ath79: meraki-mr18: fix initramfs build

Now, that initramfs images built for ZTE devices work, by moving
LZMA_TEXT_START further up the available RAM - same fix works
successfully for Meraki MR18 too. Apply it and reenable initramfs
generation again.

Fixes: 1d49310fdb5e ("ath79: add Cisco Meraki MR18")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17680
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 7423e67e1b8c7e4c9f527d1300dbeaab72b1f95f)

mediatek: Xiaomi AX3000t: fix soft brick for the rd23 model

This commit fixes Xiaomi AX3000t soft bricks. Issue affects at least rd23
model (Global version) users:
Link: https://forum.openwrt.org/t/openwrt-support-for-xiaomi-ax3000t/180490/452
I also found that these nvram settings are wrong for the rd23 model and
U-Boot erase them:
'''
flag_try_sys1_failed 8
flag_try_sys2_failed 8
'''
As a result, platform.sh -> xiaomi_initial_setup() function sometimes ends
early without applying settings for the rd23 model.

RD03 model strategy:
1. Don't touch values those were set up by platform.sh ->
xiaomi_initial_setup() function

RD23 model strategy:
1. Apply correct nvram settings at every boot
2. Use bulk fw_setenv call

I didn't find opened issue for AX3000t. Similar AX3200 issue:
Link: https://github.com/openwrt/openwrt/issues/16347
So, other Xiaomi devices (e.g. Xiaomi WR30U) may also require fix.

Fixes: 7dbcc1215a56cc1da68c81bf92d7efa174c5e051 ("mediatek: filogic: add support for Xiaomi AX3000T")
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17580
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 42a253c7e8992e2274628b1770a0263ac433d0bc)

mediatek: replace multiple fw_setenv calls by the bulk one

This commit replaces multiple fw_setenv calls by the bulk one to reduce
flash writes.

Thanks @Linaro1985 for the idea.

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17580
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit a6b0abf4661e4dc1449494e46340f75c44df81de)

kernel: bump 6.6 to 6.6.72

Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.72

Dropped to due being superseded by upstream patch:
mediatek/patches-6.6/870-drm-mediatek-only-touch-DISP_REG_OVL_PITCH_MSB-if-AF.patch[1]

All other patches automatically rebased.

1. https://github.com/gregkh/linux/commit/ac7f5641e9887354a0fc6f48190533af084bb0dc

Build system: x86/64
Build-tested: bcm27xx/bcm2712, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Run-tested: bcm27xx/bcm2712, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/17646
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 1d021458fd681dc4c27615a574cc09cc57d1c51e)

lantiq: xrx200: fb7430 set correct label-mac

the CWMP account mac is correctly set on the lan device but was not correctly as label-mac

Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/17618
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit f9813f41b2e9fccb644ae149eabe575fbae12fa3)

lldpd: fix config for build without LLDP-MED

The lldp_class and lldp_location config option are only valid when
compiled with LLDP-MED support. If not they will cause lldpd not to
start.

Signed-off-by: Sebastian Pflieger <sebastian@pflieger.email>
Link: https://github.com/openwrt/openwrt/pull/17571
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 2c22d7c3a4a7edcce1af656c8cddb1ab163e3d02)

lldpd: reset PKG_RELEASE

lldpd was updated, so reset PKG_RELEASE after the PKG_VERSION update.

Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit abbec429b40f149f9c5a99a64ee7bf4e804fbb7d)

lldpd: bump version to 1.0.18

Changes (breaking):
- Remove support for building 802.3bt TLVs (broken).

Fix:
- Fix memory leaks in EDP/FDP decoding when receiving some TLVs twice.
- Do not set interface description continuously.
- Use a different Netlink socket for changes and queries.

Signed-off-by: Sebastian Pflieger <sebastian@pflieger.email>
Link: https://github.com/openwrt/openwrt/pull/17570
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit a18385041eaeaf6d98ab79a30ce5fba4e712b765)

d1: Use correct module for devices with wifi

Devices with wifi (LicheePi RV and MangoPi MQ Pro) were using the
wrong module.  Also wpad was missing to enable using the WiFi.

Signed-off-by: Raylynn Knight <rayknight@me.com>
Link: https://github.com/openwrt/openwrt/pull/17576
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
(cherry picked from commit 8a17bae722a62954269f29dc48025e88c919dc24)

uci: update to Git HEAD (2025-01-20)

047b2efc1348 CMakeLists.txt: bump minimum cmake version
16ff0badbde7 CMakeLists: add support for including ABIVERSION in the library version number

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit e046f8c318618162fcdd768c4a9eadd53c239629)

mediatek-filogic: fix wax220 wifi leds

The WAX220 does have a 2.4GHz and 5GHz wifi led, which was set to trigger on netdev before.
This commit changes this to trigger on activity of the respective radio

Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/17627
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 99431e315039d7f9689b21a8aa220adadf52a886)

ath79: zte-mf28x-common: fix initramfs execution

Now that LZMA_TEXT_START is configurable per-target once again,
move the target above 32MB boundary for ZTE MF28* devices.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17616
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 32c6b9064ac7fc62cead37b1bc7d46ffba598c71)

ath79: lzma-loader: expose LZMA_TEXT_ADDRESS configuration again

initramfs for some devices grew so big, that it can't be loaded within
the previous 32MB RAM limit. Make the LZMA_TEXT_ADDRESS configurable
per-target once again, to fix it for bigger devices, while maintaining
compatibility with previous ones.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17616
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 6720958659d226e71dca49657202e0502bb059bd)

mediatek: EX5601-T0 add Zyxel EX5601-T1 and T-56 alias

Define EX5601-T1 and T-56 as alternative name, to explicitly show
the device is supported using existing image. EX5601-T1 does not
have the option to switch between WAN/SFP port. The switch port
is hardwired to the WAN port. The Zyxel T-56 is the odido-branded
version of the EX5601-T1.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/17615
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 3d63a41ffab69cb6f49c14cff99c3c3a84899363)

kernel: fix rootfs initramfs not updating on subsequent single build

There is currently a problem where the rootfs in an initramfs image for
single target build is not updated on subsequent run. This is caused by
a bug introduced in d78dec3e19e3 ("kernel: copy kernel build dir on
Per-Device Initramfs compilation") where the initramfs_data.cpio rm was
moved to PrepareConfigPerRootfs. This caused the side effect of dropping
the rm call for single target build making the kernel reusing the
previous generated initramfs_data.cpio.

To correctly handle this, restore the original location of this call
right after the touch /init call. This way the kernel will always
regenerate the initramfs embedded rootfs ALSO for single target build.

Fixes: d78dec3e19e3 ("kernel: copy kernel build dir on Per-Device Initramfs compilation")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 334c649a8d9b191c0282f9104b3997b090628f56)

fritz-tools: increase PKG_RELEASE

Increase PKG_RELEASE as follow-up for
("lantiq: fritz_cal_extract with reverse option for AVM FritzBox 7430").

Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 4a8717b5e76edbc8e1f63122f8b05685e0b779db)

lantiq: fritz_cal_extract with reverse option for AVM FritzBox 7430

This implementation of fritz_cal_extract can also retrieve firmware
data stored in reverse byte order, as found in the AVM 7430 device.

This is done by intermediate storage in a buffer presumably large enough
to hold the complete data set. Currently, this buffer size is 128kB + 1kB
(some extra space for skipped data).

In the usual case of "forward" data, this implementation should behave
like the original implementation in all common cases. limit [-l] will
determine the amount of data read and size of buffer allocated.

However, if you are reading reversed data or didn't set a limit, the buffer
may be too small to hold all data. In this case, you can choose a higher
limit [-l] to enforce a sufficient buffer size.

Signed-off-by: Dustin Gathmann <dzsoftware@posteo.org>
Link: https://github.com/openwrt/openwrt/pull/15501
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit b2cac2a9785ada7c30388349f5d9a9bdcff2e730)

ath79: add extended AR9344 reset sequence

According to datasheet, on AR9344 the switch and switch analog need to
be reset first before initiating a full reset.

Resetting these systems fixes spurious reset hangs on Atheros AR9344
SoCs.

Link: https://github.com/freifunk-gluon/gluon/issues/2904
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 144af32b47be6181f01815762159dff863f4616b)

Revert "ath79: reset ETH switch for AR9344"

This reverts commit 916af73fc388d638b1a717a2411792e0680dd8e6.

It was reported this change did not fix the reboot issues on AR9344.

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 937b5a3e0017f4f39c0f7727a910d2df78fc4ce9)

ipq4019: patch initialization of Lantiq DSL on FritzBox 7530.

Some VRX518 modems fail to initialize properly with the error message
"dc_ep_clk_on failed". As a result, the DSL data path doesn't work.

This hack, which is based on code from the FRITZ!Box 7530 GPL archive,
fixes the issue. It changes the PCIe vendor/device ID to values matching
a Lantiq SoC. It also appears to emulate a Lantiq CPU ID register for
connected PCIe devices, by remapping the matching address area to a
specially crafted buffer using the address translation unit.

A dedicated compatible is created to activate this in
the device tree, so this shouldn't affect any devices other than
FRITZ!Box 7530/7520.

Original investigation was done in https://github.com/janh/openwrt/commit/59f52125178146a9dc44290c11c63e5e029e8044 which used the "avm,host_magic" property to enabled the patch.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/17622
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 676dcb1b2cf84142a61d51a15e7a8e1bdc937c23)

ramips: mt7621: add support for Confiabits MT7621 v1

Hardware:
 - SoC: MediaTek MT7621DAT
 - Flash: 16 MiB cFeon
 - RAM: 128 MiB MT7621DAT
 - WLAN: 2.4 GHz (MT7603EN), 5 GHz (MT7613BEN 802.11ac)
 - Ethernet: 1x 10/100/1000 Mbps WAN, 3x 10/100/1000 LAN (MT7621DAT)
 - Buttons: 1 Reset button, 1 WPS button
 - LEDs: 5x Green (POWER/WAN/2.4G/5G/WPS), 1x Red (WAN)
 - Serial console: unpopulated header, 57600 8n1
 - Power: 12 VDC, 1 A

MAC:
LAN MAC: label mac (eeprom@4)
WAN MAC: label mac (eeprom@4)
2.4G MAC: label mac (eeprom@4)
5G MAC: label mac + 1 (eeprom@8004)

Installation:
The stock firmware is OpenWrt-based. If you can reach LuCI or SSH, just use the sysupgrade image
with the 'Keep settings' option turned off.

Signed-off-by: Luis Mita <luis@luismita.com>
Link: https://github.com/openwrt/openwrt/pull/17534
(cherry picked from commit 1c5ca24da6cd727f4fcb8edbe00fa66543a6c678)
Link: https://github.com/openwrt/openwrt/pull/17653
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

qualcommax: dl-wrx36: fix 2.5G port LED-s

Currently, 2.5G port LED-s on Dynalink are incorrectly configured and thus
they will light up all of the time.

