Olof Johansson [Tue, 25 Jun 2019 11:48:32 +0000 (04:48 -0700)]
Merge tag 'tegra-for-5.3-arm64-dt' of git://git./linux/kernel/git/tegra/linux into arm/dt
arm64: tegra: Device tree changes for v5.3-rc1
This contains the bulk of the Tegra changes this cycle. It has a bunch
of improvements across almost all boards. These are mostly small and not
too exciting additions.
Most notably perhaps is the continuation of Jetson Nano support, which
is now mostly on feature parity with Jetson TX1.
* tag 'tegra-for-5.3-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (28 commits)
arm64: tegra: Enable PCIe slots in P2972-0000 board
arm64: tegra: Add P2U and PCIe controller nodes to Tegra194 DT
arm64: tegra: Add PEX DPD states as pinctrl properties
arm64: tegra: Enable ACONNECT, ADMA and AGIC
arm64: tegra: Add ACONNECT, ADMA and AGIC nodes
arm64: tegra: Sort device tree nodes alphabetically
arm64: tegra: Fix Jetson Nano GPU regulator
arm64: tegra: Update Jetson TX1 GPU regulator timings
arm64: tegra: Fix AGIC register range
arm64: tegra: Add INA3221 channel info for Jetson TX2
arm64: tegra: Enable PWM on Jetson Nano
arm64: tegra: Enable CPU sleep on Jetson Nano
arm64: tegra: Add ID EEPROMs on Jetson Nano
arm64: tegra: Add ID EEPROM for Jetson TX2 Developer Kit
arm64: tegra: Add ID EEPROM for Jetson TX2 module
arm64: tegra: Add ID EEPROM for Jetson TX1 Developer Kit
arm64: tegra: Add ID EEPROM for Jetson TX1 module
arm64: tegra: Don't use architected timer for suspend on Tegra210
arm64: tegra: Mark architected timer as always on
arm64: tegra: Add pin control states for I2C on Tegra186
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 25 Jun 2019 11:47:55 +0000 (04:47 -0700)]
Merge tag 'stm32-dt-for-v5.3-1' of git://git./linux/kernel/git/atorgue/stm32 into arm/dt
STM32 DT updates for v5.3, round 1
Highlights:
----------
MPU part:
-Add stm32mp157a-avenger board support:
This board embeds a STM32MP157a SOC with AC package (TFBGA361, 148 ios)
, 1024MB of DDR3 and STPMIC1A pmic . Several connections are available on this boards:
2x Type A (USB 2.0) Host and 1x Micro B (USB 2.0) OTG, ethernet
10/100/1000, WiFi 5 GHz & 2.4GHz, ...
-Add STMFX support en stm32mp157c-ev1 and enable joystick connected on
it.
-Add I2S and SAI support on stm32mp157c.
-Add and enable support of Vivante GPU on stm32mp157 ED1 and DK1 boards
(EV1 and DK2 inherit of it).
-Add camera support:
-Add DCMI support on stm32mp157c SOC
-Enabled OV5640 camera support on stm32mp157c-ev1 board
-Enable hdmi bridge sii9022 & display controller on stm32mp157c-dk1
board.
MCU part:
-Add STMFX support en stm32746g-eval and enable connections on it:
leds and joystick
* tag 'stm32-dt-for-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (27 commits)
ARM: dts: stm32: replace rgmii mode with rgmii-id on stm32mp15 boards
ARM: dts: stm32: Add Avenger96 devicetree support based on STM32MP157A
dt-bindings: arm: stm32: Document Avenger96 devicetree binding
dt-bindings: arm: stm32: Convert STM32 SoC bindings to DT schema
ARM: dts: stm32: Add missing pinctrl definitions for STM32MP157
ARM: dts: stm32: add sai id registers to stm32mp157c
ARM: dts: stm32: add power supply of rm68200 on stm32mp157c-ev1
ARM: dts: stm32: enable display on stm32mp157c-dk1 board
ARM: dts: stm32: Add I2C 1 config for stm32mp157a-dk1
ARM: dts: stm32: enable OV5640 camera on stm32mp157c-ev1 board
ARM: dts: stm32: add DCMI pins to stm32mp157c
ARM: dts: stm32: add DCMI camera interface support on stm32mp157c
ARM: dts: stm32: enable Vivante GPU support on stm32mp157a-dk1 board
ARM: dts: stm32: enable Vivante GPU support on stm32mp157c-ed1 board
ARM: dts: stm32: Add Vivante GPU support on STM32MP157c
ARM: dts: stm32: add i2s pins muxing on stm32mp157
ARM: dts: stm32: add i2s support on stm32mp157c
ARM: dts: stm32: add sai pins muxing on stm32mp157
ARM: dts: stm32: add sai support on stm32mp157c
ARM: dts: stm32: add jedec compatible for nor flash on stm32mp157c-ev1
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 25 Jun 2019 11:47:08 +0000 (04:47 -0700)]
Merge tag 'mvebu-dt64-5.3-1' of git://git.infradead.org/linux-mvebu into arm/dt
mvebu dt64 for 5.3 (part 1)
For Armada 7K/8K:
- enable AP806 thermal throttling with CPUfreq
- add missing #interrupt-cells property allowing configuring
interrupt for GPIO
On Armada 8040 based board:
- Fix PCI memory window on Mcbin board
- Set SFP power limit on clearfog GT board
- Disable AP I2C on Armada-8040-DB
On Armada 3720 based board espressobin correct the SPI node used for
NOR flash
On Armada 7040 DB board add USB current regulators
* tag 'mvebu-dt64-5.3-1' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: add missing #interrupt-cells property
arm64: dts: marvell: armada-7040-db: Add USB current regulators
arm64: dts: armada-3720-espressobin: correct spi node
arm64: dts: marvell: Disable AP I2C on Armada-8040-DB
arm64: dts: marvell: Enable AP806 thermal throttling with CPUfreq
arm64: dts: marvell: Change core numbering in AP806 thermal-node
arm64: dts: marvell: clearfog-gt-8k: set SFP power limit
arm64: dts: marvell: mcbin: enlarge PCI memory window
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 25 Jun 2019 11:46:25 +0000 (04:46 -0700)]
Merge tag 'mvebu-dt-5.3-1' of git://git.infradead.org/linux-mvebu into arm/dt
mvebu dt for 5.3 (part 1)
Add LCD support on Netgear RN104
* tag 'mvebu-dt-5.3-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada: netgear-rn104: Add LCD to RN104 dts.
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 25 Jun 2019 11:45:45 +0000 (04:45 -0700)]
Merge tag 'renesas-arm64-dt-for-v5.3' of https://git./linux/kernel/git/horms/renesas into arm/dt
Renesas ARM64 Based SoC DT Updates for v5.3
* Renesas SoCs
- Revise usb2_phy nodes and phys properties according to updated bindings
- Use ip=on for bootargs
* R-Car Gen 3 and RZ/G2M (r8a774a1) SoCs
- Add dynamic power coefficient
- Create thermal zone to support IPA
* R-Car E3 (r8a77990) and D3 (r8a77995) SoCs
- Point LVDS0 to its companion LVDS1
* R-Car E3 (r8a77990) SoC
- Corresct register range of DU
* R-Car E3 (r8a77990) based Ebisu board
- Remove renesas, no-ether-link property
* R-Car D3 (r8a77995) based Draak board:
- Remove unnecessary index from vin4 port
* RZ/G2M (r8a774a1) based HiHope main and sub-boards:
- Initial support
- Describe CPU capacity and topoligy
- Enable CMT, HDMI, LEDs, PCIe RWDT, SCIF, SDHI, TMU, and USB 2.0 and 3.0
* RZ/G2E (r8a774c0) SoC based EK874 board:
- Clean up CPU compatible strings
- Enable: Bluetooth, HDMI audio and video, TPU, USB 3.0 and WLAN
* tag 'renesas-arm64-dt-for-v5.3' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (53 commits)
arm64: dts: renesas: hihope-common: Remove "label" from LEDs
arm64: dts: renesas: hihope-common: Add HDMI support
arm64: dts: renesas: r8a774a1: Add HDMI encoder instance
arm64: dts: renesas: r8a774a1: Add dynamic power coefficient
arm64: dts: renesas: r8a774a1: Create thermal zone to support IPA
arm64: dts: renesas: r8a774a1: Add CPU capacity-dmips-mhz
arm64: dts: renesas: r8a774a1: Add CPU topology on r8a774a1 SoC
arm64: dts: renesas: hihope-common: Add LEDs support
arm64: dts: renesas: hihope-common: Enable USB3.0
arm64: dts: renesas: hihope-common: Add USB 2.0 support
arm64: dts: renesas: r8a774a1: Fix USB 2.0 clocks
arm64: dts: renesas: r8a774a1: Add TMU device nodes
arm64: dts: renesas: r8a774a1: Add CMT device nodes
arm64: dts: renesas: hihope-common: Add uSD and eMMC
arm64: dts: renesas: r8a77990: Fix register range of display node
arm64: dts: renesas: cat874: Enable usb role switch support
arm64: dts: renesas: cat874: Enable USB3.0 host/peripheral device node
arm64: dts: renesas: r8a7799[05]: Point LVDS0 to its companion LVDS1
arm64: dts: renesas: hihope-common: Add RWDT support
arm64: dts: renesas: hihope-rzg2-ex: Enable PCIe support
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 25 Jun 2019 11:44:18 +0000 (04:44 -0700)]
Merge tag 'renesas-arm-dt-for-v5.3' of https://git./linux/kernel/git/horms/renesas into arm/dt
