Pascal van Leeuwen [Tue, 17 Sep 2019 10:07:59 +0000 (12:07 +0200)]
crypto: inside-secure - Added support for the rfc4106(gcm(aes)) AEAD
This patch adds support for rfc4106(gcm(aes)) for use with IPsec ESP
Signed-off-by: Pascal van Leeuwen <pvanleeuwen@verimatrix.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pascal van Leeuwen [Tue, 17 Sep 2019 09:55:19 +0000 (11:55 +0200)]
crypto: inside-secure - Fixed corner case TRC admin RAM probing issue
This patch fixed a corner case admin RAM probing issue witnessed on the
Xilinx VCU118 FPGA development board with an EIP197 configuration with
4096 words of admin RAM, of which only 2050 were recognised.
Signed-off-by: Pascal van Leeuwen <pvanleeuwen@verimatrix.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pascal van Leeuwen [Tue, 17 Sep 2019 09:55:18 +0000 (11:55 +0200)]
crypto: inside-secure - Fix stability issue with Macchiatobin
This patch corrects an error in the Transform Record Cache initialization
code that was causing intermittent stability problems on the Macchiatobin
board.
Unfortunately, due to HW platform specifics, the problem could not happen
on the main development platform, being the VCU118 Xilinx development
board. And since it was a problem with hash table access, it was very
dependent on the actual physical context record DMA buffers being used,
i.e. with some (bad) luck it could seemingly work quit stable for a while.
Signed-off-by: Pascal van Leeuwen <pvanleeuwen@verimatrix.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Nagadheeraj Rottela [Tue, 17 Sep 2019 06:36:50 +0000 (06:36 +0000)]
crypto: cavium/nitrox - Fix cbc ciphers self test failures
Self test failures are due to wrong output IV. This patch fixes this
issue by copying back output IV into skcipher request.
Signed-off-by: Nagadheeraj Rottela <rnagadheeraj@marvell.com>
Reviewed-by: Srikanth Jampala <jsrikanth@marvell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Nagadheeraj Rottela [Mon, 16 Sep 2019 06:42:06 +0000 (06:42 +0000)]
crypto: cavium/nitrox - check assoclen and authsize for gcm(aes) cipher
Check if device supports assoclen to solve hung task timeout error when
extra tests are enabled. Return -EINVAL if assoclen is not supported.
Check authsize to return -EINVAL if authentication tag size is invalid.
Change blocksize to 1 to match with generic implementation.
Signed-off-by: Nagadheeraj Rottela <rnagadheeraj@marvell.com>
Reported-by: Mallesham Jatharakonda <mallesham.jatharakonda@oneconvergence.com>
Suggested-by: Mallesham Jatharakonda <mallesham.jatharakonda@oneconvergence.com>
Reviewed-by: Srikanth Jampala <jsrikanth@marvell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tony Lindgren [Sat, 14 Sep 2019 21:03:00 +0000 (14:03 -0700)]
hwrng: omap3-rom - Use devm hwrng and runtime PM
This allows us to simplify things more for probe and exit.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Adam Ford <aford173@gmail.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Suggested-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tony Lindgren [Sat, 14 Sep 2019 21:02:59 +0000 (14:02 -0700)]
hwrng: omap3-rom - Use runtime PM instead of custom functions
Nowadays we have runtime PM, and we can use it with autosuspend_timeout
to idle things automatically. This allows us to get rid of the custom
PM implementation.
We enable clocks and init RNG in runtime_resume, and reset RNG and
disable clocks in runtime_suspend. And then omap3_rom_rng_read()
becomes very simple and we don't need the old functions for
omap3_rom_rng_idle() and omap3_rom_rng_get_random(). We can now also
get rid of pr_fmt as we're using dev_err instead.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Adam Ford <aford173@gmail.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tony Lindgren [Sat, 14 Sep 2019 21:02:58 +0000 (14:02 -0700)]
hwrng: omap3-rom - Update to use standard driver data
Let's update omap3-rom-rng to use standard driver data to make it easier
to add runtime PM support in the following patch. Just use it for the
rng ops and clock for now. Let's still keep also old rng_clk still around,
we will remove delayed work and rng_clk with runtime PM in the next patch.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Adam Ford <aford173@gmail.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tony Lindgren [Sat, 14 Sep 2019 21:02:57 +0000 (14:02 -0700)]
hwrng: omap3-rom - Initialize default quality to get data
Similar to commit
62f95ae805fa ("hwrng: omap - Set default quality")
we need to initialize the default quality for the RNG to be used.
The symptoms of this problem is that doing hd /dev/random does not
produce much data at all.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Adam Ford <aford173@gmail.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tony Lindgren [Sat, 14 Sep 2019 21:02:56 +0000 (14:02 -0700)]
hwrng: omap3-rom - Call clk_disable_unprepare() on exit only if not idled
When unloading omap3-rom-rng, we'll get the following:
WARNING: CPU: 0 PID: 100 at drivers/clk/clk.c:948 clk_core_disable
This is because the clock may be already disabled by omap3_rom_rng_idle().
Let's fix the issue by checking for rng_idle on exit.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Adam Ford <aford173@gmail.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Fixes: 1c6b7c2108bd ("hwrng: OMAP3 ROM Random Number Generator support")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tony Lindgren [Sat, 14 Sep 2019 21:02:55 +0000 (14:02 -0700)]
hwrng: omap3-rom - Fix missing clock by probing with device tree
Commit
0ed266d7ae5e ("clk: ti: omap3: cleanup unnecessary clock aliases")
removed old omap3 clock framework aliases but caused omap3-rom-rng to
stop working with clock not found error.
Based on discussions on the mailing list it was requested by Tero Kristo
that it would be best to fix this issue by probing omap3-rom-rng using
device tree to provide a proper clk property. The other option would be
to add back the missing clock alias, but that does not help moving things
forward with removing old legacy platform_data.
Let's also add a proper device tree binding and keep it together with
the fix.
Cc: devicetree@vger.kernel.org
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Adam Ford <aford173@gmail.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Fixes: 0ed266d7ae5e ("clk: ti: omap3: cleanup unnecessary clock aliases")
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tony Lindgren [Sat, 14 Sep 2019 21:02:54 +0000 (14:02 -0700)]
ARM: OMAP2+: Check omap3-rom-rng for GP device instead of HS device
In general we should check for GP device instead of HS device unless
the other options such as EMU are also checked. Otherwise omap3-rom-rng
won't probe on few of the old n900 macro boards still in service in
automated build and boot test systems.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Adam Ford <aford173@gmail.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pascal van Leeuwen [Fri, 13 Sep 2019 20:04:46 +0000 (22:04 +0200)]
crypto: inside-secure - Added support for authenc HMAC-SHA2/DES-CBC
This patch adds support for the authenc(hmac(sha224),cbc(des)),
authenc(hmac(sha256),cbc(des)), authenc(hmac(sha384),cbc(des))
and authenc(hmac(sha512),cbc(des)) aead's
changes since v1:
- nothing
Signed-off-by: Pascal van Leeuwen <pvanleeuwen@verimatrix.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pascal van Leeuwen [Fri, 13 Sep 2019 20:04:45 +0000 (22:04 +0200)]
crypto: inside-secure - Added support for authenc HMAC-SHA2/3DES-CBC
This patch adds support for the authenc(hmac(sha224),cbc(des3_ede)),
authenc(hmac(sha256),cbc(des3_ede)), authenc(hmac(sha384),cbc(des3_ede))
and authenc(hmac(sha512),cbc(des3_ede)) aead's
changes since v1:
- nothing
Signed-off-by: Pascal van Leeuwen <pvanleeuwen@verimatrix.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pascal van Leeuwen [Fri, 13 Sep 2019 20:04:44 +0000 (22:04 +0200)]
crypto: inside-secure - Added support for authenc HMAC-SHA1/DES-CBC
This patch adds support for the authenc(hmac(sha1),cbc(des)) aead
changes since v1:
- rebased on top of DES changes made to cryptodev/master
Signed-off-by: Pascal van Leeuwen <pvanleeuwen@verimatrix.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pascal van Leeuwen [Fri, 13 Sep 2019 18:56:49 +0000 (20:56 +0200)]
crypto: inside-secure - Add CRYPTO_SHA3 to CRYPTO_DEV_SAFEXCEL
Due to the addition of SHA3 and HMAC-SHA3 support to the inside-secure
driver, it now depends on CRYPTO_SHA3. Added reference.
changes since v1:
- added missing dependency to crypto/Kconfig
Signed-off-by: Pascal van Leeuwen <pvanleeuwen@verimatrix.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pascal van Leeuwen [Fri, 13 Sep 2019 18:56:48 +0000 (20:56 +0200)]
crypto: inside-secure - Add HMAC-SHA3 family of authentication algorithms
This patch adds support for hmac(sha3-224), hmac(sha3-256), hmac(sha3-384)
and hmac(sha3-512) authentication algorithms.
The patch has been tested with the eip197c_iewxkbc configuration on the
Xilinx VCU118 development board, including the testmgr extra tests.
changes since v1:
- nothing
Signed-off-by: Pascal van Leeuwen <pvanleeuwen@verimatrix.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pascal van Leeuwen [Fri, 13 Sep 2019 18:56:47 +0000 (20:56 +0200)]
crypto: inside-secure - Add SHA3 family of basic hash algorithms
This patch adds support for sha3-224, sha3-256, sha3-384 and sha3-512
basic hashes.
The patch has been tested with the eip197c_iewxkbc configuration on the
Xilinx VCU118 development board, including the testmgr extra tests.
changes since v1:
- nothing
Signed-off-by: Pascal van Leeuwen <pvanleeuwen@verimatrix.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pascal van Leeuwen [Fri, 13 Sep 2019 18:44:50 +0000 (20:44 +0200)]
crypto: inside-secure - Add SM4 based authenc AEAD ciphersuites
This patch adds support for the authenc(hmac(sha1),cbc(sm4)),
authenc(hmac(sm3),cbc(sm4)), authenc(hmac(sha1),rfc3686(ctr(sm4))),
and authenc(hmac(sm3),rfc3686(ctr(sm4))) aead ciphersuites.
These are necessary to support IPsec according to the Chinese standard
GM/T 022-1014 - IPsec VPN specification.
Note that there are no testvectors present in testmgr for these
ciphersuites. However, considering all building blocks have already been
verified elsewhere, it is fair to assume the generic implementation to be
correct-by-construction.
The hardware implementation has been fuzzed against this generic
implementation by means of a locally modified testmgr. The intention is
to upstream these testmgr changes but this is pending other testmgr changes
being made by Eric Biggers.
The patch has been tested with the eip197c_iewxkbc configuration on the
Xilinx VCU118 development board, using the abovementioned modified testmgr
This patch applies on top of "Add support for SM4 ciphers" and needs to
be applied before "Add (HMAC) SHA3 support".
