Dhananjay Phadke [Fri, 13 Feb 2009 00:41:14 +0000 (16:41 -0800)]
netxen: remove pcie workaround
Remove workaround for pcie bug in early revisions of NX3031
(rev 41 or earlier). This is taken care of during firmware init.
The workaround required writing pcie config reg of every
pcie function on a card, not all of which are enabled.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roel Kluin [Fri, 13 Feb 2009 00:40:20 +0000 (16:40 -0800)]
sun3: print when lance_open() fails
With while (--i > 0) { ... } i reaches 0; print when lance_open() fails
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ron Mercer [Fri, 13 Feb 2009 00:38:34 +0000 (16:38 -0800)]
qlge: bugfix: Add missing rx buf clean index on early exit.
The large receive buffer queue is not properly tracking the current
index in the case where an early exit occurs. This can happen when a
page alloc or dma mapping fails. If this occurs the queue will get
out of sync and invalid indexes can be written to the hardware.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ron Mercer [Fri, 13 Feb 2009 00:38:18 +0000 (16:38 -0800)]
qlge: bugfix: Fix RX scaling values.
Receive packets were only scaling across 2 of the receive queues. The
value was hardcoded to 2 instead of being based on how many rx queues
were running.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ron Mercer [Fri, 13 Feb 2009 00:38:03 +0000 (16:38 -0800)]
qlge: bugfix: Fix TSO breakage.
Moved the buffer mapping to a point after TSO logic has modified the
iph->check field. We were seeing stale data on the PCIe bus.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ron Mercer [Fri, 13 Feb 2009 00:37:48 +0000 (16:37 -0800)]
qlge: bugfix: Add missing dev_kfree_skb_any() call.
We put the skb back if we can't get mapping for it. We don't
want unmapped buffers on our receive buffer queue.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ron Mercer [Fri, 13 Feb 2009 00:37:32 +0000 (16:37 -0800)]
qlge: bugfix: Add missing put_page() call.
We put the page back if we can't get mapping for it. We don't
want unmapped buffers on our receive buffer queue.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ron Mercer [Fri, 13 Feb 2009 00:37:13 +0000 (16:37 -0800)]
qlge: bugfix: Fix fatal error recovery hang.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ron Mercer [Fri, 13 Feb 2009 00:36:50 +0000 (16:36 -0800)]
qlge: bugfix: Use netif_receive_skb() and vlan_hwaccel_receive_skb().
Replace calls to vlan_hwaccel_rx() and netif_rx().
Thanks to Dave Miller for pointing out the the driver was making
the wrong upcall for passing packets into the stack.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roel Kluin [Fri, 13 Feb 2009 00:33:27 +0000 (16:33 -0800)]
TG3: limit reaches -1
With while (limit--) { ... } limit reaches -1, so 0 means success.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reinette Chatre [Tue, 10 Feb 2009 20:02:49 +0000 (12:02 -0800)]
iwlwifi: fix suspend/resume and its usage of pci saved state
Here we do two things:
First, revert "iwlwifi: save PCI state before suspend, restore after
resume". That misguided patch led to being unable to use iwlwifi
devices after resume.
Next, indicate to PCI driver that the saved PCI state is valid during suspend.
We restore PCI state and enable the device when network interface is created,
similarly PCI state is saved and the device is disabled when network interface
is removed. Thus, when .suspend is called the PCI state is saved and device
is disabled. This is the case even if an interface is never created as PCI
state is saved and device disabled during .probe.
PCI driver assumes PCI state is saved in .suspend. Saving the state at this
time will save state of disabled device and thus cause problems during
resume (resuming a disabled device). We thus indicate directly to PCI
driver that current PCI saved state is valid.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Alex Riesen <fork0@users.sf.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hin-Tak Leung [Wed, 4 Feb 2009 23:40:43 +0000 (23:40 +0000)]
zd1211rw: treat MAXIM_NEW_RF(0x08) as UW2453_RF(0x09) for TP-Link WN322/422G
Three people (Petr Mensik <pihhan@cipis.net>
["si" should be U+0161 U+00ED], Stephen Ho <stephenhoinhk@gmail.com>
on zd1211-devs and Ismael Ojeda Perez <iojedaperez@gmail.com>
on linux-wireless) reported success in getting TP-Link WN322G/WN422G
working by treating MAXIM_NEW_RF(0x08) as UW2453_RF(0x09) for rf
chip hardware initialization.
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Tested-by: Petr Mensik <pihhan@cipis.net>
Tested-by: Stephen Ho <stephenhoinhk@gmail.com>
Tested-by: Ismael Ojeda Perez <iojedaperez@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hin-Tak Leung [Sun, 8 Feb 2009 02:13:56 +0000 (02:13 +0000)]
zd1211rw: adding 0ace:0xa211 as a ZD1211 device
Christoph Biedl <sourceforge.bnwi@manchmal.in-ulm.de> reported success
in the sourceforge zd1211 mailing list on this addition. This product ID
was supported by the vendor driver ZD1211LnxDrv 2.22.0.0 (and possibly
earlier) and it probably should have been added earlier.
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Tested-by: Christoph Biedl <sourceforge.bnwi@manchmal.in-ulm.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 5 Feb 2009 23:27:32 +0000 (00:27 +0100)]
mac80211: restrict to AP in outgoing interface heuristic
We try to find the correct outgoing interface for injected frames
based on the TA, but since this is a hack for hostapd 11w, restrict
the heuristic to AP mode interfaces. At some point we'll add the
ability to give an interface index in radiotap or so and just
remove this heuristic again.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org [2.6.28.x]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bob Copeland [Sat, 10 Jan 2009 19:42:54 +0000 (14:42 -0500)]
ath5k: fix bf->skb==NULL panic in ath5k_tasklet_rx
Under memory pressure, we may not be able to allocate a new skb for
new packets. If the allocation fails, ath5k_tasklet_rx will exit but
will leave a buffer in the list with a NULL skb, eventually triggering
a BUG_ON.
Extract the skb allocation from ath5k_rxbuf_setup() and change the
tasklet to allocate the next skb before accepting a packet.
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Meelis Roos [Wed, 11 Feb 2009 01:29:42 +0000 (17:29 -0800)]
sunhme: Fix Quattro HME irq registration on proble failures
Currently, the sunhme driver installs SBus Quattro interrupt handler
when at least one HME card was initialized correctly and at least one
Quattro card is present. This breaks when a Quattro card fails
initialization for whatever reason - IRQ is registered and OOPS happens
when it fires.