Renesas ARM Based SoC DT Updates for v5.3
* Renesas SoC based boards
- Use ip=on for bootargs
* Renesas R-Car Gen 2 SOC based boards
- Configure PMIC IRQ pinmux
* R-Car V2H (r8a7792) SoC
- Describe CMT devices in DT
* RZ/G1C (r8a77470) based iWave SBC (iwg23s-sbc) and
RZ/G1N (r8a7744) based boards:
- Correct SDHI2 VccQ regulator to fix SDR50 mode
* RZ/A2M (r7s9210) based rza2mevb EVB
RZ/A1H (r7s72100) based rskrza1 board
- Describe input switch in DT
* RZ/A2M (r7s9210) based rza2mevb EVB
- Sort nodes to ease future maintenance
- Add USB host, Ethernet and SDHI support
* RZ/A2M (r7s9210) and RZ/A1H (r7s72100) SoCs
- Describe IRQC device in DT
* tag 'renesas-arm-dt-for-v5.3' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (22 commits)
ARM: dts: r8a7792: Add CMT0 and CMT1 to r8a7792
ARM: dts: iwg23s-sbc: Fix SDHI2 VccQ regulator
ARM: dts: iwg20d-q7-common: Fix SDHI1 VccQ regularor
ARM: dts: rza2mevb: Add input switch
ARM: dts: r7s9210: Add IRQC device node
ARM: dts: rza2mevb: sort nodes of rza2mevb board
ARM: dts: renesas: Use ip=on for bootargs
ARM: dts: rza2mevb: Add USB Host support
ARM: dts: r7s9210: Add USB Device support
ARM: dts: r7s9210: Add USB Host support
ARM: dts: rskrza1: Add input switches
ARM: dts: r7s72100: Add IRQC device node
ARM: dts: r8a779x: Configure PMIC IRQ pinmux
ARM: dts: rza2mevb: Add 48MHz USB clock
ARM: dts: r7s9210: Add USB clock
ARM: dts: rza2mevb: add ethernet aliases
ARM: dts: rza2mevb: Add SDHI support
ARM: dts: rza2mevb: Add Ethernet support
ARM: dts: r7s9210: Add SDHI support
ARM: dts: r7s9210: Add RIIC support
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 25 Jun 2019 11:43:29 +0000 (04:43 -0700)]
Merge tag 'renesas-dt-bindings-for-v5.3' of https://git./linux/kernel/git/horms/renesas into arm/dt
Renesas ARM Based SoC DT Bindings Updates for v5.3
* Renesas Gen3 DWC HDMI TX Encoder
- Add RZ/G2M (r8a774a1) support
* Renesas R-Car Compare Match Timer (CMT)
- Add R-Car H3 (r8a7795), M3-N (r8a77965) and E3 (r8a77990) support
* Renesas R-Car CAN FD Controller
- Add R-Car M3-N (r8a77965) and E3 (r8a77990), and RZ/G2E (r8a774c0) support
* Renesas R-Car CAN Controller
- Add RZ/G2M (r8a774a1) support
- Correct RZ/G2 clocks
* Vendor prefixes: Add vendor prefix for HopeRun
* Renesas SoCs and boards: Add HopeRun RZ/G2[M] boards
* tag 'renesas-dt-bindings-for-v5.3' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
dt-bindings: display: renesas: Add r8a774a1 support
dt-bindings: timer: renesas, cmt: Document r8a779{5|65|90} CMT support
dt-bindings: can: rcar_canfd: document r8a774c0 support
dt-bindings: can: rcar_canfd: document r8a77990 support
dt-bindings: can: rcar_canfd: document r8a77965 support
dt-bindings: can: rcar_can: Add r8a774c0 support
dt-bindings: can: rcar_can: Fix RZ/G2 CAN clocks
dt-bindings: Add vendor prefix for HopeRun
dt-bindings: arm: renesas: Add HopeRun RZ/G2[M] boards
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 25 Jun 2019 11:42:05 +0000 (04:42 -0700)]
Merge tag 'sunxi-h3-h5-for-5.3-
201906210812' of https://git./linux/kernel/git/sunxi/linux into arm/dt
This time we only have a single patch for our command branch between
arm and arm64, a fix for the array syntax raised by our DT schemas.
* tag 'sunxi-h3-h5-for-5.3-
201906210812' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sunxi: h3/h5: Fix GPIO regulator state array
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 25 Jun 2019 11:41:39 +0000 (04:41 -0700)]
Merge tag 'sunxi-dt64-for-5.3-
201906210808' of https://git./linux/kernel/git/sunxi/linux into arm/dt
Our usual bunch of arm64 DT changes, this time with:
- Some fixes for the DT schemas that were added during this release
- Wifi support for the H6
- LRADC suppport for the A64
- Some background work on A64 boards, to enable various devices such
as touchscreens, PMIC, audio, wifi, etc.
* tag 'sunxi-dt64-for-5.3-
201906210808' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: h6: Add DMA node
arm64: dts: allwinner: a64: Add lradc node
dt-bindings: input: sun4i-lradc-keys: Add A64 compatible
arm64: dts: allwinner: h6: add r_watchog node
arm64: dts: allwinner: h6: add watchdog node
dt-bindings: watchdog: add Allwinner H6 watchdog
arm64: dts: allwinner: a64: Enable audio on Teres-I
arm64: dts: allwinner: a64: bananapi-m64: Enable PMIC USB power supply
arm64: dts: allwinner: axp803: add USB power supply node
arm64: dts: allwinner: a64: Add pinmux for RGB666 LCD
arm64: dts: allwinner: a64: orangepi-win: Add wifi and bluetooth nodes
arm64: dts: allwinner: h6: add PIO VCC bank supplies for Pine H64
arm64: dts: allwinner: a64-oceanic-5205-5inmfd: Enable GT911 CTP
arm64: dts: allwinner: a64-amarula-relic: Add GT5663 CTP node
arm64: dts: allwinner: a64: move I2C pinctrl to dtsi
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 25 Jun 2019 11:40:52 +0000 (04:40 -0700)]
Merge tag 'sunxi-dt-for-5.3-
201906210807' of https://git./linux/kernel/git/sunxi/linux into arm/dt
Our usual bunch of patches:
- Some work on the BPi M2-Berry to support various devices
- Convert some bindings to a schema, and a lot of fixes reported by
the schemas we introduced.
- A few other fixes here and there
* tag 'sunxi-dt-for-5.3-
201906210807' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (21 commits)
dt-bindings: pwm: Convert Allwinner PWM to a schema
ARM: dts: sun8i: r40: Change the RTC compatible
ARM: dts: sun8i: v3s: Add external crystals accuracy
ARM: dts: sun8i: v3s: Fix the RTC node
ARM: dts: sun6i: Add external crystals accuracy
ARM: dts: sun6i: Fix RTC node
ARM: dts: sun8i: a83t: Add device node for CSI (Camera Sensor Interface)
ARM: dts: gr8-evb: Fix RTC vendor
ARM: dts: sun7i: icnova-swac: Fix the model vendor
ARM: dts: sun8i: a711: Change LRADC node names to avoid warnings
ARM: dts: sun7i: olimex-lime2: Enable ac and power supplies
ARM: dts: sun6i: Add default address and size cells for SPI
ARM: dts: sun8i-h3: Fix wifi in Beelink X2 DT
dt-bindings: bus: Convert Allwinner RSB to a schema
ARM: dts: sun8i: r40: bananapi-m2-ultra: Remove regulator-always-on
ARM: dts: sun8i: v40: bananapi-m2-berry: Add Bluetooth device node
ARM: dts: sun8i: v40: bananapi-m2-berry: Enable AHCI
ARM: dts: sun8i: v40: bananapi-m2-berry: Enable HDMI output
ARM: dts: sun8i: v40: bananapi-m2-berry: Enable GMAC ethernet controller
ARM: dts: sun8i: v40: bananapi-m2-berry: Add GPIO pin-bank regulator supplies
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 25 Jun 2019 11:38:23 +0000 (04:38 -0700)]
Merge tag 'amlogic-dt' of https://git./linux/kernel/git/khilman/linux-amlogic into arm/dt
ARM: dts: Amlogic updates for v5.3
- SPDX updates
- switch to generic ethernet PHY reset bindings
- add the canvas module
- mxiii-plus board: add regulators
* tag 'amlogic-dt' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM: dts: meson: switch to the generic Ethernet PHY reset bindings
ARM: dts: meson8b: update with SPDX Licence identifier
ARM: dts: meson8b-odroidc1: update with SPDX Licence identifier
ARM: dts: meson8b-mxq: update with SPDX Licence identifier
ARM: dts: meson8: update with SPDX Licence identifier
ARM: dts: meson8-minix-neo-x8: update with SPDX Licence identifier
ARM: dts: meson6: update with SPDX Licence identifier
ARM: dts: meson6-atv1200: update with SPDX Licence identifier
ARM: dts: meson: update with SPDX Licence identifier
ARM: dts: meson8b: mxq: improve support for the TRONFY MXQ S805
ARM: dts: meson8m2: mxiii-plus: add the supply for the Mali GPU
ARM: dts: meson8m2: mxiii-plus: rename the DCDC2 regulator
ARM: dts: meson8b: add the canvas module
ARM: dts: meson8m2: update the offset of the canvas module
ARM: dts: meson8: add the canvas module
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 25 Jun 2019 11:37:18 +0000 (04:37 -0700)]
Merge tag 'davinci-for-v5.3/dt' of git://git./linux/kernel/git/nsekhar/linux-davinci into arm/dt
This pull request adds CPUFreq support for DA850 boards in device-tree
boot using the generic CPUFREQ_DT driver.
