Hauke Mehrtens [Fri, 11 Sep 2015 17:58:39 +0000 (17:58 +0000)]
binutils: add binutils 2.25.1
This adds binutils 2.25.1 as an option to OpenWrt.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46874
Hauke Mehrtens [Fri, 11 Sep 2015 17:57:39 +0000 (17:57 +0000)]
gcc: update gcc 5.x musl patches
This replaces the musl patches for gcc with the versions which are in
gcc trunk.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46873
Hauke Mehrtens [Fri, 11 Sep 2015 17:55:28 +0000 (17:55 +0000)]
brcm47xx: increase max image size
the trx utile uses a maximum image size of 7.2MB. There are brcm47xx
devices even with serial flash with bigger flash chips, but OpenWrt was
not able to create images for these devices. This patch provides an
additional parameter which increases this limit to 32 MB. There is a
warning in the trx utile code which suggests that bigger images could
overwrite the nvram partition on some devices, but normally the program
writing the image should make sure that it is safe to write it to the
flash.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46872
Hauke Mehrtens [Fri, 11 Sep 2015 17:54:55 +0000 (17:54 +0000)]
brcm47xx: break long lines in image Makefile
This patch changes nothing on the behaviour, it just breaks long lines
with bin/trx to make it easier to add additional parameters.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46871
Felix Fietkau [Fri, 11 Sep 2015 17:17:30 +0000 (17:17 +0000)]
brcm2708: remove linux 3.18 support
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46870
Felix Fietkau [Fri, 11 Sep 2015 16:35:46 +0000 (16:35 +0000)]
lantiq: Use the BAR0 base address in the ath PCI fixup code
Fixes support for AR9287 on TP-Link TD-W8980 and possibly other devices
which have an ath wifi chip at a PCI address other than 0xb8000000
(TD-W8980 for example has it's wifi chip at 0xbc000000).
Signed-off-by: Geoffrey McRae <geoff@spacevs.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46869
Felix Fietkau [Fri, 11 Sep 2015 16:35:32 +0000 (16:35 +0000)]
ugps: fix filename to eliminate build problems
due to ordering PKG_SOURCE_VERSION is not defined leading
to a filename "ugps-.tar.bz2"
This errors out when an older version is in the dl/ dir (or LOCALMIRROR)
fix order and use uhttpd file naming scheme to visibly include date
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 46868
Felix Fietkau [Fri, 11 Sep 2015 16:35:17 +0000 (16:35 +0000)]
base-files: set kernel.core_pattern in sysctl.conf
Move the pattern setting from netifd's service script to
/etc/sysctl.conf. Put the timestamp component '%t' just after
executable name '%e' for more natural order from output of ls command.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 46867
Felix Fietkau [Fri, 11 Sep 2015 16:35:02 +0000 (16:35 +0000)]
util-linux: add prlimit command.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 46866
Felix Fietkau [Fri, 11 Sep 2015 16:34:49 +0000 (16:34 +0000)]
mvsw61xx: match swconfig function names
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 46865
Felix Fietkau [Fri, 11 Sep 2015 16:34:35 +0000 (16:34 +0000)]
mvsw61xx: use standard swconfig get_port_link
The previous "link" and "status" functions were non-standard,
and thus less useful for parsing.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 46864
Felix Fietkau [Fri, 11 Sep 2015 16:34:22 +0000 (16:34 +0000)]
ipkg-build: add ogargs to outer tar/ipk
prevent name:uid leaks of build system
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 46863
Felix Fietkau [Fri, 11 Sep 2015 16:34:08 +0000 (16:34 +0000)]
ar71xx: Restore buildability of the AP121 target
Increase space for kernel and also introduce a 8M flash target into the
Makefile.
Signed-off-by: Attila Lendvai <attila@lendvai.name>
SVN-Revision: 46862
Felix Fietkau [Fri, 11 Sep 2015 16:33:54 +0000 (16:33 +0000)]
hostapd: Add eapol_version config option
Add eapol_version to the openwrt wireless config ssid section.
