Mark Menzynski [Fri, 2 Aug 2019 09:21:00 +0000 (11:21 +0200)]
drm/nouveau/volt: Fix for some cards having 0 maximum voltage
Some, mostly Fermi, vbioses appear to have zero max voltage. That causes Nouveau to not parse voltage entries, thus users not being able to set higher clocks.
When changing this value Nvidia driver still appeared to ignore it, and I wasn't able to find out why, thus the code is ignoring the value if it is zero.
CC: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Mark Menzynski <mmenzyns@redhat.com>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Lyude Paul [Wed, 7 Aug 2019 23:47:06 +0000 (19:47 -0400)]
drm/nouveau/dispnv50: Fix runtime PM ref tracking for non-blocking modesets
This is something that got noticed a while ago back when I was fixing a
large number of runtime PM related issues in nouveau, but never got
fixed:
https://patchwork.freedesktop.org/series/46815/#rev7
It's not safe to iterate the entire list of CRTCs in
nv50_disp_atomic_commit(), as we could be doing a non-blocking modeset
on one CRTC in parallel with one or more other CRTCs. Likewise, this
means it's also not safe to do so in order to track runtime PM state.
While this code is certainly wrong, so far the only issues I've seen
this cause in the wild is the occasional PM ref unbalance after an
atomic check failure + module reloading (since the PCI device will
outlive nouveau in such scenarios).
So, do this far more elegantly: grab a runtime PM ref across the modeset
and commit tail, then grab/put references for each CRTC enable/disable.
This also ends up being much simpler then the previous broken solution
we had.
Finally, since we've removed all it's users: get rid of
nouveau_drm->have_disp_power_ref.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Lyude Paul [Wed, 7 Aug 2019 23:47:05 +0000 (19:47 -0400)]
drm/nouveau/dispnv04: Remove runtime PM
Originally when trying to fix the issue of runtime PM references with
non-blocking CRTCs on nv50, I ended up stumbling on this code when
trying to remove nouveau_drm->have_disp_power_ref, and attempted to fix
it to remove the dependency on have_disp_power_ref. However, Ilia Mirkin
pointed out that this code is actually completely useless, as pre-nv50
never had runtime PM support in the first place! Go figure.
So, since it's useless just get rid of it. Note that since the only
thing nouveau_crtc_set_config() was doing was grabbing a runtime PM ref,
calling drm_crtc_helper_set_config() then dropping the ref; we can just
remove the function entirely and just call drm_crtc_helper_set_config()
directly.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Mark Menzynski [Thu, 18 Jul 2019 08:07:41 +0000 (10:07 +0200)]
drm/nouveau/gpio: check function 76 in the power check as well
Added GPIO is "Power Alert". It's uncertain if this
GPIO is set on GPU initialization or only if a change is detected by the
GPU at runtime.
This GPIO can be found on Tesla and sometimes on Fermi GPUs.
Untested, wrote according to documentation.
Signed-off-by: Mark Menzynski <mmenzyns@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Mark Menzynski [Thu, 18 Jul 2019 08:07:40 +0000 (10:07 +0200)]
drm/nouveau/gpio: check the gpio function 16 in the power check as well
Added GPIO is "Thermal and External Power Detect". It's uncertain if this
GPIO is set on GPU initialization or only if a change is detected by the
GPU at runtime.
This GPIO can be found in Rankine and Curie and rarely on Tesla GPUs
VBIOS.
Untested, wrote according to documentation.
Signed-off-by: Mark Menzynski <mmenzyns@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Mark Menzynski [Thu, 18 Jul 2019 08:07:39 +0000 (10:07 +0200)]
drm/nouveau/gpio: fail if gpu external power is missing
Currently, nouveau doesn't check if GPU is missing power. This
patch makes nouveau fail when this happens on latest GPUs.
It checks GPIO function 121 (External Power Emergency), which
should detect power problems on GPU initialization.
This can be disabled with nouveau.config=NvPowerChecks=1
Tested on TU104, GP106 and GF100.
v3:
* Add config override for disabling power checks
Signed-off-by: Mark Menzynski <mmenzyns@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Mark Menzynski [Thu, 18 Jul 2019 08:07:38 +0000 (10:07 +0200)]
drm/nouveau/bios/gpio: sort gpios by values
One gpio was in wrong place, moved it for better readability.
Signed-off-by: Mark Menzynski <mmenzyns@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Tue, 2 Jul 2019 04:19:12 +0000 (14:19 +1000)]
drm/nouveau/therm: don't attempt fan control where PMU is already managing it
There's already a condition in place which attempts to detect this, but
since we've begun to require a PMU subdev even on boards where we don't
load a custom FW, it's become inaccurate.
This will prevent unnecessarily running a periodic fan update thread on
GP100 and newer, where we don't yet override the default PMU FW.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Tue, 2 Jul 2019 02:52:11 +0000 (12:52 +1000)]
drm/nouveau/therm: skip probing for devices not specified in thermal tables
Saves some time during driver load, as described by the relevant section[1]
of the DCB 4.x specification.
