Martin Garbe [Tue, 13 Feb 2024 06:49:05 +0000 (07:49 +0100)]
ath79: update WA/XC devices UBNT_VERSION to 8.7.4
Ubiquiti WA devices with newer hw version (sold 2023)
require UBNT_VERSION to be at least 8.7.4, otherwise
the image is rejected.
For consistency, also increase version number for XC devices.
Signed-off-by: Martin Garbe <monomartin@opennet-initiative.de>
Tianling Shen [Fri, 16 Feb 2024 06:34:40 +0000 (14:34 +0800)]
rockchip: add NanoPi R2C Plus support
The NanoPi R2C Plus is a small variant of NanoPi R2C with a on-board
eMMC flash (8G) included.
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Tianling Shen [Fri, 16 Feb 2024 06:33:49 +0000 (14:33 +0800)]
uboot-rockchip: add NanoPi R2C Plus support
Add support for the FriendlyARM NanoPi R2C Plus.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Chukun Pan [Mon, 15 Jan 2024 15:28:13 +0000 (23:28 +0800)]
qualcommax: backport more changes for ipq6018 and ipq8074
- Mark patches as upstream
- Backport more upstream changes
- Handle conflicts and refresh patches
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Rafał Miłecki [Wed, 14 Feb 2024 15:05:19 +0000 (16:05 +0100)]
base-files: sysupgrade: include uci-defaults script disabling services
Disabled services should be kept disabled after sysupgrade. This can be
easily handled using a proper uci-defaults script.
Extend sysupgrade to check for disabled services, generate uci-defaults
script disabling them and include it in backup.
Cc: Christian Marangi <ansuelsmth@gmail.com>
Cc: Jo-Philipp Wich <jo@mein.io>
Cc: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Jo-Philipp Wich <jo@mein.io>
Rafał Miłecki [Tue, 13 Feb 2024 21:10:37 +0000 (22:10 +0100)]
base-files: sysupgrade: always setup overlay when creating backup
Setting overlay while creating backup allows including extra files in
archive without actually writing them to flash. Right now this feature
is limited to /etc/backup/ directory and is used only for including
installed_packages.txt.
Extend this solution to make it more generic:
1. Always mount overlay while creating backup
2. Overlay whole / to don't limit it to /etc/backup/
This allows including any additional files in backups and adding more
sysupgrade features.
Cc: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Cc: Christian Marangi <ansuelsmth@gmail.com>
Cc: Jo-Philipp Wich <jo@mein.io>
Cc: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Luiz Angelo Daros de Luca [Thu, 20 Oct 2022 02:27:52 +0000 (23:27 -0300)]
base-files: sysupgrade: always cleanup after backups
When tar was failing, it was exiting immediately. Some files and the
tmpfs mount (-k) would remain breaking the next backup attempt.
Also remove redundant $? from exit builtin call as exit already returns
the last command exit code when called.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Luiz Angelo Daros de Luca [Thu, 20 Oct 2022 02:12:49 +0000 (23:12 -0300)]
base-files: sysupgrade: do not hide tar errors
tar stderr was probably discarded only to remove this message:
tar: removing leading '/' from member names
However, together with that, any other error would also be discarded.
It is easier to fix that allowing the error message to be printed.
In sysupgrade, the backup file list only uses absolute paths. That way,
the solution is to remove the leading '/' from all files (sed) and chdir
to / (option -C /)
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Rafał Miłecki [Mon, 19 Feb 2024 05:36:37 +0000 (06:36 +0100)]
mediatek: filogic: move mt7981 on-SoC blocks to "soc" node in DT
It's a standard way of grouping on-SoC hardware blocks and this matches
upstream DTS.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Daniel Golle [Sun, 18 Feb 2024 05:02:38 +0000 (05:02 +0000)]
mediatek: filogic: fix nvmem cell names of the GL.iNet MT-2500
Fix style of nvmem cell names in the device tree of the GL.iNet MT-2500.
Fixes: 49ed52b862 ("mediatek: filogic: convert GL.iNet MT-2500 to use NVMEM-on-MMC)"
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Janusz Dziedzic [Thu, 1 Feb 2024 08:37:54 +0000 (09:37 +0100)]
linux-firmware: intel: add BE200 wifi firmware
Add option to install Intel BE200 firmware
required by iwlwifi driver and Wifi7 hardware.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Koen Vandeputte [Tue, 13 Feb 2024 10:18:16 +0000 (11:18 +0100)]
imx: remove 5.15 support
Drop all 5.15 files as 6.1 is the default now
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
Koen Vandeputte [Tue, 13 Feb 2024 10:18:03 +0000 (11:18 +0100)]
imx: switch to kernel 6.1
I have this kernel running for weeks some
on a lot of boards in multiple scenarios
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
John Audia [Fri, 16 Feb 2024 21:57:53 +0000 (16:57 -0500)]
kernel: bump 6.1 to 6.1.78
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.78
Manually rebased:
bcm27xx/patches-6.1/950-0865-usb-dwc3-Set-DMA-and-coherent-masks-early.patch
bcm27xx/patches-6.1/950-0124-Add-support-for-all-the-downstream-rpi-sound-card-dr.patch
All other patches automatically rebased.
