Dave Stevenson [Mon, 25 Jun 2018 14:07:15 +0000 (15:07 +0100)]
net: lan78xx: Use s/w csum check on VLANs without tag stripping
Observations of VLANs dropping packets due to invalid
checksums when not offloading VLAN tag receive.
With VLAN tag stripping enabled no issue is observed.
Drop back to s/w checksums if VLAN offload is disabled.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dave Stevenson [Mon, 25 Jun 2018 14:07:14 +0000 (15:07 +0100)]
net: lan78xx: Add support for VLAN tag stripping.
The chip supports stripping the VLAN tag and reporting it
in metadata.
Complete the support for this.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dave Stevenson [Mon, 25 Jun 2018 14:07:13 +0000 (15:07 +0100)]
net: lan78xx: Add support for VLAN filtering.
HW_VLAN_CTAG_FILTER was partially implemented, but not advertised
to Linux.
Complete the implementation of this.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dave Stevenson [Mon, 25 Jun 2018 14:07:12 +0000 (15:07 +0100)]
net: lan78xx: Allow for VLAN headers in timeout calcs
The frame abort timeout being set by lan78xx_set_rx_max_frame_length
didn't account for any VLAN headers, resulting in very low
throughput if used with tagged VLANs.
Use VLAN_ETH_HLEN instead of ETH_HLEN to correct for this.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Slaby [Mon, 25 Jun 2018 07:26:27 +0000 (09:26 +0200)]
r8152: napi hangup fix after disconnect
When unplugging an r8152 adapter while the interface is UP, the NIC
becomes unusable. usb->disconnect (aka rtl8152_disconnect) deletes
napi. Then, rtl8152_disconnect calls unregister_netdev and that invokes
netdev->ndo_stop (aka rtl8152_close). rtl8152_close tries to
napi_disable, but the napi is already deleted by disconnect above. So
the first while loop in napi_disable never finishes. This results in
complete deadlock of the network layer as there is rtnl_mutex held by
unregister_netdev.
So avoid the call to napi_disable in rtl8152_close when the device is
already gone.
The other calls to usb_kill_urb, cancel_delayed_work_sync,
netif_stop_queue etc. seem to be fine. The urb and netdev is not
destroyed yet.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: linux-usb@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 25 Jun 2018 07:58:17 +0000 (15:58 +0800)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Fix netpoll OOPS in r8169, from Ville Syrjälä.
2) Fix bpf instruction alignment on powerpc et al., from Eric Dumazet.
3) Don't ignore IFLA_MTU attribute when creating new ipvlan links. From
Xin Long.
4) Fix use after free in AF_PACKET, from Eric Dumazet.
5) Mis-matched RTNL unlock in xen-netfront, from Ross Lagerwall.
6) Fix VSOCK loopback on big-endian, from Claudio Imbrenda.
7) Missing RX buffer offset correction when computing DMA addresses in
mvneta driver, from Antoine Tenart.
8) Fix crashes in DCCP's ccid3_hc_rx_send_feedback, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (34 commits)
sfc: make function efx_rps_hash_bucket static
strparser: Corrected typo in documentation.
qmi_wwan: add support for the Dell Wireless 5821e module
cxgb4: when disabling dcb set txq dcb priority to 0
net_sched: remove a bogus warning in hfsc
net: dccp: switch rx_tstamp_last_feedback to monotonic clock
net: dccp: avoid crash in ccid3_hc_rx_send_feedback()
net: Remove depends on HAS_DMA in case of platform dependency
MAINTAINERS: Add file patterns for dsa device tree bindings
net: mscc: make sparse happy
net: mvneta: fix the Rx desc DMA address in the Rx path
Documentation: e1000: Fix docs build error
Documentation: e100: Fix docs build error
Documentation: e1000: Use correct heading adornment
Documentation: e100: Use correct heading adornment
ipv6: mcast: fix unsolicited report interval after receiving querys
vhost_net: validate sock before trying to put its fd
VSOCK: fix loopback on big-endian systems
net: ethernet: ti: davinci_cpdma: make function cpdma_desc_pool_create static
xen-netfront: Update features after registering netdev
...
Colin Ian King [Sun, 24 Jun 2018 10:57:31 +0000 (11:57 +0100)]
sfc: make function efx_rps_hash_bucket static
The function efx_rps_hash_bucket is local to the source and
does not need to be in global scope, so make it static.
Cleans up sparse warning:
symbol 'efx_rps_hash_bucket' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 24 Jun 2018 12:54:29 +0000 (20:54 +0800)]
Linux 4.18-rc2
Linus Torvalds [Sun, 24 Jun 2018 12:29:15 +0000 (20:29 +0800)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf fixes from Thomas Gleixner:
"A pile of perf updates:
Kernel side:
- Remove an incorrect warning in uprobe_init_insn() when
insn_get_length() fails. The error return code is handled at the
call site.
- Move the inline keyword to the right place in the perf ringbuffer
code to address a W=1 build warning.
Tooling:
perf stat:
- Fix metric column header display alignment
- Improve error messages for default attributes, providing better
output for error in command line.
- Add --interval-clear option, to provide a 'watch' like printing
perf script:
- Show hw-cache events too
perf c2c:
- Fix data dependency problem in layout of 'struct c2c_hist_entry'
Core:
- Do not blindly assume that 'struct perf_evsel' can be obtained via
a straight forward container_of() as there are call sites which
hand in a plain 'struct hist' which is not part of a container.
