David Bauer [Thu, 9 May 2019 16:04:06 +0000 (18:04 +0200)]
ramips: fix R6120 factory image
The factory firmware omits the JFFS2 end-marker while flashing via
web-interface. Add a 64k padding after the marker fixes this problem.
When the end-marker is not present, OpenWRT won't save the overlayfs
after initial flash.
Reported-by: Andreas Ziegler <dev@andreas-ziegler.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
Klaus Kudielka [Wed, 8 May 2019 18:40:51 +0000 (20:40 +0200)]
mvebu: fix board_name condition in 79_move_config
The correct board_name for the Turris Omnia is armada-385-turris-omnia.
Fixes: 4e8345ff68 ("mvebu: base-files: autodetect upgrade device")
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Klaus Kudielka [Wed, 8 May 2019 18:40:50 +0000 (20:40 +0200)]
base-files: improve lib/upgrade/common.sh
Recently, upgrade device autodetection has been added to the mvebu target.
This exposes some shortcomings of the generic export_bootdevice function,
e.g. on the Turris Omnia: export_bootdevice silently reports the root
partition to be the boot device. This makes the sysupgrade process fail at
several places.
Fix this by clearly distinguishing between /proc/cmdline arguments which
specify the boot disk, and those which specify the root partition. Only in
the latter case, strip off the partition, and do it consistently.
root=PARTUUID=<pseudo PARTUUID for MBR> (any partition) and root=/dev/*
(any partition) are accepted.
The root of the problem is that the *existing* export_bootdevice in
/lib/upgrade/common.sh behaves differently, if the kernel is booted with
root=/dev/..., or if it is booted with root=PARTUUID=...
In the former case, it reports back major/minor of the root partition,
in the latter case it reports back major/minor of the complete boot disk.
Targets, which boot with root=/dev/... *and* use export_bootdevice /
export_partdevice, have added workarounds to this behaviour, by specifying
*negative* increments to the export_partdevice function.
Consequently, those targets have to be adapted to use positive increments,
otherwise they are broken by the change to export_bootdevice.
Fixes: 4e8345ff68 ("mvebu: base-files: autodetect upgrade device")
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Tested-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Steve Glennon [Tue, 9 Apr 2019 20:46:32 +0000 (14:46 -0600)]
ipq40xx: add factory image for EnGenius ENS620EXT
Extended mksenaofw to support new "capwap" header structure.
This supports flashing from factory 3.0.0, 3.0.1, 3.1.0 and 3.5.5
firmware.
Note that the factory image format changes for 3.1 and later firmware,
and that the 3.1.0 and 3.5.5 Engenius firmware will refuse the
factory_30.bin file. Similarly, the 3.0.0 and 3.0.1 Engenius firmware
will refuse the factory_35.bin file.
Flashing from the Engenius 3.1.0 firmware with the factory_35.bin
firmware has not been tested, as 3.1.0 firmware (Engenius "middleFW")
is only intended as part of the upgrade path to 3.5.5 firmware.
Modified ipq40xx image Makefile to appropriately invoke mksenaofw
with new parameters to configure the capwap header.
Note that there is currently no method to return to factory firmware,
so this is a one-way street.
Path from factory 3.0.0 and 3.0.1 (EnGenius) software to OpenWrt is
to navigate to 192.168.1.1 on the stock firmware and navigate to the
firmware menu. Then copy the URL you have for that page, something like
http://192.168.1.1/cgi-bin/luci/;stok=
12345abcdef/admin/system/flashops
and replace the trailing /admin/system/flashops with just /easyflashops
You should then be presented with a simple "Firmware Upgrade" page.
On that page, BE SURE TO CLEAR the "Keep Settings:" checkbox.
Choose the openwrt-ipq40xx-engenius_ens620ext-squashfs-factory_30.bin,
click "Upgrade" and on the following page select "Proceed".
Path from factory 3.5.5 (EnGenius) software to OpenWrt is simply to
use the stock firmware update menu. Choose the
openwrt-ipq40xx-engenius_ens620ext-squashfs-factory_35.bin and click
"Upload" and "Proceed".
The device should then flash the OpenWrt firmware and reboot. Note
that this resets the device to a default configuration with Wi-Fi
disabled, LAN1/PoE acting as a WAN port (running DHCP client) and LAN2
acting as a LAN port with a DHCP server on 192.168.1.x (AP is at
192.168.1.1)
Signed-off-by: Steve Glennon <s.glennon@cablelabs.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[sorry, for unfixing the 80-lines eyesores.]
Steve Glennon [Tue, 23 Apr 2019 20:46:37 +0000 (14:46 -0600)]
ipq40xx: Fix reboot on EnGenius ENS620EXT
This patch works around an issue where reboot would cause the AP
to power down and not reboot.
The ipq4019 restart controller reboot causes the system
to power down and not recover. Fix is to disable the restart
controller in the device tree and the device reverts to
using the watchdog to perform the reset.
The real problem is due to the buggy bootloader that ships
with the device. Steve Glennon reported in the PR for this
patch: <https://github.com/openwrt/openwrt/pull/2009> that:
"the problem was due to a bad u-boot that ships with the device.
Using the u-boot that comes with 3.5.5.3 EnGenius factory
software now allows the old code (using the do_msm_reboot)
to reboot successfully.
On to the bad news:
Well 3.5.5.3 is a bad path. Finally managed to recover. You
CANNOT use prior EnGenius firmware to downgrade.
Findings:
* They now password protect the serial console with a new, unkown
password.
* They changed the protection on their walled-garden. I have to
use the ssh admin@ip /bin/sh --login to get out of their
walled-garden.
* Attempts to flash the original 3.0.0 or 3.0.1 EnGenius firmware
fail through the UI and sysupgrade. Their firmware update GUI now
seem to detect regular openwrt images, but they fail to flash
Attempts to flash a normal OpenWrt image with sysupgrade fail.
[..]
Attempts to sysupgrade with EnGenius firmware fail with the same
"mandatory section(s) missing" error, so you cannot downgrade to
3.0.0 or 3.0.1."
