regulator: s2mps11: Adjust supported buck voltages to real values

The driver was registering buck regulators with unsupported range of
voltages for S2MPS11 devices.  Basically it assumed that all 256 values
are possible for a single 8-bit I2C register controlling buck's voltage.
This is not true, as datasheet describes subset of these which can be
used.

For example for buck[12346] the minimum voltage is 650 mV which
corresponds to register value of 0x8.  The driver was however
registering regulator starting at 600 mV, so for a step of 6.25 mV this
gave the same result.  However this allowed to try to configure
regulators to unsupported values.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: s2mps11: Fix buck7 and buck8 wrong voltages

On S2MPS11 device, the buck7 and buck8 regulator voltages start at 750
mV, not 600 mV.  Using wrong minimal value caused shifting of these
regulator values by 150 mV (e.g. buck7 usually configured to v1.35 V was
reported as 1.2 V).

On most of the boards these regulators are left in default state so this
was only affecting reported voltage.  However if any driver wanted to
change them, then effectively it would set voltage 150 mV higher than
intended.

Cc: <stable@vger.kernel.org>
Fixes: cb74685ecb39 ("regulator: s2mps11: Add samsung s2mps11 regulator driver")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: s2mps11: Fix ERR_PTR dereference on GPIO lookup failure

If devm_gpiod_get_from_of_node() call returns ERR_PTR, it is assigned
into an array of GPIO descriptors and used later because such error is
not treated as critical thus it is not propagated back to the probe
function.

All code later expects that such GPIO descriptor is either a NULL or
proper value.  This later might lead to dereference of ERR_PTR.

Only devices with S2MPS14 flavor are affected (other do not control
regulators with GPIOs).

Fixes: 1c984942f0a4 ("regulator: s2mps11: Pass descriptor instead of GPIO number")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: tps6507x: Fix boot regression due to testing wrong init_data pointer

A NULL init_data once incremented will lead to oops, fix it.

Fixes: f979c08f7624 ("regulator: tps6507x: Convert to regulator core's simplified DT parsing code")
Reported-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: core: simplify return value on suported_voltage

All the current clients of this API  assume that 0 corresponds
to a failure and non-zero to a pass therefore ignoring the need to
handle a negative error code.

This commit modifies the API to follow that standard since returning a
negative (EINVAL) doesn't seem to provide enough value to justify
the need to handle it.

Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: da9xxx: Switch to SPDX identifier

Convert Dialog Semiconductor DA9xxx regulator drivers to SPDX identifier.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: stm32-pwr: Remove unneeded .min_uV and .list_volage

For fixed regulator, setting .n_voltages = 1 and .fixed_uV is enough,
no need to set .min_uV and .list_volage.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: stm32-pwr: Remove unneeded *desc from struct stm32_pwr_reg

Just use rdev->desc instead.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: ab3100: Set fixed_uV instead of min_uV for fixed regulators

Slightly better readability by setting fixed_uV instead of min_uV.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: ab3100: Constify regulator_ops and ab3100_regulator_desc

These regulator_ops variables and ab3100_regulator_desc array never need
to be modified, make them const so compiler can put them to .rodata.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: pv880x0: Switch to SPDX identifier

Convert Powerventure Semiconductor PV88060/PV88080/PV88090 regulator
drivers to SPDX identifier.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: hi6xxx: Switch to SPDX identifier

Convert HiSilicon hi6xxx PMIC drivers to SPDX identifier.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: vexpress: Switch to SPDX identifier

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: vexpress: Get rid of struct vexpress_regulator

The *regdev and *regmap can be replaced by local variables in probe().
Only desc of struct vexpress_regulator is really need, so just use
struct regulator_desc directly and remove struct vexpress_regulator.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: sky81452: Switch to SPDX identifier

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: sky81452: Constify sky81452_reg_ops

sky81452_reg_ops is never changed, make it const.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: sy8106a: Get rid of struct sy8106a

All the fields in struct sy8106a are only used in sy8106a_i2c_probe(), so
use local variables instead.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: core: do not report EPROBE_DEFER as error but as debug

Temporary failures to get a regulator (EPROBE_DEFER) should be logged
as debug information instead of errors.

Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: mt63xx: Switch to SPDX identifier

Convert MediaTek mt63xx PMIC drivers to SPDX identifier.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: fan53555: Switch to SPDX identifier

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: fan53555: Clean up unneeded fields from struct fan53555_device_info

The *regmap and *rdev can be replaced by local variables.
The slew_rate is no longer used since commit dd7e71fbeefe
("regulator: fan53555: use set_ramp_delay to set the ramp up slew rate").

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: ltc3589: Switch to SPDX identifier

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: ltc3589: Get rid of struct ltc3589_regulator

After converting to use simplified DT parsing, the struct ltc3589_regulator
only has a desc member. So let's remove struct ltc3589_regulator and use
struct regulator_desc instead.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: ltc3589: Convert to use simplified DT parsing

Use regulator core's simplified DT parsing code to simplify the driver
implementation.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: wm8400: Switch to SPDX identifier

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: wm8350: Switch to SPDX identifier

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: wm831x: Switch to SPDX identifier

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: arizona: Switch to SPDX identifier

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: wm8994: Switch to SPDX identifier

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: stm32-pwr: Fix return value check in stm32_pwr_regulator_probe()

In case of error, the function of_iomap() returns NULL pointer not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.

Fixes: 6cdae8173f67 ("regulator: Add support for stm32 power regulators")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: ready_mask_table[] can be static

Fixes: 6cdae8173f67 ("regulator: Add support for stm32 power regulators")
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: tps80031: Switch to SPDX identifier

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: tps80031: Constify regulator_ops and tps80031_dcdc_voltages array

These regulator_ops variables and tps80031_dcdc_voltages array never need
to be modified, make them const so compiler can put them to .rodata.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: tps80031: Remove unused *rdev from struct tps80031_regulator

The ri-rdev is assigend but not used, so remove it.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: Add support for stm32 power regulators

Add support for 1V1 1V8 USB3V3 power regulators.

Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

dt-bindings: regulator: Add stm32mp1 pwr regulators

Document devicetree bindings for stm32mp1 pwr regulators.

Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: max8998: Factor out struct voltage_map_desc

The struct voltage_map_desc is used for storing min/max/step fileds, and
then setup the min_uV, uV_step and n_voltages fields for regulator_desc.
Introduce MAX8998_LINEAR_REG/MAX8998_OTHERS_REG macro to setup these filds
directly in regulator_desc to simplify the code.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: max8998: Constify regulator_ops

These regulator_ops variables never need to be modified, make them const so
compiler can put them to .rodata.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: tps6524x: Remove *rdev[N_REGULATORS] from struct tps6524x

Current code is using devm_regulator_register() so we don't need to store
*rdev for clean up, use a local variable instead.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: tps6524x: Constify regulator_ops

The regulator_ops is never changed, make it const.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: tps65218: Convert to use regulator_get_current_limit_regmap

Use regulator_get_current_limit_regmap helper to save some code.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: ab8500: Remove *regulator from struct ab8500_regulator_info

Current code is using devm_regulator_register() so we don't need to save
*regulator for clean up, use a local variable instead.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: ab8500: Constify regulator_ops

These regulator_ops variables never need to be modified, make them const so
compiler can put them to .rodata.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: ab8500-ext: Constify ab8500_ext_regulator_ops

ab8500_ext_regulator_ops never need to be modified, make it const so
compiler can put it to .rodata.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: ab8500-ext: Convert to use simplified DT parsing

Use regulator core's simplified DT parsing code to simplify the driver
implementation.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: ab8500-ext: Remove *rdev from struct ab8500_ext_regulator_info

Current code is using devm_regulator_register() so we don't need to save
*rdev for clean up, use a local variable instead.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: dbx500-prcmu: Remove unused fields from struct dbx500_regulator_info