Build system: x86/64
Build-tested: x86/64/AMD Cezanne, ramips/tplink_archer-a6-v3, logic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: x86/64/AMD Cezanne, ramips/tplink_archer-a6-v3, logic/xiaomi_redmi-router-ax6000-ubootmod
Signed-off-by: John Audia <therealgraysky@proton.me>
Stefan Kalscheuer [Sat, 17 Feb 2024 16:59:08 +0000 (17:59 +0100)]
mvebu: drop kernel 5.15 config and patches
With default now being at 6.1 we can remove all 5.15 components.
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
Stefan Kalscheuer [Sat, 17 Feb 2024 16:55:43 +0000 (17:55 +0100)]
mvebu: switch to kernel 6.1
After a few months of testing it's time to move to 6.1 by default.
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
Seo Suchan [Sat, 17 Feb 2024 23:58:54 +0000 (08:58 +0900)]
ca-certificates: update to version
20240203
Update Mozilla certificate authority bundle to version 2.64
Signed-off-by: Seo Suchan <tjtncks@gmail.com>
Bjørn Mork [Sat, 17 Feb 2024 14:03:40 +0000 (15:03 +0100)]
realtek: fix Netgear GS110TPP OEM install
Recent OEM firmware versions test the version number embedded in the uimage
"name" header field. The exact restricton is unknown, but "7.0.8.4" seems
to be the lowest number accepted on a GS110TPPv1 which already has that
version or higher.
A "9.9.9.9" version is accepted as valid by the GS110TPPv1 OEM firmware,
and considered both unique enough to identify an OpenWrt image and
moderately future proof against OEM version bumps.
This change is also boot tested on a GS108Tv3 with
"BOOT Loader Version 1.0.0.2 (2018-08-31 17:05:26 UTC)"
to verify that it doesn't break boot on older hardware.
Link: https://forum.openwrt.org/t/72510/58
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Daniel Golle [Sat, 17 Feb 2024 22:22:28 +0000 (22:22 +0000)]
mediatek: filogic: convert GL.iNet MT-2500 to use NVMEM-on-MMC
Use nvmem-layout in device tree instead of extracting MAC addresses
in userspace.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sun, 18 Feb 2024 03:13:23 +0000 (03:13 +0000)]
mediatek: mt7981: remove inaccurate compatible strings
Remove more inaccurate compatible strings from various clock controllers
of the MT7981 SoC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sun, 18 Feb 2024 03:12:01 +0000 (03:12 +0000)]
mediatek: mt7981: prevent system freezes on boot
Import patch to make sure SGM_REG_SEL clock is always enabled as it
seems that more registers than just SGMIISYS0 and SGMIISYS1 are
depending on that clock being enabled.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sat, 17 Feb 2024 22:14:01 +0000 (22:14 +0000)]
mediatek: filogic: convert GL.iNet MT-6000 to NVMEM-on-MMC
Now that we can reference MMC partitions in device tree, use that
to get rid of Wi-Fi EEPROM and MAC address setup in userspace.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sun, 18 Feb 2024 01:02:46 +0000 (01:02 +0000)]
kernel: nvmem: correctly assign fwnode to MMC block device
Use device_set_node to make sure OF node gets assigned on block
devices to be used as NVMEM providers. While block partitions were
already working fine as NVMEM providers, bare block devices such as
mmcblk0boot1 will not work without this change.
Fixes: fc153aa8d9 ("kernel: import pending patches adding support for NVMEM on UBI and MMC")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Robert Marko [Sat, 17 Feb 2024 16:44:20 +0000 (17:44 +0100)]
qualcommax: ipq807x: wax630: correct UNIPHY2 MAC mode
UNIPHY2 on the WAX630 is connected to a QCA8081 PHY which is only 2.5G and
it does not support using USXGMII at all but rather only SGMII or SGMII+.
Tested-by: Kristian Skramstad <kristian+github@83.no>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Daniel Golle [Sat, 17 Feb 2024 17:54:05 +0000 (17:54 +0000)]
mediatek: dts: mt7981: fix ethsys clock compatible
Remove inaccurate compatible string 'mediatek,mt7986-ethsys' which
results in the wrong clock driver probing on MT7981 with Linux 6.1 and
ends up freezing the system once WED is used.
Fixes: da970d63fb ("mediatek: switch to Linux version 6.1")
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Rafał Miłecki [Wed, 17 Jan 2024 21:20:15 +0000 (22:20 +0100)]
mediatek: filogic: replace built-in Aquantia driver with module
Some Aquantia PHYs (e.g. AQR113C) require firmware to be uploaded by
host system. With built-in drivers this doesn't work in OpenWrt /
embeddded as filesystem isn't available during PHY probe. That results
in delays like:
[ 1.588068] Aquantia AQR113C mdio-bus:00: Falling back to sysfs fallback for: Rhe-05.06-Candidate9-AQR_Mediatek_23B_P5_ID45824_LCLVER1.cld
[ 64.526387] Aquantia AQR113C mdio-bus:00: failed to find FW file Rhe-05.06-Candidate9-AQR_Mediatek_23B_P5_ID45824_LCLVER1.cld (-110)
Switch to module to postpone PHY probe to init state.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Robert Marko [Sat, 17 Feb 2024 16:39:22 +0000 (17:39 +0100)]
qualcommax: ipq807x: correct PHY mode for AQR
Interfaces that have AQR-s attached to them are using USXGMII and not just
the default SGMII.
