Daniel Golle [Sun, 10 Dec 2023 23:09:00 +0000 (23:09 +0000)]
mediatek: bananapi-r3: add overlay for ReSpeaker 2-mic hat
Add DT overlay to allow using the ReSpeaker 2-mic hat connected to
the 26-pin header of the BananaPi BPi-R3.
Supported sample formats: S16_LE, S24_LE, S32_LE
Supported sample rates: 8/12/16/24/32/48/96/192 kHz
| BPi-R3 | ReSpeaker 2-mic
Signal | 26-pin | 40-pin
----------+----------+-------------------
VCC 5V | 2 | 2
I2C SDA | 3 | 3
I2C SCL | 5 | 5
GND | 6 | 6
PCM CLK | 12 | 12
PCM FS | 15 | 35
PCM DIN | 26 | 38
GND | 25 | 39
PCM DOUT | 22 | 40
Once connected, install the driver and tell U-Boot to apply the DT
overlay:
opkg kmod-sound-soc-mt7986-wm8960
fw_setenv bootconf_base "config-mt7986a-bananapi-bpi-r3#mt7986a-bananapi-bpi-r3-respeaker-2mics"
reboot
To setup the ReSpeaker for Stereo out on the Headphone plug:
amixer sset 'Right Output Mixer PCM' on
amixer sset 'Left Output Mixer PCM' on
amixer sset 'PCM Playback -6dB' off
amixer sset 'O018 I150_Switch' on
amixer sset 'O019 I151_Switch' on
amixer sset 'O124 I032_Switch' on
amixer sset 'O125 I033_Switch' on
amixer sset 'Headphone' 121
amixer sset 'Playback' 255
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Thu, 28 Sep 2023 18:13:23 +0000 (19:13 +0100)]
kernel: modules: package MT7986 audio drivers
Packages the audio drivers for the MediaTek MT7986 SoC used with
Wolfson WM8960 codec.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Mon, 11 Dec 2023 00:24:40 +0000 (00:24 +0000)]
kernel: modules: break-out WM8960 codec module
Package codec module for WM8960 in its own package to be used by more
than one target.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Maso Huang [Thu, 7 Sep 2023 08:40:19 +0000 (16:40 +0800)]
mediatek: backport MT7986 audio driver
Pick commits adding drivers for audio engine found in MT7986 from
Linux 6.6 as well as follow-up fixes from Linux 6.7.
Signed-off-by: Maso Huang <maso.huang@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
John Audia [Fri, 8 Dec 2023 13:12:51 +0000 (08:12 -0500)]
kernel: bump 5.15 to 5.15.142
Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.142
All patches automatically rebased.
Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3
Signed-off-by: John Audia <therealgraysky@proton.me>
Nick Hainke [Sat, 11 Nov 2023 03:18:18 +0000 (04:18 +0100)]
iproute2: update to 6.6.0
Release Notes:
https://lore.kernel.org/netdev/
20231106090325.
07092c87@hermes.local/T/
Automatically refreshed:
- 115-add-config-xtlibdir.patch
- 175-reduce-dynamic-syms.patch
- 195-build_variant_ip_tc.patch
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Sat, 11 Nov 2023 03:23:58 +0000 (04:23 +0100)]
strace: update to 6.6
Release Notes:
https://github.com/strace/strace/releases/tag/v6.6
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Thu, 7 Dec 2023 12:30:40 +0000 (13:30 +0100)]
util-linux: update to v2.39.3
Changes:
2da5c904e build-sys: release++ (v2.39.3)
03c939edd docs: update v2.39.3-ReleaseNotes
dafb120ef docs: update AUTHORS file
bfc9691ce po-man: merge changes
d2232b609 po: merge changes
4ab356c1c po: add ro.po (from translationproject.org)
7e147d16c po: update es.po (from translationproject.org)
e8cb61f07 lsfd: fix memory leak in append_filter_expr()
192d8aaa0 lsfd: avoid undefined behavior
756588f8c lsfd: (man) fix the form for the optional argument of --inet option
8d78c1306 Add Phytium FTC310 & FTC664 support
b75322cdb Add Phytium FTC862 cpu model. fix:#2486
ec1b0eb36 libmount: accept '\' as escape for options separator
2e5f5c8d8 tests: add ts_skip_docker
0b3254cac Merge branch 'stable-2.39/bcachefs-fixes' of https://github.com/t-8ch/util-linux into PR/stable-v2.39.3
649843934 tests: skip broken tests on docker
fa9b53658 libblkid: (bcachefs) add support for sub-device labels
3c5d991b0 libblkid: (bcachefs) adapt to major.minor version
ece194082 libuuid: avoid truncate clocks.txt to improve performance
84a62c1a5 libuuid/src/gen_uuid.c: fix cs_min declaration
93239aa78 libmount: fix possible NULL dereference [coverity scan]
a6def815e meson: install wall executable with group 'tty'
c6c1c69c3 meson: install write executable with group 'tty'
bf2cd1d5a libmount: improve mnt_table_next_child_fs()
c14f5bf37 docs: add SPDX to boilerplate.c
fdd9f11f5 disk-utils: add SPDX and Copyright notices
e7dbe9c78 include/audit-arch: add missing SPDX
5ec7b14a7 setterm: avoid restoring flags from uninitialized memory
64d2300e6 Fix man page for col to correct documentation error
7cc2c9625 Update col.c to fix option mistake
122d7e7af umount: handle bindmounts during --recursive
da18b31ff lscpu: fix caches separator for --parse=<list>
3a5c9c1dd Use empty libuser config file.
7058d793d libblkid: exfat: fix fail to find volume label
d065ff00a blkpr: store return value of getopt_long in int
9ca6f1712 lib/path: Set errno in case of fgets failure
e2f0aa5c2 autotools: fix AC_DEFINE_UNQUOTED() use
cefd05c47 autotools: fix librtas check
f27fbafb2 lib/path: fix typos
f8ab70477 lib/path: set errno in case of error
5ec30a362 lib/path: fix possible out of boundary access
edc723cd3 libblkid: reset errno before calling probefuncs
8de89778b setpriv: fix group argument completion
41599054c libfdisk: reset errno before calling read()
cce4e4405 blkid: fix call to err_exclusive_options
b718f985c docs: use HTTPS for GitHub clone URLs
2bddfa692 libblkid: (probe) handle probe without chain gracefully
3d3121678 lib/idcache: always gracefully handle null cache
368521e45 script-playutils: close filestream in case ignore_line() fails
087b0d238 libblkid: (vxfs) report endianness
7e5056f33 libblkid: (ntfs) validate that sector_size is a power of two
f368ccc75 libsmartcols: handle nameless tables in export format
f5cace8da ldattach: don't call exit() from signal handler
03c12a34c lslogins: fix realloc() loop allocation size
83ba179b1 lib/env: avoid underflow of read_all_alloc() return value
813851fba libblkid: avoid memory leak of cachefile path
4459623cd libmount: gracefully handle NULL path in mnt_resolve_target()
dbde7a537 more: avoid out-of-bound access
c26badd5d libfdisk: handle allocation failure in fdisk_new_partition
5c250aa64 login: Use pid_t for child_pid
be3f1712e login: move comment
98be90b5b build-sys: fix libmount/src/hooks.c use
a711af02d lscpu: Use 4K buffer size instead of BUFSIZ
45c6136cb autotools: fix typos
aa98c4ecc libmount: make.stx_mnt_id use more robust
c697c2bb6 libmount: report statx in features list
13711f3ab libmount: fix statx() includes
e9ed5a2b8 libblkid: (vfat) avoid modifying shared buffer
d2cadf099 libblkid: (jmicron_raid) use checksum APIs
c54c99efd libblkid: (jmicron_raid) avoid modifying shared buffer
64418c52b libblkid: (zonefs) avoid modifying shared buffer
b66da7ce4 losetup: fix JSON MAJ:MIN
44d7bf2c8 lslogins: (man) fix -y option formatting
7d6c71e51 include: add DragonFlyBSD GPT partition types
6b9fda87c libblkid: (bcachefs) fix size validation
acbf17ae8 libblkid: (bcachefs) fix compiler warning [-Werror=sign-compare]
1ec71634a libblkid: (bcachefs) fix not detecting large superblocks
68564ebb5 libmount: Fix regression when mounting with atime
Signed-off-by: Nick Hainke <vincent@systemli.org>
Felix Fietkau [Mon, 11 Dec 2023 12:15:09 +0000 (13:15 +0100)]
mt76: update to Git HEAD (2023-12-11)
f63f87cd5b45 wifi: mt76: mt7996: fix shift overflow warning on 32 bit systems
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Christian Marangi [Sun, 10 Dec 2023 10:43:45 +0000 (11:43 +0100)]
lua5.3: fix typo calling lua53 instead of lua5.3 for Package Default
Fix typo calling lua53 instead of lua5.3 for Package Default definition.