So, lets fix this by:
1. Current green LED is actually yellow, change the color
2. Fix its polarity as its actually active-low
3. The yellow LED that was registered as being connected to LED_1 pin on
the PHY is not actually connected at all, so remove it.
4. The actual green LED is connected to LED_2 on the PHY so add it.

Fixes: 75ad5c24142a ("qualcommax: switch to qca8081 upstream PHY driver")
Fixes: #14502
Link: https://github.com/openwrt/openwrt/pull/17656
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 2d077913cd53cad33123c8a9bf6da8a1c5576c69)

generic: backport pending Realtek PHY patches

These patches have been accepted, so we can move them from pending to
backported.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 7924acdd63490aa436bf114d290cb56cd4eba008)

generic: add pending patches for RealTek Ethernet PHYs

Import patches to fix several issues with status reporting of RealTek
2.5G PHYs.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 41c164d32bedb6b27ad1fd022dec6d25338db6d6)

generic: backport Realtek PHY patches from upstream

Adds patches for the temperature sensor on RTL822x.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit d7e82c78d7a2a84404198dab8faf8e142939eb05)

generic: r8169: remove reverted temperature sensor patch

The patch adding temperature sensor support for r8169 has been removed upstream
and the functionality will be added to Realtek PHY instead:
https://github.com/torvalds/linux/commit/1f691a1fc4bef1c5cf5f503e14e1a22fc37c97e3

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 0de9999a7819acf74f6adeaa27be363cf72409ab)

airoha: an7581: add pending PCI patch

Add pending PCI patch that should correctly fix mediatek driver with
Airoha SoC.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit f22febae1a6b7c654eaf09ed02c0d0017be6d73a)

airoha: an7581: backport ETS patch for Airoha ethernet

Backport ETS patch for Airoha ethernet and refresh affected patches.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 67635578fd19d0576c54bbe722a9664e8a6ab2a6)

uci: update to Git HEAD (2025-01-17)

fb3c2343b17b add support for an override config directory

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 44c877f1973b923a2032ce9d880f496a2b077ef6)

uci: update to Git HEAD (2024-11-26)

10f7996ec294 file: Ignore config file with '.' in name

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 3929ef4c21844189d5db8d14e7e6dc6ba983d571)

mediatek: remove obsolete base-files scripts

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 48e1427ffa867bddc822a463af862b9dacc5bde8)

netifd: improve packet steering on ipq40xx (and possibly others)

Some platforms a single ethernet device for all ports with multiple rx rings
and NAPI threading enabled. In this case, the steering script was limiting
performance by keeping all NAPI threads assigned to the same CPU.
Fix this by assigning each rx queue and the corresponding NAPI task separately.
Additionally, if the number of rx queues is at least as big as the number of
CPUs, skip weight based assignment and distribute the load across all CPUs
directly.

Fixes: https://github.com/openwrt/openwrt/issues/17611
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit acce25b789d40f2d88a2326a7d9921bd1743fe54)

mvebu: WD Cloud Mirror Gen2: Remove stty dependency

The package coreutils-stty is not part of the OpenWrt main packages. A
board can not depend on it. Remove the dependency to fix a build problem
seen in the build bots.

Fixes: 8fb805aa1f25 ("mvebu: Add support for WD Cloud Mirror Gen2")
(cherry picked from commit 717f62d256ccb52549a24c256615b28440ed1a86)
Link: https://github.com/openwrt/openwrt/pull/17589
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

mvebu: Add support for WD Cloud Mirror Gen2

Hardware
--------
Marvell Armada 385 (MV88F6820)
512B RAM
256MB NAND (Hynix H27U2G8F2CTR)
1x 1Gbit
2x USB 3.0
2x SATA-III
UART: 115200 8N1 3.3V
RTC
Weltrend MCU WT6703F connected via UART1 for Power LED / PWM Fan / hw reset / WoL

Installation
------------
Connect UART 3.3V adapter to JP2  pins: 1-RX / 2-GND / 5-TX

Use USB2.0 FAT32 pendrive with openwrt-mvebu-cortexa9-wd_cloud-mirror-gen2-initramfs-kernel.bin
 1. stop boot by pressing 1
 2. usb start
 3. fatload usb 0:1  0x02000000 openwrt-mvebu-cortexa9-wd_cloud-mirror-gen2-initramfs-kernel.bin;bootm 0x02000000 -
 4. do backup mtd1 mtd3
 5. use sysupgrade

Or tftp
 1. stop boot by pressing 1
 2. setenv ethact egiga2;setenv serverip 192.168.11.114;setenv ipaddr 192.168.11.113
 3. tftpboot 0x02000000 openwrt-mvebu-cortexa9-wd_cloud-mirror-gen2-initramfs-kernel.bin; bootm 0x02000000 -
 4. do backup mtd1 mtd3
 5. use sysupgrade

or Evgeny Kolesnikov <evgenyz@gmail.com> method from his failed PR 2040

- Using original firmware's network settings obtain SSH access to the device.
- Put *-image-cfs-factory.bin and *-uImage-factory.bin images into device's /tmp directory.
- Write kernel (uImage) image 'flash_eraseall /dev/mtd1 && nandwrite --markbad -p /dev/mtd1 /tmp/*-uImage-factory.bin'.
- Write rootfs (image-cfs) image 'ubiformat /dev/mtd3 -f /tmp/*-image.cfs-factory.bin -y'.
- Reboot the device.