This was fine until SSDK added some sanity checking and now on Qnap 301W it
would fail with:
[ 24.740197] nss-dp
3a001800.dp5 10g-1 (uninitialized): failed to connect to phy device
[ 24.740264] nss-dp: probe of
3a001800.dp5 failed with error -14
Since this is not Qnap 301W specific lets fix it subtarget wide by
declaring the correct PHY mode for 10G AQR-s.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Robert Marko [Sat, 17 Feb 2024 12:41:36 +0000 (13:41 +0100)]
qualcommax: ipq807x: 301w: correct PHY mode for AQR
Interfaces that have AQR-s attached to them are using USXGMII and not just
the default SGMII.
This was fine until SSDK added some sanity checking and now on Qnap 301W it
would fail with:
[ 24.740197] nss-dp
3a001800.dp5 10g-1 (uninitialized): failed to connect to phy device
[ 24.740264] nss-dp: probe of
3a001800.dp5 failed with error -14
So, lets fix 10G AQR ports by declaring the correct PHY mode.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Daniel Golle [Sat, 17 Feb 2024 14:22:31 +0000 (14:22 +0000)]
mediatek: mt7622: skip build also for Xiaomi AX6S
Also here build fails due to increased kernel size.
Fixes: da970d63fb ("mediatek: switch to Linux version 6.1")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Paul Spooren [Mon, 12 Feb 2024 15:59:50 +0000 (16:59 +0100)]
build: align SOURCE path for build system and SDK
Building a package in the build system or the SDK results in different
values for the `SOURCE` property, it's either `packages/<package name>`
or `feeds/base/<package name>`. The reason is that the SDK handles
`openwrt.git` as an external feed called while the build system contains
the *base* packages directly.
Since packages created with either method are (ideally) the same (bit
for bit), align the content of SOURCE. To do so this commit creates a
symlink from `feeds/base` to `$(TOPDIR)/package` and adopts the SOURCE
when building from inside the build system.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Eneas U de Queiroz [Sat, 3 Feb 2024 19:33:14 +0000 (16:33 -0300)]
wifi-scripts: fix FILS AKM selection with EAP-192
Fix netifd hostapd.sh selection of FILS-SHA384 algorithm with eap-192.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Daniel Golle [Sat, 17 Feb 2024 04:26:00 +0000 (04:26 +0000)]
mediatek: mt7622: skip build for MT7622 rfb1 (UBI)
Due to increased kernel size the build currently fails if including
the MT7622 rfb1 (UBI). Skip it for now until there is a better
solution (such as replacing the bootloader and changing the flash
layout).
Fixes: da970d63fb ("mediatek: switch to Linux version 6.1")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sat, 17 Feb 2024 01:23:34 +0000 (01:23 +0000)]
mediatek: filogic: bpi-r3-mini: include kmod-phy-airoha-en8811h
Include the needed Ethernet PHY driver module for the BananaPi R3 mini.
Fixes: b03d3644cf ("mediatek: filogic: add BananaPi BPi-R3 mini")
Reported-by: BPI forum user nezar_taima
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Rosen Penev [Sun, 11 Feb 2024 02:13:10 +0000 (18:13 -0800)]
lua5.3: backport CVE fix
Also refreshed some patches
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Sun, 11 Feb 2024 23:06:44 +0000 (15:06 -0800)]
lua: fix CVE-2014-5461
Patch taken from Debian.
Refresh patches
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Daniel Golle [Fri, 16 Feb 2024 13:55:12 +0000 (13:55 +0000)]
images: append to existing image with ubinize-image build cmd
Let ubinize-image append the ubinized image to the existing image
instead of replacing it.
Fixes: 6c17d71973 ("scripts: ubinize-image.sh: support static volumes, make size optional")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Tianling Shen [Fri, 16 Feb 2024 05:37:17 +0000 (13:37 +0800)]
mediatek: filogic: bpi-r3-mini: fix power on M.2 slot
One of the pins requiered by M.2 slot is conflict with spi1,
however, spi1 seems unused so simply disable it for now, this
matches the factory behavior [1].
1. https://github.com/BPI-SINOVOIP/BPI-R3MINI-OPENWRT-V21.02.3/commit/
9bd78779f267a21c04c5bb4d16c32e83aae8d1d3
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Tianling Shen [Fri, 16 Feb 2024 05:29:44 +0000 (13:29 +0800)]
mediatek: filogic: bpi-r3-mini: bind WLAN LED-s to phy*-ap0
For showing wlan status.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Tianling Shen [Fri, 16 Feb 2024 05:26:51 +0000 (13:26 +0800)]
mediatek: filogic: bpi-r3-mini: convert to new LED color/function format
Conversion to new LED color/function format and drop label format.