This cause only missing description of the package and doesn't cause
any build regression.
Fixes: c52ca08d4008 ("lua5.3: build shared library")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Daniel Golle [Fri, 17 Nov 2023 02:25:09 +0000 (02:25 +0000)]
mediatek: add support for Adtran SmartRG Bonanza Peak series
The Bonanza Peak series are a couple of MT7986-powered 2.5 GBit/s
Wi-Fi 6 residential gateway, access point and mesh router products.
All of them come with an eMMC to boot from, are powered via USB-C and
got a USB 3.0 type-A port. All of them got a Dialog (Renesas)
DA14531
Bluetooth module connected via UART. If the device was previously
running stock firmware, the BT chip's internal flash has been loaded
with firmware and it can be attached using hciattach when using
OpenWrt.
SOC: MediaTek MT7986A
RAM: 2 GiB DDR4
eMMC: 8 GiB
Bluetooth: BLE5 (
DA14531)
Serial: 3.3V level, 115200 8n1 on 4-pin connector
* SDG-8612 - Dual-band RJ-45 gateway
2x 2.5G MaxLinear PHY for WAN port
3x 1GE LAN ports via MT7531 switch
* SDG-8614 - Dual-band SFP gateway
1x SFP cage with up to 2.5G speed
1x 2.5G MaxLinear PHY for LAN port
3x 1GE LAN ports via MT7531 switch
* SDG-8622 - Tri-band mesh router
2x 2.5G MaxLinear PHY
The MT7986 2G and 5G are used as 2G and 5G high band.
There’s a MT7915 PCIe card for 5G low band.
* SDG-8632 - Tri-band mesh router with 6 GHz
2x 2.5G MaxLinear PHY
The MT7986 serves the 2G and 6G bands.
There’s a MT7915 PCIe card for 5G.
Installation via U-Boot serial console:
0. setup TFTP server with IP 192.168.1.10/24, place initramfs image
renamed to openwrt.XXX where XXX is the internal product number:
SDG-8612: XXX = 412
SDG-8614: XXX = 414
SDG-8622: XXX = 422
SDG-8632: XXX = 432
1. connect to the serial console and power on the device.
Interrupt the bootloader by pressing 'st'
2. setenv boot_mode openwrt ; saveenv
3. run boot1
Load firmware via TFTP and write to flash
4. run boot2
Now OpenWrt initramfs should boot
5. upload sysupgrade.bin via scp to /tmp
6. sysupgrade
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 17 Nov 2023 02:01:34 +0000 (02:01 +0000)]
mediatek: import driver for Adtran SmartRG RGBW LED
Import driver for I2C-connected HolTek MCU controlling the RGBW LED
found in Adtran SmartRG devices.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sun, 10 Dec 2023 01:15:36 +0000 (01:15 +0000)]
kernel: hack: support inverted LEDs on MaxLinear GPY211 PHY
Add downstream DT property to setup the PHY LEDs of the MaxLinear
GPY211 PHY in such way that the VDD of the LED is driven by the SoC
pin rather than the GND (which is the default).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 17 Nov 2023 00:02:05 +0000 (00:02 +0000)]
base-files: add mmc_get_mac_ascii function
Similar to the *_get_mac_binary function, also split the common parts
off mtd_get_mac_ascii into new get_mac_ascii function and introduce
mmc_get_mac_ascii which uses it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Andrey VOLKOV [Sat, 2 Dec 2023 21:03:31 +0000 (22:03 +0100)]
generic: 6.1: fix patch 814 Add Qualcomm secure QFPROM support
The backported patch is broken, since kernel 6.1 has not
'include/linux/firmware' directory yet.
Fix the include to the correct path.
Fixes: #14115
Fixes: 52c365f055f6 ("kernel: backport v6.6 nvmem changes")
Signed-off-by: Andrey VOLKOV <andrey@volkov.fr>
[ improve commit description and title ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Rosen Penev [Wed, 29 Nov 2023 00:41:20 +0000 (16:41 -0800)]
kernel: remove mac-address-ascii dts support
Deprecated and replaced treewide with mac-base. Remove to avoid modern
usage.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Wed, 29 Nov 2023 19:06:38 +0000 (11:06 -0800)]
kernel: of: remove mac-address-increment support hack
The MAC address increment has been replaced by the new "mac-base"
NVMEM fixed layout. This old implementation can be removed now.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Pascal Coudurier [Fri, 1 Dec 2023 21:25:58 +0000 (22:25 +0100)]
x86: kernel: modules: clean makefiles
Signed-off-by: Pascal Coudurier <coudu@gmx.com>
Pascal Coudurier [Fri, 1 Dec 2023 20:49:27 +0000 (21:49 +0100)]
x86: remove unused 5.15 kernel configs and patches
As we move to 6.1 by default, remove unused 5.15 kernel configs and patches
Signed-off-by: Pascal Coudurier <coudu@gmx.com>
Pascal Coudurier [Fri, 1 Dec 2023 20:42:37 +0000 (21:42 +0100)]
x86: move to 6.1 kernel by default
6.1 kernel has been in testing for a few month without issues
Signed-off-by: Pascal Coudurier <coudu@gmx.com>
Rosen Penev [Sat, 2 Dec 2023 01:20:50 +0000 (17:20 -0800)]
ipq806x: fix leading 0 warnings
dtc warns about leading 0s.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Sat, 2 Dec 2023 01:20:19 +0000 (17:20 -0800)]
ipq806x: avoid duplicate partition nodes
Avoids dtc warnings by moving it in a subnode.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Sat, 2 Dec 2023 00:52:27 +0000 (16:52 -0800)]
ipq806x: reset-gpio to reset-gpios
The former is deprecated. Fixes dtc warning.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Christian Marangi [Sat, 9 Dec 2023 13:45:50 +0000 (14:45 +0100)]
ixp4xx: add Generic subtarget definition
Add Generic subtarget definition. This is needed to keep consistent name
on every other target/subtarget and also to permit correct work of CI
workflows that expect a target/subtarget pattern.