* tag 'davinci-for-v5.3/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci_all_defconfig: Enable CPUFREQ_DT
ARM: dts: da850-evm: enable cpufreq
ARM: dts: da850-lcdk: enable cpufreq
ARM: dts: da850-lego-ev3: enable cpufreq
ARM: dts: da850: add cpu node and operating points to DT
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 25 Jun 2019 11:35:02 +0000 (04:35 -0700)]
Merge tag 'aspeed-5.3-devicetree' of git://git./linux/kernel/git/joel/aspeed into arm/dt
ASPEED device tree updates for 5.3
We have various device tree updates from the OpenBMC project to enable
bits and pieces in existing systems, notably updates to Google's Zaius.
There are some AST2500 machines under development:
* Lenovo Hr630
* IBM Swift
* Facebook YAMP
And some AST2400 machines that have been around but out of tree and have
now joined the party:
* YADRO VESNIN
* Microsoft Olympus
* tag 'aspeed-5.3-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed:
ARM: dts: aspeed: Enable video engine on romulus and wtherspoon
ARM: dts: aspeed: Add Inspur fp5280g2 BMC machine
ARM: dts: aspeed: Add YADRO VESNIN BMC
ARM: dts: aspeed: Add Microsoft Olympus BMC
ARM: dts: aspeed: Adding Lenovo Hr630 BMC
ARM: dts: aspeed: Add Facebook YAMP BMC
ARM: dts: aspeed: swift: Add pca9539 devices
ARM: dts: aspeed: Add Swift BMC machine
ARM: dts: aspeed: cmm: enable ehci host controllers
ARM: dts: aspeed: zaius: fixed I2C bus numbers for pcie slots
ARM: dts: aspeed: zaius: update 12V brick I2C address
ARM: dts: aspeed: zaius: add Infineon and Intersil regulators
ARM: dts: aspeed: quanta-q71: Enable p2a node
ARM: dts: aspeed: Add aspeed-p2a-ctrl node
ARM: dts: aspeed: Add Power9 and Power9 CFAM description
ARM: dts: aspeed: Rename flash-controller nodes
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 25 Jun 2019 11:32:08 +0000 (04:32 -0700)]
Merge tag 'qcom-dts-for-5.3' of git://git./linux/kernel/git/qcom/linux into arm/dt
Qualcomm Device Tree Changes for v5.3
* Add display support to MSM8974
* Add display, backlight, and touchscreen support to MSM8974 Hammerhead
* Update coresight bindings for MSM8974 and APQ8064
* tag 'qcom-dts-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
ARM: dts: qcom: msm8974-hammerhead: add support for display
ARM: dts: msm8974: add display support
ARM: dts: qcom: msm8974-hammerhead: add support for backlight
ARM: dts: qcom: msm8974-hammerhead: add touchscreen support
ARM: dts: qcom-msm8974: Update coresight DT bindings
ARM: dts: qcom-apq8064: Update coresight DT bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 25 Jun 2019 11:31:37 +0000 (04:31 -0700)]
Merge tag 'qcom-arm64-for-5.3' of git://git./linux/kernel/git/qcom/linux into arm/dt
Qualcomm ARM64 Updates for v5.3
* Switch to use second gen PON on PM8998
* Add PSCI cupidle states for MSM8996, MSM8998,and SDM845
* Add MSM8996 UFS phy reset controller
* Add propre cpu capacity scaling on MSM8996
* Fixups for APR domain, legacy clocks, and PSCI entry latency on MSM8996
* Enable SMMUs on MSM8996
* Add Dragonboard 845C
* Add Q6V5, GPU, GMU, and AOSS QMP node on SDM845
* Fixup CPU topology on SDM845
* Change USB1 to be peripheral on SDM845 MTP
* Add PCIe Phy, RC nodes, ANOC1 SMMU, and RPMPD node on MSM8998
* Update coresight bindings for MSM8916
* Update idle state names and entry-method on MSM8916
* Add PCIe, RPMPD, LPASS, Q6, TCSR, TuringCC, PSCI cpuidle states,
and CDSP on QCS404
* Add reset-cells property to QCS404 GCC node
* Fixup s3 max voltage, l3 min voltage, drive strength typo, and
s3 supply definition on QCS404-evb
* Fixup ADC outputs and VADC calibration on PMS405
* tag 'qcom-arm64-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (39 commits)
arm64: dts: qcom: qcs404-evb: fix vdd_apc supply
arm64: dts: qcom: pm8998: Use qcom,pm8998-pon binding for second gen pon
arm64: dts: qcom: msm8996: Enable SMMUs
arm64: dts: qcom: msm8996: Correct apr-domain property
arm64: dts: qcom: Add Dragonboard 845c
arm64: dts: qcom: qcs404-evb: Enable PCIe
arm64: dts: qcom: qcs404: Add PCIe related nodes
arm64: dts: qcom: msm8998: Add PCIe PHY and RC nodes
arm64: dts: qcom: msm8998: Add ANOC1 SMMU node
arm64: dts: qcom: msm8996: Stop using legacy clock names
arm64: dts: msm8996: fix PSCI entry-latency-us
arm64: dts: qcom: msm8998: Add PSCI cpuidle low power states
arm64: dts: qcom: sdm845: Add Q6V5 MSS node
arm64: dts: qcom: Add AOSS QMP node
arm64: dts: qcom-qcs404: Add reset-cells to GCC node
arm64: dts: qcom-msm8916: Update coresight DT bindings
arm64: dts: qcom: msm8998: Add rpmpd node
arm64: dts: qcom: qcs404: Add rpmpd node
arm64: dts: qcom: qcs404: Move lpass and q6 into soc
arm64: dts: qcom: qcs404: Fully describe the CDSP
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 25 Jun 2019 11:30:50 +0000 (04:30 -0700)]
Merge tag 'hisi-arm32-dt-for-5.3' of git://github.com/hisilicon/linux-hisi into arm/dt
ARM: DT: Hisilicon ARM32 SoCs updates for v5.3
- Updated CoreSight funnel and replicator using new bindings to fix warning
for the hip04.
* tag 'hisi-arm32-dt-for-5.3' of git://github.com/hisilicon/linux-hisi:
ARM: dts: hip04: Update coresight DT bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 25 Jun 2019 11:30:13 +0000 (04:30 -0700)]
Merge tag 'hisi-arm64-dt-for-5.3' of git://github.com/hisilicon/linux-hisi into arm/dt
ARM64: DT: Hisilicon SoCs DT updates for v5.3
* Hi3660 SoC and related boards:
- Added CoreSight trace components
* Hi6220 SoC and related boards:
- Updated CoreSight funnel and replicator using new bindings to fix warning
* tag 'hisi-arm64-dt-for-5.3' of git://github.com/hisilicon/linux-hisi:
arm64: dts: hi3660: Add CoreSight support
arm64: dts: hi6220: Update coresight DT bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 25 Jun 2019 11:15:53 +0000 (04:15 -0700)]
Merge tag 'arm-soc/for-5.3/devicetree-v2' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contain Broadcom ARM-based SoCs Device Tree changes
for 5.3 please pull the following:
- Lukas enables DMA support for the BCM2835 (Raspberry Pi) SPI
controller
- Florian fixes a number of dtc W=1 warnings in the Broadcom DTS files
and provides a fix for devices failing to boot after the removal of
skelton.dtsi (that commit has been submitted as a separate fix)
* tag 'arm-soc/for-5.3/devicetree-v2' of https://github.com/Broadcom/stblinux:
ARM: dts: BCM5301X: Fix most DTC W=1 warnings
ARM: dts: NSP: Fix the bulk of W=1 DTC warnings
ARM: dts: BCM63xx: Fix DTC W=1 warnings
ARM: dts: BCM53573: Fix DTC W=1 warnings
ARM: dts: bcm-mobile: Fix most DTC W=1 warnings
ARM: dts: Cygnus: Fix most DTC W=1 warnings
ARM: dts: Fix BCM7445 DTC warnings
ARM: bcm283x: Enable DMA support for SPI controller
ARM: dts: bcm: Add missing device_type = "memory" property
Signed-off-by: Olof Johansson <olof@lixom.net>
Florian Fainelli [Tue, 28 May 2019 23:01:33 +0000 (16:01 -0700)]
ARM: dts: BCM5301X: Fix most DTC W=1 warnings
Fix the bulk of the unit_address_vs_reg warnings and unnecessary
\#address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Florian Fainelli [Tue, 28 May 2019 23:01:34 +0000 (16:01 -0700)]
ARM: dts: NSP: Fix the bulk of W=1 DTC warnings
Fix the bulk of the unit_address_vs_reg warnings and unnecessary
\#address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Florian Fainelli [Tue, 28 May 2019 23:01:32 +0000 (16:01 -0700)]
ARM: dts: BCM63xx: Fix DTC W=1 warnings
Fix the bulk of the unit_address_vs_reg warnings and unnecessary
\#address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Florian Fainelli [Tue, 28 May 2019 23:01:31 +0000 (16:01 -0700)]
ARM: dts: BCM53573: Fix DTC W=1 warnings
Fix the the unit_address_vs_reg warnings and unnecessary
\#address-cells/#size-cells without "ranges" or child "reg" property
warnings.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Florian Fainelli [Tue, 28 May 2019 23:01:30 +0000 (16:01 -0700)]
ARM: dts: bcm-mobile: Fix most DTC W=1 warnings
Fix the bulk of the unit_address_vs_reg warnings and unnecessary
\#address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Florian Fainelli [Tue, 28 May 2019 23:01:29 +0000 (16:01 -0700)]
ARM: dts: Cygnus: Fix most DTC W=1 warnings
Fix the bulk of the unit_address_vs_reg warnings and unnecessary
\#address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Florian Fainelli [Tue, 28 May 2019 23:01:28 +0000 (16:01 -0700)]
ARM: dts: Fix BCM7445 DTC warnings
Fixes a number of unit_address_vs_reg warnings:
DTC arch/arm/boot/dts/bcm7445-bcm97445svmb.dtb
arch/arm/boot/dts/bcm7445.dtsi:66.6-225.4: Warning (unit_address_vs_reg): /rdb: node has a reg or ranges property, but no unit name
arch/arm/boot/dts/bcm7445.dtsi:227.21-298.4: Warning (unit_address_vs_reg): /memory_controllers: node has a reg or ranges property, but no unit name
arch/arm/boot/dts/bcm7445-bcm97445svmb.dts:9.9-14.4: Warning (unit_address_vs_reg): /memory: node has a reg or ranges property, but no unit name
arch/arm/boot/dts/bcm7445.dtsi:255.10-275.5: Warning (simple_bus_reg): /memory_controllers/memc@1: simple-bus unit address format error, expected "80000"
arch/arm/boot/dts/bcm7445.dtsi:277.10-297.5: Warning (simple_bus_reg): /memory_controllers/memc@2: simple-bus unit address format error, expected "100000"
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Florian Fainelli [Mon, 3 Jun 2019 18:59:51 +0000 (11:59 -0700)]
Merge tag 'tags/bcm2835-dt-next-2019-06-01' into devicetree/next
This pull requests enables DMA support for the main SPI controller
on all Raspberry Pis.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Lukas Wunner [Thu, 9 May 2019 17:03:00 +0000 (19:03 +0200)]
ARM: bcm283x: Enable DMA support for SPI controller
Without this, the driver for the BCM2835 SPI controller uses interrupt
mode instead of DMA mode, incurring a significant performance penalty.