This was needed previously when the new format wasn't supported by
leds.sh functions script. Now that is supported this property can be
removed in favor of the new format.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Daniel Golle [Fri, 16 Feb 2024 05:47:53 +0000 (05:47 +0000)]
uboot-mediatek: bpi-r3-mini: fix typo in bootmenu
Fix typo in eMMC bootmenu.
Fixes: bc25519f98 ("uboot-mediatek: add builds for BananaPi BPi-R3 mini")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Foica David [Wed, 14 Feb 2024 21:32:27 +0000 (23:32 +0200)]
ath79: generic: fix the alphabetical order in 02_network
This commit fixes the alphabetical order in 02_network.
The 2 deco devices in ath79_setup_interfaces() were in the wrong place.
Signed-off-by: Foica David <superh552@gmail.com>
Chukun Pan [Tue, 30 Jan 2024 15:25:27 +0000 (23:25 +0800)]
qualcommax: AW1000: add qca8081 PHY LED configuration
Since we can configure the PHY LED of the qca8081,
add a configuration for this device.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Chukun Pan [Mon, 12 Feb 2024 15:18:30 +0000 (23:18 +0800)]
qualcommax: AW1000: sync qca807x PHY dts changes
The dts of Arcadyan AW1000 forgot to convert qca807x PHY
to PHY package implementation. This commit fix it.
Fixes: 0ab4b92 ("qualcommax: convert qca807x PHY to PHY package implementation")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Justin Klaassen [Thu, 18 Jan 2024 15:36:22 +0000 (15:36 +0000)]
build: fix opkg flags in rootfs
By default opkg sets the "user" flag when a package is installed,
which resulted in most packages in the rootfs having this flag
set incorrectly. This patch removes the "user" flag from all
installed packages when preparing the rootfs image.
Fixes: #14427
Signed-off-by: Justin Klaassen <justin@tidylabs.app>
Daniel Golle [Fri, 16 Feb 2024 05:36:26 +0000 (05:36 +0000)]
mediatek: filogic: bpi-r3-mini: fix generating ubinized image
Generate ubinized image as ARTIFACT and make use of now available
generic 'ubinize-image' build step intended for that purpose.
Fixes: b03d3644cf ("mediatek: filogic: add BananaPi BPi-R3 mini")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 16 Feb 2024 05:38:07 +0000 (05:38 +0000)]
mediatek: filogic: bpi-r3-mini: fix NAND flash layout
Fix NAND flash layout which was out-of-sync with the definition in
ARM TrustedFirmware-A which expects UBI to start at 0x200000.
Fixes: b03d3644cf ("mediatek: filogic: add BananaPi BPi-R3 mini")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 16 Feb 2024 05:32:51 +0000 (05:32 +0000)]
scripts: ubinize-image.sh: fix on POSIX shell, allow custom images
Make sure ubinize-image.sh also works with more simple POSIX Shell and
allow creating complete custom images to be used as ARTIFACT/foo.img
and thereby allow including uImage.FIT, TF-A FIP and what ever else
is required on a specific board.
Fixes: 6c17d71973 ("scripts: ubinize-image.sh: support static volumes, make size optional")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 16 Feb 2024 05:18:47 +0000 (05:18 +0000)]
ramips: mt76x8: fix build due to renamed U-Boot binary
The U-Boot binary for the RAVPower RP-WD009 has been renamed.
In order to be uniform with all other U-Boot binaries generated the SoC type has been prepended.
Set that new name also in the image build recipe for that device in order to fix build.
Fixes: 927334a8f7 ("uboot-mediatek: add basic build for ZBT-WG3526 (MT7621, 16M SPI-NOR)")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Tim Harvey [Wed, 15 Mar 2023 19:58:33 +0000 (12:58 -0700)]
imx: update default network config for ventana
update the default network configuration for Gateworks Ventana boards
such that the left-most front-panel NIC is WAN and any additional are in
LAN bridge
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Wed, 15 Mar 2023 19:56:56 +0000 (12:56 -0700)]
imx: add gpio-button-hotplug to ventana images
Add the gpio-button-hotplug to Gateworks ventana images to support
the on-board user pushbutton.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Daniel Golle [Fri, 26 Jan 2024 17:28:01 +0000 (17:28 +0000)]
mediatek: filogic: add BananaPi BPi-R3 mini
Hardware specification
----------------------
SoC: MediaTek MT7986A 4x A53
Flash: 128MB SPI-NAND, 8GB eMMC
RAM: 2GB DDR4
Ethernet: 2x 2.5GbE (Airoha EN8811H)
WiFi: MediaTek MT7976C 2x2 2.4G + 3x3 5G
Interfaces:
* M.2 Key-M: PCIe 2.0 x2 for NVMe SSD
* M.2 Key-B: USB 3.0 with SIM slot
* front USB 2.0 port
LED: Power, Status, WLAN2G, WLAN5G, LTE, SSD
Button: Reset, internal boot switch
Fan: PWM-controlled 5V fan
Power: 12V Type-C PD
Installation instructions for eMMC
----------------------------------
0. Set boot switch to boot from SPI-NAND (assuming stock rom or immortalwrt
running there).