Signed-off-by: Steve Glennon <s.glennon@cablelabs.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [added valuable
findings from github discussion]
Alberto Bursi [Sat, 20 Apr 2019 15:25:29 +0000 (17:25 +0200)]
kirkwood: enable sata port multiplier
Marvell sata controllers in all kirkwood SoCs support
sata port multipliers, just like mvebu.
Enable this feature in the default kernel config
so it is available in normal builds.
tested and working on nsa310b
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Felix Fietkau [Sat, 27 Apr 2019 17:13:07 +0000 (19:13 +0200)]
build: add a config option for enabling a testing version of the target kernel
If the target supports a newer kernel version that is not used by default
yet, it can be enabled with this option
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Daniel Golle [Fri, 10 May 2019 23:25:12 +0000 (01:25 +0200)]
toolchain/nasm: update to version 2.14
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Deng Qingfang [Fri, 19 Apr 2019 10:04:56 +0000 (18:04 +0800)]
ramips: mt7620: fix dependencies
MT7620 integrated WMAC does not need RT2x00 PCI driver or firmware
Also corrected kmod-eeprom-93cx6 and kmod-lib-crc-itu-t dependencies
according to original Kconfig and lsmod output
This will remove some unnecessary packages from MT7620 target to
save some space
Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[75 characters per line in the commit message]
Hans Dedecker [Thu, 9 May 2019 16:31:01 +0000 (18:31 +0200)]
procd: fix compile issue
1361b97 container: include stdbool.h
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Hans Dedecker [Wed, 8 May 2019 19:52:20 +0000 (21:52 +0200)]
netifd: update to latest git HEAD
f6fb700 interface-ip: fine tune IPv6 mtu warning
975a5c4 interface: tidy ipv6 mtu warning
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Hans Dedecker [Wed, 8 May 2019 18:50:09 +0000 (20:50 +0200)]
procd: update to latest git HEAD
9b35439 procd: detect lxc container and behave accordingly
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Koen Vandeputte [Thu, 2 May 2019 12:31:34 +0000 (14:31 +0200)]
kernel: bump 4.19 to 4.19.38
Refreshed all patches.
Compile-tested on: cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Thu, 2 May 2019 12:30:50 +0000 (14:30 +0200)]
kernel: bump 4.14 to 4.14.115
Refreshed all patches.
Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Thu, 2 May 2019 12:25:32 +0000 (14:25 +0200)]
kernel: bump 4.9 to 4.9.172
Refreshed all patches.
Compile-tested on: ar7
Runtime-tested on: none
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Rosen Penev [Wed, 1 May 2019 17:05:20 +0000 (10:05 -0700)]
elfutils: Fix compile with uClibc-ng
Probably glibc too. argp_help takes a char *. not const char *.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[updated with upstream version of the patch]
Tomasz Maciej Nowak [Thu, 25 Apr 2019 13:38:16 +0000 (15:38 +0200)]
uboot-tegra: bump to 2019.04
This version has important change for tegra boards which is reserving
32MB memory for Linux kernel instead of current 16MB.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Jeff Kletsky [Fri, 3 May 2019 11:59:59 +0000 (04:59 -0700)]
ath79: glinet_gl-ar750s: Use QCA9887 firmware
The GL.iNet AR750S is based around the QCA9563
and requires the QCA9887 firmware for operation.
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Joachim Fünfer [Mon, 29 Apr 2019 10:53:08 +0000 (12:53 +0200)]
ar71xx: fix failsafe interface for TL-WR940nv6
Switches failsafe mode interface from WAN to LAN ports.
Tested on TL-WR940Nv6.0 and TL-WR940Nv6.1
Signed-off-by: Joachim Fünfer <joachim.fuenfer@stusta.net>
David Bauer [Mon, 22 Apr 2019 19:29:42 +0000 (21:29 +0200)]
ath79: fix OCEDO Raccoon 10Mbit PLL value
This corrects the PLL value for 10 Mbit/s links on the OCEDO Raccoon.
Prior to this patch, 10 Mbit/s links would not transmit data.
It is worth mentioning that the vendor firmware used the same PLL
settings and 10Mbit/s was also not working there.
All other link-modes are working correctly without any packet loss.
Signed-off-by: David Bauer <mail@david-bauer.net>
Arthur Skowronek [Wed, 30 Jan 2019 13:58:47 +0000 (14:58 +0100)]
base-files: add service_stopped as a post stop hook
Purpose of these changes is to introduce a hook for post service
shutdown in a similar fashion to the existing hook service_started. I
found it to be useful to specify a hook that is called once the service
has been stopped and not before the service is stopped like the
stop_service hook does.
The concrete use case I have for this is that I'm running a binary that
takes over the hardware watchdog timer. Said binary unfortunately can
not use ubus directly to tell procd to hand over the watchdog timer so
this has to be done in the service file for the binary in question. In
order to support a clean handover of the watchdog timer back to procd,
the service init script has to dispatch the ubus invocation once the
binary in question has been stopped.
Signed-off-by: Arthur Skowronek <ags@digineo.de>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[added commit message, use the same form as other hooks]
Rosy Song [Tue, 16 Apr 2019 01:05:14 +0000 (09:05 +0800)]
ar71xx: mute script error in ar922x-led-fix script
This commit fixes following script error in syslog:
cat: can't open '/sys/devices/platform/ehci-platform/usb1/1-1/1-1.2/1-1.2:1.4/ieee80211/phy*/name': No such file or directory
sh: add: unknown operand
sh: add: unknown operand
Signed-off-by: Rosy Song <rosysong@rosinson.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[commit subject and message tweaks]
Petr Štetiar [Wed, 10 Apr 2019 15:07:34 +0000 (17:07 +0200)]
kernel: Rename UPROBE_EVENT to UPROBE_EVENTS
Upstream has renamed UPROBE_EVENT to UPROBE_EVENTS in the following
commit:
commit
6b0b7551428e4caae1e2c023a529465a9a9ae2d4
Author: Anton Blanchard <anton@samba.org>
Date: Thu Feb 16 17:00:50 2017 +1100
perf/core: Rename CONFIG_[UK]PROBE_EVENT to CONFIG_[UK]PROBE_EVENTS
We have uses of CONFIG_UPROBE_EVENT and CONFIG_KPROBE_EVENT as
well as CONFIG_UPROBE_EVENTS and CONFIG_KPROBE_EVENTS.
