drm/i915/selftests: Flush old resets between engines

When injecting rapid resets, we must be careful to at least wait for the
previous reset to have taken effect and the engine restarted. If we
perform a second reset before that has happened, we will notice that the
engine hasn't recovered and declare it lost, wedging the device and
failing. In practice, since we wait for each hanging batch to start
before injecting the reset, this too-fast-reset condition can only be
triggered when moving onto the next engine in the test, so we need only
wait for the existing reset to complete before switching engines.

v2: Wrap up the wait inside a safety net to bail out in case of angry hw.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180205152431.12163-1-chris@chris-wilson.co.uk

drm/i915/breadcrumbs: Drop request reference for the signaler thread

If we remember to cancel the signaler on a request when retiring it
(after we know that the request has been signaled), we do not need to
carry an additional request in the signaler itself. This prevents an
issue whereby the signaler threads may be delayed and hold on to
thousands of request references, causing severe memory fragmentation and
premature oom (most noticeable on 32b snb due to the limited GFP_KERNEL
and frequent use of inter-engine fences).

v2: Rename first_signal(), document reads outside of locks.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180203101914.24880-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

drm/i915: Remove unbannable context spam from reset

During testing, we trigger a lot of resets on an unbannable context
leading to massive amounts of irrelevant debug spam. Remove the
ban_score accounting and message for the unbannable context so that we
improve the signal:noise in the log messages for when the unexpected
occurs.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180205092201.19476-7-chris@chris-wilson.co.uk

drm/i915/execlists: Remove the startup spam

Execlists is now enabled by default and included in the list of
capabilities printed out to dmesg and beyond. We do not need to mention
it again, every time we restart the engine, so kill the spam.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180205092201.19476-6-chris@chris-wilson.co.uk

drm/i915: Show the GPU state when declaring wedged

Dump each engine state when i915_gem_set_wedged() is called to give us
some more clues as to why we had to terminate the GPU.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180205092201.19476-5-chris@chris-wilson.co.uk

drm/i915: Always update the no_fbc_reason when disabling

Provide the reason why we call intel_fbc_deactivate() so that debugging
issues with FBC being delayed is clearer.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180125224122.27480-1-chris@chris-wilson.co.uk
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Add some newlines to intel_engine_dump() headers

The headers should be on a separate line for consistency, so add the
missing trailing newline in a few intel_engine_dump() callers.

Reported-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180205100618.11001-1-chris@chris-wilson.co.uk

drm/i915: Report if an unbannable context is involved in a GPU hang

Since unbannable contexts are special and supposed not to be causing GPU
hangs in the first place, make it clear when they are implicated in said
hang. In practice, most unbannable contexts are those created by igt
for the express purpose of throwing untold thousands of hangs at the GPU
and wish to keep doing so to finish the test. Normally they are cleaned
up, but it's when they or the other unbannable kernel contexts stay
stuck in an erroneous state that we need to worry and so need
highlighting.

Suggested-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180205094139.10671-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>

drm/i915: Remove spurious DRM_ERROR for cancelled interrupts

As we ourselves cancel interrupts during reset by clearing the GTIIR, it
is possible for the master IIR to indicate a pending IRQ for which we
have already cleared from the GTIIR. In this case, the DRM_ERROR are
intended and should not be flagged as an error.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180202153448.23908-1-chris@chris-wilson.co.uk

drm/i915/execlists: Flush GTIIR on clearing CS interrupts during reset

Be paranoid and flush the GTIIR after clearing the CS interrupt to be
sure it has taken before we re-enable the interrupt handler. We still
see early interrupts following reset, the tasklet handling the mmio read
before it has been written by the CS. This hopefully reduces the
frequency to 0...

References: https://bugs.freedesktop.org/show_bug.cgi?id=104262
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Acked-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180202145455.29876-1-chris@chris-wilson.co.uk

drm/i915: reduce indent in pch detection

Save some horizontal space.

Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180202130416.18233-1-jani.nikula@intel.com

drm/i915: Enable inject_load_failure only in DEBUG config

We're using i915_inject_load_failure() to inject dummy
faults during driver load, but since this is debug utility
we shouldn't expose it in default config as it consumes
both code and data.

add/remove: 0/1 grow/shrink: 0/2 up/down: 0/-302 (-302)
Function                                     old     new   delta
__i915_inject_load_failure                    61       -     -61
i915_gem_init                               1331    1268     -63
i915_driver_load                            5923    5745    -178
Total: Before=1177454, After=1177152, chg -0.03%

add/remove: 0/1 grow/shrink: 0/0 up/down: 0/-4 (-4)
Data                                         old     new   delta
i915_load_fail_count                           4       -      -4
Total: Before=56762, After=56758, chg -0.01%

add/remove: 4/8 grow/shrink: 0/1 up/down: 245/-591 (-346)
RO Data                                      old     new   delta
__param_str_inject_load_failure               20       -     -20
__UNIQUE_ID_inject_load_failuretype200        34       -     -34
__param_inject_load_failure                   40       -     -40
__func__                                    4998    4896    -102
__UNIQUE_ID_inject_load_failure201           150       -    -150
Total: Before=119095, After=118749, chg -0.29%

Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180201173248.3912-1-michal.wajdeczko@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915/dp: limit DP link rate based on VBT on CNL+

We have the max DP link rate info available in VBT since BDB version
216, included in child device config since commit c4fb60b9aba9
("drm/i915/bios: add DP max link rate to VBT child device
struct"). Parse it and use it.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/a8b1364d1f2394fba3062b6ad11b474744ea4366.1517482774.git.jani.nikula@intel.com

drm/i915/dp: clean up source rate limiting for cnl

Make the limiting rate based instead of messing with the array size.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/cb03b9419191a7d6359bf371aacb2d3725c746de.1517482774.git.jani.nikula@intel.com

drm/i915/dp: abstract rate array length limiting

This will be useful later on. Also move the functions around to not need
forward declarations in subsequent patches. No functional changes.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/40f37f08cad33234cd86337d39e823ac6e55805f.1517482774.git.jani.nikula@intel.com

drm/i915/bxt, glk: Avoid long atomic poll during CDCLK change

There is no requirement for doing the PCODE request polling atomically,
so do that only for a short time switching to sleeping poll afterwards.
The specification requires a 150usec timeout for the change notification,
so let's use that for the atomic poll. Do the extra 2ms poll - needed as
a workaround on BXT/GLK - in sleeping mode.

v2:
- rebase on v2 of patchset dropping the sandybridge_pcode_read/write
  refactoring (Chris)

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180130142939.17983-2-imre.deak@intel.com

drm/i915/bxt, glk: Increase PCODE timeouts during CDCLK freq changing

Currently we see sporadic timeouts during CDCLK changing both on BXT and
GLK as reported by the Bugzilla: ticket. It's easy to reproduce this by
changing the frequency in a tight loop after blanking the display. The
upper bound for the completion time is 800us based on my tests, so
increase it from the current 500us to 2ms; with that I couldn't trigger
the problem either on BXT or GLK.

Note that timeouts happened during both the change notification and the
voltage level setting PCODE request. (For the latter one BSpec doesn't
require us to wait for completion before further HW programming.)

This issue is similar to
commit 2c7d0602c815 ("drm/i915/gen9: Fix PCODE polling during CDCLK
change notification")
but there the PCODE request does complete (as shown by the mbox
busy flag), only the reply we get from PCODE indicates a failure.
So there we keep resending the request until a success reply, here we
just have to increase the timeout for the one PCODE request we send.

v2:
- s/snb_pcode_request/sandybridge_pcode_write_timeout/ (Ville)

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.4+
Acked-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103326
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180130142939.17983-1-imre.deak@intel.com

drm/i915/guc: Don't try to create log runtime if there is no log

In case of GuC initialization failure we may continue with driver
load, but we wrongly assume that GuC is fully functional. This
leads to the BUG as we attempt to access non-existing log vma.