1. Write GPT partition table to eMMC
Move openwrt-mediatek-filogic-bananapi_bpi-r3-mini-emmc-gpt.bin to
the device /tmp using scp and write it to /dev/mmcblk0:
dd if=/tmp/openwrt-*-r3-mini-emmc-gpt.bin of=/dev/mmcblk0
2. Reboot (to reload partition table)
3. Write bootloader and OpenWrt images
Move files to the device /tmp using scp:
- openwrt-*-bananapi_bpi-r3-mini-emmc-preloader.bin
- openwrt-*-bananapi_bpi-r3-mini-emmc-bl31-uboot.fip
- openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb
- openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb
Write them to the appropriate partitions:
echo 0 > /sys/block/mmcblk0boot0/force_ro
dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-emmc-preloader.bin of=/dev/mmcblk0boot0
dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-emmc-bl31-uboot.fip of=/dev/mmcblk0p3
dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb of=/dev/mmcblk0p4
dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb of=/dev/mmcblk0p5
sync
4. Remove the device from power, set boot switch to eMMC and boot into
OpenWrt. The device will come up with IP 192.168.1.1 and assume the
Ethernet port closer to the USB-C power connector as LAN port.
5. If you like to have Ethernet support inside U-Boot (eg. to boot via
TFTP) you also need to write the PHY firmware to /dev/mmcblk0boot1:
echo 0 > /sys/block/mmcblk0boot1/force_ro
dd if=/lib/firmware/airoha/EthMD32.dm.bin of=/dev/mmcblk0boot1
dd if=/lib/firmware/airoha/EthMD32.DSP.bin bs=16384 seek=1 of=/dev/mmcblk0boot1
Installation instructions for NAND
----------------------------------
0. Set boot switch to boot from eMMC (assuming OpenWrt is installed there
by instructions above. Using stock rom or immortalwrt does NOT work!)
1. Write things to NAND
Move files to the device /tmp using scp:
- openwrt-*-bananapi_bpi-r3-mini-snand-preloader.bin
- openwrt-*-bananapi_bpi-r3-mini-snand-bl31-uboot.fip
- openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb
- openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb
Write them to the appropriate locations:
mtd write /tmp/openwrt-*-bananapi_bpi-r3-mini-snand-preloader.bin /dev/mtd0
ubidetach -m 1
ubiformat /dev/mtd1
ubiattach -m 1
volsize=$(wc -c < /tmp/openwrt-*-bananapi_bpi-r3-mini-snand-bl31-uboot.fip)
ubimkvol /dev/ubi0 -N fip -n 0 -s $volsize -t static
ubiupdatevol /dev/ubi0_0 /tmp/openwrt-*-bananapi_bpi-r3-mini-snand-bl31-uboot.fip
cd /lib/firmware/airoha
cat EthMD32.dm.bin EthMD32.DSP.bin > /tmp/en8811h-fw.bin
ubimkvol /dev/ubi0 -N en8811h-firmware -n 1 -s 147456 -t static
ubiupdatevol /dev/ubi0_1 /tmp/en8811h-fw.bin
ubimkvol /dev/ubi0 -n 2 -N ubootenv -s 126976
ubimkvol /dev/ubi0 -n 3 -N ubootenv2 -s 126976
volsize=$(wc -c < /tmp/openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb)
ubimkvol /dev/ubi0 -n 4 -N recovery -s $volsize
ubiupdatevol /dev/ubi0_4 /tmp/openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb
volsize=$(wc -c < /tmp/openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb)
ubimkvol /dev/ubi0 -n 4 -N recovery -s $volsize
ubiupdatevol /dev/ubi0_4 /tmp/openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb
3. Remove the device from power, set boot switch to NAND, power up and
boot into OpenWrt.
Partially based on immortalwrt support for the R3 mini, big thanks for
doing the ground work!
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 26 Jan 2024 17:27:08 +0000 (17:27 +0000)]
kernel: add driver for Airoha EN8811H PHY as module
Add PHY driver for Airoha EN8811H PHY and package it as kernel module.
The PHY needs to load firmware from rootfs, so there is no point in
having the driver built-into the kernel.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 26 Jan 2024 17:26:39 +0000 (17:26 +0000)]
uboot-mediatek: add builds for BananaPi BPi-R3 mini
The R3 mini comes with two Airoha EN8811H PHYs for 2.5G Ethernet.
The driver added to U-Boot expects the firmware for the PHY to be
stored inside UBI volume en8811h-fw or MMC boot1 hardware partition.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 26 Jan 2024 17:29:22 +0000 (17:29 +0000)]
linux-firmware: package firmware for Airoha EN8811H PHY
Add package with firmware for Airoha EN8811H 2.5G Ethernet PHY which
needs to be loaded via MDIO before the PHY can be used.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Thu, 1 Feb 2024 05:03:56 +0000 (05:03 +0000)]
scripts: ubinize-image.sh: support static volumes, make size optional
In order to support devices having TF-A FIP image or UBI-aware U-Boot
SPL we need to include a static volume for the bootloader.