Consistently use the plurals.
So I'm changing it to this plural option in order to make kconfig happy
and stop asking about it if kernel is compiled with verbose logging:
Enable uprobes-based dynamic events (UPROBE_EVENTS) [Y/n/?] (NEW)
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Wed, 10 Apr 2019 15:07:34 +0000 (17:07 +0200)]
config: kernel: Add KPROBE_EVENTS config option
Upstream has renamed KPROBE_EVENT to KPROBE_EVENTS in the following
commit:
commit
6b0b7551428e4caae1e2c023a529465a9a9ae2d4
Author: Anton Blanchard <anton@samba.org>
Date: Thu Feb 16 17:00:50 2017 +1100
perf/core: Rename CONFIG_[UK]PROBE_EVENT to CONFIG_[UK]PROBE_EVENTS
We have uses of CONFIG_UPROBE_EVENT and CONFIG_KPROBE_EVENT as
well as CONFIG_UPROBE_EVENTS and CONFIG_KPROBE_EVENTS.
Consistently use the plurals.
So I'm adding this plural option in order to make kconfig happy and stop
asking about it if kernel is compiled with verbose logging:
Enable kprobes-based dynamic events (KPROBE_EVENTS) [Y/n/?] (NEW)
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Hauke Mehrtens [Mon, 25 Mar 2019 14:29:06 +0000 (15:29 +0100)]
kernel: Remove support for kernel 3.18
No target is using kernel 3.18 anymore, remove all the generic
support for kernel 3.18.
The removed packages are depending on kernel 3.18 only and are not used on
any recent kernel.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Mon, 25 Mar 2019 14:15:57 +0000 (15:15 +0100)]
xburst: Remove unmaintained target
This target only supports kernel 3.18, which is not supported in OpenWrt
any more for multiple releases. It also looks like there is no active
maintainer for this target.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Mon, 25 Mar 2019 14:20:59 +0000 (15:20 +0100)]
omap24xx: Remove unmaintained target
This target only supports kernel 4.1, which is not supported in OpenWrt
any more for multiple releases. It also looks like there is no active
maintainer for this target.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Mon, 25 Mar 2019 14:19:15 +0000 (15:19 +0100)]
ppc44x: Remove unmaintained target
This target only supports kernel 3.18, which is not supported in OpenWrt
any more for multiple releases. It also looks like there is no active
maintainer for this target.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Mon, 25 Mar 2019 14:16:59 +0000 (15:16 +0100)]
ppc40x: Remove unmaintained target
This target only supports kernel 3.18, which is not supported in OpenWrt
any more for multiple releases. It also looks like there is no active
maintainer for this target.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Mon, 25 Mar 2019 14:18:26 +0000 (15:18 +0100)]
mcs814x: Remove unmaintained target
This target only supports kernel 3.18, which is not supported in OpenWrt
any more for multiple releases. It also looks like there is no active
maintainer for this target.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Mon, 25 Mar 2019 14:15:01 +0000 (15:15 +0100)]
au1000: Remove unmaintained target
This target only supports kernel 3.18, which is not supported in OpenWrt
any more for multiple releases. It also looks like there is no active
maintainer for this target.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Mon, 25 Mar 2019 14:17:43 +0000 (15:17 +0100)]
adm8668: Remove unmaintained target
This target only supports kernel 3.18, which is not supported in OpenWrt
any more for multiple releases. It also looks like there is no active
maintainer for this target.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Mon, 25 Mar 2019 14:10:39 +0000 (15:10 +0100)]
adm5120: Remove unmaintained target
This target only supports kernel 3.18, which is not supported in OpenWrt
any more for multiple releases. It also looks like there is no active
maintainer for this target.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Koen Vandeputte [Fri, 3 May 2019 14:13:19 +0000 (16:13 +0200)]
brcm2708: fix renamed definition (FS#2265)
This target adds an alternative mmc driver using a patch.
Within this patch, a definition got renamed upstream.
Change it to fix following compile error:
CC drivers/mmc/host/bcm2835-mmc.o
In file included from ./include/linux/kernel.h:14:0,
from ./include/linux/delay.h:22,
from drivers/mmc/host/bcm2835-mmc.c:25:
drivers/mmc/host/bcm2835-mmc.c: In function 'bcm2835_mmc_dumpregs':
drivers/mmc/host/bcm2835-mmc.c:254:27: error: 'SDHCI_ACMD12_ERR' undeclared (first use in this function); did you mean 'SDHCI_CMD_CRC'?
bcm2835_mmc_readw(host, SDHCI_ACMD12_ERR),
^
./include/linux/printk.h:137:18: note: in definition of macro 'no_printk'
printk(fmt, ##__VA_ARGS__); \
^~~~~~~~~~~
drivers/mmc/host/bcm2835-mmc.c:253:2: note: in expansion of macro 'pr_debug'
pr_debug(DRIVER_NAME ": AC12 err: 0x%08x | Slot int: 0x%08x\n",
^~~~~~~~
drivers/mmc/host/bcm2835-mmc.c:254:27: note: each undeclared identifier is reported only once for each function it appears in
bcm2835_mmc_readw(host, SDHCI_ACMD12_ERR),
^
./include/linux/printk.h:137:18: note: in definition of macro 'no_printk'
printk(fmt, ##__VA_ARGS__); \
^~~~~~~~~~~
drivers/mmc/host/bcm2835-mmc.c:253:2: note: in expansion of macro 'pr_debug'
pr_debug(DRIVER_NAME ": AC12 err: 0x%08x | Slot int: 0x%08x\n",
^~~~~~~~
scripts/Makefile.build:326: recipe for target 'drivers/mmc/host/bcm2835-mmc.o' failed
make[8]: *** [drivers/mmc/host/bcm2835-mmc.o] Error 1
Upstream commit:
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v4.14.114&id=
45fd8679ea86bffb352132a1df4917c3d11375aa
Fixes: b765f4be407c ("kernel: bump 4.14 to 4.14.114")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Rafał Miłecki [Wed, 1 May 2019 05:23:21 +0000 (07:23 +0200)]
procd: add procd_running() helper for checking running state
This should be helpful for implementing service_running() in procd init
scripts.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: John Crispin <john@phrozen.org>
Hans Dedecker [Thu, 2 May 2019 15:28:42 +0000 (17:28 +0200)]
procd: update to latest git HEAD
01f3dc8 instance: dump user and group as well
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Michael Heimpold [Thu, 11 Apr 2019 19:01:09 +0000 (21:01 +0200)]
procd: allow passing optional group instance parameter
Sometimes is desirable to run a process with a specific group id
instead of the default one which is derived from passwd entry.
