Bjørn Mork [Tue, 6 Apr 2021 09:43:03 +0000 (11:43 +0200)]
uboot-envtools: add support for multiple config partitions
Most (all?) of the realtek devices have two u-boot config partitions
with a different set of variables in each. The U-Boot shell provides
two sets of apps to manipulate these:
printenv- print environment variables
printsys- printsys - print system information variables
saveenv - save environment variables to persistent storage
savesys - savesys - save system information variables to persistent storage
setenv - set environment variables
setsys - setsys - set system information variables
Add support for multiple ubootenv configuration types, allowing
more than one configuration file.
Section names are not suitable for naming the different
configurations since each file can be the result of multiple sections
in case of backup partitions.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Rafał Miłecki [Wed, 7 Apr 2021 12:38:45 +0000 (14:38 +0200)]
bcm4908: fix Netgear R8000P image
Use vendor format to allow flashing using Negear UI.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Wed, 7 Apr 2021 12:14:57 +0000 (14:14 +0200)]
bcm4908: add sysupgrade support
It supports flashing OpenWrt images (bootfs & UBI upgrade) as well as
vendor images (whole MTD partition write).
Upgrading cferom is unsupported. It requires copying device specific
data (like MAC) to target image before flashing.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Felix Fietkau [Wed, 7 Apr 2021 08:58:01 +0000 (10:58 +0200)]
mt76: update to the latest version
7d35b7a15d1d mt76: mt7915: add wifi subsystem reset
04122c89749d mt76: fix rx amsdu subframe processing
5e764ec9bece mt76: mt7921: introduce MT_WFDMA_DUMMY_CR definition
cf0badbc0497 mt76: mt7921: fix inappropriate WoW setup with the missing ARP informaiton
f32a4e15f5b2 mt76: mt7921: fix the dwell time control
54f52771a04a mt76: mt7921: fix kernel crash when the firmware fails to download
97189d2a045b mt76: mt7921: fix the insmod hangs
dcdbd7c89cf5 mt76: mt7921: fix MT_PCIE_MAC_INT_ENABLE access
813db729c02f mt76: mt7921: reduce the data latency during hw scan
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rafał Miłecki [Wed, 7 Apr 2021 07:30:30 +0000 (09:30 +0200)]
bcm4908: pad firmware image bootfs JFFS2 partition to 8 MiB
This way MTD "bootfs" partition will be always 8+ MiB. This should be
enough for any custom / future firmware to fit its bootfs (e.g. big
kernel) without having to repertition whole flash. That way we can
preserve UBI and its erase counters during sysupgrade.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Wed, 7 Apr 2021 05:59:57 +0000 (07:59 +0200)]
firmware-utils: bcm4908img: extract bootfs without padding
JFFS2 bootfs partition in a BCM4908 image usually includes some padding.
For flashing it individually (writing to designed MTD partition) we want
just JFFS2 data.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Tue, 6 Apr 2021 22:17:40 +0000 (00:17 +0200)]
firmware-utils: bcm4908img: fix extracting cferom
Fix offset to extract proper data when image contains vendor header.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Mon, 5 Apr 2021 17:30:06 +0000 (19:30 +0200)]
firmware-utils: bcm4908img: support extracting bootfs & rootfs
It's required for upgrading firmware using single partitions instead of
just blindly writing whole image.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Mon, 5 Apr 2021 23:06:52 +0000 (01:06 +0200)]
firmware-utils: bcm4908img: replace size with offset
It's much easier to operate on BCM4908 image data with absolute offset
of each section stored. It doesn't require summing sizes over and over.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Koen Vandeputte [Tue, 6 Apr 2021 10:16:10 +0000 (12:16 +0200)]
ath79: ar934x-nand: fix broken nand on kernel 5.10
Booting current 5.10.x testing kernel shows this:
[ 0.335781] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xf1
[ 0.342280] nand: Samsung NAND 128MiB 3,3V 8-bit
[ 0.346982] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048,
OOB size: 64
[ 0.354703] ar934x-nand
1b800200.nand: unknown ECC mode 2
[ 0.360193] ar934x-nand
1b800200.nand: nand_scan failed, err:-22
[ 0.366341] ar934x-nand: probe of
1b800200.nand failed with error -22
...
[ 1.089264] /dev/root: Can't open blockdev
[ 1.093482] VFS: Cannot open root device "(null)" or
unknown-block(0,0): error -6
[ 1.101077] Please append a correct "root=" boot option; here are the
available partitions:
[ 1.109555] 1f00 64 mtdblock0
[ 1.109559] (driver?)
[ 1.116199] 1f01 48 mtdblock1
[ 1.116202] (driver?)
[ 1.122841] 1f02 4 mtdblock2
[ 1.122844] (driver?)
[ 1.129493] 1f03 4 mtdblock3
[ 1.129497] (driver?)
[ 1.136138] 1f04 4 mtdblock4
[ 1.136142] (driver?)
[ 1.142787] Kernel panic - not syncing: VFS: Unable to mount root fs
on unknown-block(0,0)
[ 1.151168] Rebooting in 1 seconds..
The issue is caused by a wrong check for ECC engine type
on newer kernels.
Fix this.
Bootlog after:
[ 0.335689] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xf1
[ 0.342192] nand: Samsung NAND 128MiB 3,3V 8-bit
[ 0.346884] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048,
OOB size: 64
[ 0.354611] Scanning device for bad blocks
[ 0.364924] random: fast init done
[ 0.496641] 3 fixed-partitions partitions found on MTD device
ar934x-nand
[ 0.503545] Creating 3 MTD partitions on "ar934x-nand":
[ 0.508865] 0x000000000000-0x000000040000 : "booter"
[ 0.515133] 0x000000040000-0x000000400000 : "kernel"
[ 0.523265] 0x000000400000-0x000008000000 : "ubi"
Fixes: fb64e2c30f ("ath79: ar934x-nand: add kernel 5.10 compatibility")
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
Rafał Miłecki [Mon, 5 Apr 2021 22:03:31 +0000 (00:03 +0200)]
bcm4908: rename bootfs dummy file to the 1-openwrt
The purpose of that dummy file is to make CFE work properly with OpenWrt
bootfs. CFE for some reason ignores JFFS2 files with ino 0.