Introduce support for adding additional static volumes by prefixing
the filename with ':', eg.
UBINIZE_PARTS := fip:=$(STAGING_DIR_IMAGE)/u-boot.fip
Also add support for rootfs-in-uImage.FIT setups which don't require a
rootfs partition and make the (3rd) size parameter in UBINIZE_PARTS
optional (see example above without declared size).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Wed, 24 Jan 2024 19:10:36 +0000 (19:10 +0000)]
mediatek: update driver for MT7988 built-in 2.5G Ethernet PHY
Sync driver for built-in 2.5G Ethernet PHY with MediaTek SDK.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Mon, 8 Jan 2024 21:08:13 +0000 (21:08 +0000)]
firmware: package firmware for built-in 2.5G PHY on MT7988
Firmware for the built-in 2.5G Ethernet PHY of the MediaTek MT7988 SoC
is now part of linux-firmware, so we can package it.
Only a single file is needed with recent driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Mon, 22 Jan 2024 19:12:40 +0000 (19:12 +0000)]
mediatek: mt7622: modernize Linksys E8450 / Belkin RT3200 UBI build
Move fip and factory into UBI static volumes.
Use fitblk instead of partition parser.
!! RUN INSTALLER FIRST !!
Existing users of previous OpenWrt releases or snapshot builds will
have to **re-run the updated installer** before upgrading to firmware
after this commit.
DO NOT flash or run even just the initramfs image unless you have
run the updated installer which moves the content of the 'factory'
partition into a UBI volume.
tl;dr: DON'T USE YET!
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Mon, 22 Jan 2024 00:56:47 +0000 (00:56 +0000)]
mediatek: mt7622: convert unifi6lr-v{1,2,3}-ubootmod to fitblk
No bootloader changes needed in this case, smooth transition.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sun, 21 Jan 2024 23:50:02 +0000 (23:50 +0000)]
mediatek: mt7622: convert BPi-R64 to all-UBI layout and fitblk
Modernize bootloader and flash memory layout of the BPi-R64 similar to
how it has also been done for the BPi-R3.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sat, 20 Jan 2024 16:24:59 +0000 (16:24 +0000)]
arm-trusted-firmware-mediatek: add UBI-enabled builds for MT7622
Use custom UBI start address 0x80000 on MT7622 which is more than
enough for a single bl2 (MT7622 BootROM doesn't support redundant bl2).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Thu, 18 Jan 2024 22:15:35 +0000 (22:15 +0000)]
mediatek: BananaPi BPi-R3 bootloader update
* Switch to all-UBI layout on SPI-NAND
* use fitblk driver instead of uImage.FIT partition parser
* adapt sysupgrade
* bump COMPAT_VERSION
Remove BROKEN mark now that all needed changes are done.
Boards running images generated before this commit will require
full reflash of the bootloader, re-install from SD card is the
easiest way to achieve that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Thu, 18 Jan 2024 22:18:14 +0000 (22:18 +0000)]
uboot-envtools: mediatek_filogic: update bpi-r3
Unify env configuration now that BPi-R4 and BPi-R3 both use fitblk.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Thu, 18 Jan 2024 22:12:08 +0000 (22:12 +0000)]
uboot-mediatek: bpi-r3: all-UBI NAND layout, use fitblk
Modernize U-Boot to provide a better reference:
* store fip image in UBI now that TF-A supports that
* switch from uImage.FIT partition parser to new fitblk
virtual firmware block driver (root=/dev/fit0)
* automatically set root device according to boot_mode register
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Thu, 18 Jan 2024 22:10:42 +0000 (22:10 +0000)]
arm-trusted-firmware-mediatek: add mt7986-spim-nand-ubi-ddr4
Add UBI-enabled build for MT7986 with SPIM-NAND and DDR4 for use with
the BananaPi R3 board.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Thu, 18 Jan 2024 22:54:29 +0000 (22:54 +0000)]
mediatek: prepare BananaPi BPi-R3 for upcoming modernization
Mark board as broken until the complete boot stack has been updated.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Mon, 27 Nov 2023 04:01:33 +0000 (04:01 +0000)]
uboot-envtools: filogic: add support for BananaPi R4
Add environment settings for the BananaPi BPI-R4 router board which
can boot from (and store its bootloader environment on) micro SD card,
SPI-NAND and eMMC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Mon, 27 Nov 2023 03:59:32 +0000 (03:59 +0000)]
uboot-envtools: filogic: de-duplicate UBI env settings
Use function instead of duplicating the env settings on UBI for
OpenWrt-built U-Boot over and over.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sun, 23 Jul 2023 11:38:15 +0000 (12:38 +0100)]
mediatek: add support for BananaPi BPI-R4 board
Hardware
--------
SOC: MediaTek MT7988A (4x Cortex-A73)
RAM: 4 GiB DDR4
Flash: 128 MiB Winbond SPI-NAND
MMC: 8 GiB eMMC *or* microSD (cannot be used both)
ETH: 4x 1GE (1x WAN, 3x LAN)
2x SFP+ (10G, 5G, 2.5G, 1G)
USB: on-board USB 3.2 4-port hub
1x USB 3.2 port (type A connector)
1x M.2 for 4G/5G modem
2x mPCIe for additional modems
WiFi: optional MediaTek MT7996 Wi-Fi 7 module
(using 2x PCIe gen3 x2 on the mPCIe slots and 12V power)
Installation
------------
1. Decompress and write the sdcard image to a micro SD card and use that
to boot the R4 (both dip switches in upper position).
