drm/i915/guc:fix spelling mistake: "adddress" -> "address"

Trivial fix to spelling mistake in seq_printf message.

Fixes: a8b9370fc79c1 ("drm/i915/guc: Dump the GuC stage descriptor pool in debugfs")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170516092235.28640-1-colin.king@canonical.com

drm/i915/glk: Calculate high/low switch count for GLK

As per BSPEC, high/low switch count to be programmed in
terms of byteclock using exit_zero_count and prep_count.
For Geminilake exit/prep counts are already calculated
in terms of byteclock. This patch calculates high/low
switch count using counts value in byteclock, old calculation
leads to screen flicker/shift issue while resuming from S3/S4.

Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1494336565-19185-1-git-send-email-madhav.chauhan@intel.com

drm/i915: Fixup 64bit divides in timelines selftest

Some 64b divides snuck in when doing the prng timing compensation.

Fixes: 4797948071f6 ("drm/i915: Squash repeated awaits on the same fence")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170513094154.3581-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>

drm/i915: Update DRIVER_DATE to 20170515

Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915/perf: rate limit spurious oa report notice

This change is pre-emptively aiming to avoid a potential cause of kernel
logging noise in case some condition were to result in us seeing invalid
OA reports.

The workaround for the OA unit's tail pointer race condition is what
avoids the primary known cause of invalid reports being seen and with
that in place we aren't expecting to see this notice but it can't be
entirely ruled out.

Just in case some condition does lead to the notice then it's likely
that it will be triggered repeatedly while attempting to append a
sequence of reports and depending on the configured OA sampling
frequency that might be a large number of repeat notices.

v2: (Chris) avoid inconsistent warning on throttle with
    printk_ratelimit()
v3: (Matt) init and summarise with stream init/close not driver init/fini

Signed-off-by: Robert Bragg <robert@sixbynine.org>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170511154345.962-9-lionel.g.landwerlin@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915/perf: better pipeline aged/aging tail updates

This updates the tail pointer race workaround handling to updating the
'aged' pointer before looking to start aging a new one. There's the
possibility that there is already new data available and so we can
immediately start aging a new pointer without having to first wait for a
later hrtimer callback (and then another to age).

Signed-off-by: Robert Bragg <robert@sixbynine.org>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170511154345.962-8-lionel.g.landwerlin@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915/perf: improve invalid OA format debug message

A minor improvement to debugging output

Signed-off-by: Robert Bragg <robert@sixbynine.org>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170511154345.962-7-lionel.g.landwerlin@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915/perf: improve tail race workaround

There's a HW race condition between OA unit tail pointer register
updates and writes to memory whereby the tail pointer can sometimes get
ahead of what's been written out to the OA buffer so far (in terms of
what's visible to the CPU).

Although this can be observed explicitly while copying reports to
userspace by checking for a zeroed report-id field in tail reports, we
want to account for this earlier, as part of the _oa_buffer_check to
avoid lots of redundant read() attempts.

Previously the driver used to define an effective tail pointer that
lagged the real pointer by a 'tail margin' measured in bytes derived
from OA_TAIL_MARGIN_NSEC and the configured sampling frequency.
Unfortunately this was flawed considering that the OA unit may also
automatically generate non-periodic reports (such as on context switch)
or the OA unit may be enabled without any periodic sampling.

This improves how we define a tail pointer for reading that lags the
real tail pointer by at least %OA_TAIL_MARGIN_NSEC nanoseconds, which
gives enough time for the corresponding reports to become visible to the
CPU.

The driver now maintains two tail pointers:
 1) An 'aging' tail with an associated timestamp that is tracked until we
    can trust the corresponding data is visible to the CPU; at which point
    it is considered 'aged'.
 2) An 'aged' tail that can be used for read()ing.

The two separate pointers let us decouple read()s from tail pointer aging.

The tail pointers are checked and updated at a limited rate within a
hrtimer callback (the same callback that is used for delivering POLLIN
events) and since we're now measuring the wall clock time elapsed since
a given tail pointer was read the mechanism no longer cares about
the OA unit's periodic sampling frequency.

The natural place to handle the tail pointer updates was in
gen7_oa_buffer_is_empty() which is called as part of blocking reads and
the hrtimer callback used for polling, and so this was renamed to
oa_buffer_check() considering the added side effect while checking
whether the buffer contains data.

Signed-off-by: Robert Bragg <robert@sixbynine.org>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170511154345.962-6-lionel.g.landwerlin@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915/perf: no head/tail ref in gen7_oa_read

This avoids redundantly passing an (inout) head and tail pointer to
gen7_append_oa_reports() from gen7_oa_read which doesn't need to
reference either itself.

Moving the head/tail reads and writes into gen7_append_oa_reports should
have no functional effect except to avoid some redundant head pointer
writes in cases where nothing was copied to userspace.

This is a stepping stone towards updating how the head and tail pointer
state is managed to improve the workaround for the OA unit's tail
pointer race. It reduces the number of places we need to read/write the
head and tail pointers.

Signed-off-by: Robert Bragg <robert@sixbynine.org>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170511154345.962-5-lionel.g.landwerlin@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915/perf: avoid read back of head register

There's no need for the driver to keep reading back the head pointer
from hardware since the hardware doesn't update it automatically. This
way we can treat any invalid head pointer value as a software/driver
bug instead of spurious hardware behaviour.

This change is also a small stepping stone towards re-working how
the head and tail state is managed as part of an improved workaround
for the tail register race condition.

Signed-off-by: Robert Bragg <robert@sixbynine.org>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170511154345.962-4-lionel.g.landwerlin@intel.com

drm/i915/perf: avoid poll, read, EAGAIN busy loops

If the function for checking whether there is OA buffer data available
(during a poll or blocking read) has false positives then we want to
avoid a situation where the subsequent read() returns EAGAIN (after
a more accurate check) followed by a poll() immediately reporting
the same false positive POLLIN event and effectively maintaining a
busy loop until there really is data.