Installation (upgrade):

Use *-sysupgrade.bin in a usual way.
Weltrend MCU control is done via uart1 19200

stty -F /dev/ttyS1 raw speed 19200
stty -F /dev/ttyS1 raw speed 19200

PWM Fan Control
off: 00
echo -n -e '\xfa\x02\x00\x00\x00\x00\xfb' > /dev/ttyS1
slow: 5F
echo -n -e '\xfa\x02\x00\x5f\x00\x00\xfb' > /dev/ttyS1
max: FF
echo -n -e '\xfa\x02\x00\xff\x00\x00\xfb' > /dev/ttyS1

Power LED Control
Blue
echo -n -e '\xfa\x26\x00\x11\x00\x01\xfb' > /dev/ttyS1
Red
echo -n -e '\xfa\x26\x00\x14\x00\x01\xfb' > /dev/ttyS1
Orange
echo -n -e '\xfa\x26\x00\x12\x00\x01\xfb' > /dev/ttyS1

more here: https://github.com/c-MM/mcm-daemon/blob/master/mcm.h

Signed-off-by: Robert Senderek <robert.senderek@10g.pl>
Link: https://github.com/openwrt/openwrt/pull/17046
(cherry picked from commit 8fb805aa1f25b69b7849c8b1ce787ed47b16d123)
Link: https://github.com/openwrt/openwrt/pull/17589
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

armsr: change image names to 'combined-efi'

luci-app-attendedsysupgrade expects images to be named
'combined-efi' when the system is using EFI images.

This came about as x86 has 'combined' images for legacy
(BIOS) boot and 'combined-efi' for EFI systems.

armsr images were originally named 'combined' only
as there was no 'legacy' image type.

To avoid special handling in the attendedsysupgrade
code, name EFI images consistent with other targets.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
Link: https://github.com/openwrt/luci/pull/6430
Link: https://github.com/openwrt/openwrt/pull/12963
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit c9ebd4fb30773ca55cc2da6b2c1962046a2e0fff)

netifd: fix napi process name matching in packet steering script

Fixes CPU usage imbalance on some devices using threaded NAPI

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 67a4aeef6c63e5836bd6b82faf6cc15934869efb)

wifi-scripts: allow per-IF mesh basic rate selection

Bringing up a mesh interface using wpa_supplicant already supports a
per-VIF basic rate selection. Add the same ability when creating a mesh
VIF without wpa_supplicant.

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 3deeb7805f69f54b9ab20c0e12f8dd916fec4de1)

wifi-scripts: remove leftover legacy (non-netifd) wifi script support

cfg80211 is the only supported wireless API

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit d1275392916522d664e710752c517246540cbf73)

wifi-scripts: add macaddr_base wifi-device option

This can be used to configure the base mac address from which all
interface mac addresses are derived

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 00860e485b2ef82c1fafc8e011f3a8965e317bca)

hostapd: fix processing mbssid config option

Do not strip the first character from the field name

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 59dd9cddf9e72d1f9b4ff7e01ae32d2fa99259d9)

wifi-scripts: add option to set per-device ifname prefix

Simplifies setting ifname to a different pattern for all affected
interfaces.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit a9ff3ba24b9466d9c06b9a9e1c2e9672bdd9f6f9)

mt76: update to Git HEAD (2025-01-14)

cf4e709e493a wifi: mt76: mt7996: fix crash in mt7996_set_radar_background
4c786fa52bb2 wifi: mt76: mt7915: fix register mapping
849923df3dde wifi: mt76: mt7996: fix register mapping
6be1dc9a1c79 wifi: mt76: mt7925: fix the unfinished command of regd_notifier before suspend
d33ea3cab72b wifi: mt76: mt7925: fix CLC command timeout when suspend/resume
5aacd0d73c80 wifi: mt76: mt7925: add handler to hif suspend/resume event
e86e97e45397 wifi: mt76: mt7925e: fix too long of wifi resume time
e43df6bf4892 wifi: mt76: mt7996: fix thermal sparse warning
02f453d8dfc8 wifi: mt76: fix survey regression
7279e3f3c3e0 wifi: mt76: mt7925: fix unused-but-set warning
49c0bd66da3b wifi: mt76: mt7996: fix unused-but-set variable
2c068c96382e wifi: mt76: fix crash in mt76_switch_vif_chanctx
731070da2c2a wifi: mt76: mt7996: add max mpdu len capability
99d8ed164a96 wifi: mt76: mt7996: fix the capability of reception of EHT MU PPDU
32ee924831ba wifi: mt76: mt7996: fix HE Phy capability
9b588c7fb333 wifi: mt76: mt7996: fix incorrect indexing of MIB FW event
46798905cf5a wifi: mt76: connac: adjust phy capabilities based on band constraints
5c50f6f7dafe wifi: mt76: mt7996: fix definition of tx descriptor
9cdb62dc084f wifi: mt76: mt7996: fix ldpc setting
8c6cb2f97fe0 wifi: mt76: mt7996: fix beacon command during disabling
8e4f72b682e9 wifi: mt76: mt7996: add implicit beamforming support for mt7992

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 3963dab0302ae29cbf2acf28f26c1432e4ddf1a5)

realtek: debounce reset key for Zyxel GS1900

When the reset button is next to the SFP cages, I2C operations on the
modules might cause interference on the button's GPIO line. Add a
debounce-interval of 5 times the poll-interval to ensure the line is
actually stable for some time and not just glitching.

This squashes commit 4357f32d41eb ("realtek: debounce reset key for
Zyxel GS1900") and commit 777c6106ed4e ("realtek: move debounce-interval
to correct node").