The Foundation's device tree has had these attributes for years, but for
some reason they were never upstreamed.
They were originally contributed by Noralf Trønnes and Martin Sperl:
https://github.com/raspberrypi/linux/commit/
25f3e064afc8
https://github.com/raspberrypi/linux/commit/
e0edb52b47e6
The DREQ numbers 6 and 7 are documented in section 4.2.1.3 of:
https://www.raspberrypi.org/app/uploads/2012/02/BCM2835-ARM-Peripherals.pdf
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Cc: Martin Sperl <kernel@martin.sperl.org>
Cc: Noralf Trønnes <noralf@tronnes.org>
Christophe Roullier [Mon, 17 Jun 2019 08:50:18 +0000 (10:50 +0200)]
ARM: dts: stm32: replace rgmii mode with rgmii-id on stm32mp15 boards
On disco and eval board, Tx and Rx delay are applied (pull-up of 4.7k
put on VDD) so which correspond to RGMII-ID mode with internal RX and TX
delays provided by the PHY, the MAC should not add the RX or TX delays
in this case
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Manivannan Sadhasivam [Wed, 12 Jun 2019 07:54:51 +0000 (13:24 +0530)]
ARM: dts: stm32: Add Avenger96 devicetree support based on STM32MP157A
Add devicetree support for Avenger96 board based on STM32MP157A MPU
from ST Micro. This board is one of the 96Boards Consumer Edition board
from Arrow Electronics and has the following features:
SoC: STM32MP157AAC
PMIC: STPMIC1A
RAM: 1024 Mbyte @ 533MHz
Storage: eMMC v4.51: 8 Gbyte
microSD Socket: UHS-1 v3.01
Ethernet Port: 10/100/1000 Mbit/s, IEEE 802.3 Compliant
Wireless: WiFi 5 GHz & 2.4GHz IEEE 802.11a/b/g/n/ac
Bluetooth®v4.2 (BR/EDR/BLE)
USB: 2x Type A (USB 2.0) Host and 1x Micro B (USB 2.0) OTG
Display: HDMI: WXGA (1366x768)@ 60 fps, HDMI 1.4
LED: 4x User LED, 1x WiFi LED, 1x BT LED
More information about this board can be found in 96Boards website:
https://www.96boards.org/product/avenger96/
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Manivannan Sadhasivam [Wed, 12 Jun 2019 07:54:50 +0000 (13:24 +0530)]
dt-bindings: arm: stm32: Document Avenger96 devicetree binding
This commit documents Avenger96 devicetree binding based on
STM32MP157 SoC.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Manivannan Sadhasivam [Wed, 12 Jun 2019 07:54:49 +0000 (13:24 +0530)]
dt-bindings: arm: stm32: Convert STM32 SoC bindings to DT schema
This commit converts STM32 SoC bindings to DT schema using jsonschema.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Manivannan Sadhasivam [Wed, 12 Jun 2019 07:54:48 +0000 (13:24 +0530)]
ARM: dts: stm32: Add missing pinctrl definitions for STM32MP157
Add missing pinctrl definitions for STM32MP157 MPU.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Olivier Moysan [Tue, 11 Jun 2019 11:45:56 +0000 (13:45 +0200)]
ARM: dts: stm32: add sai id registers to stm32mp157c
Add identification registers to address range
of SAI DT parent node, for stm32mp157c.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Yannick Fertré [Tue, 21 May 2019 15:03:18 +0000 (17:03 +0200)]
ARM: dts: stm32: add power supply of rm68200 on stm32mp157c-ev1
This patch adds a new property (power-supply) to panel rm68200 (raydium)
on stm32mp157c-ev1.
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Vidya Sagar [Wed, 12 Jun 2019 09:53:36 +0000 (15:23 +0530)]
arm64: tegra: Enable PCIe slots in P2972-0000 board
Enable PCIe controller nodes to enable respective PCIe slots on
P2972-0000 board. Following is the ownership of slots by different
PCIe controllers.
Controller-0 : M.2 Key-M slot
Controller-1 : On-board Marvell eSATA controller
Controller-3 : M.2 Key-E slot
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Vidya Sagar [Wed, 12 Jun 2019 09:53:35 +0000 (15:23 +0530)]
arm64: tegra: Add P2U and PCIe controller nodes to Tegra194 DT
Add P2U (PIPE to UPHY) and PCIe controller nodes to device tree.
The Tegra194 SoC contains six PCIe controllers and twenty P2U instances
grouped into two different PHY bricks namely High-Speed IO (HSIO-12 P2Us)
and NVIDIA High Speed (NVHS-8 P2Us) respectively.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Manikanta Maddireddy [Tue, 18 Jun 2019 18:02:02 +0000 (23:32 +0530)]
arm64: tegra: Add PEX DPD states as pinctrl properties
Add PEX deep power down states as pinctrl properties to set in PCIe driver.
In Tegra210, BIAS pads are not in power down mode when clamps are applied.
To set the pads in DPD, pass the PEX DPD states as pinctrl properties to
PCIe driver.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Sameer Pujar [Wed, 19 Jun 2019 11:51:22 +0000 (17:21 +0530)]
arm64: tegra: Enable ACONNECT, ADMA and AGIC
Enable ACONNECT, ADMA and AGIC devices on Jetson TX2 and Jetson AGX
Xavier.
Verified driver probe path and devices get registered fine.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Sameer Pujar [Wed, 19 Jun 2019 11:51:21 +0000 (17:21 +0530)]
arm64: tegra: Add ACONNECT, ADMA and AGIC nodes
Add device tree nodes for the ACONNECT, ADMA and AGIC devices on
Tegra186 and Tegra194.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Maxime Ripard [Thu, 16 May 2019 12:08:48 +0000 (14:08 +0200)]
dt-bindings: pwm: Convert Allwinner PWM to a schema
The Allwinner SoCs have a PWM controller supported in Linux, with a
matching Device Tree binding.
Now that we have the DT validation in place, let's convert the device tree
bindings for that controller over to a YAML schemas.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Magnus Damm [Mon, 17 Jun 2019 09:17:08 +0000 (18:17 +0900)]
ARM: dts: r8a7792: Add CMT0 and CMT1 to r8a7792
Add CMT0 and CMT1 to the R-Car Gen2 V2H (r8a7792) SoC.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Fabrizio Castro [Mon, 3 Jun 2019 09:53:52 +0000 (10:53 +0100)]
ARM: dts: iwg23s-sbc: Fix SDHI2 VccQ regulator
SDR50 isn't working anymore because the GPIO regulator
driver is using descriptors since
commit
d6cd33ad7102 ("regulator: gpio: Convert to use descriptors")
which in turn causes the system to use the polarity of the
GPIOs (as specified in the DT) for selecting the states,
but the polarity specified in the DT is wrong.
This patch fixes the regulator DT definition, and that fixes
SDR50.
Fixes: 9eb36b945b5c ("ARM: dts: iwg23s-sbc: Add uSD and eMMC support")
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Fabrizio Castro [Mon, 3 Jun 2019 09:53:51 +0000 (10:53 +0100)]
ARM: dts: iwg20d-q7-common: Fix SDHI1 VccQ regularor
SDR50 isn't working anymore because the GPIO regulator
driver is using descriptors since
commit
d6cd33ad7102 ("regulator: gpio: Convert to use descriptors")
which in turn causes the system to use the polarity of the
GPIOs (as specified in the DT) for selecting the states,
but the polarity specified in the DT is wrong.
