git.openwrt.org Git - openwrt/staging/blogic.git/log

iio: adc: Add ad7124 support

The ad7124-4 and ad7124-8 are a family of 4 and 8 channel sigma-delta ADCs
with 24-bit precision and reference.

Three power modes are available which in turn affect the output data rate:
* Full power: 9.38 SPS to 19,200 SPS
* Mid power: 2.34 SPS to 4800 SPS
* Low power: 1.17 SPS to 2400 SPS

The ad7124-4 can be configured to have four differential inputs, while
ad7124-8 can have 8. Moreover, ad7124 also supports per channel
configuration. Each configuration consists of gain, reference source,
output data rate and bipolar/unipolar configuration.

Datasheets:
Link: http://www.analog.com/media/en/technical-documentation/data-sheets/AD7124-4.pdf
Link: http://www.analog.com/media/en/technical-documentation/data-sheets/ad7124-8.pdf
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

dt-bindings: iio: adc: Add common ADCs properties to a separate file

There are several ADC drivers that depend on the same device tree
bindings. Rather than continue to duplicate the properties, this patch
adds a common adc binding document that can be referenced. For beginning,
only two properties are documented.

Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: ad_sigma_delta: Allow to provide custom data register address

Some newer devices from the Sigma-Delta ADC family do have their data
register at a different address than the current default address. Add a
parameter to the ad_sigma_delta_info struct which allows to override the
default address.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

staging: iio: ad7816: Add device tree table.

Add device tree table for matching vendor ID.

Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: imu: st_lsm6dsx: add entry in MAINTAINERS file

Add entry for st_lsm6dsx imu driver in MAINTAINERS file

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: potentiometer: mcp4131: use of_device_get_match_data()

Try to get the device's data using OF API. In case of failure, fallback
to the spi_get_device_id() method.

Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

staging: iio: adc: ad7280a: use devm_* APIs

devm_* APIs are device managed and make code simpler.

Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

staging: iio: adc: ad7280a: power down the device on error in probe

Power down the device if anything goes wrong after the SPI has been
setup correctly in the probe function.

Existing code that toggles the AD7280A_CTRL_LB_SWRST bit inside
ad7280_chain_setup function is responsible for powering up the device.

Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

dt-bindings: iio: imu: st_lsm6dsx: add support to i2c pullup resistors

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: imu: st_lsm6dsx: add hw FIFO support to i2c controller

Introduce hw FIFO support to lsm6dsx i2c controller.
st_lsm6dsx sensor-hub relies on SLV0 for slave configuration since SLV0
is the only channel that can be used to write into i2c slave devices.
SLV{1,2,3} channels are used to read external data and push them into
the hw FIFO

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: imu: st_lsm6dsx: add st_lsm6dsx_push_tagged_data routine

Introduce st_lsm6dsx_push_tagged_data routine to push samples
to iio buffers. st_lsm6dsx_push_tagged_data will be reused adding
hw fifo support to st_lsm6dsx i2c embedded controller in order to
improve code readability

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: imu: st_lsm6dsx: add i2c embedded controller support

i2c controller embedded in lsm6dx series can connect up to four
slave devices using accelerometer sensor as trigger for i2c
read/write operations.
Introduce sensor hub support for lsm6dso sensor. Add register map
for lis2mdl magnetometer sensor.
In order to perform single read/write operations st_lsm6dsx driver
relies on SLV0 channel (hw FIFO is not supported yet)

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: imu: st_lsm6dsx: introduce st_lsm6dsx_sensor_set_enable routine

Add st_lsm6dsx_sensor_set_enable routine and remove
st_lsm6dsx_sensor_{enable/disable} ones in order to make the code more
readable and remove unnecessary functions

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: imu: st_lsm6dsx: introduce ST_LSM6DSX_ID_EXT sensor ids

Add ST_LSM6DSX_ID_EXT{0,1,2} sensor ids as reference for slave devices
connected to st_lsm6dsx i2c controller. Moreover introduce odr dependency
between accel and ext devices since i2c embedded controller relies on the
accelerometer sensor as bus read/write trigger so we need to enable accel
device at odr = max(accel_odr, ext_odr) in order to properly communicate
with i2c slave devices

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: imu: st_lsm6dsx: remove static from st_lsm6dsx_set_watermark

