf51f099c2e16)
David Bauer [Sat, 1 Jun 2024 14:52:20 +0000 (16:52 +0200)]
mpc85xx: add label-mac for HP MSM460
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit
dbc9596c7e60c26fc45eaa3d58ce5806e5589650)
David Bauer [Thu, 30 May 2024 00:27:50 +0000 (02:27 +0200)]
mpc85xx: add support for Hewlett Packard MSM460
Hardware
--------
CPU: Freescale P1020 2xe500 PPC
RAM: 256M DDR3 (Micron MT41J64M16JT-15E:G "D9MNJ")
NAND: 128M (Micron 2CA1)
BTN: 1x Reset
LED: Power - ETH - Radio1 - Radio2
UART: RJ-45 Cisco Pinout - 115200 8N1
Installation
------------
NOTE: You can find a repo with up-to-date instructions as well as
the required files here:
https://github.com/blocktrron/msm460-flashing
Required files
==============
You need a command-files as well as a U-Boot image.
The command-file has the following content (padded to 131072 bytes).
If you copy paste these, remove the newlines!
```
U-BOOT setenv ethaddr 02:03:04:05:06:07; setenv ipaddr 192.168.1.1;
setenv serverip 192.168.1.66; tftpboot 0x3000000 msm460-uboot.bin;
nand device; nand erase 0 0xC0000; nand write 0x3000000 0x0 0xC0000; reset
```
You can download the required U-Boot from this repository:
https://github.com/blocktrron/u-boot-msm/releases
Preparation
===========
Prepare a TFTP server serving two files:
- U-Boot NAND image as `msm460-uboot.bin`.
- OpenWrt factory image as `msm460-factory.bin`
- Command-file names `commands.tftp`
You can start a TFTP server in the current directory using dnsmasq:
```bash
sudo dnsmasq --no-daemon --listen-address=0.0.0.0 \
--port=0 --enable-tftp=enxd0 --tftp-root="$(pwd)" \
--user=root --group=root
```
Replace `enxd0` with the name of your network interface.
Procedure
=========
1. Assign yourself the IP-Address 192.168.1.66/24.
3. Connect the Router to the PC while keeping the reset button
pressed.
4. The LEDs will eventually begin to flash.
They will start to flash faster after around 15 seconds.
5. Release the reset button.
6. Start a new shell
7. Make sure you are currently in the directory where the tftp server
is located.
8. Run the following command:
```bash
tftp 192.168.1.1 -m binary -c put commands.tftp nflashd.
cccc9999
```
You get the message "Transfer timed out."
To find out if you have been successful, please check the
blinking LED Pattern.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit
af329ec38980e2f706411a11b9f344a62eb0dd8f)
Signed-off-by: David Bauer <mail@david-bauer.net>
Yanase Yuki [Thu, 7 Mar 2024 08:31:34 +0000 (17:31 +0900)]
gettext-full: link libiconv when building host pkg
On Fedora 40 system, some compile error happens when
building iconv-ostream.c. Linking to libiconv-full
fixes this.
Signed-off-by: Yanase Yuki <dev@zpc.st>
(cherry picked from commit
63dd14b906e9eb27bc878b95ac6777a3624b1135)
Link: https://github.com/openwrt/openwrt/pull/15627
Signed-off-by: Robert Marko <robimarko@gmail.com>
Rodrigo Balerdi [Fri, 10 May 2024 06:35:43 +0000 (03:35 -0300)]
ipq806x: rt4230w-rev6: fix status reporting via the LEDs
There is a custom LED controller between the 3 SoC GPIO outputs and
the red and blue LEDs of the device. It implements a strange mapping
that includes fixed, flashing, and breathing modes.
The current DTS configuration causes OpenWrt to flash the LEDs over
the controller's own flashing, resulting in chaotic output in boot,
failsafe, and upgrade modes.