Signed-off-by: Pascal van Leeuwen <pvanleeuwen@verimatrix.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Ard Biesheuvel [Fri, 13 Sep 2019 18:36:18 +0000 (19:36 +0100)]
crypto: aegis128-neon - use Clang compatible cflags for ARM
The next version of Clang will start policing compiler command line
options, and will reject combinations of -march and -mfpu that it
thinks are incompatible.
This results in errors like
clang-10: warning: ignoring extension 'crypto' because the 'armv7-a'
architecture does not support it [-Winvalid-command-line-argument]
/tmp/aegis128-neon-inner-5ee428.s: Assembler messages:
/tmp/aegis128-neon-inner-5ee428.s:73: Error: selected
processor does not support `aese.8 q2,q14' in ARM mode
when buiding the SIMD aegis128 code for 32-bit ARM, given that the
'armv7-a' -march argument is considered to be compatible with the
ARM crypto extensions. Instead, we should use armv8-a, which does
allow the crypto extensions to be enabled.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pascal van Leeuwen [Fri, 13 Sep 2019 09:10:42 +0000 (11:10 +0200)]
crypto: testmgr - Added testvectors for the rfc3686(ctr(sm4)) skcipher
Added testvectors for the rfc3686(ctr(sm4)) skcipher algorithm
changes since v1:
- nothing
Signed-off-by: Pascal van Leeuwen <pvanleeuwen@verimatrix.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pascal van Leeuwen [Fri, 13 Sep 2019 09:10:41 +0000 (11:10 +0200)]
crypto: inside-secure - Add support for the rfc3685(ctr(sm4)) skcipher
This patch adds support for SM4 in (32 bit) CTR mode, i.e. skcipher
rfc3686(ctr(sm4)).
changes since v1:
- nothing
Signed-off-by: Pascal van Leeuwen <pvanleeuwen@verimatrix.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pascal van Leeuwen [Fri, 13 Sep 2019 09:10:40 +0000 (11:10 +0200)]
crypto: inside-secure - Add support for the cfb(sm4) skcipher
This patch adds support for SM4 in CFB mode, i.e. skcipher cfb(sm4).
changes since v1:
- nothing
Signed-off-by: Pascal van Leeuwen <pvanleeuwen@verimatrix.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pascal van Leeuwen [Fri, 13 Sep 2019 09:10:39 +0000 (11:10 +0200)]
crypto: testmgr - Added testvectors for the ofb(sm4) & cfb(sm4) skciphers
Added testvectors for the ofb(sm4) and cfb(sm4) skcipher algorithms
changes since v1:
- nothing
Signed-off-by: Pascal van Leeuwen <pvanleeuwen@verimatrix.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pascal van Leeuwen [Fri, 13 Sep 2019 09:10:38 +0000 (11:10 +0200)]
crypto: inside-secure - Add support for the ofb(sm4) skcipher
This patch adds support for SM4 in OFB mode, i.e. skcipher ofb(sm4).
changes since v1:
- nothing
Signed-off-by: Pascal van Leeuwen <pvanleeuwen@verimatrix.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pascal van Leeuwen [Fri, 13 Sep 2019 09:10:37 +0000 (11:10 +0200)]
crypto: inside-secure - Add support for the cbc(sm4) skcipher
This patch adds support for SM4 in CBC mode, i.e. skcipher cbc(sm4).
changes since v1:
- nothing
Signed-off-by: Pascal van Leeuwen <pvanleeuwen@verimatrix.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pascal van Leeuwen [Fri, 13 Sep 2019 09:10:36 +0000 (11:10 +0200)]
crypto: inside-secure - Add support for the ecb(sm4) skcipher
This patch adds support for SM4 in ECB mode, i.e. skcipher ecb(sm4).
changes since v1:
- make SAFEXCEL_SM4 case entry explit, using the proper SM4_BLOCK_SIZE
instead of "borrowing" the AES code which "coincidentally" works
Signed-off-by: Pascal van Leeuwen <pvanleeuwen@verimatrix.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pascal van Leeuwen [Fri, 13 Sep 2019 15:20:38 +0000 (17:20 +0200)]
crypto: testmgr - Added testvectors for the hmac(sm3) ahash
Added testvectors for the hmac(sm3) ahash authentication algorithm
changes since v1 & v2:
-nothing
Signed-off-by: Pascal van Leeuwen <pvanleeuwen@verimatrix.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pascal van Leeuwen [Fri, 13 Sep 2019 15:20:37 +0000 (17:20 +0200)]
crypto: inside-secure - Added support for HMAC-SM3 ahash
Added support for the hmac(sm3) ahash authentication algorithm
changes since v1:
- added Acked-by tag below, no changes to the source
changes since v2:
- nothing
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Pascal van Leeuwen <pvanleeuwen@verimatrix.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pascal van Leeuwen [Fri, 13 Sep 2019 15:20:36 +0000 (17:20 +0200)]
crypto: inside-secure - Added support for basic SM3 ahash
Added support for the SM3 ahash algorithm
changes since v1:
- moved definition of CONTEXT_CONTROL_CRYPTO_ALG_SM3 (0x7) up above 0xf
changes since v2:
- allow compilation if CONFIG_CRYPTO_SM3 is not set
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Pascal van Leeuwen <pvanleeuwen@verimatrix.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pascal van Leeuwen [Wed, 18 Sep 2019 21:25:58 +0000 (23:25 +0200)]
crypto: inside-secure - Add CRYPTO_CHACHA20POLY1305 to CRYPTO_DEV_SAFEXCEL
Due to the addition of Chacha20-Poly1305 support to the inside-secure
driver, it now depends on CRYPTO_CHACHA20POLY1305. Added reference.
changes since v1:
- added missing dependency to crypto/Kconfig
changes since v2:
- nothing
changes since v3:
- nothing
Signed-off-by: Pascal van Leeuwen <pvanleeuwen@verimatrix.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pascal van Leeuwen [Wed, 18 Sep 2019 21:25:57 +0000 (23:25 +0200)]
crypto: inside-secure - Add support for the Chacha20-Poly1305 AEAD
This patch adds support for the Chacha20-Poly1305 cipher suite.
It adds both the basic rfc7539(chacha20,poly1305) as well as the
rfc7539esp(chacha20,poly1305) variant for IPsec ESP acceleration.
changes since v1:
- rebased on top of DES library changes done on cryptodev/master
- fixed crypto/Kconfig so that generic fallback is compiled as well
changes since v2:
- nothing
changes since v3:
- Fixed a problem where the tcrypt performance test would run fully on the
fallback cipher instead of the HW due to using an AAD length of 8 for
rfc7539esp. While this is not actually legal ESP (which includes SPI and
sequence number in the AAD as well), it is both inconvenient and not
necessary to run these vectors on the fallback cipher.
- Due to above, also realised that for plain (non-ESP) rfc7539, you
probably want to be able to run vectors with less than 8 bytes of AAD
on the HW, and this is actually possible as long as cryptlen is large
enough, so made that possible as well.
Signed-off-by: Pascal van Leeuwen <pvanleeuwen@verimatrix.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pascal van Leeuwen [Wed, 18 Sep 2019 21:25:56 +0000 (23:25 +0200)]
crypto: inside-secure - Added support for the CHACHA20 skcipher
Added support for the CHACHA20 skcipher algorithm.
Tested on an eip197c-iesb configuration in the Xilinx VCU118 devboard,
passes all testmgr vectors plus the extra fuzzing tests.
changes since v1:
- rebased on top of DES library changes done on cryptodev/master
- fixed crypto/Kconfig so that generic fallback is compiled as well
changes since v2:
- made switch entry SAFEXCEL_AES explit and added empty default, as
requested by Antoine Tenart. Also needed to make SM4 patches apply.
changes since v3:
- nothing
Signed-off-by: Pascal van Leeuwen <pvanleeuwen@verimatrix.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tomer Maimon [Thu, 12 Sep 2019 09:01:49 +0000 (12:01 +0300)]
hwrng: npcm - add NPCM RNG driver
Add Nuvoton NPCM BMC Random Number Generator(RNG) driver.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tomer Maimon [Thu, 12 Sep 2019 09:01:48 +0000 (12:01 +0300)]
dt-binding: hwrng: add NPCM RNG documentation
Added device tree binding documentation for Nuvoton BMC
NPCM Random Number Generator (RNG).
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Ard Biesheuvel [Tue, 10 Sep 2019 23:19:00 +0000 (00:19 +0100)]
crypto: arm64/gcm-ce - implement 4 way interleave
To improve performance on cores with deep pipelines such as ThunderX2,
reimplement gcm(aes) using a 4-way interleave rather than the 2-way
interleave we use currently.
This comes down to a complete rewrite of the GCM part of the combined
GCM/GHASH driver, and instead of interleaving two invocations of AES
with the GHASH handling at the instruction level, the new version
uses a more coarse grained approach where each chunk of 64 bytes is
encrypted first and then ghashed (or ghashed and then decrypted in
the converse case).
The core NEON routine is now able to consume inputs of any size,
and tail blocks of less than 64 bytes are handled using overlapping
loads and stores, and processed by the same 4-way encryption and
hashing routines. This gets rid of most of the branches, and avoids
having to return to the C code to handle the tail block using a
stack buffer.
The table below compares the performance of the old driver and the new
one on various micro-architectures and running in various modes.
| AES-128 | AES-192 | AES-256 |
#bytes | 512 | 1500 | 4k | 512 | 1500 | 4k | 512 | 1500 | 4k |
-------+-----+------+-----+-----+------+-----+-----+------+-----+
TX2 | 35% | 23% | 11% | 34% | 20% | 9% | 38% | 25% | 16% |
EMAG | 11% | 6% | 3% | 12% | 4% | 2% | 11% | 4% | 2% |
A72 | 8% | 5% | -4% | 9% | 4% | -5% | 7% | 4% | -5% |
A53 | 11% | 6% | -1% | 10% | 8% | -1% | 10% | 8% | -2% |
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Ard Biesheuvel [Tue, 10 Sep 2019 23:18:59 +0000 (00:18 +0100)]
crypto: testmgr - add another gcm(aes) testcase
Add an additional gcm(aes) test case that triggers the code path in
the new arm64 driver that deals with tail blocks whose size is not
a multiple of the block size, and where the size of the preceding
input is a multiple of 64 bytes.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Christophe Leroy [Tue, 10 Sep 2019 06:04:14 +0000 (06:04 +0000)]
crypto: talitos - fix hash result for VMAP_STACK
When VMAP_STACK is selected, stack cannot be DMA-mapped.
Therefore, the hash result has to be DMA-mapped in the request
context and copied into areq->result at completion.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Herbert Xu [Tue, 10 Sep 2019 01:42:05 +0000 (11:42 +1000)]
crypto: algif_skcipher - Use chunksize instead of blocksize
When algif_skcipher does a partial operation it always process data
that is a multiple of blocksize. However, for algorithms such as
CTR this is wrong because even though it can process any number of
bytes overall, the partial block must come at the very end and not
in the middle.