The solution, as suggested by David Miller, was to keep track which
cards of the Quattro bundles have been initialized, and request/free the
Quattro IRQ only when all four devices have been successfully
initialized.
The patch only touches SBus initialization - PCI init already resets the
card pointer to NULL on init failure.
The patch has been tested on Sun E3500 with SBus and PCI single HME
cards and one PCI Quattro HME card in a situation where any PCI card
failed init when the SBus routines tried to init them by mistake.
Additionally it replaces Quattro request_irq panic with error return -
if this card fails to work, at least let the others work.
Tested on E450 with PCI HME and PCI Quad HME.
[ Minor coding style fixups -DaveM ]
Signed-off-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
Meelis Roos [Wed, 11 Feb 2009 01:19:19 +0000 (17:19 -0800)]
fore200: fix oops on failed firmware load
Fore 200 ATM driver fails to handle request_firmware failures and oopses
when no firmware file was found. Fix it by checking for the right return
values and propaganting the return value up.
Signed-off-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chuck Ebbert [Wed, 11 Feb 2009 01:18:17 +0000 (17:18 -0800)]
pkt_sched: type should be __u32 in header
Using u32 in this header breaks the build of iptables.
Signed-off-by: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rémi Denis-Courmont [Wed, 11 Feb 2009 01:14:50 +0000 (17:14 -0800)]
Phonet: do not compute unused value
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rémi Denis-Courmont [Wed, 11 Feb 2009 01:14:31 +0000 (17:14 -0800)]
Phonet: fix double free in GPRS outbound packet error path
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paulius Zaleckas [Sun, 8 Feb 2009 23:46:01 +0000 (23:46 +0000)]
mdio-gpio: Add mdc pin direction initialization
mdc pin should always be output. Initialize it as output,
so each board code does not need to do this.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Mon, 9 Feb 2009 23:07:18 +0000 (15:07 -0800)]
bridge: Fix LRO crash with tun
> Kernel BUG at drivers/net/tun.c:444
> invalid opcode: 0000 [1] SMP
> last sysfs file: /class/net/lo/ifindex
> CPU 0
> Modules linked in: tun ipt_MASQUERADE iptable_nat ip_nat xt_state ip_conntrack
> nfnetlink ipt_REJECT xt_tcpudp iptable_filter d
> Pid: 6912, comm: qemu-kvm Tainted: G 2.6.18-128.el5 #1
> RIP: 0010:[<
ffffffff886f57b0>] [<
ffffffff886f57b0>]
> :tun:tun_chr_readv+0x2b1/0x3a6
> RSP: 0018:
ffff8102202c5e48 EFLAGS:
00010246
> RAX:
0000000000000000 RBX:
ffff8102202c5e98 RCX:
0000000004010000
> RDX:
ffff810227063680 RSI:
ffff8102202c5e9e RDI:
ffff8102202c5e92
> RBP:
0000000000010ff6 R08:
0000000000000000 R09:
0000000000000001
> R10:
ffff8102202c5e94 R11:
0000000000000202 R12:
ffff8102275357c0
> R13:
ffff81022755e500 R14:
0000000000000000 R15:
ffff8102202c5ef8
> FS:
00002ae4398db980(0000) GS:
ffffffff803ac000(0000) knlGS:
0000000000000000
> CS: 0010 DS: 0000 ES: 0000 CR0:
000000008005003b
> CR2:
00002ae4ab514000 CR3:
0000000221344000 CR4:
00000000000026e0
> Process qemu-kvm (pid: 6912, threadinfo
ffff8102202c4000, task
>
ffff81022e58d820)
> Stack:
00000000498735cb ffff810229d1a3c0 0000000000000000 ffff81022e58d820
>
ffffffff8008a461 ffff81022755e528 ffff81022755e528 ffffffff8009f925
>
000005ea05ea0000 ffff8102209d0000 00001051143e1600 ffffffff8003c00e
> Call Trace:
> [<
ffffffff8008a461>] default_wake_function+0x0/0xe
> [<
ffffffff8009f925>] enqueue_hrtimer+0x55/0x70
> [<
ffffffff8003c00e>] hrtimer_start+0xbc/0xce
> [<
ffffffff886f58bf>] :tun:tun_chr_read+0x1a/0x1f
> [<
ffffffff8000b3f3>] vfs_read+0xcb/0x171
> [<
ffffffff800117d4>] sys_read+0x45/0x6e
> [<
ffffffff8005d116>] system_call+0x7e/0x83
>
>
> Code: 0f 0b 68 40 62 6f 88 c2 bc 01 f6 42 0a 08 74 0c 80 4c 24 41
> RIP [<
ffffffff886f57b0>] :tun:tun_chr_readv+0x2b1/0x3a6
> RSP <
ffff8102202c5e48>
> <0>Kernel panic - not syncing: Fatal exception
This crashed when an LRO packet generated by bnx2x reached a
tun device through the bridge. We're supposed to drop it at
the bridge. However, because the check was placed in br_forward
instead of __br_forward, it's only effective if we are sending
the packet through a single port.
This patch fixes it by moving the check into __br_forward.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Noriaki TAKAMIYA [Mon, 9 Feb 2009 23:01:19 +0000 (15:01 -0800)]
IPv6: fix to set device name when new IPv6 over IPv6 tunnel device is created.
When the user creates IPv6 over IPv6 tunnel, the device name created
by the kernel isn't set to t->parm.name, which is referred as the
result of ioctl().
Signed-off-by: Noriaki TAKAMIYA <takamiya@po.ntts.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jarek Poplawski [Mon, 9 Feb 2009 22:59:30 +0000 (14:59 -0800)]
gianfar: Fix boot hangs while bringing up gianfar ethernet
Ira Snyder found that commit
8c7396aebb68994c0519e438eecdf4d5fa9c7844
"gianfar: Merge Tx and Rx interrupt for scheduling clean up ring" can
cause hangs. It's because there was removed clearing of interrupts in
gfar_schedule_cleanup() (which is called by an interrupt handler) in
case when netif scheduling has been disabled. This patch brings back
this action and a comment.