Rename it to 1-openwrt so:
1. It's consistent with bcm63xx
2. It's OpenWrt specific so sysupgrade can distinguish it from vendor
images
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Hans Dedecker [Mon, 5 Apr 2021 16:34:19 +0000 (18:34 +0200)]
glibc: update to latest git HEAD (BZ #27468, BZ #27511)
e78ea9bd26 Update Nios II libm-test-ulps.
98bb18f52a malloc: Fix a realloc crash with heap tagging [BZ 27468]
fc4ecce85b S390: Also check vector support in memmove ifunc-selector [BZ #27511]
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Daniel Golle [Mon, 5 Apr 2021 16:38:19 +0000 (17:38 +0100)]
uboot-mediatek: update to v2021.04
Remove patches merged upstream and refresh the remaining ones.
Runtime tested on
* Bananapi BPi-R64 (eMMC and SD Card)
* Linksys E8450 (SPI-NAND)
* Ubiquiti UniFi 6 LR (SPI-NOR)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Stijn Tintel [Mon, 5 Apr 2021 15:48:41 +0000 (18:48 +0300)]
lldpd: further size reductions
Size difference on mips_4kec:
Before: 120196
After: 120006
Closes https://github.com/openwrt/openwrt/pull/3823
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Suggested-by: Lucian Cristian <lucian.cristian@gmail.com>
Stijn Tintel [Mon, 5 Apr 2021 15:30:45 +0000 (18:30 +0300)]
lldpd: enable LTO
Size difference on mips_4kec:
W/o LTO: 139674
W/ LTO: 120196
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Suggested-by: Lucian Cristian <lucian.cristian@gmail.com>
Stijn Tintel [Mon, 5 Apr 2021 14:35:39 +0000 (17:35 +0300)]
lldpd: bump to 1.0.9
Contains fixes related to CVE-2020-27827.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Stijn Tintel [Thu, 11 Mar 2021 23:10:07 +0000 (01:10 +0200)]
lldpd: add libcap dependency
Now that libcap is in OpenWrt base, we can drop our custom patch to
disable libcap support and have lldpd depend on it instead. This will
allow the monitor process to drop its privileges instead of running as
root, improving security.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Stijn Tintel [Thu, 11 Mar 2021 23:08:25 +0000 (01:08 +0200)]
libcap: bump to 2.48
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Stijn Tintel [Thu, 11 Mar 2021 23:03:43 +0000 (01:03 +0200)]
libcap: drop invalid copyright header
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Stijn Tintel [Thu, 11 Mar 2021 23:03:22 +0000 (01:03 +0200)]
libcap: import from packages feed
Having libcap in OpenWrt base allows us to enable libcap support in
other packages in base.
In lldpd, this would allow the monitor process to drop its privileges
instead of running as root, improving security. It will also allow us to
drop our patch to disable libcap.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Rafał Miłecki [Mon, 5 Apr 2021 08:44:46 +0000 (10:44 +0200)]
bcm4908: enable JFFS2 support
It's needed for accessing JFFS2 bootfs partition.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Fri, 2 Apr 2021 15:28:21 +0000 (17:28 +0200)]
firmware-utils: bcm4908img: add bootfs support
This adds support for accessing bootfs JFFS2 partition in the BCM4908
image. Support includes:
1. Listing files
2. Renaming file (requires unchanged name length)
Above commands are useful for flashing BCM4908 images which by defualt
come with cferom.000 file and require renaming it.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Fri, 2 Apr 2021 14:31:43 +0000 (16:31 +0200)]
firmware-utils: bcm4908img: support extracting image data
It's useful for upgrading cferom, firmware, etc.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Fri, 2 Apr 2021 13:04:46 +0000 (15:04 +0200)]
firmware-utils: bcm4908img: find cferom size
It's important for modifying / extracting firmware content. cferom is
optional image content at the file beginning.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Fri, 2 Apr 2021 12:12:58 +0000 (14:12 +0200)]
firmware-utils: bcm4908img: use "info" command displaying file info
BCM4908 image format contains some info that may be useful for info /
debugging purposes.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Sun, 4 Apr 2021 12:53:00 +0000 (14:53 +0200)]
firmware-utils: bcm4908img: support reading from stdin
1. Don't allow pipe stdin as we need to fseek()
2. Don't alow TTY as it doesn't make sense for binary input
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Fri, 2 Apr 2021 11:59:02 +0000 (13:59 +0200)]
firmware-utils: bcm4908img: detect Netgear vendor firmware
Netgear uses CHK header which needs to be skipped when validating
BCM4908 image. Detect it directly in the bcm4908img tool. Dealing with
binary structs and endianess is way simpler in C.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Fri, 2 Apr 2021 11:02:51 +0000 (13:02 +0200)]
firmware-utils: bcm4908img: extract parsing code
Move code parsing existing firmware file to separated function. This
cleans up existing code and allows reusing parsing code for other
commands.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Robert Marko [Thu, 12 Nov 2020 18:45:22 +0000 (19:45 +0100)]
ipq40xx: add MikroTik hAP ac2 support
This adds support for the MikroTik RouterBOARD RBD52G-5HacD2HnD-TC
(hAP ac²), a indoor dual band, dual-radio 802.11ac
wireless AP with integrated omnidirectional antennae, USB port and five
10/100/1000 Mbps Ethernet ports.
See https://mikrotik.com/product/hap_ac2 for more info.