Signed-off-by: Sander Vanheule <sander@svanheule.net>

hostapd: backport upstream patch to fix setting BSS color

Without this patch, we get the following error:

Mon Dec 23 11:35:44 2024 daemon.err hostapd: nl80211: kernel reports: integer out of range

As updating hostapd would be too complex and requires further testing,
we backport this simple upstream fix instead.

Fixes: https://github.com/openwrt/openwrt/issues/16680
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/17590
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 5ce1af9539da667f62dc3cb426f9ec36e53fb54e)
Link: https://github.com/openwrt/openwrt/pull/17591
Signed-off-by: Robert Marko <robimarko@gmail.com>

ath79: teltonika-rut230: fix failsafe boot without SIM tray

Due to "SIM present" input defaulting to "button" type, it is
interpreted as such when booting, and causes the system to enter
failsafe, if the tray is missing. Similarly to rfkill switch on
TP-Link WDR4300 and Archer C7, make it EV_SW instead, to stop it from
interfering with the boot process.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17503
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 7b9ca01109827368deb68b7d8217643b78b87cb9)

ath79: teltonika-rut230: fix typo in "green:signal-strength4" LED

It's missing a hyphen present in every other LED from the set. Set it to
"green:signal-strength-4".

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17503
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit d04f41e092294789b5add6816bb3b3bd7570a30d)

apm821xx: fixes WNDAP620 + WNDAP660 sysupgrade failures

OpenWRT on the WNDAP6x0 refuses to sysupgrade to itself
due to a compat_version imbalance. The Image is generated
with version 2.0, but the uci-defaults says that it needs
to be at 3.0 for the device.

Fix this by downgrading WNDAP6x0 05_fix-compat-version's
values back to 2.0 so it matches what we use.

Fixes: 5815884c3a2a ("apm821xx: migrate to DSA")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit e9415be4ad3cacbbd6e65fee5213baf3eaf9e07a)

lantiq: xrx200_legacy: disable unused phy drivers

Subtarget xrx200_legacy supports only a few devices. They all use
the integrated Lantiq GSWIP switch and lantiq xway PHYs. The atheros
and icplus PHYs can be safely disabled.

Switches used by individual devices are listed below.

Device Switch PHY
Alpha ASL56026 Lantiq GSWIP int. switch
Arcadyan VG3503J Lantiq GSWIP int. switch
Netgear DM200 Lantiq GSWIP int. switch
TP-LINK TD-W8970 Lantiq GSWIP Lantiq PEF7071V
TP-Link TD-W8980 Lantiq GSWIP Lantiq PEF7071V

Reduces uncompressed kernel size by 16 kB.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/17581
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 517b9c1cdcd357fd84c7f27bd2886f235f3ec946)

lantiq: xway_legacy: refresh config

This was done by executing these command:
$ make kernel_oldconfig CONFIG_TARGET=subtarget

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/17581
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 524e22b4c71366be86493ca3ee7a16ff92d52288)

lantiq: xrx200: add alternative names for Plusnet Hub One and BT Business Hub 5A

The Plusnet Hub One and BT Business Hub 5A have the same hardware as
the BT Home Hub 5A. This commit adds alternative names so that both
devices can be easily found in the firmware selector.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/17583
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 1b045a7c13aeb141e0c069aaf5fc38989eee11cf)

lantiq: xrx200_legacy: add alternative names for TP-Link TD-W9980(B)

The TP-Link TD-W9980(B) shares the same hardware with the TP-Link TD-W8980.
The only difference is that the TD-W8980 does not support VDSL. This is a
software limitation and once the software is changed, both work equally
supporting VDSL. This commit adds alternative names for devices so they
can be easily found in the firmware selector.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/17583
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit b2b4ce15322c75bda0cae6fb2160a74270185831)

kernel: bump 6.6 to 6.6.71

Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.71

Manually rebased:
airoha/patches-6.6/110-01-clk-en7523-Rework-clock-handling-for-different-clock.patch
airoha/patches-6.6/111-mmc-mtk-sd-add-support-for-AN7581-MMC-Host.patch

All other patches automatically rebased.

Build system: x86/64
Build-tested: bcm27xx/bcm2712
Run-tested: bcm27xx/bcm2712

Signed-off-by: John Audia <therealgraysky@proton.me>
[ fix manually rebased patch ]
Link: https://github.com/openwrt/openwrt/pull/17568
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 3f87c5ac4221deb37d4c3e730e692eef8f9c9ffe)

kernel: bump 6.6 to 6.6.70

Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.70

Removed upstreamed:
generic/backport-6.6/902-net-llc-reset-skb-transport_header.patch[1]
generic/pending-6.6/605-netfilter-nft_set_hash-unaligned-atomic-read-on-stru.patch[2]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.70&id=0c896816aa193e6459fc947747e5753c06b395b9
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.70&id=4f49349c1963e507aa37c1ec05178faeb0103959

Build system: x86/64
Build-tested: bcm27xx/bcm2712, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Run-tested: bcm27xx/bcm2712, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/17545
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit efafd7d47f8fa26a9f99283605c9324a833ef852)

rockchip: disable kernel preemption

This setting is more suitable for device running OpenWRT.
Most OpenWRT targets are already default to this configuration,
and it has shown better performance in VPN (wireguard).