This makes sure that we clear the .pollin event status whenever we
return EAGAIN to userspace which will throttle subsequent POLLIN events
and repeated attempts to read to the 5ms intervals of the hrtimer
callback we have.

Signed-off-by: Robert Bragg <robert@sixbynine.org>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170511154345.962-3-lionel.g.landwerlin@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915/perf: fix gen7_append_oa_reports comment

If I'm going to complain about a back-to-front convention then the least
I can do is not muddle the comment up too.

Signed-off-by: Robert Bragg <robert@sixbynine.org>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170511154345.962-2-lionel.g.landwerlin@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915: Restore brightness level in aux backlight driver

Some panel will default to zero brightness when turning the
panel off and on again. This patch restores last brightness
level back when panel is turning back on.

Signed-off-by: Puthikorn Voravootivat <puthik@chromium.org>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170511230225.142870-8-puthik@chromium.org

drm/i915: Set backlight mode before enable backlight

We should set backlight mode register before set register to
enable the backlight.

Signed-off-by: Puthikorn Voravootivat <puthik@chromium.org>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170511230225.142870-6-puthik@chromium.org

drm/i915: Correctly enable backlight brightness adjustment via DPCD

intel_dp_aux_enable_backlight() assumed that the register
BACKLIGHT_BRIGHTNESS_CONTROL_MODE can only has value 01
(DP_EDP_BACKLIGHT_CONTROL_MODE_PRESET) when initialize.

This patch fixed that by handling all cases of that register.

Signed-off-by: Puthikorn Voravootivat <puthik@chromium.org>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170511230225.142870-3-puthik@chromium.org

drm/i915: Fix cap check for intel_dp_aux_backlight driver

intel_dp_aux_backlight driver should check for the
DP_EDP_BACKLIGHT_BRIGHTNESS_AUX_SET_CAP before enable the driver.

Signed-off-by: Puthikorn Voravootivat <puthik@chromium.org>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170511230225.142870-2-puthik@chromium.org

drm/i915: don't do allocate_va_range again on PIN_UPDATE

If a vma is already bound to a ppgtt, we incorrectly call
allocate_va_range again when doing a PIN_UPDATE, which will result in
over accounting within our paging structures, such that when we do
unbind something we don't actually destroy the structures and end up
inadvertently recycling them. In reality this probably isn't too bad,
but once we start touching PDEs and PDPEs for 64K/2M/1G pages this
apparent recycling will manifest into lots of really, really subtle
bugs.

v2: Fix the testing of vma->flags for aliasing_ppgtt_bind_vma

Fixes: ff685975d97f ("drm/i915: Move allocate_va_range to GTT")
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170512091423.26085-1-chris@chris-wilson.co.uk

drm/i915: set initialised only when init_context callback is NULL

During execlist_context_deferred_alloc() we presumed that the context is
uninitialised (we only just allocated the state object for it!) and
chose to optimise away the later call to engine->init_context() if
engine->init_context were NULL. This breaks with GVT's contexts that are
marked as pre-initialised to avoid us annoyingly calling
engine->init_context(). The fix is to not override ce->initialised if it
is already true.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1494497262-24855-1-git-send-email-chuanxiao.dong@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915: Do not sync RCU during shrinking

Due to the complex dependencies between workqueues and RCU, which
are not easily detected by lockdep, do not synchronize RCU during
shrinking.

On low-on-memory systems (mem=1G for example), the RCU sync leads
to all system workqueus freezing and unrelated lockdep splats are
displayed according to reports. GIT bisecting done by J. R.
Okajima points to the commit where RCU syncing was extended.

RCU sync gains us very little benefit in real life scenarios
where the amount of memory used by object backing storage is
dominant over the metadata under RCU, so drop it altogether.

 " Yeeeaah, if core could just, go ahead and reclaim RCU
   queues, that'd be great. "

  - Chris Wilson, 2016 (0eafec6d3244)

v2: More information to commit message.
v3: Remove "grep _rcu_" escapee from i915_gem_shrink_all (Andrea)

Fixes: c053b5a506d3 ("drm/i915: Don't call synchronize_rcu_expedited under struct_mutex")
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-by: J. R. Okajima <hooanon05g@gmail.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Hugh Dickins <hughd@google.com>
Tested-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: J. R. Okajima <hooanon05g@gmail.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: <stable@vger.kernel.org> # v4.11+
Link: http://patchwork.freedesktop.org/patch/msgid/1494414040-11160-1-git-send-email-joonas.lahtinen@linux.intel.com

drm/i915/guc: Make scratch register base and count flexible

We are using some scratch registers in MMIO based send function.
Make their base and count flexible in preparation of upcoming
GuC firmware/hardware changes. While around, change cmd len
parameter verification from WARN_ON to GEM_BUG_ON as we don't
need this all the time.

v2: call out WARN/GEM_BUG change in the commit msg (Daniele)
v3: don't overqualify the ints (Chris)
v4: rebase and use proper enum

Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Suggested-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

drm/i915/guc: Move notification code into virtual function

Prepare for alternate GuC notification mechanism.

Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
[Joonas: Added newlines]
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

drm/i915: Remove vma unpin in intel_plane_destroy

commit a667fb402c1e856209bf9e77ba41fc1cf356b867
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date:   Thu Dec 15 15:29:44 2016 +0100

    drm/i915: Disable all crtcs during driver unload, v2.

made sure that all crtc's are disabled on driver unload, but only the
following commit made sure all fb's are cleaned up correctly:

commit 9b2104f423de5c148749a07e8197dbab4c449877
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date:   Tue Feb 21 14:51:40 2017 +0100

    drm/atomic: Make disable_all helper fully disable the crtc.

Finally remove this and add a WARN_ON when vma is set. It should
have been removed by intel_cleanup_plane_fb().

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170511082844.13965-2-maarten.lankhorst@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Fix hw state verifier access to crtc->state.

We shouldn't inspect crtc->state, instead grab the crtc state.
At this point the hw state verifier should be able to run even if
crtc->state has been updated (which cannot currently happen).