This change fixes the LEDs in the best way possible as long as each
OpenWrt running state is limited to be signaled by a single led.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15440
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit
0868268c9fd4397411e9629eedda35b1547e798e)
Nick Hainke [Mon, 12 Feb 2024 22:48:46 +0000 (23:48 +0100)]
libxml2: update to 2.12.5
Release Notes:
https://gitlab.gnome.org/GNOME/libxml2/-/releases/v2.12.5
Fixes: CVE-2024-25062
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry picked from commit
c47b7571f0f874c746c5823f5e4d0f1b9b932697)
Nick Hainke [Wed, 24 Jan 2024 12:09:40 +0000 (13:09 +0100)]
libxml2: update to 2.12.4
Release Notes:
- https://gitlab.gnome.org/GNOME/libxml2/-/releases/v2.12.4
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry picked from commit
d82930c7c776d974e717ec958ca0c1019fea3b8f)
Nick Hainke [Wed, 3 Jan 2024 23:30:57 +0000 (00:30 +0100)]
libxml2: update to 2.12.3
Release Notes:
- https://gitlab.gnome.org/GNOME/libxml2/-/releases/v2.12.2
- https://gitlab.gnome.org/GNOME/libxml2/-/releases/v2.12.3
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry picked from commit
08ad3c963377ee853f87935929d33f19e5e34ef9)
Nick Hainke [Mon, 4 Dec 2023 16:03:21 +0000 (17:03 +0100)]
libxml2: update to 2.12.1
Release Notes:
- https://gitlab.gnome.org/GNOME/libxml2/-/releases/v2.12.0
- https://gitlab.gnome.org/GNOME/libxml2/-/releases/v2.12.1
Remove patch:
- 010-iconv.patch
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry picked from commit
2963e1687bcc6b54737f8fd519726eb45c17abb9)
Nick Hainke [Thu, 12 Oct 2023 04:23:02 +0000 (06:23 +0200)]
libxml2: update to 2.11.6
Release Notes:
- https://gitlab.gnome.org/GNOME/libxml2/-/releases/v2.11.5
- https://gitlab.gnome.org/GNOME/libxml2/-/releases/v2.11.6
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry picked from commit
62277c485e79f6fe453a8a1bd54f271ae17c7490)
Luis Mita [Tue, 7 May 2024 15:48:37 +0000 (11:48 -0400)]
mediatek: add support for Cudy TR3000 v1
Hardware:
- SoC: MediaTek MT7981B
- CPU: 2x 1.3 GHz Cortex-A53
- Flash: 128 MiB SPI NAND
- RAM: 512 MiB
- WLAN: 2.4 GHz, 5 GHz (MediaTek MT7976CN, 802.11ax)
- Ethernet: 1x 10/100/1000/2500 Mbps RTL8221B WAN, 1x10/100/1000 Mbps MT7981 LAN
- USB 3.0 port
- Buttons: 1 Reset button, 1 slider button
- LEDs: 1x Red, 1x White
- Serial console: internal test points, 115200 8n1
- Power: 5 VDC, 3 A
MAC addresses:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| WAN | 80:af:ca:xx:xx:x1 | label+1 |
| LAN | 80:af:ca:xx:xx:x0 | label |
| WLAN 2g | 80:af:ca:xx:xx:x0 | label |
| WLAN 5g | 82:af:ca:xx:xx:x0 | |
+---------+-------------------+-----------+
Installation:
The installation must be done via TFTP by disassembling the router. On other occasions Cudy has distributed intermediate firmware to make installation easier, and so I recommend checking the Wiki for this device if there is a more convenient solution than the one below.
To install using TFTP:
1. Connect to UART.
2. With the router off, press the RESET button. While the router is turning on, the button should continue to be pressed for at least 5 seconds.
3. A u-boot shell will automatically open.
4. Connect to LAN and set your IP to 192.168.1.88/24. Configure a TFTP server and an OpenWrt initramfs-kernel.bin firmware file.
5. Run these steps in u-boot using the name of your file.
setenv bootfile initramfs-kernel.bin
tftpboot
bootm
6. If you can reach LuCI or SSH now, just use the sysupgrade image with the 'Keep settings' option turned off.
Signed-off-by: Luis Mita <luis@luismita.com>
(cherry picked from commit
63b8d98dd0d2f7797ea5b5f25978590982bbbb5d)
Hank Moretti [Mon, 28 Aug 2023 15:45:05 +0000 (15:45 +0000)]
mediatek: fix sysupgrade error for WR30U
The NMBM-Enabled layout did not use fit image,
it just need default process. So it was been removed in platform.sh.
