Hauke Mehrtens [Thu, 26 Dec 2013 23:27:52 +0000 (23:27 +0000)]
brcm47xx: b44: This updates the phylib patches to the version send upstream
This uses a fixed phy instead of a dummy one.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39166
Hauke Mehrtens [Thu, 26 Dec 2013 23:22:31 +0000 (23:22 +0000)]
kernel: bgmac: update patches
This updates the bgmac backport patch to the current upstream version
and adds some more patches mostly for BCM4707.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39165
Imre Kaloz [Thu, 26 Dec 2013 22:19:29 +0000 (22:19 +0000)]
handle the Linaro version as well
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 39164
John Crispin [Wed, 25 Dec 2013 17:04:50 +0000 (17:04 +0000)]
ramips: add support for RT-N14U (mt7620n based) board
added dts file and userspace scripts modified to support Asus RT-N14U board
current support status:
usb works
ethernet works
buttons reset, wps
leds asus:blue:[usb|lan|wan|air|power]
i2c not tested
uart not tested
wifi not yet
Signed-off-by: Pavel Löbl <lobl.pavel@gmail.com>
SVN-Revision: 39163
John Crispin [Wed, 25 Dec 2013 17:04:34 +0000 (17:04 +0000)]
ramips: add gpio pin 72 in mt7620 chips to dtsi files
describes register set to control last gpio pin on mt7620 platfrom
Signed-off-by: Pavel Löbl <lobl.pavel@gmail.com>
SVN-Revision: 39162
Gabor Juhos [Mon, 23 Dec 2013 17:05:23 +0000 (17:05 +0000)]
ar71xx: fix max frame length of the QCA955x SoCs
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39161
Gabor Juhos [Mon, 23 Dec 2013 17:05:21 +0000 (17:05 +0000)]
ar71xx: don't set builtin_switch flag for QCA9558
It makes no sense, the SoC has no built-in switch.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39160
Gabor Juhos [Mon, 23 Dec 2013 17:05:19 +0000 (17:05 +0000)]
x86/kvm_guest: remove 3.7 support
Patch-by: Stijn Tintel <stijn@linux-ipv6.be>
Patchwork: http://patchwork.openwrt.org/patch/4637/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39159
Gabor Juhos [Mon, 23 Dec 2013 17:05:18 +0000 (17:05 +0000)]
x86/kvm_guest: remove 3.3 support
Patch-by: Stijn Tintel <stijn@linux-ipv6.be>
Patchwork: http://patchwork.openwrt.org/patch/46366/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39158
Gabor Juhos [Mon, 23 Dec 2013 17:05:16 +0000 (17:05 +0000)]
x86/kvm_guest: add support for 3.10 and switch to it
Patch-by: Stijn Tintel <stijn@linux-ipv6.be>
Patchwork: http://patchwork.openwrt.org/patch/4635/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39157
Felix Fietkau [Mon, 23 Dec 2013 12:11:28 +0000 (12:11 +0000)]
hostapd: fix wep with netifd
Signed-off-by: Catalin Patulea <cat@vv.carleton.ca>
SVN-Revision: 39156
Felix Fietkau [Sat, 21 Dec 2013 19:42:45 +0000 (19:42 +0000)]
wpa_supplicant: fix interface combination parsing issues
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 39155
Jo-Philipp Wich [Sat, 21 Dec 2013 13:47:46 +0000 (13:47 +0000)]
opkg: switch to git repository (#14655)
Upstream development now takes place in a git repository which was clone
from the old svn repository. Switch the source location to the git tree
using the commit that corresponds to the old svn r618 revision.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 39153
Jo-Philipp Wich [Sat, 21 Dec 2013 13:31:28 +0000 (13:31 +0000)]
dnsmasq: rework init procedure
- cache udhcp check results to speed up subsequent reloads
- enable procd file tracking for /var/etc/dnsmasq.conf to only reload service if needed
- implement reload action to only restart dnsmasq if /var/etc/dnsmasq.conf actually changed
- launch dnsmasq from interface hotplug to avoid race conditions with network bringup
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 39152
Imre Kaloz [Fri, 20 Dec 2013 20:25:44 +0000 (20:25 +0000)]
change fixup method and fix CFLAGS handling
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 39151
Felix Fietkau [Fri, 20 Dec 2013 16:02:32 +0000 (16:02 +0000)]
ath9k: merge a timer handling fixes
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 39150
Gabor Juhos [Fri, 20 Dec 2013 11:41:23 +0000 (11:41 +0000)]
ar71xx: allow to use large ethernet frames on AR934x SoCs
The hardware supports large ethernet frames. Override
the maximum frame length and packet lenght mask in the
platform data to allow to use large MTU on the ethernet
interfaces.