[26386.121085] BUG: unable to handle kernel NULL pointer dereference at 00000000000000a0
[26386.121225] IP: guc_log_runtime_create+0x23/0xe0 [i915]
[26386.121763] Call Trace:
[26386.121870]  guc_log_late_setup+0xfd/0x140 [i915]
[26386.121969]  i915_driver_load+0x7ab/0x1730 [i915]
[26386.122069]  i915_pci_probe+0x2d/0x90 [i915]
[26386.122089]  pci_device_probe+0x9c/0x120
[26386.122107]  driver_probe_device+0x2a9/0x490
[26386.122126]  __driver_attach+0xd9/0xe0
[26386.122143]  ? driver_probe_device+0x490/0x490
[26386.122158]  bus_for_each_dev+0x57/0x90
[26386.122175]  bus_add_driver+0x1eb/0x260
[26386.122190]  ? 0xffffffffa069a000
[26386.122206]  driver_register+0x52/0xc0
[26386.122220]  ? 0xffffffffa069a000
[26386.122234]  do_one_initcall+0x39/0x170
[26386.122252]  ? kmem_cache_alloc_trace+0x1fd/0x2e0
[26386.122273]  do_init_module+0x56/0x1ec
[26386.122289]  load_module+0x219e/0x2550
[26386.122309]  ? vfs_read+0x121/0x140
[26386.122331]  ? SyS_finit_module+0xa5/0xe0
[26386.122346]  SyS_finit_module+0xa5/0xe0
[26386.122371]  entry_SYSCALL_64_fastpath+0x22/0x8f

Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180131173241.19704-4-michal.wajdeczko@intel.com
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915/guc: Don't forget to free GuC error log

We're freeing GuC error log in uc_fini_hw() that matches
corresponding uc_init_hw() but we missed the point that this
log object is copied on error path and in case of failure in
uc_init_hw() we will leak this object as uc_fini_hw() is
never called.

If we free this log object as part of the late uC cleanup, where
we also release other firmware objects, we can avoid this BUG:

[70841.001413] BUG drm_i915_gem_object (Tainted: G     U  W       ): Objects remaining in drm_i915_gem_object on __kmem_cache_shutdown()
[70841.001436] INFO: Slab 0x00000000c94e41af objects=21 used=1 fp=0x000000001d60c40a flags=0x8000000000008100

[70841.001466] Call Trace:
[70841.001471]  dump_stack+0x5e/0x8e
[70841.001476]  slab_err+0x99/0xb0
[70841.001483]  ? __slab_alloc.isra.24.constprop.29+0x62/0x70
[70841.001491]  ? __kmalloc+0x1f5/0x320
[70841.001497]  __kmem_cache_shutdown+0x18b/0x400
[70841.001505]  shutdown_cache+0x13/0x1c0
[70841.001511]  kmem_cache_destroy+0x1c2/0x240
[70841.001517]  ? __mutex_unlock_slowpath+0x38/0x270
[70841.001559]  i915_gem_load_cleanup+0xbc/0x130 [i915]
[70841.001595]  i915_driver_cleanup_early+0x11/0x60 [i915]
[70841.001630]  i915_driver_load+0x708/0x1720 [i915]
[70841.001638]  ? trace_hardirqs_on_caller+0xe2/0x1c0
[70841.001673]  i915_pci_probe+0x2d/0x90 [i915]
[70841.001680]  pci_device_probe+0x9c/0x120
[70841.001687]  driver_probe_device+0x2a9/0x490
[70841.001694]  __driver_attach+0xd9/0xe0
[70841.001700]  ? driver_probe_device+0x490/0x490
[70841.001705]  bus_for_each_dev+0x57/0x90
[70841.001712]  bus_add_driver+0x1eb/0x260
[70841.001717]  ? 0xffffffffa0685000
[70841.001723]  driver_register+0x52/0xc0
[70841.001728]  ? 0xffffffffa0685000
[70841.001733]  do_one_initcall+0x39/0x170
[70841.001739]  ? rcu_read_lock_sched_held+0x6f/0x80
[70841.001746]  ? kmem_cache_alloc_trace+0x27b/0x2e0
[70841.001753]  do_init_module+0x56/0x1ec
[70841.001759]  load_module+0x219e/0x2550
[70841.001766]  ? vfs_read+0x121/0x140
[70841.001774]  ? SyS_finit_module+0xa5/0xe0
[70841.001779]  SyS_finit_module+0xa5/0xe0
[70841.001788]  entry_SYSCALL_64_fastpath+0x22/0x8f

[70841.001806] INFO: Object 0x00000000eab7ed96 @offset=6208
[70841.001850] INFO: Allocated in i915_gem_object_create.part.32+0x1f/0x260 [i915] age=38 cpu=0 pid=2708
[70841.001861]  kmem_cache_alloc+0x23d/0x2d0
[70841.001897]  i915_gem_object_create.part.32+0x1f/0x260 [i915]
[70841.001937]  intel_guc_allocate_vma+0x15/0x100 [i915]
[70841.001977]  intel_guc_log_create+0x34/0x1c0 [i915]
[70841.002014]  intel_guc_init+0x5a/0x100 [i915]
[70841.002051]  intel_uc_init+0x3e/0xb0 [i915]
[70841.002089]  i915_gem_init+0x18e/0x540 [i915]
[70841.002123]  i915_driver_load+0xa7a/0x1720 [i915]
[70841.002159]  i915_pci_probe+0x2d/0x90 [i915]
[70841.002165]  pci_device_probe+0x9c/0x120
[70841.002171]  driver_probe_device+0x2a9/0x490
[70841.002177]  __driver_attach+0xd9/0xe0
[70841.002182]  bus_for_each_dev+0x57/0x90
[70841.002188]  bus_add_driver+0x1eb/0x260
[70841.002193]  driver_register+0x52/0xc0
[70841.002198]  do_one_initcall+0x39/0x170
[70841.002462] kmem_cache_destroy drm_i915_gem_object: Slab cache still has objects

[70841.002491] Call Trace:
[70841.002497]  dump_stack+0x5e/0x8e
[70841.002503]  kmem_cache_destroy+0x1e0/0x240
[70841.002509]  ? __mutex_unlock_slowpath+0x38/0x270
[70841.002551]  i915_gem_load_cleanup+0xbc/0x130 [i915]
[70841.002586]  i915_driver_cleanup_early+0x11/0x60 [i915]
[70841.002621]  i915_driver_load+0x708/0x1720 [i915]
[70841.002629]  ? trace_hardirqs_on_caller+0xe2/0x1c0
[70841.002664]  i915_pci_probe+0x2d/0x90 [i915]
[70841.002671]  pci_device_probe+0x9c/0x120
[70841.002678]  driver_probe_device+0x2a9/0x490
[70841.002684]  __driver_attach+0xd9/0xe0
[70841.002690]  ? driver_probe_device+0x490/0x490
[70841.002696]  bus_for_each_dev+0x57/0x90
[70841.002702]  bus_add_driver+0x1eb/0x260
[70841.002708]  ? 0xffffffffa0685000
[70841.002713]  driver_register+0x52/0xc0
[70841.002719]  ? 0xffffffffa0685000
[70841.002724]  do_one_initcall+0x39/0x170
[70841.002731]  ? rcu_read_lock_sched_held+0x6f/0x80
[70841.002737]  ? kmem_cache_alloc_trace+0x27b/0x2e0
[70841.002745]  do_init_module+0x56/0x1ec
[70841.002751]  load_module+0x219e/0x2550
[70841.002758]  ? vfs_read+0x121/0x140
[70841.002766]  ? SyS_finit_module+0xa5/0xe0
[70841.002772]  SyS_finit_module+0xa5/0xe0
[70841.002781]  entry_SYSCALL_64_fastpath+0x22/0x8f

Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180131173241.19704-2-michal.wajdeczko@intel.com
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915/selftests: add missing gtt shrinker test

Try to catch a bug we've seen in the wild where the shrinker purges the
pd/pdp from under us while allocating our paging structures.

References: https://bugs.freedesktop.org/show_bug.cgi?id=104773
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180131191453.12676-1-matthew.auld@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180131214440.7141-2-chris@chris-wilson.co.uk

drm/i915/ppgtt: Pin page directories before allocation

Commit e2b763caa6eb ("drm/i915: Remove bitmap tracking for used-pdpes")
believed that because it did not insert its freshly allocated page
directory into the pd tree, it was safe from the shrinker. I failed to
heed the lesson learnt from commit dd19674bacba ("drm/i915: Remove bitmap
tracking for used-ptes") that we need to pin all the levels in the tree
before hitting the shrinker or else the shrinker may free an upper layer
as we proceed to allocate the tree. Thus leaving dangling pointers
everywhere and a GPF should we hit direct reclaim at just the wrong
moment.