- Fix error index in the PMU event parser, so that error messages can
point to the problematic token"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Move the inline keyword at the beginning of the function declaration
uprobes/x86: Remove incorrect WARN_ON() in uprobe_init_insn()
perf script: Show hw-cache events
perf c2c: Keep struct hist_entry at the end of struct c2c_hist_entry
perf stat: Add event parsing error handling to add_default_attributes
perf stat: Allow to specify specific metric column len
perf stat: Fix metric column header display alignment
perf stat: Use only color_fprintf call in print_metric_only
perf stat: Add --interval-clear option
perf tools: Fix error index for pmu event parser
perf hists: Reimplement hists__has_callchains()
perf hists browser gtk: Use hist_entry__has_callchains()
perf hists: Make hist_entry__has_callchains() work with 'perf c2c'
perf hists: Save the callchain_size in struct hist_entry
Linus Torvalds [Sun, 24 Jun 2018 12:18:19 +0000 (20:18 +0800)]
Merge branch 'sched-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull rseq fixes from Thomas Gleixer:
"A pile of rseq related fixups:
- Prevent infinite recursion when delivering SIGSEGV
- Remove the abort of rseq critical section on fork() as syscalls
inside rseq critical sections are explicitely forbidden. So no
point in doing the abort on the child.
- Align the rseq structure on 32 bytes in the ARM selftest code.
- Fix file permissions of the test script"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rseq: Avoid infinite recursion when delivering SIGSEGV
rseq/cleanup: Do not abort rseq c.s. in child on fork()
rseq/selftests/arm: Align 'struct rseq_cs' on 32 bytes
rseq/selftests: Make run_param_test.sh executable
Linus Torvalds [Sun, 24 Jun 2018 12:16:17 +0000 (20:16 +0800)]
Merge branch 'efi-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull EFI fixes from Thomas Gleixner:
"Two fixlets for the EFI maze:
- Properly zero variables to prevent an early boot hang on EFI mixed
mode systems
- Fix the fallout of merging the 32bit and 64bit variants of EFI PCI
related code which ended up chosing the 32bit variant of the actual
EFi call invocation which leads to failures on 64bit"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/x86: Fix incorrect invocation of PciIo->Attributes()
efi/libstub/tpm: Initialize efi_physical_addr_t vars to zero for mixed mode
Linus Torvalds [Sun, 24 Jun 2018 12:06:42 +0000 (20:06 +0800)]
Merge branch 'core-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull core fixes from Thomas Gleixner:
"Two tiny fixes:
- Add the missing machine_real_restart() to objtools noreturn list so
it stops complaining
- Fix a trivial comment typo"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
kernel.h: Fix a typo in comment
objtool: Add machine_real_restart() to the noreturn list
Linus Torvalds [Sun, 24 Jun 2018 11:59:52 +0000 (19:59 +0800)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A set of fixes for x86:
- Make Xen PV guest deal with speculative store bypass correctly
- Address more fallout from the 5-Level pagetable handling. Undo an
__initdata annotation to avoid section mismatch and malfunction
when post init code would touch the freed variable.
- Handle exception fixup in math_error() before calling notify_die().
The reverse call order incorrectly triggers notify_die() listeners
for soemthing which is handled correctly at the site which issues
the floating point instruction.
- Fix an off by one in the LLC topology calculation on AMD
- Handle non standard memory block sizes gracefully un UV platforms
- Plug a memory leak in the microcode loader
- Sanitize the purgatory build magic
- Add the x86 specific device tree bindings directory to the x86
MAINTAINER file patterns"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Fix 'no5lvl' handling
Revert "x86/mm: Mark __pgtable_l5_enabled __initdata"
x86/CPU/AMD: Fix LLC ID bit-shift calculation
MAINTAINERS: Add file patterns for x86 device tree bindings
x86/microcode/intel: Fix memleak in save_microcode_patch()
x86/platform/UV: Add kernel parameter to set memory block size
x86/platform/UV: Use new set memory block size function
x86/platform/UV: Add adjustable set memory block size function
x86/build: Remove unnecessary preparation for purgatory
Revert "kexec/purgatory: Add clean-up for purgatory directory"
x86/xen: Add call of speculative_store_bypass_ht_init() to PV paths
x86: Call fixup_exception() before notify_die() in math_error()
Linus Torvalds [Sun, 24 Jun 2018 11:48:30 +0000 (19:48 +0800)]
Merge branch 'x86-pti-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 pti fixes from Thomas Gleixner:
"Two small updates for the speculative distractions:
- Make it more clear to the compiler that array_index_mask_nospec()
is not subject for optimizations. It's not perfect, but ...
- Don't report XEN PV guests as vulnerable because their mitigation
state depends on the hypervisor. Report unknown and refer to the
hypervisor requirement"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/spectre_v1: Disable compiler optimizations over array_index_mask_nospec()
x86/pti: Don't report XenPV as vulnerable
Linus Torvalds [Sun, 24 Jun 2018 11:36:16 +0000 (19:36 +0800)]
Merge branch 'locking-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull locking fixes from Thomas Gleixner:
"A set of fixes and updates for the locking code:
- Prevent lockdep from updating irq state within its own code and
thereby confusing itself.