Remove static qualifier from st_lsm6dsx_set_watermark routine in
order to be reused supporting st_lsm6dsx i2c controller

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: imu: st_lsm6dsx: reload trimming parameter at bootstrap

Perform a complete device reset at bootstrap reloading trimming parameter
after sw reset is completed. Device sw reset/boot is explained here:
https://www.st.com/resource/en/application_note/dm00517282.pdf,
section 5.7

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: imu: st_lsm6dsx: introduce locked read/write utility routines

Add st_lsm6dsx_update_bits_locked, st_lsm6dsx_read_locked and
st_lsm6dsx_write_locked utility routines in order to guarantee
the bus access is atomic respect to reg page configuration.
This is a preliminary patch to add i2c sensor hub support since
i2c master registers are accessed through a reg page multiplexer

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: sc27xx: Add ADC data conversion timeout

Sometimes the ADC controller met some problems, and it will not complete
the data conversion, that will can not wake up the read process any more
to block users. So we should add one maximum conversion time to avoid
this issue.

Signed-off-by: Freeman Liu <freeman.liu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

staging: iio: ad7780: remove unnecessary stashed voltage value

This patch removes the unnecessary field int_vref_mv in ad7780_state
referring to the device's voltage.

Signed-off-by: Renato Lui Geh <renatogeh@gmail.com>
Acked-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

staging: iio: ad7780: update voltage on read

The ad7780 driver previously did not read the correct device output, as
it read an outdated value set at initialization. It now updates its
voltage on read.

Signed-off-by: Renato Lui Geh <renatogeh@gmail.com>
Acked-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: magnetometer: Add driver support for PNI RM3100

PNI RM3100 is a high resolution, large signal immunity magnetometer,
composed of 3 single sensors and a processing chip with a MagI2C
interface.

Following functions are available:
- Single-shot measurement from
/sys/bus/iio/devices/iio:deviceX/in_magn_{axis}_raw
- Triggerd buffer measurement.
- DRDY pin for data ready trigger.
- Both i2c and spi interface are supported.
- Both interrupt and polling measurement is supported, depends on if
the 'interrupts' in DT is declared.

Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: magnetometer: Add DT support for PNI RM3100

Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

dt-bindings: Add PNI to the vendor prefixes

Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: st-accel: add support for lis3de

This commit add support for STMicroelectronics lis3de accelerometer.
Datasheet for this device can be found here:

https://www.st.com/resource/en/datasheet/lis3de.pdf

Signed-off-by: Heiko Stuebner <heiko.stuebner@bq.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: light: Add device tree binding for vishay vcnl4035

Adding device tree binding for vcnl4035 and vendor
prefix for Vishay Intertechnology

Signed-off-by: Parthiban Nallathambi <pn@denx.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: light: Add support for vishay vcnl4035

Add support for VCNL4035, which is capable of Ambient light
sensing (ALS) and proximity function. This patch adds support
only for ALS function

Signed-off-by: Parthiban Nallathambi <pn@denx.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: rcar-gyroadc: convert to SPDX identifiers

This patch updates license to use SPDX-License-Identifier
instead of verbose license text.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: max11100: convert to SPDX identifiers

This patch updates license to use SPDX-License-Identifier
instead of verbose license text.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: max9611: convert to SPDX identifiers

This patch updates license to use SPDX-License-Identifier
instead of verbose license text.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

staging: iio: ad7780: generates pattern_mask from PAT bits

Previously, all pattern_masks and patterns in the chip_info table were
hardcoded. Now they are generated using the PAT macros, as described in
the datasheets.

Signed-off-by: Giuliano Belinassi <giuliano.belinassi@usp.br>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

staging: iio: ad7780: check if ad778x before gain update

Only the ad778x have the 'gain' status bit. Check it before updating
through a new variable is_ad778x in chip_info.

Signed-off-by: Giuliano Belinassi <giuliano.belinassi@usp.br>
Acked-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

staging: iio: ad7816: Set RD/WR pin and CONVST pin as outputs.

The RD/WR pin and CONVST pin are logical inputs to the AD78xx
chip as per the datasheet. Hence convert them to outputs.

Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

staging: iio: ad7816: Do not use busy_pin in case of AD7818

AD7818 does not support busy_pin functionality as per datasheet.
Hence drop busy_pin when AD7818 is used.

Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: meson-saradc: add support for the chip's temperature sensor

Channel 6 of the SAR ADC can be switched between two inputs:
SAR_ADC_CH6 input (an actual pad on the SoC) and the signal from the
temperature sensor inside the SoC.

To get usable results from the temperature sensor we need to read the
corresponding calibration data from the eFuse and pass it to the SAR ADC
registers. If the temperature sensor is not calibrated (the eFuse data
contains a bit for this) then the driver will only register the
iio_chan_spec's for voltage measurements.

This only enables the temperature sensor for the Meson8 SoC. Meson8b and
Meson8m2 SoCs can be supported in the future as well but we first need
a way to pass the fifth TSC (temperature sensor coefficient) bit to the
HHI register area (apart from that the infrastructure as already
implemented for Meson8 can be used). On the 64-bit SoCs (GXBB, GXL and
GXM) the temperature sensor inside SAR ADC is firmware-controlled (by
BL30, we can simply use the SCPI hwmon driver to get the chip
temperature).

To keep the devicetree interface backwards compatible we simply skip the
temperature sensor initialization if no eFuse nvmem cell is passed via
devicetree.

The public documentation for the SAR ADC IP block does not explain how
to use the registers to read the temperature. The logic from this patch
is based on reading and understanding Amlogic's GPL kernel sources.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

dt-bindings: iio: adc: meson-saradc: add temperature sensor support

The 32-bit Meson8 SoC can use the SAR ADC to read the chip temperature.
This requires setting the correct TSC (temperature sensor coefficient),
which is programmed into the eFuse during the manufacturing process.
Meson8b and Meson8m2 are not supported yet because they have a 5-bit TSC
and only the first four bits are stored inside the SAR ADC registers.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

staging:iio:ad2s90: Check channel type at read_raw

This patch adds a channel type check at the beginning of the
ad2s90_read_raw function. Since ad2s90 has only one channel, it just
checks if the given channel is the expected one and if not, return
-EINVAL.

Signed-off-by: Matheus Tavares <matheus.bernardino@usp.br>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

staging:iio:ad2s90: Add IIO_CHAN_INFO_SCALE to channel spec and read_raw

This patch adds the IIO_CHAN_INFO_SCALE mask to ad2s90_chan and
implements the relative read behavior at ad2s90_read_raw.

Signed-off-by: Victor Colombo <victorcolombo@gmail.com>
Signed-off-by: Matheus Tavares <matheus.bernardino@usp.br>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

staging:iio:ad2s90: Move device registration to the end of probe

Previously, devm_iio_device_register was being called before the
spi_setup call and the spi_device's max_speed_hz and mode assignments.
This could lead to a race condition since the driver was still being
set up after it was already made ready to use. To fix it, this patch
moves the device registration to the end of ad2s90_probe.

Signed-off-by: Matheus Tavares <matheus.bernardino@usp.br>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

staging:iio:ad2s90: Remove always overwritten assignment

This patch removes an initial assignment to the variable ret at probe,
that was always overwritten.

Signed-off-by: Matheus Tavares <matheus.bernardino@usp.br>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

staging:iio:ad2s90: Make probe handle spi_setup failure

Previously, ad2s90_probe ignored the return code from spi_setup, not
handling its possible failure. This patch makes ad2s90_probe check if
the code is an error code and, if so, do the following:

- Call dev_err with an appropriate error message.
- Return the spi_setup's error code.

Note: The 'return ret' statement could be out of the 'if' block, but
this whole block will be moved up in the function in the patch:
'staging:iio:ad2s90: Move device registration to the end of probe'.

Signed-off-by: Matheus Tavares <matheus.bernardino@usp.br>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

staging:iio:ad2s90: Make read_raw return spi_read's error code

Previously, when spi_read returned an error code inside ad2s90_read_raw,
the code was ignored and IIO_VAL_INT was returned. This patch makes the
function return the error code returned by spi_read when it fails.

Signed-off-by: Matheus Tavares <matheus.bernardino@usp.br>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

staging: iio: ad7780: fix offset read value

Variable val subtracted an uninitialized value on IIO_CHAN_INFO_OFFSET.
This was fixed by assigning the correct value instead.

Signed-off-by: Renato Lui Geh <renatogeh@gmail.com>
Acked-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

staging: iio: ad2s1210: Add device tree table.