Fix: #17454

Signed-off-by: Kien Truong <duckientruong@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17575
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 1c178f364454c5b73eb453fa0b101ae2f6454d4c)

airoha: an7581: refresh DTS with changes for cpufreq, MTD and MMC

Refresh DTS with required changes for cpufreq, MTD and MMC. While at it
also fix wrong speed for MAC.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 17b0d1379a3cd4a2e2dbefa7d0f9bc281269f97e)

airoha: an7581: replace cpufreq patch with new version

Replace cpufreq patch with new version requested upstream.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 506955735075241d3467d632cae7ed5f10e21c2f)

airoha: an7581: add pending patch for ETS qdisc on ethernet driver

Add pending patch for ETS qdisc on Airoha ethernet driver.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 53bc7633317a7da9bf7ef440ed3da39404cf146e)

airoha: an7581: add pending patch to fix PCI

Add pending patch to fix PCIe missing register.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 77329b7d8d870897d85270a4e806ec0d04396685)

airoha: an7581: add patch fixing support for MMC

Add patch fixing support for MMC. Additional clock are needed for MMC to
work and some small fixup to make the Mediatek MMC driver on Airoha SoC.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit be5a9ff24b9c3b7d1b5bf508b84a35be9f9b3ea9)

kernel: modules: Add ETS Qdisc scheduler to sched KernelPackage

Add ETS Qdisch scheduler to kernel package modules.

Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
[ add commit description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 7e237f190225c0bcba0f5374632d0508f11398a8)

airoha: an7581: backport patch to support ETS and HTB sched

Backport patch to support ETS and HTB scheduler for airoha ethernet
driver.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 3ec3ea5316ceebae260f4d170c6e1c3a19864438)

airoha: an7581: backport 2 fix for airoha ethernet driver

Backport 2 fix for airoha ethernet driver merged upstream.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit b4ae5378d403aa263ba5ec26ccc333ab0de81cff)

airoha: an7581: replace BUS clock patch with upstream version

Replace BUS clock patch with upstream version with related tag
as it got approved and merged.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 07b49ce87660a0448c0535b481b330e1bd333a8c)

airoha: an7581: enable MMC and PCI and refresh config

Enable MMC and PCI config symbol and refresh config for Airoha AN7581.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 73d368868c9dd2facfdf3f58533ee6310b2a665c)

lantiq: Remove legacy LED migration script

This script was rendered obsolete after xrx200 target switched to DSA and
breaking config migration from old releases to 22.03.

Signed-off-by: Mustafa Can Elmacı <mustafacan@elmaci.net>
Link: https://github.com/openwrt/openwrt/pull/17383
Link: https://github.com/openwrt/openwrt/pull/17512
Signed-off-by: Robert Marko <robimarko@gmail.com>

lantiq: fritz7430: fix PCI ID

This platform has a bogus PCI ID for the chip. Correct it in DTS.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16555
Link: https://github.com/openwrt/openwrt/pull/17512
Signed-off-by: Robert Marko <robimarko@gmail.com>

lantiq: use nvmem for tplink tdw89x0

These two devices use different wifi chips and as a result, different
calibration sizes. Move the differences out of dtsi.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16555
Link: https://github.com/openwrt/openwrt/pull/17512
Signed-off-by: Robert Marko <robimarko@gmail.com>

lantiq: use nvmem for fritz 736x

Two use AR9287 and one AR9381. Both have different calibration sizes.
Move differences out of wifi node to make it clearer what's what.

qca,no-eeprom needs to stay for 7362sl as there's no nvmem equivalent
for caldata_extract_reverse

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17278
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/17512
Signed-off-by: Robert Marko <robimarko@gmail.com>

lantiq: use nvmem for fritz73x0

These units use AR9287, which has a calibration size of 3d8.

Also fixed compatible string to the proper one to indicate AR9287.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17278
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/17512
Signed-off-by: Robert Marko <robimarko@gmail.com>

lantiq: use regulator for USB GPIO

One is already present. The other one can be implemented in terms of the
PHY.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17250
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://github.com/openwrt/openwrt/pull/17512
Signed-off-by: Robert Marko <robimarko@gmail.com>

ipq40xx: fix label MAC address for Linksys WHW03 v2

The label MAC address is written inside the case of the whw03 v2 at the bottom.

Similar fix as to the 4040 in b22d382ae4eaa1af42930115d91855f402314cac

Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/17535
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit c113982706989c76c69e94e15abce0d316e97f6b)

ipq40xx: dts: add ethernet0 alias for all devices

Updating the driver patches for ipq40xx (correctly) removed the
ethernet0 alias from qcom-ipq4019.dtsi; however, on some devices this
alias is needed for the bootloader to set MAC addresses in the FDT.

As it is unknown which devices actually need the alias, simply add it to
all devices trees for now that enable the &gmac now to avoid regressions
from previous OpenWrt releases. The additional alias should not cause any
issues even when it is not needed.

A TODO comment is added to the same Device Trees to document that the
alias may not be needed (hopefully preventing it from being copied
unnecessarily to newly added devices in the future). The following
devices are known to need the alias for correct MAC address assignment,
so no TODO comment is added:

- FRITZ!Box 4040
- FRITZ!Box 7530

Fixes: cd9c7211241e ("ipq40xx: 6.1: use latest DSA and ethernet patches")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Link: https://github.com/openwrt/openwrt/pull/17442
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit d09dd75fbd1314ec5f3571511195da4012d7a51a)

generic: add gpio-regmap request/free ops patch

This patch is needed on bmips since it fixes issues with GPIOs not being
properly configured due to gpio_request_enable not being called on bcm63xx
devices. Therefore we can now drop the bcm63268 gpio function patch.