This is exactly what chunksize is meant to describe so this patch
changes blocksize to chunksize.
Fixes: 8ff590903d5f ("crypto: algif_skcipher - User-space...")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pascal van Leeuwen [Mon, 9 Sep 2019 11:13:08 +0000 (13:13 +0200)]
crypto: inside-secure - Added support for the AES-CMAC ahash
This patch adds support for the AES-CMAC authentication algorithm.
Signed-off-by: Pascal van Leeuwen <pvanleeuwen@verimatrix.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pascal van Leeuwen [Mon, 9 Sep 2019 11:13:07 +0000 (13:13 +0200)]
crypto: inside-secure - Added support for the AES XCBC ahash
This patch adds support for the AES XCBC authentication algorithm
Signed-off-by: Pascal van Leeuwen <pvanleeuwen@verimatrix.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pascal van Leeuwen [Mon, 9 Sep 2019 11:13:06 +0000 (13:13 +0200)]
crypto: inside-secure - Added support for the AES CBCMAC ahash
This patch adds support for the AES-CBCMAC authentication algorithm.
Signed-off-by: Pascal van Leeuwen <pvanleeuwen@verimatrix.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pascal van Leeuwen [Mon, 9 Sep 2019 11:10:29 +0000 (13:10 +0200)]
crypto: inside-secure - Added support for CRC32
This patch adds support for the CRC32 "hash" algorithm
Signed-off-by: Pascal van Leeuwen <pvanleeuwen@verimatrix.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Linus Torvalds [Mon, 30 Sep 2019 17:35:40 +0000 (10:35 -0700)]
Linux 5.4-rc1
Linus Torvalds [Mon, 30 Sep 2019 17:25:24 +0000 (10:25 -0700)]
Merge tag 'for-5.4-rc1-tag' of git://git./linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"A bunch of fixes that accumulated in recent weeks, mostly material for
stable.
Summary:
- fix for regression from 5.3 that prevents to use balance convert
with single profile
- qgroup fixes: rescan race, accounting leak with multiple writers,
potential leak after io failure recovery
- fix for use after free in relocation (reported by KASAN)
- other error handling fixups"
* tag 'for-5.4-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: qgroup: Fix reserved data space leak if we have multiple reserve calls
btrfs: qgroup: Fix the wrong target io_tree when freeing reserved data space
btrfs: Fix a regression which we can't convert to SINGLE profile
btrfs: relocation: fix use-after-free on dead relocation roots
Btrfs: fix race setting up and completing qgroup rescan workers
Btrfs: fix missing error return if writeback for extent buffer never started
btrfs: adjust dirty_metadata_bytes after writeback failure of extent buffer
Btrfs: fix selftests failure due to uninitialized i_mode in test inodes
Linus Torvalds [Mon, 30 Sep 2019 17:16:17 +0000 (10:16 -0700)]
Merge tag 'csky-for-linus-5.4-rc1' of git://github.com/c-sky/csky-linux
Pull csky updates from Guo Ren:
"This round of csky subsystem just some fixups:
- Fix mb() synchronization problem
- Fix dma_alloc_coherent with PAGE_SO attribute
- Fix cache_op failed when cross memory ZONEs
- Optimize arch_sync_dma_for_cpu/device with dma_inv_range
- Fix ioremap function losing
- Fix arch_get_unmapped_area() implementation
- Fix defer cache flush for 610
- Support kernel non-aligned access
- Fix 610 vipt cache flush mechanism
- Fix add zero_fp fixup perf backtrace panic
- Move static keyword to the front of declaration
- Fix csky_pmu.max_period assignment
- Use generic free_initrd_mem()
- entry: Remove unneeded need_resched() loop"
* tag 'csky-for-linus-5.4-rc1' of git://github.com/c-sky/csky-linux:
csky: Move static keyword to the front of declaration
csky: entry: Remove unneeded need_resched() loop
csky: Fixup csky_pmu.max_period assignment
csky: Fixup add zero_fp fixup perf backtrace panic
csky: Use generic free_initrd_mem()
csky: Fixup 610 vipt cache flush mechanism
csky: Support kernel non-aligned access
csky: Fixup defer cache flush for 610
csky: Fixup arch_get_unmapped_area() implementation
csky: Fixup ioremap function losing
csky: Optimize arch_sync_dma_for_cpu/device with dma_inv_range
csky/dma: Fixup cache_op failed when cross memory ZONEs
csky: Fixup dma_alloc_coherent with PAGE_SO attribute
csky: Fixup mb() synchronization problem
Linus Torvalds [Mon, 30 Sep 2019 17:04:28 +0000 (10:04 -0700)]
Merge tag 'armsoc-fixes' of git://git./linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"A few fixes that have trickled in through the merge window:
- Video fixes for OMAP due to panel-dpi driver removal
- Clock fixes for OMAP that broke no-idle quirks + nfsroot on DRA7
- Fixing arch version on ASpeed ast2500
- Two fixes for reset handling on ARM SCMI"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: aspeed: ast2500 is ARMv6K
reset: reset-scmi: add missing handle initialisation
firmware: arm_scmi: reset: fix reset_state assignment in scmi_domain_reset
bus: ti-sysc: Remove unpaired sysc_clkdm_deny_idle()
ARM: dts: logicpd-som-lv: Fix i2c2 and i2c3 Pin mux
ARM: dts: am3517-evm: Fix missing video
ARM: dts: logicpd-torpedo-baseboard: Fix missing video
ARM: omap2plus_defconfig: Fix missing video
bus: ti-sysc: Fix handling of invalid clocks
bus: ti-sysc: Fix clock handling for no-idle quirks
Linus Torvalds [Mon, 30 Sep 2019 16:29:53 +0000 (09:29 -0700)]
Merge tag 'trace-v5.4-3' of git://git./linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"A few more tracing fixes:
- Fix a buffer overflow by checking nr_args correctly in probes
- Fix a warning that is reported by clang
- Fix a possible memory leak in error path of filter processing
- Fix the selftest that checks for failures, but wasn't failing
- Minor clean up on call site output of a memory trace event"
* tag 'trace-v5.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
selftests/ftrace: Fix same probe error test
mm, tracing: Print symbol name for call_site in trace events
tracing: Have error path in predicate_parse() free its allocated memory
tracing: Fix clang -Wint-in-bool-context warnings in IF_ASSIGN macro
tracing/probe: Fix to check the difference of nr_args before adding probe
Linus Torvalds [Mon, 30 Sep 2019 16:21:53 +0000 (09:21 -0700)]
Merge tag 'mmc-v5.4-2' of git://git./linux/kernel/git/ulfh/mmc
Pull more MMC updates from Ulf Hansson:
"A couple more updates/fixes for MMC:
- sdhci-pci: Add Genesys Logic GL975x support
- sdhci-tegra: Recover loss in throughput for DMA
- sdhci-of-esdhc: Fix DMA bug"
* tag 'mmc-v5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: host: sdhci-pci: Add Genesys Logic GL975x support
mmc: tegra: Implement ->set_dma_mask()
mmc: sdhci: Let drivers define their DMA mask
mmc: sdhci-of-esdhc: set DMA snooping based on DMA coherence
mmc: sdhci: improve ADMA error reporting
Krzysztof Wilczynski [Tue, 3 Sep 2019 11:36:51 +0000 (13:36 +0200)]
csky: Move static keyword to the front of declaration
Move the static keyword to the front of declaration of
csky_pmu_of_device_ids, and resolve the following compiler
warning that can be seen when building with warnings
enabled (W=1):
arch/csky/kernel/perf_event.c:1340:1: warning:
‘static’ is not at beginning of declaration [-Wold-style-declaration]
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Guo Ren <guoren@kernel.org>
Valentin Schneider [Mon, 23 Sep 2019 14:36:14 +0000 (15:36 +0100)]
csky: entry: Remove unneeded need_resched() loop
Since the enabling and disabling of IRQs within preempt_schedule_irq()
is contained in a need_resched() loop, we don't need the outer arch
code loop.
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Guo Ren <guoren@kernel.org>
Linus Torvalds [Mon, 30 Sep 2019 02:52:52 +0000 (19:52 -0700)]
Merge tag 'char-misc-5.4-rc1' of git://git./linux/kernel/git/gregkh/char-misc
Pull Documentation/process update from Greg KH:
"Here are two small Documentation/process/embargoed-hardware-issues.rst
file updates that missed my previous char/misc pull request.
The first one adds an Intel representative for the process, and the
second one cleans up the text a bit more when it comes to how the
disclosure rules work, as it was a bit confusing to some companies"
* tag 'char-misc-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Documentation/process: Clarify disclosure rules
Documentation/process: Volunteer as the ambassador for Intel
Linus Torvalds [Mon, 30 Sep 2019 02:42:07 +0000 (19:42 -0700)]
Merge branch 'work.misc' of git://git./linux/kernel/git/viro/vfs
Pull more vfs updates from Al Viro:
"A couple of misc patches"
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
afs dynroot: switch to simple_dir_operations
fs/handle.c - fix up kerneldoc
Linus Torvalds [Mon, 30 Sep 2019 02:37:32 +0000 (19:37 -0700)]
Merge tag '5.4-rc-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull more cifs updates from Steve French:
"Fixes from the recent SMB3 Test events and Storage Developer
Conference (held the last two weeks).
Here are nine smb3 patches including an important patch for debugging
traces with wireshark, with three patches marked for stable.
Additional fixes from last week to better handle some newly discovered
reparse points, and a fix the create/mkdir path for setting the mode
more atomically (in SMB3 Create security descriptor context), and one
for path name processing are still being tested so are not included
here"
* tag '5.4-rc-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
CIFS: Fix oplock handling for SMB 2.1+ protocols
smb3: missing ACL related flags
smb3: pass mode bits into create calls
smb3: Add missing reparse tags
CIFS: fix max ea value size
fs/cifs/sess.c: Remove set but not used variable 'capabilities'
fs/cifs/smb2pdu.c: Make SMB2_notify_init static
smb3: fix leak in "open on server" perf counter
smb3: allow decryption keys to be dumped by admin for debugging
Mao Han [Wed, 25 Sep 2019 09:23:02 +0000 (17:23 +0800)]
csky: Fixup csky_pmu.max_period assignment
The csky_pmu.max_period has type u64, and BIT() can only return
32 bits unsigned long on C-SKY. The initialization for max_period
will be incorrect when count_width is bigger than 32.
Use BIT_ULL()
Signed-off-by: Mao Han <han_mao@c-sky.com>
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Guo Ren [Wed, 25 Sep 2019 11:56:16 +0000 (19:56 +0800)]
csky: Fixup add zero_fp fixup perf backtrace panic
We need set fp zero to let backtrace know the end. The patch fixup perf
callchain panic problem, because backtrace didn't know what is the end
of fp.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Reported-by: Mao Han <han_mao@c-sky.com>
Mike Rapoport [Wed, 28 Aug 2019 13:35:19 +0000 (16:35 +0300)]
csky: Use generic free_initrd_mem()
The csky implementation of free_initrd_mem() is an open-coded version of
free_reserved_area() without poisoning.