Specifications:
- SoC: Qualcomm Atheros IPQ4018
- RAM: 128 MB
- Storage: 16 MB NOR
- Wireless:
· Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 2.5 dBi antennae
· Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 2.5 dBi antennae
- Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 5x 1000/100/10 port,
passive PoE in
- 1x USB Type A port
Installation:
Boot the initramfs image via TFTP and then flash the sysupgrade
image using "sysupgrade -n"
Signed-off-by: Robert Marko <robimarko@gmail.com>
Daniel Golle [Fri, 2 Apr 2021 14:45:02 +0000 (15:45 +0100)]
uboot-mediatek: bpi-r64: no longer force recovery on first-boot
Now that sdcard.gz image contains everything needed to boot straight
into production image, no longer force booting into recovery image on
first boot by removing the logic which implemented that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Felix Fietkau [Sun, 4 Apr 2021 09:28:48 +0000 (11:28 +0200)]
mt76: update to the latest version
465dda65ee84 mt7615,mt7915: replace fw log 0-terminating code with wiphy info length limit
62b13f5352b8 mt76: mt7921: fix key set/delete issue
0ff3a336a8d8 mt7615,mt7915: fix a compiler warning
113ba8a81d54 mt76: mt7615: remove redundant dev_err call in mt7622_wmac_probe()
be1ab3b9ae7c mt76: mt7921: fix typo in mt7921_pci_resume
4e22f0dc934b mt76: mt7915: fix txpower init for TSSI off chips
e66a0b9b8d66 mt76: mt7615: always wake the device in mt7615_remove_interface
38f656768a90 mt76: mt7921: always wake the device in mt7921_remove_interface
6ee4770de083 mt76: mt7921: rework mt7921_mcu_debug_msg_event routine
e578b4b8d56a mt76: mt7615: fix .add_beacon_offload()
f8c6c7cbf10f mt76: mt7915: fix mt7915_mcu_add_beacon
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Kevin Darbyshire-Bryant [Tue, 30 Mar 2021 21:01:27 +0000 (22:01 +0100)]
kernel: bump 5.10 to 5.10.27
Use update_kernel to refresh all patches, required manual updates to:
610-netfilter_match_bypass_default_checks.patch
611-netfilter_match_bypass_default_table.patch
762-net-bridge-switchdev-Refactor-br_switchdev_fdb_notif.patch
764-net-bridge-switchdev-Send-FDB-notifications-for-host.patch
Run-tested: x86_64
Nothing screamed out but any funny business with linux bridging should
suspect this update first.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Hauke Mehrtens [Sat, 3 Apr 2021 17:11:38 +0000 (19:11 +0200)]
netifd: update to Git version 2021-04-03
f8899b9 netifd: bridge: set default value for igmp_snoop
327da98 netifd: add possibility to switch off route config
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 3 Apr 2021 17:04:53 +0000 (19:04 +0200)]
uclient: update to Git version 2021-04-03
83efca2 tests: fix possibly longer start of HTTP server
64e00d6 uclient-fetch: document missing options
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rui Salvaterra [Wed, 25 Nov 2020 23:03:48 +0000 (23:03 +0000)]
hostapd: enable airtime policy for the -basic variants
Airtime policy configuration is extremely useful in multiple BSS scenarios.
Since nowadays most people configure both private and guest networks (at
least), it makes sense to enable it by default, except for the most limited
of the variants.
Size of the hostapd-basic-openssl binary (mipsel 24Kc -O2):
543944 bytes (airtime policy disabled)
548040 bytes (airtime policy enabled)
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Stijn Segers [Sun, 28 Feb 2021 21:50:15 +0000 (22:50 +0100)]
realtek: rename partitions in Netgear DTSI
Switch the Netgear DTSI for the Realtek target from the OEM partition
naming scheme to accepted OpenWrt naming practices. A quick git grep for
'u-boot-env' e.g. in the OpenWrt tree turns up almost 500 hits whereas
grepping for 'bdinfo' (the OEM equivalent) returns a meagre 14.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Rui Salvaterra [Thu, 1 Apr 2021 13:36:33 +0000 (14:36 +0100)]
zram-swap: bail out early if the kernel doesn't support swap
Since KERNEL_SWAP is only enabled by default for !SMALL_FLASH targets, we need
to check if the current kernel supports swap before trying to configure
zram-swap, as opkg can't check for kernel dependencies.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Rui Salvaterra [Thu, 1 Apr 2021 13:36:32 +0000 (14:36 +0100)]
zram-swap: clean up the makefile
Break dependencies into separate lines, to improve the readability. Trim
trailing whitespace.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Andreas Böhler [Thu, 23 Jan 2020 20:20:38 +0000 (21:20 +0100)]
lantiq: add basic support for AVM FRITZ!Box 3390
The FRITZ!Box 3390 actually contains two SoCs, one Lantiq with a
5GHz WiFi and one AR9342 with a 2.4GHz WiFi. Only the Lantiq
has access to the flash memory, the Atheros runs fully from RAM.
Specifications
--------------
- Lantiq 500 MHz
- 128MiB RAM
- 128MiB NAND
- 256k Flash
- AR9580 5GHz WiFi
- AR9342 560 MHz
- 64MiB RAM
- AR9328 2.4GHz WiFi
Remarks
-------
This commit only adds support for the Lantiq side of things and
prepares the drivers for communication with the Atheros SoC. Thus,
only 5GHz WiFi works by default, the 2.4GHz WiFi will be added via
another target.
Some kernel patches will be required to add support for the Atheros SoC.
Installation
------------
Use the eva_ramboot.py script to boot the initramfs image. Then, transfer
the sysupgrade image to the device and run sysupgrade to flash it to the
NAND.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Acked-by: Aleksander Jan Bajkowski A.Bajkowski@stud.elka.pw.edu.pl
Signed-off-by: Joachim Cerny <cocktail_yogi@web.de>
Joachim Cerny [Tue, 8 Dec 2020 16:41:56 +0000 (17:41 +0100)]
lantiq: VR9: fix gpio-hog by defining the GPIO ranges
defined gpio-ranges according to Reference: https://github.com/torvalds/linux/blob/master/drivers/pinctrl/pinctrl-xway.c#L864
This change is needed by gpio-hog on Fritzbox 3390
thx to @abajk
Acked-by: Aleksander Jan Bajkowski A.Bajkowski@stud.elka.pw.edu.pl
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Signed-off-by: Joachim Cerny <cocktail_yogi@web.de>
Jeroen Peelaerts [Tue, 9 Feb 2021 22:33:51 +0000 (23:33 +0100)]
lantiq: use ActualNetDataRate for speed reporting
Switch to Actual Net Data Rate (ACTNDR) for speed reporting on lantiq VDSL modems
Refer to ITU-T G.997.1 chapter 7.5.2.8
Independent whether retransmission is used or not in a given transmit direction:
- In L0 state, this parameter reports the Net Data Rate (as specified in G.992.3, G.992.5 or G.993.2) at which the bearer channel is operating.