Fixes: c16b2293fe71 ("ixp4xx: Resurrect IXP4xx support using device tree")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Daniel Golle [Fri, 8 Dec 2023 23:34:32 +0000 (23:34 +0000)]
ramips: refresh patches
Refresh ramips patches which got out of sync due to backported changes
of the MediaTek Ethernet driver.
Fixes: 6407ef8d2bcb ("kernel: backport upstream mediatek WED changes")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Nick Hainke [Thu, 7 Dec 2023 12:22:48 +0000 (13:22 +0100)]
tools/bash: update to 5.2.21
Update to latest release.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Mon, 4 Dec 2023 16:09:53 +0000 (17:09 +0100)]
toolchain/gdb: update to 14.1
Release Notes:
https://lists.gnu.org/archive/html/info-gnu/2023-12/msg00001.html
Refresh patch:
- 120-fix-compile-flag-mismatch.patch
Signed-off-by: Nick Hainke <vincent@systemli.org>
Felix Fietkau [Fri, 8 Dec 2023 14:52:12 +0000 (15:52 +0100)]
kernel: remove already backported patch, fix build
Fixes: 6407ef8d2bcb ("kernel: backport upstream mediatek WED changes")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Fri, 17 Nov 2023 16:59:29 +0000 (17:59 +0100)]
kernel: backport upstream mediatek WED changes
Reorder and update existing patches
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Nick Hainke [Thu, 7 Dec 2023 12:14:58 +0000 (13:14 +0100)]
tools/pkgconf: update to 2.1.0
Changes:
https://github.com/pkgconf/pkgconf/blob/
5825e2c6d608ef74a97349e81d750ab95c53cf50/NEWS#L4
Signed-off-by: Nick Hainke <vincent@systemli.org>
Felix Fietkau [Mon, 20 Nov 2023 12:57:17 +0000 (13:57 +0100)]
mt76: update to Git HEAD (2023-12-08)
890ae4d717f1 wifi: mt76: mt76x02: fix MT76x0 external LNA gain handling
fcc2f3d82bc9 wifi: mt76: fix lock dependency problem for wed_lock
77cc14596202 wifi: mt76: mt792x: move mt7921_skb_add_usb_sdio_hdr in mt792x module
bc85355885d1 wifi: mt76: mt792x: move some common usb code in mt792x module
c27f01c4c834 wifi: mt76: mt7996: get tx_retries and tx_failed from txfree
30aba4c18307 wifi: mt76: mt7996: Add mcu commands for getting sta tx statistic
119bebff244b wifi: mt76: mt7996: enable PPDU-TxS to host
a4005e0e83e7 wifi: mt76: mt7996: remove periodic MPDU TXS request
d6cc20bf5913 wifi: mt76: reduce spin_lock_bh held up in mt76_dma_rx_cleanup
5d94251d641c wifi: mt76: mt7921: move connac nic capability handling to mt7921
266341b5019d wifi: mt76: mt7921: enable set txpower for UNII-4
581449ac5274 wifi: mt76: mt7921: add 6GHz power type support for clc
9bfd669e9477 wifi: mt76: mt7921: get regulatory information from the clc event
4a0f839da0f1 wifi: mt76: mt7921: update the channel usage when the regd domain changed
f4df423d3d56 wifi: mt76: add ability to explicitly forbid LED registration with DT
54d369e79972 wifi: mt76: mt7921: support 5.9/6GHz channel config in acpi
b39b6cba220f wifi: mt76: mt7996: fix uninitialized variable in parsing txfree
77194e652885 wifi: mt76: fix typo in mt76_get_of_eeprom_from_nvmem function
c37738fc9097 wifi: mt76: limit support of precal loading for mt7915 to MTD only
d6e8aa634a19 wifi: mt76: make mt76_get_of_eeprom static again
d1c671a90eba wifi: mt76: permit to use alternative cell name to eeprom NVMEM load
5539001fe4e3 wifi: mt76: permit to load precal from NVMEM cell for mt7915
48d413380685 wifi: mt76: Remove unnecessary (void*) conversions
ea2814289147 wifi: mt76: mmio: move mt76_mmio_wed_{init,release}_rx_buf in common code
9fb0277d7ee8 wifi: mt76: move mt76_mmio_wed_offload_{enable,disable} in common code
4b47145ecf44 wifi: mt76: move mt76_net_setup_tc in common code
d798d5d6f770 wifi: mt76: introduce mt76_queue_is_wed_tx_free utility routine
48b0cedbf83f wifi: mt76: introduce wed pointer in mt76_queue
c550204e347d wifi: mt76: increase MT_QFLAG_WED_TYPE size
2e7f30f22cfd wifi: mt76: mt7996: add wed tx support
ec8765a02fc8 wifi: mt76: dma: introduce __mt76_dma_queue_reset utility routine
a469aaac9784 wifi: mt76: mt7996: use u16 for val field in mt7996_mcu_set_rro signature
abca260a15c4 wifi: mt76: mt7996: add wed rx support
be2e74c0c495 wifi: mt76: move wed reset common code in mt76 module
7f17e164fbb4 wifi: mt76: mt7996: add wed reset support
0f89bf58efda wifi: mt76: mt7996: add wed rro delete session garbage collector
a58b75f863ca wifi: mt76: mt7915: fallback to non-wed mode if platform_get_resource fails in mt7915_mmio_wed_init()
36d2ddd94eeb wifi: mt76: mt7996: add support for variants with auxiliary RX path
cec7720c9341 wifi: mt76: mt7996: add TX statistics for EHT mode in debugfs
9852093062e8 wifi: mt76: connac: add thermal protection support for mt7996
955540a4df74 wifi: mt76: mt7996: add thermal sensor device support
af41374a3b8e wifi: mt76: connac: add beacon duplicate TX mode support for mt7996
3c98d7b7fa23 wifi: mt76: mt7996: fix the size of struct bss_rate_tlv
ee2169c00539 wifi: mt76: mt7996: adjust WFDMA settings to improve performance
0aead5de68a7 wifi: mt76: connac: set fixed_bw bit in TX descriptor for fixed rate frames
ab5580ff5a4f wifi: mt76: mt7996: handle IEEE80211_RC_SMPS_CHANGED
eed234afed7e wifi: mt76: mt7996: align the format of fixed rate command
d9a855285b95 wifi: mt76: mt7996: fix rate usage of inband discovery frames
47799aefe263 wifi: mt76: change txpower init to per-phy
264e1ecfe1b4 wifi: mt76: mt7996: add txpower setting support
c7b243b127eb wifi: mt76: use chainmask for power delta calculation
05f433900a02 wifi: mt76: mt7996: switch to mcu command for TX GI report
ae963198e605 wifi: mt76: mt7996: fix alignment of sta info event
d0d2e03591d6 wifi: mt76: mt7996: rework ampdu params setting
e87f4efc7638 wifi: mt76: connac: add beacon protection support for mt7996
0dfcc53a8e5d wifi: mt76: connac: fix EHT phy mode check
30c54a53bf8b wifi: mt76: mt7915: fix EEPROM offset of TSSI flag on MT7981
17297c97b737 wifi: mt76: mt7915: also MT7981 is 3T3R but nss2 on 5 GHz band
eeb48c081034 wifi: mt76: mt7996: fix mt7996_mcu_all_sta_info_event struct packing
b74ad922659c wifi: mt76: mt7996: introduce mt7996_band_valid()
51cb541c1e53 wifi: mt76: connac: add firmware support for mt7992
c0eda4d96ec8 wifi: mt76: mt7996: add DMA support for mt7992
f12471968a53 wifi: mt76: mt7996: rework register offsets for mt7992
8d11dae73eb8 wifi: mt76: mt7996: support mt7992 eeprom loading
6c2b2c37abd7 wifi: mt76: mt7996: adjust interface num and wtbl size for mt7992
df1d3b3c67e5 wifi: mt76: connac: add new definition of tx descriptor
f997e759cea5 wifi: mt76: mt7996: add PCI IDs for mt7992
94e3632e4e93 wifi: mt76: mt7925: remove iftype from mt7925_init_eht_caps signature
9c7b98c03173 net: ethernet: mtk_wed: rename mtk_rxbm_desc in mtk_wed_bm_desc