Remove it and make csky use the generic version of free_initrd_mem().
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Guo Ren <guoren@kernel.org>
Linus Torvalds [Mon, 30 Sep 2019 02:25:39 +0000 (19:25 -0700)]
Merge branch 'entropy'
Merge active entropy generation updates.
This is admittedly partly "for discussion". We need to have a way
forward for the boot time deadlocks where user space ends up waiting for
more entropy, but no entropy is forthcoming because the system is
entirely idle just waiting for something to happen.
While this was triggered by what is arguably a user space bug with
GDM/gnome-session asking for secure randomness during early boot, when
they didn't even need any such truly secure thing, the issue ends up
being that our "getrandom()" interface is prone to that kind of
confusion, because people don't think very hard about whether they want
to block for sufficient amounts of entropy.
The approach here-in is to decide to not just passively wait for entropy
to happen, but to start actively collecting it if it is missing. This
is not necessarily always possible, but if the architecture has a CPU
cycle counter, there is a fair amount of noise in the exact timings of
reasonably complex loads.
We may end up tweaking the load and the entropy estimates, but this
should be at least a reasonable starting point.
As part of this, we also revert the revert of the ext4 IO pattern
improvement that ended up triggering the reported lack of external
entropy.
* getrandom() active entropy waiting:
Revert "Revert "ext4: make __ext4_get_inode_loc plug""
random: try to actively add entropy rather than passively wait for it
Linus Torvalds [Mon, 30 Sep 2019 00:59:23 +0000 (17:59 -0700)]
Revert "Revert "ext4: make __ext4_get_inode_loc plug""
This reverts commit
72dbcf72156641fde4d8ea401e977341bfd35a05.
Instead of waiting forever for entropy that may just not happen, we now
try to actively generate entropy when required, and are thus hopefully
avoiding the problem that caused the nice ext4 IO pattern fix to be
reverted.
So revert the revert.
Cc: Ahmed S. Darwish <darwish.07@gmail.com>
Cc: Ted Ts'o <tytso@mit.edu>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Alexander E. Patrakov <patrakov@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 28 Sep 2019 23:53:52 +0000 (16:53 -0700)]
random: try to actively add entropy rather than passively wait for it
For 5.3 we had to revert a nice ext4 IO pattern improvement, because it
caused a bootup regression due to lack of entropy at bootup together
with arguably broken user space that was asking for secure random
numbers when it really didn't need to.
See commit
72dbcf721566 (Revert "ext4: make __ext4_get_inode_loc plug").
This aims to solve the issue by actively generating entropy noise using
the CPU cycle counter when waiting for the random number generator to
initialize. This only works when you have a high-frequency time stamp
counter available, but that's the case on all modern x86 CPU's, and on
most other modern CPU's too.
What we do is to generate jitter entropy from the CPU cycle counter
under a somewhat complex load: calling the scheduler while also
guaranteeing a certain amount of timing noise by also triggering a
timer.
I'm sure we can tweak this, and that people will want to look at other
alternatives, but there's been a number of papers written on jitter
entropy, and this should really be fairly conservative by crediting one
bit of entropy for every timer-induced jump in the cycle counter. Not
because the timer itself would be all that unpredictable, but because
the interaction between the timer and the loop is going to be.
Even if (and perhaps particularly if) the timer actually happens on
another CPU, the cacheline interaction between the loop that reads the
cycle counter and the timer itself firing is going to add perturbations
to the cycle counter values that get mixed into the entropy pool.
As Thomas pointed out, with a modern out-of-order CPU, even quite simple
loops show a fair amount of hard-to-predict timing variability even in
the absense of external interrupts. But this tries to take that further
by actually having a fairly complex interaction.
This is not going to solve the entropy issue for architectures that have
no CPU cycle counter, but it's not clear how (and if) that is solvable,
and the hardware in question is largely starting to be irrelevant. And
by doing this we can at least avoid some of the even more contentious
approaches (like making the entropy waiting time out in order to avoid
the possibly unbounded waiting).
Cc: Ahmed Darwish <darwish.07@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Nicholas Mc Guire <hofrat@opentech.at>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Alexander E. Patrakov <patrakov@gmail.com>
Cc: Lennart Poettering <mzxreary@0pointer.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Olof Johansson [Sun, 29 Sep 2019 18:19:25 +0000 (11:19 -0700)]
Merge tag 'fixes-5.4-merge-window' of git://git./linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omap variants
Few fixes for ti-sysc interconnect target module driver for no-idle
quirks that caused nfsroot to fail on some dra7 boards.
And let's fixes to get LCD working again for logicpd board that got
broken a while back with removal of panel-dpi driver. We need to now
use generic CONFIG_DRM_PANEL_SIMPLE instead.
* tag 'fixes-5.4-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Remove unpaired sysc_clkdm_deny_idle()
ARM: dts: logicpd-som-lv: Fix i2c2 and i2c3 Pin mux
ARM: dts: am3517-evm: Fix missing video
ARM: dts: logicpd-torpedo-baseboard: Fix missing video
ARM: omap2plus_defconfig: Fix missing video
bus: ti-sysc: Fix handling of invalid clocks
bus: ti-sysc: Fix clock handling for no-idle quirks
Link: https://lore.kernel.org/r/pull-1568819401-72461@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sun, 29 Sep 2019 18:19:18 +0000 (11:19 -0700)]
Merge tag 'scmi-fixes-5.4' of git://git./linux/kernel/git/sudeep.holla/linux into arm/fixes
ARM SCMI fixes for v5.4
Couple of fixes: one in scmi reset driver initialising missed scmi handle
and an other in scmi reset API implementation fixing the assignment of
reset state
* tag 'scmi-fixes-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
reset: reset-scmi: add missing handle initialisation
firmware: arm_scmi: reset: fix reset_state assignment in scmi_domain_reset
Link: https://lore.kernel.org/r/20190918142139.GA4370@bogus
Signed-off-by: Olof Johansson <olof@lixom.net>
Linus Torvalds [Sun, 29 Sep 2019 17:33:41 +0000 (10:33 -0700)]
Merge tag 'libnvdimm-fixes-5.4-rc1' of git://git./linux/kernel/git/nvdimm/nvdimm
More libnvdimm updates from Dan Williams:
- Complete the reworks to interoperate with powerpc dynamic huge page
sizes
- Fix a crash due to missed accounting for the powerpc 'struct
page'-memmap mapping granularity
- Fix badblock initialization for volatile (DRAM emulated) pmem ranges
- Stop triggering request_key() notifications to userspace when
NVDIMM-security is disabled / not present
- Miscellaneous small fixups
* tag 'libnvdimm-fixes-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
libnvdimm/region: Enable MAP_SYNC for volatile regions
libnvdimm: prevent nvdimm from requesting key when security is disabled
libnvdimm/region: Initialize bad block for volatile namespaces
libnvdimm/nfit_test: Fix acpi_handle redefinition
libnvdimm/altmap: Track namespace boundaries in altmap
libnvdimm: Fix endian conversion issues
libnvdimm/dax: Pick the right alignment default when creating dax devices
powerpc/book3s64: Export has_transparent_hugepage() related functions.
Linus Torvalds [Sun, 29 Sep 2019 17:24:23 +0000 (10:24 -0700)]
Merge branch 'linus' of git://git./linux/kernel/git/evalenti/linux-soc-thermal
Pull thermal SoC updates from Eduardo Valentin:
"This is a really small pull in the midst of a lot of pending patches.
We are in the middle of restructuring how we are maintaining the
thermal subsystem, as per discussion in our last LPC. For now, I am
sending just some changes that were pending in my tree. Looking
forward to get a more streamlined process in the next merge window"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal: db8500: Rewrite to be a pure OF sensor
thermal: db8500: Use dev helper variable
thermal: db8500: Finalize device tree conversion
thermal: thermal_mmio: remove some dead code
Linus Torvalds [Sun, 29 Sep 2019 17:20:16 +0000 (10:20 -0700)]
Merge branch 'i2c/for-next' of git://git./linux/kernel/git/wsa/linux
Pull more i2c updates from Wolfram Sang:
- make Lenovo Yoga C630 boot now that the dependencies are merged
- restore BlockProcessCall for i801, accidently removed in this merge
window
- a bugfix for the riic driver
- an improvement to the slave-eeprom driver which should have been in
the first pull request but sadly got lost in the process
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: slave-eeprom: Add read only mode
i2c: i801: Bring back Block Process Call support for certain platforms
i2c: riic: Clear NACK in tend isr
i2c: qcom-geni: Disable DMA processing on the Lenovo Yoga C630
Linus Torvalds [Sun, 29 Sep 2019 17:00:14 +0000 (10:00 -0700)]
Merge tag 'iommu-fixes-5.4-rc1' of git://git./linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
"A couple of fixes for the AMD IOMMU driver have piled up:
- Some fixes for the reworked IO page-table which caused memory leaks
or did not allow to downgrade mappings under some conditions.
- Locking fixes to fix a couple of possible races around accessing
'struct protection_domain'. The races got introduced when the
dma-ops path became lock-less in the fast-path"
* tag 'iommu-fixes-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Lock code paths traversing protection_domain->dev_list
iommu/amd: Lock dev_data in attach/detach code paths
iommu/amd: Check for busy devices earlier in attach_device()
iommu/amd: Take domain->lock for complete attach/detach path
iommu/amd: Remove amd_iommu_devtable_lock
iommu/amd: Remove domain->updated
iommu/amd: Wait for completion of IOTLB flush in attach_device
iommu/amd: Unmap all L7 PTEs when downgrading page-sizes
iommu/amd: Introduce first_pte_l7() helper
iommu/amd: Fix downgrading default page-sizes in alloc_pte()
iommu/amd: Fix pages leak in free_pagetable()
Thomas Gleixner [Wed, 25 Sep 2019 08:29:49 +0000 (10:29 +0200)]
Documentation/process: Clarify disclosure rules
The role of the contact list provided by the disclosing party and how it
affects the disclosure process and the ability to include experts into
the development process is not really well explained.
Neither is it entirely clear when the disclosing party will be informed
about the fact that a developer who is not covered by an employer NDA needs
to be brought in and disclosed.
Explain the role of the contact list and the information policy along with
an eventual conflict resolution better.
Reported-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.1909251028390.10825@nanos.tec.linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Sun, 29 Sep 2019 00:47:33 +0000 (17:47 -0700)]
Merge git://git./linux/kernel/git/netdev/net
Pull networking fixes from David Miller:
1) Sanity check URB networking device parameters to avoid divide by
zero, from Oliver Neukum.
2) Disable global multicast filter in NCSI, otherwise LLDP and IPV6
don't work properly. Longer term this needs a better fix tho. From
Vijay Khemka.
