ath10k: fix unregister deadlock when fw probe fails

If firmware probing worker failed it called
device_release_driver() which synchronously called
remove() pci callback. The callback in turn waited
for the worker that called it to finish resulting
in a deadlock.

Waiting for a completion instead of a worker, like
some other drivers do, doesn't seem like the best
idea either:

  Syscall                 Worker

                          probe_fw()
  rmmod
  dev_lock()
  pci->remove()
  wait_for_completion()
                          complete_all()
                          device_release_driver()
                          dev_lock()
                          [sleep]
  free(ar)
  dev_unlock()
                          [resume]

There's no guarantee that Worker upon resuming can
still access any data/code of the module.

Leaving device bound to a driver is not as harmful
as deadlocking so remove the call to
device_release_driver() while a proper solution is
figured out.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: add support for ar6004 hw3.0

This change enables ath6kl driver to support ar6004 hw3.0. At the same time do
some fixes in firmware initialisation which applies to ar6004 hw1.3 as well.

Signed-off-by: Jessica Wu <wjessica@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: add support wmi rate tables with mcs15

Some of the firmware versions support rate tables up to mcs15, add support for
that.

Signed-off-by: Jessica Wu <wjessica@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: don't set hi_refclk_hz if hardware version doesn't need it

Needed for ar6004 hw3.0 support.

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: implement rx flush for htc pipe

rx flush was not implemented for htc pipe, add that now. Doesn't fix any known
issues.

Also free the skb if htc control messages get canceled.

Signed-off-by: Jessica Wu <wjessica@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: convert ar6004 hardware flags to firmware feature flags

The functionality defined through these flags were actually firmware features
which can change between firmware versions. To make it possible to support
different firmware versions with the same driver, convert the flags to firmware
feature flags.

For backwards compatibility support for old ar6004 firmware FW
API 3 or smaller images we forcefully set the feature bits in the driver.
Starting from FW API 5 the firmware image needs to set them.

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: Fix ath6kl_bmi_read_hi32 macro

tmp may be used uninitialized if ath6kl_bmi_read() returns an error.

Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath10k: add implementation for configure max amsdu, ampdu

Allow to setup maximum subframes for AMSDU and AMPDU aggregation
via debugfs htt_max_amsdu_ampdu file.

Eg.
echo "2 64" > htt_max_amsdu_ampdu
will setup maximum amsdu subframes equal 2 and
maximum ampdu subframes equal to 64.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath10k: print Kconfig options

Print Kconfig options enabled/disabled in the build.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath10k: remove unused len variables from wmi process rx functions

These len variables are not used anywhere.

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

wil6210: improve debug for WMI receive

Print message if no events received. This should not happen.
If it is, it points to the problem in firmware.
Track also cases when multiple events processed in one IRQ

Print information as soon as possible - mbox pointers and
event header right after reading it. This helps to identify potential
problem with memory allocation for the event buffer.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-linville' of git://github.com/kvalo/ath

Merge tag 'nfc-next-3.16-2' of git://git./linux/kernel/git/sameo/nfc-next

Samuel Ortiz <sameo@linux.intel.com> says:

"NFC: 3.16: Second pull request

This is the 2nd NFC pull request for 3.16. We have:

- Felica (Type3) tags support for trf7970a
- Type 4b tags support for port100
- st21nfca DTS typo fix
- A few sparse warning check fixes"

Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192cu: remove check for CONFIG_AUTOSUSPEND

A check for CONFIG_AUTOSUSPEND was included in this driver when it was
added in v2.6.39. But that Kconfig symbol doesn't exist. Remove that
check and the single line it hides.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8723ae: Remove duplicate inclusion of fw_common.h

fw_common.h was included twice.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8723be: Remove duplicate inclusion of phy.h

phy.h was included twice.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix interface combinations for multi-channel concurrency

Currently mac80211 does not support WDS and DFS with channel context
drivers. So advertise these features only when the driver is not
supporting channel context and modparam "use_chanctx" is introduced
for preparing channel context support in ath9k.

Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: change hscfg gap parameter to avoid potential firmware deadlock

If host sleep parameter gap is set to 0xff, firmware will wait
for an ack from host to confirm the success of host wakeup.
This prevents firmware from uploading data packet before host
actually wakes up.

Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: set TDLS link for newly created RA list

Current implementation sets tdls_link flag only while restoring
packets from TDLS queue. If traffic to peer starts after TDLS is
setup, there is no way to set TDLS link flag to true. Do this
while creating RA list and we confirm that there exist a TDLS
peer for which setup is complete.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: fix a crash in extended scan event processing

[113.967694] Unable to handle kernel NULL pointer dereference
               at virtual address 00000020
............
[113.967859] PC is at mwifiex_update_rxreor_flags+0xfc/0x430
............
[113.968110] mwifiex_update_rxreor_flags+0xfc/0x430
[113.968129] mwifiex_handle_event_ext_scan_report+0x1e4/0x21c
[113.968148] mwifiex_process_sta_event+0x410/0x508
[113.968165] mwifiex_process_event+0x184/0x1e0
[113.968181] mwifiex_main_process+0x220/0x48c
[113.968197] mwifiex_sdio_interrupt+0xc8/0x1cc
[113.968210] sdio_irq_thread+0x11c/0x290

In case of legacy scan, adapter->curr_cmd is guranteed to be
non-NULL in check_next_scan_cmd. This may not be case in
extended scan where scan command response would come earlier and
set curr_cmd to NULL. Extended scan event comes later and while
trying to complete IOCTL for scan, driver would crash in
dereferencing adapter->curr_cmd->wait_q_enabled.

Avoid this by completing IOCTL in case of legacy scans only.
Internal scan would be completed while handling extended scan
command response.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: optimize radio switching on/off

Broadcom's wl 6.30.223.141 has some optimizations for radios 0x205[67].

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: optimize init by doing some ops just once

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: PHY: allow init optimizations by tracking PHY state

PHY has to be often re-initialized (e.g. during band switching after PHY
reset), however some operations have to be performed only once (only
power reset affects them).

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: optimize wil_release_reorder_frames

In case of receiving frame with sequence number far greater than current,
wil_release_reorder_frames() will iterate many times over empty buffer.

Optimize this case by checking buffer emptiness and simply update
head_seq_num without iterating.

Suggested-by: Vladimir Shulman <Vladimir.Shulman@Wilocity.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: improve pointers printing

use proper format %pad for the dma_addr_t arguments;
prefix %p with 0x, as %p don't print is by itself

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: detect scan timeouts

If scan has not finished in some reasonable time (10sec), interpret it as
if firmware error occurs but was not reported. Firmware should report
scan completion for every scan request, so it is error condition indeed.
Perform firmware recovery procedure.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: inline functions for vring hi/lo watermarks

Provide clear definition of the watermarks for the vring descriptor space.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: limit fw error recovery attempts

In case there is something fundamentally wrong with the firmware
(example: RF cable disconnected), FW will always crash immediately
after reset. This leads to infinite fw error recovery loop.

Count consecutive unsuccessful error recovery attempts in a short period
of time, and stop doing recovery after some reasonable count.
It is still possible to manually reset fw doing
interface down/up sequence.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: limit MTU

Obey 802.11 spec that defines max. data size 7920 bytes

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix deadlock while updating p2p beacon timer

pm_lock is taken twice while syncing HW TSF of p2p vif.
Fix this by taking the lock at caller side.

Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: remove firmware list from USB driver

The USB driver was using a list for firmware info that was
used in suspend/resume scenario. Now that brcmfmac is using
the asynchronous firmware request this is no longer needed.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: Remove interrupt endpoint usage from USB driver.

The USB bus driver always configured an USB intr EP urb. The
driver did not use the result at all and with newer firmware it is
causing continues errors on this EP.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: Increase max buffer size for receiving control message from dongle

The max buffer size for receiving control message from dongle needs to be
increased considering possible block padding. Otherwise some big control
message can't be received due to buffer overrun check.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Daniel Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmutil: assure unused bits are cleared in 11n chanspec

The firmware channel specification is a bitfield using a
16-bit integer, but only 14 lsb are used. Upon encoding
this value assure all 16 bits are cleared.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: make brcmf_fw_nvram_strip() static

The function brcmf_fw_nvram_strip() is no longer called so
it does not need to be exposed.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: use asynchronous firmware request in USB

This patch adds use of asynchronous firmware request to
the driver USB layer.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: use asynchronous firmware request in SDIO

This patch adds use of asynchronous firmware request to
the driver SDIO layer.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: introduce asynchronous firmware loading

The driver needs firmware to be loaded to the device, which
is done through the firmware class API. The synchronous call
request_firmware() need root filesystem to be mounted and/or
user-mode helper. These may not be avaliable on the moment
it is called. Instead use request_firmware_nowait().