CPU: 0 PID: 7374 Comm: chromium Tainted: P           O    4.14.13-1-ARCH #1
Hardware name: Apple Inc. MacBookPro12,1/Mac-E43C1C25D4880AD6, BIOS MBP121.88Z.0167.B33.1706181928 06/18/2017
task: ffff994f696c2c40 task.stack: ffffb1a789d4c000
RIP: 0010:gen8_ppgtt_set_pde.isra.40+0x48/0x70 [i915]
RSP: 0018:ffffb1a789d4f940 EFLAGS: 00010206
RAX: 81c1788cc4f68138 RBX: ffff994f54db8000 RCX: ffff994f696c2c40
RDX: 000000023bc73003 RSI: ffff994d598b6b80 RDI: ffff994f54db8000
RBP: ffff994d598b6b80 R08: 0000000000000000 R09: 0000000000000000
R10: ffffb1a789d4f550 R11: ffff994eaf3c3208 R12: 0000000000000027
R13: 0000000000005000 R14: 0000000004e8f000 R15: ffff994f54dba000
FS:  00007f585886aa00(0000) GS:ffff994faec00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000004ac8e8 CR3: 00000002552c8004 CR4: 00000000003606f0
Call Trace:
 gen8_ppgtt_alloc_pdp+0x178/0x320 [i915]
 gen8_ppgtt_alloc_4lvl+0x5f/0x150 [i915]
 ppgtt_bind_vma+0x30/0x70 [i915]
 i915_vma_bind+0x68/0xd0 [i915]
 __i915_vma_do_pin+0x2d6/0x3a0 [i915]
 eb_lookup_vmas+0x7a2/0xb50 [i915]
 i915_gem_do_execbuffer+0x4d7/0x10e0 [i915]
 ? sock_wfree+0x34/0x60
 ? unix_stream_read_generic+0x1f9/0x7e0
 ? import_iovec+0x37/0xd0
 ? i915_gem_execbuffer2+0x5d/0x390 [i915]
 i915_gem_execbuffer2+0x1b7/0x390 [i915]
 ? i915_gem_execbuffer+0x2d0/0x2d0 [i915]
 drm_ioctl_kernel+0x59/0xb0 [drm]
 drm_ioctl+0x2d5/0x370 [drm]
 ? i915_gem_execbuffer+0x2d0/0x2d0 [i915]
 ? __seccomp_filter+0x3b/0x260
 do_vfs_ioctl+0xa1/0x610
 ? syscall_trace_enter+0xdb/0x2b0
 SyS_ioctl+0x74/0x80
 do_syscall_64+0x55/0x110
 entry_SYSCALL64_slow_path+0x25/0x25
RIP: 0033:0x7f584fa82d27
RSP: 002b:00007ffee14a7828 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 000003b0126a1030 RCX: 00007f584fa82d27
RDX: 00007ffee14a7870 RSI: 0000000040406469 RDI: 0000000000000080
RBP: 00007ffee14a7870 R08: 0000000000000002 R09: 0000000000000077
R10: 00007f5839f2b780 R11: 0000000000000246 R12: 0000000040406469
R13: 0000000000000080 R14: 00007f5842b00040 R15: 0000000000000000
Code: 01 00 83 81 58 0a 00 00 01 48 2b 05 13 9d fd c9 48 c1 f8 06 48 c1 e0 0c 48 8d 04 d0 48 8b 56 08 48 03 05 0c 9d fd c9 48 83 ca 03 <48> 89 10 83 a9 58 0a 00 00 01 65 ff 0d 37 03 fb 3e 74 02 f3 c3
RIP: gen8_ppgtt_set_pde.isra.40+0x48/0x70 [i915] RSP: ffffb1a789d4f940

Reported-by: Eric Blau <eblau@eblau.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104773
Fixes: e2b763caa6eb ("drm/i915: Remove bitmap tracking for used-pdpes")
References: dd19674bacba ("drm/i915: Remove bitmap tracking for used-ptes")
Testcase: igt/drv_selftest/live_gtt (igt_ppgtt_shrink_boom)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180131214440.7141-1-chris@chris-wilson.co.uk
Reviewed-by: Matthew Auld <matthew.auld@intel.com>

drm/i915/icl: allow the reg_read ioctl to read the RCS TIMESTAMP register

This enables the Mesa driver to advertise support for ARB_timer_query,
and thus an OpenGL version higher than 3.2.

Based on the CNL patch by Nanley Chery.

v2: Rebase.

Cc: Anuj Phogat <anuj.phogat@intel.com>
Cc: Nanley Chery <nanley.g.chery@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Requested-by: Anuj Phogat <anuj.phogat@intel.com>
Tested-by: Anuj Phogat <anuj.phogat@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180130134918.32283-10-paulo.r.zanoni@intel.com

drm/i915/icl: Set graphics mode register for gen11

This patch clears a single bit. The bit is 0 by default but expected
not to be set. Explicitly clearing the bit in this patch is intended
to indicate some thinking has occurred, and that we want this bit
cleared and we are not just excepting the default value.

We also stop setting GFX_RUN_LIST_ENABLE, which is correct since that
bit is gone.

v2 (from Paulo): fix indentation.
v3: Changed GEN check to >= 11. Corrected author name.
v4 (from Paulo): improve commit message (Daniele).

Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Kelvin Gardiner <kelvin.gardiner@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180130134918.32283-9-paulo.r.zanoni@intel.com

drm/i915/icl: Handle expanded PLANE_CTL_FORMAT field

ICL+ adds changes the PLANE_CTL_FORMAT field from [27:24] to [27:23],
however, all existing PLANE_CTL_FORMAT_* definitions still map to the
correct values.  Add an ICL_PLANE_CTL_FORMAT_MASK definition, and use
that for masking for the conversion to fourcc.

v2: No changes

v3: Change new definition name, drop comment (Rodrigo)

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180130134918.32283-8-paulo.r.zanoni@intel.com

drm/i915/gen11: fix the SAGV block time for gen11

It's 10us for gen 11.

Reviewed-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180130134918.32283-7-paulo.r.zanoni@intel.com

drm/i915/icl: Introduce MBus related registers

This patch introduce MBus control registers and their bit-fields
MBUS_ABOX_CTL
MBUS_BBOX_CTL
MBUS_DBOX_CTL
MBUS_UBOX_CTL

Changes Since V1:
 - Use function like macros (Paulo)
 - fix copy-paste error (Paulo)

Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180130134918.32283-6-paulo.r.zanoni@intel.com

drm/i915/icl: NV12 y-plane ddb is not in same plane

We don't have planar pixel format support implemented for ICL yet.
ICL require 2 display planes to be allocated for Planar formats unlike
previous GEN. So ICL/GEN11 doesn't require to write Y-plane ddb data in
NV12_BUF_CFG register and PLANE_NV12_BUF_CFG register is removed in ICL.

This patch removes the PLANE_NV12_BUF_CFG write for ICL.

Changes Since V1:
 - Improve commit message as per Paulo's comment

Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180130134918.32283-5-paulo.r.zanoni@intel.com

drm/i915/icl: Fail flip if ddb allocated are less than min display buffer needed

ICL require DDB allocation of plane to be more than "minimum display
buffer needed" for each level in order to enable WM level.

This patch implements and consider the same while allocating DDB
and enabling WM.

Changes Since V1:
 - rebase
Changes Since V2:
 - Remove extra parentheses
 - Use FP16.16 only when absolutely necessary (Paulo)
Changes Since V3:
 - Rebase
Changes since v4 (from Paulo):
 - Coding style issue.
Changes since v5 (from Paulo):
 - Do the final checks according to BSpec.

Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180130134918.32283-4-paulo.r.zanoni@intel.com

drm/i915/icl: Do not fix dbuf block size to 512

GEN9/10 had fixed DBuf block size of 512. Dbuf block size is not a
fixed number anymore in GEN11, it varies according to bits per pixel
and tiling. If 8bpp & Yf-tile surface, block size = 256 else block
size = 512

This patch addresses the same.

v2 (from Paulo):
  - Make it compile.
  - Fix a few coding style issues.
v3:
  - Rebase on top of upstream patches
v4 (from Paulo):
  - Bikeshed if statements (James).

Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180130134918.32283-3-paulo.r.zanoni@intel.com

drm/i915/icl: Don't allocate fixed bypass path blocks for ICL

GEN9 onwards bypass path allocation of 4 blocks was needed, as per
hardware design. ICL doesn't require bypass path allocation of 4 DDB
blocks, handling the same in this patch.

v2 (from Paulo):
  - No need for a comment that says what the code already says.

Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180130134918.32283-2-paulo.r.zanoni@intel.com

drm/i915: Flush ggtt writes through the old fenced vma before changing fences

This is a precautionary measure as I have no evidence to suggest we've
hit a bug here (I was hoping this might explain gdg's odd behaviour, but
alas), but given that we have a function to flush the ggtt writes it
seems prudent to use it prior to changing the fence register. Due to the
intrinsic nature of the GTT often operating as an independent mmio path,
we should not just rely on the write to the fence acting as a full flush
for GTT writes.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180130164457.14037-1-chris@chris-wilson.co.uk

drm/i915/guc: Fix return from guc_log_relay_file_create

guc_log_relay_file_create will return -EEXIST if we invoke
relay_late_setup_files multiple times as part of i915_guc_log_control.
However this is to be not cosidered as fail and need to return 0.
This was mistakenly introduced in the below commit. Fix it.

Fixes: 70deeaddc6e6 "drm/i915/guc: Fix lockdep due to log relay channel handling under struct_mutex"
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1517379279-12967-1-git-send-email-sagar.a.kamble@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915: Always run hangcheck while the GPU is busy

Previously, we relied on only running the hangcheck while somebody was
waiting on the GPU, in order to minimise the amount of time hangcheck
had to run. (If nobody was watching the GPU, nobody would notice if the
GPU wasn't responding -- eventually somebody would care and so kick
hangcheck into action.) However, this falls apart from around commit
4680816be336 ("drm/i915: Wait first for submission, before waiting for
request completion"), as not all waiters declare themselves to hangcheck
and so we could switch off hangcheck and miss GPU hangs even when
waiting under the struct_mutex.

If we enable hangcheck from the first request submission, and let it run
until the GPU is idle again, we forgo all the complexity involved with
only enabling around waiters. We just have to remember to be careful that
we do not declare a GPU hang when idly waiting for the next request to
be come ready, as we will run hangcheck continuously even when the
engines are stalled waiting for external events. This should be true
already as we should only be tracking requests submitted to hardware for
execution as an indicator that the engine is busy.

Fixes: 4680816be336 ("drm/i915: Wait first for submission, before waiting for request completion"
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104840
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180129144104.3921-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>

drm/i915/cnl: Fix DP max rate for Cannonlake with port F.

On CNL SKUs that uses port F,  max DP rate is 8.1G for all
ports when we have the elevated voltage (higher than 0.85V).

v2: Make commit message more generic.
v3: Move conditions to a helper to get easier to read. (Ville).
v4: Add a mention to the numerical voltage on commit
    message per Manasi request.
v5: Thanks CI! "error: control reaches end of non-void function"

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180129232223.766-10-rodrigo.vivi@intel.com

drm/i915/cnl: Enable DDI-F on Cannonlake.

Now let's finish the Port-F support by adding the
proper port F detection, irq and power well support.

v2: Rebase
v3: Use BIT_ULL
v4: Cover missed case on ddi init.
v5: Update commit message.
v6: Rebase on top of display headers rework.
v7: Squash power-well handling related to DDI F to this
    patch to avoid warns as pointed out by DK.
v8: Introduce DDI_F_LANES to PG2. (DK)
v9: Squash in the PORT_F case for enabling DP MST encoder. (DK)

Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180129232223.766-9-rodrigo.vivi@intel.com

drm/i915/cnl: Add HPD support for Port F.

On CNP boards that are using DDI F,
bit 25 (SDE_PORTE_HOTPLUG_SPT) is representing
the Digital Port F hotplug line when the Digital
Port F hotplug detect input is enabled.

v2: Reuse all existent structure instead of adding a
new HPD_PORT_F pointing to pin of port E.
v3: Use IS_CNL_WITH_PORT_F so we can start upstreaming
    this right now. If that SKU ever get a proper name
    we come back and update it.
v4: Rebase on top of digital connected port using encoder
    instead of port.
v5: Moved IS_CNL_WITH_PORT_F definition to the PCI IDs patch.

Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180129232223.766-8-rodrigo.vivi@intel.com

drm/i915: For HPD connected port use hpd_pin instead of port.

Let's try to simplify this mapping to hpd_pin -> bit
instead using port.
So for CNL with port F where we have this port using
hdp_pin and bits of other ports we don't need to duplicated
the mapping.

But for now this is only a re-org with no functional change
expected.

v2: Add missing lines and nuke @port reference from code
    documentation. (Ville)

Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180129232223.766-7-rodrigo.vivi@intel.com

drm/i915/cnl: Add right GMBUS pin number for HDMI on Port F.

On CNP Pin 3 is for misc of Port F usage depending on the
configuration. For CNL that uses Port F, pin 3 is the one.

v2: Make it more generic and update commit message.

Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180129232223.766-6-rodrigo.vivi@intel.com

drm/i915: Fix DPLCLKA_CFGCR0 bits for Port F.

Since when it got introduced with commit '555e38d27317
("drm/i915/cnl: DDI - PLL mapping")' the support for Port F
was wrong, because Port F bits are far from bits used
for A to E.

Since Port F is not used so far we don't need to propagate
Fixes back there.

v2: Reuse _SHIFT definition to avoid complicated duplication (DK).

Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180129232223.766-5-rodrigo.vivi@intel.com

drm/i915/cnl: Fix _CNL_PORT_TX_DW2_LN0_F definition.

This was wrong since its introduction on commit '04416108ccea
("drm/i915/cnl: Add registers related to voltage swing sequences.")'

But since no Port F was needed so far we don't need to
propagate fixes back there.

Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180129232223.766-4-rodrigo.vivi@intel.com

drm/i915/cnl: Extend Wa 1178 to Aux F.

We also need to extend this WA to Aux F.

Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180129232223.766-3-rodrigo.vivi@intel.com

drm/i915/cnl: Add AUX-F support

On some Cannonlake SKUs we have a dedicated Aux for port F,
that is only the full split between port A and port E.

There is still no Aux E for Port E, as in previous platforms,
because port_E still means shared lanes with port A.

v2: Rebase.
v3: Add couple missed PORT_F cases on intel_dp.
v4: Rebase and fix commit message.
v5: Squash Imre's "drm/i915: Add missing AUX_F power well string"
v6: Rebase on top of display headers rework.
v7: s/IS_CANNONLAKE/IS_CNL_WITH_PORT_F (DK)
v8: Fix Aux bits for Port F (DK)
v9: Fix VBT definition of Port F (DK).
v10: Squash power well addition to this patch to avoid
     warns as pointed by DK.
v11: Clean up squashed commit message. (David)
v12: Remove unnecessary handling for older platforms (DK)
     Adding AUX_F to PG2 following other existent ones. (DK)

Cc: David Weinehall <david.weinehall@linux.intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180129232223.766-2-rodrigo.vivi@intel.com

drm/i915/cnl: Add Cannonlake PCI IDs for another SKU.

The only difference is that this SKUs has the full
Port A/E split named as Port F.

But since SKUs differences don't matter on the platform
definition group and ids, let's merge all off them together.

v2: Really include the PCI IDs to the picidlist[];
v3: Add the PCI Id for another SKU (Anusha).
v4: Update IDs, really include to pciidlists again.
v5: Unify all GT2 IDs.
v6: Unify in a way that we don't break early-quirks.c
v7: Remove GT reference since it doesn't matter here (Paulo)
    Also move IS_CNL_WITH_PORT_F macro to this patch to
    make it easier for review this part and also to get
    used sooner.
v8: Rebased on top of commit 5db47e37b387 ("Revert "drm/i915:
mark all device info struct with __initconst"")

Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180129232223.766-1-rodrigo.vivi@intel.com

drm/i915: Add WA for planes ending close to left screen edge

While running the kms_plane clipping test I noticed a similar problem to
the one described in Display WA #1175. In this case, similarly for
planes other than the cursor, with 1 or 3 pixels visible from the left
edge of the screen to the end of the plane and an odd plane X offset
used for clipping causes the same kind of underflow and display
corruption as described for WA #1175. Fix this in a similar way as that
WA rejecting planes ending <4 pixels from the left screen edge.

v2:
- Rebase on v2 of patch 1/1.