3) Small fixes to selftests (use ping when ping6 is not present, etc.)
from David Ahern.
4) Bring back rt_uses_gateway member of struct rtable, it's semantics
were not well understood and trying to remove it broke things. From
David Ahern.
5) Move usbnet snaity checking, ignore endpoints with invalid
wMaxPacketSize. From Bjørn Mork.
6) Missing Kconfig deps for sja1105 driver, from Mao Wenan.
7) Various small fixes to the mlx5 DR steering code, from Alaa Hleihel,
Alex Vesker, and Yevgeny Kliteynik
8) Missing CAP_NET_RAW checks in various places, from Ori Nimron.
9) Fix crash when removing sch_cbs entry while offloading is enabled,
from Vinicius Costa Gomes.
10) Signedness bug fixes, generally in looking at the result given by
of_get_phy_mode() and friends. From Dan Crapenter.
11) Disable preemption around BPF_PROG_RUN() calls, from Eric Dumazet.
12) Don't create VRF ipv6 rules if ipv6 is disabled, from David Ahern.
13) Fix quantization code in tcp_bbr, from Kevin Yang.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (127 commits)
net: tap: clean up an indentation issue
nfp: abm: fix memory leak in nfp_abm_u32_knode_replace
tcp: better handle TCP_USER_TIMEOUT in SYN_SENT state
sk_buff: drop all skb extensions on free and skb scrubbing
tcp_bbr: fix quantization code to not raise cwnd if not probing bandwidth
mlxsw: spectrum_flower: Fail in case user specifies multiple mirror actions
Documentation: Clarify trap's description
mlxsw: spectrum: Clear VLAN filters during port initialization
net: ena: clean up indentation issue
NFC: st95hf: clean up indentation issue
net: phy: micrel: add Asym Pause workaround for KSZ9021
net: socionext: ave: Avoid using netdev_err() before calling register_netdev()
ptp: correctly disable flags on old ioctls
lib: dimlib: fix help text typos
net: dsa: microchip: Always set regmap stride to 1
nfp: flower: fix memory leak in nfp_flower_spawn_vnic_reprs
nfp: flower: prevent memory leak in nfp_flower_spawn_phy_reprs
net/sched: Set default of CONFIG_NET_TC_SKB_EXT to N
vrf: Do not attempt to create IPv6 mcast rule if IPv6 is disabled
net: sched: sch_sfb: don't call qdisc_put() while holding tree lock
...
Linus Torvalds [Sat, 28 Sep 2019 21:26:47 +0000 (14:26 -0700)]
Merge branch 'hugepage-fallbacks' (hugepatch patches from David Rientjes)
Merge hugepage allocation updates from David Rientjes:
"We (mostly Linus, Andrea, and myself) have been discussing offlist how
to implement a sane default allocation strategy for hugepages on NUMA
platforms.
With these reverts in place, the page allocator will happily allocate
a remote hugepage immediately rather than try to make a local hugepage
available. This incurs a substantial performance degradation when
memory compaction would have otherwise made a local hugepage
available.
This series reverts those reverts and attempts to propose a more sane
default allocation strategy specifically for hugepages. Andrea
acknowledges this is likely to fix the swap storms that he originally
reported that resulted in the patches that removed __GFP_THISNODE from
hugepage allocations.
The immediate goal is to return 5.3 to the behavior the kernel has
implemented over the past several years so that remote hugepages are
not immediately allocated when local hugepages could have been made
available because the increased access latency is untenable.
The next goal is to introduce a sane default allocation strategy for
hugepages allocations in general regardless of the configuration of
the system so that we prevent thrashing of local memory when
compaction is unlikely to succeed and can prefer remote hugepages over
remote native pages when the local node is low on memory."
Note on timing: this reverts the hugepage VM behavior changes that got
introduced fairly late in the 5.3 cycle, and that fixed a huge
performance regression for certain loads that had been around since
4.18.
Andrea had this note:
"The regression of 4.18 was that it was taking hours to start a VM
where 3.10 was only taking a few seconds, I reported all the details
on lkml when it was finally tracked down in August 2018.
https://lore.kernel.org/linux-mm/
20180820032640.9896-2-aarcange@redhat.com/
__GFP_THISNODE in MADV_HUGEPAGE made the above enterprise vfio
workload degrade like in the "current upstream" above. And it still
would have been that bad as above until 5.3-rc5"
where the bad behavior ends up happening as you fill up a local node,
and without that change, you'd get into the nasty swap storm behavior
due to compaction working overtime to make room for more memory on the
nodes.
As a result 5.3 got the two performance fix reverts in rc5.
However, David Rientjes then noted that those performance fixes in turn
regressed performance for other loads - although not quite to the same
degree. He suggested reverting the reverts and instead replacing them
with two small changes to how hugepage allocations are done (patch
descriptions rephrased by me):
- "avoid expensive reclaim when compaction may not succeed": just admit
that the allocation failed when you're trying to allocate a huge-page
and compaction wasn't successful.
- "allow hugepage fallback to remote nodes when madvised": when that
node-local huge-page allocation failed, retry without forcing the
local node.
but by then I judged it too late to replace the fixes for a 5.3 release.
So 5.3 was released with behavior that harked back to the pre-4.18 logic.
But now we're in the merge window for 5.4, and we can see if this
alternate model fixes not just the horrendous swap storm behavior, but
also restores the performance regression that the late reverts caused.
Fingers crossed.
* emailed patches from David Rientjes <rientjes@google.com>:
mm, page_alloc: allow hugepage fallback to remote nodes when madvised
mm, page_alloc: avoid expensive reclaim when compaction may not succeed
Revert "Revert "Revert "mm, thp: consolidate THP gfp handling into alloc_hugepage_direct_gfpmask""
Revert "Revert "mm, thp: restore node-local hugepage allocations""
Steven Rostedt (VMware) [Fri, 27 Sep 2019 15:10:22 +0000 (11:10 -0400)]
selftests/ftrace: Fix same probe error test
The "same probe" selftest that tests that adding the same probe fails
doesn't add the same probe and passes, which fails the test.
Fixes: b78b94b82122 ("selftests/ftrace: Update kprobe event error testcase")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Changbin Du [Sat, 14 Sep 2019 10:32:15 +0000 (18:32 +0800)]
mm, tracing: Print symbol name for call_site in trace events
To improve the readability of raw slab trace points, print the call_site ip
using '%pS'. Then we can grep events with function names.
[002] .... 808.188897: kmem_cache_free: call_site=putname+0x47/0x50 ptr=
00000000cef40c80
[002] .... 808.188898: kfree: call_site=security_cred_free+0x42/0x50 ptr=
0000000062400820
[002] .... 808.188904: kmem_cache_free: call_site=put_cred_rcu+0x88/0xa0 ptr=
0000000058d74ef8
[002] .... 808.188913: kmem_cache_alloc: call_site=prepare_creds+0x26/0x100 ptr=
0000000058d74ef8 bytes_req=168 bytes_alloc=576 gfp_flags=GFP_KERNEL
[002] .... 808.188917: kmalloc: call_site=security_prepare_creds+0x77/0xa0 ptr=
0000000062400820 bytes_req=8 bytes_alloc=336 gfp_flags=GFP_KERNEL|__GFP_ZERO
[002] .... 808.188920: kmem_cache_alloc: call_site=getname_flags+0x4f/0x1e0 ptr=
00000000cef40c80 bytes_req=4096 bytes_alloc=4480 gfp_flags=GFP_KERNEL
[002] .... 808.188925: kmem_cache_free: call_site=putname+0x47/0x50 ptr=
00000000cef40c80
[002] .... 808.188926: kfree: call_site=security_cred_free+0x42/0x50 ptr=
0000000062400820
[002] .... 808.188931: kmem_cache_free: call_site=put_cred_rcu+0x88/0xa0 ptr=
0000000058d74ef8
Link: http://lkml.kernel.org/r/20190914103215.23301-1-changbin.du@gmail.com
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Navid Emamdoost [Fri, 20 Sep 2019 22:57:59 +0000 (17:57 -0500)]
tracing: Have error path in predicate_parse() free its allocated memory
In predicate_parse, there is an error path that is not going to
out_free instead it returns directly which leads to a memory leak.
Link: http://lkml.kernel.org/r/20190920225800.3870-1-navid.emamdoost@gmail.com
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Nathan Chancellor [Thu, 26 Sep 2019 16:22:59 +0000 (09:22 -0700)]
tracing: Fix clang -Wint-in-bool-context warnings in IF_ASSIGN macro
After r372664 in clang, the IF_ASSIGN macro causes a couple hundred
warnings along the lines of:
kernel/trace/trace_output.c:1331:2: warning: converting the enum
constant to a boolean [-Wint-in-bool-context]
kernel/trace/trace.h:409:3: note: expanded from macro
'trace_assign_type'
IF_ASSIGN(var, ent, struct ftrace_graph_ret_entry,
^
kernel/trace/trace.h:371:14: note: expanded from macro 'IF_ASSIGN'
WARN_ON(id && (entry)->type != id); \
^
264 warnings generated.
This warning can catch issues with constructs like:
if (state == A || B)
where the developer really meant:
if (state == A || state == B)
This is currently the only occurrence of the warning in the kernel
tree across defconfig, allyesconfig, allmodconfig for arm32, arm64,
and x86_64. Add the implicit '!= 0' to the WARN_ON statement to fix
the warnings and find potential issues in the future.
Link: https://github.com/llvm/llvm-project/commit/28b38c277a2941e9e891b2db30652cfd962f070b
Link: https://github.com/ClangBuiltLinux/linux/issues/686
Link: http://lkml.kernel.org/r/20190926162258.466321-1-natechancellor@gmail.com
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Masami Hiramatsu [Sat, 28 Sep 2019 09:53:29 +0000 (05:53 -0400)]
tracing/probe: Fix to check the difference of nr_args before adding probe
Steven reported that a test triggered:
==================================================================
BUG: KASAN: slab-out-of-bounds in trace_kprobe_create+0xa9e/0xe40
Read of size 8 at addr
ffff8880c4f25a48 by task ftracetest/4798
CPU: 2 PID: 4798 Comm: ftracetest Not tainted 5.3.0-rc6-test+ #30
Hardware name: Hewlett-Packard HP Compaq Pro 6300 SFF/339A, BIOS K01 v03.03 07/14/2016
Call Trace:
dump_stack+0x7c/0xc0
? trace_kprobe_create+0xa9e/0xe40
print_address_description+0x6c/0x332
? trace_kprobe_create+0xa9e/0xe40
? trace_kprobe_create+0xa9e/0xe40
__kasan_report.cold.6+0x1a/0x3b
? trace_kprobe_create+0xa9e/0xe40
kasan_report+0xe/0x12
trace_kprobe_create+0xa9e/0xe40
? print_kprobe_event+0x280/0x280
? match_held_lock+0x1b/0x240
? find_held_lock+0xac/0xd0
? fs_reclaim_release.part.112+0x5/0x20
? lock_downgrade+0x350/0x350
? kasan_unpoison_shadow+0x30/0x40
? __kasan_kmalloc.constprop.6+0xc1/0xd0
? trace_kprobe_create+0xe40/0xe40
? trace_kprobe_create+0xe40/0xe40
create_or_delete_trace_kprobe+0x2e/0x60
trace_run_command+0xc3/0xe0
? trace_panic_handler+0x20/0x20
? kasan_unpoison_shadow+0x30/0x40
trace_parse_run_command+0xdc/0x163
vfs_write+0xe1/0x240
ksys_write+0xba/0x150
? __ia32_sys_read+0x50/0x50
? tracer_hardirqs_on+0x61/0x180
? trace_hardirqs_off_caller+0x43/0x110
? mark_held_locks+0x29/0xa0
? do_syscall_64+0x14/0x260
do_syscall_64+0x68/0x260
Fix to check the difference of nr_args before adding probe
on existing probes. This also may set the error log index
bigger than the number of command parameters. In that case
it sets the error position is next to the last parameter.