Backported from f5b1d340be9488af71e6522c3f10f1ebd1a35446 with the exception of
the realtek patch removal.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit f5b1d340be9488af71e6522c3f10f1ebd1a35446)

mac80211: set basic-rate for mesh interfaces

Basic rates were not set for mesh-interfaces, resulting in the undesired
behavior where 11s frames might be sent with a rate which was not
configured.

Depending on the driver, the basic rate might also be used to determine
the beacon rate configured to the chip. One such example are MediaTek
MT7915 platforms.

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 3ec7f3a512a27f8ca6402954ad2a997176103b4b)

ath79: reset ETH switch for AR9344

According to datasheet, on AR9344 the switch and switch analog need to
be reset first before initiating a full reset.

Resetting these systems fixes spurious reset hangs on Atheros AR9344
SoCs.

Link: https://github.com/freifunk-gluon/gluon/issues/2904
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 916af73fc388d638b1a717a2411792e0680dd8e6)

OpenWrt v24.10.0-rc5: revert to branch defaults

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

OpenWrt v24.10.0-rc5: adjust config defaults

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

mediatek/filogic: add support for Cudy AP3000 v1

Hardware:
  SoC:     MT7981b
  RAM:     512 MB
  Flash:   256 MB SPI NAND
  Ethernet:
    1x2.5Gbps (rtl8221b)
  WiFi:    2x2 MT7981
  Button:  Reset
  LED:     1x multicolor

Installation
------------
At the moment, firmware installation is only possible via a transition firmware.
It's can be requested from the manufacturer by email to support@cudy.com

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17225
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 6992d6e51af34603de099d7bbe9d7e848f109e22)

mediatek: Fix U-Boot variables handling for D-Link M30 A1

I think I implemented the U-Boot handling incorrectly on M30 (saw the issue while porting M60 to OpenWrt). Maybe someone with more U-Boot experience can have a look at it.
What I understood until now:

Before flashing, `sw_tryactive` must be set to 0 because OpenWrt runs on partition 0

During reset after flashing, U-Boot executes the following line:
`boot_rd_auto_sw_img=if itest.s ${sw_tryactive} == 2; then run boot_by_part; else run boot_by_tryactive; fi`

As `sw_tryactive` was set to 0 before flashing, `boot_by_tryactive` will be executed:
`boot_by_tryactive=if itest.s ${sw_tryactive} == 0; then setenv sw_tryactive 2; setenv sw_active 1; saveenv; run ub0; else setenv sw_tryactive 2; setenv sw_active 2; saveenv; run ub1; fi`

As `sw_tryactive` was set to 0 before flashing, `sw_active` will be set to 1 and `ub0` will be executed:
`ub0=setenv bootpart 0; mtkboardboot; run ub0to1; uip main; reset`

If the OpenWrt boot is successful, `ub0to1` and `uip` main will never be executed. Only in case OpenWrt cannot be loaded, `mtkboardboot` will return and the fallback `ub0to1` is executed.

Conclusion: It's sufficient to set `sw_tryacitve` to 0 before flashing, the added code in `target/linux/mediatek/filogic/base-files/etc/init.d/bootcount` is useless.
In the worst case (/proc/cmdline doesn't contain `bootpart=ubi0` as expected), the bootpart variable would be set to 1 and causes starting the firmware from the second partition instead of the one on the first partition.

Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17298
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 70610a5240a94648e178713f091435bd0ba158d3)

mac80211: rt2x00: some improvements for rt5592

This patch contains some performance and stability improvements
for RT5592:

1. Fix RFCSR register init values for RT5592.
2. Fix BBP register init values for RT5592.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16845
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 59557ca19a460d8ad70991f63616d1ad0dfe9823)

mac80211: rt2x00: some improvements for mt7620

This patch contains some performance and stability improvements
for MT7620:

1. Always calibrate MT7620 when switching channel.
2. Rework link tuner for MT7620.
3. Correct MT7620 SDM mode register value.
4. Fix register operation on RXIQ calibration.
5. Fix TX_PIN_CFG and TX_ALC_VGA3 init values.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16845
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 5d583901657bdfbbf9fad77d9247872427aa5c99)

mac80211: rt2x00: some improvements for rt2800 generic

1. Respect the rt2800 hardware TX queue index.
2. Increase the watchdog sampling frequency.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16845
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 70733c6093ee1e2fae12fdff97425270ea733dae)

realtek: trim default package selection

Images for certain devices are staring to become too large, as some
device only have 6MB available in their vendor partition layout for the
initial install. This is especially pressing for bootloaders only
supporting gzip compression.

Drop some packages from DEFAULT_PACKAGES that aren't strictly required
for a factory install. The user can always install more packages later
using opkg/apk, or via a sysupgrade to a custom build.

firewall4 is kept to ensure the most recent firewall package is selected
in builds including LuCI.
ethtool is kept as a frequently used diagnostics tool.

Link: https://github.com/openwrt/openwrt/pull/17450
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit c9ae39b2d156ff893d88a7d75b9044aac2fdd8d0)

ath79: Push MV88E6060 DSA switch into package

We can use a package for the MV88E6060 DSA switch on the single
ath79 device that uses it, saving around 600 KB of memory on
all other devices (for the DSA infrastructure, mainly).

As far as I can see the TP-Link TL WR941 v2 is the only device
using MV88E6060 and the only device with a DSA switch overall.

However the ath79 people should look at this so I'm not
mistaken.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250102-ath79-mv88e6060-module-v1-1-c2a8e31e72fc@linaro.org/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit e7419381fdd43a49e7583a786ce2d9c2ed1b4afe)

ixp4xx: Break out mv88e6060 DSA switch to package

Just one of the devices uses the Marvell MV88E6060 DSA
switch so break this out from the generic kernel config
and into a package selected only by that single device
and probed at boot instead.