It will fix sysupgrade error for xiaomi,mi-router-wr30u-112m-nmbm.
Signed-off-by: Hank Moretti <mchank9999@gmail.com>
(cherry picked from commit
02214ab8dce59ee6b599f8dfdacb0297dc5dcc24)
Chuanhong Guo [Tue, 23 Jan 2024 11:20:47 +0000 (19:20 +0800)]
mediatek: drop NMBM layout for Xiaomi WR30U
This reverts commit
dcdcfc15115a1038e90f21f5aa41726d9c7e2fe5.
This is a firmware for third-party u-boot mod, which should not
be carried here by us.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
(cherry picked from commit
1b7e62b20b1735fcdc498a35e005afcd775abcf4)
Dim Fish [Mon, 27 Nov 2023 09:01:34 +0000 (12:01 +0300)]
mediatek: filogic: add support for Xiaomi AX3000T
**SoC**: MediaTek MT7981B 2x A53
**Flash**: ESMT F50L1G41LB 128MB
**RAM**: NT52B128M16JR-FL 256MB
**Ethernet**: 4x 10/100/1000 Mbps
**Switch**: MediaTek MT7531AE
**WiFi**: MediaTek MT7976C
**Buttons**: Reset, Mesh
**Power**: DC 12V 1A
1. Get ssh access. Supported stock firmware **1.0.47**
```
curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0Anvram%20set%20ssh_en%3D1%0A"
curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0Anvram%20commit%0A"
curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0Ased%20-i%20's%2Fchannel%3D.*%2Fchannel%3D%22debug%22%2Fg'%20%2Fetc%2Finit.d%2Fdropbear%0A"
curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0A%2Fetc%2Finit.d%2Fdropbear%20start%0A"
curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=********/api/misystem/arn_switch" -d "open=1&model=1&level=%0Apasswd%20-d%20root%0A
```
2. Backup stock partitions
```
nanddump -f /tmp/BL2.bin /dev/mtd1
nanddump -f /tmp/Nvram.bin /dev/mtd2
nanddump -f /tmp/Bdata.bin /dev/mtd3
nanddump -f /tmp/Factory.bin /dev/mtd4
nanddump -f /tmp/FIP.bin /dev/mtd5
nanddump -f /tmp/ubi.bin /dev/mtd8
nanddump -f /tmp/KF.bin /dev/mtd12
```
Then transfer them to your computer in a safe place.
3. Get firmware information `cat /proc/cmdline`
4. Copy openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-initramfs-factory.ubi to **/tmp** and flash
If **firmware=0**
```
ubiformat /dev/mtd9 -y -f /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-initramfs-factory.ubi
nvram set boot_wait=on
nvram set uart_en=1
nvram set flag_boot_rootfs=1
nvram set flag_last_success=1
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
reboot
```
If **firmware=1**
```
ubiformat /dev/mtd8 -y -f /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-initramfs-factory.ubi
nvram set boot_wait=on
nvram set uart_en=1
nvram set flag_boot_rootfs=0
nvram set flag_last_success=0
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
reboot
```
Then reboot your router, it should boot to the OpenWrt initramfs system now.
5. Flash openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-squashfs-sysupgrade.bin
`sysupgrade -n /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-squashfs-sysupgrade.bin`
1. Flash openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb
`ubiformat /dev/mtd8 -y -f /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb`
`reboot`
2. Install kmod-mtd-rw
`opkg update && opkg install kmod-mtd-rw`
`insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1`
3. Format ubi and create new ubootenv volume
```
ubidetach -p /dev/mtd8; ubiformat /dev/mtd8 -y; ubiattach -p /dev/mtd8
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
```
4. *(Optional **-10Mb** free space) Add recovery boot feature.*
```
ubimkvol /dev/ubi0 -n 2 -N recovery -s 10MiB
ubiupdatevol /dev/ubi0_2 /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb
```
5. Flash Openwrt U-Boot
```
mtd write /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-preloader.bin BL2
mtd write /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-bl31-uboot.fip FIP
```
6. Flash openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-squashfs-sysupgrade.itb
`sysupgrade -n /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-squashfs-sysupgrade.itb`
1. Force flash openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb
`sysupgrade -F -n /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb`
2. Format ubi and Nvram
```
ubidetach -p /dev/mtd8; ubiformat /dev/mtd8 -y; ubiattach -p /dev/mtd8
mtd erase Nvram
```
3. Install kmod-mtd-rw
`opkg update && opkg install kmod-mtd-rw`
`insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1`
4. Flash stock images from backup
```
mtd write /tmp/BL2.bin BL2
mtd write /tmp/FIP.bin FIP
mtd write /tmp/ubi.bin ubi
```
Then reboot your router, waiting it finished rollback in minutes.