Testcase: igt/kms_plane/plane-clipping-pipe-*-planes
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180116112415.22060-2-imre.deak@intel.com

drm/i915: Add display WA #1175 for planes ending close to right screen edge

As described in the WA on GLK and CNL planes on the right edge of the
screen that have less than 4 pixels visible from the beginning of the
plane to the edge of the screen can cause FIFO underflow and display
corruption.

On GLK/CNL I could trigger the problem only if the plane was at the same
time also aligned to the top edge of the screen (after clipping) and
there were exactly 2 pixels visible from the start of the plane to the
right edge of the screen (so couldn't trigger it with 1 or 3 pixels
visible). Nevertheless, to be sure, I also applied the WA for these cases.

I also couldn't see any problem with the cursor plane and later Art
confirmed that it's not affected, so the WA is applied only for the
other plane types.

v2:
- Use -ERANGE instead of -EINVAL. (Chris)

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180116112415.22060-1-imre.deak@intel.com

drm/i915/cnp: Properly handle VBT ddc pin out of bounds.

If the table result is out of bounds on the array map
there is something really wrong with VBT pin so we don't
return that vbt_pin, but only return 0 instead.

This basically reverts commit 'a8e6f3888b05 ("drm/i915/cnp:
Ignore VBT request for know invalid DDC pin.")'

Also this properly fixes commit 9c3b2689d01f ("drm/i915/cnl:
Map VBT DDC Pin to BSpec DDC Pin.")

v2: Do in a way that we don't break other platforms. (Jani)

v3: Keep debug message (Jani)

v4: Don't mess with 0 mapping was noticed by Jani and
    addressed with a simple solution suggested by Lucas
    that makes this even simpler.

Fixes: a8e6f3888b05 ("drm/i915/cnp: Ignore VBT request for know invalid DDC pin.")
Fixes: 9c3b2689d01f ("drm/i915/cnl: Map VBT DDC Pin to BSpec DDC Pin.")
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Kai Heng Feng <kai.heng.feng@canonical.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Suggested-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180125222524.22059-1-rodrigo.vivi@intel.com

drm/i915: Assert that we do not try to unsubmit a completed request

Assert that we do not try to unsubmit a completed request, as should we
try to resubmit it later, the ring is already past the request's
breadcrumb and the breadcrumb will not be updated.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180129094912.14428-1-chris@chris-wilson.co.uk
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>

drm/i915: Simplify guard logic for setup_scratch_page()

Older gcc is complaining it can't follow the guards and thinks that
addr may be used uninitialised

In the process, we can simplify down to one loop,
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-131 (-131)
Function                                     old     new   delta
setup_scratch_page                           545     414    -131

Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180129102840.19901-1-chris@chris-wilson.co.uk

Merge drm-next into drm-intel-next-queued

Pull 4.15 into drm-intel-next-queued for next feature pull.

Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

Revert "drm/i915: mark all device info struct with __initconst"

This reverts commit 5b54eddd3920e9f6f1a6d972454baf350cbae77e.

 Conflicts:
drivers/gpu/drm/i915/i915_pci.c

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104805
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Fixes: 5b54eddd3920 ("drm/i915: mark all device info struct with __initconst")
Link: https://patchwork.freedesktop.org/patch/msgid/20180129083346.29173-1-lionel.g.landwerlin@intel.com

drm/i915/lrc: Remove superfluous WARN_ON

Remove the WARN_ON(ce->state) inside the static function only called
when ce->state == NULL and downgrade the w/a batch setup warning into a
developer only mode (GEM_WARN_ON).

v2: Move the deferred alloc guard into the callee, eliminating the need
for the WARN_ON:
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-1 (-1)
Function                                     old     new   delta
execlists_context_pin                       1819    1818      -1

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180126121846.12007-1-chris@chris-wilson.co.uk

drm/i915/lrc: Clear context restore/save inhibit flags for new contexts

CTX_CONTEXT_CONTROL (CTX_SR_CTL) operates as a masked register and so
will only apply the bits that are selected by the upper half. In the
case of selectively enabling sr inhibit, this may mean the context keeps
the current setting (so forgetting to save the context later, eventually
leading to a very upset GPU!).

Fixes: 517aaffe0c1b ("drm/i915/execlists: Inhibit context save/restore for the fake preempt context")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180125112443.12745-1-chris@chris-wilson.co.uk
Reviewed-by: Michel Thierry <michel.thierry@intel.com>

Merge tag 'drm-misc-next-fixes-2018-01-18' of git://anongit.freedesktop.org/drm/drm-misc into drm-next

Fixes for 4.16:

Fixes one Kconfig issue and a enable some panels to work properly.
There is also a fix of error code return in sun4i.

* tag 'drm-misc-next-fixes-2018-01-18' of git://anongit.freedesktop.org/drm/drm-misc:
  drm: Fix PANEL_ORIENTATION_QUIRKS breaking the Kconfig DRM menuconfig
  drm/panel: lvds: Handle the optional regulator case properly
  drm/sun4i: Fix error code in sun4i_tcon_bind()

Merge branch 'drm-next-4.16' of git://people.freedesktop.org/~agd5f/linux into drm-next

 A few more fixes for 4.16, nothing major.

A few more fixes for 4.16.  This is on top of the pull request from
last week.  Most notable change here is a fix to the link order for
the now separate from amdgpu GPU scheduler to fix crashes when the
modules are build into the kernel rather than as modules.

* 'drm-next-4.16' of git://people.freedesktop.org/~agd5f/linux:
  drm: fix gpu scheduler link order
  drm/amd/display: Demote error print to debug print when ATOM impl missing
  drm/amdgpu: Avoid leaking PM domain on driver unbind (v2)
  drm/amd/amdgpu: Add Polaris version check
  drm/amdgpu: Reenable manual GPU reset from sysfs
  drm/amdgpu: disable MMHUB power gating on raven
  drm/ttm: Don't unreserve swapped BOs that were previously reserved
  drm/ttm: Don't add swapped BOs to swap-LRU list
  drm/amdgpu: only check for ECC on Vega10
  drm/amd/powerplay: Fix smu_table_entry.handle type
  drm/ttm: add VADDR_FLAG_UPDATED_COUNT to correctly update dma_page global count
  drm/radeon: fill in rb backend map on evergreen/ni.
  drm/amdgpu/gfx9: fix ngg enablement to clear gds reserved memory (v2)
  drm/ttm: only free pages rather than update global memory count together
  drm/amdgpu: fix CPU based VM updates
  drm/amdgpu: fix typo in amdgpu_vce_validate_bo
  drm/amdgpu: fix amdgpu_vm_pasid_fault_credit
  drm/ttm: check the return value of register_shrinker
  drm/radeon: fix sparse warning: Should it be static?

drm: fix gpu scheduler link order

It should initialize before the drivers using it.

Signed-off-by: Christian König <christian.koenig@amd.com>
Bug: https://bugs.freedesktop.org/show_bug.cgi?id=104736
Reviewed-by: Mike Lothian <mike@fireburn.co.uk>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Demote error print to debug print when ATOM impl missing

I assumed wrongfully that all relevant functions should be implemented.
Apparently this isn't the case. Demote the print to debug level for now.

Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/i915/guc: Fix comments style in intel_guc_log.c

Use consistent multi-line comment style as per guideline.

v2: Reverted comments prefix update to kernel-doc comment. (Chris)

Suggested-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1516808821-3638-5-git-send-email-sagar.a.kamble@intel.com

drm/i915/guc: Update name and prototype of i915_guc_log_control

i915_guc_log_control is GuC interface and GuC APIs that are not user
facing should be named with "intel_guc" prefix hence we change name to
intel_guc_log_control. Also changed the parameter to intel_guc struct.

v2: Move log vma check to intel_guc_log_control (Michal)
    Return -ENODEV when log isn't initialized. (Chris)