Reported-by: Ira Snyder <iws@ovro.caltech.edu>
Reported-by: Peter Korsgaard <jacmet@sunsite.dk>
Bisected-by: Ira Snyder <iws@ovro.caltech.edu>
Tested-by: Peter Korsgaard <jacmet@sunsite.dk>
Tested-by: Ira Snyder <iws@ovro.caltech.edu>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Qu Haoran [Mon, 9 Feb 2009 22:34:56 +0000 (14:34 -0800)]
netfilter: xt_sctp: sctp chunk mapping doesn't work
When user tries to map all chunks given in argument, kernel
works on a copy of the chunkmap, but at the end it doesn't
check the copy, but the orginal one.
Signed-off-by: Qu Haoran <haoran.qu@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso [Mon, 9 Feb 2009 22:34:26 +0000 (14:34 -0800)]
netfilter: ctnetlink: fix echo if not subscribed to any multicast group
This patch fixes echoing if the socket that has sent the request to
create/update/delete an entry is not subscribed to any multicast
group. With the current code, ctnetlink would not send the echo
message via unicast as nfnetlink_send() would be skip.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso [Mon, 9 Feb 2009 22:33:57 +0000 (14:33 -0800)]
netfilter: ctnetlink: allow changing NAT sequence adjustment in creation
This patch fixes an inconsistency in the current ctnetlink code
since NAT sequence adjustment bit can only be updated but not set
in the conntrack entry creation.
This patch is used by conntrackd to successfully recover newly
created entries that represent connections with helpers and NAT
payload mangling.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Leblond [Mon, 9 Feb 2009 22:33:20 +0000 (14:33 -0800)]
netfilter: nf_conntrack_ipv6: don't track ICMPv6 negotiation message
This patch removes connection tracking handling for ICMPv6 messages
related to Stateless Address Autoconfiguration, MLD, and MLDv2. They
can not be tracked because they are massively using multicast (on
pre-defined address). But they are not invalid and should not be
detected as such.
Signed-off-by: Eric Leblond <eric@inl.fr>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Leblond [Mon, 9 Feb 2009 22:33:03 +0000 (14:33 -0800)]
netfilter: fix tuple inversion for Node information request
The patch fixes a typo in the inverse mapping of Node Information
request. Following draft-ietf-ipngwg-icmp-name-lookups-09, "Querier"
sends a type 139 (ICMPV6_NI_QUERY) packet to "Responder" which answer
with a type 140 (ICMPV6_NI_REPLY) packet.
Signed-off-by: Eric Leblond <eric@inl.fr>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dhananjay Phadke [Mon, 9 Feb 2009 03:20:19 +0000 (19:20 -0800)]
netxen: fix msi-x interrupt handling
o Cut down msi-x vectors from 8 to 1 since only one is used for now.
o Use separate handler for msi-x, that doesn't unnecessarily scrub
msi status register.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Risto Suominen [Mon, 9 Feb 2009 01:50:34 +0000 (17:50 -0800)]
de2104x: force correct order when writing to rx ring
DescOwn should not be set, thus allowing the chip to use the
descriptor, before everything else is set up correctly.
Signed-off-by: Risto Suominen <Risto.Suominen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Williamson [Mon, 9 Feb 2009 01:49:17 +0000 (17:49 -0800)]
tun: Fix unicast filter overflow
Tap devices can make use of a small MAC filter set via the
TUNSETTXFILTER ioctl. The filter has a set of exact matches
plus a hash for imperfect filtering of additional multicast
addresses. The current code is unbalanced, adding unicast
addresses to the multicast hash, but only checking the hash
against multicast addresses. This results in the filter
dropping unicast addresses that overflow the exact filter.
The fix is simply to disable the filter by leaving count set
to zero if we find non-multicast addresses after the exact
match table is filled.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julia Lawall [Mon, 9 Feb 2009 01:00:49 +0000 (17:00 -0800)]
drivers/isdn: introduce missing kfree
Error handling code following a kmalloc should free the allocated data.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,l;
position p1,p2;
expression *ptr != NULL;
@@
(
if ((x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...)) == NULL) S
|
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
)
<... when != x
when != if (...) { <+...x...+> }
x->f = E
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julia Lawall [Mon, 9 Feb 2009 01:00:02 +0000 (17:00 -0800)]
drivers/atm: introduce missing kfree
Error handling code following a kmalloc should free the allocated data.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,l;
position p1,p2;
expression *ptr != NULL;
@@
(
if ((x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...)) == NULL) S
|
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
)
<... when != x
when != if (...) { <+...x...+> }
x->f = E
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 7 Feb 2009 10:20:25 +0000 (02:20 -0800)]
sunhme: Don't match PCI devices in SBUS probe.
Unfortunately, the OF device tree nodes for SBUS and PCI
hme devices have the same device node name on some systems.
So if the name of the parent node isn't 'sbus', skip it.
Based upon an excellent report and detective work by
Meelis Roos and Eric Brower.
Signed-off-by: David S. Miller <davem@davemloft.net>
Tested-by: Meelis Roos <mroos@linux.ee>
Eric Van Hensbergen [Sat, 7 Feb 2009 06:07:41 +0000 (22:07 -0800)]
9p: fix endian issues [attempt 3]
When the changes were done to the protocol last release, some endian
bugs crept in. This patch fixes those endian problems and has been
verified to run on 32/64 bit and x86/ppc architectures.
This version of the patch incorporates the correct annotations
for endian variables.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 7 Feb 2009 06:06:43 +0000 (22:06 -0800)]
net_dma: call dmaengine_get only if NET_DMA enabled
Based upon a patch from Atsushi Nemoto <anemo@mba.ocn.ne.jp>
--------------------
The commit
649274d993212e7c23c0cb734572c2311c200872 ("net_dma:
acquire/release dma channels on ifup/ifdown") added unconditional call
of dmaengine_get() to net_dma. The API should be called only if
NET_DMA was enabled.
--------------------
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Ondrej Zary [Sat, 7 Feb 2009 06:04:08 +0000 (22:04 -0800)]
3c509: Fix resume from hibernation for PnP mode.
From: Ondrej Zary <linux@rainbow-software.org>
last year, I posted a patch which fixed hibernation on 3c509
cards. That was back in 2.6.24. It worked fine in 2.6.25. But then I
stopped using hibernation (as it did not work with my new IT8212 RAID
controller).
Now I fixed it and noticed that 3c509 does not wake up properly
anymore (in 2.6.28) - neither in PnP nor in ISA modes. ifconfig
down/up makes the card work again in PnP mode. However, in ISA mode,
ifconfig up ends with "No such device" error.
Comparing the 3c509 driver between 2.6.25 and 2.6.28, there's only
some statistics-related change. So the cause of the problem must be
somewhere else.