4423b4eb69fb wifi: mt76: mt7996: fix endianness in mt7996_mcu_wed_rro_event
b97d899a7907 wifi: mt76: mt7921: fix kernel panic by accessing invalid 6GHz channel info
9ef06028d4fe wifi: mt76: mt7921s: fix workqueue problem causes STA association fail
95c14207d2a9 wifi: mt76: mt7996: set DMA mask to 36 bits for boards with more than 4GB of RAM
dbea5151412b wifi: mt76: mt7921: reduce the size of MCU firmware download Rx queue
a84a355d2e0a wifi: mt76: mt7921: fix country count limitation for CLC
c498f27ad075 wifi: mt76: mt7921: fix CLC command timeout when suspend/resume
3098d968abe4 wifi: mt76: mt7921: fix wrong 6Ghz power type
7730fc91dd15 wifi: mt76: fix shift overflow warnings on 32 bit systems
f559adf1849c wifi: mt76: fix crash with WED rx support enabled
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Jo-Philipp Wich [Thu, 7 Dec 2023 22:12:00 +0000 (23:12 +0100)]
ucode: adjust module dependencies
Let ucode-mod-* packages select the ucode interpreter instead of depending
on it to avoid recursive dependency chains in unrelated packages.
Fixes: https://github.com/openwrt/packages/issues/22837
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Nick Hainke [Mon, 4 Dec 2023 15:48:00 +0000 (16:48 +0100)]
tools/cmake: update to 3.27.9
Release Notes:
- https://www.kitware.com/cmake-3-27-7-available-for-download/
- https://www.kitware.com/cmake-3-27-9-available-for-download/
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Mon, 4 Dec 2023 16:03:21 +0000 (17:03 +0100)]
libxml2: update to 2.12.1
Release Notes:
- https://gitlab.gnome.org/GNOME/libxml2/-/releases/v2.12.0
- https://gitlab.gnome.org/GNOME/libxml2/-/releases/v2.12.1
Remove patch:
- 010-iconv.patch
Signed-off-by: Nick Hainke <vincent@systemli.org>
Kamil Jońca [Sun, 5 Nov 2023 13:49:01 +0000 (14:49 +0100)]
ramips: add TP-LINK TL-WR902AC v4
Seems to be very similar to: https://openwrt.org/toh/tp-link/tl-wr902ac_v3
1 x usb
1 x eth
Powered by mini usb port.
Installation:
Can use TFTP method to install:
1. establish TFTP server at 192.168.0.66
2. provide tp_recover.bin file to the TFTP server
3. turn on router with reset button pressed
4. wait for led blinking, then release reset
Specification based on dmesg from already flashed device:
SoC Type: MediaTek MT7628AN ver:1 eco:2
CPU0 revision is:
00019655 (MIPS 24KEc)
Memory: 56028K/65536K available
CPU Clock: 580MHz
WiFi: MT7613BE
MAC addresses are all the same, except wifi5g which last part is decrement by one, ie.:
eth0 40:ed:00:cf:b9:9b
br-lan 40:ed:00:cf:b9:9b
phy0-ap0 40:ed:00:cf:b9:9b
phy1-ap0 40:ed:00:cf:b9:9a
Signed-off-by: Kamil Jońca <kjonca@onet.pl>
Hannu Nyman [Wed, 6 Dec 2023 12:49:42 +0000 (14:49 +0200)]
ipq806x: Fix nighthawk R7800/XR450/XR500 wan MAC
Correct the NVMEM mac-base field usage to read the wan MAC
correctly from flash.
Reference to discussion at https://github.com/openwrt/openwrt/pull/13952#issuecomment-
1842749122
Fixes: d264d3a60 ("ipq806x: remove mac-address-increment")
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Luis Mita [Wed, 6 Dec 2023 13:30:10 +0000 (09:30 -0400)]
mediatek: add SPDX header for Confiabits MT7981 DTS
Fixing ambiguous licensing.
Signed-off-by: Luis Mita <luis@luismita.com>
Felix Fietkau [Wed, 6 Dec 2023 15:17:21 +0000 (16:17 +0100)]
udebug: update to Git HEAD (2023-12-06)
6d3f51f9fda7 ucode: check for errors in ftruncate()
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Mikhail Zhilkin [Sat, 25 Nov 2023 12:14:57 +0000 (12:14 +0000)]
ramips: add support for Rostelecom RT-FE-1A
Rostelecom RT-FE-1A is a wireless WiFi 5 router manufactured by Sercomm
company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB
Flash: 128 MiB
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615E): a/n/ac, 4x4
Ethernet: 5x GbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: No
Button: 2 buttons (Reset & WPS)
LEDs:
- 1x Power (green, unmanaged)
- 1x Status (green, gpio)
- 1x 2.4G (green, hardware, mt76-phy0)
- 1x 2.4G (blue, gpio)
- 1x 5G (green, hardware, mt76-phy1)
- 1x 5G (blue, gpio)
- 5x Ethernet (green, hardware, 4x LAN & WAN)
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot
Installation
-----------------
1. Login to the router web interface (default http://192.168.0.1/)
under "admin" account
2. Navigate to Settings -> Configuration -> Save to Computer
3. Decode the configuration. For example, using cfgtool.py tool (see
related section):
cfgtool.py -u configurationBackup.cfg
4. Open configurationBackup.xml and find the following block:
<OBJECT name="User." type="object" writable="1" encryption="0" >
<OBJECT name="1." type="object" writable="1" encryption="0" >
<PARAMETER name="Password" type="string" value="<some value>" writable="1" encryption="1" password="1" />
</OBJECT>
5. Replace <some value> by a new superadmin password and add a line
which enabling superadmin login after. For example, the block after
the changes:
<OBJECT name="User." type="object" writable="1" encryption="0" >
<OBJECT name="1." type="object" writable="1" encryption="0" >
<PARAMETER name="Password" type="string" value="s0meP@ss" writable="1" encryption="1" password="1" />
<PARAMETER name="Enable" type="boolean" value="1" writable="1" encryption="0"/>
</OBJECT>
6. Encode the configuration. For example, using cfgtool.py tool:
cfgtool.py -p configurationBackup.xml
7. Upload the changed configuration (configurationBackup_changed.cfg) to
the router
8. Login to the router web interface (superadmin:xxxxxxxxxx, where
xxxxxxxxxx is a new password from the p.5)
9. Enable SSH access to the router (Settings -> Access control -> SSH)
10. Connect to the router using SSH shell using superadmin account
11. Run in SSH shell:
sh
12. Make a mtd backup (optional, see related section)
13. Change bootflag to Sercomm1 and reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
reboot
14. Login to the router web interface under admin account
15. Remove dots from the OpenWrt factory image filename
16. Update firmware via web using OpenWrt factory image
Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
cd /tmp
for i in 0 1 2 3 4 5 6 7 8 9; do nanddump -f mtd$i /dev/mtd$i; \
tftp -l mtd$i -p 192.168.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
tftp -l mtd.md5 -p 192.168.0.2
MAC Addresses
-------------
+-----+------------+---------+
| use | address | example |
+-----+------------+---------+
| LAN | label | f4:*:66 |
| WAN | label + 11 | f4:*:71 |
| 2g | label + 2 | f4:*:68 |
| 5g | label + 3 | f4:*:69 |
+-----+------------+---------+
The label MAC address was found in Factory, 0x21000
cfgtool.py
----------
A tool for decoding and encoding Sercomm configs.