- Buid fix for older GCCs which mistreat anonymous unions
- Add a missing lockdep annotation in down_read_non_onwer() which
causes up_read_non_owner() to emit a lockdep splat
- Remove the custom alpha dec_and_lock() implementation which is
incorrect in terms of ordering and use the generic one.
The remaining two commits are not strictly fixes. They provide irqsave
variants of atomic_dec_and_lock() and refcount_dec_and_lock(). These
are required to merge the relevant updates and cleanups into different
maintainer trees for 4.19, so routing them into mainline without
actual users is the sanest approach.
They should have been in -rc1, but last weekend I took the liberty to
just avoid computers in order to regain some mental sanity"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/qspinlock: Fix build for anonymous union in older GCC compilers
locking/lockdep: Do not record IRQ state within lockdep code
locking/rwsem: Fix up_read_non_owner() warning with DEBUG_RWSEMS
locking/refcounts: Implement refcount_dec_and_lock_irqsave()
atomic: Add irqsave variant of atomic_dec_and_lock()
alpha: Remove custom dec_and_lock() implementation
Linus Torvalds [Sun, 24 Jun 2018 11:22:19 +0000 (19:22 +0800)]
Merge branch 'ras-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull ras fixes from Thomas Gleixner:
"A set of fixes for RAS/MCE:
- Improve the error message when the kernel cannot recover from a MCE
so the maximum amount of information gets provided.
- Individually check MCE recovery features on SkyLake CPUs instead of
assuming none when the CAPID0 register does not advertise the
general ability for recovery.
- Prevent MCE to output inconsistent messages which first show an
error location and then claim that the source is unknown.
- Prevent overwriting MCi_STATUS in the attempt to gather more
information when a fatal MCE has alreay been detected. This leads
to empty status values in the printout and failing to react
promptly on the fatal event"
* 'ras-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mce: Fix incorrect "Machine check from unknown source" message
x86/mce: Do not overwrite MCi_STATUS in mce_no_way_out()
x86/mce: Check for alternate indication of machine check recovery on Skylake
x86/mce: Improve error message when kernel cannot recover
Linus Torvalds [Sun, 24 Jun 2018 11:16:42 +0000 (19:16 +0800)]
Merge branch 'timers-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"A small set of fixes for time(r) related issues:
- Fix a long standing conversion issue in jiffies_to_msecs() for odd
HZ values like 1024 or 1200 which resulted in returning 0 for small
jiffies values due to rounding down.
- Use the proper CONFIG symbol in the new Y2038 safe compat code for
posix-timers. Not yet a visible breakage, but this will immediately
trigger when the architecture support for the new interfaces is
merged.
- Return an error code in the STM32 clocksource driver on failure
instead of success.
- Remove the redundant and stale irq disabled check in the posix cpu
timer code. The check is at the wrong place anyway and lockdep
already covers it via the sighand lock locking coverage"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
time: Make sure jiffies_to_msecs() preserves non-zero time periods
posix-timers: Fix nanosleep_copyout() for CONFIG_COMPAT_32BIT_TIME
clocksource/drivers/stm32: Fix error return code
posix-cpu-timers: Remove lockdep_assert_irqs_disabled()
Linus Torvalds [Sun, 24 Jun 2018 11:01:18 +0000 (19:01 +0800)]
Merge branch 'irq-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A set of fixes mostly for the ARM/GIC world:
- Fix the MSI affinity handling in the ls-scfg irq chip driver so it
updates and uses the effective affinity mask correctly
- Prevent binding LPIs to offline CPUs and respect the Cavium erratum
which requires that LPIs which belong to an offline NUMA node are
not bound to a CPU on a different NUMA node.
- Free only the amount of allocated interrupts in the GIC-V2M driver
instead of trying to free log2(nrirqs).
- Prevent emitting SYNC and VSYNC targetting non existing interrupt
collections in the GIC-V3 ITS driver
- Ensure that the GIV-V3 interrupt redistributor is correctly
reprogrammed on CPU hotplug
- Remove a stale unused helper function"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqdesc: Delete irq_desc_get_msi_desc()
irqchip/gic-v3-its: Fix reprogramming of redistributors on CPU hotplug
irqchip/gic-v3-its: Only emit VSYNC if targetting a valid collection
irqchip/gic-v3-its: Only emit SYNC if targetting a valid collection
irqchip/gic-v3-its: Don't bind LPI to unavailable NUMA node
irqchip/gic-v2m: Fix SPI release on error path
irqchip/ls-scfg-msi: Fix MSI affinity handling
genirq/debugfs: Add missing IRQCHIP_SUPPORTS_LEVEL_MSI debug
Linus Torvalds [Sun, 24 Jun 2018 09:19:42 +0000 (17:19 +0800)]
Merge tag 'mips_fixes_4.18_1' of git://git./linux/kernel/git/mips/linux
Pull MIPS fixes from Paul Burton:
"A few MIPS fixes for 4.18:
- a GPIO device name fix for a regression in v4.15-rc1.
- an errata workaround for the BCM5300X platform.
- a fix to ftrace function graph tracing, broken for a long time with
the fix applying cleanly back as far as v3.17.
- addition of read barriers to in{b,w,l,q}() functions, matching
behavior of other architectures & mirroring the equivalent addition
to read{b,w,l,q} in v4.17-rc2.
Plus changes to wire up new syscalls introduced in the 4.18 cycle:
- Restartable sequences support is added, including MIPS support in
the selftests.