Limit the feature to AR934x SoCs for now. It should work
on some other SoCs as well, but those has not been tested
yet.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39149
Gabor Juhos [Fri, 20 Dec 2013 11:41:22 +0000 (11:41 +0000)]
ar71xx: ag71xx: fix max frame length setup of the built-in switches
The currently used bitmask of the maximum frame length field
is wrong for both models. On AR724x/AR933x the largest frame
size is 2047 bytes, on the AR934x it is 16383 bytes.
Make the MTU setup code model specific, and use the correct
bitmask for both models. Also change the value to the maximum.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39148
Gabor Juhos [Fri, 20 Dec 2013 11:41:20 +0000 (11:41 +0000)]
ar71xx: ag71xx: calculate max frame len register value from the MTU
Set the MAX_FRAME_LEN register to zero in ag71xx_hw_init()
and write the correct value into that from the ag71xx_open()
and ag71xx_fast_reset() functions.
Also recalculate the RX buffer size based on the actual
maximum frame length value to optimize memory allocation.
Additionaly, disallow to change the MTU value while the
interface it running.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39147
Gabor Juhos [Fri, 20 Dec 2013 11:41:18 +0000 (11:41 +0000)]
ar71xx: ag71xx: add ag71xx_max_frame_len() helper
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39146
Gabor Juhos [Fri, 20 Dec 2013 11:41:17 +0000 (11:41 +0000)]
ar71xx: ag71xx: get max_frame_len and desc_pktlen_mask from platform data
This will allow to use SoC specific values for both.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39145
Gabor Juhos [Fri, 20 Dec 2013 11:41:16 +0000 (11:41 +0000)]
ar71xx: ag71xx: store descriptor packet length mask in ag71xx struct
The currently used bitmask is not correct for all SoCs.
Introduce a new field in struct ag71xx and store the
bitmask in that. Use the current value for now, it will
be adjusted for each SoCs in further patches.
Aslo use the new field directly in the ag71xx_rx_packets
and ag71xx_hard_start_xmit() functions and remove the
ag71xx_desc_pktlen() helper.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39144
Imre Kaloz [Fri, 20 Dec 2013 06:09:41 +0000 (06:09 +0000)]
handle new libs required for new kernels
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 39142
Imre Kaloz [Fri, 20 Dec 2013 05:50:24 +0000 (05:50 +0000)]
don't fail if there are no dtbs
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 39141
Felix Fietkau [Thu, 19 Dec 2013 17:18:12 +0000 (17:18 +0000)]
ar71xx: add missing tx gain table flag for buffalo wzr-hp-g450h
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 39139
Felix Fietkau [Thu, 19 Dec 2013 17:18:07 +0000 (17:18 +0000)]
ath9k: merge another round of upstream (or -pending) fixes and cleanups
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 39138
Luka Perkov [Thu, 19 Dec 2013 02:03:26 +0000 (02:03 +0000)]
imx6: refresh patches
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 39135
Luka Perkov [Thu, 19 Dec 2013 02:03:25 +0000 (02:03 +0000)]
kernel: backport upstream inet fix
Without it in some occasions oops is shown on network restart. Problem was
noticed on imx6 targed.
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 39134
Luka Perkov [Thu, 19 Dec 2013 02:03:16 +0000 (02:03 +0000)]
imx6: proper fix for io-remap
The previous patch was not the proper fix for PCI devices that require io
resources. The new patch is the proper fix backported from mainline.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 39133
Jo-Philipp Wich [Wed, 18 Dec 2013 15:38:28 +0000 (15:38 +0000)]
procd: fix service file tracking
The instance_config_move() function in the procd instance managing code is
missing a blobmsg_list_move() call to update the tracked file items with the
newly calculated checksums in case of a file change.
Without that change, services are always reloaded after the first change to
a tracked file regardless of whether there are any subsequent changes or not.
Add a missing instance of blobmsg_list_free() as well.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 39132
Jo-Philipp Wich [Wed, 18 Dec 2013 12:38:29 +0000 (12:38 +0000)]
netifd: add reload trigger for /etc/config/wireless as well
SVN-Revision: 39131
Gabor Juhos [Tue, 17 Dec 2013 22:14:13 +0000 (22:14 +0000)]
ar71xx: enable images for WD My Net N750
Now that the switch works correctly we can enable the images for this
board.