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: Add log of superspeed device detection to USB probe.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: rework usb callback operations

The resume callbacks do partly the same a the probe callback
so put common code in separate function for use in the callbacks.
This also fixes suspend/resume regression introduced by

    brcmfmac: remove .init() callback for internal bus interface

    The .init() callback was the first function called by the common
    bus function brcmf_bus_start(). Given that it is not really
    necessary and the bus layer can call it before calling the
    brcmf_bus_start() function.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: call brcmf_detach() unconditional in sdio .remove() callback

The function brcmf_detach() checks whether it needs to do his stuff
or can return immediately. No need to have the same check in the
calling code.

Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: rename nvram.[ch] for upcoming firmware handling functions

The firmware processing will be modified to use asynchronous request
firmware api. In preparation this patch is simple rename of source
and header file to which the functionality will be added.

Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: remove .init() callback for internal bus interface

The .init() callback was the first function called by the common
bus function brcmf_bus_start(). Given that it is not really
necessary and the bus layer can call it before calling the
brcmf_bus_start() function.

Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: make chandef_to_chanspec() function static

The function chandef_to_chanspec() was added by

    brcmfmac: determine chanspec from struct cfg80211_chan_def info

    The struct cfg80211_chan_def contains additional info to derive the
    bandwidth and side-band information of the chanspec. This patch adds
    chandef_to_chanspec() function used in IBSS join and starting AP
    operation.

However, it introduced a sparse warning because the function
is only called from within the source file wl_cfg80211.c.

Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: restore mpc before passing scan status to cfg80211

Before informing cfg80211 about the scan status the device should
be put back in mpc state. If done after user-space may initiate
another (scheduled) scan and fail because scan is still busy as
shown in logging below:

[ 3301.367376] brcmfmac: brcmf_fweh_event_worker event ESCAN_RESULT (69)
[ 3301.377305] brcmfmac: brcmf_fweh_event_worker   version 2 flags 0 status 0
[ 3301.384993] brcmutil: event payload, len=12
[ 3301.389208] 00000000: 0c 00 00 00 6d 00 00 00 34 12 00 00
[ 3301.389214] brcmfmac: brcmf_sdio_kso_control Enter: on=0
[ 3301.402196] brcmfmac: brcmf_inform_bss scanned AP count (0)
[ 3301.407808] brcmfmac: brcmf_notify_escan_complete Enter
[ 3301.413064] brcmfmac: brcmf_notify_escan_complete ESCAN Completed scan: Done
[ 3301.420137] brcmfmac: brcmf_sdio_bus_txctl Enter
[ 3301.420368] brcmfmac: brcmf_cfg80211_sched_scan_start Enter
[ 3301.420370] brcmfmac: brcmf_cfg80211_sched_scan_start:
Scanning already: status (1)
[ 3301.440190] brcmfmac: brcmf_sdio_kso_control Enter: on=1
[ 3301.448695] brcmfmac: brcmf_sdio_tx_ctrlframe Enter
[ 3301.453662] brcmfmac: brcmf_sdio_bus_rxctl Enter
[ 3301.458326] brcmfmac: brcmf_sdio_isr Enter
[ 3301.462523] brcmfmac: brcmf_sdio_dpc Enter
[ 3301.466632] brcmfmac: brcmf_sdio_readframes Enter
[ 3301.471431] brcmfmac: brcmf_sdio_read_control Enter
[ 3301.476340] brcmfmac: brcmf_set_mpc MPC : 1

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: reduce log level for invalid scheduled scan request

When a regular scan does not return any networks user-space does
request a scheduled scan without any matchset or ssid. This can
not be handled by the firmware so we return -EINVAL. However, as
this request is done let us not add an error message to the log.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wcn36xx: Use kmemdup instead of kmalloc + memcpy

This issue was reported by coccicheck using the semantic patch
at scripts/coccinelle/api/memdup.cocci

Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: use time_after()

To be future-proof and for better readability the time comparisons are
modified to use time_after() instead of plain, error-prone math.