Suggested-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1516808821-3638-4-git-send-email-sagar.a.kamble@intel.com

drm/i915/guc: Fix lockdep due to log relay channel handling under struct_mutex

This patch fixes lockdep issue due to circular locking dependency of
struct_mutex, i_mutex_key, mmap_sem, relay_channels_mutex.
For GuC log relay channel we create debugfs file that requires i_mutex_key
lock and we are doing that under struct_mutex. So we introduced newer
dependency as:
    &dev->struct_mutex --> &sb->s_type->i_mutex_key#3 --> &mm->mmap_sem
However, there is dependency from mmap_sem to struct_mutex. Hence we
separate the relay create/destroy operation from under struct_mutex.
Also added runtime check of relay buffer status.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
======================================================
WARNING: possible circular locking dependency detected
4.15.0-rc6-CI-Patchwork_7614+ #1 Not tainted
------------------------------------------------------
debugfs_test/1388 is trying to acquire lock:
 (&dev->struct_mutex){+.+.}, at: [<00000000d5e1d915>] i915_mutex_lock_interruptible+0x47/0x130 [i915]

but task is already holding lock:
 (&mm->mmap_sem){++++}, at: [<0000000029a9c131>] __do_page_fault+0x106/0x560

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #3 (&mm->mmap_sem){++++}:
       _copy_to_user+0x1e/0x70
       filldir+0x8c/0xf0
       dcache_readdir+0xeb/0x160
       iterate_dir+0xdc/0x140
       SyS_getdents+0xa0/0x130
       entry_SYSCALL_64_fastpath+0x1c/0x89

-> #2 (&sb->s_type->i_mutex_key#3){++++}:
       start_creating+0x59/0x110
       __debugfs_create_file+0x2e/0xe0
       relay_create_buf_file+0x62/0x80
       relay_late_setup_files+0x84/0x250
       guc_log_late_setup+0x4f/0x110 [i915]
       i915_guc_log_register+0x32/0x40 [i915]
       i915_driver_load+0x7b6/0x1720 [i915]
       i915_pci_probe+0x2e/0x90 [i915]
       pci_device_probe+0x9c/0x120
       driver_probe_device+0x2a3/0x480
       __driver_attach+0xd9/0xe0
       bus_for_each_dev+0x57/0x90
       bus_add_driver+0x168/0x260
       driver_register+0x52/0xc0
       do_one_initcall+0x39/0x150
       do_init_module+0x56/0x1ef
       load_module+0x231c/0x2d70
       SyS_finit_module+0xa5/0xe0
       entry_SYSCALL_64_fastpath+0x1c/0x89

-> #1 (relay_channels_mutex){+.+.}:
       relay_open+0x12c/0x2b0
       intel_guc_log_runtime_create+0xab/0x230 [i915]
       intel_guc_init+0x81/0x120 [i915]
       intel_uc_init+0x29/0xa0 [i915]
       i915_gem_init+0x182/0x530 [i915]
       i915_driver_load+0xaa9/0x1720 [i915]
       i915_pci_probe+0x2e/0x90 [i915]
       pci_device_probe+0x9c/0x120
       driver_probe_device+0x2a3/0x480
       __driver_attach+0xd9/0xe0
       bus_for_each_dev+0x57/0x90
       bus_add_driver+0x168/0x260
       driver_register+0x52/0xc0
       do_one_initcall+0x39/0x150
       do_init_module+0x56/0x1ef
       load_module+0x231c/0x2d70
       SyS_finit_module+0xa5/0xe0
       entry_SYSCALL_64_fastpath+0x1c/0x89

-> #0 (&dev->struct_mutex){+.+.}:
       __mutex_lock+0x81/0x9b0
       i915_mutex_lock_interruptible+0x47/0x130 [i915]
       i915_gem_fault+0x201/0x790 [i915]
       __do_fault+0x15/0x70
       __handle_mm_fault+0x677/0xdc0
       handle_mm_fault+0x14f/0x2f0
       __do_page_fault+0x2d1/0x560
       page_fault+0x4c/0x60

other info that might help us debug this:

Chain exists of:
  &dev->struct_mutex --> &sb->s_type->i_mutex_key#3 --> &mm->mmap_sem

 Possible unsafe locking scenario:

       CPU0                    CPU1
       ----                    ----
  lock(&mm->mmap_sem);
                               lock(&sb->s_type->i_mutex_key#3);
                               lock(&mm->mmap_sem);
  lock(&dev->struct_mutex);

 *** DEADLOCK ***

1 lock held by debugfs_test/1388:
 #0:  (&mm->mmap_sem){++++}, at: [<0000000029a9c131>] __do_page_fault+0x106/0x560

stack backtrace:
CPU: 2 PID: 1388 Comm: debugfs_test Not tainted 4.15.0-rc6-CI-Patchwork_7614+ #1
Hardware name: To Be Filled By O.E.M. To Be Filled By O.E.M./J4205-ITX, BIOS P1.10 09/29/2016
Call Trace:
 dump_stack+0x5f/0x86
 print_circular_bug.isra.18+0x1d0/0x2c0
 __lock_acquire+0x14ae/0x1b60
 ? lock_acquire+0xaf/0x200
 lock_acquire+0xaf/0x200
 ? i915_mutex_lock_interruptible+0x47/0x130 [i915]
 __mutex_lock+0x81/0x9b0
 ? i915_mutex_lock_interruptible+0x47/0x130 [i915]
 ? i915_mutex_lock_interruptible+0x47/0x130 [i915]
 ? i915_mutex_lock_interruptible+0x47/0x130 [i915]
 i915_mutex_lock_interruptible+0x47/0x130 [i915]
 ? __pm_runtime_resume+0x4f/0x80
 i915_gem_fault+0x201/0x790 [i915]
 __do_fault+0x15/0x70
 ? _raw_spin_unlock+0x29/0x40
 __handle_mm_fault+0x677/0xdc0
 handle_mm_fault+0x14f/0x2f0
 __do_page_fault+0x2d1/0x560
 ? page_fault+0x36/0x60
 page_fault+0x4c/0x60

v2: Added lock protection to guc->log.runtime.relay_chan (Chris)
    Fixed locking inside guc_flush_logs uncovered by new lockdep.

v3: Locking guc_read_update_log_buffer entirely with relay_lock. (Chris)
    Prepared intel_guc_init_early. Moved relay_lock inside relay_create
    relay_destroy, relay_file_create, guc_read_update_log_buffer. (Michal)
    Removed struct_mutex lock around guc_log_flush and removed usage
    of guc_log_has_relay() from runtime_create path as it needs
    struct_mutex lock.

v4: Handle NULL relay sub buffer pointer earlier in read_update_log_buffer
    (Chris). Fixed comment suffix **/. (Michal)

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104693
Testcase: igt/debugfs_test/read_all_entries # with enable_guc=1 and guc_log_level=1
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Marta Lofstedt <marta.lofstedt@intel.com>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1516808821-3638-3-git-send-email-sagar.a.kamble@intel.com

drm/i915/guc: Enable interrupts before resuming GuC during runtime resume

GuC log streaming needs interrupts enabled prior to GuC resume but
runtime pm interrupt setup was happening post GuC resume. Fix it.
While at it, fix the unwinding of steps in the runtime suspend path.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104695
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Marta Lofstedt <marta.lofstedt@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1516808821-3638-2-git-send-email-sagar.a.kamble@intel.com

drm/i915/guc: Grab RPM wakelock while disabling GuC interrupts

Disabling GuC interrupts involves access to GuC IRQ control registers
hence ensure device is RPM awake.

v1-v2: old changelog
1: Add comment about need to synchronize flush work and log runtime
   destroy
2: Moved patch earlier in the series and removed comment about future
work. (Tvrtko)

v3: Added assert_rpm_wakelock_held() to gen9_*_guc_interrupts. (Chris)

Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1516808821-3638-1-git-send-email-sagar.a.kamble@intel.com

drm/i915: Add a comment exlaining CCS hsub/vsub

Let's document why we claim hsub==8,vsub==16 for CCS.

v2: Replace my explanation with Jason's

Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Cc: Daniel Stone <daniels@collabora.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180119144152.17224-1-ville.syrjala@linux.intel.com
Reviewed-by: Jason Ekstrand <jason@jlekstrand.net>

drm/i915: Implement display w/a #1143

Apparently SKL/KBL/CFL need some manual help to get the
programmed HDMI vswing to stick. Implement the relevant
workaround (display w/a #1143).

Note that the relevant chicken bits live in a transcoder register
even though the bits affect a specific DDI port rather than a
specific transcoder. Hence we must pick the correct transcoder
register instance based on the port rather than based on the
cpu_transcoder.

Also note that for completeness I included support for DDI A/E
in the code even though we never have HDMI on those ports.

v2: CFL needs the w/a as well (Rodrigo and Art)

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Art Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180122174131.28046-1-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

drm/i915: Use enum plane_id for frontbuffer tracking

Replace the ad-hoc plane indexing scheme used by the frontbuffer
tracking with enum plane_id.