[1] https://nvidia.github.io/open-gpu-doc/DCB/DCB-4.x-Specification.html#_i2c_device_table
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Wed, 12 Jun 2019 07:37:23 +0000 (17:37 +1000)]
drm/nouveau/kms/gv100-: attach pixel blend mode property to planes
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Tue, 11 Jun 2019 07:13:04 +0000 (17:13 +1000)]
drm/nouveau/kms/gv100-: attach alpha property to planes
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Tue, 11 Jun 2019 06:46:13 +0000 (16:46 +1000)]
drm/nouveau/kms/gv100-: add support for plane zpos property
Has a nice side-effect that we only update HW for this when it changes now,
rather than every time we do a page flip.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Tue, 11 Jun 2019 06:40:31 +0000 (16:40 +1000)]
drm/nouveau/kms/nv50-: attach immutable zpos property to planes
Defaulting to the fixed layout enforced in HW by EVO, and that we
currently use by default on NVD.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Tue, 11 Jun 2019 07:03:21 +0000 (17:03 +1000)]
drm/nouveau/kms/nv50-: create primary plane before overlay planes
zpos normalisation uses plane id to determine ordering for duplicate zpos
values, and we likely want to keep primary plane on the bottom here.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Tue, 11 Jun 2019 08:04:42 +0000 (18:04 +1000)]
drm/nouveau/kms/nv50-: use __drm_atomic_helper_plane_reset()
We have some of this open-coded already, use the helper to prevent problems
when adding (for example) support for the alpha property.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Tue, 11 Jun 2019 07:46:39 +0000 (17:46 +1000)]
drm/nouveau/kms/gv100-: implement csc + enable modern colour managment properties
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Tue, 11 Jun 2019 04:54:32 +0000 (14:54 +1000)]
drm/nouveau/kms/gv100-: use premultiplied alpha blending between planes
This is apparently the assumed default behaviour when blend properties
are absent.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ilia Mirkin [Tue, 11 Jun 2019 02:32:45 +0000 (22:32 -0400)]
drm/nouveau/kms/nv50-: enable modern color management properties
For GF119:GV100, we can enable DEGAMMA/CTM/GAMMA. For earlier GPUs, as
there is no CTM, having both degamma and gamma is a bit pointless. Later
GPUs currently lack an implementation.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ilia Mirkin [Wed, 12 Jun 2019 02:40:36 +0000 (22:40 -0400)]
drm/nouveau/kms/gf119-: add ctm property support
This adds support on GF119:GV100 (exclusive) for CTM (aka CSC).
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Ilia Mirkin [Mon, 3 Jun 2019 05:59:42 +0000 (01:59 -0400)]
drm/nouveau/kms/nv50-: remove overlay alpha formats
The overlay logic can only do colorkey-based selection, not
alpha-blending.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Thu, 13 Jun 2019 04:23:04 +0000 (14:23 +1000)]
drm/nouveau/fifo/gk104-: fix parsing of mmu fault data
Pascal was particularly incorrect, as the register changed to be more in the
same format as the MMU fault buffers are.
Shouldn't have impacted much more than confusing MMU fault log messages.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Thu, 13 Jun 2019 03:58:50 +0000 (13:58 +1000)]
drm/nouveau/fifo/gf1xx: convert to using nvkm_fault_data
Would like to be able to reuse gf100_fifo_intr_fault() for (some of) the
later chipsets too, as it's identical.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Rhys Kidd [Sun, 2 Jun 2019 14:13:15 +0000 (00:13 +1000)]
drm/nouveau/bios/init: handle INIT_RESET_END devinit opcode
Signal that the reset sequence has completed.
This opcode signals that the software reset sequence has completed.
Ordinarily, no actual operations are performed by the opcode.
However it allows for possible software work arounds by devinit
engines in software agents other than the VBIOS, such as the resman,
FCODE, and EFI driver.
Signed-off-by: Rhys Kidd <rhyskidd@gmail.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Rhys Kidd [Sun, 2 Jun 2019 14:13:14 +0000 (00:13 +1000)]
drm/nouveau/bios/init: handle INIT_RESET_BEGUN devinit opcode
Signal that the reset sequence has begun.
This opcode signals that the software reset sequence has begun.
Ordinarily, no actual operations are performed by the opcode.
However it allows for possible software work arounds by devinit
engines in software agents other than the VBIOS, such as the resman,
FCODE, and EFI driver.
Signed-off-by: Rhys Kidd <rhyskidd@gmail.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Rhys Kidd [Sun, 2 Jun 2019 12:07:27 +0000 (22:07 +1000)]
drm/nouveau/bios: downgrade absence of tmds table to info from an error
Absence of a TMDS Info Table is common on Optimus setups where the NVIDIA
gpu is not connected directly to any outputs.
Reporting an error in this scenario is too harsh. Accordingly, change the
error message to an info message.
By default the error message also causes a boot flicker for these sytems.
Signed-off-by: Rhys Kidd <rhyskidd@gmail.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ville Syrjälä [Thu, 13 Sep 2018 16:31:46 +0000 (19:31 +0300)]
drm/nouveau: Disable atomic support on a per-device basis
We now have per-device driver_features, so let's use that
to disable atomic only for pre-nv50.
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: nouveau@lists.freedesktop.org
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ilia Mirkin [Tue, 28 May 2019 02:58:37 +0000 (22:58 -0400)]
drm/nouveau/kms/nv50-: add fp16 scanout support
Older hardware seems to want 0..1024 values, while new hardware takes
0..1 values. We set the gain to 1024 for the earlier display classes.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Wed, 29 May 2019 06:39:53 +0000 (16:39 +1000)]
drm/nouveau/kms/nv50-: disable input lut harder
Under some circumstances, it could be left enabled when it shouldn't be.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Wed, 29 May 2019 05:44:57 +0000 (15:44 +1000)]
drm/nouveau/kms/tu102-: disable input lut when input is already FP16
On Turing, an input LUT is required to transform inputs in fixed-point
formats to FP16 for the internal display pipe. We provide an identity
mapping whenever a window is enabled for this reason.
HW has error checks to ensure when the input is already FP16, that the
input LUT is also disabled.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Tue, 28 May 2019 06:33:59 +0000 (16:33 +1000)]
drm/nouveau/kms/gv100: allow windows to use PACKED8BPP formats
Required for upcoming FP16 scanout support.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Hariprasad Kelam [Sun, 26 May 2019 11:06:25 +0000 (16:36 +0530)]
drm/nouveau: fix nvif/device.h is included more than once
remove duplicate inclusion of nvif/device.h
Issue identified by includecheck
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Hariprasad Kelam [Sun, 26 May 2019 10:59:36 +0000 (16:29 +0530)]
drm/nouveau/dispnv04: subdev/bios.h is included more than once
remove duplicate inclusion of subdev/bios.h
Issue identified by includecheck
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Gustavo A. R. Silva [Fri, 24 May 2019 17:15:36 +0000 (12:15 -0500)]
drm/nouveau/mmu: use struct_size() helper
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.