This patch fixes the regulator DT definition, and that fixes
SDR50.
Fixes: 029efb3a03c5 ("ARM: dts: iwg20d-q7: Add SDHI1 support")
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Chris Brandt [Tue, 4 Jun 2019 20:09:14 +0000 (15:09 -0500)]
ARM: dts: rza2mevb: Add input switch
Add support for input switch SW3 on the Renesas RZ/A2M EVB
development board.
Note that this uses the IRQ interrupt, as the RZ/A2 GPIO controller
does not include interrupt support
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Chris Brandt [Tue, 4 Jun 2019 20:09:13 +0000 (15:09 -0500)]
ARM: dts: r7s9210: Add IRQC device node
Enable support for the IRQC on RZ/A2M, which is a small front-end to the
GIC. This allows to use up to 8 external interrupts with configurable
sense select.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Yoshihiro Kaneko [Fri, 17 May 2019 14:43:07 +0000 (23:43 +0900)]
ARM: dts: rza2mevb: sort nodes of rza2mevb board
This patch sorts the nodes of arch/arm/boot/dts/r7s9210-rza2mevb.dts.
* Sort subnodes of root ("/") node alphabetically
* Sort following top-level nodes alphabetically
* Sort subnodes of pinctrl alphabetically
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
[simon: rebase and sort new ehci nodes]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Magnus Damm [Sat, 18 May 2019 10:03:57 +0000 (19:03 +0900)]
ARM: dts: renesas: Use ip=on for bootargs
Convert bootargs from ip=dhcp to ip=on
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Martin Blumenstingl [Sat, 15 Jun 2019 10:38:30 +0000 (12:38 +0200)]
ARM: dts: meson: switch to the generic Ethernet PHY reset bindings
The snps,reset-gpio bindings are deprecated in favour of the generic
"Ethernet PHY reset" bindings.
Replace snps,reset-gpio from the ðmac node with reset-gpios in the
ethernet-phy node. The old snps,reset-active-low property is now encoded
directly as GPIO flag inside the reset-gpios property.
snps,reset-delays-us is converted to reset-assert-us and
reset-deassert-us. reset-assert-us is the second cell from
snps,reset-delays-us while reset-deassert-us was the third cell.
Instead of blindly copying the old values (which seems strange since
they gave the PHY one second to come out of reset) over this also
updates the delays based on the datasheets:
- RTL8211F PHY on the Odroid-C1 and MXIII-Plus needs a 10ms assert
delay (the datasheet mentions: "For a complete PHY reset, this pin
must be asserted low for at least 10ms") and a 30ms deassert delay
(the datasheet mentions: "Wait for a further 30ms (for internal
circuits settling time) before accessing the PHY register"). The
old settings used 10ms for assert and 1000ms for deassert.
- IP101GR PHY on the EC-100 and MXQ needs a 10ms assert delay (the
datasheet mentions: "Trst | Reset period | 10ms") and a 10ms deassert
delay as well (the datasheet mentions: "Tclk_MII_rdy | MII/RMII clock
output ready after reset released | 10ms")). The old settings used
10ms for assert and 1000ms for deassert.
No functional changes intended.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Thierry Reding [Thu, 20 Jun 2019 09:32:24 +0000 (11:32 +0200)]
arm64: tegra: Sort device tree nodes alphabetically
Device tree nodes without unit-address are to be sorted alphabetically.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Jon Hunter [Thu, 20 Jun 2019 08:17:02 +0000 (09:17 +0100)]
arm64: tegra: Fix Jetson Nano GPU regulator
There are a few issues with the GPU regulator defined for Jetson Nano
which are:
1. The GPU regulator is a PWM based regulator and not a fixed voltage
regulator.
2. The output voltages for the GPU regulator are not correct.
3. The regulator enable ramp delay is too short for the regulator and
needs to be increased. 2ms should be sufficient.
4. This is the same regulator used on Jetson TX1 and so make the ramp
delay and settling time the same as Jetson TX1.
Cc: stable@vger.kernel.org
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Fixes: 6772cd0eacc8 ("arm64: tegra: Add NVIDIA Jetson Nano Developer Kit support")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Jon Hunter [Thu, 20 Jun 2019 08:17:01 +0000 (09:17 +0100)]
arm64: tegra: Update Jetson TX1 GPU regulator timings
The GPU regulator enable ramp delay for Jetson TX1 is set to 1ms which
not sufficient because the enable ramp delay has been measured to be
greater than 1ms. Furthermore, the downstream kernels released by NVIDIA
for Jetson TX1 are using a enable ramp delay 2ms and a settling delay of
160us. Update the GPU regulator enable ramp delay for Jetson TX1 to be
2ms and add a settling delay of 160us.
Cc: stable@vger.kernel.org
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Fixes: 5e6b9a89afce ("arm64: tegra: Add VDD_GPU regulator to Jetson TX1")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Jon Hunter [Thu, 20 Jun 2019 08:17:00 +0000 (09:17 +0100)]
arm64: tegra: Fix AGIC register range
The Tegra AGIC interrupt controller is an ARM GIC400 interrupt
controller. Per the ARM GIC device-tree binding, the first address
region is for the GIC distributor registers and the second address
region is for the GIC CPU interface registers. The address space for
the distributor registers is 4kB, but currently this is incorrectly
defined as 8kB for the Tegra AGIC and overlaps with the CPU interface
registers. Correct the address space for the distributor to be 4kB.
Cc: stable@vger.kernel.org
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Fixes: bcdbde433542 ("arm64: tegra: Add AGIC node for Tegra210")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Nicolin Chen [Mon, 17 Jun 2019 22:16:59 +0000 (15:16 -0700)]
arm64: tegra: Add INA3221 channel info for Jetson TX2
There are four INA3221 chips on the Jetson TX2 (p3310 + p2771).
And each INA3221 chip has three input channels to monitor power.
So this patch adds these 12 channels to the DT of Jetson TX2, by
following the DT binding of INA3221 and official documents from
https://developer.nvidia.com/embedded/downloads
tegra186-p3310:
https://developer.nvidia.com/embedded/dlc/jetson-tx2-series-modules-oem-product-design-guide
tegra186-p2771-0000:
http://developer.nvidia.com/embedded/dlc/jetson-tx1-tx2-developer-kit-carrier-board-spec-
20180618
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Thierry Reding [Fri, 7 Jun 2019 14:01:11 +0000 (16:01 +0200)]
arm64: tegra: Enable PWM on Jetson Nano
Signed-off-by: Thierry Reding <treding@nvidia.com>
Eddie James [Tue, 2 Apr 2019 02:42:29 +0000 (02:42 +0000)]
ARM: dts: aspeed: Enable video engine on romulus and wtherspoon
Enable the video engine and add it's optional reserved memory region.
Use 32MB for the reserved memory since the video engine could need up to
two 1920x1200@32bpp source buffers.
Source buffers: 2 * 1920 * 1200 * 4 =
18432000 bytes
In addition, the V4L2 subsystem will allocate any number of compression
buffers, each at most 1/8th the size of the source buffer.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
John Wang [Thu, 13 Jun 2019 07:00:02 +0000 (15:00 +0800)]
ARM: dts: aspeed: Add Inspur fp5280g2 BMC machine
The fp5280g2 is an OpenPower server platform with an ASPEED AST2500 BMC.
Signed-off-by: John Wang <wangzqbj@inspur.com>
Reviewed-by: Lei YU <mine260309@gmail.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Jorge Ramirez-Ortiz [Wed, 19 Jun 2019 18:16:53 +0000 (20:16 +0200)]
arm64: dts: qcom: qcs404-evb: fix vdd_apc supply
The invalid definition in the supply causes the Qualcomm's EVB-1000
and EVB-4000 not to boot.
Fix the boot issue by correctly defining the supply: vdd_s3 (namely
"vdd_apc") is actually connected to vph_pwr.