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170511082844.13965-1-maarten.lankhorst@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915/guc: Dump the GuC stage descriptor pool in debugfs

We are missing pieces of information that could be useful for GuC
debugging.

v2: Reuse some code (Joonas)

Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
[Joonas: Removed extra newline and s/uint32_t/u32/ for checkpatch.pl]
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1494428691-20672-1-git-send-email-oscar.mateo@intel.com

drm/i915: Fix __intel_wait_for_register_fw to not sleep in atomic

The unconditionally fallback to the blocking wait_for resulted in
impressive fireworks at boot-up on my snb here. Make sure if we set
the slow timeout to 0 that we never ever sleep. The tail of the
callchain was

intel_wait_for_register
-> __intel_wait_for_register_fw
  -> usleep_range
     -> BOOM

It blew up in intel_crt_detect load detection code on the
ADPA_CRT_HOTPLUG_FORCE_TRIGGER in the ADPA register.

v2: Shut up gcc.

v3: Use uninitialized_var() (Chris).

Fixes: 0564654340e2 ("drm/i915: Acquire uncore.lock over intel_uncore_wait_for_register()")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1494429572-15118-1-git-send-email-daniel.vetter@ffwll.ch

drm/i915: Simplify cursor register write sequence

It looks like simply writing all the cursor register every single
time might be slightly faster than checking to see of each of
them need to be written. So if any other register apart from
CURPOS needs to be written let's just write all the registers.

CURPOS is left as a special case mainly for 845/865 where we have to
disable the cursor to change many of the cursor parameters. This
introduces a slight chance of the cursor flickering when things get
updated (since we're not currently doing the vblank evade for cursor
updates). If we write CURPOS alone then that obviously can't happen.
And let's follow the same pattern in the i9xx code just for symmetry.
I wasn't able to see a singificant performance difference between
this and just writing all the registers unconditionally.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170327185546.2977-16-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: Relax 845/865 CURBASE alignemnt requirement to 32 bytes

Supposedly 845/865 require only 32 byte alignment for CURBASE. Let's
relax the checks to allow that instead of demanding 4KiB alignment.
This will allow cursor panning in 8 pixel units.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170327185546.2977-15-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: Handle fb offset and src coordinates for cursors

The cursor plane doesn't have any kind of source offset register, so
the only form of panning possible is via a the base address register.
The alignment required by CURBASE ranges from 32B to 16KiB depending
on the platform. Let's make sure the user didn't ask for something
we can't do.

Obviously this is impossible to hit via the legacy cursor ioctl since
the src offsets are always 0, but via the plane/atomic ioctls the user
can ask for pretty much anything so we have to deal with this.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170327185546.2977-14-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: Fix gen3 physical cursor alignment requirements

Bspec tells us that gen3 platforms need 4KiB alignment for CURBASE
rather than the 256 byte alignment required by i85x. Let's fix that
and pull the code to determine the correct alignment to a helper
function.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170327185546.2977-13-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: Support variable cursor height on ivb+

IVB introduced the CUR_FBC_CTL register which allows reducing the cursor
height down to 8 lines from the otherwise square cursor dimensions.
Implement support for it. CUR_FBC_CTL can't be used when the cursor
is rotated.

Commandeer the otherwise unused cursor->cursor.size to track the
current value of CUR_FBC_CTL to optimize away redundant CUR_FBC_CTL
writes, and to notice when we need to arm the update via CURBASE if
just CUR_FBC_CTL changes.

v2: Reverse the gen check to make it sane
v3: Only enable CUR_FBC_CTL when cursor is enabled, adapt to
    earlier code changes which means we now actually turn off
    the cursor when we're supposed to unlike v2
v4: Add a comment about rotation vs. CUR_FBC_CTL,
    rebase due to 'dirty' (Chris)
v5: Rebase to the atomic world
    Handle 180 degree rotation
    Add HAS_CUR_FBC()
v6: Rebase
v7: Rebase due to I915_WRITE_FW/uncore.lock
    s/size/fbc_ctl/

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170327185546.2977-12-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: Use fb->pitches[0] in cursor code

The cursor code currently ignores fb->pitches[0] (except when creating
the fb itself), and just uses the cursor_width*4 as the stride. Let's
make sure fb->pitches[0] actually matches what we expect it to be.

We can also relax the stride vs. cursor width relationship on 845/865
since the stride is programmed separately. The only constraint is that
width*cpp doesn't exceed the stride, and that's already been checked
by the core since it makes sure the entire plane fits within the fb.

We can also drop the bo size check as that's already checked when
we create the fb. That is the fb is guaranteed to fit within the bo.

v2: Rebase due to i845_cursor_ctl() and i9xx_cursor_ctl()

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> #v1
Link: http://patchwork.freedesktop.org/patch/msgid/20170327185546.2977-11-ville.syrjala@linux.intel.com

drm/i915: Generalize cursor size checks a bit

We have the maximum cursor dimensions stored in the mode_config, so
let's just consult that information instead of hardcoding the same
information in multiple places.

We still need to keep some per-platform checks as the limitations are
quite diverse.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170327185546.2977-10-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: Split cursor check_plane into i845 and i9xx variants

The 845/865 and 830/855/9xx+ style cursor don't have that
much in common with each other, so let's just split the
.check_plane() hook into two variants as well.

v2: Keep the common stuff in one place (Chris)
v3: s/DRM_FORMAT_MOD_NONE/DRM_FORMAT_MOD_LINEAR/

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> #v1
Link: http://patchwork.freedesktop.org/patch/msgid/20170327185546.2977-9-ville.syrjala@linux.intel.com

drm/i915: Drop useless posting reads from cursor commit

There should be no need to do posting reads between all the cursor
register accessess. Let's just drop them.

v2: Rebase due to I915_WRITE_FW() and uncore.lock

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> #v1
Link: http://patchwork.freedesktop.org/patch/msgid/20170327185546.2977-8-ville.syrjala@linux.intel.com

drm/i915: Move cursor position and base handling into the platform specific functions