- In L2 state, the parameter contains the Net Data Rate (as specified in G.992.3, G.992.5 or G.993.2) in the previous L0 state.
Signed-off-by: Jeroen Peelaerts <jeroen.peelaerts@gmail.com>
Reviewed-by: Andre Heider <a.heider@gmail.com>
Jeroen Peelaerts [Sat, 16 May 2020 10:12:46 +0000 (12:12 +0200)]
lantiq: enable G.INP retransmission counters
This commit adds monitoring for a couple of DSL line features that are
present in the lantiq firmware blobs.
* G.INP ON/OFF
* Trellis encoding ON/OFF
* Virtaul Noise ON/OFF
* Bitswap ON/OFF
Difference in size for ltq-vdsl-app = 1k
Difference in size for kmod-ltq-vdsl-vr9 < 1k
Reviewed-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Jeroen Peelaerts <jeroen.peelaerts@gmail.com>
Shiji Yang [Thu, 4 Mar 2021 09:59:14 +0000 (17:59 +0800)]
ramips: fix IMAGE_SIZE of HC5x6: fix image size of HC5x61
"firmware" partition size defined in the device tree file is 0xf70000,
so the right IMAGE_SIZE is 15808k
Fixes: df1e5d646345 ("ramips: fix partition layout of hiwifi hc5x61")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Daniel Engberg [Fri, 19 Mar 2021 11:18:02 +0000 (12:18 +0100)]
ramips: Fix booting on MQmaker WiTi board
This fixes the dreaded "lzma error 1" also reported on similar devices
Ref: https://bugs.openwrt.org/index.php?do=details&task_id=3057
Fixes: FS#3057
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
René van Dorst [Sat, 20 Mar 2021 19:15:14 +0000 (20:15 +0100)]
ramips: Fix booting on MTC WR1201
This fixes the dreaded "lzma error 1" also reported on similar devices
Ref: https://bugs.openwrt.org/index.php?do=details&task_id=3057
Fixes: FS#3057
Signed-off-by: René van Dorst <opensource@vdorst.com>
Aleksander Jan Bajkowski [Fri, 5 Mar 2021 19:16:35 +0000 (20:16 +0100)]
armvirt: add 5.10 testing kernel
Add 5.10 as testing kernel. Builds successfully with
CONFIG_ALL_KMODS=y enabled.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Aleksander Jan Bajkowski [Fri, 5 Mar 2021 19:18:20 +0000 (20:18 +0100)]
armvirt: refresh 5.10 config
This was done by executing these commands:
$ make kernel_oldconfig CONFIG_TARGET=subtarget
$ make kernel_oldconfig CONFIG_TARGET=subtarget_platform
Some common symbols have been moved to target config.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Aleksander Jan Bajkowski [Fri, 19 Mar 2021 18:44:12 +0000 (19:44 +0100)]
armvirt: copy config files for 5.10
Copy config and patches for 5.10.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Aleksander Jan Bajkowski [Thu, 4 Mar 2021 23:51:04 +0000 (00:51 +0100)]
armvirt: refresh 5.4 config
This was done by executing these commands:
$ make kernel_oldconfig CONFIG_TARGET=subtarget
$ make kernel_oldconfig CONFIG_TARGET=subtarget_platform
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Alexander Egorenkov [Sun, 28 Mar 2021 08:45:08 +0000 (10:45 +0200)]
base-files: fix status display command
If service() is called w/o parameter then the status display for services
with multiple instances is incorrect. E.g. samba4 or wpad have 2 instances.
root@OpenWrt:~# /etc/init.d/samba4 status
running
root@OpenWrt:~# /etc/init.d/wpad status
running
Before change:
/etc/init.d/samba4 enabled stopped
/etc/init.d/wpad enabled stopped
After change:
/etc/init.d/samba4 enabled running
/etc/init.d/wpad enabled running
Signed-off-by: Alexander Egorenkov <egorenar-dev@posteo.net>
Tony Ambardar [Sat, 27 Mar 2021 12:43:03 +0000 (05:43 -0700)]
iproute2: fix libbpf detection with NLS enabled
Upstream iproute2 detects libbpf using a one-line $CC test-compile, which
normally ignores LDFLAGS. With NLS enabled however, LDFLAGS includes an
"rpath-link" linker option needed to resolve libintl.so. Its absence
causes both the compile and libbpf detection to fail:
ld: warning: libintl.so.8, needed by libbpf.so, not found (try using
-rpath or -rpath-link)
ld: libelf.so.1: undefined reference to `libintl_dgettext'
collect2: error: ld returned 1 exit status
Fix this by directly including $LDFLAGS in the test-compile command.
Reported-by: Ian Cooper <iancooper@hotmail.com>
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Tony Ambardar [Sun, 28 Mar 2021 07:40:31 +0000 (00:40 -0700)]
binutils: fix libbfd missing DSO dependency if NLS enabled
The libbfd package definition uses $(ICONV_DEPENDS) and $(INTL_DEPENDS)
but links against neither, leading to libbfd detection failures in other
packages (e.g. bpftools) and on-target relocation problems with libintl.so:
root@OpenWrt:/# ldd /usr/lib/libbfd.so
ldd (0x77db6000)
libc.so => ldd (0x77db6000)
libgcc_s.so.1 => /lib/libgcc_s.so.1 (0x77c6d000)
Error relocating /usr/lib/libbfd.so: libintl_dgettext: symbol not found
Add NLS-conditional linking of "libintl" to fix this. Also remove libbfd
package dependency $(ICONV_DEPENDS) which is not used during building or
linking.
Tested with QEMU on malta/be32, after building all packages from binutils,
bpftools and iproute2, using different libc options musl and glibc.
Fixes: 08e817569630 ("binutils: use nls.mk to fix libbfd link errors in
other packages")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Tony Ambardar [Sun, 28 Mar 2021 08:12:22 +0000 (01:12 -0700)]
bpftools: drop unneeded libintl linking for NLS
There is no direct linking of libintl from bpftools, only secondary linking
through libelf, so remove "-lintl" from TARGET_LDFLAGS.