Link: https://github.com/r3d5ky/sercomm_cfg_unpacker
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Kristian Skramstad [Tue, 28 Nov 2023 08:08:58 +0000 (09:08 +0100)]
qca-nss-dp: fix typo in 0002-edma_tx_rx-support-newe
Might be a typo in drv->txtstamp function:
+ phy_rxtstamp(ndev->phydev, skb, 0);
to
+ phy_txtstamp(ndev->phydev, skb, 0);
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Florian Eckert [Mon, 7 Aug 2023 09:15:28 +0000 (11:15 +0200)]
tools: add tmon package
Add the 'tmon' packages. This is as a tool to help visualize,
tune, and test the complex thermal subsystem.
We get a compile warning for the tool that the printf format does not
fit. This commit contains a patch that fixes this warning. This patch
has also been sent upstream to the Linux kernel [1].
Links:
[1] https://lore.kernel.org/all/
20231204141335.
2798194-1-fe@dev.tdt.de/
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Felix Fietkau [Tue, 5 Dec 2023 12:06:17 +0000 (13:06 +0100)]
netifd: update to Git HEAD (2023-12-05)
02bc2e14d1d3 udebug: use helper code for ubus config handling
1b967334189b netifd: add netlink udebug ring
061e308f9f7d debug: remove newline from debug messages
f1763852dfba bridge: fix reload on bridge vlan changes
cc9e928f0a12 bridge: rework config change pvid handling
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Tue, 5 Dec 2023 11:59:49 +0000 (12:59 +0100)]
libnl-tiny: update to Git HEAD (2023-12-05)
af57bb123f93 socket: add debug callbacks for rx/tx
785e11aee7dd socket: call rx debug callback once per packet instead of per batch
965c4bf49658 socket: change debug callbacks to pass struct nl_msg
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Tue, 5 Dec 2023 09:34:55 +0000 (10:34 +0100)]
udebug: update to Git HEAD (2023-12-05)
dc24a1010d7b lib: fix handling global enable flag
c7ef98d3d3f7 lib-ucode: retry partial writes
e259bbd49cf7 lib-ucode: truncate pcap files
a296f1bac430 lib: add netlink handler function
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rafał Miłecki [Mon, 20 Nov 2023 10:46:26 +0000 (11:46 +0100)]
mediatek: filogic: add Acelink EW-7886CAX support
Acelink EW-7886CAX is an MT7986A (AKA Filogic 830) based access point.
It has 512 MiB of RAM, one 2.5 Gbps PoE (802.3at) Ethernet port and
on-SoC Wi-Fi. There is no printed MAC label (on my unit).
My unit came with Mediatek's firmware (based on OpenWrt 21.02)
installed. It was possible to simply upgrade using OpenWrt's sysupgrade
tool.
Another verified upgrade method is using U-Boot (requires UART). During
every boot there is "U-Boot Boot Menu". Selecting option "2. Upgrade
firmware" allows using U-Boot's tftp client to load and flash factory
image.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Nick Hainke [Thu, 12 Oct 2023 04:23:02 +0000 (06:23 +0200)]
libxml2: update to 2.11.6
Release Notes:
- https://gitlab.gnome.org/GNOME/libxml2/-/releases/v2.11.5
- https://gitlab.gnome.org/GNOME/libxml2/-/releases/v2.11.6
Signed-off-by: Nick Hainke <vincent@systemli.org>
Felix Fietkau [Mon, 4 Dec 2023 13:39:13 +0000 (14:39 +0100)]
libubox: update to Git HEAD (2023-12-04.1)
ca3f6d0cdb1e udebug: fix file descriptor initialization for __udebug_buf_map
Signed-off-by: Felix Fietkau <nbd@nbd.name>
David Bauer [Mon, 4 Dec 2023 12:54:56 +0000 (13:54 +0100)]
mpc85xx: allow mapping of cpu1 spin-table page
The no-map property was incorrectly added, which kept the system-memory
available on the WS-AP3825 limited to 190MB. We are allowed to map the
page containing the CPU1 spin-table, we are just not allowed to write to
it.
Fixes: 57d7382cb159 ("mpc85xx: increase available RAM on Extreme Networks WS-AP3825i")
Signed-off-by: David Bauer <mail@david-bauer.net>
Felix Fietkau [Mon, 4 Dec 2023 12:33:38 +0000 (13:33 +0100)]
libubox: update to Git HEAD (2023-12-04)
d27acfe416d6 udebug: add more checks for uninitialized buffers
df5b7147f47a udebug: add mips specific quirk
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Nick Hainke [Sat, 11 Nov 2023 09:42:12 +0000 (10:42 +0100)]
valgrind: update to 3.22.0
Release Notes:
https://sourceware.org/git/?p=valgrind.git;a=blob;f=NEWS;h=
f11da4be88687b8768268953253ddba13184bedf;hb=
bd4db67b1d386c352040b1d8fab82f5f3340fc59
Refresh patch:
- 30-mips_fix_soft_float.patch
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Sat, 11 Nov 2023 03:29:07 +0000 (04:29 +0100)]
tools/mold: update to 2.3.2
Release Notes:
https://github.com/rui314/mold/releases/tag/v2.3.2
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke [Sat, 11 Nov 2023 07:54:17 +0000 (08:54 +0100)]
tools/xz: update to 5.4.5
* liblzma:
- Use __attribute__((__no_sanitize_address__)) to avoid address
sanitization with CRC64 CLMUL. It uses 16-byte-aligned reads
which can extend past the bounds of the input buffer and
inherently trigger address sanitization errors. This isn't
a bug.
- Fixed an assertion failure that could be triggered by a large
unpadded_size argument. It was verified that there was no
other bug than the assertion failure.
- Fixed a bug that prevented building with Windows Vista
threading when __attribute__((__constructor__)) is not
supported.
* xz now properly handles special files such as "con" or "nul" on
Windows. Before this fix, the following wrote "foo" to the
console and deleted the input file "con_xz":
echo foo | xz > con_xz
xz --suffix=_xz --decompress con_xz
* Build systems:
- Allow builds with Windows win95 threading and small mode when
__attribute__((__constructor__)) is supported.
- Added a new line to liblzma.pc for MSYS2 (Windows):
Cflags.private: -DLZMA_API_STATIC
When compiling code that will link against static liblzma,
the LZMA_API_STATIC macro needs to be defined on Windows.