- io_pgetevents is wired up"
* tag 'mips_fixes_4.18_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: Wire up io_pgetevents syscall
rseq/selftests: Implement MIPS support
MIPS: Wire up the restartable sequences (rseq) syscall
MIPS: Add syscall detection for restartable sequences
MIPS: Add support for restartable sequences
MIPS: io: Add barrier after register read in inX()
mips: ftrace: fix static function graph tracing
MIPS: BCM47XX: Enable 74K Core ExternalSync for PCIe erratum
MIPS: pb44: Fix i2c-gpio GPIO descriptor table
Vakul Garg [Sun, 24 Jun 2018 12:44:01 +0000 (18:14 +0530)]
strparser: Corrected typo in documentation.
Replaced strp_pause() with strp_unpause() to correct a seemingly copy
paste documentation mistake.
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ard Biesheuvel [Sat, 23 Jun 2018 21:19:03 +0000 (23:19 +0200)]
efi/x86: Fix incorrect invocation of PciIo->Attributes()
The following commit:
2c3625cb9fa2 ("efi/x86: Fold __setup_efi_pci32() and __setup_efi_pci64() into one function")
... merged the two versions of __setup_efi_pciXX(), without taking into
account that the 32-bit version used a rather dodgy trick to pass an
immediate 0 constant as argument for a uint64_t parameter.
The issue is caused by the fact that on x86, UEFI protocol method calls
are redirected via struct efi_config::call(), which is a variadic function,
and so the compiler has to infer the types of the parameters from the
arguments rather than from the prototype.
As the 32-bit x86 calling convention passes arguments via the stack,
passing the unqualified constant 0 twice is the same as passing 0ULL,
which is why the 32-bit code in __setup_efi_pci32() contained the
following call:
status = efi_early->call(pci->attributes, pci,
EfiPciIoAttributeOperationGet, 0, 0,
&attributes);
to invoke this UEFI protocol method:
typedef
EFI_STATUS
(EFIAPI *EFI_PCI_IO_PROTOCOL_ATTRIBUTES) (
IN EFI_PCI_IO_PROTOCOL *This,
IN EFI_PCI_IO_PROTOCOL_ATTRIBUTE_OPERATION Operation,
IN UINT64 Attributes,
OUT UINT64 *Result OPTIONAL
);
After the merge, we inadvertently ended up with this version for both
32-bit and 64-bit builds, breaking the latter.
So replace the two zeroes with the explicitly typed constant 0ULL,
which works as expected on both 32-bit and 64-bit builds.
Wilfried tested the 64-bit build, and I checked the generated assembly
of a 32-bit build with and without this patch, and they are identical.
Reported-by: Wilfried Klaebe <linux-kernel@lebenslange-mailadresse.de>
Tested-by: Wilfried Klaebe <linux-kernel@lebenslange-mailadresse.de>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: hdegoede@redhat.com
Cc: linux-efi@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Aleksander Morgado [Sat, 23 Jun 2018 21:22:52 +0000 (23:22 +0200)]
qmi_wwan: add support for the Dell Wireless 5821e module
This module exposes two USB configurations: a QMI+AT capable setup on
USB config #1 and a MBIM capable setup on USB config #2.
By default the kernel will choose the MBIM capable configuration as
long as the cdc_mbim driver is available. This patch adds support for
the QMI port in the secondary configuration.
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ganesh Goudar [Sat, 23 Jun 2018 14:58:26 +0000 (20:28 +0530)]
cxgb4: when disabling dcb set txq dcb priority to 0
When we are disabling DCB, store "0" in txq->dcb_prio
since that's used for future TX Work Request "OVLAN_IDX"
values. Setting non zero priority upon disabling DCB
would halt the traffic.
Reported-by: AMG Zollner Robert <robert@cloudmedia.eu>
CC: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 23 Jun 2018 22:33:54 +0000 (06:33 +0800)]
Merge tag 'for-linus-
20180623' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- Further timeout fixes. We aren't quite there yet, so expect another
round of fixes for that to completely close some of the IRQ vs
completion races. (Christoph/Bart)
- Set of NVMe fixes from the usual suspects, mostly error handling
- Two off-by-one fixes (Dan)
- Another bdi race fix (Jan)
- Fix nbd reconfigure with NBD_DISCONNECT_ON_CLOSE (Doron)
* tag 'for-linus-
20180623' of git://git.kernel.dk/linux-block:
blk-mq: Fix timeout handling in case the timeout handler returns BLK_EH_DONE
bdi: Fix another oops in wb_workfn()
lightnvm: Remove depends on HAS_DMA in case of platform dependency
nvme-pci: limit max IO size and segments to avoid high order allocations
nvme-pci: move nvme_kill_queues to nvme_remove_dead_ctrl
nvme-fc: release io queues to allow fast fail
nbd: Add the nbd NBD_DISCONNECT_ON_CLOSE config flag.