Only eapol_version=1 and 2 will get passed to hostapd, the default
in hostapd is 2.
This is only useful for really old client devices that don't
accept eapol_version=2.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
SVN-Revision: 46861
Felix Fietkau [Fri, 11 Sep 2015 16:33:39 +0000 (16:33 +0000)]
openvpn: remove __DATE__ from options output
reported by:
https://reproducible.debian.net/openwrt/dbd/ar71xx/base/openvpn-nossl_2.3.7-1_ar71xx.ipk.html
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 46860
Felix Fietkau [Fri, 11 Sep 2015 16:33:26 +0000 (16:33 +0000)]
include/image.mk: make tar reproducible
several packages reported different file order between builds
make binutils, kmod-sched reproducible
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 46859
Felix Fietkau [Fri, 11 Sep 2015 16:33:12 +0000 (16:33 +0000)]
yaffs2: remove __TIME__ __DATE__ macros
prevent compiler errors with gcc 4.9
increase reproducibility
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 46858
Felix Fietkau [Fri, 11 Sep 2015 16:32:58 +0000 (16:32 +0000)]
ramips: Enable RTC support for PBR-M1
The PBR-M1 and other upcoming MT7621 boards have RTC chips on them. The
PBR-M1 also selects the kmod-rtc-pcf8563 by default. But the module itself
will not be build because CONFIG_RTC_CLASS is currently not enabled for its
kernel.
Enabling this option should fix the problem of the missing rtc device on
these boards.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 46857
Felix Fietkau [Fri, 11 Sep 2015 16:32:45 +0000 (16:32 +0000)]
ar71xx: fix ar724x clock calculation
According to the AR7242 datasheet section 2.8, AR724X CPUs use a 40MHz
input clock as the REF_CLK instead of 5MHz.
The correct CPU PLL calculation procedure is as follows:
CPU_PLL = (DIV * REF_CLK) / REF_DIV / 2.
This patch is compatible with the current calculation procedure with default
DIV and REF_DIV values.
Test on both AR7240, AR7241 and AR7242.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
SVN-Revision: 46856
Felix Fietkau [Fri, 11 Sep 2015 16:32:28 +0000 (16:32 +0000)]
brcm2708-gpu-fw: update to latest version
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 46855
Felix Fietkau [Fri, 11 Sep 2015 16:32:15 +0000 (16:32 +0000)]
brcm2708: add kmod-sound-soc-raspidac3
This adds support for RaspiDAC Rev.3x
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 46854
Felix Fietkau [Fri, 11 Sep 2015 16:32:00 +0000 (16:32 +0000)]
brcm2708: update 4.1 patches
As usual, this patches were taken (and rebased) from
https://github.com/raspberrypi/linux/commits/rpi-4.1.y
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 46853
Felix Fietkau [Fri, 11 Sep 2015 16:31:35 +0000 (16:31 +0000)]
target: ar71xx: add support for COMFAST CF-E316N v2 board
This adds full support (sans sysupgrading from vendor firmware) for the COMFAST
CF-E316N v2 (aka CF-E316V2, CF-E316N-V2 and CF-E316Nv2.0, no FCC ID) by
Shenzhen Four Seas Global Link Network Technology Co., Ltd (this company is
actively refusing to provide GPL'd sources for the OpenWrt version they ship
with the device, damn them).