So, replace the following form:
sizeof(*kind) + sizeof(*kind->data) * mmu->kind_nr;
with:
struct_size(kind, data, mmu->kind_nr)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Sam Ravnborg [Sun, 19 May 2019 14:00:44 +0000 (16:00 +0200)]
drm/nouveau: drop use of drmp.h
Drop use of the deprecated drmP.h file from drm/nouveau.
Build tested using allyesconfig and allmodconfig.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: nouveau@lists.freedesktop.org
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Sam Ravnborg [Sun, 19 May 2019 14:00:43 +0000 (16:00 +0200)]
drm/nouveau: drop drmP.h from all header files
Drop include of the deprecated drmP.h from all nouveau heder files.
This allows us to remove drmP.h from all .c files without any
side-effects in a follow-up commit.
Build tested using allyeyconfig and allmodconfig
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: nouveau@lists.freedesktop.org
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Sam Ravnborg [Sun, 19 May 2019 14:00:42 +0000 (16:00 +0200)]
drm/nouveau: drop drmP.h from nouveau_drv.h
Drop the deprecated drmP.h header from nouveau_drv.h.
Fix fallout in other parts of the driver.
Build tested using allmodconfig and allyesconfig.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: nouveau@lists.freedesktop.org
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Sam Ravnborg [Sun, 19 May 2019 14:00:41 +0000 (16:00 +0200)]
drm/nouveau: drop use of DRM_UDELAY
The DRM_UDELAY is a simple wrapper for udealy() and to be consistent
call udelay() direct like in may other places.
This avoids the need to pull in drm_os_linux.h when we later
drop drmP.h uses in nouveau.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: nouveau@lists.freedesktop.org
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Colin Ian King [Tue, 14 May 2019 20:57:01 +0000 (21:57 +0100)]
drm/nouveau/bios/init: fix spelling mistake "CONDITON" -> "CONDITION"
There is a spelling mistake in a warning message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
YueHaibing [Wed, 17 Jul 2019 06:56:26 +0000 (14:56 +0800)]
drm/nouveau/secboot: Make acr_r352_ls_gpccs_func static
Fix sparse warning:
drivers/gpu/drm/nouveau/nvkm/subdev/secboot/acr_r352.c:1092:1:
warning: symbol 'acr_r352_ls_gpccs_func' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Dave Airlie [Thu, 22 Aug 2019 03:21:16 +0000 (13:21 +1000)]
Merge branch 'etnaviv/next' of https://git.pengutronix.de/git/lst/linux into drm-next
Most importantly per-process address spaces on GPUs that are capable of
providing proper isolation has finished baking. This is the base for
our softpin implementation, which allows us to support the texture
descriptor buffers used by GC7000 series GPUs without a major UAPI
extension/rework.
Shortlog of notable changes:
- code cleanup from Fabio
- fix performance counters on GC880 and GC2000 GPUs from Christian
- drmP.h header removal from Sam
- per process address space support on MMUv2 GPUs from me
- softpin support from me
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Lucas Stach <l.stach@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/1565946875.2641.73.camel@pengutronix.de
Dave Airlie [Thu, 22 Aug 2019 03:06:50 +0000 (13:06 +1000)]
Merge tag 'du-next-
20190816' of git://linuxtv.org/pinchartl/media into drm-next
- R-Car DU fixes
- Misc. DRM cleanups
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190816133500.GJ5020@pendragon.ideasonboard.com
Dave Airlie [Wed, 21 Aug 2019 05:38:43 +0000 (15:38 +1000)]
Merge tag 'drm-misc-next-2019-08-19' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.4:
UAPI Changes:
Cross-subsystem Changes:
Core Changes:
- dma-buf: add reservation_object_fences helper, relax
reservation_object_add_shared_fence, remove
reservation_object seq number (and then
restored)
- dma-fence: Shrinkage of the dma_fence structure,
Merge dma_fence_signal and dma_fence_signal_locked,
Store the timestamp in struct dma_fence in a union with
cb_list
Driver Changes:
- More dt-bindings YAML conversions
- More removal of drmP.h includes
- dw-hdmi: Support get_eld and various i2s improvements
- gm12u320: Few fixes
- meson: Global cleanup
- panfrost: Few refactors, Support for GPU heap allocations
- sun4i: Support for DDC enable GPIO
- New panels: TI nspire, NEC NL8048HL11, LG Philips LB035Q02,
Sharp LS037V7DW01, Sony ACX565AKM, Toppoly TD028TTEC1
Toppoly TD043MTEA1
Signed-off-by: Dave Airlie <airlied@redhat.com>
[airlied: fixup dma_resv rename fallout]
From: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190819141923.7l2adietcr2pioct@flea
Nishka Dasgupta [Tue, 13 Aug 2019 06:27:11 +0000 (11:57 +0530)]
drm/xen-front: Make structure fb_funcs constant
Static structure fb_funcs, of type drm_framebuffer_funcs, is used only
when it is passed to drm_gem_fb_create_with_funcs() as its last
argument. drm_gem_fb_create_with_funcs does not modify its lst argument
(fb_funcs) and hence fb_funcs is never modified. Therefore make fb_funcs
constant to protect it from further modification.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Reviewed-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190813062712.24993-1-nishkadg.linux@gmail.com
Nishka Dasgupta [Tue, 13 Aug 2019 06:25:48 +0000 (11:55 +0530)]
drm/vboxvideo: Make structure vbox_fb_helper_funcs constant
The static structure vbox_fb_helper_funcs, of type drm_fb_helper_funcs,
is used only when it is passed as the third argument to
drm_fb_helper_fbdev_setup(), which does not modify it. Hence make it
constant to protect it from unintended modifications.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190813062548.24770-1-nishkadg.linux@gmail.com
Chris Wilson [Sat, 17 Aug 2019 15:30:22 +0000 (16:30 +0100)]
dma-fence: Store the timestamp in the same union as the cb_list
The timestamp and the cb_list are mutually exclusive, the cb_list can
only be added to prior to being signaled (and once signaled we drain),
while the timestamp is only valid upon being signaled. Both the
timestamp and the cb_list are only valid while the fence is alive, and
as soon as no references are held can be replaced by the rcu_head.