- CMake specific changes:
* Fixed a bug that allowed CLOCK_MONOTONIC to be used even
if the check for it failed.
* Fixed a bug where configuring CMake multiple times
resulted in HAVE_CLOCK_GETTIME and HAVE_CLOCK_MONOTONIC
not being set.
* Fixed the build with MinGW-w64-based Clang/LLVM 17.
llvm-windres now has more accurate GNU windres emulation
so the GNU windres workaround from 5.4.1 is needed with
llvm-windres version 17 too.
* The import library on Windows is now properly named
"liblzma.dll.a" instead of "libliblzma.dll.a"
* Fixed a bug causing the Ninja Generator to fail on
UNIX-like systems. This bug was introduced in 5.4.0.
* Added a new option to disable CLMUL CRC64.
* A module-definition (.def) file is now created when
building liblzma.dll with MinGW-w64.
* The pkg-config liblzma.pc file is now installed on all
builds except when using MSVC on Windows.
* Added large file support by default for platforms that
need it to handle files larger than 2 GiB. This includes
MinGW-w64, even 64-bit builds.
* Small fixes and improvements to the tests.
* Updated translations: Chinese (simplified) and Esperanto.
Signed-off-by: Nick Hainke <vincent@systemli.org>
John Audia [Sun, 3 Dec 2023 13:56:31 +0000 (08:56 -0500)]
kernel: bump 6.1 to 6.1.65
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.65
All patches automatically rebased.
Build system: x86/64
Build-tested: x86/64/AMD Cezanne, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: x86/64/AMD Cezanne, filogic/xiaomi_redmi-router-ax6000-ubootmod
Signed-off-by: John Audia <therealgraysky@proton.me>
John Audia [Sun, 3 Dec 2023 13:57:01 +0000 (08:57 -0500)]
kernel: bump 5.15 to 5.15.141
Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.141
All patches automatically rebased.
Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3
Signed-off-by: John Audia <therealgraysky@proton.me>
David Bauer [Sun, 3 Dec 2023 07:03:57 +0000 (08:03 +0100)]
mpc85xx: increase available RAM on Extreme Networks WS-AP3825i
The system-mamory size was page-aligned prior to this commit, only
enabling to use 192MB of system memory of the 256 available.
This was due to the system-memory being manually shrinked to reserve the
upper 1MB for the second-core bootpage in the loader as well as the OS.
Fix this properly in the loader and in Linux using reserved-memory
definitions. This enables the device to use 250MB of system memory.
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Sun, 3 Dec 2023 05:49:40 +0000 (06:49 +0100)]
uboot-envtools: fix GL-MT2500 offset
The previous offsets did also work, as they've wrapped back to 0x0.
However, in reality the environment starts at offset 0x0 of the
u-boot-env MMC partition.
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Sun, 3 Dec 2023 05:55:10 +0000 (06:55 +0100)]
mediatek: remove wireless packages for GL-MT2500
This device does not have wireless hardware, thus we don't need to ship
neither hostapd nor wireless drivers.
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Tue, 28 Nov 2023 00:03:48 +0000 (01:03 +0100)]
mediatek: make GL-MT2500 image work with U-Boot recovery
Append metadata in the special GL.iNet format.
This also enables use of the web-based U-Boot recovery.
U-Boot-Recovery
===============
The GL-MT2500 provides web-based U-Boot recovery. For this, hold the
reset button pressed for 5 seconds when attaching power to the device.
The LED will blink 5 times. Release the reset button.
The OpenWrt sysupgrade image can be installed by navigating to
http://192.168.1.1 in a web-browser.
The device does not work as a DHCP server, so manual IP configuration is
required.
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Mon, 27 Nov 2023 23:55:18 +0000 (00:55 +0100)]
mediatek: remove kernel build-directives for GL-MT2500
The build-directives for the GL-MT2500 are not required, as the default
ones produce working images.
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Mon, 27 Nov 2023 23:55:00 +0000 (00:55 +0100)]
mediatek: add missing eMMC packages for GL-MT2500
Signed-off-by: David Bauer <mail@david-bauer.net>
Rosen Penev [Thu, 30 Nov 2023 22:15:11 +0000 (14:15 -0800)]
mpc85xx: fix some dtc warnings
Mostly missing/wrong addresses.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Marty Jones [Tue, 28 Nov 2023 18:27:18 +0000 (13:27 -0500)]
kernel: backport fixes for realtek r8152
Fixes issues with RTL8156 2.5G USB adapters
- # ethtool eth1
Settings for eth1:
Supported ports: [ ]
Supported link modes: Not reported
Supported pause frame use: No
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 2500Mb/s
Duplex: Half
Port: Twisted Pair
PHYAD: 0
Transceiver: internal
Auto-negotiation: off
MDI-X: Unknown
Current message level: 0x00000007 (7)
drv probe link
Link detected: yes
- #
- r8152: break the loop when the budget is exhausted
- r8152: Block future register access if register access fails
- r8152: Rename RTL8152_UNPLUG to RTL8152_INACCESSIBLE
- r8152: add vendor/device ID pair for D-Link DUB-E250
- r8152: try to use a normal budget
- r8152: set bp in bulk
- r8152: adjust generic_ocp_write function
- r8152: fix the autosuspend doesn't work
- r8152: Add __GFP_NOWARN to big allocations
- r8152: reduce the control transfer of rtl8152_get_version()
- r8152: remove rtl_vendor_mode function
- r8152: avoid to change cfg for all devices
- r8152: add USB device driver for config selection
- r8152: use napi_gro_frags
- cdc_ether: no need to blacklist any r8152 devices
- cdc_ether: add u-blox 0x1313 composition
Build system: x86_64
Build-tested: bcm2711, rockchip, x86/64
Run-tested: bcm2711/RPi4B, rockchip/nanopi r2s, x86/64
Signed-off-by: Marty Jones <mj8263788@gmail.com>
Chen Minqiang [Mon, 27 Nov 2023 03:30:53 +0000 (11:30 +0800)]
mediatek: filogic: Update bootcount init script permissions
Change permissions of the bootcount init script from old mode 100644
to new mode 100755 to ensure its executability.
Fixes: 6cc14bf66aa9 ("filogic: support Telenor branded ZyXEL EX5700")
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Christian Lamparter [Fri, 1 Dec 2023 20:38:40 +0000 (21:38 +0100)]
ipq40xx: update ASUS RT-AC58U leds DTS nodes
- use color, function, function-enumerator properties.
- removes the label properties from LED nodes.
- add panic-indicator to the blue power/status LED.
Note: yes this brings the combined LAN/"switch" LED sort of back,
though I fully admit, it's a bit jank. Do you know a better option?
then please tell/make a PR!
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Christian Lamparter [Fri, 1 Dec 2023 20:20:47 +0000 (21:20 +0100)]
ipq40xx: enable CONFIG_LED_TRIGGER_PHY for AC42U
The AC42U already had PHY Triggers in the DTS.
We are probably going to use them at some point.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Shiji Yang [Tue, 31 Oct 2023 10:47:49 +0000 (18:47 +0800)]
base-files: support parse DT LED color and function
The 'label' property in led node has been deprecated and we'd better
to avoid using it. This patch allows us to extract DT OF LED name
from the newly introduced LED properties "color", "function" and
"function-enumerator".