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
SVN-Revision: 46852
Felix Fietkau [Fri, 11 Sep 2015 16:31:18 +0000 (16:31 +0000)]
hostapd: work around unconditional libopenssl build dependency
As the OpenWrt build system only resolves build dependencies per directory,
all hostapd variants were causing libopenssl to be downloaded and built,
not only wpad-mesh. Fix this by applying the same workaround as in
ustream-ssl.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 46851
Felix Fietkau [Fri, 11 Sep 2015 16:31:01 +0000 (16:31 +0000)]
opkg: work around unconditional libopenssl build dependency
As the OpenWrt build system only resolves build dependencies per directory,
all opkg variants were causing libopenssl to be downloaded and built,
not only opkg-smime. Fix this by applying the same workaround as in
ustream-ssl.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 46850
Rafał Miłecki [Fri, 11 Sep 2015 08:56:37 +0000 (08:56 +0000)]
base-files: change banner to Designated Driver release
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46846
Steven Barth [Fri, 11 Sep 2015 06:46:42 +0000 (06:46 +0000)]
comgt-ncm: Add possibility to choose PDP context type
By setting the option pdptype to IP, IPV6 or IPV4V6 the user can
choose the context type between IPv4, IPv6 and dual stack,
respectively. The default setting is dual stack, except if option
ipv6=0 is specified, in which case IPv4 context is the default.
This allows for an out-of-the-box IPv6 support with modems
utilizing NCM-like protocols.
While we are at it, also add commands for Sierra DirectIP modems
(currently untested), which will allow us to drop the separate
comgt-directip package (once tested and verified working).
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 46844
Steven Barth [Fri, 11 Sep 2015 06:46:40 +0000 (06:46 +0000)]
uqmi: Add proper IPv6 support
Use the new --ip-family option to start both IPv4 and IPv6 sessions
by default. Autoconnect can't be used when starting two sessions,
so revert back to using the client IDs and packet data handles for
handling the network connection.
Some modem firmwares do not implement a RA server, therefore by
default use outband IP configuration and static addressing. Some
other firmwares report bogus IP configuration with the WDS get
current settings command. In this case inband configuration with
DHCP/RA can be optionally enabled by setting option dhcp to 1.
Per 3GPP standard a /64 prefix is served to all clients, which is
extended to LAN as specified in RFC 7278.
v2: Restrict the IPv6 gateway route source address
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 46843
Steven Barth [Fri, 11 Sep 2015 06:46:35 +0000 (06:46 +0000)]
firewall: Remove src_port from firewall.config to receive dhcpv6 replies
Seems like my second try was again whitespace broken. Sorry for the noise.
Remove src_port from firewall.config to receive dhcpv6 replies. Fixes #20295.
Signed-off-by: Anselm Eberhardt <a.eberhardt@cygnusnetworks.de>
SVN-Revision: 46842
Felix Fietkau [Thu, 10 Sep 2015 21:00:19 +0000 (21:00 +0000)]
netifd: update to the latest version, fixes a WDS STA mode regression caused by multicast-to-unicast handling (#20466)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46841
Felix Fietkau [Thu, 10 Sep 2015 11:06:42 +0000 (11:06 +0000)]
imagebuilder: run build prereq checks before building image to set up host commands properly
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46840
Jonas Gorski [Thu, 10 Sep 2015 10:09:42 +0000 (10:09 +0000)]
ipq806x: fix uninitialized variable usage in cpufreq-krait
In krait_cpufreq_probe, both freq and max_cpu_freq are never
initialized, so the max_cpu_freq will have a random value at the end.
Fix this by properly initializing max_cpu_freq to 0 and storing the clk
frequency in freq as well, to make it similar to how it's calculated in
krait_set_target.