The *dev is assigned but not used, remove it.
Current driver is using devm_regulator_register(), so no neeed to save
*rdev for clean up. Use a local variable instead.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: db8500-prcmu: Convert to use simplified DT parsing

Use regulator core's simplified DT parsing code to simplify the driver
implementation.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: db8500-prcmu: Constify regulator_ops

These regulator_ops variables never need to be modified, make them const so
compiler can put them to .rodata.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: mcp16502: Remove setup_regulators function

It seems a little bit odd current code pass struct regulator_config rather
than a pointer to setup_regulators. The setup_regulators is so simple and
only has one caller, so remove it.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: mcp16502: Remove unneeded fields from struct mcp16502

At the context with rdev, we can use rdev->regmap instead of mcp->rmap.
The *rdev[NUM_REGULATORS] is not required because current code uses
devm_regulator_register() so we don't need to store *rdev for clean up
paths.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: vexpress: Constify regulator_ops

vexpress_regulator_ops_ro and vexpress_regulator_ops are never changed,
make them const.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: hi6421: Convert to use simplified DT parsing

Use regulator core's simplified DT parsing code to simply the driver
implementation.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: anatop: Remove unneeded fields from struct anatop_regulator

These fields are only used in anatop_regulator_probe() so use local
variables instead. The *initdata is not used so can be removed.
The *anatop is renamed to *regmap for better readability.
Use u32 instead of int for the variables used as third argument of
of_property_read_u32().

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: s2mpa01: Remove unused define for S2MPA01_REGULATOR_CNT

The S2MPA01_REGULATOR_CNT is no longer used after converted to use
simplified DT parsing.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: hi655x: Remove ctrl_mask field from struct hi655x_regulator

The rdev->desc->enable_mask setting is always the same as
BIT(regulator->ctrl_mask), so just use rdev->desc->enable_mask instead.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: hi655x: Constify regulators array

The regulators array should never need to be modified, make it const so
compiler can put it to .rodata.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: s2mpa01: Convert to use simplified DT parsing

Use regulator core's simplified DT parsing code to simply the driver
implementation.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: bd718x7: Use rdev_get_id() to get regulator id

Use rdev_get_id() instead of directly access rdev->desc->id.
While at it also remove unneeded init for ramp_value variable.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: ab8500: add range to usleep_range

Providing a range for usleep_range() allows the hrtimer subsystem to
coalesce timers - as this delay has no upper limit anyway (interrupts
or context switch is possible) it should not hurt to extend this
from 2 to 2-4 milliseconds.

Signed-off-by: Nicholas Mc Guire <hofrat@opentech.at>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: twl: Constify regulator_ops

These regulator_ops variables never need to be modified, make them const so
compiler can put them to .rodata.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: lm363x: Constify regulator_ops

The lm363x_boost_voltage_table_ops and lm363x_regulator_voltage_table_ops
never need to be modified, make them const so compiler can put them to
.rodata.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: lm363x: Use proper data type for regmap_read arguments

regmap_read() takes unsigned int reg and unsigned int *val arguments,
use proper data type for these arguments.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: bcm590xx: Convert to use simplified DT parsing

Use regulator core's simplified DT parsing code to simply the driver
implementation.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: as3722: Slightly improve readability

Add a local variable *desc to avoid too many change lines due to over 80
characters.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: as3722: Convert to use regulator_set/get_current_limit_regmap

Use regulator_set/get_current_limit_regmap helpers to save some code.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: tps6507x: Convert to regulator core's simplified DT parsing code

Use regulator core's simplified DT parsing code to simply the driver
implementation.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: tps6507x: Remove unused *rdev[] from struct tps6507x_pmic

This driver is using devm_regulator_register so no need to save *rdev for
clean up.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: tps6507x: Constify tps6507x_pmic_ops

The tps6507x_pmic_ops never need to be modified, make it const so compiler
can put it to .rodata.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: vctrl: Remove unneeded continue statement