This can be achived now by using procd_set_param group $mygroup.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_SOURCE_VERSION update]
Michael Heimpold [Thu, 11 Apr 2019 19:01:08 +0000 (21:01 +0200)]
procd: allow passing optional syslog facility as instance parameter
Optional syslog facility can be set by adding procd_set_param facility
$myfacility.
While at, also add stdout/stderr documentation.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_SOURCE_VERSION update]
Koen Vandeputte [Mon, 29 Apr 2019 11:02:18 +0000 (13:02 +0200)]
kernel: bump 4.19 to 4.19.37
Refreshed all patches.
Altered patches:
- 150-bridge_allow_receiption_on_disabled_port.patch
- 201-extra_optimization.patch
Compile-tested on: cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Mon, 29 Apr 2019 11:01:53 +0000 (13:01 +0200)]
kernel: bump 4.14 to 4.14.114
Refreshed all patches.
Altered patches:
- 150-bridge_allow_receiption_on_disabled_port.patch
- 201-extra_optimization.patch
Remove upstreamed:
- 022-0006-crypto-crypto4xx-properly-set-IV-after-de-and-encryp.patch
Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Mon, 29 Apr 2019 10:05:49 +0000 (12:05 +0200)]
kernel: bump 4.9 to 4.9.171
Refreshed all patches.
Altered patches:
- 150-bridge_allow_receiption_on_disabled_port.patch
- 201-extra_optimization.patch
Compile-tested on: ar7
Runtime-tested on: none
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Robert Marko [Tue, 30 Apr 2019 15:58:42 +0000 (17:58 +0200)]
kernel: iio: Fix BMP280 Auto probing
Currently Auto probing for BMP/BME280 does not work because kernel
module name in the call is not correct.
Package name was used instead of kernel module name.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Rafał Miłecki [Tue, 23 Apr 2019 07:39:14 +0000 (09:39 +0200)]
libroxml: bump to the 3.0.1 version
Some of changes:
* Support for local-name()
* General refactoring
* Better parsing performance
* Fix possible buffer overflow & memleak
* Validation checks
* More commit functions (file, buffer, fd)
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Hans Dedecker [Mon, 29 Apr 2019 19:32:12 +0000 (21:32 +0200)]
procd: update to latest git HEAD
cfaed56 procd: add SIGPWR as signal
a30a8fd procd: copy the respawn property of new instance
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Daniel Golle [Mon, 29 Apr 2019 16:21:34 +0000 (18:21 +0200)]
mac80211: rt2x00: replace patches with upstream version
Support for RT3883/RT3663 was merged upstream [1]. Use that patch
instead of our original series. The resulting source tree is
exactly identical, this commit is merely reorganizing the patches.
[1]: https://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next.git/commit/?id=
d0e61a0f7cca51ce340a5a73595189972122ff25
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hans Dedecker [Mon, 29 Apr 2019 12:56:04 +0000 (14:56 +0200)]
glibc: update to latest 2.27 commit (BZ #18035)
1961e5c7296 elf: Fix pldd (BZ#18035)
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Koen Vandeputte [Mon, 29 Apr 2019 13:28:03 +0000 (15:28 +0200)]
kernel: add missing symbol in 4.19 config
Intel AtomISP2 dummy / power-management driver (INTEL_ATOMISP2_PM) [N/m/y/?] (NEW)
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Deng Qingfang [Mon, 29 Apr 2019 05:26:36 +0000 (13:26 +0800)]
tools/ccache: update to 3.7
Update ccache to 3.7
Release notes:
https://ccache.dev/releasenotes.html#_ccache_3_7
Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
Felix Fietkau [Sat, 27 Apr 2019 16:56:30 +0000 (18:56 +0200)]
kernel: fix regression on 4.19 with 613-netfilter_optional_tcp_window_check.patch (FS#2253)
Since ct->proto.tcp.last_win isn't updated when nf_ct_tcp_no_window_check is
enabled, the retransmission timeout check needs to be bypassed.
Based on patch by Rob Mosher
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Eneas U de Queiroz [Thu, 25 Apr 2019 19:23:40 +0000 (19:23 +0000)]
openssl: build kmods only if engines are selected
Add a conditional to the individual package's for the kmods in DEPENDS.
This avoids the need to compile the kernel modules when the crypto
engine packages are not selected. The final binares are not affected by
this.
Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
Tested-by: Rosen Penev <rosenp@gmail.com>
Yousong Zhou [Fri, 26 Apr 2019 04:17:16 +0000 (04:17 +0000)]
scripts/qemustart: add notes on adding new options
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Yousong Zhou [Thu, 25 Apr 2019 14:05:24 +0000 (14:05 +0000)]
scripts/qemustart: fix network device emulation
We only enabled pcnet driver for malta machine, and x86/legacy target
was supposed to only support e1000 model
Cc: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Yousong Zhou [Thu, 25 Apr 2019 16:07:18 +0000 (16:07 +0000)]
scripts/qemustart: no network by default and enable with -n
This should make it easier to set up and possibly provide a "work out of
the box" experience for most test usage. Typical wan&lan networking
setup is only two characters argument away.