The big win is from being able to drop the dsa_core
(~600KB) kernel module out of the common kernel on
devices with no DSA switch.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
(cherry picked from commit 2456a2fd7f72d6afcee4ac9c2eccb312d0b1d36d)

mediatek: append metadata to factory-uboot.bin for WSR devices

Append metadata to factory-uboot.bin image to pass the image verification
on sysupgrade.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17408
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit a06a2ef89db03fac2cbd950304e5b507da9deb1e)

lantiq: xrx200: add support for lan3 and lan4 on AVM 5490/5491

On the AVM 5490/5491, lan1, lan2 and wan ports are connected directly
to the internal GSWIP switch. The lan3 and lan4 ports are connected via
an external QCA8334 switch. This commit adds the missing entries in dts
and adds the driver module.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/17473
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 14be320291e0c00a1291ad8bd220fd37b12ba138)

base-files: strip space and tab characters from ASCII mac address

Spaces and tabs are widely used in variable definitions. We have to
remove them to ensure that get_mac_ascii() works properly.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17262
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 551e04f3c9c063d885ca7a91db36f27f684a3a5c)

base-files: enable get_mac_ascii() to handle redundant strings

The function get_mac_ascii() will fail when there are two or more
same MAC address variable names in the mtd partition. Only retain
the first variable to workaround this rare situation.

Fixes: https://github.com/openwrt/openwrt/issues/17236
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17262
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 3410ad2f40c085e5db7a71f6ae4b80734826a1e3)

uboot-mediatek: add missing LED command for OpenWrt One

The u-boot LED command "led_loop_done" is missing from the OpenWrt
One NAND flash u-boot. Copy it from the OpenWrt One NOR flash u-boot
default environment to fix this issue.

Fixes: https://github.com/openwrt/openwrt/issues/17310
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17338
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 5ef71eaafd4e128ec3708a66b5633214427da373)

uboot-mediatek: fix Routerich AX3000 support patch

It seems that the original patch has been manually modified. The
newly added line number is incorrect.

Fixes: c0581520b1c5 ("uboot-mediatek: add Routerich AX3000 support")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17338
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 9f97e39a9336e279be7ea1c00c4221ec3f448457)

ramips: mtk-mmc: remove nt76x8 pinctrl hack

Now we can set the mt76x8 SDXC pinmux in device tree.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17446
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit b4a9f85c1394f13806fc2f51f5f6f23494773d7e)

ramips: make package kmod-sdhci-mt7620 conflict with kmod-mmc-mtk

These two packages are SDXC drivers for Mediatek mt762x series SoCs.
One is upstream implementation, and the other is downstream driver.
Installing them together will result in conflicts.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17446
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 0764e3008228bbdafb5e4a9837fe9efec7e138a0)

ramips: fix SDXC function for mt76x8 one eth port devices

There are only 5 devices in mt76x8 sub-target selected the MTK SDXC
driver package. And they are all single ethernet port routers or dev
boards:

* LinkIt Smart 7688
* Onion Omega2+
* RAVPower RP-WD009
* VoCore VoCore2
* VoCore VoCore2-Lite

For these devices, they are using the ephy p1 - p4 as the SDXC IO
pins. Therefore, these GPIO pads must be configured in "digital"
IO mode.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17446
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit f5996ae947c88461029060d74ace6a85a30dd9fd)

ramips: add back SDXC card reader support for HiWiFi HC5x61A

After adding the correct package and pin group configurations,
the SDXC card slot can now function properly.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17446
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit cea4aae0a921d71407d11957502f8cc3b652be21)

ramips: mmc-mtk: add more vendor driver register init values

In the MTK vendor driver, mt762x SDXC registers MSDC_PATCH_BIT and
MSDC_PATCH_BIT1 have different init values than upstream driver.
These magical values should have some help for the stability.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17446
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit f70cdfd682a87c9de942f9251fb5a0caaf43f7cf)

ramips: mt762{0,8}: reduce default MMC clock to 24 MHz

The upstream mtk-sd driver did not perform specific timing
optimization for MT762x series SoC, hence the SDHC peripheral
of some boards cannot run at too high frequency. Reduce the
maximum clock frequency to fix the mmc read/write error.

Closes: https://github.com/openwrt/openwrt/issues/17364
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17375
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit de0c143742517d401c4730137f092be8fb7e882a)

bcm27xx: remove duplicated kmod-rp1-pio package

Commit f105d1a9a9739267fb25612d039c392a397775bd added a duplicated
kmod-rp1-pio package.
Also remove unneeded blank lines added by the same commit.

Fixes: f105d1a9a973 ("bcm27xx/bcm2712: Fix-up RP1 modules")
Signed-off-by: John Audia <therealgraysky@proton.me>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit d5669c040beb0fa29e6916049941f0e76ce07460)

rockchip: enable USB3 port on NanoPC T6

Enable the USB3 port on FriendlyELEC NanoPC-T6.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/17349
(cherry picked from commit 6881b48dc603e25320a14e11c5e1797321891b76)
Link: https://github.com/openwrt/openwrt/pull/17466
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

rockchip: backport recent rk3588 clk updates

Backport recent rk3588 clk updates from upstream,
including one bug fix.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/17349
(cherry picked from commit 8ad02ca2f8477b1cfdc5ea6124fae60c07687aa1)
Link: https://github.com/openwrt/openwrt/pull/17466
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>