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: rc5t583: Get rid of struct rc5t583_regulator

The struct rc5t583_regulator only has 2 members, the *rdev is no longer
used because this driver is using devm_regulator_register now. After remove
*rdev, only *reg_info left. We can use struct rc5t583_regulator_info
directly, so remove struct rc5t583_regulator.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: act8865: Constify regulator_ops

The act8865_ops and act8865_ldo_ops never need to be modified,
make them const so compiler can put them to .rodata.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: act8865: Convert to regulator core's simplified DT parsing code

Use regulator core's simplified DT parsing code to simply the driver
implementation. With this conversion, also move the NULL test against pdata
in act8865_get_regulator_data() to the caller. This makes it clear the
code path to explicitly set init_data is for non-DT case only.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: sc2731: Constify regulators

The regulators array should never need to be modified, make it const so
compiler can put it to .rodata.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: da9063: convert header to SPDX

Covnert the header of the source file to SPDX.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: tps65217: Constify regulator_ops

These regulator_ops variables never need to be modified, make them const so
compiler can put them to .rodata.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: tps65218: Constify regulator_ops

These regulator_ops variables never need to be modified, make them const so
compiler can put them to .rodata.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: uniphier: Fix build dependency

This driver does not use any syscon APIs, so remove MFD_SYSCON dependency.
Select REGMAP_MMIO since this driver uses devm_regmap_init_mmio().

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: tps65086: Fix tps65086_ldoa1_ranges for selector 0xB

selector 0xB (1011) should be 2.6V rather than 2.7V, fit ix.

Table 5-4. LDOA1 Output Voltage Options
VID Bits VOUT VID Bits VOUT VID Bits VOUT VID Bits VOUT
0000     1.35 0100     1.8  1000     2.3  1100     2.85
0001     1.5  0101     1.9  1001     2.4  1101     3.0
0010     1.6  0110     2.0  1010     2.5  1110     3.3
0011     1.7  0111     2.1  1011     2.6  1111     Not Used

Fixes: d2a2e729a666 ("regulator: tps65086: Add regulator driver for the TPS65086 PMIC")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: add regulator_get_linear_step() stub helper

The regulator header has empty inline functions for most interfaces,
but not regulator_get_linear_step(), which has just grown a user
that does not depend on regulators otherwise:

drivers/clk/tegra/clk-tegra124-dfll-fcpu.c: In function 'get_alignment_from_regulator':
drivers/clk/tegra/clk-tegra124-dfll-fcpu.c:555:19: error: implicit declaration of function 'regulator_get_linear_step'; did you mean 'regulator_get_drvdata'? [-Werror=implicit-function-declaration]
  align->step_uv = regulator_get_linear_step(reg);
                   ^~~~~~~~~~~~~~~~~~~~~~~~~
                   regulator_get_drvdata
cc1: all warnings being treated as errors
scripts/Makefile.build:278: recipe for target 'drivers/clk/tegra/clk-tegra124-dfll-fcpu.o' failed

Add the missing stub along the others.

Fixes: b3cf8d069505 ("clk: tegra: dfll: CVB calculation alignment with the regulator")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: tps65217: Simplify linear range for selector 25-52

The original code separates the selector 25-52 into 2 ranges on purpose
because DCDC1/DCDC3 only support up to 1.8V/1.5V in the old code.
Both DCDC1 and DCDC3 support up to 3.3V since commit b4c2e158a1e1
("regulator: tps65217: Allow DCDC1 and DCDC3 up to 3.3V"), so merge
25-30 and 31-52 ranges to one range.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: tps65132: Constify tps65132_regulator_ops and tps_regs_desc

The tps65132_regulator_ops and tps_regs_desc never need to be modified,
make them const so compiler can put them to .rodata.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: tps65132: Remove unneeded fields from struct tps65132_regulator

These fields are not really need, remove them.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: axp20x: Mark expected switch fall-throughs

In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.