Fixes: 5582fbd6135f ("bpftools: support NLS, fix ppc build and update to 5.8.9")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
John Audia [Tue, 30 Mar 2021 14:52:07 +0000 (10:52 -0400)]
kernel: bump 5.4 to 5.4.109
Ran update_kernel.sh in a fresh clone without any existing toolchains.
Manually rebased:
pending-5.4/611-netfilter_match_bypass_default_table.patch
The upstream change affecting this patch is the revert of an earlier
kernel commit. Therefore, we just revert our corresponding changes
in [1].
Build system: x86_64
Build-tested: ipq806x/R7800
[1]
9b1b89229f0e ("kernel: bump 5.4 to 5.4.86")
Signed-off-by: John Audia <graysky@archlinux.us>
[adjust manually rebased patch, add explanation]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Vivek Unune [Fri, 13 Nov 2020 13:43:00 +0000 (08:43 -0500)]
bcm53xx: enhance support for Linksys EA9500
1. Add leds and configs
2. Add network configs
3. Add script to clear partial boot flag
4. Hack to use port 5 as cpu port as port 8 connected to eth2
wont pass any frames
5. Enable EA9500 image generation
Hardware Info:
- Processor - Broadcom BCM4709C0KFEBG dual-core @ 1.4 GHz
- Switch - BCM53012 in BCM4709C0KFEBG & external BCM53125
- DDR3 RAM - 256 MB
- Flash - 128 MB (Toshiba TC58BVG0S3HTA00)
- 2.4GHz - BCM4366 4×4 2.4/5G single chip 802.11ac SoC
- Power Amp - Skyworks SE2623L 2.4 GHz power amp (x4)
- 5GHz x 2 - BCM4366 4×4 2.4/5G single chip 802.11ac SoC
- Power Amp - PLX Technology PEX8603 3-lane, 3-port PCIe switch
- Ports - 8 Ports, 1 WAN Ports
- Antennas - 8 Antennas
- Serial Port - @j6 [GND,TX,RX] (VCC NC) 115200 8n1
Flashing Instructions:
1. Connect a USB-TTL table to J6 on the router as well as a
ethernet cable to a lan port and your PC.
2. Power-on the router.
3. Use putty or a serial port program to view the terminal.
Hit Ctrl+C and interrupt the CFE terminal terminal.
4. Setup a TFTP server on your local machine at setup you
local IP to 192.168.1.2
5. Start the TFTP Server
6. Run following commands at the CFE terminal
flash -noheader 192.168.1.2:/openwrt.trx nflash0.trx
flash -noheader 192.168.1.2:/openwrt.trx nflash0.trx2
nvram set bootpartition=0 && nvram set partialboots=0 && nvram commit
7. Reboot router to be presented by OpenWrt
Note: Only installation method via serial cable is supported at the moment.
The trx firmware has to be flashed to both the partitions using following
commands from CFE prompt. This will cover US and Non-US variants.
Signed-off-by: Vivek Unune <npcomplete13@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Thu, 1 Apr 2021 05:00:06 +0000 (07:00 +0200)]
bcm53xx: use upstream Linksys EA9500 fixes
One fix was accepted, one was added.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Jo-Philipp Wich [Wed, 31 Mar 2021 22:21:55 +0000 (00:21 +0200)]
firewall4: update to latest Git HEAD
29fba84 tests: expand testing
6bf82a8 fw4.uc: fix family test functions
25b2c7d fw4.uc: fix parsing boolean "0" values
694d428 rule.uc: fix redundant whitespace in rules without target
7f69fbb ruleset.uc: reduce empty lines in output
8f8e42c fw4.uc: gracefully handle missing defaults section
25287af treewide: remove ucode module preloading
802b685 fw4.uc: remove upvalue caching
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Jo-Philipp Wich [Wed, 31 Mar 2021 22:07:56 +0000 (00:07 +0200)]
ucode: update to latest Git HEAD
973cc6c compiler: actually expand block scope fix to for/while alt syntax
97bf297 compiler: ensure that alternative if/for/while syntax has own block scope
f0e2a64 tests: add missing test case for fixed switch codegen
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Daniel Golle [Wed, 31 Mar 2021 20:32:23 +0000 (21:32 +0100)]
uboot-mediatek: adapt root= cmdline arg for bpi-r64
Adapt to FIT partition parser changes.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Wed, 31 Mar 2021 20:29:26 +0000 (21:29 +0100)]
kernel: fix FIT partition parser compatibility issues
The uImage.FIT partition parser used to squeeze in FIT partitions in
the range where partition editor tools (fdisk and such) expect the
regular partition. This is confusing people and tools when adding
additional partitions on top of the partition used for OpenWrt's
uImage.FIT.
Instead of squeezing in the additional partitions, rather start with
all uImage.FIT partitions at offset 64.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Rafał Miłecki [Wed, 31 Mar 2021 21:14:24 +0000 (23:14 +0200)]
bcm4908: backport DT patch adding Ethernet MAC address
This tells OS (Linux) where from MAC should be read (bootloader MTD
partition).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Daniel Golle [Wed, 31 Mar 2021 13:19:16 +0000 (14:19 +0100)]
mediatek: mt7622: improve sysupgrade on MMC
Use generic functions to acquire rootdev.
Make sure to wipe rootfs_data in case of '-n'.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Wed, 31 Mar 2021 12:47:35 +0000 (13:47 +0100)]
base-files: functions: introduce new helper functions
Introduce cmdline_get_var() to /lib/function.sh and make use of it in
export_rootdev() in /lib/upgrade/common.sh, making the code more
simple and removing one level of indentation.
Introduce get_partition_by_name() to /lib/upgrade/common.sh which is
useful on non-EFI GPT platforms like mt7622.
Remove some dead-code while at it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Álvaro Fernández Rojas [Wed, 31 Mar 2021 15:13:36 +0000 (17:13 +0200)]
bmips: backport pinctrl fixes
Backport some minor upstream fixes for the pinctrl drivers.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Daniel Golle [Wed, 31 Mar 2021 00:32:51 +0000 (01:32 +0100)]
netifd: update to git HEAD
09632d4 device: remove left-over comment
b22f83d handler: add mechanism to generate external device handler stubs
80bf9d7 extdev: add support for external device handlers
44c0f40 system-linux: reorder sysctl functions
c84f3b0 system-linux: add device options used by wpad
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Ilya Lipnitskiy [Fri, 26 Mar 2021 06:23:01 +0000 (23:23 -0700)]
ramips: mt7620: ralink-i2s: fix modpost error
Fixes the following error when building without CONFIG_MODULE_STRIPPED:
FATAL: modpost: sound/soc/ralink/snd-soc-ralink-i2s: struct
of_device_id is not terminated with a NULL entry!