Flashing from the factory firmware, the factory failsafe loader and
sysupgrade was tested successfully.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4617/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39130
Gabor Juhos [Tue, 17 Dec 2013 22:14:12 +0000 (22:14 +0000)]
ar71xx: fix WD My Net N750 switch led cfg
Now that the switch is working correctly I had the chance to actually
test the LED config.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4616/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39129
Gabor Juhos [Tue, 17 Dec 2013 22:14:11 +0000 (22:14 +0000)]
ar71xx: implement switch fix for WD My Net N750
The bootloader on the WD My Net N750 disables the ports on it's internal
AR8327N switch by powering them down. The stock firmware then brings the
ports back up again by starting the auto negotiation process on each
port.
This fix implements just that.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4615/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39128
Gabor Juhos [Tue, 17 Dec 2013 22:14:10 +0000 (22:14 +0000)]
ar71xx: implement callback in mdio reset
This enables us to add fixups to the board specific code for boards that
require special treatment of PHYs on mdio bus reset.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
http://patchwork.openwrt.org/patch/4614/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39127
Gabor Juhos [Tue, 17 Dec 2013 22:14:07 +0000 (22:14 +0000)]
ar71xx: make ag71xx_mdio_platform_data visible
This enables us to modify the ag71xx_mdio_platform_data from within the
board support files.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4613/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39126
Felix Fietkau [Tue, 17 Dec 2013 20:37:27 +0000 (20:37 +0000)]
busybox: add back support for top-level menuconfig based config overrides (can be used by custom packages to alter the config)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 39125
Jonas Gorski [Tue, 17 Dec 2013 19:05:03 +0000 (19:05 +0000)]
gpio-button-hotplug: fix crash on remove
Don't call gpio_keys_remove recursively. Setting the platform
data to NULL triggered an oops on the second iteration, so there was
no infinate loop.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39124
Jo-Philipp Wich [Tue, 17 Dec 2013 17:17:00 +0000 (17:17 +0000)]
busybox: restore init scripts
Since the removal of the busybox menuconfig entries, the init scripts
for cron, telnet and ntp are not packaged anymore. Unconditionally
ship them from now on.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 39123
Jo-Philipp Wich [Tue, 17 Dec 2013 16:59:47 +0000 (16:59 +0000)]
firewall: fix handling of tcp_ecn parameter
The firewall3 implementation as well as the shell implementation predating it
used to process the tcp_ecnoption as boolean while it actually is an integer.
Change the code to parse tcp_ecn as integer.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 39122
Gabor Juhos [Tue, 17 Dec 2013 16:27:46 +0000 (16:27 +0000)]
ar71xx: ag71xx: compute the RX buffer size from the maximum frame size
Currently, the AG71XX_RX_PKT_SIZE value limits the received
frame size to 1514/1516 bytes with/without a VLAN header
respectively. However the hardware limit is controlled by
the value the AG71XX_REG_MAC_MFL register which contains
the value of the max_frame_len field.
Compute the RX buffer size from the max_frame_len field
to get rid of the 1514/1516 byte limitation. Also remove
the unused AG71XX_RX_PKT_SIZE definition.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39121
Gabor Juhos [Tue, 17 Dec 2013 16:27:44 +0000 (16:27 +0000)]
ar71xx: ag71xx: store RX buffer size in the ag71xx struct
This allows to change the value dynamically.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39120
Felix Fietkau [Tue, 17 Dec 2013 15:59:29 +0000 (15:59 +0000)]
iproute2: reduce .ipk package size from ~100k down to ~60k
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 39119
Felix Fietkau [Tue, 17 Dec 2013 15:59:25 +0000 (15:59 +0000)]
busybox: disable module utils, kmodloader provides them
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 39118
Gabor Juhos [Tue, 17 Dec 2013 15:18:16 +0000 (15:18 +0000)]
ar71xx: ag71xx: store maximum frame length in the ag71xx struct
This will allow to use different values for the
different SoCs.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39117
Gabor Juhos [Tue, 17 Dec 2013 15:12:52 +0000 (15:12 +0000)]
ar71xx: ag71xx: use mdio bus name in ar7240_probe messages
The ar7240_probe function uses the network device name
in the kernel log messages, however the name is not yet
initialized when the ar7240_probe function is called.