By reusing the union for the timestamp, we squeeze the base dma_fence
struct to 64 bytes on x86-64.
v2: Sort the union chronologically
Suggested-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Christian König <christian.koenig@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>.
Link: https://patchwork.freedesktop.org/patch/msgid/20190817153022.5749-1-chris@chris-wilson.co.uk
Chris Wilson [Sat, 17 Aug 2019 15:23:00 +0000 (16:23 +0100)]
dma-fence: Simply wrap dma_fence_signal_locked with dma_fence_signal
Currently dma_fence_signal() tries to avoid the spinlock and only takes
it if absolutely required to walk the callback list. However, to allow
for some users to surreptitiously insert lazy signal callbacks that
do not depend on enabling the signaling mechanism around every fence,
we always need to notify the callbacks on signaling. As such, we will
always need to take the spinlock and dma_fence_signal() effectively
becomes a clone of dma_fence_signal_locked().
v2: Update the test_and_set_bit() before entering the spinlock.
v3: Drop the test_[and_set]_bit() before the spinlock, it's a caller
error so expected to be very unlikely.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Christian König <christian.koenig@amd.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190817152300.5370-1-chris@chris-wilson.co.uk
Chris Wilson [Sat, 17 Aug 2019 14:47:34 +0000 (15:47 +0100)]
dma-fence: Avoid list_del during fence->cb_list iteration
Before we notify the fence signal callback, we remove the cb from the
list. However, since we are processing the entire list from underneath
the spinlock, we do not need to individual delete each element, but can
simply reset the link and the entire list.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Christian König <christian.koenig@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190817144736.7826-4-chris@chris-wilson.co.uk
Chris Wilson [Sat, 17 Aug 2019 14:47:33 +0000 (15:47 +0100)]
dma-fence: Shrink size of struct dma_fence
Rearrange the couple of 32-bit atomics hidden amongst the field of
pointers that unnecessarily caused the compiler to insert some padding,
shrinks the size of the base struct dma_fence from 80 to 72 bytes on
x86-64.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Christian König <christian.koenig@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190817144736.7826-3-chris@chris-wilson.co.uk
Colin Ian King [Sat, 17 Aug 2019 12:21:24 +0000 (13:21 +0100)]
drm/panel: tpo-td043mtea1: remove redundant assignment
Variable val is initialized to a value in a for-loop that is
never read and hence it is redundant. Remove it.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190817122124.29650-1-colin.king@canonical.com
Laurent Pinchart [Fri, 16 Aug 2019 12:22:28 +0000 (15:22 +0300)]
drm/omap: displays: Remove unused panel drivers
drm_panel-based drivers for the ACX565AKM, LB035Q02, LS037V7DW01,
NL8048HL11, TD028TTEC1 and TD043MTEA1 are available, remove the
omapdrm-specific drivers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190816122228.9475-3-laurent.pinchart@ideasonboard.com
Laurent Pinchart [Fri, 16 Aug 2019 12:22:27 +0000 (15:22 +0300)]
video: omapfb2: Make standard and custom panel drivers mutually exclusive
Standard DRM panel drivers for several panels used by omapfb2 are now
available. Their module name clashes with the modules from
drivers/video/fbdev/omap2/omapfb/displays, part of the deprecated omapfb2
fbdev driver. As omapfb2 can only be compiled when the omapdrm driver is
disabled, and the DRM panel drivers are useless in that case, make the
omapfb2 panels depend on the standard DRM panels being disabled to fix
the name clash.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: dc2e1e5b279966 ("drm/panel: Add driver for the Toppoly TD043MTEA1 panel")
Fixes: 415b8dd0871188 ("drm/panel: Add driver for the Toppoly TD028TTEC1 panel")
Fixes: 1c8fc3f0c5d280 ("drm/panel: Add driver for the Sony ACX565AKM panel")
Fixes: c9cf4c2a3bd35f ("drm/panel: Add driver for the Sharp LS037V7DW01 panel")
Fixes: df439abe650177 ("drm/panel: Add driver for the NEC NL8048HL11 panel")
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org> [added tags]
Link: https://patchwork.freedesktop.org/patch/msgid/20190816122228.9475-2-laurent.pinchart@ideasonboard.com
Fabrizio Castro [Fri, 2 Aug 2019 07:34:05 +0000 (08:34 +0100)]
drm: rcar-du: lvds: Fix bridge_to_rcar_lvds
Using name "bridge" for macro bridge_to_rcar_lvds argument doesn't
work when the pointer name used by the caller is not "bridge".
Rename the argument to "b" to allow for any pointer name.
While at it, fix the connector_to_rcar_lvds macro similarly.