Reported-by: Niklas Cassel <niklas.cassel@linaro.org>
Tested-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Olof Johansson [Wed, 19 Jun 2019 16:03:38 +0000 (09:03 -0700)]
Merge tag 'ti-k3-soc-for-v5.3' of git://git./linux/kernel/git/kristo/linux into arm/dt
Texas Instruments K3 SoC family changes for 5.3
- Add support for the new J721e SoC, includes basic peripherals needed for
booting up the device
- New peripheral support added for AM654x:
* TI SCI irqchip
* GPIO
* MCU SRAM
* R5Fs
* MSMC RAM
* SERDES and PCIe
* tag 'ti-k3-soc-for-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/kristo/linux: (26 commits)
arm64: dts: ti: k3-j721e: Add the MCU SRAM node
arm64: dts: ti: k3-j721e: Add interrupt controllers in wakeup domain
arm64: dts: ti: k3-j721e: Add interrupt controllers in main domain
arm64: dts: ti: k3-j721e-main: Add Main NavSS Interrupt controller node
arm64: defconfig: Enable TI's J721E SoC platform
arm64: dts: ti: Add support for J721E Common Processor Board
soc: ti: Add Support for J721E SoC config option
arm64: dts: ti: Add Support for J721E SoC
dt-bindings: serial: 8250_omap: Add compatible for J721E UART controller
dt-bindings: arm: ti: Add bindings for J721E SoC
arm64: dts: ti: am654-base-board: Disable SERDES and PCIe
arm64: dts: k3-am6: Add PCIe Endpoint DT node
arm64: dts: k3-am6: Add PCIe Root Complex DT node
arm64: dts: k3-am6: Add SERDES DT node
arm64: dts: k3-am6: Add mux-controller DT node required for muxing SERDES
arm64: dts: k3-am6: Add "socionext,synquacer-pre-its" property to gic_its
arm64: dts: ti: k3-am65: Add MSMC RAM ranges in interconnect node
arm64: dts: ti: k3-am65: Add R5F ranges in interconnect nodes
arm64: dts: ti: k3-am65-mcu: Add the MCU RAM node
arm64: dts: ti: k3-am65: Add MCU SRAM ranges in interconnect nodes
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Wed, 19 Jun 2019 16:00:58 +0000 (09:00 -0700)]
Merge tag 'socfpga_dts_updates_for_v5.3' of git://git./linux/kernel/git/dinguyen/linux into arm/dt
SoCFPGA DTS updates for v5.3
- Use the new "altr,socfpga-stmmac-a10-s10" for the EMAC controllers on
Arria10/Stratix10
- Add the ltc2497 i2c entry on the Arria10 devkit
- Add the EMAC OCP reset property on the Arria10
* tag 'socfpga_dts_updates_for_v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: dts: arria10: Add EMAC OCP reset property
ARM: dts: socfpga: add ltc2497 on arria10 devkit
arm64: dts: stratix10: use the "altr,socfpga-stmmac-a10-s10" binding
ARM: dts: socfpga: use the "altr,socfpga-stmmac-a10-s10" binding
Signed-off-by: Olof Johansson <olof@lixom.net>
Thierry Reding [Fri, 14 Jun 2019 15:41:04 +0000 (17:41 +0200)]
arm64: tegra: Enable CPU sleep on Jetson Nano
Jetson Nano implements CPU sleep via PSCI, much like any of the other
Tegra X1 platforms. Enable the sleep states to allow the CPU to go into
lower power states when idle.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Thierry Reding [Thu, 6 Jun 2019 15:54:05 +0000 (17:54 +0200)]
arm64: tegra: Add ID EEPROMs on Jetson Nano
The Jetson Nano has two ID EEPROMs, one for the module and another for
the carrier board. Add both to the device tree so that they can be read
from at runtime.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Thierry Reding [Thu, 13 Jun 2019 16:53:29 +0000 (18:53 +0200)]
arm64: tegra: Add ID EEPROM for Jetson TX2 Developer Kit
There is an ID EEPROM on the Jetson TX2 carrier board, part of the
Jetson TX2 Developer Kit, that exposes information that can be used to
identify the carrier board. Add the device tree node so that operating
systems can access this EEPROM.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Thierry Reding [Thu, 13 Jun 2019 16:53:28 +0000 (18:53 +0200)]
arm64: tegra: Add ID EEPROM for Jetson TX2 module
There is an ID EEPROM in the Jetson TX2 module that stores various bits
of information to indentify the module. Add the device tree node so that
operating systems can access this EEPROM.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Thierry Reding [Thu, 13 Jun 2019 16:53:31 +0000 (18:53 +0200)]
arm64: tegra: Add ID EEPROM for Jetson TX1 Developer Kit
There is an ID EEPROM on the Jetson TX1 carrier board, part of the
Jetson TX1 Developer Kit, that exposes information that can be used to
identify the carrier board. Add the device tree node so that operating
systems can access this EEPROM.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Thierry Reding [Thu, 13 Jun 2019 16:53:30 +0000 (18:53 +0200)]
arm64: tegra: Add ID EEPROM for Jetson TX1 module
There is an ID EEPROM in the Jetson TX1 module that stores various bits
of information to indentify the module. Add the device tree node so that
operating systems can access this EEPROM.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Leo Yan [Wed, 8 May 2019 02:18:52 +0000 (10:18 +0800)]
ARM: dts: hip04: Update coresight DT bindings
CoreSight DT bindings have been updated, thus the old compatible strings
are obsolete and the drivers will report warning if DTS uses these
obsolete strings.
This patch switches to the new bindings for CoreSight dynamic funnel and
static replicator, so can dismiss warning during initialisation.
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Zhangfei Gao <zhangfei.gao@linaro.org>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Wanglai Shi [Sat, 20 Apr 2019 14:00:35 +0000 (22:00 +0800)]
arm64: dts: hi3660: Add CoreSight support
This patch adds DT bindings for the CoreSight trace components
on hi3660, which is used by 96boards Hikey960.
Signed-off-by: Wanglai Shi <shiwanglai@hisilicon.com>
Reviewed-and-tested-by: Leo Yan <leo.yan@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Leo Yan [Wed, 8 May 2019 02:18:58 +0000 (10:18 +0800)]
arm64: dts: hi6220: Update coresight DT bindings
CoreSight DT bindings have been updated, thus the old compatible strings
are obsolete and the drivers will report warning if DTS uses these
obsolete strings.
This patch switches to the new bindings for CoreSight dynamic funnel and
static replicator, so can dismiss warning during initialisation.
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Zhangfei Gao <zhangfei.gao@linaro.org>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Fabrizio Castro [Wed, 19 Jun 2019 14:11:24 +0000 (15:11 +0100)]
arm64: dts: renesas: hihope-common: Remove "label" from LEDs
Remove "label" properties from the LEDs device tree nodes, since
we don't have nice labels on the PCB.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Fabrizio Castro [Tue, 18 Jun 2019 15:18:39 +0000 (16:18 +0100)]
arm64: dts: renesas: hihope-common: Add HDMI support
Add HDMI support to the HiHope RZ/G2[MN] mother board common
dtsi.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Fabrizio Castro [Tue, 18 Jun 2019 15:18:38 +0000 (16:18 +0100)]
arm64: dts: renesas: r8a774a1: Add HDMI encoder instance
Add the HDMI encoder to the R8A774A1 DT in disabled state.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Fabrizio Castro [Tue, 18 Jun 2019 15:18:37 +0000 (16:18 +0100)]
dt-bindings: display: renesas: Add r8a774a1 support
Document RZ/G2M (R8A774A1) SoC bindings.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Olof Johansson [Wed, 19 Jun 2019 13:27:32 +0000 (06:27 -0700)]
Merge tag 'samsung-dt-5.3' of https://git./linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM changes for v5.3
1. Fixes for minor warnings.
2. Enable ADC on Exynos5410 Odroid XU board.
* tag 'samsung-dt-5.3' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Add ADC node to Exynos5410 and Odroid XU
ARM: dts: exynos: Raise maximum buck regulator voltages on Arndale Octa
ARM: dts: exynos: Move CPU OPP tables out of SoC node on Exynos5420
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Wed, 19 Jun 2019 13:27:01 +0000 (06:27 -0700)]
Merge tag 'vexpress-updates-5.3' of git://git./linux/kernel/git/sudeep.holla/linux into arm/dt
ARMv7 Vexpress updates for v5.3
1. Couple of updates switching to use new/updated bindings for CoreSight
dynamic funnel components and NOR flash partition type
2. Disable NOR flash on Vexpress TC2 platform as it conflicts with CPU
power management. This follows what we have on ARMv8 Juno platform
and is required after recent commit that enabled CFI NOR FLASH in
multi_v7 defconfig
* tag 'vexpress-updates-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
ARM: dts: vexpress: set the right partition type for NOR flash
arm: dts: vexpress-v2p-ca15_a7: disable NOR flash node by default
ARM: dts: vexpress-v2p-ca15_a7: update coresight DT bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Wed, 19 Jun 2019 13:26:35 +0000 (06:26 -0700)]
Merge tag 'juno-updates-5.3' of git://git./linux/kernel/git/sudeep.holla/linux into arm/dt
ARMv8 Juno updates for v5.3
Couple of updates switching to use new/updated bindings for CoreSight
dynamic funnel components and NOR flash partition type
* tag 'juno-updates-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: juno: set the right partition type for NOR flash
arm64: dts: juno: update coresight DT bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Wed, 19 Jun 2019 13:25:55 +0000 (06:25 -0700)]
Merge tag 'omap-for-v5.3/ti-sysc-dt-signed' of git://git./linux/kernel/git/tmlind/linux-omap into arm/dt
ti-sysc dts changes for v5.3
We can now drop the custom dts property "ti,hwmods" for drivers that
have the ti-sysc interconnect target module configured in dts.
Let's start with a minimal changes to omap4 uart and mmc. We use
omap4 as the starting point as it has runtime PM implemented and all
the omap variants after that are based on it with similar clkctrl
clock for the modules. More devices will be updated later on as they
get tested.
Note that these changes are based on the related ti-sysc driver
changes.