The old video overlay not being part of the plane_id namespace
will just be given the high bit.

v2: Drop the unintended whitespace change (Chris)

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180123183343.9181-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915: Shrink the GEM kmem_caches upon idling

When we finally decide the gpu is idle, that is a good time to shrink
our kmem_caches.

v3: Defer until an rcu grace period after we idle.
v4: Think about epoch wraparound and how likely that is.
v5: Use I915_EPOCH_INVALID magic.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180124113608.14909-2-chris@chris-wilson.co.uk

drm/i915: Track the number of times we have woken the GPU up

By counting the number of times we have woken up, we have a very simple
means of defining an epoch, which will come in handy if we want to
perform deferred tasks at the end of an epoch (i.e. while we are going
to sleep) without imposing on the next activity cycle.

v2: No reason to specify precise number of bits here.
v3: Take Tvrtko's advice and reserve 0 as an invalid epoch.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180124113608.14909-1-chris@chris-wilson.co.uk

drm/i915/execlists: Inhibit context save/restore for the fake preempt context

We only use the preempt context to inject an idle point into execlists.
We never need to reference its logical state, so tell the GPU never to
load it or save it.

v2: BIT(2) for save-inhibit.

N.B. Daniele mentioned this bit mbz for ICL, and has been moved into the
submission process rather than the context image.

Suggested-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180123210412.17653-1-chris@chris-wilson.co.uk

drm/i915: Move LRC register offsets to a header file

Newer platforms may have subtle offset changes, which will increase the
number of defines, so it is probably better to start moving them to its
own header file. Also move the macros used while setting the reg state.

v2: Rename to intel_lrc_reg.h, to be consistent with i915_reg.h and
intel_guc_reg.h (Chris)
v3: License notice shenanigans.
v4: Documentation/process/coding-style.rst is always right (Chris)
v5: Rebase.

Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180124004349.22126-2-michel.thierry@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915/lrc: Update reg_state macros to pass checkpatch

The macros we use to init the reg_state had the following issues reported
by checkpatch --strict.

  Macro argument reuse 'reg_state' - possible side-effects
  Macro argument reuse 'pos' - possible side-effects
  Macro argument reuse 'ppgtt' - possible side-effects
  spaces preferred around that '+' (ctx:VxV)

So fix these issues before they are moved to a new header file.

Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180124004349.22126-1-michel.thierry@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915/pmu: Fix sysfs exported counter config

We need to generate the event config value using the uAPI class and not
the driver internal one.

Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: 109ec558370f ("drm/i915/pmu: Only enumerate available counters in sysfs")
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180123134558.3222-1-tvrtko.ursulin@linux.intel.com

drm/i915/cnl: Fix aux selection for WA 1178

Current code always select _CNL_AUX_ANAOVRD1_B
register regardless the pw in use.

CNL_DISP_PW_AUX_B = 9
CNL_DISP_PW_AUX_C = 10
CNL_DISP_PW_AUX_D = 11

And for pick we want

B = 0
C = 1
D = 2

Fixes: ddd39e4b3f8f ("drm/i915/cnl: apply Display WA #1178 to fix type C dongles")
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180123215245.24026-1-rodrigo.vivi@intel.com

drm/i915/cnp: Ignore VBT request for know invalid DDC pin.

Let's ignore VBT request if the pin is clearly wrong.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104139
Cc: Kai Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180123174050.4261-1-rodrigo.vivi@intel.com
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>

drm/amdgpu: Avoid leaking PM domain on driver unbind (v2)

We only support vga_switcheroo and runtime pm on PX/HG systems
so forcing runpm to 1 doesn't do anything useful anyway.

Only call vga_switcheroo_init_domain_pm_ops() for PX/HG so
that the cleanup path is correct as well.  This mirrors what
radeon does as well.

v2: rework the patch originally sent by Lukas (Alex)

Acked-by: Lukas Wunner <lukas@wunner.de>
Reported-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de> (v1)
Cc: stable@vger.kernel.org

drm/amd/amdgpu: Add Polaris version check

Add Polaris version check if firmware support UVD encode

Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: James Zhu <James.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

drm/amdgpu: Reenable manual GPU reset from sysfs

Otherwise it keeps rejecting the reset.

Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/i915/execlists: Skip forcewake for ELSP submission

Now that we can read the CSB from the HWSP, we may avoid having to
perform mmio reads entirely and so forgo the rigmarole of the forcewake
dance.

v2: Include forcewake hint for GEM_TRACE readback of mmio. If we don't
hold fw ourselves, the reads may return garbage.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180122100714.15137-1-chris@chris-wilson.co.uk

drm/i915: Increase render/media power gating hysteresis for gen9+

On gen9+, after an idle period the HW will disable the entire power well
to conserve power (by preventing current leakage). It takes around a 100
microseconds to bring the power well back online afterwards. With the
current hysteresis value of 25us (really 25 * 1280ns), we do not have
sufficient time to respond to an interrupt and schedule the next execution
before the HW powers itself down. (At present, we prevent this by
grabbing the forcewake for prolonged periods of time, but that overkill
fixed in the next patch.) The minimum we want to set the power gating
hysteresis to is the length of time it takes us to service the GPU, which
across a broad spectrum of machines is about 250us.

(Note this also brings guc latency into the same ballpark as execlists.)

v2: Include some notes on where I plucked the numbers from.

Testcase: igt/gem_exec_nop/sequential
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180122135541.32222-1-chris@chris-wilson.co.uk

drm/i915: Per-engine scratch VMA is mandatory

We fail engine initialization if the scratch VMA cannot be created so
there is no point in error handle it later. If the initialization ordering
gets messed up, we can explode during development just as well.

Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180119100005.9072-2-tvrtko.ursulin@linux.intel.com

drm/i915: Downgrade incorrect engine constructor usage warnings to development

Render engine constructor helpers must only be called from the render
engine constructors, but there is no need to burden the production
binaries with warnings which can only be triggered during development.

Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180119100005.9072-1-tvrtko.ursulin@linux.intel.com

drm/i915/edp: Do not do link training fallback or prune modes on EDP

In case of eDP because the panel has a fixed mode, the link rate
and lane count at which it is trained corresponds to the link BW
required to support the native resolution of the panel. In case of
panles with lower resolutions where fewer lanes are hooked up internally,
that number is reflected in the MAX_LANE_COUNT DPCD register of the panel.
So it is pointless to fallback to lower link rate/lane count in case
of link training failure on eDP connector since the lower link BW
will not support the native resolution of the panel and we cannot
prune the preferred mode on the eDP connector.

In case of Link training failure on the eDP panel, something is wrong
in the HW internally and hence driver errors out with a loud
and clear DRM_ERROR message.

v2:
* Fix the DEBUG_ERROR and add {} in else (Ville Syrjala)

Cc: Clinton Taylor <clinton.a.taylor@intel.com>
Cc: Jim Bride <jim.bride@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=103369
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1507835618-23051-1-git-send-email-manasi.d.navare@intel.com

drm/i915: Protect WC stash allocation against direct reclaim

As we attempt to allocate pages for use in a new WC stash, direct
reclaim may run underneath us and fill up the WC stash. We have to be
careful then not to overflow the pvec.

Fixes: 66df1014efba ("drm/i915: Keep a small stash of preallocated WC pages")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103109
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180121173143.17090-1-chris@chris-wilson.co.uk

drm/i915/psr: Don't name status or debug registers like control registers.

Avoids some typo pitfalls.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171220201021.17619-1-dhinakaran.pandiyan@intel.com

drm/amdgpu: disable MMHUB power gating on raven

MMHUB power gating still has issue, and doesn't work on raven at current. So
disable it for the moment.

Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

drm/i915: Shrink the request kmem_cache on allocation error

If we fail to allocate a new request, make sure we recover the pages
that are in the process of being freed by inserting an RCU barrier.

v2: Comment before the shrink and barrier in the error path.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180119144657.22606-1-chris@chris-wilson.co.uk

drm/i915/guc: Keep GuC log disabled by default

It looks that GuC log functionality is not fully functional yet and
causes issues when enabled by auto(-1) modparam on debug builds.
For example, but not limited to:

[   30.062893] ======================================================
[   30.062894] WARNING: possible circular locking dependency detected
[   30.062895] 4.15.0-rc8-CI-CI_DRM_3648+ #1 Tainted: G     U
[   30.062896] ------------------------------------------------------
[   30.062897] debugfs_test/1268 is trying to acquire lock:
[   30.062898]  (&dev->struct_mutex){+.+.}, at: [<00000000e4213449>] i915_mutex_lock_interruptible+0x47/0x130 [i915]
[   30.062921]
               but task is already holding lock:
[   30.062921]  (&mm->mmap_sem){++++}, at: [<00000000dd7adc93>] __do_page_fault+0x106/0x560
[   30.062924]
               which lock already depends on the new lock.