Link: http://lkml.kernel.org/r/156966474783.3478.13217501608215769150.stgit@devnote2
Fixes: ca89bc071d5e ("tracing/kprobe: Add multi-probe per event support")
Reported-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
David Rientjes [Wed, 4 Sep 2019 19:54:25 +0000 (12:54 -0700)]
mm, page_alloc: allow hugepage fallback to remote nodes when madvised
For systems configured to always try hard to allocate transparent
hugepages (thp defrag setting of "always") or for memory that has been
explicitly madvised to MADV_HUGEPAGE, it is often better to fallback to
remote memory to allocate the hugepage if the local allocation fails
first.
The point is to allow the initial call to __alloc_pages_node() to attempt
to defragment local memory to make a hugepage available, if possible,
rather than immediately fallback to remote memory. Local hugepages will
always have a better access latency than remote (huge)pages, so an attempt
to make a hugepage available locally is always preferred.
If memory compaction cannot be successful locally, however, it is likely
better to fallback to remote memory. This could take on two forms: either
allow immediate fallback to remote memory or do per-zone watermark checks.
It would be possible to fallback only when per-zone watermarks fail for
order-0 memory, since that would require local reclaim for all subsequent
faults so remote huge allocation is likely better than thrashing the local
zone for large workloads.
In this case, it is assumed that because the system is configured to try
hard to allocate hugepages or the vma is advised to explicitly want to try
hard for hugepages that remote allocation is better when local allocation
and memory compaction have both failed.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Stefan Priebe - Profihost AG <s.priebe@profihost.ag>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Rientjes [Wed, 4 Sep 2019 19:54:22 +0000 (12:54 -0700)]
mm, page_alloc: avoid expensive reclaim when compaction may not succeed
Memory compaction has a couple significant drawbacks as the allocation
order increases, specifically:
- isolate_freepages() is responsible for finding free pages to use as
migration targets and is implemented as a linear scan of memory
starting at the end of a zone,
- failing order-0 watermark checks in memory compaction does not account
for how far below the watermarks the zone actually is: to enable
migration, there must be *some* free memory available. Per the above,
watermarks are not always suffficient if isolate_freepages() cannot
find the free memory but it could require hundreds of MBs of reclaim to
even reach this threshold (read: potentially very expensive reclaim with
no indication compaction can be successful), and
- if compaction at this order has failed recently so that it does not even
run as a result of deferred compaction, looping through reclaim can often
be pointless.
For hugepage allocations, these are quite substantial drawbacks because
these are very high order allocations (order-9 on x86) and falling back to
doing reclaim can potentially be *very* expensive without any indication
that compaction would even be successful.
Reclaim itself is unlikely to free entire pageblocks and certainly no
reliance should be put on it to do so in isolation (recall lumpy reclaim).
This means we should avoid reclaim and simply fail hugepage allocation if
compaction is deferred.
It is also not helpful to thrash a zone by doing excessive reclaim if
compaction may not be able to access that memory. If order-0 watermarks
fail and the allocation order is sufficiently large, it is likely better
to fail the allocation rather than thrashing the zone.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Stefan Priebe - Profihost AG <s.priebe@profihost.ag>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Rientjes [Wed, 4 Sep 2019 19:54:20 +0000 (12:54 -0700)]
Revert "Revert "Revert "mm, thp: consolidate THP gfp handling into alloc_hugepage_direct_gfpmask""
This reverts commit
92717d429b38e4f9f934eed7e605cc42858f1839.
Since commit
a8282608c88e ("Revert "mm, thp: restore node-local hugepage
allocations"") is reverted in this series, it is better to restore the
previous 5.2 behavior between the thp allocation and the page allocator
rather than to attempt any consolidation or cleanup for a policy that is
now reverted. It's less risky during an rc cycle and subsequent patches
in this series further modify the same policy that the pre-5.3 behavior
implements.
Consolidation and cleanup can be done subsequent to a sane default page
allocation strategy, so this patch reverts a cleanup done on a strategy
that is now reverted and thus is the least risky option.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Stefan Priebe - Profihost AG <s.priebe@profihost.ag>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Rientjes [Wed, 4 Sep 2019 19:54:18 +0000 (12:54 -0700)]
Revert "Revert "mm, thp: restore node-local hugepage allocations""
This reverts commit
a8282608c88e08b1782141026eab61204c1e533f.
The commit references the original intended semantic for MADV_HUGEPAGE
which has subsequently taken on three unique purposes:
- enables or disables thp for a range of memory depending on the system's
config (is thp "enabled" set to "always" or "madvise"),
- determines the synchronous compaction behavior for thp allocations at
fault (is thp "defrag" set to "always", "defer+madvise", or "madvise"),
and
- reverts a previous MADV_NOHUGEPAGE (there is no madvise mode to only
clear previous hugepage advice).
These are the three purposes that currently exist in 5.2 and over the
past several years that userspace has been written around. Adding a
NUMA locality preference adds a fourth dimension to an already conflated
advice mode.
Based on the semantic that MADV_HUGEPAGE has provided over the past
several years, there exist workloads that use the tunable based on these
principles: specifically that the allocation should attempt to
defragment a local node before falling back. It is agreed that remote
hugepages typically (but not always) have a better access latency than
remote native pages, although on Naples this is at parity for
intersocket.
The revert commit that this patch reverts allows hugepage allocation to
immediately allocate remotely when local memory is fragmented. This is
contrary to the semantic of MADV_HUGEPAGE over the past several years:
that is, memory compaction should be attempted locally before falling
back.
The performance degradation of remote hugepages over local hugepages on
Rome, for example, is 53.5% increased access latency. For this reason,
the goal is to revert back to the 5.2 and previous behavior that would
attempt local defragmentation before falling back. With the patch that
is reverted by this patch, we see performance degradations at the tail
because the allocator happily allocates the remote hugepage rather than
even attempting to make a local hugepage available.
zone_reclaim_mode is not a solution to this problem since it does not
only impact hugepage allocations but rather changes the memory
allocation strategy for *all* page allocations.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Stefan Priebe - Profihost AG <s.priebe@profihost.ag>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 28 Sep 2019 20:43:00 +0000 (13:43 -0700)]
Merge tag 'powerpc-5.4-2' of git://git./linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"An assortment of fixes that were either missed by me, or didn't arrive
quite in time for the first v5.4 pull.
- Most notable is a fix for an issue with tlbie (broadcast TLB
invalidation) on Power9, when using the Radix MMU. The tlbie can
race with an mtpid (move to PID register, essentially MMU context
switch) on another thread of the core, which can cause stores to
continue to go to a page after it's unmapped.
- A fix in our KVM code to add a missing barrier, the lack of which
has been observed to cause missed IPIs and subsequently stuck CPUs
in the host.
- A change to the way we initialise PCR (Processor Compatibility
Register) to make it forward compatible with future CPUs.
- On some older PowerVM systems our H_BLOCK_REMOVE support could
oops, fix it to detect such systems and fallback to the old
invalidation method.
- A fix for an oops seen on some machines when using KASAN on 32-bit.
- A handful of other minor fixes, and two new selftests.
Thanks to: Alistair Popple, Aneesh Kumar K.V, Christophe Leroy,
Gustavo Romero, Joel Stanley, Jordan Niethe, Laurent Dufour, Michael
Roth, Oliver O'Halloran"
* tag 'powerpc-5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/eeh: Fix eeh eeh_debugfs_break_device() with SRIOV devices
powerpc/nvdimm: use H_SCM_QUERY hcall on H_OVERLAP error
powerpc/nvdimm: Use HCALL error as the return value
selftests/powerpc: Add test case for tlbie vs mtpidr ordering issue
powerpc/mm: Fixup tlbie vs mtpidr/mtlpidr ordering issue on POWER9
powerpc/book3s64/radix: Rename CPU_FTR_P9_TLBIE_BUG feature flag
powerpc/book3s64/mm: Don't do tlbie fixup for some hardware revisions
powerpc/pseries: Call H_BLOCK_REMOVE when supported
powerpc/pseries: Read TLB Block Invalidate Characteristics
KVM: PPC: Book3S HV: use smp_mb() when setting/clearing host_ipi flag
powerpc/mm: Fix an Oops in kasan_mmu_init()
powerpc/mm: Add a helper to select PAGE_KERNEL_RO or PAGE_READONLY
powerpc/64s: Set reserved PCR bits
powerpc: Fix definition of PCR bits to work with old binutils
powerpc/book3s64/radix: Remove WARN_ON in destroy_context()
powerpc/tm: Add tm-poison test
Linus Torvalds [Sat, 28 Sep 2019 20:37:41 +0000 (13:37 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fix from Ingo Molnar:
"A kexec fix for the case when GCC_PLUGIN_STACKLEAK=y is enabled"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/purgatory: Disable the stackleak GCC plugin for the purgatory
Linus Torvalds [Sat, 28 Sep 2019 19:39:07 +0000 (12:39 -0700)]
Merge branch 'sched-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
- Apply a number of membarrier related fixes and cleanups, which fixes
a use-after-free race in the membarrier code
- Introduce proper RCU protection for tasks on the runqueue - to get
rid of the subtle task_rcu_dereference() interface that was easy to
get wrong
- Misc fixes, but also an EAS speedup
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Avoid redundant EAS calculation
sched/core: Remove double update_max_interval() call on CPU startup
sched/core: Fix preempt_schedule() interrupt return comment
sched/fair: Fix -Wunused-but-set-variable warnings
sched/core: Fix migration to invalid CPU in __set_cpus_allowed_ptr()
sched/membarrier: Return -ENOMEM to userspace on memory allocation failure
sched/membarrier: Skip IPIs when mm->mm_users == 1
selftests, sched/membarrier: Add multi-threaded test
sched/membarrier: Fix p->mm->membarrier_state racy load
sched/membarrier: Call sync_core only before usermode for same mm
sched/membarrier: Remove redundant check
sched/membarrier: Fix private expedited registration check
tasks, sched/core: RCUify the assignment of rq->curr
tasks, sched/core: With a grace period after finish_task_switch(), remove unnecessary code
tasks, sched/core: Ensure tasks are available for a grace period after leaving the runqueue
tasks: Add a count of task RCU users
sched/core: Convert vcpu_is_preempted() from macro to an inline function
sched/fair: Remove unused cfs_rq_clock_task() function
Björn Ardö [Fri, 6 Sep 2019 14:06:09 +0000 (16:06 +0200)]
i2c: slave-eeprom: Add read only mode
Add read-only versions of all EEPROMs. These versions are read-only
on the i2c side, but can be written from the sysfs side.