This patch makes the resume work in PnP mode, but it's still not
enough for ISA mode.
Signed-off-by: David S. Miller <davem@davemloft.net>
Ilkka Virta [Sat, 7 Feb 2009 06:00:36 +0000 (22:00 -0800)]
sungem: Soft lockup in sungem on Netra AC200 when switching interface up
From: Ilkka Virta <itvirta@iki.fi>
In the lockup situation the driver seems to go off in an eternal storm
of interrupts right after calling request_irq(). It doesn't actually
do anything interesting in the interrupt handler. Since connecting the link
afterwards works, something later in initialization must fix this.
Looking at gem_do_start() and gem_open(), it seems that the only thing
done while opening the device after the request_irq(), is a call to
napi_enable().
I don't know what the ordering requirements are for the
initialization, but I boldly tried to move the napi_enable() call
inside gem_do_start() before the link state is checked and interrupts
subsequently enabled, and it seems to work for me. Doesn't even break
anything too obvious...
Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Sat, 7 Feb 2009 05:50:52 +0000 (21:50 -0800)]
RxRPC: Fix a potential NULL dereference
Fix a potential NULL dereference bug during error handling in
rxrpc_kernel_begin_call(), whereby rxrpc_put_transport() may be handed a NULL
pointer.
This was found with a code checker (http://repo.or.cz/w/smatch.git/).
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Vecera [Sat, 7 Feb 2009 05:49:57 +0000 (21:49 -0800)]
r8169: Don't update statistics counters when interface is down
Some Realtek chips (RTL8169sb/8110sb in my case) are unable to retrieve
ethtool statistics when the interface is down. The process stays in
endless loop in rtl8169_get_ethtool_stats. This is because these chips
need to have receiver enabled (CmdRxEnb bit in ChipCmd register) that is
cleared when the interface is going down. It's better to update statistics
only when the interface is up and otherwise return copy of statistics
grabbed when the interface was up (in rtl8169_close).
It is interesting that PCI-E NICs (like 8168b/8111b...) are not affected.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesper Dangaard Brouer [Fri, 6 Feb 2009 09:59:12 +0000 (01:59 -0800)]
udp: Fix potential wrong ip_hdr(skb) pointers
Like the UDP header fix, pskb_may_pull() can potentially
alter the SKB buffer. Thus the saddr and daddr, pointers
may point to the old skb->data buffer.
I haven't seen corruptions, as its only seen if the old
skb->data buffer were reallocated by another user and
written into very quickly (or poison'd by SLAB debugging).
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gautam Kachroo [Fri, 6 Feb 2009 08:52:04 +0000 (00:52 -0800)]
neigh: some entries can be skipped during dumping
neightbl_dump_info and neigh_dump_table can skip entries if the
*fill*info functions return an error. This results in an incomplete
dump ((invoked by netlink requests for RTM_GETNEIGHTBL or
RTM_GETNEIGH)
nidx and idx should not be incremented if the current entry was not
placed in the output buffer
Signed-off-by: Gautam Kachroo <gk@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 6 Feb 2009 08:49:55 +0000 (00:49 -0800)]
ipv6: Disallow rediculious flowlabel option sizes.
Just like PKTINFO, limit the options area to 64K.
Based upon report by Eric Sesterhenn and analysis by
Roland Dreier.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 5 Feb 2009 23:38:31 +0000 (15:38 -0800)]
Revert "tcp: Always set urgent pointer if it's beyond snd_nxt"
This reverts commit
64ff3b938ec6782e6585a83d5459b98b0c3f6eb8.
Jeff Chua reports that it breaks rlogin for him.
Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Thu, 5 Feb 2009 23:15:50 +0000 (15:15 -0800)]
ipv6: Copy cork options in ip6_append_data
As the options passed to ip6_append_data may be ephemeral, we need
to duplicate it for corking. This patch applies the simplest fix
which is to memdup all the relevant bits.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 5 Feb 2009 23:08:11 +0000 (15:08 -0800)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6
Jesper Dangaard Brouer [Thu, 5 Feb 2009 23:05:45 +0000 (15:05 -0800)]
udp: Fix UDP short packet false positive
The UDP header pointer assignment must happen after calling
pskb_may_pull(). As pskb_may_pull() can potentially alter the SKB
buffer.
This was exposted by running multicast traffic through the NIU driver,
as it won't prepull the protocol headers into the linear area on
receive.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Fleming [Thu, 5 Feb 2009 00:38:05 +0000 (16:38 -0800)]
gianfar: Fix potential soft reset race
SOFT_RESET must be asserted for at least 3 TX clocks in order for it to work
properly. The syncs in the gfar_write() commands have been hiding this, but
we need to guarantee it.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Fleming [Thu, 5 Feb 2009 00:37:40 +0000 (16:37 -0800)]
gianfar: Fix BD_LENGTH_MASK definition
BD_LENGTH_MASK is supposed to catch the low 16-bits of the status field, not
the low byte. The old way, we would never be able to clean up tx packets with
sizes divisible by 256.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Divy Le Ray [Thu, 5 Feb 2009 00:31:39 +0000 (16:31 -0800)]
cxgb3: Fix lro switch
The LRO switch is always set to 1 in the rx processing loop.
It breaks the accelerated iSCSI receive traffic.
