Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-next into for-davem

net, sch: fix the typo in register_qdisc()

Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net, rps: fix the comment of net_rps_action_and_irq_enable()

Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net, rps: fix build failure when CONFIG_RPS isn't set

In file included from net/socket.c:99:0:
include/net/sock.h: In function ‘sock_rps_record_flow’:
include/net/sock.h:849:30: error: ‘const struct sock’ has no member named ‘sk_rxhash’
include/net/sock.h: In function ‘sock_rps_reset_flow’:
include/net/sock.h:854:29: error: ‘const struct sock’ has no member named ‘sk_rxhash’

Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: move skb_dst_set() a bit downwards in sctp_packet_transmit()

skb_dst_set will use dst, if dst is NULL although is not a problem,
then goto the 'no_route' and free nskb, so do the skb_dst_set is pointless.
so move the skb_dst_set after dst check.
Remove the unnecessary initialization as well.

v2: fix the subject line because it would confuse people,
    as pointed out by Daniel.

Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sch_netem: support of 64bit rates

Add a new attribute to support 64bit rates so that
tc can use them to break the 32bit limit.

Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

sch_netem: more precise length of packets

With TSO/GSO/GRO packets, skb->len doesn't represent
a precise amount of bytes on wire.
This patch replace skb->len with qdisc_pkt_len(skb)
which is more precise.

Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/mlx4_en: Add netdev support for TCP/IP offloads of vxlan tunneling

When the device tunneling offloads mode is vxlan do the following

 - call SET_PORT with the relevant setting

 - add DMFS steering vxlan rule for the device self and multicast mac addresses
   of the form: {<ETH, outer-mac> <VXLAN, ANY vnid> <ETH, ANY mac>} --> RSS QP

 - set relevant QPC fields in RSS context and RX ring QPs

 - in TX flow, set WQE fields to generate HW checksum, and handle gso skbs
   which are marked for encapsulation such that the HW will segment them properly.

 - in RX flow, read HW offloaded checksum for encapsulated packets from the CQE

 - advertize hw_enc_features and NETIF_F_GSO_UDP_TUNNEL to the networking stack

Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/mlx4_core: Add basic support for TCP/IP offloads under tunneling

Add the low-level device commands and definitions used for TCP/IP HW offloads
of tunneled/vxlan traffic which are supported by the ConnectX3-pro NIC.

This is done through the following elements:

 - read tunneling device caps in QUERY_DEV_CAP
 - add helper function to do SET_PORT for tunneling
 - add DMFS VXLAN steering rule definitions
 - add CQE and WQE checksum offload field definitions

Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netlink: specify netlink packet direction for nlmon

In order to facilitate development for netlink protocol dissector,
fill the unused field skb->pkt_type of the cloned skb with a hint
of the address space of the new owner (receiver) socket in the
notion of "to kernel" resp. "to user".

At the time we invoke __netlink_deliver_tap_skb(), we already have
set the new skb owner via netlink_skb_set_owner_r(), so we can use
that for netlink_is_kernel() probing.

In normal PF_PACKET network traffic, this field denotes if the
packet is destined for us (PACKET_HOST), if it's broadcast
(PACKET_BROADCAST), etc.

As we only have 3 bit reserved, we can use the value (= 6) of
PACKET_FASTROUTE as it's _not used_ anywhere in the whole kernel
and not supported anywhere, and packets of such type were never
exposed to user space, so there are no overlapping users of such
kind. Thus, as wished, that seems the only way to make both
PACKET_* values non-overlapping and therefore device agnostic.

By using those two flags for netlink skbs on nlmon devices, they
can be made available and picked up via sll_pkttype (previously
unused in netlink context) in struct sockaddr_ll. We now have
these two directions:

 - PACKET_USER (= 6)    ->  to user space
 - PACKET_KERNEL (= 7)  ->  to kernel space

Partial `ip a` example strace for sa_family=AF_NETLINK with
detected nl msg direction:

syscall:                     direction:
sendto(3,  ...) = 40         /* to kernel */
recvmsg(3, ...) = 3404       /* to user */
recvmsg(3, ...) = 1120       /* to user */
recvmsg(3, ...) = 20         /* to user */
sendto(3,  ...) = 40         /* to kernel */
recvmsg(3, ...) = 168        /* to user */
recvmsg(3, ...) = 144        /* to user */
recvmsg(3, ...) = 20         /* to user */

Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Jakub Zawadzki <darkjames-ws@darkjames.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

netlink: only do not deliver to tap when both sides are kernel sks

We should also deliver packets to nlmon devices when we are in
netlink_unicast_kernel(), and only one of the {src,dst} sockets
is user sk and the other one kernel sk. That's e.g. the case in
netlink diag, netlink route, etc. Still, forbid to deliver messages
from kernel to kernel sks.

Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Jakub Zawadzki <darkjames-ws@darkjames.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'sctp_logspam'

Neil Horman says:

====================
sctp: Consolidate and ratelimit deprecation warnings

The SCTP protocol has several deprecation warnings in its setsockopt path that
can be triggered by unprivlidged users.  Since these are not ratelimited, we can
spam the logs quite easily here.  Since these are all deprecation warnings, and
that type of warning isn't uncommon in the rest of the kernel, lets make a
common pr_warn_deprecated macro to produce somewhat generalized ratelimited
deprecation warnings easily
====================

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

SCTP: Reduce log spamming for sctp setsockopt

During a recent discussion regarding some sctp socket options, it was noted that
we have several points at which we issue log warnings that can be flooded at an
unbounded rate by any user.  Fix this by converting all the pr_warns in the
sctp_setsockopt path to be pr_warn_ratelimited.

Note there are several debug level messages as well.  I'm leaving those alone,
as, if you turn on pr_debug, you likely want lots of verbosity.

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Vlad Yasevich <vyasevich@gmail.com>
CC: David Miller <davem@davemloft.net>
CC: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

printk: Add a DEPRECATED macro

sctp has several points in its setsockopt path in which it issues deprecation
warnings.  It seems like it might be handy to macrotize such a warning so other
subsystems can use it easily

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC: "David S. Miller" <davem@davemloft.net>
CC: linux-kernel@vger.kernel.org
CC: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

sch_dsmark: use correct func name in print messages

In dsmark_drop(), the function name printed by pr_debug
is "dsmark_reset", correct it to "dsmark_drop" by using
__func__ .

BTW, replace the other function names with __func__ .

Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sch_htb: use /* comments

Do not use C99 // comments and correct a spelling typo.

Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net_sched: replace pr_warning with pr_warn

Prefer pr_warn(... to pr_warning(...

Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

packet: fix "foo * bar" and "(foo*)" problems

Cleanup checkpatch errors.Specially,the second changed line
is exactly 80 columns long.

Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: unneccessary to get address prefix in addrconf_get_prefix_route

Since addrconf_get_prefix_route inputs the address prefix to fib6_locate,
which does not uses the data which is out of the prefix_len length,
so do not need to use ipv6_addr_prefix to get address prefix.

Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'tun_rfs'

Zhi Yong Wu says:

====================
tun: add the RFS support

Since Tom Herbert's hash related patchset was modified and got merged,
his pachset about adding support for RFS on tun flows also need to get
adjusted accordingly. I tried to update them, and before i will start
to do some perf tests, i hope to get one correct code base, so it's time
to post them out now. Any constructive comments are welcome, thanks.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

tun: Add support for RFS on tun flows

This patch adds support so that the rps_flow_tables (RFS) can be
programmed using the tun flows which are already set up to track flows
for the purposes of queue selection.

On the receive path (corresponding to select_queue and tun_net_xmit) the
rxhash is saved in the flow_entry.  The original code only does flow
lookup in select_queue, so this patch adds a flow lookup in tun_net_xmit
if num_queues == 1 (select_queue is not called from
dev_queue_xmit->netdev_pick_tx in that case).

The flow is recorded (processing CPU) in tun_flow_update (TX path), and
reset when flow is deleted.

Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Allow setting sock flow hash without a sock

This patch adds sock_rps_record_flow_hash and sock_rps_reset_flow_hash
which take a hash value as an argument and sets the sock_flow_table
accordingly.  This allows the table to be populated in cases where flow
is being tracked outside of a sock structure.

sock_rps_record_flow and sock_rps_reset_flow call this function
where the hash is taken from sk_rxhash.

Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bonding: update Documentation/networking/bonding.txt for option lp_interval

Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bonding: ust micro BOND_NO_USE_ARP to simplify the mode check

The bond 3ad and TLB/ALB has the same check path, so combine them.

Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bonding: add option lp_interval for loading module

The bond driver could set the lp_interval when loading module.

Suggested-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

lro: remove dead code

Remove leftover code that is not used anywhere in current tree.

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

bonding: make local function static

bond_xmit_slave_id is only used in main.

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: make local functions static

The following are only used in one file:
  tcp_connect_init
  tcp_set_rto

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/7990: Make lance_private.name const

This allows to drop a few casts.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/7990: Fix whitespace errors

Most of them reported by checkpatch.pl

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv4: ping make local stuff static

Don't export ping_table or ping_v4_sendmsg. Both are only used
inside ping code.