Signed-off-by: Björn Ardö <bjorn.ardo@axis.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Jarkko Nikula [Fri, 27 Sep 2019 11:09:11 +0000 (14:09 +0300)]
i2c: i801: Bring back Block Process Call support for certain platforms
Commit
b84398d6d7f9 ("i2c: i801: Use iTCO version 6 in Cannon Lake PCH
and beyond") looks like to drop by accident Block Write-Block Read Process
Call support for Intel Sunrisepoint, Lewisburg, Denverton and Kaby Lake.
That support was added for above and newer platforms by the commit
315cd67c9453 ("i2c: i801: Add Block Write-Block Read Process Call
support") so bring it back for above platforms.
Fixes: b84398d6d7f9 ("i2c: i801: Use iTCO version 6 in Cannon Lake PCH and beyond")
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Chris Brandt [Thu, 26 Sep 2019 12:19:09 +0000 (07:19 -0500)]
i2c: riic: Clear NACK in tend isr
The NACKF flag should be cleared in INTRIICNAKI interrupt processing as
description in HW manual.
This issue shows up quickly when PREEMPT_RT is applied and a device is
probed that is not plugged in (like a touchscreen controller). The result
is endless interrupts that halt system boot.
Fixes: 310c18a41450 ("i2c: riic: add driver")
Cc: stable@vger.kernel.org
Reported-by: Chien Nguyen <chien.nguyen.eb@rvc.renesas.com>
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Lee Jones [Thu, 5 Sep 2019 19:24:12 +0000 (20:24 +0100)]
i2c: qcom-geni: Disable DMA processing on the Lenovo Yoga C630
We have a production-level laptop (Lenovo Yoga C630) which is exhibiting
a rather horrific bug. When I2C HID devices are being scanned for at
boot-time the QCom Geni based I2C (Serial Engine) attempts to use DMA.
When it does, the laptop reboots and the user never sees the OS.
Attempts are being made to debug the reason for the spontaneous reboot.
No luck so far, hence the requirement for this hot-fix. This workaround
will be removed once we have a viable fix.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Linus Torvalds [Sat, 28 Sep 2019 15:14:15 +0000 (08:14 -0700)]
Merge branch 'next-lockdown' of git://git./linux/kernel/git/jmorris/linux-security
Pull kernel lockdown mode from James Morris:
"This is the latest iteration of the kernel lockdown patchset, from
Matthew Garrett, David Howells and others.
From the original description:
This patchset introduces an optional kernel lockdown feature,
intended to strengthen the boundary between UID 0 and the kernel.
When enabled, various pieces of kernel functionality are restricted.
Applications that rely on low-level access to either hardware or the
kernel may cease working as a result - therefore this should not be
enabled without appropriate evaluation beforehand.
The majority of mainstream distributions have been carrying variants
of this patchset for many years now, so there's value in providing a
doesn't meet every distribution requirement, but gets us much closer
to not requiring external patches.
There are two major changes since this was last proposed for mainline:
- Separating lockdown from EFI secure boot. Background discussion is
covered here: https://lwn.net/Articles/751061/
- Implementation as an LSM, with a default stackable lockdown LSM
module. This allows the lockdown feature to be policy-driven,
rather than encoding an implicit policy within the mechanism.
The new locked_down LSM hook is provided to allow LSMs to make a
policy decision around whether kernel functionality that would allow
tampering with or examining the runtime state of the kernel should be
permitted.
The included lockdown LSM provides an implementation with a simple
policy intended for general purpose use. This policy provides a coarse
level of granularity, controllable via the kernel command line:
lockdown={integrity|confidentiality}
Enable the kernel lockdown feature. If set to integrity, kernel features
that allow userland to modify the running kernel are disabled. If set to
confidentiality, kernel features that allow userland to extract
confidential information from the kernel are also disabled.
This may also be controlled via /sys/kernel/security/lockdown and
overriden by kernel configuration.
New or existing LSMs may implement finer-grained controls of the
lockdown features. Refer to the lockdown_reason documentation in
include/linux/security.h for details.
The lockdown feature has had signficant design feedback and review
across many subsystems. This code has been in linux-next for some
weeks, with a few fixes applied along the way.
Stephen Rothwell noted that commit
9d1f8be5cf42 ("bpf: Restrict bpf
when kernel lockdown is in confidentiality mode") is missing a
Signed-off-by from its author. Matthew responded that he is providing
this under category (c) of the DCO"
* 'next-lockdown' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (31 commits)
kexec: Fix file verification on S390
security: constify some arrays in lockdown LSM
lockdown: Print current->comm in restriction messages
efi: Restrict efivar_ssdt_load when the kernel is locked down
tracefs: Restrict tracefs when the kernel is locked down
debugfs: Restrict debugfs when the kernel is locked down
kexec: Allow kexec_file() with appropriate IMA policy when locked down
lockdown: Lock down perf when in confidentiality mode
bpf: Restrict bpf when kernel lockdown is in confidentiality mode
lockdown: Lock down tracing and perf kprobes when in confidentiality mode
lockdown: Lock down /proc/kcore
x86/mmiotrace: Lock down the testmmiotrace module
lockdown: Lock down module params that specify hardware parameters (eg. ioport)
lockdown: Lock down TIOCSSERIAL
lockdown: Prohibit PCMCIA CIS storage when the kernel is locked down
acpi: Disable ACPI table override if the kernel is locked down
acpi: Ignore acpi_rsdp kernel param when the kernel has been locked down
ACPI: Limit access to custom_method when the kernel is locked down
x86/msr: Restrict MSR access when the kernel is locked down
x86: Lock down IO port access when the kernel is locked down
...
Joerg Roedel [Wed, 25 Sep 2019 13:23:00 +0000 (15:23 +0200)]
iommu/amd: Lock code paths traversing protection_domain->dev_list
The traversing of this list requires protection_domain->lock to be taken
to avoid nasty races with attach/detach code. Make sure the lock is held
on all code-paths traversing this list.
Reported-by: Filippo Sironi <sironi@amazon.de>
Fixes: 92d420ec028d ("iommu/amd: Relax locking in dma_ops path")
Reviewed-by: Filippo Sironi <sironi@amazon.de>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Joerg Roedel [Wed, 25 Sep 2019 13:22:59 +0000 (15:22 +0200)]
iommu/amd: Lock dev_data in attach/detach code paths
Make sure that attaching a detaching a device can't race against each
other and protect the iommu_dev_data with a spin_lock in these code
paths.
Fixes: 92d420ec028d ("iommu/amd: Relax locking in dma_ops path")
Reviewed-by: Filippo Sironi <sironi@amazon.de>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Joerg Roedel [Wed, 25 Sep 2019 13:22:58 +0000 (15:22 +0200)]
iommu/amd: Check for busy devices earlier in attach_device()
Check early in attach_device whether the device is already attached to a
domain. This also simplifies the code path so that __attach_device() can
be removed.
Fixes: 92d420ec028d ("iommu/amd: Relax locking in dma_ops path")
Reviewed-by: Filippo Sironi <sironi@amazon.de>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Joerg Roedel [Wed, 25 Sep 2019 13:22:57 +0000 (15:22 +0200)]
iommu/amd: Take domain->lock for complete attach/detach path
The code-paths before __attach_device() and __detach_device() are called
also access and modify domain state, so take the domain lock there too.
This allows to get rid of the __detach_device() function.
Fixes: 92d420ec028d ("iommu/amd: Relax locking in dma_ops path")
Reviewed-by: Filippo Sironi <sironi@amazon.de>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Joerg Roedel [Wed, 25 Sep 2019 13:22:56 +0000 (15:22 +0200)]
iommu/amd: Remove amd_iommu_devtable_lock
The lock is not necessary because the device table does not
contain shared state that needs protection. Locking is only
needed on an individual entry basis, and that needs to
happen on the iommu_dev_data level.
Fixes: 92d420ec028d ("iommu/amd: Relax locking in dma_ops path")
Reviewed-by: Filippo Sironi <sironi@amazon.de>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Joerg Roedel [Wed, 25 Sep 2019 13:22:55 +0000 (15:22 +0200)]
iommu/amd: Remove domain->updated
This struct member was used to track whether a domain
change requires updates to the device-table and IOMMU cache
flushes. The problem is, that access to this field is racy
since locking in the common mapping code-paths has been
eliminated.
Move the updated field to the stack to get rid of all
potential races and remove the field from the struct.
Fixes: 92d420ec028d ("iommu/amd: Relax locking in dma_ops path")
Reviewed-by: Filippo Sironi <sironi@amazon.de>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Linus Torvalds [Sat, 28 Sep 2019 02:37:27 +0000 (19:37 -0700)]
Merge branch 'next-integrity' of git://git./linux/kernel/git/zohar/linux-integrity
Pull integrity updates from Mimi Zohar:
"The major feature in this time is IMA support for measuring and
appraising appended file signatures. In addition are a couple of bug
fixes and code cleanup to use struct_size().
In addition to the PE/COFF and IMA xattr signatures, the kexec kernel
image may be signed with an appended signature, using the same
scripts/sign-file tool that is used to sign kernel modules.
Similarly, the initramfs may contain an appended signature.
This contained a lot of refactoring of the existing appended signature
verification code, so that IMA could retain the existing framework of
calculating the file hash once, storing it in the IMA measurement list
and extending the TPM, verifying the file's integrity based on a file
hash or signature (eg. xattrs), and adding an audit record containing
the file hash, all based on policy. (The IMA support for appended
signatures patch set was posted and reviewed 11 times.)