Fix its computation.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reinette Chatre [Tue, 3 Feb 2009 18:20:03 +0000 (10:20 -0800)]
iwlwifi: save PCI state before suspend, restore after resume
This is the right thing to do and fixes the following warning:
[ 115.012278] ------------[ cut here ]------------
[ 115.012281] WARNING: at drivers/pci/pci-driver.c:370
pci_legacy_suspend+0x85/0xc2()
[ 115.012285] Hardware name: Latitude D630
[ 115.012301] PCI PM: Device state not saved by
iwl3945_pci_suspend+0x0/0x4c [iwl3945]
[ 115.012304] Modules linked in: fuse nfsd lockd nfs_acl auth_rpcgss
exportfs sunrpc ipv6 acpi_cpufreq kvm_intel kvm snd_hda_codec_idt
snd_hda_intel snd_hda_codec snd_hwdep arc4 snd_seq_device snd_pcm_oss
snd_mixer_oss ecb snd_pcm cryptomgr aead snd_timer crypto_blkcipher
snd snd_page_alloc ohci1394 crypto_hash crypto_algapi ch341 ieee1394
usbserial thermal iwl3945 mac80211 led_class lib80211 tg3 processor
i2c_i801 i2c_core sg cfg80211 libphy usbhid battery ac button sr_mod
cdrom evdev dcdbas ata_generic ata_piix libata sd_mod scsi_mod ext3
jbd mbcache uhci_hcd ohci_hcd ehci_hcd usbcore [last unloaded:
microcode]
[ 115.012374] Pid: 4163, comm: pm-suspend Not tainted
2.6.29-rc3-00227-gf1dd849-dirty #67
[ 115.012377] Call Trace:
[ 115.012382] [<
ffffffff8023d04d>] warn_slowpath+0xb1/0xed
[ 115.012387] [<
ffffffff80450b5e>] ? _spin_unlock_irqrestore+0x5c/0x78
[ 115.012390] [<
ffffffff80254f08>] ? up+0x34/0x39
[ 115.012394] [<
ffffffff80362319>] ? acpi_ut_release_mutex+0x5d/0x61
[ 115.012397] [<
ffffffff803584b2>] ? acpi_get_data+0x5e/0x70
[ 115.012400] [<
ffffffff80363dd9>] ? acpi_bus_get_device+0x25/0x39
[ 115.012403] [<
ffffffff80363e98>] ? acpi_bus_power_manageable+0x11/0x29
[ 115.012406] [<
ffffffff803462f7>] ? acpi_pci_power_manageable+0x17/0x19
[ 115.012410] [<
ffffffff8033ddfd>] ? pci_set_power_state+0xcc/0x101
[ 115.012418] [<
ffffffffa01f28e9>] ? iwl3945_pci_suspend+0x0/0x4c [iwl3945]
[ 115.012422] [<
ffffffff803401e6>] pci_legacy_suspend+0x85/0xc2
[ 115.012425] [<
ffffffff80340316>] pci_pm_suspend+0x34/0x86
[ 115.012429] [<
ffffffff8039d7ce>] pm_op+0x52/0xe5
[ 115.012432] [<
ffffffff8039dd78>] device_suspend+0x32a/0x451
[ 115.012436] [<
ffffffff80269ec2>] suspend_devices_and_enter+0x3e/0x13a
[ 115.012439] [<
ffffffff8026a128>] enter_state+0x110/0x164
[ 115.012442] [<
ffffffff8026a233>] state_store+0xb7/0xd7
[ 115.012446] [<
ffffffff8032f95f>] kobj_attr_store+0x17/0x19
[ 115.012449] [<
ffffffff80307d64>] sysfs_write_file+0xe4/0x119
[ 115.012453] [<
ffffffff802baa7a>] vfs_write+0xae/0x137
[ 115.012456] [<
ffffffff802babc7>] sys_write+0x47/0x70
[ 115.012459] [<
ffffffff8020b73a>] system_call_fastpath+0x16/0x1b
[ 115.012467] ---[ end trace
829828966f6f24dc ]---
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Ming Lei <tom.leiming@gmail.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reinette Chatre [Wed, 28 Jan 2009 17:38:30 +0000 (09:38 -0800)]
iwlwifi: clean key table in iwl_clear_stations_table
Cleans uCode key table bit map iwl_clear_stations_table
since all stations are cleared also the key table must be.
Since the keys are not removed properly on suspend by mac80211
this may result in exhausting key table on resume leading
to memory corruption during removal
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Randy Dunlap [Tue, 3 Feb 2009 23:20:13 +0000 (15:20 -0800)]
sunrpc: fix rdma dependencies
Fix sunrpc/rdma build dependencies.
Survives 12 build combinations of INET, IPV6, SUNRPC,
INFINIBAND, and INFINIBAND_ADDR_TRANS.
ERROR: "rdma_destroy_id" [net/sunrpc/xprtrdma/xprtrdma.ko] undefined!
ERROR: "rdma_connect" [net/sunrpc/xprtrdma/xprtrdma.ko] undefined!
ERROR: "rdma_destroy_qp" [net/sunrpc/xprtrdma/xprtrdma.ko] undefined!
ERROR: "rdma_create_id" [net/sunrpc/xprtrdma/xprtrdma.ko] undefined!
ERROR: "rdma_create_qp" [net/sunrpc/xprtrdma/xprtrdma.ko] undefined!
ERROR: "rdma_resolve_route" [net/sunrpc/xprtrdma/xprtrdma.ko] undefined!
ERROR: "rdma_disconnect" [net/sunrpc/xprtrdma/xprtrdma.ko] undefined!
ERROR: "rdma_resolve_addr" [net/sunrpc/xprtrdma/xprtrdma.ko] undefined!
ERROR: "rdma_accept" [net/sunrpc/xprtrdma/svcrdma.ko] undefined!
ERROR: "rdma_destroy_id" [net/sunrpc/xprtrdma/svcrdma.ko] undefined!
ERROR: "rdma_listen" [net/sunrpc/xprtrdma/svcrdma.ko] undefined!
ERROR: "rdma_create_id" [net/sunrpc/xprtrdma/svcrdma.ko] undefined!
ERROR: "rdma_create_qp" [net/sunrpc/xprtrdma/svcrdma.ko] undefined!
ERROR: "rdma_bind_addr" [net/sunrpc/xprtrdma/svcrdma.ko] undefined!
ERROR: "rdma_disconnect" [net/sunrpc/xprtrdma/svcrdma.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Karsten Keil [Tue, 3 Feb 2009 23:18:01 +0000 (15:18 -0800)]
e1000: Fix PCI enable to honor the need_ioport flag
On machine were no IO ports are assigned the call
to pci_enable_device() will fail, even if need_ioport
is false, we need to use pci_enable_device_mem() here.
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dean Nelson [Tue, 3 Feb 2009 23:16:17 +0000 (15:16 -0800)]
sgi-xp: link XPNET's net_device_ops to its net_device structure
A recent patch by Stephen Hemminger to convert XPNET to use net_device_ops and
internal net_device_stats failed to link the net_device_ops structure to the
net_device structure. See commit
e8ac9c55f28482f5b2f497a8e7eb90985db237c2
("xpnet: convert devices to new API").
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cord Walter [Tue, 3 Feb 2009 23:14:05 +0000 (15:14 -0800)]
pcnet_cs: Fix misuse of the equality operator.