2. Use the bootloader menu accessible via the serial console to install
to SPI-NAND.
3. Switch to boot from SPI-NAND and install to eMMC.
Known issues
------------
- The RST button is hard-wired to the SoC reset and can't be read
from software. This can be changed by modifying the board (ie.
moving a 0-ohm resistor). However, in order to maintain compatibility
with the board as it comes from factory the button isn't used by
OpenWrt and the WPS button is used as factory/reset button instead.
- various small things still need to be fixed in DT
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Wed, 13 Dec 2023 05:37:20 +0000 (05:37 +0000)]
uboot-mediatek: update to U-Boot 2024.01 release
Rebase local patches on top of quarterly timed release, allowing to
drop numerous patches which have been accepted upstream since the
release of U-Boot 2023.07.02.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Tue, 25 Jul 2023 01:56:01 +0000 (02:56 +0100)]
uboot-mediatek: add build for BPi-R4
Add build for the BananaPi R4 board which can boot from micro SD,
SPI-NAND or eMMC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Tue, 5 Dec 2023 04:10:31 +0000 (04:10 +0000)]
uboot-mediatek: mt7988: set rootdisk according to boot device
If nodes /chosen/rootdisk-${bootdevice} exists, set /chosen/rootdisk
phandle according to boot device selected by the bootstrap pins.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Tue, 5 Dec 2023 04:08:13 +0000 (04:08 +0000)]
uboot-mediatek: fix MMC erase timeout
When erasing large amounts of blocks at once this can take a long
time on slow cards. Instead of a fixed timeout, wait longer if more
blocks are being erased.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Tue, 9 Aug 2022 22:59:50 +0000 (00:59 +0200)]
uboot-mediatek: add basic build for ZBT-WG3526 (MT7621, 16M SPI-NOR)
Add basic U-Boot drop-in replacement compatible with the flash layout
of the vendor loader of the Zbtlink WG3526 (16M) MT7621 router board.
The idea here is a to have a reference build of uboot-mediatek also for
a simple MIPS boards more popular than MT7621 RFB.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 8 Dec 2023 01:04:39 +0000 (01:04 +0000)]
mediatek: add patch for xsphy driver to support pcie2 on MT7988
Import patch from MediaTek SDK which allows using the third
PCIe host controller of the MT7988 SoC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Tue, 13 Feb 2024 05:32:49 +0000 (05:32 +0000)]
mediatek: dts: mt7988: add uart1 and uart2
Add device tree nodes for uart1 and uart2 of the MT7988 SoC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Tue, 13 Feb 2024 05:30:24 +0000 (05:30 +0000)]
mediatek: pinctrl-mt7988: add additional uart1_2_lite group
Add UART pinctrl group for using only pins 80 and 81 for uart1.
This is needed on the BPi-R4 as RTS/CTS signals are used for other
on-board functions.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Thu, 25 Jan 2024 01:22:10 +0000 (01:22 +0000)]
mediatek: pinctrl-mt7988: add pinconf map
Add pull-up/pull-down configuration for pins of MT7988.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sun, 28 Jan 2024 03:55:15 +0000 (03:55 +0000)]
mediatek: switch to pending XFI 10G Ethernet drivers
Replace previous patch adding paths and SerDes modes with patch series
pending upstream adding dedicated drivers for XFI T-PHY and USXGMII PCS,
extends LynxI PCS to be a standalone platform driver and as a consequence
makes much less changes to the actual Ethernet driver mtk_eth_soc.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sun, 28 Jan 2024 03:46:58 +0000 (03:46 +0000)]
mediatek: backport a hell of thermal commits
Backport almost 50 commits from upstream Linux to improve thermal
drivers for MediaTek SoCs and add new LVTS driver for MT7988.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sun, 28 Jan 2024 03:45:53 +0000 (03:45 +0000)]
mediatek: replace mt7988 clk files with accepted patches
Replace clock drivers for MT7988 with backported upstream commits.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sun, 28 Jan 2024 03:36:40 +0000 (03:36 +0000)]
kernel: backport phylink changes from mainline Linux
Let's pick a bunch of useful phylink changes which allow us to keep
drivers in sync with mainline Linux.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Mon, 4 Dec 2023 23:41:39 +0000 (23:41 +0000)]
mediatek: switch to Linux version 6.1
Drop support for Linux 5.15 and switch to Linux 6.1.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Tue, 13 Jun 2023 14:32:15 +0000 (15:32 +0100)]
package: add fitblk util to release /dev/fit* devices
Add minimalistic tool to allow releasing /dev/fit* devices which is
needed on sysupgrade when using the fitblk driver.