Supposedly on some platforms we can get extra atomicity guarantees for
CURPOS if we write it between the CURCNTR and CURBASE. Let's move the
CURPOS handling into the platform specific hooks to make the possible
without having to pass the calculated CURPOS around. And while at it,
do the same for the CURBASE to avoid passing that either.

v2: Use I915_WRITE_FW() and grab uncore.lock

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> #v1
Link: http://patchwork.freedesktop.org/patch/msgid/20170327185546.2977-7-ville.syrjala@linux.intel.com

drm/i915: Refactor CURPOS calculation

Move the CURPOS calculations to seprate function. This will allow
sharing the code between the 845/865 vs. others codepaths when we
otherwise split them apart.

v2: Don't pass intel_plane as it's not needed

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170327185546.2977-6-ville.syrjala@linux.intel.com

drm/i915: Clean up cursor junk from intel_crtc

Move cursor_base, cursor_cntl, and cursor_size from intel_crtc
into intel_plane so that we don't need the crtc for cursor stuff
so much.

Also entirely nuke cursor_addr which IMO doesn't provide any benefit
since it's not actually used by the cursor code itself. I'm not 100%
sure what the SKL+ DDB is code is after by looking at cursor_addr so
I just make it do its checks unconditionally. If that's not correct
then we should likely replace it with somehting like
plane_state->visible.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170327185546.2977-5-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: Refactor CURBASE calculation

The remaining cursor base address calculations are spread
around into several different locations. Just pull it all
into one place.

v2: Don't pass intel_plane as we don't really need it

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170327185546.2977-4-ville.syrjala@linux.intel.com

drm/i915: Pass intel_plane and intel_crtc to plane hooks

Streamline things by passing intel_plane and intel_crtc instead of
the drm types to our plane hooks.

v2: s/ilk/g4x/ in sprite code

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170327185546.2977-3-ville.syrjala@linux.intel.com

drm/i915: Parametrize cursor/primary pipe select bits

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170327185546.2977-2-ville.syrjala@linux.intel.com

drm/i915: Add support for sprites on g4x

Now that the watermarks are in order, it should be safe to enable sprite
planes on g4x. We alreday have the code in fact, we just call it ilk_.
Let's rename to g4x_ and let it loose.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170421181432.15216-16-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm/i915: Add g4x watermark tracepoint

Add a tracepoint for watermark programming on g4x, similar to what we
have on vlv/chv. Should help in debugging watermark programming sequence
issues.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170421181432.15216-15-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm/i915: Enable HPLL watermarks on g4x

I don't see why we couldn't use the HPLL watermarks on g4x. So let's
enable them. Let's assume a 35 usec memory latency for the HPLL mode.
That's roughly what PNV uses.

Based on the behaviour of the ELK box I have 35 usec is probably
overkill. Actually all the current latency values used seem overkill as
I can reduce them pretty drastically before I start to see underruns.
But let's play things a bit safe for now.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170421181432.15216-14-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm/i915: Two stage watermarks for g4x

Implement proper two stage watermark programming for g4x. As with
other pre-SKL platforms, the watermark registers aren't double
buffered on g4x. Hence we must sequence the watermark update
carefully around plane updates.

The code is quite heavily modelled on the VLV/CHV code, with some
fairly significant differences due to the different hardware
architecture:
* g4x doesn't use inverted watermark values
* CxSR actually affects the watermarks since it controls memory self
  refresh in addition to the max FIFO mode
* A further HPLL SR mode is possible with higher memory wakeup
  latency
* g4x has FBC2 and so it also has FBC watermarks
* max FIFO mode for primary plane only (cursor is allowed, sprite is not)
* g4x has no manual FIFO repartitioning
* some TLB miss related workarounds are needed for the watermarks

Actually the hardware is quite similar to ILK+ in many ways. The
most visible differences are in the actual watermakr register
layout. ILK revamped that part quite heavily whereas g4x is still
using the layout inherited from earlier platforms.

Note that we didn't previously enable the HPLL SR on g4x. So in order
to not introduce too many functional changes in this patch I've not
actually enabled it here either, even though the code is now fully
ready for it. We'll enable it separately later on.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170421181432.15216-13-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm/i915: Apply the g4x TLB miss w/a to SR watermarks as well

The documentation I've seen doesn't actually specify which watermarks
need the TLB miss w/a. Currently we only apply the w/a to the normal
watermarks for both primary and cursor planes. Since the documentation
doesn't explicitly say anything I'm going to assume that the w/a should
equally apply to the SR/HPLL watermarks. So let's do that.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170421181432.15216-12-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm/i915: Refactor wm calculations

All platforms until SKL compute their watermarks essentially
using the same method1/small buffer and method2/large buffer
formulas. Most just open code it in slightly different ways.
Let's pull it all into common helpers. This makes it a little
easier to spot the actual differences.

While at it try to add some docs explainign what the formulas
are trying to do.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170421181432.15216-11-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm/i915: Refactor the g4x TLB miss w/a to a helper

Pull the g4x TLB miss w/a calculation into a small helper.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170421181432.15216-10-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm/i915: Fix the g4x watermark TLB miss workaround

The g4x watermark TLB miss workaround requires that we bump up the
watermark by the difference between 8 full lines and the FIFO size.
Unfortunately the way we compute it at the moment ignores the size
of the pixels. The code also used the primary plane width as the
cursor width when computing the TLB miss w/a for the cursor.
Let's fix both problems.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170421181432.15216-9-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm/i915: Fix cursor 'cpp' in watermark calculatins for old platforms

The watermark code for the old platforms (g4x and older) uses the
primary plane cpp when computing cursor watermarks. To keep the fix
simple let's just hardcode cpp=4 for the cursor on those platforms
since that's all we support.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170421181432.15216-8-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm/i915: Document CxSR

Add some documentation explaining what CxSR actually is.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170421181432.15216-7-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm/i915: Make vlv/chv watermark debug print less cryptic