Signed-off-by: Cord Walter <qord@cwalter.net>
Signed-off-by: Komuro <komurojun-mbn@nifty.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Filip Aben [Tue, 3 Feb 2009 23:13:26 +0000 (15:13 -0800)]
hso: add new device id's
This patch adds a few device ID's. It also removes an ID that was used
in an internal engineering version of a device and will never see
commercial light. Even if this ID will be 'recycled' in the future,
which is very unlikely, we don't know what kind of device will be
behind it. Therefore it's safer to remove it.
Signed-off-by: Filip Aben <f.aben@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 3 Feb 2009 07:55:27 +0000 (23:55 -0800)]
Merge branch 'master' of /linux/kernel/git/torvalds/linux-2.6
Maciej Sosnowski [Tue, 3 Feb 2009 07:26:57 +0000 (23:26 -0800)]
dca: redesign locks to fix deadlocks
Change spin_locks to irqsave to prevent dead-locks.
Protect adding and deleting to/from dca_providers list.
Drop the lock during dca_sysfs_add_req() and dca_sysfs_remove_req() calls
as they might sleep (use GFP_KERNEL allocation).
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roel Kluin [Tue, 3 Feb 2009 07:19:50 +0000 (23:19 -0800)]
cassini/sungem: limit reaches -1, but 0 tested
while (limit--)
if (test())
break;
if (limit <= 0)
goto test_failed;
In the last iteration, limit is decremented after the test to 0.
If just thereafter test() succeeds and a break occurs, the goto
still occurs because limit is 0.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roel Kluin [Tue, 3 Feb 2009 05:39:02 +0000 (21:39 -0800)]
net: variables reach -1, but 0 tested
while (timeout--) { ... }
timeout becomes -1 if the loop isn't ended otherwise, not 0.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 3 Feb 2009 03:28:58 +0000 (19:28 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jbarnes/pci-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI hotplug: Change link order of pciehp & acpiphp
PCI hotplug: fakephp: Allocate PCI resources before adding the device
PCI MSI: Fix undefined shift by 32
PCI PM: Do not wait for buses in B2 or B3 during resume
PCI PM: Power up devices before restoring their state
PCI PM: Fix hibernation breakage on EeePC 701
PCI: irq and pci_ids patch for Intel Tigerpoint DeviceIDs
PCI PM: Fix suspend error paths and testing facility breakage
Linus Torvalds [Tue, 3 Feb 2009 03:27:00 +0000 (19:27 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/penberg/slab-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
slub: fix per cpu kmem_cache_cpu array memory leak
kmalloc: return NULL instead of link failure
Linus Torvalds [Tue, 3 Feb 2009 03:26:44 +0000 (19:26 -0800)]
Merge branch 'merge' of git://git./linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
fbdev/atyfb: Fix DSP config on some PowerMacs & PowerBooks
powerpc: Fix oops on some machines due to incorrect pr_debug()
powerpc/ps3: Printing fixups for l64 to ll64 convserion drivers/net
powerpc/5200: update device tree binding documentation
powerpc/5200: Bugfix for PCI mapping of memory and IMMR
powerpc/5200: update defconfigs
Linus Torvalds [Tue, 3 Feb 2009 03:26:29 +0000 (19:26 -0800)]
Merge branch 'sched-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched_rt: don't use first_cpu on cpumask created with cpumask_and
sched: fix buddie group latency
sched: clear buddies more aggressively
sched: symmetric sync vs avg_overlap
sched: fix sync wakeups
cpuset: fix possible deadlock in async_rebuild_sched_domains
Linus Torvalds [Tue, 3 Feb 2009 03:26:06 +0000 (19:26 -0800)]
Merge branch 'for_linus' of git://git./linux/kernel/git/mchehab/linux-2.6
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (45 commits)
V4L/DVB (10411): s5h1409: Perform s5h1409 soft reset after tuning
V4L/DVB (10403): saa7134-alsa: saa7130 doesn't support digital audio
V4L/DVB (10229): ivtv: fix memory leak
V4L/DVB (10385): gspca - main: Fix memory leak when USB disconnection while streaming.
V4L/DVB (10325): em28xx: Fix for fail to submit URB with IRQs and Pre-emption Disabled
V4L/DVB (10317): radio-mr800: fix radio->muted and radio->stereo
V4L/DVB (10314): cx25840: ignore TUNER_SET_CONFIG in the command callback.
V4L/DVB (10288): af9015: bug fix: stick does not work always when plugged
V4L/DVB (10287): af9015: fix second FE
V4L/DVB (10270): saa7146: fix unbalanced mutex_lock/unlock
V4L/DVB (10265): budget.c driver: Kernel oops: "BUG: unable to handle kernel paging request at
ffffffff
V4L/DVB (10261): em28xx: fix kernel panic on audio shutdown
V4L/DVB (10257): em28xx: Fix for KWorld 330U Board
V4L/DVB (10256): em28xx: Fix for KWorld 330U AC97
V4L/DVB (10254): em28xx: Fix audio URB transfer buffer race condition
V4L/DVB (10250): cx25840: fix regression: fw not loaded on first use
V4L/DVB (10248): v4l-dvb: fix a bunch of compile warnings.
V4L/DVB (10243): em28xx: fix compile warning
V4L/DVB (10240): Fix obvious swapped names in v4l2_subdev logic
V4L/DVB (10233): [PATCH] Terratec Cinergy DT XS Diversity new USB ID (0ccd:0081)
...
Linus Torvalds [Tue, 3 Feb 2009 03:24:14 +0000 (19:24 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/drzeus/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
pxamci: enable DMA for write ops after CMD/RESP
pxamci: replace #ifdef CONFIG_PXA27x with if (cpu_is_pxa27x())
ricoh_mmc: Use suspend_late/resume_early
mmci: Add support for ST Micro derivate
mmc: Add a MX2/MX3 specific SDHC driver
Linus Torvalds [Tue, 3 Feb 2009 03:23:49 +0000 (19:23 -0800)]
Merge git://git./linux/kernel/git/bart/ide-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
icside: fix PCB version 6 support (v2)
tx4939ide: typo fix and minor cleanup
ide: add CS5536 host driver (v3)
ide: Force VIA IDE legacy interrupts for AmigaOne boards
IDE: Unregister and disable devices if initialization fails.