Add device tree table for matching vendor ID.

Note that as the driver is still heavily in flux and there are some
non obvious aspects to a comprehensive binding, that binding will
be submitted at a later date (before leaving staging!)

Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

staging: iio: ad2s1210: Drop the gpioin flag.

Drop gpioin flag which decides how the GPIOs
are controlled as the GPIOs must be outputs
for the host as per the datasheet.

Removes need for platform data so that is dropped as well.

Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

staging: iio: ad2s1210: Switch to the gpio descriptor interface

Use the gpiod interface instead of the deprecated old non-descriptor
interface.

Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: potentiometer: tpl0102: add IIO_AVAIL_RANGE support

Report the step range of the respective potentiometers that are
possible to userspace.

Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

dt-bindings: iio: dac: Add ti,dac7311 device tree bindings in documentation

Description how to invoke ti-dac7311 driver from device tree file.

Signed-off-by: Charles-Antoine Couret <charles-antoine.couret@essensium.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio:dac:ti-dac7311 Add driver for Texas Instrument DAC7311

It is a driver for Texas Instruments 8/10/12-bit 1-channel
compatible with DAC6311 and DAC5311 chips.

Datasheet of this chip:
http://www.ti.com/lit/ds/symlink/dac7311.pdf

Signed-off-by: Charles-Antoine Couret <charles-antoine.couret@essensium.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

dt-bindings: iio: magn: add LSM9DS1 bindings

Add DT binding documentation for the LSM9DS1 magnetometer.

Signed-off-by: Martin Kelly <martin@martingkelly.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

staging: iio: adc: ad7280a: don't cast type inside switch expression

The type promotion will kick in, so the comparison will work.

Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio:magnetometer: st_magn: add BDU settings

LIS3MDL and LSM9DS1 are missing BDU settings in their register maps, so add
them. I don't have a LIS3MDL sensor to test, but this works correctly on
the LSM9DS1, which has the same register map.

Signed-off-by: Martin Kelly <martin@martingkelly.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio:magnetometer: st_magn: add LSM9DS1 support

Update the sensor settings to support the LSM9DS1 sensor. Although the
LSM9DS1 accelerometer and gyroscope are coupled together to use the same
FIFO, the magnetometer is separate and can be cleanly supported without
refactoring the existing driver.

Signed-off-by: Martin Kelly <martin@martingkelly.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: magnetometer: add clarifying comment

Add a comment clarifying better when to use <device_name> vs
<device_name>-magn in compatibility strings.

Signed-off-by: Martin Kelly <martin@martingkelly.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: potentiometer: tpl0102: switch to using pointer to chip config

More concise to have a pointer to tpl0102_cfg struct in the iio_priv
data than an integer to an index of an array.

Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Reviewed-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

dt-bindings: iio: adc: Add AD7949 device tree bindings in documentation

Description how to invoke ad7949 driver from device tree file.

Signed-off-by: Charles-Antoine Couret <charles-antoine.couret@essensium.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio:adc:ad7949: Add AD7949 ADC driver family

Compatible with AD7682 and AD7689 chips.
It is a Analog Devices ADC driver 14/16 bits 4/8 channels
with SPI protocol

Datasheet of the device:
http://www.analog.com/media/en/technical-documentation/data-sheets/AD7949.pdf

Signed-off-by: Charles-Antoine Couret <charles-antoine.couret@essensium.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

staging: iio: ad5933: Remove unnecessary blank line

This patch fixes the checkpatch.pl warning:

WARNING: Blank lines aren't necessary before a close brace '}'

Signed-off-by: Victor Colombo <victorcolombo@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

staging: iio: ad5933: Remove unnecessary space on casting

This patch fixes the checkpatch.pl warning:

WARNING: No space is necessary after a cast

Signed-off-by: Victor Colombo <victorcolombo@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc128s052: use SPDX-License-Identifier

This updates the ti-adc128s052.c file to use SPDX-License-Identifier
instead of more verbose license text.

Signed-off-by: Dan O'Donovan <dan@emutex.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc128s052: add ACPI _HID AANT1280

ACPI _HID AANT1280 matches an ADC124S101 present on E3940 SKUs of the UP
Squared board.

Add it to the driver.