Fixes: c6a27fa41fab ("drm: rcar-du: Convert LVDS encoder code to bridge driver")
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
[Fix connector_to_rcar_lvds]
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Laurent Pinchart [Wed, 17 Jan 2018 14:16:48 +0000 (16:16 +0200)]
drm: Remove bridge support from legacy helpers
DRM bridges are only used by atomic drivers, and none of them use the
legacy helpers. Drop bridge support from those helpers to prepare for
making the bridge operations atomic-aware.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Laurent Pinchart [Wed, 17 Jan 2018 13:54:15 +0000 (15:54 +0200)]
drm: Don't include drm/drm_encoder_slave.h when not needed
The dw-hdmi, kirin and imx drivers include the drm/drm_encoder_slave.h
header but don't use the encoder slave API. Remove it or replace it with
drm/drm_encoder.h as needed.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Wed, 14 Aug 2019 18:24:01 +0000 (19:24 +0100)]
dma-buf: Restore seqlock around dma_resv updates
This reverts
67c97fb79a7f ("dma-buf: add reservation_object_fences helper")
dd7a7d1ff2f1 ("drm/i915: use new reservation_object_fences helper")
0e1d8083bddb ("dma-buf: further relax reservation_object_add_shared_fence")
5d344f58da76 ("dma-buf: nuke reservation_object seq number")
The scenario that defeats simply grabbing a set of shared/exclusive
fences and using them blissfully under RCU is that any of those fences
may be reallocated by a SLAB_TYPESAFE_BY_RCU fence slab cache. In this
scenario, while keeping the rcu_read_lock we need to establish that no
fence was changed in the dma_resv after a read (or full) memory barrier.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190814182401.25009-1-chris@chris-wilson.co.uk
Dave Airlie [Fri, 16 Aug 2019 02:43:12 +0000 (12:43 +1000)]
Merge branch 'vmwgfx-next' of git://people.freedesktop.org/~thomash/linux into drm-next
A couple of independent patches extracted from the 5.3 pull request, fixed for
merge conflicts and a single unused variable warning.
And the drmP.h removal from Sam.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Lucas Stach [Fri, 2 Aug 2019 12:27:33 +0000 (14:27 +0200)]
drm/etnaviv: implement softpin
With softpin we allow the userspace to take control over the GPU virtual
address space. The new capability is relected by a bump of the minor DRM
version. There are a few restrictions for userspace to take into
account:
1. The kernel reserves a bit of the address space to implement zero page
faulting and mapping of the kernel internal ring buffer. Userspace can
query the kernel for the first usable GPU VM address via
ETNAVIV_PARAM_SOFTPIN_START_ADDR.
2. We only allow softpin on GPUs, which implement proper process
separation via PPAS. If softpin is not available the softpin start
address will be set to ~0.
3. Softpin is all or nothing. A submit using softpin must not use any
address fixups via relocs.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Lucas Stach [Fri, 2 Aug 2019 12:19:38 +0000 (14:19 +0200)]
drm/etnaviv: allow to request specific virtual address for gem mapping
Allow the mapping code to request a specific virtual address for the gem
mapping. If the virtual address is zero we fall back to the old mode of
allocating a virtual address for the mapping.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Lucas Stach [Fri, 2 Aug 2019 12:24:06 +0000 (14:24 +0200)]
drm/etnaviv: skip command stream validation on PPAS capable GPUs
With per-process address spaces in place, a rogue process submitting
bogus command streams can only hurt itself. There is no need to
validate the command stream before execution anymore.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Lucas Stach [Fri, 5 Jul 2019 17:17:27 +0000 (19:17 +0200)]
drm/etnaviv: implement per-process address spaces on MMUv2
This builds on top of the MMU contexts introduced earlier. Instead of having
one context per GPU core, each GPU client receives its own context.
On MMUv1 this still means a single shared pagetable set is used by all
clients, but on MMUv2 there is now a distinct set of pagetables for each
client. As the command fetch is also translated via the MMU on MMUv2 the
kernel command ringbuffer is mapped into each of the client pagetables.
As the MMU context switch is a bit of a heavy operation, due to the needed
cache and TLB flushing, this patch implements a lazy way of switching the
MMU context. The kernel does not have its own MMU context, but reuses the
last client context for all of its operations. This has some visible impact,
as the GPU can now only be started once a client has submitted some work and
we got the client MMU context assigned. Also the MMU context has a different
lifetime than the general client context, as the GPU might still execute the
kernel command buffer in the context of a client even after the client has
completed all GPU work and has been terminated. Only when the GPU is runtime
suspended or switches to another clients MMU context is the old context
freed up.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Lucas Stach [Fri, 5 Jul 2019 17:17:26 +0000 (19:17 +0200)]
drm/etnaviv: provide MMU context to etnaviv_gem_mapping_get
In preparation to having a context per process, etnaviv_gem_mapping_get
should not use the current GPU context, but needs to be told which
context to use.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Lucas Stach [Fri, 5 Jul 2019 17:17:25 +0000 (19:17 +0200)]
drm/etnaviv: split out starting of FE idle loop
Move buffer setup and starting of the FE loop in the kernel ringbuffer
into a separate function. This is a preparation to start the FE later
in the submit process.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Lucas Stach [Fri, 5 Jul 2019 17:17:24 +0000 (19:17 +0200)]
drm/etnaviv: rework MMU handling
This reworks the MMU handling to make it possible to have multiple MMU contexts.
A context is basically one instance of GPU page tables. Currently we have one
set of page tables per GPU, which isn't all that clever, as it has the
following two consequences:
1. All GPU clients (aka processes) are sharing the same pagetables, which means
there is no isolation between clients, but only between GPU assigned memory
spaces and the rest of the system. Better than nothing, but also not great.
2. Clients operating on the same set of buffers with different etnaviv GPU
cores, e.g. a workload using both the 2D and 3D GPU, need to map the used
buffers into the pagetable sets of each used GPU.
This patch reworks all the MMU handling to introduce the abstraction of the
MMU context. A context can be shared across different GPU cores, as long as
they have compatible MMU implementations, which is the case for all systems
with Vivante GPUs seen in the wild.
As MMUv1 is not able to change pagetables on the fly, without a
"stop the world" operation, which stops GPU, changes pagetables via CPU
interaction, restarts GPU, the implementation introduces a shared context on
MMUv1, which is returned whenever there is a request for a new context.