Use the mdio bus name in the messages to avoid ugly
log lines like the following one:
eth%d: Found an AR7240/AR9330 built-in switch
Reported-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39116
Gabor Juhos [Tue, 17 Dec 2013 15:12:50 +0000 (15:12 +0000)]
ag71xx: ag71xx: use device name for debugfs entry
The ag71xx debugfs code uses the network device name
for the device specific debugfs directory. Since r38689
'ar71xx: ag71xx: fix a race involving netdev registration'
the debugfs initialization happens before the ethernet
device gets registered and the network device name contains
'eth%d' at this point. If the board setup code registers
multiple ag71xx devices, the debugfs code tries to create
the device specific dir with the same name which causes
an error like this:
eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=
004dd041, driver=Generic PHY]
ag71xx: probe of ag71xx.0 failed with error -12
Use the device name for the debugfs directory to avoid the
collisions. Also add an error message and change the return
code if the debugfs_create_dir call fails.
Reported-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39115
Felix Fietkau [Tue, 17 Dec 2013 07:17:00 +0000 (07:17 +0000)]
busybox: fix typo in Config.in (#14628)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 39114
Luka Perkov [Tue, 17 Dec 2013 02:47:20 +0000 (02:47 +0000)]
imx6: ventana: add canbus utils
Some of the Gateworks Ventana boards have CAN bus support, therefore
we will install the userspace utils.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 39113
Luka Perkov [Tue, 17 Dec 2013 02:47:18 +0000 (02:47 +0000)]
imx6: ventana: add default kernel modules for GSC
All Gateworks Ventana boards have a Gateworks System Controller
which emulates the following:
- ds1672 RTC
- pca953x GPIO expander
- hardware monitor
- at24 eeprom
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 39112
Luka Perkov [Tue, 17 Dec 2013 02:47:17 +0000 (02:47 +0000)]
imx6: add rtc feature support
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 39111
Luka Perkov [Tue, 17 Dec 2013 02:47:16 +0000 (02:47 +0000)]
kernel: add rtc-ds1672 module support
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 39110
Luka Perkov [Tue, 17 Dec 2013 02:47:15 +0000 (02:47 +0000)]
imx6: drop upstreamed patch
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 39109
Luka Perkov [Tue, 17 Dec 2013 02:47:13 +0000 (02:47 +0000)]
automake: update to 1.11.6
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 39108
Felix Fietkau [Mon, 16 Dec 2013 19:27:35 +0000 (19:27 +0000)]
busybox: add support for config overrides via env/busybox-config
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 39107
Felix Fietkau [Mon, 16 Dec 2013 19:09:57 +0000 (19:09 +0000)]
busybox: remove busybox menuconfig from top level menuconfig
This will help with avoiding bogus bug reports caused by stale configs
and bad cases of user tinkering :)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 39106
Felix Fietkau [Mon, 16 Dec 2013 18:49:10 +0000 (18:49 +0000)]
uClibc: disable sha256 and sha512 for libcrypt - saves about 13k uncompressed in libcrypt
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 39105
Felix Fietkau [Mon, 16 Dec 2013 18:42:43 +0000 (18:42 +0000)]
hostapd: move old wifi setup scripts to hostapd-common-old
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 39103
Gabor Juhos [Mon, 16 Dec 2013 18:08:51 +0000 (18:08 +0000)]
ar71xx: add initial support for the Mikrotik RB911G/RB912UAG boards
It is only on RB911G-5HPnD and RB912UAG-5HPnD boards.