Signed-off-by: Nicola Lunghi <nicola.lunghi@emutex.com>
[javier@emutex.com: fix up commit message and one checkpatch warning]
Signed-off-by: Javier Arteaga <javier@emutex.com>
Signed-off-by: Dan O'Donovan <dan@emutex.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc128s052: Add pin-compatible IDs

The datasheets for ADC122S021 and ADC124S021 list two more
pin-compatible alternatives for each device.

Add their IDs as compatible strings.

Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Javier Arteaga <javier@emutex.com>
Signed-off-by: Dan O'Donovan <dan@emutex.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

staging: iio: ad7816: Switch to the gpio descriptor interface

Use the gpiod interface for rdwr_pin, convert_pin and busy_pin
instead of the deprecated old non-descriptor interface.

Note that Phil Reid identified that some of this code would never
have worked. A follow up patch can fix that as this is just
a direct change of interface.

Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: ina2xx: add in early -EINVAL returns in case statements

Static analysis with CoverityScan is throwing warnings that specific
case statements are missing breaks.  Rather than adding breaks, add
return -EINVAL to the specific case statements to clarify the
error return paths. Fix also saves 50 bytes.

Before:
   text    data     bss     dec     hex filename
  21418    4936     128   26482    6772 drivers/iio/adc/ina2xx-adc.o

After:
  dec     hex filename
  21370    4936     128   26434    6742 drivers/iio/adc/ina2xx-adc.o

(gcc 8.2, x86-64)

Detected by CoverityScan, CID#1462408 ("Missing break in switch")

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Staging:iio:adc:ad7606: Match parenthesis alignment

Change close parenthesis alignment to match respective open parenthesis at
iio/drivers/staging/iio/adc/ad7606.c line 379.
This makes the file more compliant with the preferred coding style for the
linux kernel.

Signed-of-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: st_sensors: miscellaneous cleanup

Miscellaneous cleanup to fix minor consistency, grammar, and spelling
issues.

Signed-off-by: Martin Kelly <martin@martingkelly.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

staging: iio: adc: ad7280a: use crc8.h API to build crc table

The custom build function ad7280_crc8_build_table is not needed. The
crc8_populate_msb function from linux/crc8.h will build the same crc
table.

Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

staging: iio: adc: ad7280a: handle error from __ad7280_read32()

Inside __ad7280_read32(), the spi_sync_transfer() can fail with negative
error code. This change will ensure that this error is being passed up
in the call stack, so it can be handled.

Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

tools iio: Override CFLAGS assignments

So user could specify outside CFLAGS values.

Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: accel: kxcjk1013: Add KIOX0009 ACPI Hardware-ID

Add KIOX0009 ACPI HID, this is used e.g. on the Acer One 10.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

staging: iio: adt7316: fix parenthesis alignment

This patch fixes most "Alignment should match open parenthesis" check
warnings found by checkpatch.pl in the addac/adt7316 driver.

Signed-off-by: Renato Lui Geh <renatogeh@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: dpot-dac: mark expected switch fall-through with text GCC expects.

In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

Notice that in this particular case, I replaced "...and fall through."
with the specific string "fall through", which is what GCC is
expecting to find thus supressing this false positive.

As Peter has observed this breaks the nice English flow, which is
less than ideal, but short of teaching GCC to read English, there
isn't a lot that we can do about it.

Addresses-Coverity-ID: 1462408 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

staging: iio: ad2s1210: fix 'assignment operator' style checks

This patch fixes all "Assignment operator '=' should be on the previous
line" checks found in ad2s1210.c with checkpatch.pl.

Signed-off-by: Matheus Tavares <matheus.bernardino@usp.br>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

staging: iio: cdc: ad7150: fix misaligned lines

These lines were misaligned, but the checkpatch.pl didn't indicate them
as such.

Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

staging: iio: cdc: ad7150: use value copy to shorten the line length

By using the copy of channel attribute, we can now make the lines short
enough to eliminate the checkpatch.pl problem:

CHECK: Alignment should match open parenthesis

Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: ssp_sensors: don't manually free devm managed resources

The charme of devm_* functions is that you don't need to care about them
in the error path. In this case it is valid to just return NULL which makes
the device fail to probe and then the two gpios and the allocated memory
are freed automatically by the driver core.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

staging: iio: ad5933: rename ext_clk_Hz -> ext_clk_hz

The checkpatch script doesn't like camel-case names.
Renamed the variable.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: Fix Renesas GyroADC MAINTAINERS entry

Fix the F: entry in MAINTAINERS file, point it to the correct file.
While at it, add DT binding doc F: entry too.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Perches <joe@perches.com>
Cc: linux-renesas-soc@vger.kernel.org
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

staging: rtl8712: add SPDX identifiers

This satisfies a checkpatch warning and is the preferred
method for notating the license.