`ubiformat /dev/mtd7 -y -f /tmp/ubi.bin`
Then reboot your router, waiting it finished rollback in minutes.
Signed-off-by: Dim Fish <dimfish@gmail.com>
(cherry picked from commit
7dbcc1215a56cc1da68c81bf92d7efa174c5e051)
Paul Geraedts [Sat, 24 Feb 2024 08:01:01 +0000 (09:01 +0100)]
mediatek: filogic: fix failsafe mode on devices with no lan1
Default to lan4 port, instead of (missing) lan1 port,
to fix failsafe mode on Xiaomi AX3000T, WR30U, AX6000
Build system: x86/64
Build-tested: mediatek/filogic/xiaomi_mi-router-ax3000t-ubootmod
Run-tested: mediatek/filogic/xiaomi_mi-router-ax3000t-ubootmod
Signed-off-by: Paul Geraedts <p.f.j.geraedts@gmail.com>
(cherry picked from commit
8256d06933e7542ecdd427b6a0ef4e87bb37d3f4)
Alexandru Gagniuc [Wed, 3 Apr 2024 19:32:08 +0000 (14:32 -0500)]
wifi-scripts: fix creation of IBSS in legacy (non-HT) mode
When an IBBS interface is configured for IBSS legacy mode, wdev.htmode
is empty. This is empty string results in an empty positional argument
to the "ibbs join" command, for example:
iw dev phy0-ibss0 ibss join crymesh 2412 '' fixed-freq beacon-interval 100
This empty argument is interpreted as an invalid HT mode by 'iw',
causing the entire command to fail and print a "usage" message:
daemon.notice netifd: radio0 (4527): Usage: iw [options] \
dev <devname> ibss join <SSID> <freq in MHz> ...
Although nobody will ever need more than 640K of IBSS, explicitly use
"NOHT" if an HT mode is not given. This fixes the problem.
Fixes: e56c5f7b276a ("hostapd: add ucode support, use ucode for the main ubus object")
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [extend to cover more cases]
(cherry picked from commit
cee9fcdb7350911f474544189817d25fd4070111)
Rany Hany [Sun, 5 May 2024 22:39:58 +0000 (01:39 +0300)]
mediatek: fix broken PCIe caused by update to 5.15.158
The patch "710-pci-pcie-mediatek-add-support-for-coherent-DMA.patch"
makes use of "syscon_regmap_lookup_by_phandle" which requires that
"syscon" be in the compatible list.
Without this patch, PCIe probe will fail with the following error:
[ 1.287467] mtk-pcie
1a143000.pcie: host bridge /pcie@
1a143000 ranges:
[ 1.294019] mtk-pcie
1a143000.pcie: Parsing ranges property...
[ 1.299901] mtk-pcie
1a143000.pcie: MEM 0x0020000000..0x0027ffffff -> 0x0020000000
[ 1.307954] mtk-pcie
1a143000.pcie: missing hifsys node
[ 1.313185] mtk-pcie: probe of
1a143000.pcie failed with error -22
Fixes: 01c58a0d2a ("kernel: bump 5.15 to 5.15.158")
Signed-off-by: Rany Hany <rany_hany@riseup.net>
(cherry picked from commit
8607372b410fbb24b08de97ff5941341d0870d6f)
Christian Marangi [Wed, 22 May 2024 10:41:10 +0000 (12:41 +0200)]
tools: refresh all patches
Refresh all tools patches now that tools/refresh correctly works.