Cc: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Acked-by: Hans Dedecker <dedeckeh@gmail.com>
Yousong Zhou [Thu, 25 Apr 2019 05:26:23 +0000 (05:26 +0000)]
sdk: fix building external modules when CONFIG_STACK_VALIDATION=y
The option is at the moment enabled for x86/64. The selection chain
should be
config RETPOLINE
select STACK_VALIDATION if HAVE_STACK_VALIDATION
config x86
select HAVE_STACK_VALIDATION if X86_64
cryptdev-linux:
make[4]: Entering directory '/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/cryptodev-linux-cryptodev-linux-1.10'
make -C /store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/linux-4.14.113 M=/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/cryptodev-linux-cryptodev-linux-1.10 ARCH=x86 CROSS_COMPILE=x86_64-openwrt-linux-musl- modules
make[5]: Entering directory '/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/linux-4.14.113'
make[6]: *** No rule to make target '/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/cryptodev-linux-cryptodev-linux-1.10/ioctl.o', needed by '/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/cryptodev-linux-cryptodev-linux-1.10/cryptodev.o'. Stop.
Makefile:1533: recipe for target '_module_/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/cryptodev-linux-cryptodev-linux-1.10' failed
Open vSwitch intree kmods
make[7]: Entering directory '/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/openvswitch-2.11.0/datapath/linux'
make -C /store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/linux-4.14.111 ARCH=x86 M=/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/openvswitch-2.11.0/datapath/linux modules
make[8]: Entering directory '/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/linux-4.14.111'
make[9]: *** No rule to make target 'tools/objtool/objtool', needed by '/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/openvswitch-2.11.0/datapath/linux/actions.o'. Stop.
Makefile:1533: recipe for target '_module_/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/openvswitch-2.11.0/datapath/linux' failed
make[8]: *** [_module_/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/openvswitch-2.11.0/datapath/linux] Error 2
make[8]: Leaving directory '/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/linux-4.14.111'
Reference: builddeb: include objtool binary in headers package, https://patchwork.kernel.org/patch/
9014071/
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Jose Olivera [Wed, 24 Apr 2019 04:17:29 +0000 (12:17 +0800)]
elfutils: bump to 0.176
*Fixes:
-CVE-2019-7150
-CVE-2019-7149
-CVE-2019-7146
-CVE-2019-7665
-CVE-2019-7664
-CVE-2019-7148
*Refresh 003-libintl-compatibility.patch
*Also reset PKG_RELEASE.
Signed-off-by: Jose Olivera <oliverajeo@gmail.com>
Hans Dedecker [Wed, 24 Apr 2019 17:54:44 +0000 (19:54 +0200)]
scripts/qemustart: fix usage with networking support
Commit
8bf500eb79 added support for qemu usage without networking
support but broke networking support as -n and -z do not work with
unquoted argument; fix this by quoting the arguments.
Fixes
8bf500eb79
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Felix Fietkau [Wed, 24 Apr 2019 07:32:22 +0000 (09:32 +0200)]
mac80211: fix regression in skb resizing optimization in monitor mode (FS#2254)
struct ieee80211_local needs to be passed in separately instead of
dereferencing the (potentially NULL) sdata
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Koen Vandeputte [Fri, 12 Apr 2019 14:25:49 +0000 (16:25 +0200)]
toolchain/musl: update to version 1.1.22
new features:
- priority-inheritance mutexes
- membarrier syscall, pre-registration to use it, fallback emulation
- header-level support for new linux features in 4.19, 4.20, 5.0
major internal changes:
- complete, async-safe view of all existent threads as global list
- robust __synccall based on new thread list
- new dynamic TLS is installed synchronously at dlopen
- TLSDESC resolver functions no longer make bad ABI assumptions to call C
- resolved shared library dependencies are now recorded
compatibility & conformance:
- dependency-order shared library constructor execution
- sigaltstack no longer rejects SS_AUTODISARM, future flags
- FILE is now a complete (dummy) type in pre-C11 feature profiles
- setvbuf reports failure on invalid arguments
- TSVTX is exposed unconditionally in tar.h
- multithreaded set*id() no longer depends on /proc
- key slot reuse after pthread_key_delete no longer depends on /proc
bugs fixed:
- failures in multithreaded set*id() with concurrent thread creation/exit
- interposed free was called from invalid/inconsistent contexts
- freeaddrinfo performed invalid free of some partial results lists
- dlsym dependency order search had false negatives and false positives
- dn_skipname gave wrong results for labels with 8-bit content
- dcngettext clobbered errno, often breaking printing of error messages
- sscanf read past end of buffer under certain conditions (1.1.21 regression)
- pthread_key_create spuriously failed under race condition (1.1.21 regression)
- fdopendir wrongly succeeded with O_PATH file descriptors
- gets behaved incorrectly in presence of null bytes
- namespace violations in c11 tsd and mutex function dependencies
- incorrect prototype for makecontext (unimplemented)
arch-specfic bugs fixed:
- s390x had wrong values for POSIX_FADV_DONTNEED/_NOREUSE
Extensively tested on dozens of devices, covering most popular architectures.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Dainis Jonitis <dainis.jonitis@ubnt.com>
Signed-off-by: Roman Yeryomin <roman@advem.lv>
Koen Vandeputte [Fri, 12 Apr 2019 09:08:43 +0000 (11:08 +0200)]
ar71xx: add support for Mikrotik RouterBOARD 2011UiAS-2HnD r2
This board got a new hardware revision, without any change in functionality.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Tue, 16 Apr 2019 08:54:52 +0000 (10:54 +0200)]
ath10k-ct: Update to 2019-04-08
9cd701a4f028 ath10k-ct: Add PN get/set API for wave-2 firmware.
5c8a4668323b ath10k-ct: Support over-riding the power ctl table in eeprom
75e2705f31bb ath10k-ct: CCA, eeprom, other changes.
a696e602a0fc ath10k-ct: Attempt to fix-out-of-tree compile for 4.16
a2aec62262df ath10k: Improve beacon tx status for 4.20 kernel.
be5c21a82b15 ath10k-ct: Fix out-of-tree compile for 4.20, pull in stable changes for 4.19
Fixes compile errors when using the 4.20 flavour.
Also the amount of beacon errors seems to have dropped.
Tested on a Mikrotik RB912UAGS-5HPacD
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Mon, 22 Apr 2019 19:52:42 +0000 (21:52 +0200)]
kernel: bump 4.19 to 4.19.36
Refreshed all patches.