block: sed-opal: Fix a couple off by one bugs
blk-mq-debugfs: Off by one in blk_mq_rq_state_name()
nvmet: reset keep alive timer in controller enable
nvme-rdma: don't override opts->queue_size
nvme-rdma: Fix command completion race at error recovery
nvme-rdma: fix possible free of a non-allocated async event buffer
nvme-rdma: fix possible double free condition when failing to create a controller
Revert "block: Add warning for bi_next not NULL in bio_endio()"
block: fix timeout changes for legacy request drivers
Linus Torvalds [Sat, 23 Jun 2018 22:31:54 +0000 (06:31 +0800)]
Merge branch 'linus' of git://git./linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
- Fix use after free in chtls
- Fix RBP breakage in sha3
- Fix use after free in hwrng_unregister
- Fix overread in morus640
- Move sleep out of kernel_neon in arm64/aes-blk
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
hwrng: core - Always drop the RNG in hwrng_unregister()
crypto: morus640 - Fix out-of-bounds access
crypto: don't optimize keccakf()
crypto: arm64/aes-blk - fix and move skcipher_walk_done out of kernel_neon_begin, _end
crypto: chtls - use after free in chtls_pt_recvmsg()
Linus Torvalds [Sat, 23 Jun 2018 22:26:19 +0000 (06:26 +0800)]
Merge tag 'linux-kselftest-4.18-rc2' of git://git./linux/kernel/git/shuah/linux-kselftest
Pull kselftest fixes from Shuah Khan:
- fix new sparc64 adi driver test compile errors on non-sparc systems
- fix config fragment for sync framework for improved test coverage
- fix several tests to return correct Kselftest skip code
* tag 'linux-kselftest-4.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: sparc64: Add missing SPDX License Identifiers
selftests: sparc64: delete RUN_TESTS and EMIT_TESTS overrides
selftests: sparc64: Fix to do nothing on non-sparc64
selftests: sync: add config fragment for testing sync framework
selftests: vm: return Kselftest Skip code for skipped tests
selftests: zram: return Kselftest Skip code for skipped tests
selftests: user: return Kselftest Skip code for skipped tests
selftests: sysctl: return Kselftest Skip code for skipped tests
selftests: static_keys: return Kselftest Skip code for skipped tests
selftests: pstore: return Kselftest Skip code for skipped tests
Linus Torvalds [Sat, 23 Jun 2018 22:23:28 +0000 (06:23 +0800)]
Merge tag 'trace-v4.18-rc1' of git://git./linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"This contains a few fixes and a clean up.
- a bad merge caused an "endif" to go in the wrong place in
scripts/Makefile.build
- softirq tracing fix for tracing that corrupts lockdep and causes a
false splat
- histogram documentation typo fixes
- fix a bad memory reference when passing in no filter to the filter
code
- simplify code by using the swap macro instead of open coding the
swap"
* tag 'trace-v4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix SKIP_STACK_VALIDATION=1 build due to bad merge with -mrecord-mcount
tracing: Fix some errors in histogram documentation
tracing: Use swap macro in update_max_tr
softirq: Reorder trace_softirqs_on to prevent lockdep splat
tracing: Check for no filter when processing event filters
Bart Van Assche [Fri, 22 Jun 2018 20:18:09 +0000 (13:18 -0700)]
blk-mq: Fix timeout handling in case the timeout handler returns BLK_EH_DONE
Make sure that RQF_TIMED_OUT is cleared when a request is reused
after a block driver timeout handler has returned BLK_EH_DONE.
Fixes: da6612673988 ("blk-mq: don't time out requests again that are in the timeout handler")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jianchao Wang <jianchao.w.wang@oracle.com>
Cc: Andrew Randrianasulu <randrianasulu@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Linus Torvalds [Sat, 23 Jun 2018 13:13:05 +0000 (21:13 +0800)]
Merge tag 'powerpc-4.18-2' of git://git./linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- a fix for hugetlb with 4K pages, broken by our recent changes for
split PMD PTL.
- set the correct assembler machine type on e500mc, needed since
binutils 2.26 introduced two forms for the "wait" instruction.
- a fix for potential missed TLB flushes with MADV_[FREE|DONTNEED] etc.
and THP on Power9 Radix.
- three fixes to try and make our panic handling more robust by hard
disabling interrupts, and not marking stopped CPUs as offline because
they haven't been properly offlined.
- three other minor fixes.
Thanks to: Aneesh Kumar K.V, Michael Jeanson, Nicholas Piggin.
* tag 'powerpc-4.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mm/hash/4k: Free hugetlb page table caches correctly.
powerpc/64s/radix: Fix radix_kvm_prefetch_workaround paca access of not possible CPU
powerpc/64s: Fix build failures with CONFIG_NMI_IPI=n
powerpc/64: hard disable irqs on the panic()ing CPU
powerpc: smp_send_stop do not offline stopped CPUs
powerpc/64: hard disable irqs in panic_smp_self_stop
powerpc/64s: Fix DT CPU features Power9 DD2.1 logic
powerpc/64s/radix: Fix MADV_[FREE|DONTNEED] TLB flush miss problem with THP
powerpc/e500mc: Set assembler machine type to e500mc
Linus Torvalds [Sat, 23 Jun 2018 13:07:43 +0000 (21:07 +0800)]
Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- clear buffers allocated with FORCE_CONTIGUOUS explicitly until the
CMA code honours __GFP_ZERO
- notrace annotation for secondary_start_kernel()
- use early_param() instead of __setup() for "kpti=" as it is needed
for the cpufeature callback remapping swapper to non-global mappings
- ensure writes to swapper are ordered wrt subsequent cache maintenance
in the kpti non-global remapping code
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mm: Ensure writes to swapper are ordered wrt subsequent cache maintenance
arm64: kpti: Use early_param for kpti= command-line option
arm64: make secondary_start_kernel() notrace
arm64: dma-mapping: clear buffers allocated with FORCE_CONTIGUOUS flag
Linus Torvalds [Sat, 23 Jun 2018 12:59:00 +0000 (20:59 +0800)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull KVM fixes from Radim Krčmář:
"ARM:
- Lazy FPSIMD switching fixes
- Really disable compat ioctls on architectures that don't want it
- Disable compat on arm64 (it was never implemented...)