This patch assigns a MMU context to each GPU, so on MMUv2 systems there is
still one set of pagetables per GPU, but due to the shared context MMUv1
systems see a change in behavior as now a single pagetable set is used
across all GPU cores.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Lucas Stach [Fri, 5 Jul 2019 17:17:23 +0000 (19:17 +0200)]
drm/etnaviv: replace MMU flush marker with flush sequence
If a MMU is shared between multiple GPUs, all of them need to flush their
TLBs, so a single marker that gets reset on the first flush won't do.
Replace the flush marker with a sequence number, so that it's possible to
check if the TLB is in sync with the current page table state for each GPU.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Lucas Stach [Fri, 5 Jul 2019 17:17:22 +0000 (19:17 +0200)]
drm/etnaviv: share a single cmdbuf suballoc region across all GPUs
There is no need for each GPU to have it's own cmdbuf suballocation
region. Only allocate a single one for the the etnaviv virtual device
and share it across all GPUs.
As the suballoc space is now potentially shared by more hardware jobs
running in parallel, double its size to 512KB to avoid contention.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Lucas Stach [Fri, 5 Jul 2019 17:17:21 +0000 (19:17 +0200)]
drm/etnaviv: split out cmdbuf mapping into address space
This allows to decouple the cmdbuf suballocator create and mapping
the region into the GPU address space. Allowing multiple AS to share
a single cmdbuf suballoc.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Lucas Stach [Fri, 5 Jul 2019 17:17:20 +0000 (19:17 +0200)]
drm/etnaviv: simplify unbind checks
Remember if the GPU has been sucessfully initialized. Only in that case
do we need to clean up various structures in the unbind path. If the
GPU hasn't been sucessfully initialized all the cleanups should happen
in the failure paths of the init function.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Lucas Stach [Fri, 9 Aug 2019 11:59:25 +0000 (13:59 +0200)]
drm/etnaviv: pass mmu pointer to etnaviv_core_dump_mmu
This function does only need the mmu part part of the gpu struct.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Lucas Stach [Fri, 9 Aug 2019 11:58:02 +0000 (13:58 +0200)]
drm/etnaviv: dump only failing submit
Due to the tracking provided by the scheduler we know exactly which
submit is failing. Only dump this single submit and the required
auxiliary information. This cuts down the size of the devcoredumps
by only including relevant information.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Thomas Hellstrom [Mon, 4 Mar 2019 18:37:40 +0000 (19:37 +0100)]
drm/vmwgfx: Assign eviction priorities to resources
TTM provides a means to assign eviction priorities to buffer object. This
means that all buffer objects with a lower priority will be evicted first
on memory pressure.
Use this to make sure surfaces and in particular non-dirty surfaces are
evicted first. Evicting in particular shaders, cotables and contexts imply
a significant performance hit on vmwgfx, so make sure these resources are
evicted last.
Some buffer objects are sub-allocated in user-space which means we can have
many resources attached to a single buffer object or resource. In that case
the buffer object is given the highest priority of the attached resources.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
Sam Ravnborg [Sun, 23 Jun 2019 10:23:34 +0000 (12:23 +0200)]
drm/vmwgfx: drop reminaing users of drmP.h
Drop use of the deprecated drmP.h file from the
remaining files.
In several cases the drmP.h include could be removed without
furter fixes. Other files required a few header files to be added.
In all files divided includes files in blocks and sort them.
v2:
- fix warning in i386 build wiht HIGHMEM disabled
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reported-by: kbuild test robot <lkp@intel.com> [warning in i386 build]
Cc: VMware Graphics <linux-graphics-maintainer@vmware.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Sam Ravnborg [Sun, 23 Jun 2019 10:23:33 +0000 (12:23 +0200)]
drm/vmwgfx: drop use of drmP.h in header files
To facilitate removal of drmP.h in the .c
files remove the use from header files first.
Fix fallout in the other files.
Sorted include files in blocks and sorted files
within each block in alphabetical order.
This revealed a dependency from an uapi header to a header
located below drivers/gpu/drm/vmwgfx/.
Added FIXME to remind someone to fix this.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: VMware Graphics <linux-graphics-maintainer@vmware.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Thomas Hellstrom [Tue, 28 May 2019 06:08:55 +0000 (08:08 +0200)]
drm/vmwgfx: Kill unneeded legacy security features
At one point, the GPU command verifier and user-space handle manager
couldn't properly protect GPU clients from accessing each other's data.
Instead there was an elaborate mechanism to make sure only the active
master's primary clients could render. The other clients were either
put to sleep or even killed (if the master had exited). VRAM was
evicted on master switch. With the advent of render-node functionality,
we relaxed the VRAM eviction, but the other mechanisms stayed in place.
Now that the GPU command verifier and ttm object manager properly
isolates primary clients from different master realms we can remove the
master switch related code and drop those legacy features.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
Laurent Pinchart [Tue, 13 Aug 2019 20:11:01 +0000 (23:11 +0300)]
drm/panel: Add driver for the Toppoly TD043MTEA1 panel
This panel is used on the OMAP3 Pandora.
The code is based on the omapdrm-specific panel-tpo-td043mtea1 driver.
v2:
- fix checkpatch warnings
o (lcd == NULL) => (!lcd) (sam)
o alignment to open '(' (sam)
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190813201101.30980-10-laurent.pinchart@ideasonboard.com
Laurent Pinchart [Tue, 13 Aug 2019 20:11:00 +0000 (23:11 +0300)]
drm/panel: Add driver for the Toppoly TD028TTEC1 panel
This panel is used on the OpenMoko Neo FreeRunner and Neo 1973.