CI now checks for them and actively complain if tools have unrefreshed
patches.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Mon, 25 Sep 2023 00:29:31 +0000 (02:29 +0200)]
quilt.mk: don't error on refresh/update if patches doesn't exist
The current code fails if we have package or host tools with no patches
to apply. The error printend is the following: (taking ubus as an
example)
make[2]: Entering directory '/home/ansuel/openwrt-ansuel/openwrt/scripts/config'
make[2]: 'conf' is up to date.
make[2]: Leaving directory '/home/ansuel/openwrt-ansuel/openwrt/scripts/config'
make[1]: Entering directory '/home/ansuel/openwrt-ansuel/openwrt'
make[2]: Entering directory '/home/ansuel/openwrt-ansuel/openwrt/package/system/ubus'
The source directory contains no quilt patches.
make[2]: *** [Makefile:81: quilt-check] Error 1
make[2]: Leaving directory '/home/ansuel/openwrt-ansuel/openwrt/package/system/ubus'
time: package/system/ubus/refresh#0.06#0.00#0.07
ERROR: package/system/ubus failed to build.
make[1]: *** [package/Makefile:120: package/system/ubus/refresh] Error 1
make[1]: Leaving directory '/home/ansuel/openwrt-ansuel/openwrt'
make: *** [/home/ansuel/openwrt-ansuel/openwrt/include/toplevel.mk:232: package/ubus/refresh] Error 2
We exit 1 after saying that there are no patches because later in the
function quilt pop fails to execute.
Having no patches for a package and calling refresh should not be
a critical error and the function should just do nothing.
To handle this improve quilt.mk with the following addition.
- If we don't have any patch for the package, we print a warning and we
create an empty series. This is useful to trick quilt and make it do
nothing.
We also create a status file .quilt_no_patch to detect in the other
function that we don't have patches to handle.
- In refresh makefile target, we check if .quilt_no_patch exist and
we skip quilt cleanup if this exist.
- In RefreshDir function we change the logic and now we delete the
patches directory and not only the content. This is done as a cleanup
to clean case with empty patches directory.
- In RefreshDir we check if .quilt_no_patch exist and we skip creating
the patches directory and copying the refreshed patches.
- In RefreshDir we delete at the end any trace of .quilt_no_patch if
present.
This is needed to support run like package/refresh that will run the
refresh process on any package present in the buildroot.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit
9536446965e853231e34c4e5dc4cf13f838b9e90)
Christian Marangi [Mon, 25 Sep 2023 00:26:43 +0000 (02:26 +0200)]
quilt.mk: use CURDIR instead of ./ for PATCH_DIR and FILES_DIR
To better reference them for diagnostic use, reference the PATCH_DIR and
FILES_DIR with the absolute path instead of using ./ and reference by
the relative location.
No behaviour change intended.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit
bb1bfb46020b38179ef97d30333c90ab00b71c97)
Christian Marangi [Wed, 22 May 2024 09:56:45 +0000 (11:56 +0200)]
tools/padjffs2: use Host/Prepare/Default instead of raw commands
Now that Host/Prepare/Default is always defined, we can use that instead
of using raw commands to move files from the src directory to
HOST_BUILD_DIR.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit
01048c7456785bc4a45452c84d8f31635e1fa60b)
Christian Marangi [Wed, 22 May 2024 09:53:52 +0000 (11:53 +0200)]
tools/missing-macros: install files from HOST_BUILD_DIR instead of src
Install files from HOST_BUILD_DIR instead of src. These files are now
correctly copied to HOST_BUILD_DIR and can be referenced from there.
(cherry picked from commit
46bcbe42236bbe058eaeb89a0d1a4f22926cfdf9)
[ rebased on top of openwrt-23.05 ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Wed, 22 May 2024 09:38:49 +0000 (11:38 +0200)]
host-build: always define Host/Prepare/Default
We currently skip defining Host/Prepare/Default if HOST_UNPACK is not
defined.
This is mostly the case for Host packages that just provide files with
the src directory and don't need to be downloaded/extracted.