* tag 'omap-for-v5.3/ti-sysc-dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (21 commits)
ARM: dts: Drop legacy custom hwmods property for omap4 mmc
ARM: dts: Drop legacy custom hwmods property for omap4 uart
bus: ti-sysc: Detect uarts also on omap34xx
bus: ti-sysc: Do rstctrl reset handling in two phases
bus: ti-sysc: Add support for disabling module without legacy mode
bus: ti-sysc: Set ENAWAKEUP if available
bus: ti-sysc: Handle swsup idle mode quirks
bus: ti-sysc: Handle clockactivity for enable and disable
bus: ti-sysc: Enable interconnect target module autoidle bit on enable
bus: ti-sysc: Allow QUIRK_LEGACY_IDLE even if legacy_mode is not set
bus: ti-sysc: Make OCP reset work for sysstatus and sysconfig reset bits
bus: ti-sysc: Support 16-bit writes too
bus: ti-sysc: Add support for missing clockdomain handling
ARM: dts: dra71x: Disable usb4_tm target module
ARM: dts: dra71x: Disable rtc target module
ARM: dts: dra76x: Disable usb4_tm target module
ARM: dts: dra76x: Disable rtc target module
ARM: dts: dra76x: Update MMC2_HS200_MANUAL1 iodelay values
ARM: dts: am57xx-idk: Remove support for voltage switching for SD card
bus: ti-sysc: Handle devices with no control registers
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Wed, 19 Jun 2019 13:25:29 +0000 (06:25 -0700)]
Merge tag 'omap-for-v5.3/dt-signed' of git://git./linux/kernel/git/tmlind/linux-omap into arm/dt
dts changes for omap variants for v5.3
This series of changes improves support for few boards:
- configure another lcd type for logicpd torpedo devkit
- a series of updates for am335x phytec boards
- configure mmc card detect pin for am335x-baltos
* tag 'omap-for-v5.3/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-baltos: add support for MMC1 CD pin
ARM: dts: am335x-baltos: Fix PHY mode for ethernet
ARM: dts: Add support for phyBOARD-REGOR-AM335x
ARM: dts: am335x-pcm-953: Remove eth phy delay
ARM: dts: am335x-pcm-953: Update user led names
ARM: dts: am335x-phycore-som: Enable gpmc node in dts files
ARM: dts: am335x-phycore-som: Add emmc node
ARM: dts: am335x phytec boards: Remove regulator node
ARM: dts: Add LCD type 28 support to LogicPD Torpedo DM3730 devkit
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Wed, 19 Jun 2019 13:24:21 +0000 (06:24 -0700)]
Merge tag 'arm-soc/for-5.3/devicetree-arm64' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM64-based SoCs Device Tree changes
for 5.3, please pull the following:
- Pramod adds the Device Tree nodes for thermal support on Stingray
- Srinath adds the Device Tree nodes for both XHCI (host) and BDC
(device) modes
- Rayagonda adds the Device Tree node for slave I2C operation when
Stingray operates as a SmartNIC
* tag 'arm-soc/for-5.3/devicetree-arm64' of https://github.com/Broadcom/stblinux:
arm64: dts: Stingray: Add NIC i2c device node
arm64: dts: Add USB DT nodes for Stingray SoC
arm64: dts: stingray: Add Stingray Thermal DT support.
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Wed, 19 Jun 2019 13:22:43 +0000 (06:22 -0700)]
Merge tag 'v5.3-rockchip-dts64-1' of git://git./linux/kernel/git/mmind/linux-rockchip into arm/dt
PCIe for rockpro64, wifi+bt for Rock-PI4, spi for Rock960 family
and a fix for the yet unused isp-iommus.
* tag 'v5.3-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: add WiFi+BT support on ROCK Pi4 board
arm64: dts: rockchip: fix isp iommu clocks and power domain
arm64: dts: rockchip: Enable SPI1 on Ficus
arm64: dts: rockchip: Enable SPI0 and SPI4 on Rock960
arm64: dts: rockchip: add PCIe nodes on rk3399-rockpro64
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Wed, 19 Jun 2019 13:22:09 +0000 (06:22 -0700)]
Merge tag 'v5.3-rockchip-dts32-1' of git://git./linux/kernel/git/mmind/linux-rockchip into arm/dt
A lot more love for rk3288 in general and veyron specially with changes
all over the place.
* tag 'v5.3-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (21 commits)
ARM: dts: rockchip: Split GPIO keys for veyron into multiple devices
ARM: dts: rockchip: Add HDMI i2c unwedging for rk3288-veyron
ARM: dts: rockchip: Add unwedge pinctrl entries for dw_hdmi on rk3288
ARM: dts: rockchip: Switch to builtin HDMI DDC bus on rk3288-veyron
ARM: dts: rockchip: Add pin names for rk3288-veyron jaq, mickey, speedy
ARM: dts: rockchip: fix pwm-cells for rk3288's pwm3
ARM: dts: rockchip: Configure the GPU thermal zone for mickey
ARM: dts: rockchip: Use the GPU to cool CPU thermal zone of veyron mickey
ARM: dts: rockchip: remove GPU 500 MHz OPP on rk3288
ARM: dts: rockchip: Use GPU as cooling device for the GPU thermal zone of the rk3288
ARM: dts: rockchip: Add #cooling-cells entry for rk3288 GPU
ARM: dts: rockchip: Mark that the rk3288 timer might stop in suspend
ARM: dts: rockchip: Add pin names for rk3288-veyron-jerry
ARM: dts: rockchip: Add pin names for rk3288-veyron-minnie
ARM: dts: raise GPU trip point temperature for speedy to 80 degC
ARM: dts: rockchip: raise GPU trip point temperatures for veyron
ARM: dts: rockchip: raise CPU trip point temperature for veyron to 100 degC
ARM: dts: rockchip: Make rk3288-veyron-minnie run at hs200
ARM: dts: rockchip: Make rk3288-veyron-mickey's emmc work again
ARM: dts: rockchip: Remove bogus 'i2s_clk_out' from rk3288-veyron-mickey
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Andy Gross [Sun, 9 Jun 2019 04:19:32 +0000 (23:19 -0500)]
arm64: qcom: qcs404: Add reset-cells to GCC node
This patch adds a reset-cells property to the gcc controller on the QCS404.
Without this in place, we get warnings like the following if nodes reference
a gcc reset:
arch/arm64/boot/dts/qcom/qcs404.dtsi:261.38-310.5: Warning (resets_property):
/soc@0/remoteproc@b00000: Missing property '#reset-cells' in node
/soc@0/clock-controller@
1800000 or bad phandle (referred from resets[0])
also defined at arch/arm64/boot/dts/qcom/qcs404-evb.dtsi:82.18-84.3
DTC arch/arm64/boot/dts/qcom/qcs404-evb-4000.dtb
arch/arm64/boot/dts/qcom/qcs404.dtsi:261.38-310.5: Warning (resets_property):
/soc@0/remoteproc@b00000: Missing property '#reset-cells' in node
/soc@0/clock-controller@
1800000 or bad phandle (referred from resets[0])
also defined at arch/arm64/boot/dts/qcom/qcs404-evb.dtsi:82.18-84.3
Signed-off-by: Andy Gross <agross@kernel.org>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Baolin Wang [Tue, 4 Jun 2019 08:14:29 +0000 (16:14 +0800)]
arm64: dts: sprd: Add Spreadtrum SD host controller support
Add one Spreadtrum SD host controller to support eMMC card for Spreadtrum
SC9860 platform.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Wed, 19 Jun 2019 13:15:10 +0000 (06:15 -0700)]
Merge tag 'integrator-dts-v5.3-arm-soc' of git://git./linux/kernel/git/linusw/linux-integrator into arm/dt
DTS updates for the Integrator, target kernel v5.3.
* tag 'integrator-dts-v5.3-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: dts: vexpress: specify AFS partition
ARM: dts: realview: specify AFS partition
ARM: dts: versatile: specify AFS partition
ARM: dts: integrator: specify AFS partition
Signed-off-by: Olof Johansson <olof@lixom.net>
Suman Anna [Wed, 5 Jun 2019 16:34:33 +0000 (11:34 -0500)]
arm64: dts: ti: k3-j721e: Add the MCU SRAM node
Add the on-chip SRAM present within the MCU domain as a mmio-sram node.
The K3 J721E SoCs have 1 MB of such memory. Any specific memory range
within this RAM needed by a driver/software module ought to be reserved
using an appropriate child node.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Lokesh Vutla [Fri, 14 Jun 2019 14:50:01 +0000 (20:20 +0530)]
arm64: dts: ti: k3-j721e: Add interrupt controllers in wakeup domain
Wakeup domain in J721E SoC has an interrupt router connected to gpio
in wakeup domain. Add DT node for this interrupt router.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Lokesh Vutla [Fri, 14 Jun 2019 14:50:00 +0000 (20:20 +0530)]
arm64: dts: ti: k3-j721e: Add interrupt controllers in main domain
Main domain in J721E has the following interrupt controller instances:
- Main Domain GPIO Interrupt router connected to gpio in main domain.
- Under the Main Domain Navigator Subsystem(NAVSS)
- Main Navss Interrupt Router connected to main navss inta and mailboxes.
- Main Navss Interrupt Aggregator connected to main domain UDMASS
Add DT nodes for the interrupt controllers available in main domain.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Suman Anna [Fri, 31 May 2019 00:48:48 +0000 (19:48 -0500)]
arm64: dts: ti: k3-j721e-main: Add Main NavSS Interrupt controller node
Add the Interrupt controller node for the Interrupt Router present within
the Main NavSS module. This Interrupt Router can route 192 interrupts to
the GIC_SPI in 3 sets of 64 interrupts each. Note that the last set is
reserved for the host ID A72_3 for hypervisor usecases, so the node is
added only with 2 sets for the Linux kernel context (host id A72_2). This
is specified through the ti,sci-rm-range-girq property.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Nishanth Menon [Wed, 22 May 2019 16:19:21 +0000 (11:19 -0500)]
arm64: defconfig: Enable TI's J721E SoC platform
Enable J721E SoC support from TI.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Nishanth Menon [Wed, 22 May 2019 16:19:20 +0000 (11:19 -0500)]
arm64: dts: ti: Add support for J721E Common Processor Board
Add Support for J721E Common Processor board support.