Fixes the following warnings:
In file included from include/linux/clk.h:16:0,
from drivers/cpufreq/cpufreq-krait.c:13:
drivers/cpufreq/cpufreq-krait.c: In function 'krait_cpufreq_probe':
include/linux/kernel.h:714:24: warning: 'freq' may be used uninitialized in this function [-Wmaybe-uninitialized]
_max1 > _max2 ? _max1 : _max2; })
^
drivers/cpufreq/cpufreq-krait.c:217:25: note: 'freq' was declared here
unsigned long freq_Hz, freq, max_cpu_freq;
^
In file included from include/linux/clk.h:16:0,
from drivers/cpufreq/cpufreq-krait.c:13:
include/linux/kernel.h:714:24: warning: 'max_cpu_freq' may be used uninitialized in this function [-Wmaybe-uninitialized]
_max1 > _max2 ? _max1 : _max2; })
^
drivers/cpufreq/cpufreq-krait.c:217:31: note: 'max_cpu_freq' was declared here
unsigned long freq_Hz, freq, max_cpu_freq;
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46839
Jonas Gorski [Thu, 10 Sep 2015 10:09:36 +0000 (10:09 +0000)]
ipq806x: modules: fix typo in usb-dwc3-qcom dependencies
The phy driver has its qcom-dwc3 order switched in contrast to the usb
controller driver.
Signed-off-by: Kaspar Schleiser <kaspar@schleiser.de>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46838
Jonas Gorski [Thu, 10 Sep 2015 10:09:26 +0000 (10:09 +0000)]
ipq806x: fix R7500 kernel generation
Obviously the dummy rootfs must be after the kernel (uImage), not
included in it.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46837
Felix Fietkau [Wed, 9 Sep 2015 20:36:10 +0000 (20:36 +0000)]
busybox: lock: implement -n "Fail rather than wait"
lock -n is similiar to flock -n. If the lock was already taken,
fail with exit code = 1 and write error message to stderr.
example:
if ! lock -n /tmp/foo ; then
echo lock exits.
else
echo lock was free. But is locked now.
fi
> lock was free. But is locked now.
> lock exists.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 46836
Felix Fietkau [Wed, 9 Sep 2015 18:40:15 +0000 (18:40 +0000)]
generic: Fix per interface nf_call_iptables setting
commit r30917 ("kernel: bypass all netfilter hooks if the sysctls for that
functionality have been disabled - eliminates the overhead of enabling
CONFIG_BRIDGE_NETFILTER in the kernel config") introduced an optimization
which should reduce/eliminate the overhead for traffic send over bridges on
kernels compiled with CONFIG_BRIDGE_NETFILTER=y. But this optimization
breaks the nf_call_iptables per bridge setting which is more fine grained
than the global sysctl net.bridge.bridge-nf-call-iptables setting.
A test reflecting a real world setup was created to identify if this really
eliminates the overhead and if per-bridge nf_call_iptables could be used in
some setups to increase the throughput. A Qualcomm Atheros QCA9558 based
system with one ethernet and an ath9k wifi 3x3 in HT40 mode was used.
Cables from the AP to the wifi station were used to reduce interference
problems during the tests.
The wlan interface was put in one bridge interface called br-wlan. This
bridge usually contains some more wlan interfaces. The eth0 was put in a
second bridge called br-lan. This usually contains some other privileged
wlan or mesh interfaces. Routing was added between br-lan and br-wlan.
Three kernels were tested:
* (default) OpenWrt kernel for this device
* (brfilter-global) OpenWrt kernel with CONFIG_BRIDGE_NETFILTER=y
* (brfilter-local) OpenWrt kernel with CONFIG_BRIDGE_NETFILTER=y and
without 644-bridge_optimize_netfilter_hooks.patch
The changes to the the netfilter settings of the bridge were done via:
* (brfilter-global) /sbin/sysctl -w net.bridge.bridge-nf-call-iptables=1
* (brfilter-lobal) echo 1 > /sys/class/net/br-lan/bridge/nf_call_iptables
and/or echo 1 > /sys/class/net/br-wan/bridge/nf_call_iptables
A station connected to the wlan0 (AP) interface was used to send traffic to
a PC connected via ethernet. iperf with 3 concurrent transmissions was used
to generate the traffic.
| kernel | br-nf-* global | nf-call* iface | download | upload |
|-----------------|----------------|----------------|----------|----------|
| default | 0 | - | 209 | 268 |
| brfilter-global | 0 | - | 185 | 243 |
| brfilter-local | 0 | - | 187 | 243 |
| brfilter-local | 0 | br-lan | 157 | 226 |
| brfilter-local | 0 | br-lan br-wlan | 139 | 161 |
| brfilter-global | 1 | - | 136 | 162 |
Download/upload results in Mibit/s
It can be seen that the patch doesn't eliminate the overhead. It can also
be seen that the throughput of brfilter-global and brfilter-local with
disabled filtering is the roughly the same. Also the throughput for
brfilter-global and brfilter-local for enabled filtering on all bridges is
roughly the same.