References: 0ed87953532652 ("drm/i915/guc: Redefine guc_log_level modparam values")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104693
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104694
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104695
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Saarinen <jani.saarinen@intel.com>
Cc: Tomi Sarvela <tomi.p.sarvela@intel.com>
Cc: Marta Lofstedt <marta.lofstedt@intel.com>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180119124926.29844-1-michal.wajdeczko@intel.com
Reviewed-by: Michal Winiarski <michal.winiarski@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915/icl: Gen11 render context size

Gen11 removes the Resource Streamer, which frees up a big chunk of
the context image. BSpec indicates 12544 DWORDs (13 pages), plus
one page for PPHWSP.

Please notice that, when looking at the BSpec context image table,
the right filter has to be applied as some rows are excluded for
specific GENs. Also, some rows apply per-subslice (for the
calculation above, we have supposed I915_MAX_SUBSLICES = 8).

v2: Rebase.
v3: Use the right size as per the BSpec.
v4:
  - Rebased on top of the default context size (Rodrigo)
  - Clarify in the commit message where the subslice calculation
    comes from.
v5: s/12538/12544/ (Daniele)

BSpec: 18907

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Ben Widawsky <benjamin.widawsky@intel.com> (older version)
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1515711307-28979-2-git-send-email-oscar.mateo@intel.com

drm/i915: Return a default RCS context size

Instead of returning whatever size the latest GEN used. This is because
context sizes for new GENs can go up or down, but the only safe thing to
do for missing cases is to use the largest known one, whatever that is.

Suggested-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1515711307-28979-1-git-send-email-oscar.mateo@intel.com

drm/i915/icl: Icelake interrupt register addresses and bits

MMIO addresses and register definition for the new interrupt
registers in Gen11.

v2: Removed spelt out VCS and VECS bit definitions. (Daniel Vetter)
v3: Adjust VCS and VECS. (Daniele Ceraolo Spurio)
v4: Bikeshedding (Paulo).

Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180109232336.11029-5-paulo.r.zanoni@intel.com

drm/i915/icp: Add the ID for ICL PCH - ICP

Add the PCI ID for the ICL PCH - ICP.

v2: rebased.
v3: rebased.
v4: fix ICP name.
v5: fix the ID mask (Fei Li).
v6 (from Paulo): bikesheds.

Cc: Li, Fei <fei.li@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180111180010.24357-9-paulo.r.zanoni@intel.com

drm/i915/icp: add ICP gmbus and gpio support

In ICP, there are three TC ports and 3 DDI ports.

v2:
 - Correct Pin mapping.
v3:
 - Update pin mapping into per platform implementation
   rather than previous approach of port wise mapping.
v4:
 - Update GMBUS_NUM_PINS (Paulo)
v5:
 - rebase.
v6:
 - Update function name, GMBUS_PIN_NUM (Paulo)
v7 (from Paulo):
 - Make it apply.
v8 (from Paulo):
 - Maintain consistent if ladder ordering.

Suggested by: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180111180010.24357-8-paulo.r.zanoni@intel.com

drm/i915/icp: Add backlight Support for ICP

ICP has two backlight controllers - similar to previous platforms like
BXT -, but we only use one controller for now, so we can just reuse
the CNP code.

v2: Remove the usage of ICP_SECOND_PPS_BACKLIGHT register.(Jani)
Reuse CNP code since it is very similar.(Ville)
v3 (from Paulo): Rebase.
v4 (from Paulo): adjust commit message (James) and comment (Rodrigo).

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: James Ausmus <james.ausmus@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180119184812.2888-1-paulo.r.zanoni@intel.com
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>

drm/i915/icp: Add Panel Power Sequencing Support

ICP, like BXT, has has two panel power sequencers.

v2: Simplify the code. Remove unwanted register definitions.
Make code as close to BXT style as possible. (Ville)
Also, remove the use of ICP_SECOND_PPS_BACKLIGHT for now.
Moving forward, if we are sure we need to set this register,
we can access it.

v3: Use INTEL_GEN(dev_priv), make code more readeable. (Ville)

v4 (from Paulo):
 - Coding style fixes.
 - Add a missing HAS_PCH_CNP -> gen10+ check.
 - Rebase.

v5: Use per platform checks rather than INTEL_GEN().
    v4 of this patch breaks on CoffeeLake, since CFL uses
    CNP and per platform check makes sense in that case.

v6 (from Paulo):
 - v5 was a patch on top of v4, not a new version. Now v6 is correctly
   a new version of the original patch.

Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180111180010.24357-6-paulo.r.zanoni@intel.com

drm/i915/icp: Get/set proper Raw clock frequency on ICP

Add register definitions for setting the rawclock.
Set the numerator,denominator and divider values.

v2: Simplify the commit message. Simplify the math.
Add  register bits for numerator. (Paulo)
v3 (from Paulo): coding style bikesheds.

Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180111180010.24357-5-paulo.r.zanoni@intel.com

drm/i915/icp: Introduce Ice Lake PCH

Add the enum additions to ICP PCH.

v2 (from Paulo): don't set any platforms to it yet since ICP support is
incomplete.
v3 (from Rodrigo): Fix ICP name.

Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180111180010.24357-4-paulo.r.zanoni@intel.com

drm/i915/icl: Add initial Icelake definitions.

Icelake is an Intel® Processor containing an Intel® Graphics
Controller.

This is just an initial Icelake definition. PCI IDs, Icelake support
and new features coming in following patches.

v2: Add .ddb_size and .has_guc (Michal Wajdeczko).
v3: Add the ICL_FEATURES macro (Kelvin Gardiner).
v4 (from Paulo): Add missing __initconst (Paulo) and say "graphics
controller" instead of something that looks like an official marketing
name but isn't (Chris).

Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180111180010.24357-3-paulo.r.zanoni@intel.com

drm/i915/cnl: Add Port F definition.

Some Cannonlake SKUs will come with a full split between
port A and port E. This will be called port F although it
is not a 6th port, but only a split.

Note this patch alone is not sufficient for port F enabling,
it's just the first step.

v2: Fix size of dvo_ports found by Ander.
v3: Adding missing cases from intel_bios.c for Port_F
v4: Adding other missing cases and fix the commit message.
v5: Rebase on top of display headers rework.
v6 (from Paulo): improve commit message, bikeshed bit definitions.

Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180111180010.24357-2-paulo.r.zanoni@intel.com

drm/i915: Check for fused or unused pipes

We may have fused or unused pipes in our system. Let's check that the pipe
in question is within limits of accessible pipes. In case, that we are not
able to access the pipe, we return early with a warning.

v2: Rephrasing of the commit message (Jani)

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103206
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Jaswinder Singh Rajput <jaswinder@perfectintelligent.com>
Suggested-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1513584243-12607-1-git-send-email-mika.kahola@intel.com

drm/i915: Allow up to 32KB stride on SKL+ "sprites"

SKL+ "sprites" no longer have 16KB max stride limit that earlier
platforms had. Bump up the limit to 32KB.

Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Cc: Daniel Stone <daniels@collabora.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171222192231.17981-7-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Add CCS capability for sprites

Allow sprites to scan out compressed framebuffers.

Since different platforms have a different set of planes that
support CCS let's add a small helper to determine whether a
specific plane supports CCS or not. Currently that information
is spread around in many places, and not all the pieces of
code even agree with each other.

In addition to allowing sprites to scan out compressed fbs,
the other fix here is that we stop rejecting them on pipe C
on CNL.

Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Cc: Daniel Stone <daniels@collabora.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171222192231.17981-6-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>

drm/i915: Clean up the sprite modifier checks

Split the g4x and snb cases into separate functions to match how we deal
with all other platforms. Also sort the switch cases to match the format
lists we've declared earlier, to ease comparisons.

Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Cc: Daniel Stone <daniels@collabora.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171222192231.17981-5-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>