The SPDX identifier is a legally binding shorthand, which
can be used instead of the full boiler plate text.

Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: fbtft: Prefer using the BIT macro

Replacing all occurrences of (1<<x) with BIT(x) to fix checkpatch issue.
CHECK:Prefer using the BIT macro

Signed-off-by: Mamta Shukla <mamtashukla555@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8188eu: fix spelling mistake in comment

Fix a spelling mistake reported by checkpatch.
Caculate -> Calculate

Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8188eu: remove braces from single if statement

Remove braces from single line if statement.
Reported by checkpatch.

Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8188eu: remove unnecessary parentheses in odm_rtl8188e.c

Remove unnecessary parentheses in odm_rtl8188e.c.
Reported by checkpatch.

Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8188eu: add spaces around '+' in fw.c

Add spaces around '+' in fw.c to follow kernel coding style.
Reported by checkpatch.

Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8188eu: simplify block comment in pwrseq.c

Simplify block comment to a single line to clear a checkpatch warning.
WARNING: Block comments use * on subsequent lines

Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8188eu: correct block comment in bb_cfg.c

Correct block comment to clear a checkpatch warning.
WARNING: Block comments should align the * on each line

Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8188eu: rename odm_SignalScaleMapping()

Rename odm_SignalScaleMapping to avoid CamelCase.
odm_SignalScaleMapping -> odm_signal_scale_mapping

Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8188eu: rename variable in odm_SignalScaleMapping()

Rename variable in odm_SignalScaleMapping() to avoid CamelCase.
RetSig -> retsig

Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8188eu: rename parameter of odm_SignalScaleMapping()

Rename parameter of odm_SignalScaleMapping() to avoid CamelCase.
CurrSig -> currsig

Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8188eu: rename odm_EVMdbToPercentage()

Rename odm_EVMdbToPercentage() to avoid CamelCase.
odm_EVMdbToPercentage -> odm_evm_db_to_percentage

Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8188eu: rename parameter of odm_EVMdbToPercentage()

Rename parameter of odm_EVMdbToPercentage() to avoid CamelCase.
Value -> value

Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8188eu: rename odm_QueryRxPwrPercentage()

Rename odm_QueryRxPwrPercentage() to avoid CamelCase.
odm_QueryRxPwrPercentage -> odm_query_rxpwrpercentage

Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8188eu: rename parameter of odm_QueryRxPwrPercentage()

Rename parameter of odm_QueryRxPwrPercentage() to avoid CamelCase.
AntPower -> antpower

Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8188eu: replace tabs with spaces in odm_hwconfig.c

Replace tabs with spaces in odm_hwconfig.c where appropriate.

Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8188eu: add spaces around '*' in odm_hwconfig.c

Add spaces around '*' in odm_hwconfig.c to follow kernel coding style.
Reported by checkpatch.

Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8188eu: add spaces around '+' in odm_hwconfig.c

Add spaces around '+' in odm_hwconfig.c to follow kernel coding style.
Reported by checkpatch.

Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8188eu: remove wrapper odm_SignalScaleMapping()

The function odm_SignalScaleMapping() is just a wrapper for
odm_SignalScaleMapping_92CSeries().

Rename odm_SignalScaleMapping_92CSeries() to odm_SignalScaleMapping()
and remove the wrapper.

Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8188eu: rename odm_HWConfig

Rename source and header file to avoid CamelCase.
odm_HWConfig.c -> odm_hwconfig.c
odm_HWConfig.h -> odm_hwconfig.h

Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8188eu: cleanup inconsistent indenting

Cleanup all inconsistent indenting reported by smatch.

Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: ks7010: Remove unnecessary null check

Remove the unnecessary socket buffer null check in hostif_data_request.
There is already an appropriate null check in the calling function:

(ks_wlan_net.c) ks_wlan_start_xmit

Signed-off-by: Aymen Qader <qader.aymen@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>