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Shiji Yang [Tue, 31 Oct 2023 10:21:37 +0000 (18:21 +0800)]
generic: add more DT LED color and function definitions
Openwrt supports hundreds of devices. These newly added LED colors
and functions can help developers better describe LED indicators.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Russell Senior [Fri, 1 Dec 2023 21:48:56 +0000 (13:48 -0800)]
qoriq: pad rootfs with zeros
Presently, sysupgrade -n does *not* reset the overlayfs, retaining
unwanted filesystem contents. Adding PADDING=1 in front of
gen_image_generic.sh in image/Makefile ensures that the overlayfs is
recreated on firstboot.
Fixes: 080a769b4da8 ("qoriq: new target")
Signed-off-by: Russell Senior <russell@personaltelco.net>
[add Fixes tag, rewrite commit subject and message to respect line
length]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Russell Senior [Fri, 1 Dec 2023 21:48:55 +0000 (13:48 -0800)]
qoriq: set compat_version in board.d
Currently, sysupgrade without the -n option complains:
# sysupgrade -v tmp/openwrt-qoriq-generic-watchguard_firebox-m300-squashfs-sysupgrade.img.gz
upgrade: The device is supported, but the config is incompatible to the new image (1.0->1.1). Please upgrade without keeping config (sysupgrade -n).
upgrade: Kernel switched to FIT uImage. Update U-Boot environment.
upgrade: Reading partition table from bootdisk...
upgrade: Extract boot sector from the image
upgrade: Reading partition table from image...
Image check failed.
So, add the missing 05_compat-version to /etc/board.d/ to allow
sysupgrade to save config without using -f.
Fixes: c4b499bc03ab ("qoriq: use FIT uImage for Firebox M300 kernel")
Signed-off-by: Russell Senior <russell@personaltelco.net>
[drop invalid copyright header, add SPDX license header, shorten commit
subject, add fixes tag]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Hauke Mehrtens [Sun, 26 Nov 2023 22:59:54 +0000 (23:59 +0100)]
x86: Add kmod-dwmac-intel
This adds the Intel Ethernet driver for the Intel Quark/EHL/TGL chips.
Fixes: #13994
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sun, 26 Nov 2023 22:53:35 +0000 (23:53 +0100)]
armsr: Move kmod-stmmac-core to common place
Move the kmod-stmmac-core package to the common place to share it with
x86 later.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Stefan Kalscheuer [Thu, 30 Nov 2023 08:30:56 +0000 (09:30 +0100)]
mwlwifi: update to version 10.4.10-
20231129
Remove upstreamed patches:
* replace usage of the deprecated "pci-dma-compat.h" API (
6c03b27)
* remove uaccess and get_fs calls from PCIe for Kenel >= 5.18 (
1d0d08c)
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
Tony Ambardar [Fri, 24 Nov 2023 01:51:38 +0000 (17:51 -0800)]
bpftool: Update to v7.3.0
Update to the latest upstream release to include recent improvements and
bugfixes. Also refresh local patches.
Link: https://github.com/libbpf/bpftool/releases/tag/v7.3.0
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Tony Ambardar [Fri, 24 Nov 2023 01:50:10 +0000 (17:50 -0800)]
libbpf: Update to v1.3.0
Update to the latest upstream release to include recent improvements and
bugfixes. Also refresh local patches.
Link: https://github.com/libbpf/libbpf/releases/tag/v1.3.0
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Felix Fietkau [Thu, 30 Nov 2023 19:08:21 +0000 (20:08 +0100)]
hostapd: use new udebug ubus api to make debug rings configurable
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Thu, 30 Nov 2023 18:13:35 +0000 (19:13 +0100)]
ucode: update to Git HEAD (2023-11-30)
96f74b5be829 ubus: make ubus_context first in uc_ubus_connection_t
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Tue, 28 Nov 2023 14:10:57 +0000 (15:10 +0100)]
udebug: add more entries for the default config
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Thu, 30 Nov 2023 18:19:01 +0000 (19:19 +0100)]
procd: update to Git HEAD (2023-11-28)
d852f877920b service: Fix retriggering of init.d-scripts.
7e6c6efd6fbc udebug: add support for logging via udebug
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Thu, 30 Nov 2023 12:42:50 +0000 (13:42 +0100)]
ubox: update to Git HEAD (2023-11-30)
cc34fb7b922f logd: add support for subscribing to the log object
c08709cceb55 logd: add udebug support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Thu, 30 Nov 2023 11:53:29 +0000 (12:53 +0100)]
libubox: update to Git HEAD (2023-11-30)
325fea5c57cf udebug: add functions for manipulating entry length
e84c000c4756 udebug: add inline helper function to test if a buffer is allocated
40acbe34632b udebug: wait for response after buffer add/remove
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Thu, 30 Nov 2023 11:52:08 +0000 (12:52 +0100)]
udebug: update to Git HEAD (2023-11-30)
d49aadabb7a1 lib: fix dealing with udebugd restarts
9ec5fbb6aaad ubus: report ring size and data size via ubus api
86b4396baa44 ring: add debug messages for ring alloc errors
e02306af7c50 lib: add helper function for applying ring config
b613879cb049 client: send confirmation messages for ring add/remove
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Luis Mita [Wed, 22 Nov 2023 19:13:04 +0000 (15:13 -0400)]
mediatek: add support for Confiabits MT7981
Confiabits MT7981 is a Wi-Fi 6 router based on MediaTek MT7981.
Specification:
- SoC: MediaTek MT7981B
- CPU: 2x 1.3 GHz Cortex-A53
- Flash: 128 MiB SPI NAND
- RAM: 256 MiB
- WLAN: 2.4 GHz, 5 GHz (MediaTek MT7976CN, 802.11ax)
- Ethernet: 4x 10/100/1000 Mbps MT7531AE (3xLAN, 1xWAN)
- USB 2.0 port
- Buttons: 1 Reset button, 1 Mesh button.
- LEDs: 7x light-blue, 2x warm-white
- Serial console: internal 4-pin header, 115200 8n1
- Power: 12 VDC, 1.5 A
MAC addresses in stock firmware and in this commit:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| WAN | 00:0c:43:xx:xx:e1 | label+1 |
| LAN | 00:0c:43:xx:xx:e0 | label |
| WLAN 2g | 00:0c:43:xx:xx:e0 | label |
| WLAN 5g | 02:0c:43:xx:xx:e0 | |
+---------+-------------------+-----------+
The label MAC was found in 'Factory', 0x4
Installation:
The stock firmware is OpenWrt-based. If you can reach LuCI or SSH, just use the sysupgrade image
with the 'Keep settings' option turned off.
Signed-off-by: Luis Mita <luis@luismita.com>
Hauke Mehrtens [Sun, 26 Nov 2023 22:04:04 +0000 (23:04 +0100)]
target: Make TARGET_SERIAL independent of GRUB configuration
GRUB_SERIAL is also used for the default serial on the target and not
only in grub. When no grub was build it was not available and the build
fails.
Rename GRUB_SERIAL to TARGET_SERIAL and make it always available on x86
and armsr targets.
Fixes: #14063
Fixes: b10768476f9d ("x86,armsr: interpolate GRUB_SERIAL into /etc/inittab")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
John Audia [Tue, 28 Nov 2023 22:08:16 +0000 (17:08 -0500)]
kernel: bump 5.15 to 5.15.140
Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.140
Removed upstreamed:
mvebu/patches-5.15/106-Revert-i2c-pxa-move-to-generic-GPIO-recovery.patch[1]
All other patches automatically rebased.