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Rui Salvaterra [Tue, 30 Mar 2021 22:59:50 +0000 (23:59 +0100)]
ramips/mt7621: enable support for cpuidle
MIPS Coherent Processor Systems (CPS), which include the MT7621 SoC, support
deep sleep idle states and have a specific cpuidle driver for them.
Enable support for it, while also switching from constant timer ticks to the
idle dynticks model, with the TEO governor.
Run-tested on a Redmi AC2100.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Rui Salvaterra [Tue, 30 Mar 2021 22:59:49 +0000 (23:59 +0100)]
ramips/mt7621: drop the timer recalibration patch
We've been carrying this patch for many years [1], in order to fix a timer
calibration issue on MT7621. Turns out, after retesting with a recent kernel
(Linux 5.10), the system works perfectly fine without it (no rcu_sched stalls
or inconsistent BogoMIPS values across CPUs).
Manually refreshed:
322-mt7621-fix-cpu-clk-add-clkdev.patch
323-mt7621-memory-detect.patch
[1] https://git.openwrt.org/?p=openwrt/openwrt.git;a=commitdiff;h=
6f4a903533361a2906a4d94ac6f597cd9c6c47bc
Suggested-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Tested-by: Donald Hoskins <grommish@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Rui Salvaterra [Tue, 30 Mar 2021 22:59:48 +0000 (23:59 +0100)]
ramips/mt7621: drop the weak reordering patch
In order to fix random hangs on MT7621, we've been selecting
WEAK_REORDERING_BEYOND_LLSC for years [1]. However, these random hangs have been
most likely caused by an oversight in the MIPS implementation of the kernel
memory consistency model, which has already been fixed for some time (and
backported to stable) [2].
Manually refreshed:
321-mt7621-timer.patch
[1] https://git.openwrt.org/?p=openwrt/openwrt.git;a=commitdiff;h=
5c971cd6fdd7298a2017bdb6bea870088eddb8b9
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/mips?h=linux-5.4.y&id=
42344113ba7a1ed7b5654cd5270af0d5698d8521
Suggested-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Tested-by: Donald Hoskins <grommish@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Hans Dedecker [Mon, 29 Mar 2021 19:04:06 +0000 (21:04 +0200)]
firewall: update to latest git HEAD
a4355a6 firewall3: clean up the flow table detection logic
edd0dc5 firewall3: create a common helper to find strings in files
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Paul Spooren [Mon, 29 Mar 2021 08:31:21 +0000 (22:31 -1000)]
ncurses: add screen-256color terminfo
The terminfo is required by the popular terminal multiplexer screen and
tmux, offer it by default as the size impact is minimal with 885 Bytes.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Paul Spooren [Mon, 29 Mar 2021 08:21:49 +0000 (22:21 -1000)]
ncurses: split long line of supported terminfo
The terminfo files were all in one row which is terrible to read.
Split them over multiple lines to improve readability.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Zoltan HERPAI [Sun, 28 Feb 2021 15:42:05 +0000 (16:42 +0100)]
sunxi: enable wifi module on Pine64 boards
The Pine64(+) and the SoPine64 baseboard has an optional BT+WiFi
module, carrying an RTL8723BS. The wifi part is connected via
SDIO, the BT part is connected via UART. The BT part requires
additional code changes in the drivers so we'll skip that until 5.10.
Aside from a DTS patch to enable the wifi module, add the required
packages into the device definitions.
[ 8.996970] RTL8723BS: module init start
[ 9.000922] RTL8723BS: rtl8723bs v4.3.5.5_12290.20140916_BTCOEX20140507-4E40
[ 9.007965] RTL8723BS: rtl8723bs BT-Coex version = BTCOEX20140507-4E40
[ 9.014785] pnetdev =
000000009bdd5000
[ 9.047780] RTL8723BS: rtw_ndev_init(wlan0)
[ 9.053349] RTL8723BS: module init ret =0
root@OpenWrt:/# iw list
Wiphy phy0
wiphy index: 0
max # scan SSIDs: 9
max scan IEs length: 2304 bytes
max # sched scan SSIDs: 0
max # match sets: 0
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Available Antennas: TX 0 RX 0
Supported interface modes:
* IBSS
* managed
* AP
* monitor
Band 1:
Frequencies:
* 2412 MHz [1] (20.0 dBm)
* 2417 MHz [2] (20.0 dBm)
* 2422 MHz [3] (20.0 dBm)
* 2427 MHz [4] (20.0 dBm)
* 2432 MHz [5] (20.0 dBm)
* 2437 MHz [6] (20.0 dBm)
* 2442 MHz [7] (20.0 dBm)
* 2447 MHz [8] (20.0 dBm)
* 2452 MHz [9] (20.0 dBm)
* 2457 MHz [10] (20.0 dBm)
* 2462 MHz [11] (20.0 dBm)
* 2467 MHz [12] (20.0 dBm) (no IR)
* 2472 MHz [13] (20.0 dBm) (no IR)
* 2484 MHz [14] (20.0 dBm) (no IR)
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Zoltan HERPAI [Sun, 28 Feb 2021 11:51:27 +0000 (12:51 +0100)]
sunxi: enable MUSB in A53 subtarget
The Pine64(+) and the SoPine64 baseboard has two USB ports. One of
these (the lower) is connected directly to a USB host, the other
one's (upper) PHY is shared with the separate OTG controller. In
order to get it working, MUSB support needs to be enabled.
As there are other targets which compile MUSB support into the kernel
and not package it into modules, the same is done here.
[ 1.348760] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.04
[ 1.357029] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.364250] usb usb5: Product: MUSB HDRC host driver
[ 1.369219] usb usb5: Manufacturer: Linux 5.4.99 musb-hcd
[ 1.374617] usb usb5: SerialNumber: musb-hdrc.1.auto
[ 1.379891] hub 5-0:1.0: USB hub found
[ 1.383677] hub 5-0:1.0: 1 port detected
[...]