The LEDs and the USB port is not working yet.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39102
Jo-Philipp Wich [Mon, 16 Dec 2013 16:47:41 +0000 (16:47 +0000)]
dnsmasq: switch to /lib/functions/network.sh
This commit changes the dnsmasq init script to use the interface
status exposed by netifd. The old references to scan_interfaces()
and (indirect) accesses to uci state variables are removed and
replaced with corresponding network_*() calls.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 39101
Jo-Philipp Wich [Mon, 16 Dec 2013 16:29:23 +0000 (16:29 +0000)]
base-files: ipcalc.sh: support bit length as netmask parameter
SVN-Revision: 39100
Jo-Philipp Wich [Mon, 16 Dec 2013 16:28:45 +0000 (16:28 +0000)]
base-files: add network_get_protocol() to /lib/functions/network.sh
SVN-Revision: 39099
Felix Fietkau [Mon, 16 Dec 2013 15:45:57 +0000 (15:45 +0000)]
mac80211: fix AP mode scanning issues
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 39098
Gabor Juhos [Mon, 16 Dec 2013 12:57:24 +0000 (12:57 +0000)]
ar71xx: add NAND driver for the Mikrotik RB91x boards
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39097
Gabor Juhos [Mon, 16 Dec 2013 12:41:48 +0000 (12:41 +0000)]
ar71xx: rb2011: use board name from the hardware config
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39096
Gabor Juhos [Mon, 16 Dec 2013 10:28:42 +0000 (10:28 +0000)]
ar71xx: rb2011: simplify setup code
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39095
Gabor Juhos [Mon, 16 Dec 2013 10:28:41 +0000 (10:28 +0000)]
ar71xx: rb2011: use the new RouterBOOT helpers
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39094
John Crispin [Mon, 16 Dec 2013 10:16:33 +0000 (10:16 +0000)]
ralink: fix dir810 networking
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 39093
Gabor Juhos [Mon, 16 Dec 2013 10:11:02 +0000 (10:11 +0000)]
ar71xx: rb95x: use the rb_get_wlan_data helper
Also remove unused RB_* defines.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39092
Gabor Juhos [Mon, 16 Dec 2013 10:11:01 +0000 (10:11 +0000)]
ar71xx: add some RouterBOOT specific helper functions
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39091
Gabor Juhos [Mon, 16 Dec 2013 10:11:00 +0000 (10:11 +0000)]
kernel: define RB_ID_HW_OPTIONS in include/linux/routerboot.h
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39090
Gabor Juhos [Mon, 16 Dec 2013 10:10:58 +0000 (10:10 +0000)]
ar71xx: refresh m25p80 patches
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39089
Felix Fietkau [Mon, 16 Dec 2013 10:08:13 +0000 (10:08 +0000)]
netifd: update to latest version, fixes a null pointer crash
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 39088
Gabor Juhos [Mon, 16 Dec 2013 08:17:40 +0000 (08:17 +0000)]
ar71xx: rb95x: nuke rb95x_gpio_init
Set up the chipselect GPIO directly in rb95x_nand_init
instead.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39087
Gabor Juhos [Mon, 16 Dec 2013 08:16:09 +0000 (08:16 +0000)]
kernel/3.1[02]: add Winbond W25X05 SPI flash support
It is used on newer RouterBOARDs.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39086
Gabor Juhos [Mon, 16 Dec 2013 07:51:21 +0000 (07:51 +0000)]
kernel: remove obsolete yaffs options from target configs
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39085
Gabor Juhos [Mon, 16 Dec 2013 07:51:19 +0000 (07:51 +0000)]
kernel: update yaffs code
Use the latest version of the yaffs code. Fetched from the
yaffs2 git tree and it is based on the following commit:
commit
bc76682d93955cfb33051beb503ad9f8a5450578
Merge:
3a8580e ffa781d
Author: Charles Manning <cdhmanning@gmail.com>
Date: Thu Jul 11 17:46:25 2013 +1200
Merge branch 'master' of ssh://www.aleph1.co.uk/home/aleph1/git/yaffs2
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39084
Gabor Juhos [Mon, 16 Dec 2013 07:42:43 +0000 (07:42 +0000)]
kernel/3.9: remove yaffs patches
It is not used by any platform.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39083
Gabor Juhos [Mon, 16 Dec 2013 07:42:42 +0000 (07:42 +0000)]
kernel/3.6: remove yaffs support
It is not used by any platform.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39082
Gabor Juhos [Mon, 16 Dec 2013 07:42:41 +0000 (07:42 +0000)]
kernel/3.3: remove yaffs support
It is not used by any platform.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39081
Gabor Juhos [Mon, 16 Dec 2013 07:39:22 +0000 (07:39 +0000)]
ar71xx/mikrotik: disable unused MTD options
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39080
Gabor Juhos [Mon, 16 Dec 2013 07:37:31 +0000 (07:37 +0000)]
ar71xx: add dummy rle_decode function if CONFIG_RLE_DECOMPRESS is not set
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39079
Gabor Juhos [Mon, 16 Dec 2013 07:16:43 +0000 (07:16 +0000)]
ar71xx: add userspace support for WD My Net N750
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
[juhosg: remove the image generation part until the ethernet
switch issue is resolved]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39078
Gabor Juhos [Mon, 16 Dec 2013 07:16:42 +0000 (07:16 +0000)]
ar71xx: add kernel support for WD My Net N750
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
[juhosg: use a separate patch for kernel changes]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39077
Gabor Juhos [Sun, 15 Dec 2013 22:18:04 +0000 (22:18 +0000)]
generic: ar8216: Enable jumbo frames on AR8327 by default
This patch enables jumbo frames on AR8327 switch by default.