The magic numbers 0,1,2 aren't all that interesting for users perhaps.
Since we know what these watermark levels mean for VLV/CHV let's print
their names.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170421181432.15216-6-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm/i915: Rename bunch of vlv_ watermark structures to g4x_

We'll be wanting to share some of these watermark structures on g4x,
so let's rename them to have a g4x_ prefix instead of vlv_.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170421181432.15216-5-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm/i915: s/vlv_num_wm_levels/intel_wm_num_levels/

Rename the VLV/CHV max_level->num_levels helper to have an intel_
prefix since it's not VLV/CHV specific and I'll want to use it on
other platforms as well.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170421181432.15216-4-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm/i915: Drop the debug message from vlv_get_fifo_size()

Seeing the display FIFO sizes at driver load time doesn't really provide
anything useful for us, so let's just drop the debug message. One can
always use eg. intel_watermarks to dump out the hardware settings prior
to loading the driver.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170421181432.15216-3-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm/i915: s/vlv_plane_wm_compute/vlv_raw_plane_wm_compute/ etc.

Rename some of the vlv wm functions to reflect the fact that they
operate on the "raw" watermarks.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170421181432.15216-2-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm/i915/lvds: Remove magic from PLL programming

This looks like a left-over from enabling work. The spec defines
CH7017_LVDS_PLL_FEEDBACK_DEFAULT_RESERVED as reserved set, so follow
this in the programming.

v2:
- Follow the spec to set CH7017_LVDS_PLL_FEEDBACK_DEFAULT_RESERVED.
  (Ville)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1494408113-379-7-git-send-email-imre.deak@intel.com

drm/i915: Sanitize stolen memory size calculation

On GEN8+ (not counting CHV) the calculation can in theory result in an
incorrect sign extension with all upper bits set. In practice this is
unlikely to happen since it would require 4GB of stolen memory set
aside. For consistency still prevent the sign extension explicitly
everywhere.

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1494408113-379-6-git-send-email-imre.deak@intel.com

drm/i915: Check error return when converting pipe to connector

An error from intel_get_pipe_from_connector() would mean a bug somewhere
else, but we still should check for it to prevent some other more
obscure bug later.

v2:
- Fall back to a reasonable default instead of bailing out in case of
  error. (Jani)
v3:
- Fix s/PIPE_INVALID/INVALID_PIPE/ typo. (Jani)
v4:
- Fix bogus bracing around WARN() condition. (Ville)

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1494408113-379-5-git-send-email-imre.deak@intel.com

drm/i915: Check error return when setting DMA mask

Even though an error from these functions isn't fatal we still want to
have a diagnostic message about it.

v2:
- Don't do assignments in if statements. (Jani)

Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1494408113-379-4-git-send-email-imre.deak@intel.com

drm/i915/sdvo: Check error return from intel_sdvo_get_value()

The current code assumes that 'enhancements' won't change in case of an
error, but this isn't guaranteed. Fix things by treating any error as a
lack of the given capability.

v2:
- Remove the now redundant init of enhancements. (Ville)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1494408113-379-3-git-send-email-imre.deak@intel.com

drm/i915/dp: Check error return during DPCD capability queries

The assumptions of these users of drm_dp_dpcd_readb() is that the passed
in output buffer won't change in case of error, but this isn't
guaranteed. Fix this by treating any error as the lack of the given
capability.

In case of DP_SINK_DEVICE_AUX_FRAME_SYNC_CAP an error would leave the
buffer uninitialized even with the above assumption.

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1494408113-379-2-git-send-email-imre.deak@intel.com

drm/i915/vlv: Fix port B PLL opamp initialization

The current code looks like a typo, the specification calls for setting
bits 31:24 to 0x8C, while preserving bits 23:0. Fix things accordingly.

I'm not aware of the typo causing a real problem, so the fix is only for
consistency.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1494408113-379-1-git-send-email-imre.deak@intel.com

drm/i915: Show dmc debug registers on Kabylake

The assumption is that the registers offsets are
identical as with skl. Also all the published
kbl firmwares support the debug registers. So
let kbl show the debug counts.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100975
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1494324322-28193-1-git-send-email-mika.kuoppala@intel.com

drm/i915: Move uncore definitions into a separate header

In order to allow use of e.g. forcewake_domains in a other feature headers
included from the top of i915_drv.h, move all uncore related definitions
into their own header.

v2: move __mask_next_bit macro to utils header (Mika)

Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Suggested-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>

drm/i915: use memdup_user_nul

Use memdup_user_nul() helper instead of open-coding to simplify the
code.

Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/6baf3aa45d0b5e0fd016b508bac905ebf8443aac.1493779294.git.geliangtang@gmail.com

drm/i915: Fix rawclk readout for g4x

Turns out our skills in decoding the CLKCFG register weren't good
enough. On this particular elk the answer we got was 400 MHz when
in reality the clock was running at 266 MHz, which then caused us
to program a bogus AUX clock divider that caused all AUX communication
to fail.

Sadly the docs are now in bit heaven, so the fix will have to be based
on empirical evidence. Using another elk machine I was able to frob
the FSB frequency from the BIOS and see how it affects the CLKCFG
register. The machine seesm to use a frequency of 266 MHz by default,
and fortunately it still boot even with the 50% CPU overclock that
we get when we bump the FSB up to 400 MHz.

It turns out the actual FSB frequency and the register have no real
link whatsoever. The register value is based on some straps or something,
but fortunately those too can be configured from the BIOS on this board,
although it doesn't seem to respect the settings 100%. In the end I was
able to derive the following relationship:

BIOS FSB / strap | CLKCFG
-------------------------
200              | 0x2
266              | 0x0
333              | 0x4
400              | 0x4

So only the 200 and 400 MHz cases actually match how we're currently
decoding that register. But as the comment next to some of the defines
says, we have been just guessing anyway.

So let's fix things up so that at least the 266 MHz case will work
correctly as that is actually the setting used by both the buggy
machine and my test machine.