The code is based on the omapdrm-specific panel-tpo-td028ttec1 driver.
v2:
- fix checkpatch warnings:
o (lcd == NULL) => (!lcd) (sam)
o (1 << X) => BIT(X) (sam)
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190813201101.30980-9-laurent.pinchart@ideasonboard.com
Laurent Pinchart [Tue, 13 Aug 2019 20:10:59 +0000 (23:10 +0300)]
drm/panel: Add driver for the Sony ACX565AKM panel
This panel is used on the Nokia N900.
The code is based on the omapdrm-specific panel-sony-acx565akm driver.
The hardware-related logic has been changed as little as possible to
avoid regressions as hardware availability is lacking to test the
changes. Follow-up patches should address the items listed in the TODO
list.
v2:
- fix checkpatch warning (lcd == NULL) => (!lcd) (sam)
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190813201101.30980-8-laurent.pinchart@ideasonboard.com
Laurent Pinchart [Tue, 13 Aug 2019 20:10:58 +0000 (23:10 +0300)]
drm/panel: Add driver for the Sharp LS037V7DW01 panel
This panel is used on the TI SDP3430 board.
The code is based on the omapdrm-specific panel-sharp-ls037v7dw01
driver.
v2:
- fix checkpatch warning (lcd == NULL) => (!lcd) (sam)
- drop __exit_p() from remove. It caused a build warning.
And no other panel drivers needs this (sam)
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190813201101.30980-7-laurent.pinchart@ideasonboard.com
Laurent Pinchart [Tue, 13 Aug 2019 20:10:57 +0000 (23:10 +0300)]
drm/panel: Add driver for the NEC NL8048HL11 panel
This panel is used on the Zoom2/3/3630 SDP boards.
The code is based on the omapdrm-specific panel-nec-nl8048hl11 driver
v2:
- fix checkpatch warning (lcd == NULL) => (!lcd) (sam)
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190813201101.30980-6-laurent.pinchart@ideasonboard.com
Laurent Pinchart [Tue, 13 Aug 2019 20:10:56 +0000 (23:10 +0300)]
drm/panel: Add driver for the LG Philips LB035Q02 panel
This panel is used on the Gumstix Overo Palo35.
The code is based on the omapdrm-specific panel-lgphilips-lb035q02
driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190813201101.30980-5-laurent.pinchart@ideasonboard.com
Laurent Pinchart [Tue, 13 Aug 2019 20:10:55 +0000 (23:10 +0300)]
dt-bindings: display: panel: Add bindings for NEC NL8048HL11 panel
The NEC NL8048HL11 is a 10.4cm WVGA (800x480) panel with a 24-bit RGB
parallel data interface and an SPI control interface.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190813201101.30980-4-laurent.pinchart@ideasonboard.com
Laurent Pinchart [Tue, 13 Aug 2019 20:10:54 +0000 (23:10 +0300)]
dt-bindings: Add legacy 'toppoly' vendor prefix
The 'toppoly' vendor prefix is in use and refers to TPO, whose DT vendor
prefix is already defined as 'tpo'. Add 'toppoly' as an alternative and
document it as legacy.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190813201101.30980-3-laurent.pinchart@ideasonboard.com
Laurent Pinchart [Tue, 13 Aug 2019 20:10:53 +0000 (23:10 +0300)]
dt-bindings: Add vendor prefix for LG Display
LG Display is an LCD display manufacturer. Originally formed as a joint
venture by LG Electronics and Philips Electronics, it was formerly known
as LG.Philips LCD, hence the DT vendor prefix lgphilips (which is
already in active use in the kernel).
More information is available at
https://en.wikipedia.org/wiki/LG_Display.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190813201101.30980-2-laurent.pinchart@ideasonboard.com
Nishka Dasgupta [Tue, 13 Aug 2019 06:33:55 +0000 (12:03 +0530)]
drm/aspeed: gfc_crtc: Make structure aspeed_gfx_funcs constant
The static structure aspeed_gfx_funcs, of type
drm_simple_display_pipe_funcs, is used only as an argument to
drm_simple_display_pipe_init(), which does not modify it. Hence make it
constant to protect it from unintended modification.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190813063355.25549-1-nishkadg.linux@gmail.com
Sam Ravnborg [Sun, 4 Aug 2019 09:41:32 +0000 (11:41 +0200)]
drm/arm: drop use of drmP.h
Drop use of the deprecated drmP.h header file.
While touching the list of include files divide them
into blocks and sort within each block.
Fix fallout.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Brian Starkey <brian.starkey@arm.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: malidp@foss.arm.com
Link: https://patchwork.freedesktop.org/patch/msgid/20190804094132.29463-5-sam@ravnborg.org
Sam Ravnborg [Sun, 4 Aug 2019 09:41:31 +0000 (11:41 +0200)]
drm/armada: drop use of drmP.h
Drop use of the deprecated drmP.h header file.
While touching the list of include files group them and sort them.
Fix fallout from the header file removal.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190804094132.29463-4-sam@ravnborg.org
Sam Ravnborg [Sun, 4 Aug 2019 09:41:30 +0000 (11:41 +0200)]
drm/tegra: drop use of drmP.h
Drop use of the deprecated drmP.h header file.
For all touched files divide include files into blocks,
and sort them within the blocks.
Fix fallout.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20190804094132.29463-3-sam@ravnborg.org
Sam Ravnborg [Sun, 4 Aug 2019 09:41:29 +0000 (11:41 +0200)]
drm/i2c/tda998x: drop use of drmP.h
Drop use of the deprecated drmP.h header file.
Fix fallout.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190804094132.29463-2-sam@ravnborg.org
Geert Uytterhoeven [Tue, 13 Aug 2019 09:30:46 +0000 (11:30 +0200)]
drm/bridge: dumb-vga-dac: Fix dereferencing -ENODEV DDC channel
If the VGA connector has no DDC channel, an error pointer will be
dereferenced, e.g. on Salvator-XS:
Unable to handle kernel NULL pointer dereference at virtual address
000000000000017d
...