But also the brfilter-local throughput is higher when only br-lan requires
the filtering. This setting would not be possible with
644-bridge_optimize_netfilter_hooks.patch applied and thus can only be
compared with brfilter-global and filtering enabled for all interfaces.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 46835
Steven Barth [Wed, 9 Sep 2015 12:20:36 +0000 (12:20 +0000)]
linux: make IPv6 builtin if selected (saves >30KB)
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 46834
Steven Barth [Wed, 9 Sep 2015 10:38:16 +0000 (10:38 +0000)]
busybox: fix ip applet and netlink behavior
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 46833
Steven Barth [Tue, 8 Sep 2015 17:44:24 +0000 (17:44 +0000)]
package: replace ifconfig-usage with ip
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 46832
Steven Barth [Tue, 8 Sep 2015 17:44:17 +0000 (17:44 +0000)]
iproute2: improve ip-full coexistence, remove rt_table
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 46831
Steven Barth [Tue, 8 Sep 2015 17:44:13 +0000 (17:44 +0000)]
base-files: add /etc/iproute2/rt_tables, replace ifconfig-usage
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 46830
Steven Barth [Tue, 8 Sep 2015 17:44:10 +0000 (17:44 +0000)]
busybox: improve applets & deprecate ifconfig, route
added: ip addr, ip route, ip link, traceroute6
removed: hostid, devmem, vconfig, arping
deprecated (to be removed): ifconfig, route
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 46829
Rafał Miłecki [Tue, 8 Sep 2015 16:43:32 +0000 (16:43 +0000)]
kernel: describe bridge patch "multicast to unicast"
It was initially added in r41367 by nbd.
SVN-Revision: 46828
Rafał Miłecki [Tue, 8 Sep 2015 16:43:21 +0000 (16:43 +0000)]
kernel: describe bridge patch "optimize netfilter hooks"
It was initially added in r30917 by nbd.
SVN-Revision: 46827
Rafał Miłecki [Tue, 8 Sep 2015 16:43:10 +0000 (16:43 +0000)]
kernel: describe bridge patch "remove IPv6 depependency of bridge in 2.6.38+"
It was initially added in r27237 by jow as patch from Jonas.
SVN-Revision: 46826
Rafał Miłecki [Tue, 8 Sep 2015 16:43:04 +0000 (16:43 +0000)]
kernel: describe bridge patch "port isolate"
It was initially added in r25762 by nbd.
SVN-Revision: 46825
Rafał Miłecki [Tue, 8 Sep 2015 16:42:58 +0000 (16:42 +0000)]
kernel: describe bridge patch "always accept EAP"
It was initially added in r26015 by nbd.
SVN-Revision: 46824
Rafał Miłecki [Tue, 8 Sep 2015 16:42:50 +0000 (16:42 +0000)]
kernel: describe bridge patch "no EAP forward"
It was initially added in r25095 by nbd.