The support for appended signature paves the way for adding other
signature verification methods, such as fs-verity, based on a single
system-wide policy. The file hash used for verifying the signature and
the signature, itself, can be included in the IMA measurement list"
* 'next-integrity' of git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity:
ima: ima_api: Use struct_size() in kzalloc()
ima: use struct_size() in kzalloc()
sefltest/ima: support appended signatures (modsig)
ima: Fix use after free in ima_read_modsig()
MODSIGN: make new include file self contained
ima: fix freeing ongoing ahash_request
ima: always return negative code for error
ima: Store the measurement again when appraising a modsig
ima: Define ima-modsig template
ima: Collect modsig
ima: Implement support for module-style appended signatures
ima: Factor xattr_verify() out of ima_appraise_measurement()
ima: Add modsig appraise_type option for module-style appended signatures
integrity: Select CONFIG_KEYS instead of depending on it
PKCS#7: Introduce pkcs7_get_digest()
PKCS#7: Refactor verify_pkcs7_signature()
MODSIGN: Export module signature definitions
ima: initialize the "template" field with the default template
Linus Torvalds [Sat, 28 Sep 2019 00:00:27 +0000 (17:00 -0700)]
Merge tag 'nfsd-5.4' of git://linux-nfs.org/~bfields/linux
Pull nfsd updates from Bruce Fields:
"Highlights:
- Add a new knfsd file cache, so that we don't have to open and close
on each (NFSv2/v3) READ or WRITE. This can speed up read and write
in some cases. It also replaces our readahead cache.
- Prevent silent data loss on write errors, by treating write errors
like server reboots for the purposes of write caching, thus forcing
clients to resend their writes.
- Tweak the code that allocates sessions to be more forgiving, so
that NFSv4.1 mounts are less likely to hang when a server already
has a lot of clients.
- Eliminate an arbitrary limit on NFSv4 ACL sizes; they should now be
limited only by the backend filesystem and the maximum RPC size.
- Allow the server to enforce use of the correct kerberos credentials
when a client reclaims state after a reboot.
And some miscellaneous smaller bugfixes and cleanup"
* tag 'nfsd-5.4' of git://linux-nfs.org/~bfields/linux: (34 commits)
sunrpc: clean up indentation issue
nfsd: fix nfs read eof detection
nfsd: Make nfsd_reset_boot_verifier_locked static
nfsd: degraded slot-count more gracefully as allocation nears exhaustion.
nfsd: handle drc over-allocation gracefully.
nfsd: add support for upcall version 2
nfsd: add a "GetVersion" upcall for nfsdcld
nfsd: Reset the boot verifier on all write I/O errors
nfsd: Don't garbage collect files that might contain write errors
nfsd: Support the server resetting the boot verifier
nfsd: nfsd_file cache entries should be per net namespace
nfsd: eliminate an unnecessary acl size limit
Deprecate nfsd fault injection
nfsd: remove duplicated include from filecache.c
nfsd: Fix the documentation for svcxdr_tmpalloc()
nfsd: Fix up some unused variable warnings
nfsd: close cached files prior to a REMOVE or RENAME that would replace target
nfsd: rip out the raparms cache
nfsd: have nfsd_test_lock use the nfsd_file cache
nfsd: hook up nfs4_preprocess_stateid_op to the nfsd_file cache
...
Linus Torvalds [Fri, 27 Sep 2019 22:54:24 +0000 (15:54 -0700)]
Merge tag 'virtio-fs-5.4' of git://git./linux/kernel/git/mszeredi/fuse
Pull fuse virtio-fs support from Miklos Szeredi:
"Virtio-fs allows exporting directory trees on the host and mounting
them in guest(s).
This isn't actually a new filesystem, but a glue layer between the
fuse filesystem and a virtio based back-end.
It's similar in functionality to the existing virtio-9p solution, but
significantly faster in benchmarks and has better POSIX compliance.
Further permformance improvements can be achieved by sharing the page
cache between host and guest, allowing for faster I/O and reduced
memory use.
Kata Containers have been including the out-of-tree virtio-fs (with
the shared page cache patches as well) since version 1.7 as an
experimental feature. They have been active in development and plan to
switch from virtio-9p to virtio-fs as their default solution. There
has been interest from other sources as well.
The userspace infrastructure is slated to be merged into qemu once the
kernel part hits mainline.
This was developed by Vivek Goyal, Dave Gilbert and Stefan Hajnoczi"
* tag 'virtio-fs-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
virtio-fs: add virtiofs filesystem
virtio-fs: add Documentation/filesystems/virtiofs.rst
fuse: reserve values for mapping protocol
Linus Torvalds [Fri, 27 Sep 2019 22:10:34 +0000 (15:10 -0700)]
Merge tag '9p-for-5.4' of git://github.com/martinetd/linux
Pull 9p updates from Dominique Martinet:
"Some of the usual small fixes and cleanup.
Small fixes all around:
- avoid overlayfs copy-up for PRIVATE mmaps
- KUMSAN uninitialized warning for transport error
- one syzbot memory leak fix in 9p cache
- internal API cleanup for v9fs_fill_super"
* tag '9p-for-5.4' of git://github.com/martinetd/linux:
9p/vfs_super.c: Remove unused parameter data in v9fs_fill_super
9p/cache.c: Fix memory leak in v9fs_cache_session_get_cookie
9p: Transport error uninitialized
9p: avoid attaching writeback_fid on mmap with type PRIVATE
Linus Torvalds [Fri, 27 Sep 2019 20:08:36 +0000 (13:08 -0700)]
Merge tag 'riscv/for-v5.4-rc1-b' of git://git./linux/kernel/git/riscv/linux
Pull more RISC-V updates from Paul Walmsley:
"Some additional RISC-V updates.
This includes one significant fix:
- Prevent interrupts from being unconditionally re-enabled during
exception handling if they were disabled in the context in which
the exception occurred
Also a few other fixes:
- Fix a build error when sparse memory support is manually enabled
- Prevent CPUs beyond CONFIG_NR_CPUS from being enabled in early boot
And a few minor improvements:
- DT improvements: in the FU540 SoC DT files, improve U-Boot
compatibility by adding an "ethernet0" alias, drop an unnecessary
property from the DT files, and add support for the PWM device
- KVM preparation: add a KVM-related macro for future RISC-V KVM
support, and export some symbols required to build KVM support as
modules
- defconfig additions: build more drivers by default for QEMU
configurations"
* tag 'riscv/for-v5.4-rc1-b' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Avoid interrupts being erroneously enabled in handle_exception()
riscv: dts: sifive: Drop "clock-frequency" property of cpu nodes
riscv: dts: sifive: Add ethernet0 to the aliases node
RISC-V: Export kernel symbols for kvm
KVM: RISC-V: Add KVM_REG_RISCV for ONE_REG interface
arch/riscv: disable excess harts before picking main boot hart
RISC-V: Enable VIRTIO drivers in RV64 and RV32 defconfig
RISC-V: Fix building error when CONFIG_SPARSEMEM_MANUAL=y
riscv: dts: Add DT support for SiFive FU540 PWM driver
Linus Torvalds [Fri, 27 Sep 2019 20:02:19 +0000 (13:02 -0700)]
Merge tag 'nios2-v5.4-rc1' of git://git./linux/kernel/git/lftan/nios2
Pull nios2 fix from Ley Foon Tan:
"Make sure the command line buffer is NUL-terminated"
* tag 'nios2-v5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/lftan/nios2:
nios2: force the string buffer NULL-terminated
Linus Torvalds [Fri, 27 Sep 2019 19:44:26 +0000 (12:44 -0700)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull more KVM updates from Paolo Bonzini:
"x86 KVM changes:
- The usual accuracy improvements for nested virtualization
- The usual round of code cleanups from Sean
- Added back optimizations that were prematurely removed in 5.2 (the
bare minimum needed to fix the regression was in 5.3-rc8, here
comes the rest)
- Support for UMWAIT/UMONITOR/TPAUSE
- Direct L2->L0 TLB flushing when L0 is Hyper-V and L1 is KVM
- Tell Windows guests if SMT is disabled on the host
- More accurate detection of vmexit cost
- Revert a pvqspinlock pessimization"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (56 commits)
KVM: nVMX: cleanup and fix host 64-bit mode checks
KVM: vmx: fix build warnings in hv_enable_direct_tlbflush() on i386
KVM: x86: Don't check kvm_rebooting in __kvm_handle_fault_on_reboot()
KVM: x86: Drop ____kvm_handle_fault_on_reboot()
KVM: VMX: Add error handling to VMREAD helper
KVM: VMX: Optimize VMX instruction error and fault handling
KVM: x86: Check kvm_rebooting in kvm_spurious_fault()
KVM: selftests: fix ucall on x86
Revert "locking/pvqspinlock: Don't wait if vCPU is preempted"
kvm: nvmx: limit atomic switch MSRs
kvm: svm: Intercept RDPRU
kvm: x86: Add "significant index" flag to a few CPUID leaves
KVM: x86/mmu: Skip invalid pages during zapping iff root_count is zero
KVM: x86/mmu: Explicitly track only a single invalid mmu generation
KVM: x86/mmu: Revert "KVM: x86/mmu: Remove is_obsolete() call"
KVM: x86/mmu: Revert "Revert "KVM: MMU: reclaim the zapped-obsolete page first""
KVM: x86/mmu: Revert "Revert "KVM: MMU: collapse TLB flushes when zap all pages""
KVM: x86/mmu: Revert "Revert "KVM: MMU: zap pages in batch""
KVM: x86/mmu: Revert "Revert "KVM: MMU: add tracepoint for kvm_mmu_invalidate_all_pages""
KVM: x86/mmu: Revert "Revert "KVM: MMU: show mmu_valid_gen in shadow page related tracepoints""
...
Linus Torvalds [Fri, 27 Sep 2019 19:19:47 +0000 (12:19 -0700)]
Merge tag 'pwm/for-5.4-rc1' of git://git./linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"Besides one new driver being added for the PWM controller found in
various Spreadtrum SoCs, this series of changes brings a slew of,
mostly minor, fixes and cleanups for existing drivers, as well as some
enhancements to the core code.
Lastly, Uwe is added to the PWM subsystem entry of the MAINTAINERS
file, making official his role as a reviewer"
* tag 'pwm/for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (34 commits)
MAINTAINERS: Add myself as reviewer for the PWM subsystem
MAINTAINERS: Add patchwork link for PWM entry
MAINTAINERS: Add a selection of PWM related keywords to the PWM entry
pwm: mediatek: Add MT7629 compatible string
dt-bindings: pwm: Update bindings for MT7629 SoC
pwm: mediatek: Update license and switch to SPDX tag
pwm: mediatek: Use pwm_mediatek as common prefix
pwm: mediatek: Allocate the clks array dynamically
pwm: mediatek: Remove the has_clks field
pwm: mediatek: Drop the check for of_device_get_match_data()
pwm: atmel: Consolidate driver data initialization
pwm: atmel: Remove unneeded check for match data
pwm: atmel: Remove platform_device_id and use only dt bindings
pwm: stm32-lp: Add check in case requested period cannot be achieved
pwm: Ensure pwm_apply_state() doesn't modify the state argument
pwm: fsl-ftm: Don't update the state for the caller of pwm_apply_state()
pwm: sun4i: Don't update the state for the caller of pwm_apply_state()
pwm: rockchip: Don't update the state for the caller of pwm_apply_state()
pwm: Let pwm_get_state() return the last implemented state
pwm: Introduce local struct pwm_chip in pwm_apply_state()
...
projects / openwrt / staging / blogic.git / log