Call trace:
sysfs_do_create_link_sd.isra.0+0x40/0x108
sysfs_create_link+0x20/0x40
drm_sysfs_connector_add+0xa8/0xc8
drm_connector_register.part.3+0x54/0xb0
drm_connector_register_all+0xb0/0xd0
drm_modeset_register_all+0x54/0x88
drm_dev_register+0x18c/0x1d8
rcar_du_probe+0xe4/0x150
...
This happens because vga->ddc either contains a valid DDC channel
pointer, or -ENODEV, and drm_connector_init_with_ddc() expects a valid
DDC channel pointer, or NULL.
Fix this by resetting vga->ddc to NULL in case of -ENODEV, and replacing
the existing error checks by non-NULL checks.
This is similar to what the HDMI connector driver does.
Fixes: a4f9087e85de141e ("drm/bridge: dumb-vga-dac: Provide ddc symlink in connector sysfs directory")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190813093046.4976-1-geert+renesas@glider.be
Jerome Brunet [Mon, 12 Aug 2019 12:50:16 +0000 (14:50 +0200)]
drm/bridge: dw-hdmi-i2s: add .get_eld support
Provide the eld to the generic hdmi-codec driver.
This will let the driver enforce the maximum channel number and set the
channel allocation depending on the hdmi sink.
Cc: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190812125016.20169-1-jbrunet@baylibre.com
Jerome Brunet [Mon, 12 Aug 2019 12:07:25 +0000 (14:07 +0200)]
drm/bridge: dw-hdmi-i2s: enable only the required i2s lanes
Enable the i2s lanes depending on the number of channel in the stream
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190812120726.1528-8-jbrunet@baylibre.com
Jerome Brunet [Mon, 12 Aug 2019 12:07:24 +0000 (14:07 +0200)]
drm/bridge: dw-hdmi-i2s: reset audio fifo before applying new params
When changing the audio hw params, reset the audio fifo to make sure
any old remaining data is flushed.
The databook mentions that such reset should be followed by a reset of
the i2s block to make sure the samples stay aligned
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190812120726.1528-7-jbrunet@baylibre.com
Jerome Brunet [Mon, 12 Aug 2019 12:07:23 +0000 (14:07 +0200)]
drm/bridge: dw-hdmi-i2s: set the channel allocation
setup the channel allocation provided by the generic hdmi-codec driver
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190812120726.1528-6-jbrunet@baylibre.com
Jerome Brunet [Mon, 12 Aug 2019 12:07:22 +0000 (14:07 +0200)]
drm/bridge: dw-hdmi-i2s: enable lpcm multi channels
Properly setup the channel count and layout in dw-hdmi i2s driver so
we are not limited to 2 channels.
Also correct the maximum channel reported by the DAI from 6 to 8 ch
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190812120726.1528-5-jbrunet@baylibre.com
Jerome Brunet [Mon, 12 Aug 2019 12:07:21 +0000 (14:07 +0200)]
drm/bridge: dw-hdmi: set channel count in the infoframes
Set the number of channel in the infoframes
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190812120726.1528-4-jbrunet@baylibre.com
Jerome Brunet [Mon, 12 Aug 2019 12:07:20 +0000 (14:07 +0200)]
drm/bridge: dw-hdmi: move audio channel setup out of ahb
Part of the channel count setup done in dw-hdmi ahb should
actually be done whatever the interface providing the data.
Let's move it to dw-hdmi driver instead.
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190812120726.1528-3-jbrunet@baylibre.com
Jerome Brunet [Mon, 12 Aug 2019 12:07:19 +0000 (14:07 +0200)]
drm/bridge: dw-hdmi-i2s: support more i2s format
The dw-hdmi-i2s supports more formats than just regular i2s.
Add support for left justified, right justified and dsp modes
A and B.
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190812120726.1528-2-jbrunet@baylibre.com
Neil Armstrong [Thu, 8 Aug 2019 08:55:22 +0000 (10:55 +0200)]
MAINTAINERS: Update with Amlogic DRM bindings converted as YAML
The amlogic,meson-dw-hdmi.txt and amlogic,meson-vpu.txt has been
converted to YAML schemas, update MAINTAINERS to match them again.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Maxime Jourdan <mjourdan@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190808085522.21950-4-narmstrong@baylibre.com
Neil Armstrong [Thu, 8 Aug 2019 08:55:21 +0000 (10:55 +0200)]
dt-bindings: display: amlogic, meson-vpu: convert to yaml
Now that we have the DT validation in place, let's convert the device tree
bindings for the Amlogic Display Controller over to YAML schemas.
The original example has a leftover "dmc" memory cell, that has been
removed in the yaml rewrite.
The port connection table has been dropped in favor of a description
of each port.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190808085522.21950-3-narmstrong@baylibre.com
Neil Armstrong [Thu, 8 Aug 2019 08:55:20 +0000 (10:55 +0200)]
dt-bindings: display: amlogic, meson-dw-hdmi: convert to yaml
Now that we have the DT validation in place, let's convert the device tree
bindings for the Amlogic Synopsys DW-HDMI specifics over to YAML schemas.
The original example and usage of clock-names uses a reversed "isfr"
and "iahb" clock-names, the rewritten YAML bindings uses the reversed
instead of fixing the device trees order.
The #sound-dai-cells optional property has been added to match this node
as a sound dai.
The port connection table has been dropped in favor of a description
of each port.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190808085522.21950-2-narmstrong@baylibre.com
Deepak Rawat [Thu, 9 May 2019 19:42:58 +0000 (12:42 -0700)]
drm/vmwgfx: Use VMW_DEBUG_KMS for vmwgfx mode-setting user errors
For errors during layout change ioctl use VMW_DEBUG_KMS instead of
DRM_ERROR.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
projects / openwrt / staging / blogic.git / log