[ 697.299440] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 697.461855] usb 1-1: New USB device found, idVendor=090c, idProduct=1000, bcdDevice=11.00
[ 697.470038] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 697.477180] usb 1-1: Product: USB Flash Disk
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Álvaro Fernández Rojas [Wed, 24 Mar 2021 10:30:23 +0000 (11:30 +0100)]
bmips: dts: align LEDs
Align all bmips devices LED configurations.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Álvaro Fernández Rojas [Tue, 2 Mar 2021 19:19:30 +0000 (20:19 +0100)]
bmips: backport accepted pinctrl patches
These patches have been accepted for linux v5.13.
External interrupts not supported for now.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Álvaro Fernández Rojas [Wed, 24 Mar 2021 10:11:47 +0000 (11:11 +0100)]
bmips: vr-3032u: fix gpio keys
These GPIO keys were assigned to incorrect pins.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Álvaro Fernández Rojas [Wed, 24 Mar 2021 10:09:27 +0000 (11:09 +0100)]
bmips: dgnd3700-v2: fix gpio keys
These GPIO keys were assigned to incorrect pins.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Jo-Philipp Wich [Mon, 29 Mar 2021 10:50:55 +0000 (12:50 +0200)]
ucode: update to latest Git HEAD
aa9621d compiler: rework switch statement code generation
b5f0de1 vm: add trace mode instruction dump output fixes
0341d64 vm: fix another for-loop memory leak
00d9419 vm: fix further memory leaks in trace mode
20a3763 vm: fix loop variable memory leak in NEXTK/NEXTKV instruction
9a6ef2b lib: prevent use-after-free after uc_shift()
03f1324 object: free prototype object when registering existing ressource type
b3d758b compiler: fix for/break miscompilation
86e3970 lib: fix value refcount of uc_unshift() return value
fe464ea run_tests.sh: allow passing tests to run as arguments
091ae1b compiler: fix another try/catch miscompilation
fcedb19 lib: fix passing uninitialized memory to sigprocmask()
0d0357d vm: fix leaking source context strings in trace mode
7a41fb3 lib: use execvp() in system()
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Rafał Miłecki [Mon, 29 Mar 2021 07:28:47 +0000 (09:28 +0200)]
bcm53xx: fix Linksys EA9500 partitions
Use proper DT binding.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Mon, 29 Mar 2021 06:16:17 +0000 (08:16 +0200)]
kernel: backport 5.13 mtd partitioning changes
1. Use upstream accepted NVMEM patches
2. Minor fix for BCM4908 partitioning
3. Support for Linksys firmware partitions on Northstar
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Felix Fietkau [Sun, 28 Mar 2021 10:15:42 +0000 (12:15 +0200)]
mac80211: merge a few pending tx related fixes
Improve performance and fix potential mgmt tx hangs/warnings
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Tony Ambardar [Fri, 26 Mar 2021 05:47:36 +0000 (22:47 -0700)]
firewall3: update to latest git HEAD
This includes several improvements and fixes:
61db17e rules: fix device and chain usage for DSCP/MARK targets
7b844f4 zone: avoid duplicates in devices list
c2c72c6 firewall3: remove last remaining sprintf()
12f6f14 iptables: fix serializing multiple weekdays
00f27ab firewall3: fix duplicate defaults section detection
e8f2d8f ipsets: allow blank/commented lines with loadfile
8c2f9fa fw3: zones: limit zone names to 11 bytes
78d52a2 options: fix parsing of boolean attributes
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Sven Eckelmann [Thu, 25 Mar 2021 12:26:15 +0000 (13:26 +0100)]
mvebu: Fix mac addresses for GL.iNet GL-MV1000
The original GL.iNet firmware has two different mac addresses in the
factory/art partition. The first one is for the WAN interface only and the
second one is for both lan0 and lan1.
But the original submission for OpenWrt didn't initialize the mac
addresses of the LAN ports for the DSA device at all. The ethernet mac
address was then used for all DSA ports.
Fixes: 050c24f05c85 ("mvebu: add support for GL.iNet GL-MV1000")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Shiji Yang [Sun, 21 Mar 2021 09:01:49 +0000 (17:01 +0800)]
ramips: correct switch config of Youku yk1
There are only two lan ports and one wan port on Youku yk1
Fixes: e9baf8265bb8 ("ramips: add support for Youku YK1")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[add Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
John Audia [Wed, 24 Mar 2021 14:14:36 +0000 (10:14 -0400)]
kernel: bump 5.4 to 5.4.108
All modifications made by by update_kernel.sh.
Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800 [only 5.4.107]
No dmesg regressions, everything functional
Run-tested by @timocapa:
- ramips/mt7621/{Xiaomi R3G, Redmi 2100}
- Lantiq/XWAY/Fritz!Box 7320/7330
Signed-off-by: John Audia <graysky@archlinux.us>
[squash, edit commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
INAGAKI Hiroshi [Wed, 24 Mar 2021 15:15:57 +0000 (00:15 +0900)]
ath79: fix label_mac for NEC Aterm WG1200CR
On NEC Aterm WG1200CR, the MAC address for WAN is printed in the label
on the case, not LAN.
This patch fixes this issue.
Fixes: 50fdc0374b ("ath79: provide label MAC address")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Sven Eckelmann [Thu, 25 Mar 2021 12:26:15 +0000 (13:26 +0100)]
mvebu: Add button support for GL.iNet GL-MV1000
The original patch to support this device advertised support for the reset
button and the "switch" in the commit message. But neither were actually
integrated in the device tree or documented anywere.
The button itself is now used to trigger a reset (as described in the
official GL.iNet documentation). The switch itself is registered as BTN_0
like other devices from GL.iNet in ath79.
Fixes: 050c24f05c85 ("mvebu: add support for GL.iNet GL-MV1000")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Hauke Mehrtens [Thu, 25 Mar 2021 10:31:23 +0000 (11:31 +0100)]
kernel: Move CONFIG_USERIO to generic config
The CONFIG_USERIO option is unset in multiple target configurations. On
the sunxi target it is activated. Move the kernel configuration option
to the generic kernel configuration.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Thu, 25 Mar 2021 10:27:31 +0000 (11:27 +0100)]
kernel: Deactivate CONFIG_VFIO in generic kernel config
Instead of deactivating this in every target config, deactivate it once
in the generic kernel config. I was asked for this config option in a
x86 64 build in OpenWrt 21.02.