SVN-Revision: 46823
Felix Fietkau [Tue, 8 Sep 2015 14:29:55 +0000 (14:29 +0000)]
kernel: restore 640-bridge_no_eap_forward.patch to its original form
It was corrupted in r38528. The most obvious symptom is repeated messages like this:
Tue Sep 8 08:25:18 2015 kern.warn kernel: [77141.972226] br-lan: received packet on wlan0 with own address as source address
Signed-off-by: Dmitry Ivanov <dima@ubnt.com>
SVN-Revision: 46821
Felix Fietkau [Tue, 8 Sep 2015 12:31:04 +0000 (12:31 +0000)]
kernel: remove packaging of kmod-crypto-core and kmod-crypto-arc4
Everything except for blkcipher was already built-in, so make blkcipher
built-in as well.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46820
Steven Barth [Tue, 8 Sep 2015 12:13:29 +0000 (12:13 +0000)]
map: be less restrictive when matching lw4over6 prefixes
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 46819
Felix Fietkau [Tue, 8 Sep 2015 11:48:48 +0000 (11:48 +0000)]
iw: reduce size even more (~12k after gzip)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46818
Felix Fietkau [Tue, 8 Sep 2015 10:57:11 +0000 (10:57 +0000)]
musl: add a hack to remove unused crypt() algorithms, saves ~14k after lzma
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46816
Steven Barth [Tue, 8 Sep 2015 08:59:40 +0000 (08:59 +0000)]
dropbear: remove generation and configuration of DSS keys
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 46815
Felix Fietkau [Tue, 8 Sep 2015 08:55:10 +0000 (08:55 +0000)]
dropbear: disable 3des, cbc mode, dss support, saves about 5k gzipped
While technically required by the RFC, they are usually completely
unused (DSA), or have security issues (3DES, CBC)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46814
Felix Fietkau [Tue, 8 Sep 2015 07:10:07 +0000 (07:10 +0000)]
argp-standalone: fix build error with gcc 5.2 (#20460)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46813
Rafał Miłecki [Tue, 8 Sep 2015 05:24:57 +0000 (05:24 +0000)]
brcm47xx: apply serial flash size trick to Netgear WNR1000 V3
It also uses different block size just like WGR614 V10.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46810
Steven Barth [Mon, 7 Sep 2015 19:29:25 +0000 (19:29 +0000)]
Disable telnet in favor of passwordless SSH
This enables passworldless login for root via SSH whenever no root
password is set (e.g. after reset, flashing without keeping config
or in failsafe) and removes telnet support alltogether.
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 46809
Felix Fietkau [Mon, 7 Sep 2015 19:18:58 +0000 (19:18 +0000)]
uhttpd: update to the latest version, fixes deferred cgi script processing (#20458)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46807
Rafał Miłecki [Mon, 7 Sep 2015 16:43:29 +0000 (16:43 +0000)]
brcm47xx: fix reading WGT634U CFE variables with 4.1
This ports fix from r46584 to the 4.1.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46806
Rafał Miłecki [Mon, 7 Sep 2015 16:29:21 +0000 (16:29 +0000)]
brcm47xx: add Netgear WNR1000 V3 support in the Linux arch code
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46805
Steven Barth [Mon, 7 Sep 2015 16:21:15 +0000 (16:21 +0000)]
map: ignore insignificant PSID bits
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 46804
Steven Barth [Mon, 7 Sep 2015 13:31:36 +0000 (13:31 +0000)]
odhcpd: fix parsing of host entries without duid
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 46803
Steven Barth [Mon, 7 Sep 2015 09:49:35 +0000 (09:49 +0000)]
odhcpd: various bugfixes
* ra: don't announce as default router if we aren't (regression)
* ra: reduce maximum announced dns lifetimes due to buggy clients
* dhcpv6: fix mac-based lease-matching
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 46802
Steven Barth [Mon, 7 Sep 2015 08:03:34 +0000 (08:03 +0000)]
nls.mk: add -rpath-link when needed for NLS support
When a package links to a shared library that depends on libiconv or
libintl shared libraries, specifying directory pathes to them via -L
switches is not enough, see "man 1 ld" -rpath-link description.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
SVN-Revision: 46801
Felix Fietkau [Mon, 7 Sep 2015 06:59:56 +0000 (06:59 +0000)]
gcc: add missing powerpc patch for 5.2.0
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46800
Felix Fietkau [Sun, 6 Sep 2015 10:07:07 +0000 (10:07 +0000)]
gcc: remove 4.6.3 leftovers
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46799
Felix Fietkau [Sun, 6 Sep 2015 10:07:03 +0000 (10:07 +0000)]
gcc: remove version 4.9-linaro
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46798
Felix Fietkau [Sun, 6 Sep 2015 09:57:02 +0000 (09:57 +0000)]
uboot-ar71xx: fix gcc 5.2 compile errors
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46797
Jonas Gorski [Fri, 4 Sep 2015 14:46:06 +0000 (14:46 +0000)]
ipq806x: add support for Netgear Nighthawk X4 R7500
Add support for the Netgear Nighthawk X4 R7500 and build
appropariate sysupgrade and factory images.