Signed-off-by: Manuel Schölling <manuel.schoelling@gmx.de>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

at76c50x-usb: Make WEP encryption working.

Currently the driver uses HW encryption.
Whenever mac80211 calls the set_key() callback the driver restarts the
whole HW configuration procedure, in order to set (also) the new
WEP key.
However, by doing this, it causes the card to loose association information,
and the HW becomes unable to communicate with the BSS.

This patch adds support for sending another HW command, that sets only
the wep key, instead of resetting all.
Mac80211 key-set requests are thus handled via this new command.

Tested on my at76c503

Signed-off-by: John W. Linville <linville@tuxdriver.com>

at76c50x-usb: Don't perform DMA from stack memory

Loading the driver with DMA debugging enabled makes the kernel to complain
about the ehci driver trying to perform DMA from memory from the stack.

[ 9848.229514] WARNING: CPU: 1 PID: 627 at lib/dma-debug.c:1153 check_for_stack+0xa4/0xf0()
[ 9848.237678] ehci-pci 0000:00:04.1: DMA-API: device driver maps memory fromstack [addr=ffff88006c80da01]

This is due to at76c50x-usb driver passing buffers allocated on the stack to
the USB layer, that attempts DMA. This occurs is several places.

This patch fixes the problem by allocating those buffers via kmalloc.

Since this adds some kfree() before leaving a couple of functions, I caught the
occasion to clean-up the exit path on error.

Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: avoid passing buffers to the hardware during flush

The commit "ath9k: fix possible hang on flush" changed the receive code
to always link rx descriptors of processed frames, even when flushing.
In some cases, this leads to flushed rx buffers being passed to the
hardware while rx is already stopped.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: simplify DFS pulse interval debug printing

Make DFS pulse interval calculation independent
from CONFIG_ATH9K_DEBUGFS.

Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rsi: avoid format string leak to thread name

Since the rsi_create_kthread interface does not include any format
string arguments, make sure that the resulting thread name can never
accidentally process the name as a format string.

Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-upstream' of git://git./linux/kernel/git/bluetooth/bluetooth-next

Conflicts:
drivers/bluetooth/btusb.c

Merge git://git./linux/kernel/git/jberg/mac80211-next

mac80211: set new interfaces as idle upon init

Mark new interfaces as idle to allow operations that require that
interfaces are idle to take place. Interface types that are always
not idle (like AP interfaces) will be set as not idle when they are
assigned a channel context.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Emmanuel Grumbach<emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: reduce packet loss notifications under load

During strong signal fluctuations under high throughput, few consecutive
failed A-MPDU transmissions can easily trigger packet loss notification,
and thus (in AP mode) client disconnection.

Reduce the number of false positives by checking the A-MPDU status flag
and treating a failed A-MPDU as a single packet.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: don't check netdev state for debugfs read/write

Doing so will lead to an oops for a p2p-dev interface, since it has
no netdev.

Cc: stable@vger.kernel.org
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wireless: add missing WLAN_EID_BSS_INTOLERANT_CHL_REPORT

Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: fix a memory leak on sta rate selection table

If the rate control algorithm uses a selection table, it
is leaked when the station is destroyed - fix that.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Christophe Prévotaux <cprevotaux@nltinc.com>
Fixes: 0d528d85c519 ("mac80211: improve the rate control API")
Cc: stable@vger.kernel.org # v3.10+
[add commit log entry, remove pointless NULL check]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless

regdb: Generalize the mW to dBm power conversion

Generalize the power conversion from mW to dBm
using log. This should fix the below compilation
error for country NO which adds a new power value
2000mW which is not handled earlier.