Fixes: 87046e87e229 ("kernel: add missing kernel config symbol")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Kevin Darbyshire-Bryant [Sat, 27 Mar 2021 08:47:47 +0000 (08:47 +0000)]
kernel: add missing kernel config symbol
Bump to 5.10.26 reversed dependencies on IOMMU for CONFIG_VFIO thus
malta (at least) prompted for this new symbol.
Set it to 'false' in the default config. rockchip & X86 enable it in
target specific configs.
Thanks to Tony Ambardar for falling over this one
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Felix Fietkau [Fri, 26 Mar 2021 20:56:26 +0000 (21:56 +0100)]
mt76: update to the latest version
6886b57a1534 mt76: connac: introcuce mt76_sta_cmd_info data structure
e529e8afe22a mt76: mt7921: properly configure rcpi adding a sta to the fw
e4d522776804 mt76: mt7921: fix airtime reporting
be2f67e8d3cb mt76: mt7915: fix key set/delete issue
09a1befde4b7 mt76: fix potential DMA mapping leak
f66f8f41d47b mt76: mt7915: refresh repeater entry MAC address when setting BSSID
035e2f6f1ddf mt76: mt7921: get rid of mt7921_mac_wtbl_lmac_addr
ee29cd5f3a6a mt76: mt7615: only enable DFS test knobs for mt7615
9a98b1a6f9c2 mt76: mt7615: cleanup mcu tx queue in mt7615_dma_reset()
3bd285424e7b mt76: mt7622: trigger hif interrupt for system reset
bf6d9ee4acd1 mt76: mt7615: keep mcu_add_bss_info enabled till interface removal
115b74282314 mt76: mt7915: keep mcu_add_bss_info enabled till interface removal
57432e701d1a mt76: mt7915: cleanup mcu tx queue in mt7915_dma_reset()
a519c49a6a42 mt76: mt7615: 0-terminate firmware log messages
4a22f2ffae2e mt76: mt7915: 0-terminate firmware log messages
b8609066893a mt76: mt7615: fix chip reset on MT7622 and MT7663e
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Stan Grishin [Wed, 24 Mar 2021 16:18:08 +0000 (16:18 +0000)]
x86/base-files: add support for Sophos SG/XG-105
This adds detection of the Sophos SG-105 and Sophos XG-105 models
and assignment of ethernet ports these models have to LAN/WAN.
Signed-off-by: Stan Grishin <stangri@melmac.net>
Eneas U de Queiroz [Fri, 26 Mar 2021 17:46:29 +0000 (14:46 -0300)]
openssl: bump to 1.1.1k
This version fixes 2 security vulnerabilities, among other changes:
- CVE-2021-3450: problem with verifying a certificate chain when using
the X509_V_FLAG_X509_STRICT flag.
- CVE-2021-3449: OpenSSL TLS server may crash if sent a maliciously
crafted renegotiation ClientHello message from a client.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Petr Štetiar [Thu, 25 Mar 2021 07:01:08 +0000 (08:01 +0100)]
README: add install command to build requirements
In commit
8c8496435a9d ("build: add GNU install to prerequisites") new
dependency was added, but addition to README was omitted.
Fixes: 8c8496435a9d ("build: add GNU install to prerequisites")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Kevin Darbyshire-Bryant [Fri, 26 Mar 2021 09:12:12 +0000 (09:12 +0000)]
Revert "openssl: refresh patches"
This reverts commit
e27ef2da0d513494c3e9926ce8d44b63e4236a32.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Kevin Darbyshire-Bryant [Fri, 26 Mar 2021 08:58:07 +0000 (08:58 +0000)]
openssl: refresh patches
Tidy up some patch fuzz.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Tony Ambardar [Wed, 24 Feb 2021 16:52:22 +0000 (08:52 -0800)]
elfutils: enable building with MIPS16
Building with MIPS16 was disabled in 2013 due to an issue with GCC TLS:
https://dev.archive.openwrt.org/ticket/13572. But after the problematic
GCC version was retired, this change wasn't revisited.
Re-enable MIPS16 builds to reduce average elfutils library sizes ~10%.
This was compile-tested on malta/mips32be and malta/mips32le, and linked
with iproute2 for run-testing. Package sizes follow:
Library MIPS16:=0 MIPS16:=1
------- --------- ---------
libelf1 43217 37492
libasm1 12481 11658
libdw1 229723 205793
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Rui Salvaterra [Thu, 25 Mar 2021 09:32:18 +0000 (09:32 +0000)]
kernel: bump 5.10 to 5.10.26
Automatically refreshed:
ath79/patches-5.10/471-mtd-cfi_cmdset_0002-AMD-chip-0x2201-write-words.patch
bcm63xx/patches-5.10/143-gpio-fix-device-tree-gpio-hogs-on-dual-role-gpio-pin.patch
generic/hack-5.10/204-module_strip.patch
Run-tested:
ath79 (TL-WDR3600)
x86_64 (APU2 - ldir)
Tested-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Paul Spooren [Thu, 25 Mar 2021 20:25:54 +0000 (10:25 -1000)]
build,json: 3rd fixup of default_packages
This became a bit of a tragedy, caused by a corner cases which wasn't
put into account during testing. DEFAULT_PACKAGES are defined in
target/linux/<target>/Makefile but also in
target/linux/<target>/<subtarget>/target.mk.
The latter was no longer imported when using DUMP=1, however not using
DUMP=1 while running the Makefile in target/linux/<target>/ caused duplicate
packages in the list.
As a solution, which should have been used from day 0, `make` runs in
target/linux/ without DUMP=1, resulting in no duplicate packages and all
inclusions from include/target.mk, linux/target/<target>/{Makefile,
<subtarget>/target.mk}
While at it, sort the list of default packages.
Signed-off-by: Paul Spooren <mail@aparcar.org>
projects / openwrt / staging / thess.git / log