The package is hidden in menuconfig, it should only be selected by
adding it to the default package selection of boards using it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Tue, 5 Dec 2023 00:20:42 +0000 (00:20 +0000)]
kernel: add pending fitblk uImage.FIT sub-image block driver
Add 'fitblk' driver to replace the rejected/deprecated uImage.FIT
partition parser.
To use the new driver, add phandle /chosen/rootdisk and point it to
the MTD partition, UBI volume or block device holding the uImage.FIT.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Mon, 4 Dec 2023 23:48:40 +0000 (23:48 +0000)]
kernel: import pending patches adding support for NVMEM on UBI and MMC
Similar to supporting nvmem-layouts on MTD devices, also allow referencing
UBI and MMC devices in DT.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 24 Nov 2023 12:22:27 +0000 (12:22 +0000)]
kernel: allow skipping deprecated uImage.FIT partition parser
In order to allow gradually migrating the boards currently using the
uImage.FIT partition (deprecated/rejected) parser to the new fitblk
driver, skip the partition parser code in case the new fitblk driver
(which serves the same purpose) is used.
As an indicator for the use of the new fitblk driver, check if the
/chosen/rootdisk property is present in the Device Tree.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Mon, 4 Dec 2023 23:25:12 +0000 (23:25 +0000)]
kernel: move uImage.FIT partition parser to mediatek target
The partition parser approach has been rejected upstream, it will be
replaced by a small block driver which is the solution suggestion by
upstream maintainers.
As the partition parser has only been used by the mediatek target, as
a first step, move it there.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Tue, 5 Dec 2023 03:44:05 +0000 (03:44 +0000)]
kernel: 6.1: backport UBI device model improvements
Backport two commits from Linux 6.3 wiring up device node parents of
ubi devices (pointing to their MTD parent) as well as ubiblock devices
(poiting to their parent UBI volume).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 12 Jan 2024 02:36:59 +0000 (02:36 +0000)]
arm-trusted-firmware-mediatek: use UBI on new NAND targets
Make use of recently added UBI support in MediaTek's ARM
TrustedFirmware-A on new MT7988 SoC.
Load fip from static UBI volume instead of fixed offset on SPIM-NAND
and SNFI.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 12 Jan 2024 02:40:20 +0000 (02:40 +0000)]
arm-trusted-firmware-mediatek: set HIDDEN=y
Hide arm-trusted-firmware-mediatek packages from interactive config.
Exposing them only causes confusion and needed variants are anyway
selected as dependencies by uboot-mediatek packages.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Chukun Pan [Sat, 26 Aug 2023 15:29:20 +0000 (23:29 +0800)]
ipq807x: add support for CMCC RM2-6
Hardware specifications:
SoC: Qualcomm IPQ8070A
RAM: 512MB of DDR3
Flash: 256MB Micron NAND
Ethernet: 2x 1G RJ45 port
WiFi1: QCN5024 2x2 2.4GHz
WiFi2: QCN5054 2x2 5GHz
Fan: 1x GPIO controlled
Button: Reset, WPS
Flash instructions:
Upload factory.bin in stock firmware's upgrade page.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Paweł Owoc [Wed, 14 Feb 2024 13:16:09 +0000 (14:16 +0100)]
qualcommax: ipq807x: MX4200 convert qca807x PHY to new implementation
Convert qca807x PHY to new implementation like for other devices.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Robert Marko [Tue, 13 Feb 2024 20:47:54 +0000 (21:47 +0100)]
qca-ssdk: drop not used Malibu PHY patch
Now that Malibu (QCA807x) PHY-s use an upstream driver we dont need support
for defining address of the first PHY in the package so drop the patch.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Robert Marko [Tue, 13 Feb 2024 20:48:52 +0000 (21:48 +0100)]
qualcommax: remove usage of malibu_first_phy_addr
Now that Malibu (QCA807x) PHY is using the upstream driver, we dont need
support to define address of the first PHY in package, so remove the
malibu_first_phy_addr DTS property.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Robert Marko [Thu, 15 Feb 2024 12:00:01 +0000 (13:00 +0100)]
generic: 6.1: use upstreamed QCA807x fixup
Now that QCA807x interface mode check was upstreamed, use the upstreamed
version and mark it as such.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Koen Vandeputte [Thu, 15 Feb 2024 10:52:29 +0000 (11:52 +0100)]
tools/expat: fix build error with ccache
Disable compilation of separate tests as it causes
a build error when combined with ccache
Fixes: 4a3f430d72 ("tools/expat: update to 2.6.0")
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
Felix Fietkau [Wed, 14 Feb 2024 15:21:36 +0000 (16:21 +0100)]
kernel: fix bidirectional hardware flow offload
Fix a bug that was introduced upstream
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Petr Štetiar [Wed, 14 Feb 2024 10:02:25 +0000 (10:02 +0000)]
ugps: update to Git HEAD (2024-02-14)
69561a074d6f ugps: add quality measurement parameters
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Felix Fietkau [Tue, 13 Feb 2024 18:24:53 +0000 (19:24 +0100)]
wifi-scripts: create the wlan object in board_data if not present
Fixes an error in wifi detection
Signed-off-by: Felix Fietkau <nbd@nbd.name>