Known issues:
* 5 GHz wifi not working - there is no quantenna driver
* One of the USB ports is not working
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46796
Jonas Gorski [Fri, 4 Sep 2015 14:45:49 +0000 (14:45 +0000)]
ipq806x: enable ide led trigger
To use gpio leds as ide leds, we need to enable the trigger to be
included in the kernel.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46795
Jonas Gorski [Fri, 4 Sep 2015 14:45:45 +0000 (14:45 +0000)]
base-files: allow setting ide-disk led trigger
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46794
Jonas Gorski [Fri, 4 Sep 2015 14:45:40 +0000 (14:45 +0000)]
ipq806x: add support for retrieving macs from mtd
Add support for mtd-mac-address for stmac.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46793
Jonas Gorski [Fri, 4 Sep 2015 14:45:16 +0000 (14:45 +0000)]
image: allow exactly KERNEL_SIZE sized kernels
The KERNEL_SIZE should be the maximum size, inclusive, so we need to
check for greater equal, not just greater.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46792
Jonas Gorski [Fri, 4 Sep 2015 14:45:09 +0000 (14:45 +0000)]
image: move netgear-image to top and rename to -dni
Use the same naming as netgear-chk.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46791
Jonas Gorski [Fri, 4 Sep 2015 14:45:04 +0000 (14:45 +0000)]
ar71xx: rename NETGEAR_ variables to their netgear names
Netgear names them BOARD_ID and HW_ID, so we should do the same.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46790
Jonas Gorski [Fri, 4 Sep 2015 14:45:00 +0000 (14:45 +0000)]
ipq806x: build images and add sysupgrade support for AP148
Add full ubi and sysupgrade images for AP148 and add sysupgrade support
for ipq806x to allow updating the current installation.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46789
Jonas Gorski [Fri, 4 Sep 2015 14:44:51 +0000 (14:44 +0000)]
ipq806x: clear IMAGES for devices
Ensure that IMAGE-less devices won't keep the IMAGES of any previous
devices.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46788
Jonas Gorski [Fri, 4 Sep 2015 14:44:48 +0000 (14:44 +0000)]
ipq806x: wrap legacy image in uImage
Wrap the zImage in a uImage header so we can easily boot it from legacy
u-boots.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46787
Jonas Gorski [Fri, 4 Sep 2015 14:44:44 +0000 (14:44 +0000)]
ipq806x: rename "rootfs" to "ubi" on nand
OpenWrt expects the ubi paritition to be named "ubi", not "rootfs".