The fact that 333 and 400 MHz BIOS settings result in the same register
value is a little disappointing, as that means we can't tell them apart.
However, according to the gmch datasheet for both elk and ctg 400 Mhz is
not even a supported FSB frequency, so I'm going to make the assumption
that we should decode it as 333 MHz instead.

Cc: stable@vger.kernel.org
Cc: Tomi Sarvela <tomi.p.sarvela@intel.com>
Reported-by: Tomi Sarvela <tomi.p.sarvela@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100926
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170504181530.6908-1-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Tomi Sarvela <tomi.p.sarvela@intel.com>

drm/i915: Micro-optimise hotpath through intel_ring_begin()

Typically, there is space available within the ring and if not we have
to wait (by definition a slow path). Rearrange the code to reduce the
number of branches and stack size for the hotpath, accomodating a slight
growth for the wait.

v2: Fix the new assert that packets are not larger than the actual ring.
v3: Make the parameters unsigned as well to make usage.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170504130846.4807-3-chris@chris-wilson.co.uk

drm/i915: Report the ring->space from intel_ring_update_space()

Some callers immediately want to know the current ring->space after
calling intel_ring_update_space(), which we can freely provide via the
return parameter.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170504130846.4807-2-chris@chris-wilson.co.uk

drm/i915: Avoid the branch in computing intel_ring_space()

Exploit the power-of-two ring size to compute the space across the
wraparound using a mask rather than a if. Convert to unsigned integers
so the operation is well defined.

References: https://bugs.freedesktop.org/show_bug.cgi?id=99671
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170504130846.4807-1-chris@chris-wilson.co.uk

drm/i915: Use engine->context_pin() to report the intel_ring

Since unifying ringbuffer/execlist submission to use
engine->pin_context, we ensure that the intel_ring is available before
we start constructing the request. We can therefore move the assignment
of the request->ring to the central i915_gem_request_alloc() and not
require it in every engine->request_alloc() callback. Another small step
towards simplification (of the core, but at a cost of handling error
pointers in less important callers of engine->pin_context).

v2: Rearrange a few branches to reduce impact of PTR_ERR() on gcc's code
generation.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170504093308.4137-1-chris@chris-wilson.co.uk

drm/i915: Implement dma_buf_ops->kmap

Since kmap allows us to block we can pin the pages and use our normal
page lookup routine making the implementation simple, or as some might
say quick and dirty.

Testcase: igt/drv_selftest/dmabuf
Testcase: igt/prime_rw
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170503202517.16797-1-chris@chris-wilson.co.uk

Merge tag 'tags/drm-for-v4.12' into drm-intel-next-queued

Backmerge the main drm-next pull to sync up.

Chris also pointed out that

commit ade0b0c965f59176daddbef9c4717354034f9bce
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Sat Apr 22 09:15:37 2017 +0100

    drm/i915: Confirm the request is still active before adding it to the await

is double-applied in the git merge, so make sure we get this right.

Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>

ALSA: x86: Register multiple PCM devices for the LPE audio card

Now that everything is in place let's register a PCM device for
each port of the display engine. This will make it possible to
actually output audio to multiple displays at the same time. And
it avoids modesets on unrelated displays from clobbering up the
ELD and whatnot for the display currently doing the playback.

v2: Add a PCM per port instead of per pipe
v3: Fix off by one error with port numbers (Pierre-Louis)
    Fix .notify_audio_lpe() prototype (Pierre-Louis)

Cc: Takashi Iwai <tiwai@suse.de>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170427160231.13337-12-ville.syrjala@linux.intel.com
Reviewed-by: Takashi Iwai <tiwai@suse.de>

ALSA: x86: Split snd_intelhad into card and PCM specific structures

To allow multiple PCM devices to be registered for the LPE audio card,
split the private data into card and PCM specific chunks. For now we'll
stick to just one PCM device as before.

v2: Rework to do a pcm device per port instead of per pipe

Cc: Takashi Iwai <tiwai@suse.de>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170427160231.13337-11-ville.syrjala@linux.intel.com
Reviewed-by: Takashi Iwai <tiwai@suse.de>

ALSA: x86: Prepare LPE audio ctls for multiple PCMs

In preparation for register a PCM device for each pipe adjust
link up the ctl elements with the corresponding PCM device.

Cc: Takashi Iwai <tiwai@suse.de>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170427160231.13337-10-ville.syrjala@linux.intel.com
Reviewed-by: Takashi Iwai <tiwai@suse.de>

drm/i915: Clean up the LPE audio platform data

Split the LPE audio platform data into a port specific
chunk and device specific chunk. Eventually we'll have
a port specific chunk for each port, but for now we'll
stick to just one.

We'll also get rid of the intel_hdmi_lpe_audio_eld structure
which doesn't seem to have any real reason to exist.

v2: Organize per port instead of per pipe

Cc: Takashi Iwai <tiwai@suse.de>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170427160231.13337-9-ville.syrjala@linux.intel.com
Reviewed-by: Takashi Iwai <tiwai@suse.de>

drm/i915: Reorganize intel_lpe_audio_notify() arguments

Shuffle the arguments to intel_lpe_audio_notify() around a bit. Pipe
and port being the most important things, so let's put the first, and
thre rest can come in as is. Also constify the eld argument.

Cc: Takashi Iwai <tiwai@suse.de>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170427160231.13337-8-ville.syrjala@linux.intel.com
Reviewed-by: Takashi Iwai <tiwai@suse.de>

drm/i915: Remove hdmi_connected from LPE audio pdata

We can determine that the pipe was shut down from pipe<0, so there's
no point in duplicating that information as 'hdmi_connected'.

v2: Use pipe<0 instead of port<0 as we'll want to do per-port
    PCM devices later
    Initialize pipe to -1 to inidicate inactive initial state

Cc: Takashi Iwai <tiwai@suse.de>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170427160231.13337-7-ville.syrjala@linux.intel.com
Reviewed-by: Takashi Iwai <tiwai@suse.de>

drm/i915: Replace tmds_clock_speed and link_rate with just ls_clock

There's no need to distinguish between the DP link rate and HDMI TMDS
clock for the purposes of the LPE audio. Both are actually the same
thing more or less, which is the link symbol clock. So let's just
call the thing ls_clock and simplify the code.