- Rely on architectural requirements for GICV on GICv3
- Detect bad alignments in unmap_stage2_range
x86:
- Add nested VM entry checks to avoid broken error recovery path
- Minor documentation fix"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: fix KVM_CAP_HYPERV_TLBFLUSH paragraph number
kvm: vmx: Nested VM-entry prereqs for event inj.
KVM: arm64: Prevent KVM_COMPAT from being selected
KVM: Enforce error in ioctl for compat tasks when !KVM_COMPAT
KVM: arm/arm64: add WARN_ON if size is not PAGE_SIZE aligned in unmap_stage2_range
KVM: arm64: Avoid mistaken attempts to save SVE state for vcpus
KVM: arm64/sve: Fix SVE trap restoration for non-current tasks
KVM: arm64: Don't mask softirq with IRQs disabled in vcpu_put()
arm64: Introduce sysreg_clear_set()
KVM: arm/arm64: Drop resource size check for GICV window
Linus Torvalds [Sat, 23 Jun 2018 12:44:11 +0000 (20:44 +0800)]
Merge tag 'for-linus-4.18-rc2-tag' of git://git./linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"This contains the following fixes/cleanups:
- the removal of a BUG_ON() which wasn't necessary and which could
trigger now due to a recent change
- a correction of a long standing bug happening very rarely in Xen
dom0 when a hypercall buffer from user land was not accessible by
the hypervisor for very short periods of time due to e.g. page
migration or compaction
- usage of EXPORT_SYMBOL_GPL() instead of EXPORT_SYMBOL() in a
Xen-related driver (no breakage possible as using those symbols
without others already exported via EXPORT-SYMBOL_GPL() wouldn't
make any sense)
- a simplification for Xen PVH or Xen ARM guests
- some additional error handling for callers of xenbus_printf()"
* tag 'for-linus-4.18-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: Remove unnecessary BUG_ON from __unbind_from_irq()
xen: add new hypercall buffer mapping device
xen/scsiback: add error handling for xenbus_printf
scsi: xen-scsifront: add error handling for xenbus_printf
xen/grant-table: Export gnttab_{alloc|free}_pages as GPL
xen: add error handling for xenbus_printf
xen: share start flags between PV and PVH
Kirill A. Shutemov [Fri, 22 Jun 2018 22:08:41 +0000 (01:08 +0300)]
x86/mm: Fix 'no5lvl' handling
early_identify_cpu() has to use early version of pgtable_l5_enabled()
that doesn't rely on cpu_feature_enabled().
Defining USE_EARLY_PGTABLE_L5 before all includes does the trick.
I lost the define in one of reworks of the original patch.
Fixes: 372fddf70904 ("x86/mm: Introduce the 'no5lvl' kernel parameter")
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Link: https://lkml.kernel.org/r/20180622220841.54135-3-kirill.shutemov@linux.intel.com
Kirill A. Shutemov [Fri, 22 Jun 2018 22:08:40 +0000 (01:08 +0300)]
Revert "x86/mm: Mark __pgtable_l5_enabled __initdata"
This reverts commit
e4e961e36f063484c48bed919013c106d178995d.
We need to use early version of pgtable_l5_enabled() in
early_identify_cpu() as this code runs before cpu_feature_enabled() is
usable.
But it leads to section mismatch:
cpu_init()
load_mm_ldt()
ldt_slot_va()
LDT_BASE_ADDR
LDT_PGD_ENTRY
pgtable_l5_enabled()
__pgtable_l5_enabled
__pgtable_l5_enabled marked as __initdata, but cpu_init() is not __init.
It's fixable: early code can be isolated into a separate translation unit,
but such change collides with other work in the area. That's too much
hassle to save 4 bytes of memory.
Return __pgtable_l5_enabled back to be __ro_after_init.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Link: https://lkml.kernel.org/r/20180622220841.54135-2-kirill.shutemov@linux.intel.com
Cong Wang [Fri, 22 Jun 2018 21:33:16 +0000 (14:33 -0700)]
net_sched: remove a bogus warning in hfsc
In update_vf():
cftree_remove(cl);
update_cfmin(cl->cl_parent);
the cl_cfmin of cl->cl_parent is intentionally updated to 0
when that parent only has one child. And if this parent is
root qdisc, we could end up, in hfsc_schedule_watchdog(),
that we can't decide the next schedule time for qdisc watchdog.
But it seems safe that we can just skip it, as this watchdog is
not always scheduled anyway.
Thanks to Marco for testing all the cases, nothing is broken.
Reported-by: Marco Berizzi <pupilla@libero.it>
Tested-by: Marco Berizzi <pupilla@libero.it>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 23 Jun 2018 01:46:44 +0000 (10:46 +0900)]
Merge branch 'dccp-fixes-around-rx_tstamp_last_feedback'
Eric Dumazet says:
====================
net: dccp: fixes around rx_tstamp_last_feedback
This patch series fix some issues with rx_tstamp_last_feedback.
- Switch to monotonic clock.