Compile-tested on: cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Mon, 22 Apr 2019 19:51:43 +0000 (21:51 +0200)]
kernel: bump 4.14 to 4.14.113
Refreshed all patches.
Compile-tested on: cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Mon, 22 Apr 2019 19:18:27 +0000 (21:18 +0200)]
kernel: bump 4.9 to 4.9.170
Refreshed all patches.
Compile-tested on: ar7
Runtime-tested on: none
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Jo-Philipp Wich [Tue, 23 Apr 2019 06:12:49 +0000 (08:12 +0200)]
Revert "uhttpd: disable concurrent requests by default"
This reverts commit
c6aa9ff38870a30dbe6da17e4edad6039fe10ddf.
Further testing has revealed that we will need to allow concurrent
requests after all, especially for situations where CGI processes
initiate further HTTP requests to the local host.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Eneas U de Queiroz [Mon, 22 Apr 2019 19:28:12 +0000 (19:28 +0000)]
openssl: add Eneas U de Queiroz as maintainer
Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
Koen Vandeputte [Thu, 18 Apr 2019 13:05:04 +0000 (15:05 +0200)]
kernel: bump 4.19 to 4.19.35
Refreshed all patches.
Fixes:
- CVE-2019-3887
New symbol:
- CONFIG_LDISC_AUTOLOAD
Compile-tested on: cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Thu, 18 Apr 2019 13:04:42 +0000 (15:04 +0200)]
kernel: bump 4.14 to 4.14.112
Refreshed all patches.
New symbol:
- CONFIG_LDISC_AUTOLOAD
Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Thu, 18 Apr 2019 08:04:35 +0000 (10:04 +0200)]
kernel: bump 4.9 to 4.9.169
Refreshed all patches.
New symbols:
- CONFIG_LDISC_AUTOLOAD
- CONFIG_PPC_BARRIER_NOSPEC
Compile-tested on: ar7
Runtime-tested on: none
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Eneas U de Queiroz [Mon, 22 Apr 2019 16:39:10 +0000 (16:39 +0000)]
openssl: fix OPENSSL_config bug affecting wget
This applies an upstream patch that fixes a OPENSSL_config() bug that
causes SSL initialization to fail when the openssl.cnf file is not
found. The config file is not installed by default.
Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
Hans Dedecker [Mon, 22 Apr 2019 11:39:35 +0000 (13:39 +0200)]
nghttp2: bump to 1.38.0
4a9d2005 Update manual pages
acf6a922 Bump up version number to 1.38.0, LT revision to 31:3:17
4ff45821 Update AUTHORS
42dce01e Merge branch 'nghttpx-fix-backend-selection-on-retry'
a35059e3 nghttpx: Fix bug that altered authority and path affect backend selection
5a30fafd Merge branch 'nghttpx-fix-chunked-request-stall'
dce91ad3 Merge branch 'nghttpx-dont-log-authorization'
2cff8b43 nghttpx: Fix bug that chunked request stalls
be96654d nghttpx: Don't log authorization request header field value with -LINFO
ce962c3f Merge branch 'update-http-parser'
f931504e Update http-parser to v2.9.1
d978f351 Fix bug that on_header callback is still called after stream is closed
ec519f22 Merge pull request #1270 from baitisj/master
e8b213e3 Bump up version number to 1.38.0-DEV
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Kevin Darbyshire-Bryant [Sun, 21 Apr 2019 13:57:44 +0000 (14:57 +0100)]
toolchain/binutils: refresh patches
Fix hunk offset warnings.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Hans Dedecker [Fri, 19 Apr 2019 17:21:27 +0000 (19:21 +0200)]
odhcpd: update to latest git HEAD (FS#2243, FS#2244)
6633efe router: fix dns search list option
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Rosy Song [Thu, 18 Apr 2019 02:20:19 +0000 (10:20 +0800)]
dropbear: allow build without dbclient
This can save ~16KBytes size for the ipk
Signed-off-by: Rosy Song <rosysong@rosinson.com>
Lucian Cristian [Thu, 18 Apr 2019 04:26:23 +0000 (07:26 +0300)]
armvirt64: enable qemu drm drivers
adds the qemu video drivers and also fixes the build failure
introduced with drm-kms-helper
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
Lucian Cristian [Thu, 18 Apr 2019 04:41:10 +0000 (07:41 +0300)]
kernel: add missing drm symbol
dependency introduced with module drm-kms-helper
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
Alexandru Ardelean [Wed, 17 Apr 2019 06:11:14 +0000 (09:11 +0300)]
include: unpack.mk: remove CRLF_WORKAROUND
This patch doesn't seem to have any more users.
The only one used to be target in
`target/linux/etrax/image/e100boot/Makefile`.
That target has since been removed via commit
1080f68b2b422f1e72e402765a45d0cc3c550825 .
There doesn't seem to be any reason left for this workaround.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Rafał Miłecki [Thu, 18 Apr 2019 08:13:13 +0000 (10:13 +0200)]
mac80211: brcm: backport brcmfmac 5.2 patches
This includes some USB fixes and early work on FullMAC firmware crash
recovery.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Petr Štetiar [Wed, 10 Apr 2019 08:10:33 +0000 (10:10 +0200)]
lantiq: tdw90x0: Fix WLAN LED on TP-Link W8970 v1.2 (FS#2232)
This patch fixes disfunctional WLAN LED on TP-Link W8970. The LED was
reported working in the CC release[1], but doesn't work anymore in 18.06.2.
1. https://github.com/openwrt/chaos_calmer/commit/
420cb24d41fcd650795f09d2b26e0e1d2cf21165
Tested-by: Damian Janarek <dzanar18@o2.pl>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Hans Dedecker [Wed, 17 Apr 2019 12:39:57 +0000 (14:39 +0200)]
odhcpd: update to latest git HEAD (FS#2206)
38bc630 router: use ra_lifetime as lifetime for RA options (FS#2206)
0523bdd router: improve code readibility
0a3b279 Revert "router:"
207f8e0 treewide: align syslog loglevels
f1d7da9 router:
0e048ac treewide: fix compiler warnings
83698f6 CMakeList.txt: enable extra compiler checks
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Eneas U de Queiroz [Tue, 16 Apr 2019 20:12:47 +0000 (20:12 +0000)]
openssl: change defaults: ENGINE:on, NPN:off, misc
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
Enable engine support by default. Right now, some packages require
this, so it is always enabled by the bots. Many packages will compile
differently when engine support is detected, needing engine symbols from
the libraries.