1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.140&id=
06d320ca170b4e59bb261e2ce3ffe84e9154d42b
Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3
Signed-off-by: John Audia <therealgraysky@proton.me>
John Audia [Tue, 28 Nov 2023 19:34:53 +0000 (14:34 -0500)]
kernel: bump 6.1 to 6.1.64
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.64
Removed upstreamed:
ixp4xx/patches-6.1/0001-mtd-cfi_cmdset_0001-Byte-swap-OTP-info.patch[1]
mvebu/patches-6.1/106-Revert-i2c-pxa-move-to-generic-GPIO-recovery.patch[2]
qualcommax/patches-6.1/0026-v6.7-clk-qcom-ipq8074-drop-the-CLK_SET_RATE_PARENT-flag-f.patch[3]
Manually rebased:
bcm27xx/patches-6.1/950-0111-MMC-added-alternative-MMC-driver.patch
All other patches automatically rebased.
1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.64&id=
3b93096d29c5b9ca2af94be4ee9949c1767acf17
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.64&id=
b3fd9db79e30d5eb5f76ef1f5b7e4f444af574ea
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.64&id=
877080a3490102da26b8d969588159b2385f739e
Build system: x86/64
Build-tested: x86/64/AMD Cezanne
Run-tested: x86/64/AMD Cezanne
Signed-off-by: John Audia <therealgraysky@proton.me>
Daniel Golle [Wed, 29 Nov 2023 21:10:37 +0000 (21:10 +0000)]
mediatek: add kmod-usb3 to default package set of the ZBT-Z8102AX
Include XHCI USB drivers on the ZBT-Z8102AX router, the drivers are
required to be able to use the USB-connected M.2 slots for 4G/5G modems.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Felix Fietkau [Tue, 28 Nov 2023 21:12:15 +0000 (22:12 +0100)]
libubox: update to Git HEAD (2023-11-28)
b77f2a4ce903 uloop: fix build using C++ compilers
260ad5bd1566 udebug: add ulog support
e80dc00ee90c link librt if needed for shm_open
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Tue, 28 Nov 2023 12:54:19 +0000 (13:54 +0100)]
ubus: update to Git HEAD (2023-11-28)
2b39a27d8bcc libubus: fix reconnect with auto subscribe
f84eb5998c6e libubus: fix initial subscribe with autosubscribe
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Tue, 28 Nov 2023 11:51:37 +0000 (12:51 +0100)]
ubox: add acl file for logd
Fixes ubus reconnect, since the process user id changes to 'logd'
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Mon, 27 Nov 2023 18:36:33 +0000 (19:36 +0100)]
udebug: move ubus dependency to libudebug
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Mon, 27 Nov 2023 17:37:55 +0000 (18:37 +0100)]
udebug: update to Git HEAD (2023-11-27)
a2301fa3b0c6 README: add wireshark info
cfd83ccc1e4e server: properly handle unclaimed file descriptors
cb71f64de0ec lib: remove leftover debug code
a92101631c0d lib: fix avl tree lookup
d4b99820afd0 lib: move library code to libubox, add ubus config handling code
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Mon, 27 Nov 2023 17:37:33 +0000 (18:37 +0100)]
libubox: update to Git HEAD (2023-11-27)
82fa6480de7a uloop: add support for interval timers
13d9b04fb09d uloop: add support for user defined signal handlers
f7d156911311 uloop: properly initialize signal handler mask
8a5a4319a85c uloop: fix typo in signal handling rework
b3fa3d92e3eb uloop: reset flags after __uloop_fd_delete call
d4c3066e7c5e udebug: add udebug library code
Signed-off-by: Felix Fietkau <nbd@nbd.name>
David Bauer [Mon, 20 Nov 2023 15:36:43 +0000 (16:36 +0100)]
mediatek: copy config for Acer Predator W6
Config was previously not copied on sysupgrade.
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Thu, 20 Apr 2023 17:49:55 +0000 (19:49 +0200)]
mediatek: add support for GL.iNet GL-MT2500
Hardware
--------
SoC: MediaTek MT7981BA
RAM: 1GB DDR4 (NANYA NT5AD512M16C4-JR)
MMC: 8GB eMMC (Samsung 8GTF4R)
ETH: 1000Base-T LAN (ePHY)
2500Base-T WAN (MaxLinear GPY211C)
BTN: 1x Reset Button
LED: System (blue/white)
VPN (white)
USB: 1x USB-A (USB 3.0)
UART: 115200 8N1 - Pinout on board next to LAN port
Don't connect 3.3V!
Known Issues
------------
U-Boot vendor recovery does not seem to accept any images, neither
GL.iNet images nor OpenWrt images. Recovery requires serial access!
Installation
------------
Upload the OpenWrt sysupgrade image to the Gl.iNet Web-UI. Make sure to
not retain existing settings.
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Tue, 21 Nov 2023 13:10:09 +0000 (14:10 +0100)]
rockchip: require image metadata
All devices in the rockchip target have appended image-metadata. Enforce
the presence of this metadata to avoid flashing incomplete images.
This is the de-facto standard for almost all OpenWrt targets.
Signed-off-by: David Bauer <mail@david-bauer.net>
Lech Perczak [Thu, 16 Nov 2023 16:30:11 +0000 (17:30 +0100)]
ath79: fortinet-fap-221-b: convert to nvmem-layout
Now that MAC address parser supports the hex format (without
delimiters), use the canonical MAC address stored in U-boot partition.
Get rid of the userspace adjustments which are no longer necessary.
While at that, move the mac-base to the common part, as it is again
exactly the same in both models.
And convert ART partition too - keep that one separate, as calibration
data length differs between the models.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Lech Perczak [Thu, 16 Nov 2023 16:17:32 +0000 (17:17 +0100)]
ath79: fortinet-fap-220-b: convert to nvmem-layout
Now that MAC address parser supports the hex format (without
delimiters), use the canonical MAC address stored in U-boot partition.
Get rid of the "mac-address-increment" binding.
While at that, convert ART partition too.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Lech Perczak [Sat, 25 Nov 2023 02:09:30 +0000 (03:09 +0100)]
ath79: fortinet-fap-220-b: fix WLAN MAC addresses
Addresses were swapped compared to the factory firmware. In addition to
that, one of them was shifted by -1. Fix that by setting wlan0 MAC
offset to 9, and wlan1 MAC offset to 2.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Hauke Mehrtens [Sun, 26 Nov 2023 19:37:01 +0000 (20:37 +0100)]
ustream-ssl: update to Git HEAD (2023-11-26)
91666a3 ustream-mbedtls: Add compatibility with Mbed TLS 3.0.0
263b9a9 cmake: Fail if undefined symbols are used
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Xiaojun Liu [Mon, 13 Nov 2023 03:59:45 +0000 (03:59 +0000)]
x86 64: Add new device Cordoba Edge Platform
Add new device Cordoba Edge Platform
hardware specifications: CPU - Intel Atom C3000
Ethernet - 2 10Gbps ixgbe SPF+
2 1Gbps ixgbe RJ45/SPF
4 2.5Gbps igc RJ45
WiFi - mt7915e
LED - 3 multicolor(red|blue|green) LEDs
Signed-off-by: Xiaojun Liu <xiaojun.liu@silicom.co.il>
projects / openwrt / staging / robimarko.git / log