The EVM architecture is as follows:
+------------------------------------------------------+
| +-------------------------------------------+ |
| | | |
| | Add-on Card 1 Options | |
| | | |
| +-------------------------------------------+ |
| |
| |
| +-------------------+ |
| | | |
| | SOM | |
| +--------------+ | | |
| | | | | |
| | Add-on | +-------------------+ |
| | Card 2 | | Power Supply
| | Options | | |
| | | | |
| +--------------+ | <---
+------------------------------------------------------+
Common Processor Board
Common Processor board is the baseboard that has most of the actual
connectors, power supply etc. A SOM (System on Module) is plugged on
to the common processor board and this contains the SoC, PMIC, DDR and
basic high speed components necessary for functionality. Add-n card
options add further functionality (such as additional Audio, Display,
networking options).
Note:
A) The minimum configuration required to boot up the board is System On
Module(SOM) + Common Processor Board.
B) Since there is just a single SOM and Common Processor Board, we are
maintaining common processor board as the base dts and SOM as the dtsi
that we include. In the future as more SOM's appear, we should move
common processor board as a dtsi and include configurations as dts.
C) All daughter cards beyond the basic boards shall be maintained as
overlays.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Nishanth Menon [Wed, 22 May 2019 16:19:19 +0000 (11:19 -0500)]
soc: ti: Add Support for J721E SoC config option
Add option to build J721E SoC specific components
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Nishanth Menon [Wed, 22 May 2019 16:19:18 +0000 (11:19 -0500)]
arm64: dts: ti: Add Support for J721E SoC
The J721E SoC belongs to the K3 Multicore SoC architecture platform,
providing advanced system integration to enable lower system costs
of automotive applications such as infotainment, cluster, premium
Audio, Gateway, industrial and a range of broad market applications.
This SoC is designed around reducing the system cost by eliminating
the need of an external system MCU and is targeted towards ASIL-B/C
certification/requirements in addition to allowing complex software
and system use-cases.
Some highlights of this SoC are:
* Dual Cortex-A72s in a single cluster, three clusters of lockstep
capable dual Cortex-R5F MCUs, Deep-learning Matrix Multiply Accelerator(MMA),
C7x floating point Vector DSP, Two C66x floating point DSPs.
* 3D GPU PowerVR Rogue 8XE GE8430
* Vision Processing Accelerator (VPAC) with image signal processor and Depth
and Motion Processing Accelerator (DMPAC)
* Two Gigabit Industrial Communication Subsystems (ICSSG), each with dual
PRUs and dual RTUs
* Two CSI2.0 4L RX plus one CSI2.0 4L TX, one eDP/DP, One DSI Tx, and
up to two DPI interfaces.
* Integrated Ethernet switch supporting up to a total of 8 external ports in
addition to legacy Ethernet switch of up to 2 ports.
* System MMU (SMMU) Version 3.0 and advanced virtualisation
capabilities.
* Upto 4 PCIe-GEN3 controllers, 2 USB3.0 Dual-role device subsystems,
16 MCANs, 12 McASP, eMMC and SD, UFS, OSPI/HyperBus memory controller, QSPI,
I3C and I2C, eCAP/eQEP, eHRPWM, MLB among other peripherals.
* Two hardware accelerator block containing AES/DES/SHA/MD5 called SA2UL
management.
* Configurable L3 Cache and IO-coherent architecture with high data throughput
capable distributed DMA architecture under NAVSS
* Centralized System Controller for Security, Power, and Resource
Management (DMSC)
See J721E Technical Reference Manual (SPRUIL1, May 2019)
for further details: http://www.ti.com/lit/pdf/spruil1
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Nishanth Menon [Wed, 22 May 2019 16:19:17 +0000 (11:19 -0500)]
dt-bindings: serial: 8250_omap: Add compatible for J721E UART controller
J721e uses a UART controller that is compatible with AM654 UART.
Introduce a specific compatible to help handle the differences if
necessary.
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Nishanth Menon [Wed, 22 May 2019 16:19:16 +0000 (11:19 -0500)]
dt-bindings: arm: ti: Add bindings for J721E SoC
The J721E SoC belongs to the K3 Multicore SoC architecture platform,
providing advanced system integration to enable lower system costs
of automotive applications such as infotainment, cluster, premium
Audio, Gateway, industrial and a range of broad market applications.
This SoC is designed around reducing the system cost by eliminating
the need of an external system MCU and is targeted towards ASIL-B/C
certification/requirements in addition to allowing complex software
and system use-cases.
Some highlights of this SoC are:
* Dual Cortex-A72s in a single cluster, three clusters of lockstep
capable dual Cortex-R5F MCUs, Deep-learning Matrix Multiply Accelerator(MMA),
C7x floating point Vector DSP, Two C66x floating point DSPs.
* 3D GPU PowerVR Rogue 8XE GE8430
* Vision Processing Accelerator (VPAC) with image signal processor and Depth
and Motion Processing Accelerator (DMPAC)
* Two Gigabit Industrial Communication Subsystems (ICSSG), each with dual
PRUs and dual RTUs
* Two CSI2.0 4L RX plus one CSI2.0 4L TX, one eDP/DP, One DSI Tx, and
up to two DPI interfaces.
* Integrated Ethernet switch supporting up to a total of 8 external ports in
addition to legacy Ethernet switch of up to 2 ports.
* System MMU (SMMU) Version 3.0 and advanced virtualisation
capabilities.
* Upto 4 PCIe-GEN3 controllers, 2 USB3.0 Dual-role device subsystems,
16 MCANs, 12 McASP, eMMC and SD, UFS, OSPI/HyperBus memory controller, QSPI,
I3C and I2C, eCAP/eQEP, eHRPWM, MLB among other peripherals.
* Two hardware accelerator block containing AES/DES/SHA/MD5 called SA2UL
management.
* Configurable L3 Cache and IO-coherent architecture with high data throughput
capable distributed DMA architecture under NAVSS
* Centralized System Controller for Security, Power, and Resource
Management (DMSC)
See J721E Technical Reference Manual (SPRUIL1, May 2019)
for further details: http://www.ti.com/lit/pdf/spruil1
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
John Stultz [Fri, 14 Jun 2019 23:14:51 +0000 (23:14 +0000)]
arm64: dts: qcom: pm8998: Use qcom,pm8998-pon binding for second gen pon
This changes pm8998 to use the new qcom,pm8998-pon compatible
string for the pon in order to support the gen2 pon
functionality properly.
Cc: Andy Gross <agross@kernel.org>
Cc: David Brown <david.brown@linaro.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Bjorn Andersson [Tue, 18 Jun 2019 05:23:46 +0000 (22:23 -0700)]
arm64: dts: qcom: msm8996: Enable SMMUs
Enable SMMUs on 8996 now that the WRZ workaround in the arm-smmu driver
has landed.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Bjorn Andersson [Tue, 18 Jun 2019 05:25:47 +0000 (22:25 -0700)]
arm64: dts: qcom: msm8996: Correct apr-domain property
The domain specifier was changed from using "reg" to "qcom,apr-domain",
update the dts accordingly.
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Bjorn Andersson [Tue, 18 Jun 2019 21:19:45 +0000 (14:19 -0700)]
arm64: dts: qcom: Add Dragonboard 845c
This adds an initial dts for the Dragonboard 845. Supported
functionality includes Debug UART, UFS, USB-C (peripheral), USB-A
(host), microSD-card and Bluetooth.
Initializing the SMMU is clearing the mapping used for the splash screen
framebuffer, which causes the board to reboot. This can be worked around
using:
fastboot oem select-display-panel none
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Tested-by: Vinod Koul <vkoul@kernel.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Biju Das [Wed, 12 Jun 2019 14:20:55 +0000 (15:20 +0100)]
arm64: dts: renesas: r8a774a1: Add dynamic power coefficient
Describe the dynamic power coefficient of A57 and A53 CPUs.
Based on work by Gaku Inami <gaku.inami.xw@bp.renesas.com> and others.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Biju Das [Wed, 12 Jun 2019 14:20:54 +0000 (15:20 +0100)]
arm64: dts: renesas: r8a774a1: Create thermal zone to support IPA
Setup a thermal zone driven by SoC temperature sensor. Create passive trip
points and bind them to CPUFreq cooling device that supports power
extension.
Based on work by Dien Pham <dien.pham.ry@renesas.com> for r8a7796 SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Biju Das [Wed, 12 Jun 2019 14:20:53 +0000 (15:20 +0100)]
arm64: dts: renesas: r8a774a1: Add CPU capacity-dmips-mhz
Set the capacity-dmips-mhz for RZ/G2M(r8a774a1) SoC, that is based on
dhrystone.
Based on work done by Gaku Inami <gaku.inami.xw@bp.renesas.com> for
r8a7796 SoC.
The average dhrystone result for 5 iterations is as below:
r8a774a1 SoC (CA57x2 + CA53x4)
CPU max-freq dhrystone
---------------------------------
CA57 1500 MHz
11428571 lps/s
CA53 1200 MHz
5000000 lps/s
From this, CPU capacity-dmips-mhz for CA57 and CA53 are calculated
as follows:
r8a774a1 SoC
CA57 : 1024 / (
11428571 / 1500) * (
11428571 / 1500) = 1024
CA53 : 1024 / (
11428571 / 1500) * (
5000000 / 1200) = 560
Since each CPUs have different max frequencies, the final CPU
capacities of A53 scaled by the above difference is as below
$ cat /sys/devices/system/cpu/cpu*/cpu_capacity
1024
1024
448
448
448
448
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
projects / openwrt / staging / blogic.git / log