However, being off by default, a user compiling its own image will fail
to run some popular packages from the official repo.
Note that disabling engines did not work in 1.0.2, so this problem never
showed up before.
NPN support has been removed in major browsers & servers, and has become
a small bloat, so it does not make sense to leave it on by default.
Remove deprecated CONFIG_ENGINE_CRYPTO symbol that is no longer needed.
Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
Lucian Cristian [Sat, 13 Apr 2019 17:26:07 +0000 (20:26 +0300)]
kernel: Fix kmod-drm-amdgpu and kmod-drm-radeon dependencies
Currently the Geode builds fails on following kernel module missing
dependencies:
Package kmod-drm-amdgpu is missing dependencies for the following libraries:
backlight.ko
drm_kms_helper.ko
fb.ko
ttm.ko
So this patch tries to fix the kmod-drm-amdgpu module dependecies.
Fixes: 2f239c0 ("x86: video: add amdgpu DRM kernel package")
Fixes: 2f6918e ("x86: video: add radeon DRM module support")
Tested-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
Martin Schiller [Thu, 11 Apr 2019 07:54:37 +0000 (09:54 +0200)]
procd/hotplug: add dependency to dialout and audio group
Commit
6e060bd62c85 introduced a dependency to the dialout group.
Adding this group to the "group" file in the base-files package is not
enough to handle this dependency, because after a sysupgrade this entry
will be missing in the "group" file.
To address this problem the dependencies to the required groups needs to
be set in the Makefile of the procd package.
Then, the uci-default script "13_fix_group_user" will add the groups
on first boot-up after a sysupgrade.
Fixes: 6e060bd62c85 ("base-files/hotplug: fix dedicated group for tty devices")
Tested-by: Michael Heimpold <mhei@heimpold.de>
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Hans Dedecker [Mon, 15 Apr 2019 21:18:36 +0000 (23:18 +0200)]
netifd: update to latest git HEAD
666c14f system-linux: remove debug tracing
08989e4 interface: add neighbor config support
bfd4de3 interface: fix "if-down" hotplug event handling
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Christian Lamparter [Sun, 14 Apr 2019 20:34:52 +0000 (22:34 +0200)]
layerscape: unbreak ehci-fsl interaction with mpc85xx
Both targets have their own idea of how to use ehci-fsl.
This patch reverts part of commit
68b8d3b0796d ("kernel: usb: add FSL EHCI package") and moves
ehci-fsl back into kmod-usb2, while also making it hopefully
useable for the mpc85xx target.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Christian Lamparter [Sun, 14 Apr 2019 21:54:33 +0000 (23:54 +0200)]
mpc85xx: disable bricking TL-WDR4900v1 images
The current mpc85xx build is failing because the
TL-WDR4900v1 kernel image no longer fits into the
partition. Extending the kernel is not possible
without updating u-boot's kernel loader commands.
This patch disables the WDR4900v1 until the kernel
image size issue is fixed so the buildbot can still
compile the Sophos RED 15w Rev.1 . Installing the
WDR4900v1 images would cause the routers to get
bricked.
For the discussion, please go to:
<https://github.com/openwrt/openwrt/pull/1773>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Petr Štetiar [Thu, 11 Apr 2019 20:34:46 +0000 (22:34 +0200)]
kernel: MIPS: perf: ath79: Fix perfcount IRQ assignment
Currently it's not possible to use perf on ath79 due to genirq flags
mismatch happening on static virtual IRQ 13 which is used for
performance counters hardware IRQ 5.
On TP-Link Archer C7v5:
CPU0
2: 0 MIPS 2 ath9k
4: 318 MIPS 4
19000000.eth
7: 55034 MIPS 7 timer
8: 1236 MISC 3 ttyS0
12: 0 INTC 1 ehci_hcd:usb1
13: 0 gpio-ath79 2 keys
14: 0 gpio-ath79 5 keys
15: 31 AR724X PCI 1 ath10k_pci
$ perf top
genirq: Flags mismatch irq 13.
00014c83 (mips_perf_pmu) vs.
00002003 (keys)
On TP-Link Archer C7v4:
CPU0
4: 0 MIPS 4
19000000.eth
5: 7135 MIPS 5
1a000000.eth
7: 98379 MIPS 7 timer
8: 30 MISC 3 ttyS0
12: 90028 INTC 0 ath9k
13: 5520 INTC 1 ehci_hcd:usb1
14: 4623 INTC 2 ehci_hcd:usb2
15: 32844 AR724X PCI 1 ath10k_pci
16: 0 gpio-ath79 16 keys
23: 0 gpio-ath79 23 keys
$ perf top
genirq: Flags mismatch irq 13.
00014c80 (mips_perf_pmu) vs.
00000080 (ehci_hcd:usb1)
This problem is happening, because currently statically assigned virtual
IRQ 13 for performance counters is not claimed during the initialization
of MIPS PMU during the bootup, so the IRQ subsystem doesn't know, that
this interrupt isn't available for further use.
So this patch fixes the issue by simply booking hardware IRQ 5 for MIPS PMU.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Thu, 11 Apr 2019 20:06:45 +0000 (22:06 +0200)]
umbim: update to latest git HEAD
24f9dc7 Iron out all extra compiler warnings
9d8dbc9 Enable extra compiler checks
ff8d356 mbim-proxy support
ccca03f umbim: add registration set support
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Tue, 9 Apr 2019 12:24:11 +0000 (14:24 +0200)]
Revert "ath79: Add WPS button to TP-Link Archer C7v5"
Reverting this commit as I've missed the fact, that the button is
already present in the included DTSI file.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Mon, 8 Apr 2019 08:20:32 +0000 (10:20 +0200)]
mac80211: Fix rate_idx underflow in mwl8k (FS#2218)
Add a patch for mwl8k which fixes endless reboot loops on Linksys EA4500
with certain 5G configurations.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Eike Feldmann [Tue, 26 Feb 2019 22:04:53 +0000 (23:04 +0100)]
ramips: add support for Rakwireless RAK633
It's OEM module with 2*26 pin header, similar to LinkIt Smart 7688 or
Vocore2.