- Avoid potential overflows on fast hosts/networks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 22 Jun 2018 13:44:15 +0000 (06:44 -0700)]
net: dccp: switch rx_tstamp_last_feedback to monotonic clock
To compute delays, better not use time of the day which can
be changed by admins or malicious programs.
Also change ccid3_first_li() to use s64 type for delta variable
to avoid potential overflows.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Cc: dccp@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 22 Jun 2018 13:44:14 +0000 (06:44 -0700)]
net: dccp: avoid crash in ccid3_hc_rx_send_feedback()
On fast hosts or malicious bots, we trigger a DCCP_BUG() which
seems excessive.
syzbot reported :
BUG: delta (-6195) <= 0 at net/dccp/ccids/ccid3.c:628/ccid3_hc_rx_send_feedback()
CPU: 1 PID: 18 Comm: ksoftirqd/1 Not tainted 4.18.0-rc1+ #112
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1c9/0x2b4 lib/dump_stack.c:113
ccid3_hc_rx_send_feedback net/dccp/ccids/ccid3.c:628 [inline]
ccid3_hc_rx_packet_recv.cold.16+0x38/0x71 net/dccp/ccids/ccid3.c:793
ccid_hc_rx_packet_recv net/dccp/ccid.h:185 [inline]
dccp_deliver_input_to_ccids+0xf0/0x280 net/dccp/input.c:180
dccp_rcv_established+0x87/0xb0 net/dccp/input.c:378
dccp_v4_do_rcv+0x153/0x180 net/dccp/ipv4.c:654
sk_backlog_rcv include/net/sock.h:914 [inline]
__sk_receive_skb+0x3ba/0xd80 net/core/sock.c:517
dccp_v4_rcv+0x10f9/0x1f58 net/dccp/ipv4.c:875
ip_local_deliver_finish+0x2eb/0xda0 net/ipv4/ip_input.c:215
NF_HOOK include/linux/netfilter.h:287 [inline]
ip_local_deliver+0x1e9/0x750 net/ipv4/ip_input.c:256
dst_input include/net/dst.h:450 [inline]
ip_rcv_finish+0x823/0x2220 net/ipv4/ip_input.c:396
NF_HOOK include/linux/netfilter.h:287 [inline]
ip_rcv+0xa18/0x1284 net/ipv4/ip_input.c:492
__netif_receive_skb_core+0x2488/0x3680 net/core/dev.c:4628
__netif_receive_skb+0x2c/0x1e0 net/core/dev.c:4693
process_backlog+0x219/0x760 net/core/dev.c:5373
napi_poll net/core/dev.c:5771 [inline]
net_rx_action+0x7da/0x1980 net/core/dev.c:5837
__do_softirq+0x2e8/0xb17 kernel/softirq.c:284
run_ksoftirqd+0x86/0x100 kernel/softirq.c:645
smpboot_thread_fn+0x417/0x870 kernel/smpboot.c:164
kthread+0x345/0x410 kernel/kthread.c:240
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:412
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Cc: dccp@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Geert Uytterhoeven [Fri, 22 Jun 2018 11:08:43 +0000 (13:08 +0200)]
net: Remove depends on HAS_DMA in case of platform dependency
Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST".
In most cases this other symbol is an architecture or platform specific
symbol, or PCI.
Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.
This simplifies the dependencies, and allows to improve compile-testing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geert Uytterhoeven [Fri, 22 Jun 2018 10:08:13 +0000 (12:08 +0200)]
MAINTAINERS: Add file patterns for dsa device tree bindings
Submitters of device tree binding documentation may forget to CC
the subsystem maintainer if this is missing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Fri, 22 Jun 2018 09:50:52 +0000 (11:50 +0200)]
net: mscc: make sparse happy
This patch fixes a sparse warning about using an incorrect type in
argument 2 of ocelot_write_rix(), as an u32 was expected but a __be32
was given. The conversion to u32 is forced, which is safe as the value
will be written as-is in the hardware without any modification.
Fixes: 08d02364b12f ("net: mscc: fix the injection header")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Fri, 22 Jun 2018 08:15:39 +0000 (10:15 +0200)]
net: mvneta: fix the Rx desc DMA address in the Rx path
When using s/w buffer management, buffers are allocated and DMA mapped.
When doing so on an arm64 platform, an offset correction is applied on
the DMA address, before storing it in an Rx descriptor. The issue is
this DMA address is then used later in the Rx path without removing the
offset correction. Thus the DMA address is wrong, which can led to
various issues.
This patch fixes this by removing the offset correction from the DMA
address retrieved from the Rx descriptor before using it in the Rx path.
Fixes: 8d5047cf9ca2 ("net: mvneta: Convert to be 64 bits compatible")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tobin C. Harding [Fri, 22 Jun 2018 00:37:08 +0000 (10:37 +1000)]
Documentation: e1000: Fix docs build error
Recent patch updated e1000 docs to rst format. Docs build (`make
htmldocs`) is currently failing due to this file with error:
(SEVERE/4) Unexpected section title.
This is because a section of the file is indented 2 spaces. Build error
can be cleared by aligning the text with column 0. While we are changing
these lines we can make sure line length does not exceed 72, that
newlines following headings are uniform, and that full stops are
followed by two spaces.
Align text with column 0, limit line length to 72, ensure two spaces
follow all full stops, ensure uniform use of newlines after heading.