 CC [M]  net/wireless/wext-sme.o
 CC [M]  net/wireless/regdb.o
net/wireless/regdb.c:1130:1: error: Unknown undeclared here (not in
a function)
net/wireless/regdb.c:1130:9: error: expected } before power
make[2]: *** [net/wireless/regdb.o] Error 1
make[1]: *** [net/wireless] Error 2
make: *** [net] Error 2

Reported-By: John Walker <john@x109.net>
Signed-off-by: Chaitanya T K <chaitanya.mgit@gmail.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
[remove unneeded parentheses, fix rounding by using %.0f]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

ath10k: abort incomplete scatter-gather pci tx properly

This prevents leaving incomplete scatter-gather
transfer on CE rings which can lead firmware to
crash.

Reported-By: Avery Pennarun <apenwarr@gmail.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath10k: protect src_ring state with ce_lock in tx_sg()

It was possible to read invalid state of CE ring
buffer indexes. This could lead to scatter-gather
transfer failure in mid-way and crash firmware
later by leaving garbage data on the ring.

Reported-By: Avery Pennarun <apenwarr@gmail.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath10k: ensure rx-frag ignores rssi

It seems ath10k firmware gives us no way to know
the rssi for rx-fragments.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath10k: dont configure bssid for ap mode

FW creates self-peer for AP internally.

This prevents ath10k from trying to create
explicit self-peer during hw recovery and thus
prevents a timeout and a warning during teardown:

  ath10k: removing stale peer $AP_BSSID from vdev_id 0

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath10k: protect wep tx key setup

All configuration sequences should be protected
with conf_mutex to avoid concurrent/conflicting
requests.

This should make sure that wep tx key setup is not
performed while hw is restarted (at least).

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath10k: drain tx before restarting hw

This makes sure no further tx requests are
submitted to HTT before driver teardown.

This should prevent invalid pointer/NULL
dereference on htt tx pool in ath10k_htt_tx() in
some cases of heavy traffic.

kvalo: remove the WARN_ON() if conf_mutex is held

Reported-By: Ben Greear <greearb@candelatech.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath10k: perform hw restart lazily

This reduces risk of races and prepares for more
hw restart fixes.

It also makes sense to perform teardown after
mac80211 starts its restart routine as it
guarantees it has stopped itself by then
(including tx queues).

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath10k: clean up start() callback

This fixes failpath when override AC pdev param
setup fails and makes other pdev params setting
fail as well.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

mac80211: fix IBSS join by initializing last_scan_completed

Without this fix, freshly rebooted Linux creates a new IBSS
instead of joining an existing one. Only when jiffies counter
overflows after 5 minutes the IBSS can be successfully joined.

Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
[edit commit message slightly]
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: send events when devices are added/removed

We're currently sending NEW_WIPHY events for renames (which
is a bit odd, but now can't be changed), but also send them
for really new devices that register.

Also send DEL_WIPHY events when a device is removed, the
event ID for this was already reserved.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

ath10k: make core registering async

If ath10k was built into the kernel it could stall
booting for 120 seconds by default (60 seconds for
each firmware API variant) waiting for firmware
files before userspace was ready or filesystems
mounted.

Fix this by making the core registering
asynchronous.

This also shoves off about 1 second from boot time
on most systems since the driver is now mostly
initialized in a worker and modprobe takes very
little time to complete.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath10k: remove unnecessary tasklet_kill()

The tasklet is already guaranteed to be killed on
the teardown path.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath10k: relocate core create/destroy functions

This will avoid unnecessary forward declaration of
any kind in the future.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath10k: fix protected flag stripping

This prevents protected flag being stripped from
undecrypted raw sniffed frames when monitor
interface is active.

Reported-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Tested-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

mac80211: fix virtual monitor interface addition

Since the commit below, cfg80211_chandef_dfs_required()
will warn if it gets a an NL80211_IFTYPE_UNSPECIFIED iftype
as explicitely written in the commit log.
When an virtual monitor interface is added, its type is set
in ieee80211_sub_if_data.vif.type, but not in
ieee80211_sub_if_data.wdev.iftype which is passed to
cfg80211_chandef_dfs_required() hence resulting in the
following warning:

WARNING: CPU: 1 PID: 21265 at net/wireless/chan.c:376 cfg80211_chandef_dfs_required+0xbc/0x130 [cfg80211]()
Modules linked in: [...]
CPU: 1 PID: 21265 Comm: ifconfig Tainted: G        W  O 3.13.11+ #12
Hardware name: Dell Inc. Latitude E6410/0667CC, BIOS A01 03/05/2010
 0000000000000009 ffff88008f5fdb08 ffffffff817d4219 ffff88008f5fdb50
 ffff88008f5fdb40 ffffffff8106f57d 0000000000000000 0000000000000000
 ffff880081062fb8 ffff8800810604e0 0000000000000001 ffff88008f5fdba0
Call Trace:
 [<ffffffff817d4219>] dump_stack+0x4d/0x66
 [<ffffffff8106f57d>] warn_slowpath_common+0x7d/0xa0
 [<ffffffff8106f5ec>] warn_slowpath_fmt+0x4c/0x50
 [<ffffffffa04ea4ec>] cfg80211_chandef_dfs_required+0xbc/0x130 [cfg80211]
 [<ffffffffa06b1024>] ieee80211_vif_use_channel+0x94/0x500 [mac80211]
 [<ffffffffa0684e6b>] ieee80211_add_virtual_monitor+0x1ab/0x5c0 [mac80211]
 [<ffffffffa0686ae5>] ieee80211_do_open+0xe75/0x1580 [mac80211]
 [<ffffffffa0687259>] ieee80211_open+0x69/0x70 [mac80211]
[snip]

Fixes: 00ec75fc5a64 ("cfg80211: pass the actual iftype when calling cfg80211_chandef_dfs_required()")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Acked-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: add a single-transaction driver op to switch contexts

In some cases, when the driver is already using all the channel
contexts it can handle at once, we have to do an in-place switch
(ie. we cannot afford using an extra context temporarily for the
transaction).  But some drivers may not support switching the channel
context assigned to a vif on the fly (ie. without unassigning and
assigning it) while others may only work if the context is changed on
the fly, without unassigning it first.

To allow these different scenarios, add a new driver operation that
let's the driver decide how to handle an in-place switch.

Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

NFC: trf7970a: Add support for Felica Type 3 tags

Add support for the Felica protocol and Type 3 tags.
Both 212 and 424 kbps are supported.

Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: nfc_sock_link() can be static

CC: Hiren Tandel <hirent@marvell.com>
CC: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: digital: digital_in_send_attrib_req() can be static

CC: "Mark A. Greer" <mgreer@animalcreek.com>
CC: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: dts: st21nfca_i2c: Correct minor typo in documentation

Replaced st,st21nfca-i2c by st,st21nfca_i2c to be concistent
with below configuration and driver in drivers/nfc/st21nfca/

Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: digital: Randomize poll cycles

This change adds some entropy to polling cycles, choosing the next
polling rf technology randomly. This reflects the change done in the
pn533 driver, avoiding possible infinite loop for devices that export 2
targets on 2 different modulations. If the first target is not
readable, we will stay in an error loop for ever.

Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: digital: Return proper error code when sending ATR_REQ

The error code returned by digital_in_send_cmd() was not returned by
digital_in_send_atr_req().

Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC: port100: Add support for type 4B tag

This patch adds support for ISO-DEP protocol over NFC-B rf technology
by adding NFC_PROTO_ISO14443_B to the supported protocols and an entry
for framing configuration.

Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Bluetooth: Clearly distinguish mgmt LTK type from authenticated property

On the mgmt level we have a key type parameter which currently accepts
two possible values: 0x00 for unauthenticated and 0x01 for
authenticated. However, in the internal struct smp_ltk representation we
have an explicit "authenticated" boolean value.

To make this distinction clear, add defines for the possible mgmt values
and do conversion to and from the internal authenticated value.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

ath9k/ath10k: remove unnecessary channel_switch_beacon callbacks

The channel_switch_beacon callback is optional, so it doesn't have to
be defined if it's not going to do anything useful with it.  Both
ath9k and ath10k define the callback and just returns.  This commit
removes them.

Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath10k: fix ath10k_bmi_read32 macro

tmp may be used uninitialized if ath10k_bmi_read_memory() returns
an error.

Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath10k: prevent hif_stop being called twice

Recently there was a bug discovered that involved
hif_stop() being called twice that ended up with a
double free_irq() call but it only manifested with
multiple MSI interrupts mapping.