Specification:
CPU: MT7628 580 MHz. MIPS 24K
RAM: 64 MB
Flash: 8 MB
WIFI: 802.11n/g/b 20/40 MHz
USB: 1x Port USB 2.0
Ethernet: 5 Port ethernet switch
UART: 2x
Installation: Use the installed uboot Bootloader. Connect a serial cable
to serialport 0. Turn power on. Choose the option: "Load system code
then write to Flash via TFTP". Choose the local device IP and the TFTP
server IP and the file name of the system image. After if the
Bootloader will copy the image to the local flash.
Notes: The I2C Kernel module work not correctly. You can send and
receive data. But the command i2cdetect doesn’t work. FS#845
Signed-off-by: Eike Feldmann <eike.feldmann@outlook.com>
[commit subject and message touches, DTS whitespace fixes, wifi LED
rename, pinctrl fixes, network settings fixes, lan/wmac mac addresses,
removed i2c kernel modules]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
David Bauer [Fri, 12 Apr 2019 22:05:47 +0000 (00:05 +0200)]
ramips: add support for GL.iNet VIXMINI
Hardware
--------
SoC: MediaTek MT7628NN
RAM: 64M DDR2 (Etron EM68B16CWQD-25H)
FLASH: 8M (Winbond W25Q64JVSIQ)
LED: Power - WLAN
BTN: Reset
UART: 115200 8N1
TX and RX are labled on the board as pads next to the SoC
Installation via web-interface
------------------------------
1. Visit the web-interface at 192.168.8.1
Note: The ethernet port is by default WAN. So you need to connect to
the router via WiFi
2. Navigate to the Update tab on the left side.
3. Select "Local Update"
4. Upload the OpenWrt sysupgrade image.
Note: Make sure you select not to preserve the configuration.
Installation via U-Boot
-----------------------
1. Hold down the reset button while powering on the device.
Wait for the LED to flash 5 times.
2. Assign yourself a static IPv4 in 192.168.1.0/24
3. Upload the OpenWrt sysupgrade image at 192.168.1.1.
Signed-off-by: David Bauer <mail@david-bauer.net>
Pawel Dembicki [Tue, 29 Jan 2019 18:26:28 +0000 (18:26 +0000)]
mpc85xx: generic: Check kernel size for the TL-WDR4900
TP-Link TL-WDR 4900 have u-boot with read-only env.
Boot command read only 0x29F000 data from flash.
Bigger images causes crc error. It can't be changed.
This patch add kernel size checking.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [utilize KERNEL_SIZE]
David Bauer [Mon, 8 Apr 2019 18:09:35 +0000 (20:09 +0200)]
mpc85xx: clean up device package selection
Remove wireless and USB packages from the device-specific package
selection as they are already selected by the target itself.
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Mon, 8 Apr 2019 18:09:34 +0000 (20:09 +0200)]
mpc85xx: remove USB support from kernel
This removes USB support from the compiled kernel. Because of this, the
kernel is just small enough for the TP-Link WDR4900 to boot the
resulting kernel.
This is necessary to support the WDR4900 in the upcoming 19.xx release.
In the long run, this should be fixed with a second stage bootloader, as
the vendor bootloader only loads the first 2684k bytes.
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Mon, 8 Apr 2019 18:09:33 +0000 (20:09 +0200)]
kernel: usb: add FSL EHCI package
Add kernel module package for the Freescale USB2 EHCI used on the
mpc85xx platform.
Signed-off-by: David Bauer <mail@david-bauer.net>
INAGAKI Hiroshi [Sat, 13 Apr 2019 03:21:02 +0000 (12:21 +0900)]
ath79: remove unnecessary packages from I-O DATA ETG3-R
I-O DATA ETG3-R is a wired router. So wireless-related packages are
unnecessary and remove those packages from default configuration to
reduce flash usage.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Sven Roederer [Sun, 24 Mar 2019 23:03:19 +0000 (00:03 +0100)]
ath79: add TP-Link WR842N v3
This adds support for the TP-Link WR842N v3 which is already supported on ar71xx
target (
0b45bec22c59cc6e6b2fa71dc9a88386c5587132).
Specification:
* SoC: QCA9533 ver 2 rev 0
* 16 MB Flash (gd25q128)
* 64 MB RAM
* 1 WAN 10/100 MBit/s (blue connector)
* 4 LAN 10/100 MBit/s (AR8229; 4 ports; yellow connectors)
* Atheros AR9531 (2,4GHz, two fixed antennas)
* USB
* Reset / WPS button
* WiFi button (rf kill)
* 8 green leds; 1 red/green led
* serial console (115200 8N1, according to the OpenWrt-wiki some soldering is needed)
Installation:
* flash via vendor WebUI (the filename must not exceed certain length)
* sysupgrade from installed OpenWrt (also ar71xx)
Thanks to Holger Drefs for providing the hardware
Tested-by: @kofec (github)
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
Daniel Golle [Fri, 12 Apr 2019 20:07:29 +0000 (22:07 +0200)]
mac80211: rt2x00: replace patch with upstream version
Replace the patch introduced by commit
d0b969eee8 ("mac80211: rt2x00:
do not increment sequence number while re-transmitting") was merged
into wireless-drivers.git. Replace our version with the merged version.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Thu, 11 Apr 2019 20:26:28 +0000 (22:26 +0200)]
ramips: fix pinctrl to allow hardware i2c on WRTNODE2R
Instead of assigning I2C pins as GPIOs by default, leave it up to the
user whether to install kmod-i2c-mt7621 and use them for hardware I2C
instead.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Thu, 11 Apr 2019 17:19:49 +0000 (19:19 +0200)]
kernel: move and replace accepted patch
Signed-off-by: Daniel Golle <daniel@makrotopia.org>