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv4: remove unused function

inetpeer_invalidate_family defined but never used

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

arp: make arp_invalidate static

Don't export arp_invalidate, only used in arp.c

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv4: make fib_detect_death static

Make fib_detect_death function static only used in one file.

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

macvlan: make start_xmit local

Only used in one file, no need to expose

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

bgmac: use phy_mii_ioctl in ioctl handler

This works pretty much the same way, so avoid duplicating the code.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bgmac: drop duplicated PHY defines

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ieee802154: space prohibited before that close parenthesis

Fix checkpatch error with space.

Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

llc: "foo* bar" should be "foo *bar"

Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tile_net: Always enable PTP clock support on TILE-Gx

All other net drivers with PTP support enable it unconditionally.
Make tile_net consistent with this.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: Fix build with SRIOV disabled.

drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c: In function 'bnx2x_drv_info_ether_stat':
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c:3302:46: error: dereferencing pointer to incomplete type
make[6]: *** [drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.o] Error 1

Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vmxnet3: use initialized skb pointer to set hash

The recent conversion to skb_set_hash() was incorrect. 'skb' is
uninitialized at this point.

Fixes: 0b6807034791 ('net: vmxnet3 calls skb_set_hash')
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sch_tbf: add TBF_BURST/TBF_PBURST attribute

When we set burst to 1514 with low rate in userspace,
the kernel get a value of burst that less than 1514,
which doesn't work.

Because it may make some loss when transform burst
to buffer in userspace. This makes burst lose some
bytes, when the kernel transform the buffer back to
burst.

This patch adds two new attributes to support sending
burst/mtu to kernel directly to avoid the loss.

Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: fix checkpatch errors with //commen

Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: fix checkpatch errors with open brace '{' and trailing statements

fix checkpatch errors below:
ERROR: that open brace { should be on the previous line
ERROR: open brace '{' following function declarations go on the next line
ERROR: trailing statements should be on next line

Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: fix checkpatch errors with indent

fix checkpatch errors below:
ERROR: switch and case should be at the same inden
ERROR: code indent should use tabs where possible

Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: fix checkpatch errors with (foo*)|foo * bar|foo* bar

fix checkpatch errors below:
ERROR: "(foo*)" should be "(foo *)"
ERROR: "foo * bar" should be "foo *bar"
ERROR: "foo* bar" should be "foo *bar"

Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: fix checkpatch errors with space required or prohibited

fix checkpatch errors while the space is required or prohibited
to the "=,()++..."

Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: cleanup for tcp_ipv6.c

Fix some checkpatch errors for tcp_ipv6.c

Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv4: ipv4: Cleanup the comments in tcp_yeah.c

This cleanup the comments in tcp_yeah.c.
1.The old link is dead,use a new one to instead.
2.'lin' add nothing useful,remove it.
3.do not use C99 // comments.

Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv4: ERROR: code indent should use tabs where possible

Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv4: ERROR: do not initialise globals to 0 or NULL

Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv4: fix all space errors in file igmp.c

Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv4: fix checkpatch error with foo * bar

Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv4: fix checkpatch error "space prohibited"

Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv4: do clean up with spaces

Fix checkpatch errors like:
ERROR: spaces required around that XXX

Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'bnx2x'

Yuval Mintz says:

====================
bnx2x: new features patch series

This patch series adds/fixes several new features in the bnx2x driver -
it adds support for loading the bnx2x over an UNDI running on a Multi-function
device, adds missing bits for PCIe AER support and enables VFs to properly
configure multicast filters
(In addition, it also contains some small improvements in driver behaviour).

Please consider applying these patches to `net-next'.

Changes from previous versions
------------------------------
  v2:
     - Fixed comment typo in patch 4 (propogate --> propagate)
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: add VF Multicast filters support

This patch adds the necessary support for configuring (and removing) multicast
filters to VFs.

Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: Add num of VFs to Management statistics

Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: no error when RSS configuration fails

It's possible for VMs with older versions of bnx2x to run over a hypervisor
with latest driver. If a VF in such a VM does not support RSS configuration,
the PF driver in the hypervisor will print an error message to system logs.

This changes the error message into a debug message, as this is very likely
a false alarm for an older VF (i.e., VF manages to work properly; PF simply
cannot configure the additional queues for it).

Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: add Big-Endian ethtool comment

There's a known issue that using `ethtool -e' flips the endianity of the
written data, i.e., using `ethtool -E' to dump eeprom image and than using
`ethtool -e' to re-write that same image will result in an image where
the data has the opposite endianity.
Sadly, this cannot be fixed as there are already various tools deployed
based on the endianity of the eeprom read/write.
Instead, a comment is added to the code to help explain why this is un-fixable.

Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: Add AER support (missing bits)

This function adds several OS calls required to fully enable PCIe AER support -
pci_enable_pcie_error_reporting() and pci_cleanup_aer_uncorrect_error_status().

Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: Add support for Multi-Function UNDI

This adds the ability for bnx2x to load after UNDI is used in the
preboot environment on a multi-function interface which is not the first
interface of a given device.
Notice a side-effect is that the order by which the functions are probed and
thus interfaces appear might change, as this patch utilizes the EPROBE_DEFER
return value (and mechanism).

Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'addr_compare'

Ding Tianhong says:

====================
slight optimization of addr compare for some modules

Joe Perches add ether_addr_equal_unaligned to test if
possibly unaligned to u16 Ethernet addresses are equal.

If CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is set, this uses
the slightly faster generic routine ether_addr_equal,
otherwise this uses memcmp.

So I use the recently added and possibly more efficient
ether_addr_equal_unaligned to instead of memcmp for slight
optimization.

v2: Because a lot of places are already using 16b aligned MAC
    address for both operands, so use the ether_addr_equal to
    instead of ether_addr_equal_unaligned.Thanks for Joe, Alex
    and Antonio's opinions.
    Also remove the patch for bridge.

v3: According Joe's suggestion, the patch
    (net: slight optimization of addr compare for some modules)
    should be broken into several patches, and it will be good
    to review for maintainers. So I will send rest of the patches
    for first step, and next step, I will seperate the netdev patch
    and send them by another patchset for net-next.
    also fix some changelog.

v3.5 Change some style for patch 8 and patch 13. Thanks for
     Sergei's suggestion.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

wireless: slight optimization of addr compare

Use possibly more efficient ether_addr_equal or
ether_addr_equal_unaligned instead of memcmp.

Cc: John W. Linville <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rtlwifi: slight optimization of addr compare

Use possibly more efficient ether_addr_equal_unaligned
instead of memcmp.

Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mwifiex: slight optimization of addr compare

Use possibly more efficient ether_addr_equal
instead of memcmp.

Cc: Bing Zhao <bzhao@marvell.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipw2x00: slight optimization of addr compare

Use possibly more efficient ether_addr_equal
instead of memcmp.

Cc: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cw1200: slight optimization of addr compare

Use possibly more efficient ether_addr_equal
instead of memcmp.

Cc: Solomon Peachy <pizza@shaftnet.org>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

hostap: slight optimization of addr compare

Use possibly more efficient ether_addr_equal
instead of memcmp.

Cc: Jouni Malinen <j@w1.fi>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

media: dvb_core: slight optimization of addr compare

Use possibly more efficient ether_addr_equal
instead of memcmp.

Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: linux-media@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

isdn: slight optimization of addr compare

Use possibly more efficient ether_addr_equal
instead of memcmp.

Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

atm: slight optimization of addr compare

Use possibly more efficient ether_addr_equal
instead of memcmp.

Cc: Chas Williams <chas@cmf.nrl.navy.mil>
Cc: linux-atm-general@lists.sourceforge.net
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mac8011: slight optimization of addr compare

Use the possibly more efficient ether_addr_equal
to instead of memcmp.

Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: David Miller <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

infiniband: slight optimization of addr compare

Use the possibly more efficient ether_addr_equal
to instead of memcmp.

Cc: Roland Dreier <roland@kernel.org>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: Faisal Latif <faisal.latif@intel.com>
Cc: linux-rdma@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ozwpan: slight optimization of addr compare

Use possibly more efficient ether_addr_equal
instead of memcmp.

Cc: Rupesh Gujare <rupesh.gujare@atmel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: devel@driverdev.osuosl.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Tan Xiaojun <tanxiaojun@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

zd1211rw: slight optimization of addr compare

Use possibly more efficient ether_addr_equal
instead of memcmp.

Cc: Daniel Drake <dsd@gentoo.org>
Cc: Ulrich Kunitz <kune@deine-taler.de>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Tan Xiaojun <tanxiaojun@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

batman-adv: use batadv_compare_eth for concise

It is better to use batadv_compate_eth instead of memcpy for
concise style.

Cc: Marek Lindner <mareklindner@neomailbox.ch>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Cc: Antonio Quartulli <antonio@meshcoding.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: b.a.t.m.a.n@lists.open-mesh.org
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Tan Xiaojun <tanxiaojun@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ppp: slight optimization of addr compare

Use possibly more efficient ether_addr_equal
to instead of memcmp.