Catch this kind of a problem early in driver
regardless of interrupt mapping.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath10k: fix core start sequence

It was possible to call hif_stop() 2 times through
ath10k_htc_connect_init() timeout failpath which
could lead to double free_irq() kernel splat for
multiple MSI interrupt case.

Re-order init sequence to avoid this problem. The
HTC stop shouldn't stop HIF implicitly since it
doesn't implicitly start it. Since the re-ordering
required some functions to be split/removed/renamed
rename a few functions to make more sense while at
it.

Reported-By: Ben Greear <greearb@candelatech.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

mwifiex: use 'const' qualifier for 2nd arg of mwifiex_tdls_add_ht_oper

Fixes the following warning:

  CC      drivers/net/wireless/mwifiex/tdls.o
drivers/net/wireless/mwifiex/tdls.c: In function ‘mwifiex_prep_tdls_encap_data’:
drivers/net/wireless/mwifiex/tdls.c:475:4: warning: passing argument 2 of ‘mwifiex_tdls_add_ht_oper’ discards ‘const’ qualifier from pointer target type [enabled by
default]
    ret = mwifiex_tdls_add_ht_oper(priv, peer, 1, skb);
    ^
drivers/net/wireless/mwifiex/tdls.c:190:1: note: expected ‘u8 *’ but argument is of type ‘const u8 *’
 mwifiex_tdls_add_ht_oper(struct mwifiex_private *priv, u8 *mac,
 ^
drivers/net/wireless/mwifiex/tdls.c:481:4: warning: passing argument 2 of ‘mwifiex_tdls_add_ht_oper’ discards ‘const’ qualifier from pointer target type [enabled by
default]
    ret = mwifiex_tdls_add_ht_oper(priv, peer, 0, skb);
    ^
drivers/net/wireless/mwifiex/tdls.c:190:1: note: expected ‘u8 *’ but argument is of type ‘const u8 *’
 mwifiex_tdls_add_ht_oper(struct mwifiex_private *priv, u8 *mac,
 ^

Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix sleep timer during suspend

On idle state, sleep timer is scheduled to put the chip into fullsleep.
But during suspend, this timer is scheduled after the chip is moved to
fullsleep forcibily. This is causing below unnecessary error messages
in kernel log during suspend.

ath: phy2: timeout (100000 us) on reg 0x806c: 0xdeadbeef & 0x01f00000
!= 0x00000000
ath: phy2: RX failed to go idle in 10 ms RXSM=0xdeadbeef
ath: phy2: DMA failed to stop in 10 ms AR_CR=0xdeadbeef AR_DIAG_SW=0xdeadbeef
DMADBG_7=0xdeadbeef

Reported-by: Arkh4mKn1ght <arkh4mkn1ght@gmail.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Handle multiple keys while setting tx filters

The keycache index is used to abort transmission for given station
when it goes to sleep state. But the commit "ath9k_hw: Abort transmission
for sleeping station" is not handling multi-key station. Fix that.

Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: update seq number correctly for packets from TDLS peer

This patch adds handling of updating rx sequence number for
packets received from TDLS peer. Current implementation of
mwifiex_queueing_ra_based assumes station would always receive
packets from AP which is not true in case of TDLS.
Fix this by adding this case.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: set TDLS flags for AMSDU packets

This patch fixes an issue where AMSDU packets for TDLS link
would flow over infra link. This happened because we were
missing setting TDLS flag in TxPD on AMSDU packets.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: delete TDLS link upon Teardown event

If userspace application does not take care of TDLS teardown
event, TDLS link would be present in driver database and thus
driver would send such packets on direct link while peer has
already severed link causing data traffic failure. Disable TDLS
link upon teardown event so as to ensure this does not happen.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: silence TDLS link delete failure for nonexistent link

If TDLS link delete command fails because of non-existent peer
or TDLS peer is absent from driver's entry, it means link was
already deleted. In such case print debug messages with lower
severity.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: avoid TDLS check for packets destined to AP

In station role if TDLS is supported, we traverse TDLS peer list
to see if packet's destination address matches with TDLS peer.
Packets destined to AP are not sent over TDLS link and hence
avoid this list traversal for such packets.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix build error with disabled debug

DFS pulse interval printing is only available
when CONFIG_ATH9K_DEBUGFS is set.

Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: add missing calib values for radio 0x2026 rev 11

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>