ide: fix ide_register_port() failure handling
ide: struct device - replace bus_id with dev_name(), dev_set_name()
ide-cd: fix DMA for non bio-backed requests
Linus Torvalds [Tue, 3 Feb 2009 03:20:17 +0000 (19:20 -0800)]
Merge branch 'for-upstream' of git://git./linux/kernel/git/dvrabel/uwb
* 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/dvrabel/uwb:
uwb: lock rc->rsvs_lock with spin_lock_bh()
wusb: timeout when waiting for ASL/PZL updates in whci-hcd
uwb: remove unused #include <version.h>'s
wusb: return -ENOTCONN when resetting a port with no connected device
uwb: safely remove all reservations
Linus Torvalds [Tue, 3 Feb 2009 03:19:50 +0000 (19:19 -0800)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: add text file detailing queue/ sysfs files
bio.h: If they MUST be inlined, then use __always_inline
Fix misleading comment in bio.h
block: fix inconsistent parenthesisation of QUEUE_FLAG_DEFAULT
block: fix oops in blk_queue_io_stat()
Mark McLoughlin [Tue, 3 Feb 2009 03:03:53 +0000 (13:33 +1030)]
virtio-pci: do not oops on config change if driver not loaded
The host really shouldn't be notifying us of config changes
before the device status is VIRTIO_CONFIG_S_DRIVER or
VIRTIO_CONFIG_S_DRIVER_OK.
However, if we do happen to be interrupted while we're not
attached to a driver, we really shouldn't oops. Prevent
this simply by checking that device->driver is non-NULL
before trying to notify the driver of config changes.
Problem observed by doing a "set_link virtio.0 down" with
QEMU before the net driver had been loaded.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eric Dumazet [Tue, 3 Feb 2009 03:01:36 +0000 (13:31 +1030)]
modules: Use a better scheme for refcounting
Current refcounting for modules (done if CONFIG_MODULE_UNLOAD=y) is
using a lot of memory.
Each 'struct module' contains an [NR_CPUS] array of full cache lines.
This patch uses existing infrastructure (percpu_modalloc() &
percpu_modfree()) to allocate percpu space for the refcount storage.
Instead of wasting NR_CPUS*128 bytes (on i386), we now use
nr_cpu_ids*sizeof(local_t) bytes.
On a typical distro, where NR_CPUS=8, shiping 2000 modules, we reduce
size of module files by about 2 Mbytes. (1Kb per module)
Instead of having all refcounters in the same memory node - with TLB misses
because of vmalloc() - this new implementation permits to have better
NUMA properties, since each CPU will use storage on its preferred node,
thanks to percpu storage.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ron Mercer [Mon, 2 Feb 2009 21:54:31 +0000 (13:54 -0800)]
qlge: bugfix: Add missing netif_napi_del call.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ron Mercer [Mon, 2 Feb 2009 21:54:15 +0000 (13:54 -0800)]
qlge: bugfix: Add flash offset for second port.
Without this the 2nd port gets first ports MAC addr.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ron Mercer [Mon, 2 Feb 2009 21:53:57 +0000 (13:53 -0800)]
qlge: bugfix: Fix endian issue when reading flash.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 2 Feb 2009 21:41:57 +0000 (13:41 -0800)]
udp: increments sk_drops in __udp_queue_rcv_skb()
Commit
93821778def10ec1e69aa3ac10adee975dad4ff3 (udp: Fix rcv socket
locking) accidentally removed sk_drops increments for UDP IPV4
sockets.
This field can be used to detect incorrect sizing of socket receive
buffers.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 2 Feb 2009 21:27:44 +0000 (13:27 -0800)]
net: Fix userland breakage wrt. linux/if_tunnel.h
Reported by Andrew Walrond <andrew@walrond.org>
Changeset
c19e654ddbe3831252f61e76a74d661e1a755530
("gre: Add netlink interface") added an include
of linux/ip.h to linux/if_tunnel.h
We can't really let that get exposed to userspace
because this conflicts with types defined in netinet/ip.h
which userland is almost certainly going to have included
either explicitly or implicitly.
So guard this include with a __KERNEL__ ifdef.
Signed-off-by: David S. Miller <davem@davemloft.net>
Cliff Brake [Thu, 22 Jan 2009 22:07:03 +0000 (17:07 -0500)]
pxamci: enable DMA for write ops after CMD/RESP
With the PXA270 MMC hardware, there seems to be an issue of
data corruption on writes where a 4KB data block is offset
by one byte.
If we delay enabling the DMA for writes until after the CMD/RESP
has finished, the problem seems to be fixed.
related to PXA270 Erratum #91
Tested-by: Vernon Sauder <VernonInHand@gmail.com>
Signed-off-by: Cliff Brake <cbrake@bec-systems.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Cliff Brake [Thu, 22 Jan 2009 21:58:58 +0000 (16:58 -0500)]
pxamci: replace #ifdef CONFIG_PXA27x with if (cpu_is_pxa27x())
Signed-off-by: Cliff Brake <cbrake@bec-systems.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
philipl@overt.org [Sun, 18 Jan 2009 19:11:20 +0000 (14:11 -0500)]
ricoh_mmc: Use suspend_late/resume_early
If ricoh_mmc suspends before sdhci_pci, it will pull the card
out from under the controller, which could leave the system in
a very confused state.
Using suspend_late/resume_early ensures that sdhci_pci suspends first
and resumes second.
Signed-off-by: Philip Langdale <philipl@overt.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Linus Walleij [Sun, 4 Jan 2009 14:18:54 +0000 (15:18 +0100)]
mmci: Add support for ST Micro derivate
This patch adds support for the ST Microelectronics version of
the PL180 PrimeCell. They use designer ID 0x80 and have a few
alterations/bugfixes related to open drain and HW flow control.
They also add some SDIO registers, I am unsure if these are
in ST HW only or if this is things also added in later ARM
revisions, but they are included in the mmci.h file for
completeness.
Signed-off-by: Linus Walleij <linus.walleij@ericsson.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Sascha Hauer [Tue, 6 Jan 2009 16:04:14 +0000 (17:04 +0100)]
mmc: Add a MX2/MX3 specific SDHC driver
This patch adds a MX2/MX3 specific SDHC driver. The hardware is basically
the same as in the MX1, but unlike the MX1 controller the MX2
controller just works as expected. Since the MX1 driver has more
workarounds for bugs than anything else I had no success with supporting
MX1 and MX2 in a sane way in one driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Bartlomiej Zolnierkiewicz [Mon, 2 Feb 2009 19:12:23 +0000 (20:12 +0100)]
icside: fix PCB version 6 support (v2)
We need to pass struct ide_port_info also to ide_host_register().
v2:
Fix v5/v6 mismatch noticed by Russell.