This was probably done lots of times ago due to quilt causing error as
the patches directory wasn't present.
This has changed now and quilt can correctly detect if no patches needs
to be applied (instead of terminating with error)
Always define Host/Prepare/Default to make tools/refresh correctly works
as HOST_QUILT is hardcoded enabled for this make target and will
complain for tool not prepared for quilt patches.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit
725389b7c745b0fa68426986c9bca14171f16887)
Yuu Toriyama [Sat, 18 May 2024 22:08:37 +0000 (07:08 +0900)]
wireless-regdb: update to 2024.05.08
Changes:
73529a8 Revert "wireless-regdb: Update and disable 5470-5730MHz band according to TPC requirement for Singapore (SG)"
87941e4 wireless-regdb: Update regulatory rules for Taiwan (TW) on 6GHz
33797ae wireless-regdb: update regulatory database based on preceding changes
Signed-off-by: Yuu Toriyama <PascalCoffeeLake@gmail.com>
(cherry picked from commit
65c1f0d433e89c794a6d22dbe474666c241f9e7b)
Rafał Miłecki [Sat, 18 May 2024 12:56:58 +0000 (14:56 +0200)]
mt76: fix mt7603 compilation
This fixes:
mt7603/dma.c: In function 'mt7603_rx_loopback_skb':
mt7603/dma.c:60:17: error: ISO C90 forbids mixed declarations and code [-Werror=declaration-after-statement]
Fixes: 2568b30285ff ("mt76: backport mt7603 fixes important for its stability")
Fixes: https://github.com/openwrt/openwrt/issues/15510
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Robert Marko [Thu, 16 May 2024 10:03:19 +0000 (12:03 +0200)]
ipq806x: mr42/mr52: fix PCIe ports
All three PCIe ports are reported non working on Meraki MR42/MR52 boards
since kernel 6.1 with the issue of PCIe PHY link never coming up thus
no WLAN cards are available on the boards.
After debugging it seems that PCIe worked on 5.15 and older purely by
accident as device DTS was using /delete-property/ perst-gpios; in each
of the 3 PCIe nodes but there was no "perst-gpios" property in the SoC DTSI
as it was still using the older "perst-gpio" property so it was not getting
removed from the device DTS.
However, in kernel 6.1 commit ("ARM: dts: qcom-*: replace deprecated
perst-gpio with perst-gpios") updated all Qualcomm DTS-es to use the newer
"perst-gpios" and thus once ipq806x moved to 6.1 PCIe stopped working as
now that property was being dropped from the device DTS.
So, since the removal of PERST pins seems to have been wrong from the start
lets drop the property removal from MR42/MR52.
Fixes: #15408
Link: https://github.com/openwrt/openwrt/pull/15509
Link: https://github.com/openwrt/openwrt/pull/15512
Signed-off-by: Robert Marko <robimarko@gmail.com>
Rafał Miłecki [Thu, 16 May 2024 12:11:24 +0000 (14:11 +0200)]
mt76: backport mt7603 fixes important for its stability
Those are required for stable MT7603E & on-SoC MT7628/MT7688 wireless
support. After mt76 receiving more testing we may just update codebase
and drop those backports.