Cc: Michal Ostrowski <mostrows@earthlink.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

hamradio: slight optimization of addr compare

Use possibly more efficient ether_addr_equal
to instead of memcmp.

Cc: Joerg Reuter <jreuter@yaina.de>
Cc: linux-hams@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: atl1: slight optimization of addr compare

Use the recently added and possibly more efficient
ether_addr_equal_unaligned to instead of memcmp.

Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Chris Snook <chris.snook@gmail.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: pcnet: slight optimization of addr compare

Use possibly more efficient ether_addr_equal
to instead of memcmp.

Cc: Don Fry <pcnet32@frontier.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: freescale: remove unused compare_addr()

The function did not be used any more, so remove it.

Cc: Li Yang <leoli@freescale.com>
Cc: netdev@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlge: make local function static

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

mdio: unused ethtool functions

Use it or lose it.

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

hhf: make qdisc ops static

This module shouldn't be randomly exporting symbols

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

rose: cleanup checkpatch errors,spaces required

This patch add spaces to cleanup checkpatch errors.

Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: remove the never used 'return' and redundant 'break'

In switch() had do return, and never use the 'return NULL'. The
'break' after return or goto has no effect. Remove it.

v2: make it more readable as suggested by Neil.

Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mac802154: fix following checkpath.pl warning Prefer pr_warn(... to pr_warning(...

This patch fixes checkpath.pl:
 WARNING: Prefer pr_warn(... to pr_warning(...
 #447: FILE: ./wpan.c:447:

Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cxgb4: make functions static and remove dead code

Cleanup by making local functions static.

The code to load config file is unreachable in net-next, probably came
from some out of tree driver.

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: remove casting from function calls through ops structure

remove the unnecessary cast.

Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netconf: add support for IPv6 proxy_ndp

Need to be able to see changes to proxy NDP status on a per
interface basis via netlink (analog to proxy_arp).

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netconf: rename PROXY_ARP to NEIGH_PROXY

Use same field for both IPv4 (proxy_arp) and IPv6 (proxy_ndp)
so fix it before API is set to be a common name

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: vxlan: use custom ndo_change_mtu handler

When adding a new vxlan device to an "underlying carrier" (here:
dst->remote_ifindex), the MTU size assigned to the vxlan device
is the MTU at setup time of the carrier - needed headroom, when
adding a vxlan device w/o explicit carrier, then it defaults
to 1500.

In case of an explicit carrier that supports jumbo frames, we
currently cannot change vxlan MTU via ip(8) to > 1500 in
post-setup time, as vxlan driver uses eth_change_mtu() as default
method for manually setting MTU.

Hence, use a custom implementation that only falls back to
eth_change_mtu() in case we didn't use a dev parameter on device
setup time, and otherwise allow a max MTU setting of the carrier
incl. adjustment for headroom.

Reported-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: use kfree_skb_list() helper

We can use kfree_skb_list() instead of open coding it.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'for-davem' of git://gitorious.org/linux-can/linux-can-next

Marc Kleine-Budde says:

====================
this is a pull request of three patches for net-next/master.

There is a patch by Oliver Hartkopp, to clean up the CAN gw code.
Alexander Shiyan adds device tree support to the mcp251x driver and a
patch by Ezequiel Garcia lets the ti_hecc driver compile on all ARM
platforms.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: move ip6_sk_accept_pmtu from generic pmtu update path to ipv6 one

In commit 93b36cf3425b9b ("ipv6: support IPV6_PMTU_INTERFACE on sockets")
I made a horrible mistake to add ip6_sk_accept_pmtu to the generic
sctp_icmp_frag_needed path. This results in build warnings if IPv6 is
disabled which were luckily caught by Fengguang's kbuild bot. But it
also leads to a kernel panic IPv4 frag-needed packet is received.

Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Revert "sctp: fix missing include file"

This reverts commit ac0917f250c61ae1e395844ebd924db0e07d1f87.

Better version of this fix forthcoming.

Signed-off-by: David S. Miller <davem@davemloft.net>

can: ti_hecc: Replace platform dependency with ARM dependency

OMAP's ti_hecc driver is used to support the CAN controller on many omap2plus
SoCs (OMAP2430, OMAP3, OMAP4, OMAP5 and AM335x), so it's wrong to make this
depend on OMAP3 only. Take an extra step, to get wider build coverage, and make
the driver depend on ARM.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

can: mcp251x: Add device tree support

This patch adds Device Tree support to the Microchip MCP251X driver.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>