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Atsushi Nemoto [Mon, 2 Feb 2009 19:12:23 +0000 (20:12 +0100)]
tx4939ide: typo fix and minor cleanup
The bcount is greater than 0 and less than or equal to 0x10000.
Thus '(bcount & 0xffff) == 0x0000' can be simplified as 'bcount == 0x10000'.
Suggested-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Mon, 2 Feb 2009 19:12:23 +0000 (20:12 +0100)]
ide: add CS5536 host driver (v3)
This is a port of libata's pata_cs5536.c (written by Martin K. Petersen)
to IDE subsystem.
Changes done while at it:
* Reprogram PIO/MWDMA timings if needed before and after DMA transfer
(chipset uses shared PIO/MWDMA timings).
* Fix cable detection to report 80-wires cable if BIOS set it for any
device on a port (IDE core will do drive-side cable detection later).
* Don't disable UDMA while programming PIO timings.
* Simplify PCI/MSR support.
Pros of having IDE host driver in addition to libata's one:
* IDE is much lighter than SCSI+libata, the host driver itself is also
a bit smaller:
text data bss dec hex filename
1261 496 4 1761 6e1 drivers/ata/pata_cs5536.o
1242 128 4 1374 55e drivers/ide/cs5536.o
* This allows use of IDE features which are unavailable under libata.
v2:
* Fixes per review from Sergei:
- simplify dependency check in Kconfig
- use IDE_DRV_MASK also for ->drive_data
- disable UDMA when programming MWDMA
- program new DTC timings only when necessary
- fix printk() level in cs5536_init_one()
* Fix patch description according to comments from Alan and Sergei.
v3:
* Smarter masking of UDMA bits per Sergei's suggestion.
Cc: Martin K. Petersen <mkp@mkp.net>
Cc: Karl Auerbach <karl@iwl.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Gerhard Pircher [Mon, 2 Feb 2009 19:12:22 +0000 (20:12 +0100)]
ide: Force VIA IDE legacy interrupts for AmigaOne boards
The AmigaOne uses the onboard VIA IDE controller in legacy mode (like the
Pegasos).
Signed-off-by: Gerhard Pircher <gerhard_pircher@gmx.net>
Cc: "Grant Likely" <grant.likely@secretlab.ca>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Ian Campbell [Mon, 2 Feb 2009 19:12:22 +0000 (20:12 +0100)]
IDE: Unregister and disable devices if initialization fails.
On reboot the loop in device_shutdown gets confused by these partially
initialized devices and goes into an infinite loop. Therefore unregister
and disable these devices.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
[bart: remove leftover hwif->present clearing + update patch description]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Mon, 2 Feb 2009 19:12:21 +0000 (20:12 +0100)]
ide: fix ide_register_port() failure handling
* Factor out port freeing from ide_host_free() to ide_free_port().
* Add ide_disable_port() and use it on ide_register_port() failure.
Cc: Ian Campbell <Ian.Campbell@citrix.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Kay Sievers [Mon, 2 Feb 2009 19:12:21 +0000 (20:12 +0100)]
ide: struct device - replace bus_id with dev_name(), dev_set_name()
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: linux-ide@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Borislav Petkov [Mon, 2 Feb 2009 19:12:21 +0000 (20:12 +0100)]
ide-cd: fix DMA for non bio-backed requests
This one fixes http://bugzilla.kernel.org/show_bug.cgi?id=12320.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
David Vrabel [Mon, 2 Feb 2009 17:52:39 +0000 (17:52 +0000)]
Merge branch 'master' of git://git./linux/kernel/git/torvalds/linux-2.6 into for-upstream
Jens Axboe [Mon, 2 Feb 2009 12:02:31 +0000 (13:02 +0100)]
block: add text file detailing queue/ sysfs files
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Alberto Bertogli [Mon, 2 Feb 2009 11:41:07 +0000 (12:41 +0100)]
bio.h: If they MUST be inlined, then use __always_inline
bvec_kmap_irq() and bvec_kunmap_irq() comments say they MUST be inlined,
so mark them as __always_inline.
Signed-off-by: Alberto Bertogli <albertito@blitiri.com.ar>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Alberto Bertogli [Mon, 2 Feb 2009 11:41:07 +0000 (12:41 +0100)]
Fix misleading comment in bio.h
The comment says "remember to add offset!", but the function already adds
it.
Signed-off-by: Alberto Bertogli <albertito@blitiri.com.ar>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Pekka Enberg [Mon, 2 Feb 2009 09:18:49 +0000 (11:18 +0200)]
Merge branches 'topic/slab/fixes' and 'topic/slub/fixes' into for-linus
Jens Axboe [Mon, 2 Feb 2009 07:43:48 +0000 (08:43 +0100)]
block: fix inconsistent parenthesisation of QUEUE_FLAG_DEFAULT
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Jens Axboe [Mon, 2 Feb 2009 07:42:32 +0000 (08:42 +0100)]
block: fix oops in blk_queue_io_stat()
Some initial probe requests don't have disk->queue mapped yet, so we
can't rely on a non-NULL queue in blk_queue_io_stat(). Wrap it in
blk_do_io_stat().
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Risto Suominen [Tue, 13 Jan 2009 20:09:30 +0000 (20:09 +0000)]
fbdev/atyfb: Fix DSP config on some PowerMacs & PowerBooks
Since the complete re-write in 2.6.10, some PowerMacs (At least PowerMac 5500
and PowerMac G3 Beige rev A) with ATI Mach64 chip have suffered from unstable
columns in their framebuffer image. This seems to depend on a value (4) read
from PLL_EXT_CNTL register, which leads to incorrect DSP config parameters to
be written to the chip. This patch uses a value calculated by aty_init_pll_ct
instead, as a starting point.
There are questions as to whether this should be extended to other platforms
or maybe made dependent on specific chip types, but in the meantime, this has
been tested on various powermacs and works for them so let's commit it.
Signed-off-by: Risto Suominen <Risto.Suominen@gmail.com>
Tested-by: Michael Pettersson <mike@it.uu.se>
Cc: <stable@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Benjamin Herrenschmidt [Sun, 1 Feb 2009 17:03:59 +0000 (17:03 +0000)]
powerpc: Fix oops on some machines due to incorrect pr_debug()
Recently, a patch left DEBUG enabled in the powerpc common PCI code,
resulting in an old bug in a pr_debug() statement to show up and cause
a NULL dereference on some machines.
This fixes the pr_debug() statement and reverts to DEBUG not being
force-enabled in that file.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>