Fixes: https://github.com/openwrt/mt76/issues/865
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Felix Fietkau [Thu, 16 May 2024 12:06:12 +0000 (14:06 +0200)]
mt76: update to Git HEAD (2024-02-03)
a9693e1979c2 linux-firmware: add firmware for MT7996
0258dc90e3a1 wifi: mt76: mt7603: fix reading target power from eeprom
3e81173d9e2b wifi: mt76: mt7603: initialize chainmask
786a339bac36 wifi: mt76: mt7996: fix fortify warning
bc37a7ebc267 wifi: mt76: mt7996: fix fw loading timeout
027bab6a88a3 wifi: mt76: usb: create a dedicated queue for psd traffic
e8909c610c3b wifi: mt76: usb: store usb endpoint in mt76_queue
8b3d96fa4ead wifi: mt76: mt792xu: enable dmashdl support
7864d7ad0ed0 wifi: mt76: mt76x2u: add netgear wdna3100v3 to device table
27c81f7c1480 wifi: mt76: mt7925: fix connect to 80211b mode fail in 2Ghz band
b7443c63069a wifi: mt76: mt7925: fix SAP no beacon issue in 5Ghz and 6Ghz band
bab721a65f5a wifi: mt76: mt7925: fix mcu query command fail
1f0f71ed81e8 wifi: mt76: mt7925: fix wmm queue mapping
bcfe2ad966f3 wifi: mt76: mt7925: fix fw download fail
f982c3d67a29 wifi: mt76: mt7925: fix WoW failed in encrypted mode
6a72716ec213 wifi: mt76: mt7925: fix the wrong header translation config
50928b7e1359 wifi: mt76: mt7925: add flow to avoid chip bt function fail
762ab4530e8f wifi: mt76: mt7925: add support to set ifs time by mcu command
87deaf82efa4 wifi: mt76: mt7925: update PCIe DMA settings
c190c1576522 wifi: mt76: mt7925: support temperature sensor
025d5734caba wifi: mt76: mt7996: check txs format before getting skb by pid
4768bfa2baca wifi: mt76: mt7996: fix TWT issues
a65e3eced907 wifi: mt76: mt7996: disable AMSDU for non-data frames
d71716d93aee wifi: mt76: mt7996: fix incorrect interpretation of EHT MCS caps
f21728f3f4bd wifi: mt76: mt7996: ensure 4-byte alignment for beacon commands
68dad7dacd2a wifi: mt76: mt7996: fix HE beamformer phy cap for station vif
66a28f340cdc wifi: mt76: mt7996: mark GCMP IGTK unsupported
b47ad8a7764e wifi: mt76: mt7996: fix efuse reading issue
c2fc7dae7b72 wifi: mt76: mt7996: remove TXS queue setting
e0f1ed168ed5 wifi: mt76: mt7996: add locking for accessing mapped registers
d0cc92c1fd08 wifi: mt76: connac: set correct muar_idx for mt799x chipsets
ae0c62279adc wifi: mt76: mt7996: fix HIF_TXD_V2_1 value
ecc14276af54 wifi: mt76: mt792x: fix ethtool warning
9827df56b241 wifi: mt76: move wed common utilities in wed.c
dccbd2598505 wifi: mt76: mt7925: fix the wrong data type for scan command
9907f4f20261 wifi: mt76: mt792x: add the illegal value check for mtcl table of acpi
1b088a7ac06d wifi: mt76: mt7921e: fix use-after-free in free_irq()
f3c5b4820d7f wifi: mt76: mt7925e: fix use-after-free in free_irq()
d75eac9f5531 wifi: mt76: mt7921: fix incorrect type conversion for CLC command
7bd5401f5bb1 wifi: mt76: mt792x: fix a potential loading failure of the 6Ghz channel config from ACPI
ea55196bc4a0 wifi: mt76: mt792x: update the country list of EU for ACPI SAR
6124ea9135ed wifi: mt76: mt7921: fix the unfinished command of regd_notifier before suspend
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit
114190d8ae61fb3a7671852fbd7f0ca3279a5625)
[rmilecki: add patches/fixes for regressions from this commit]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Felix Fietkau [Thu, 16 May 2024 12:06:06 +0000 (14:06 +0200)]
mt76: update to Git HEAD (2024-01-18)
83e3947e2c52 linux-firmware: update firmware for MT7922 WiFi device
ddaa8cb6e81a linux-firmware: update firmware for MT7921 WiFi device
f83b1601cc10 linux-firmware: update firmware for MT7922 WiFi device
61d334ab0f33 linux-firmware: add firmware for MT7925
a7836e4c8a60 wifi: mt76: disable HW AMSDU when using fixed rate
a8571ebbcd95 wifi: mt76: check txs format before getting skb by pid
3d5890e2cab3 wifi: mt76: mt7915: fix error recovery with WED enabled
703c26d01197 wifi: mt76: mt7915: add locking for accessing mapped registers
f77188160441 wifi: mt76: mt7915: update mt798x_wmac_adie_patch_7976
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit
a28cedbdab96be9bee39bb70098a1508c0252a8a)
projects / openwrt / staging / pepe2k.git / log