I have tested it on TP-Link TL-WDR3600.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39076
Gabor Juhos [Sun, 15 Dec 2013 21:34:20 +0000 (21:34 +0000)]
ar71xx: build image for the TP-Link TL-WA901ND v3 board
Based-on: http://patchwork.openwrt.org/patch/4507/
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39075
Gabor Juhos [Sun, 15 Dec 2013 21:34:19 +0000 (21:34 +0000)]
ar71xx: add user-space support for the TP-Link TL-WA901ND v3 board
Based-on: http://patchwork.openwrt.org/patch/4508/
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39074
Gabor Juhos [Sun, 15 Dec 2013 21:34:18 +0000 (21:34 +0000)]
ar71xx: add kernel support for the TL-WA901ND v3 board
Based-on: http://patchwork.openwrt.org/patch/4506/
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39073
Gabor Juhos [Sun, 15 Dec 2013 21:34:17 +0000 (21:34 +0000)]
ar71xx: move TL-WA801ND v2 setup code
The TL-WA801ND v2 board has only one LAN port which makes
it more similar to the TL-WR[78]50RE devices. Move the
board setup code into the mach-tl-wax50re.c file.
Based-on: http://patchwork.openwrt.org/patch/4506/
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39072
Gabor Juhos [Sun, 15 Dec 2013 21:34:15 +0000 (21:34 +0000)]
ar71xx: refactor TL-WAx50RE setup code
This way it is a bit easier to add other TP-LINK devices based on the
Atheros AP123 reference board with one LAN port.
Based-on: http://patchwork.openwrt.org/patch/4506/
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39071
Luka Perkov [Sun, 15 Dec 2013 21:07:34 +0000 (21:07 +0000)]
ppl: update to 1.1
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 39068
Luka Perkov [Sun, 15 Dec 2013 21:07:32 +0000 (21:07 +0000)]
cloog: update to 0.18.1
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 39067
Gabor Juhos [Sun, 15 Dec 2013 20:39:13 +0000 (20:39 +0000)]
firmware-utils/mkplinkfw: add TL-WA801ND v2 support
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Patchwork: http://patchwork.openwrt.org/patch/4503/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39066
Gabor Juhos [Sun, 15 Dec 2013 20:39:12 +0000 (20:39 +0000)]
ar71xx: build firmware image for the TL-WA801ND v2
Patch to add the profile for the TP-LINK WA801ND v2
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Patchwork: http://patchwork.openwrt.org/patch/4502/
[juhosg: change subject]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39065
Gabor Juhos [Sun, 15 Dec 2013 20:39:11 +0000 (20:39 +0000)]
ar71xx: add user space support for the TL-WA801ND v2
Patch to add the user space support for the TL-WA801ND v2
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Patchwork: http://patchwork.openwrt.org/patch/4501/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39064
Gabor Juhos [Sun, 15 Dec 2013 20:39:10 +0000 (20:39 +0000)]
ar71xx: add kernel support for the TL-WA801ND v2 board
Patch to add kernel support for the TP-LINK WA801ND v2
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Patchwork: http://patchwork.openwrt.org/patch/4500/
[juhosg:
- the TL-WA801ND v2 does not have a sliding switch, it uses a push button
for WPS instead. Use the tl_mr3420v2_gpio_keys array to reflect that,
- rename kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39063
Felix Fietkau [Sun, 15 Dec 2013 20:23:00 +0000 (20:23 +0000)]
ath9k: fix interrupt storms on AR913x
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 39062
Steven Barth [Sun, 15 Dec 2013 19:38:53 +0000 (19:38 +0000)]
Convert DHCP->6rd and DHCPv6->DS-Lite autoconfig to dynamic interface
SVN-Revision: 39061
Hauke Mehrtens [Sun, 15 Dec 2013 19:19:16 +0000 (19:19 +0000)]
brcm47xx: deactivate early printk support
This breaks some devices where the serial console is not at port 0 but
somewhere else.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39060
Hauke Mehrtens [Sun, 15 Dec 2013 19:16:30 +0000 (19:16 +0000)]
kernel: update kernel 3.10 to 3.10.24
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39059
projects / openwrt / staging / chunkeey.git / log