Cc: Takashi Iwai <tiwai@suse.de>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170427160231.13337-6-ville.syrjala@linux.intel.com
Reviewed-by: Takashi Iwai <tiwai@suse.de>

drm/i915: Remove the unused pending_notify from LPE platform data

The pending_notify flag in the LPE audio platform data is pointless,
actually unused. So let's kill it off.

v2: Fix typo in patch subject

Cc: Takashi Iwai <tiwai@suse.de>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170427160231.13337-5-ville.syrjala@linux.intel.com
Reviewed-by: Takashi Iwai <tiwai@suse.de>

drm/i915: Stop pretending to mask/unmask LPE audio interrupts

vlv_display_irq_postinstall() enables the LPE audio interrupts
regardless of whether the LPE audio irq chip has masked/unmasked
them. Also the irqchip masking/unmasking doesn't consider the state
of the display power well or the device, and hence just leads to
dmesg spew when it tries to access the hardware while it's powered
down.

If the current way works, then we don't need to do anything in the
mask/unmask hooks. If it doesn't work, well, then we'd need to properly
track whether the irqchip has masked/unmasked the interrupts when
we enable display interrupts. And the mask/unmask hooks would need
to check whether display interrupts are even enabled before frobbing
with he registers.

So let's just assume the current way works and neuter the mask/unmask
hooks. Also clean up vlv_display_irq_postinstall() a bit and stop
it from trying to unmask/enable the LPE C interrupt on VLV since it
doesn't exist.

Cc: Takashi Iwai <tiwai@suse.de>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170427160231.13337-4-ville.syrjala@linux.intel.com
Reviewed-by: Takashi Iwai <tiwai@suse.de>

ALSA: x86: Clear the pdata.notify_lpe_audio pointer before teardown

Clear the notify function pointer in the platform data before we tear
down the driver. Otherwise i915 would end up calling a stale function
pointer and possibly explode.

Cc: stable@vger.kernel.org
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170427160231.13337-3-ville.syrjala@linux.intel.com
Reviewed-by: Takashi Iwai <tiwai@suse.de>

drm/i915: Fix runtime PM for LPE audio

Not calling pm_runtime_enable() means that runtime PM can't be
enabled at all via sysfs. So we definitely need to call it
from somewhere.

Calling it from the driver seems like a bad idea because it
would have to be paired with a pm_runtime_disable() at driver
unload time, otherwise the core gets upset. Also if there's
no LPE audio driver loaded then we couldn't runtime suspend
i915 either.

So it looks like a better plan is to call it from i915 when
we register the platform device. That seems to match how
pci generally does things. I cargo culted the
pm_runtime_forbid() and pm_runtime_set_active() calls from
pci as well.

The exposed runtime PM API is massive an thorougly misleading, so
I don't actually know if this is how you're supposed to use the API
or not. But it seems to work. I can now runtime suspend i915 again
with or without the LPE audio driver loaded, and reloading the
LPE audio driver also seems to work.

Note that powertop won't auto-tune runtime PM for platform devices,
which is a little annoying. So I'm not sure that leaving runtime
PM in "on" mode by default is the best choice here. But I've left
it like that for now at least.

Also remove the comment about there not being much benefit from
LPE audio runtime PM. Not allowing runtime PM blocks i915 runtime
PM, which will also block s0ix, and that could have a measurable
impact on power consumption.

Cc: stable@vger.kernel.org
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Fixes: 0b6b524f3915 ("ALSA: x86: Don't enable runtime PM as default")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170427160231.13337-2-ville.syrjala@linux.intel.com
Reviewed-by: Takashi Iwai <tiwai@suse.de>

drm/i915: Switch the global i915.semaphores check to a local predicate

Rather than use a global modparam, we can just check to see if the
engine has semaphores configured upon it.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170503093924.5320-7-chris@chris-wilson.co.uk

drm/i915: Do not record a successful syncpoint for a dma-await

As we may unwind the requests, even though the request we are awaiting
has a global_seqno that seqno may be revoked during the await and so we
can not reliably use it as a barrier for all future awaits on the same
timeline.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170503093924.5320-6-chris@chris-wilson.co.uk

drm/i915: Rename intel_timeline.sync_seqno[] to .global_sync[]

With the addition of the inter-context intel_time.sync map, having a
very similar sync_seqno[] is confusing. Aide the reader by denoting that
this is a pre-allocated array for storing semaphore sync points wrt to
the global seqno.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170503093924.5320-5-chris@chris-wilson.co.uk

drm/i915: Squash repeated awaits on the same fence

Track the latest fence waited upon on each context, and only add a new
asynchronous wait if the new fence is more recent than the recorded
fence for that context. This requires us to filter out unordered
timelines, which are noted by DMA_FENCE_NO_CONTEXT. However, in the
absence of a universal identifier, we have to use our own
i915->mm.unordered_timeline token.

v2: Throw around the debug crutches
v3: Inline the likely case of the pre-allocation cache being full.
v4: Drop the pre-allocation support, we can lose the most recent fence
in case of allocation failure -- it just means we may emit more awaits
than strictly necessary but will not break.
v5: Trim allocation size for leaf nodes, they only need an array of u32
not pointers.
v6: Create mock_timeline to tidy selftest writing
v7: s/intel_timeline_sync_get/intel_timeline_sync_is_later/ (Tvrtko)
v8: Prune the stale sync points when we idle.
v9: Include a small benchmark in the kselftests
v10: Separate the idr implementation into its own compartment. (Tvrkto)
v11: Refactor igt_sync kselftests to avoid deep nesting (Tvrkto)
v12: __sync_leaf_idx() to assert that p->height is 0 when checking leaves
v13: kselftests to investigate struct i915_syncmap itself (Tvrtko)
v14: Foray into ascii art graphs
v15: Take into account that the random lookup/insert does 2 prng calls,
not 1, when benchmarking, and use for_each_set_bit() (Tvrtko)
v16: Improved ascii art

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170503093924.5320-4-chris@chris-wilson.co.uk

drm/i915: Lift timeline ordering to await_dma_fence

Currently we filter out repeated use of the same timeline in the low
level i915_gem_request_await_request(), after having added the
dependency on the old request. However, we can lift this to
i915_gem_request_await_dma_fence() (before the dependency is added)
using the observation that requests along the same timeline are
explicitly ordered via i915_add_request (along with the dependencies).