This patch fixes the following warnings:

drivers/regulator/axp20x-regulator.c: In function ‘axp20x_set_dcdc_freq’:
drivers/regulator/axp20x-regulator.c:1023:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
   reg = AXP803_DCDC_FREQ_CTRL;
drivers/regulator/axp20x-regulator.c:1025:2: note: here
  case AXP806_ID:
  ^~~~
drivers/regulator/axp20x-regulator.c: In function ‘axp20x_set_dcdc_workmode’:
drivers/regulator/axp20x-regulator.c:1115:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
   reg = AXP806_DCDC_MODE_CTRL2;
drivers/regulator/axp20x-regulator.c:1121:2: note: here
  case AXP221_ID:
  ^~~~

Notice that in this particular case, I moved the whole comment
"Fall through to the check below.", which contains the "Fall through"
comment, at the bottom of the case, which is what GCC is expecting
to find.

Warning level 3 was used: -Wimplicit-fallthrough=3

This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: gpio: Reword the binding document

Reword the binding document to make it clear how the propeties work
and which properties affect which other properties.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Harald Geyer <harald@ccbib.org>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: linux-renesas-soc@vger.kernel.org
To: devicetree@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: rn5t618: Constify regulator_desc

The regulator_desc never need to be modified, so define them as const as a
hint to the compiler that they can go into .rodata.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: max8925: Convert to regulator core's simplified DT parsing code

Use regulator core's simplified DT parsing code to simply the driver
implementation.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: of: Make regulator_of_get_init_node static

Fix sparse warning:

drivers/regulator/of_regulator.c:374:20:
 warning: symbol 'regulator_of_get_init_node' was not declared. Should it be static?

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Merge tag 'v5.1-rc1' into regulator-5.2

Linux 5.1-rc1

regulator: axp20x: Use rdev_get_id at appropriate places

Use rdev_get_id() to simplify the code a bit.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: axp20x: Remove unneeded NULL test against rdev

rdev won't be NULL in .enable callback.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: 88pm8607: Convert to regulator core's simplified DT parsing code

Use regulator core's simplified DT parsing code to simply the driver
implementation.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: core: Fix application of "drop lockdep annotation in drms_uA_update()"

[The original commit was sent against -next but needed to be sent as a
bugfix, however -next had some additional changes which needed to be
reverted.  Now everything is all in one branch applying the rest of the
changes to fix up the merge issue -- broonie]

commit e5e21f70bfd3 ("regulator: core: Take lock before applying system
load") took the regulator lock before calling drms_uA_update() in order
to silence a lockdep warning during regulator_register().

However, we are not supposed to need locks at this point as the regulator
is in the process of being registered, so there should be no possibility
of concurrent access.

Instead, remove the unnecessary locking and simply drop the lockdep
annotation, since it is no longer valid.

Fixes: e5e21f70bfd3 ("regulator: core: Take lock before applying system load")
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: da9063: Convert to use regulator_set/get_current_limit_regmap

Use regulator_set/get_current_limit_regmap helpers to save some code.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Steve Twiss <stwiss@opensource.diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: da9062: Convert to use regulator_set/get_current_limit_regmap

Use regulator_set/get_current_limit_regmap helpers to save some code.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Steve Twiss <stwiss@opensource.diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: lp87565: Convert to use regulator_set/get_current_limit_regmap

Use regulator_set/get_current_limit_regmap helpers to save some code.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: lp87565: Fix missing register for LP87565_BUCK_0

LP87565_BUCK_0 is missed, fix it.

Fixes: f0168a9bf ("regulator: lp87565: Add support for lp87565 PMIC regulators")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: mt6397: Use unsigned int for volt_tables

Make it consistent as .volt_table should be const unsigned int *.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: mt6380: Use unsigned int for volt_tables

Make it consistent as .volt_table should be const unsigned int *.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: mt6323: Use unsigned int for volt_tables

Make it consistent as .volt_table should be const unsigned int *.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>