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46786
Jonas Gorski [Fri, 4 Sep 2015 14:44:36 +0000 (14:44 +0000)]
ipq806x: enable smem-parser for nand on AP148
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46785
Jonas Gorski [Fri, 4 Sep 2015 14:44:27 +0000 (14:44 +0000)]
build: add a build step for generic sysupgrade nand image
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46784
Jonas Gorski [Fri, 4 Sep 2015 14:44:10 +0000 (14:44 +0000)]
image: add a build step for building and appending an ubinized rootfs
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46783
Jonas Gorski [Fri, 4 Sep 2015 14:44:04 +0000 (14:44 +0000)]
ipq806x: enable ubiblock support
To allow squashfs on ubi, enable ubiblock support in the kernel.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46782
Steven Barth [Fri, 4 Sep 2015 06:29:36 +0000 (06:29 +0000)]
odhcp6c: correctly extend prefix from RAs
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 46781
Steven Barth [Thu, 3 Sep 2015 15:53:40 +0000 (15:53 +0000)]
comgt/umbim/uqmi: enable RFC 7278 for 3g/4g by default
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 46780
Steven Barth [Thu, 3 Sep 2015 15:53:33 +0000 (15:53 +0000)]
odhcp6c: add RFC 7278 3gpp IPv6 prefix extension
Use option extendprefix 1 to enable
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 46779
Felix Fietkau [Thu, 3 Sep 2015 13:15:19 +0000 (13:15 +0000)]
mdns: update to the latest version, fixes a spurious build error
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46778
Felix Fietkau [Thu, 3 Sep 2015 13:15:05 +0000 (13:15 +0000)]
uclibc++: fix build with gcc 5.2
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46777
Felix Fietkau [Thu, 3 Sep 2015 13:14:56 +0000 (13:14 +0000)]
libpcap: update to version 1.7.4
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46776
Felix Fietkau [Thu, 3 Sep 2015 13:14:50 +0000 (13:14 +0000)]
gdb: update to the latest version, fixes a build error with gcc 5.2
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46775
Felix Fietkau [Thu, 3 Sep 2015 13:14:44 +0000 (13:14 +0000)]
gcc: add ARM codegen fix from PR 65932
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46774
Felix Fietkau [Wed, 2 Sep 2015 16:22:44 +0000 (16:22 +0000)]
ar7: fix HIGHMEM_START (#20427)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46773
Felix Fietkau [Wed, 2 Sep 2015 15:44:17 +0000 (15:44 +0000)]
musl: update to version 1.1.11
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46772
Jo-Philipp Wich [Wed, 2 Sep 2015 11:54:03 +0000 (11:54 +0000)]
base-files: add /etc/hosts entries for ::1, ff02::1 and ff02::2
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 46771
Steven Barth [Wed, 2 Sep 2015 11:49:00 +0000 (11:49 +0000)]
dnsmasq: make /tmp/dnsmasq.d and /tmp/hosts preferred over UCI settings
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 46770
Steven Barth [Wed, 2 Sep 2015 11:48:57 +0000 (11:48 +0000)]
dropbear: bump to 2015.68
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 46769
Jonas Gorski [Wed, 2 Sep 2015 10:18:15 +0000 (10:18 +0000)]
kernel: update 3.18 to 3.18.21
Changelog:
* https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.21
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46768
Felix Fietkau [Wed, 2 Sep 2015 09:24:05 +0000 (09:24 +0000)]
ramips: fix devicetree corruption with some boot loaders if the caches are not ready at boot
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 46766
Felix Fietkau [Wed, 2 Sep 2015 09:23:59 +0000 (09:23 +0000)]
kernel: bridge, multicast-to-unicast: fix echoes on STA
Currently, multicast packets from an STA are sent to any according
multicast listener directly through the bridge multicast-to-unicast
feature. Unfortunately, so far this includes the originating STA, too,
resulting in multicast packets being echo'ed back to the originating STA
if it itself is a multicast listener for that group.
This behaviour breaks IPv6 duplicate address detection: An IPv6 Neighbor
Solicitation for IPv6 Duplicate Address Detection is being echo'ed back,
resulting in the host falsely detecting an address collision, which
makes the node unable to claim an IPv6 address and use IPv6 in general.
Mac80211 unfortunately only prevents the echoes for us for multicast
frames. For the multicast frames cast to a unicast destination we'll
need to take care of excluding the originator ourselves.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
SVN-Revision: 46765
projects / openwrt / staging / stintel.git / log