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170503093924.5320-3-chris@chris-wilson.co.uk

drm/i915: Unwrap top level fence-array

By first unwrapping an incoming fence-array into its child fences, we
can simplify the internal branching, and so avoid triggering a potential
bug in the next patch when not squashing the child fences on the same
timeline.

It will also have the advantage of keeping the (top-level) fence arrays
out of any fence/timeline caching since these are unordered timelines
but with a random context id.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170503093924.5320-2-chris@chris-wilson.co.uk

drm/i915: Mark up clflushes as belonging to an unordered timeline

2 clflushes on two different objects are not ordered, and so do not
belong to the same timeline (context). Either we use a unique context
for each, or we reserve a special global context to mean unordered.
Ideally, we would reserve 0 to mean unordered (DMA_FENCE_NO_CONTEXT) to
have the same semantics everywhere.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170503093924.5320-1-chris@chris-wilson.co.uk

drm/i915: Use wait_for_atomic_us when waiting for gt fifo

Replace the handcrafter loop when checking for fifo slots
with atomic wait for. This brings this wait in line with
the other waits on register access. We also get a readable
timeout constraint, so make it to fail after 10ms.

Chris suggested that we should fail silently as the fifo debug
handler, now attached to unclaimed mmio handling, will take care of the
possible errors at later stage.

Note that the decision to wait was changed so that we avoid
allocating the first reserved entry. Nor do we reduce the count
if we fail the wait, removing the possiblity to wrap the
count if the hw fifo returned zero.

v2: remove unclaimed check on timeout (Chris)
v3: use void return (Chris)

References: https://bugs.freedesktop.org/show_bug.cgi?id=100247
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1491493182-31540-1-git-send-email-mika.kuoppala@intel.com

drm/i915: Move the GTFIFODBG to the common mmio dbg framework

Remove the per-mmio checking of the FIFO debug register into the common
conditional mmio debug handling. Based on patch from Chris Wilson.

v2: postpone warn on fifodbg for unclaimed reg debugs

Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915/guc: Enable send function only after successful init

It is safer to setup valid send function after successful GuC
hardware initialization. In addition we prepare placeholder
where we can setup any alternate GuC communication mechanism.

Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170502103243.54940-1-michal.wajdeczko@intel.com
[ickle: Fixup ENODEV for an impossible error path]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915: Do not leak dev_priv->l3_parity.remap_info[]

Add intel_irq_fini() for placing the deinitialization code,
starting with freeing dev_priv->l3_parity.remap_info[].

Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1493366319-18515-1-git-send-email-joonas.lahtinen@linux.intel.com

drm/i915: Update DRIVER_DATE to 20170502

Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Merge branch 'linux-4.12' of git://github.com/skeggsb/linux into drm-next

Some nouveau regression fixes.

* 'linux-4.12' of git://github.com/skeggsb/linux:
  drm/nouveau/fb/gf100-: Fix 32 bit wraparound in new ram detection
  drm/nouveau/secboot/gm20b: fix the error return code in gm20b_secboot_tegra_read_wpr()
  drm/nouveau/kms: Increase max retries in scanout position queries.
  drm/nouveau/bios/bitP: check that table is long enough for optional pointers
  drm/nouveau/fifo/nv40: no ctxsw for pre-nv44 mpeg engine

drm/nouveau/fb/gf100-: Fix 32 bit wraparound in new ram detection

A missing u64 cast causes a 32-Bit wraparound from
4096 MiB to 0 MiB and therefore total 0 MiB VRAM detected
if card has 4096 Mib per FBP.

Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Reviewed-by: Karol Herbst <karolherbst@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

drm/nouveau/secboot/gm20b: fix the error return code in gm20b_secboot_tegra_read_wpr()

The error return code PTR_ERR(mc) is always 0 since mc is
equal to 0 in this error handling case.

Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

drm/nouveau/kms: Increase max retries in scanout position queries.

So far we only allowed for 1 retry and just failed the query
- and thereby high precision vblank timestamping - if we did
not get a reasonable result, as such a failure wasn't considered
all too horrible. There are a few NVidia gpu models out there which
may need a bit more than 1 retry to get a successful query result
under some conditions.

Since Linux 4.4 the update code for vblank counter and timestamp
in drm_update_vblank_count() changed so that the implementation
assumes that high precision vblank timestamping of a kms driver
either consistently succeeds or consistently fails for a given
video mode and encoder/connector combo. Iow. switching from success
to fail or vice versa on a modeset or connector change is ok, but
spurious temporary failure for a given setup can confuse the core
code and potentially cause bad miscounting of vblanks and confusion
or hangs in userspace clients which rely on vblank  stuff, e.g.,
desktop compositors.

Therefore change the max retry count to a larger number - more than
any gpu so far is known to need to succeed, but still low enough
so that these queries which do also happen in vblank interrupt are
still fast enough to be not disastrously long if something would
go badly wrong with them.

As such sporadic retries only happen seldom even on affected gpu's,
this could mean a vblank irq could take a few dozen microseconds
longer every few hours of uptime -- better than a desktop compositor
randomly hanging every couple of hours or days of uptime in a hard
to reproduce manner.

Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

drm/nouveau/bios/bitP: check that table is long enough for optional pointers

Fixes OOB VBIOS accesses on some boards.

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>