Fixes commit (
228046e76189 Documentation: e1000: Update kernel documentation)
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tobin C. Harding [Fri, 22 Jun 2018 00:37:07 +0000 (10:37 +1000)]
Documentation: e100: Fix docs build error
Recent patch updated e100 docs to rst format. Docs build (`make
htmldocs`) is currently failing due to this file with error:
(SEVERE/4) Unexpected section title.
This is because a section of the file is indented 2 spaces. Build error
can be cleared by aligning the text with column 0. While we are changing
these lines we can make sure line length does not exceed 72, that
newlines following headings are uniform, and that full stops are
followed by two spaces.
Align text with column 0, limit line length to 72, ensure two spaces
follow all full stops, ensure uniform use of newlines after heading.
Fixes commit (
85d63445f411 Documentation: e100: Update the Intel 10/100 driver doc)
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tobin C. Harding [Fri, 22 Jun 2018 00:37:06 +0000 (10:37 +1000)]
Documentation: e1000: Use correct heading adornment
Recently documentation file was converted to rst. The document title
has the incorrect heading adornment. From kernel docs:
* Please stick to this order of heading adornments:
1. ``=`` with overline for document title::
==============
Document title
==============
Add overline heading adornment to document title.
Fixes commit (
228046e76189 Documentation: e1000: Update kernel documentation)
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tobin C. Harding [Fri, 22 Jun 2018 00:37:05 +0000 (10:37 +1000)]
Documentation: e100: Use correct heading adornment
Recently documentation file was converted to rst. The document title
has the incorrect heading adornment. From kernel docs:
* Please stick to this order of heading adornments:
1. ``=`` with overline for document title::
==============
Document title
==============
Add overline heading adornment to document title.
Fixes commit (
85d63445f411 Documentation: e100: Update the Intel 10/100 driver doc)
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Thu, 21 Jun 2018 11:49:36 +0000 (19:49 +0800)]
ipv6: mcast: fix unsolicited report interval after receiving querys
After recieving MLD querys, we update idev->mc_maxdelay with max_delay
from query header. This make the later unsolicited reports have the same
interval with mc_maxdelay, which means we may send unsolicited reports with
long interval time instead of default configured interval time.
Also as we will not call ipv6_mc_reset() after device up. This issue will
be there even after leave the group and join other groups.
Fixes: fc4eba58b4c14 ("ipv6: make unsolicited report intervals configurable for mld")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Thu, 21 Jun 2018 05:11:31 +0000 (13:11 +0800)]
vhost_net: validate sock before trying to put its fd
Sock will be NULL if we pass -1 to vhost_net_set_backend(), but when
we meet errors during ubuf allocation, the code does not check for
NULL before calling sockfd_put(), this will lead NULL
dereferencing. Fixing by checking sock pointer before.
Fixes: bab632d69ee4 ("vhost: vhost TX zero-copy support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suravee Suthikulpanit [Wed, 13 Jun 2018 18:43:10 +0000 (13:43 -0500)]
x86/CPU/AMD: Fix LLC ID bit-shift calculation
The current logic incorrectly calculates the LLC ID from the APIC ID.
Unless specified otherwise, the LLC ID should be calculated by removing
the Core and Thread ID bits from the least significant end of the APIC
ID. For more info, see "ApicId Enumeration Requirements" in any Fam17h
PPR document.
[ bp: Improve commit message. ]
Fixes: 68091ee7ac3c ("Calculate last level cache ID from number of sharing threads")
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1528915390-30533-1-git-send-email-suravee.suthikulpanit@amd.com
Thomas Gleixner [Fri, 22 Jun 2018 19:20:35 +0000 (21:20 +0200)]
Merge branch 'linus' into x86/urgent
Required to queue a dependent fix.
Jan Kara [Mon, 18 Jun 2018 13:46:58 +0000 (15:46 +0200)]
bdi: Fix another oops in wb_workfn()
syzbot is reporting NULL pointer dereference at wb_workfn() [1] due to
wb->bdi->dev being NULL. And Dmitry confirmed that wb->state was
WB_shutting_down after wb->bdi->dev became NULL. This indicates that
unregister_bdi() failed to call wb_shutdown() on one of wb objects.
The problem is in cgwb_bdi_unregister() which does cgwb_kill() and thus
drops bdi's reference to wb structures before going through the list of
wbs again and calling wb_shutdown() on each of them. This way the loop
iterating through all wbs can easily miss a wb if that wb has already
passed through cgwb_remove_from_bdi_list() called from wb_shutdown()
from cgwb_release_workfn() and as a result fully shutdown bdi although
wb_workfn() for this wb structure is still running. In fact there are
also other ways cgwb_bdi_unregister() can race with
cgwb_release_workfn() leading e.g. to use-after-free issues:
CPU1 CPU2
cgwb_bdi_unregister()
cgwb_kill(*slot);
cgwb_release()
queue_work(cgwb_release_wq, &wb->release_work);
cgwb_release_workfn()
wb = list_first_entry(&bdi->wb_list, ...)
spin_unlock_irq(&cgwb_lock);
wb_shutdown(wb);
...
kfree_rcu(wb, rcu);
wb_shutdown(wb); -> oops use-after-free
We solve these issues by synchronizing writeback structure shutdown from
cgwb_bdi_unregister() with cgwb_release_workfn() using a new mutex. That
way we also no longer need synchronization using WB_shutting_down as the
mutex provides it for CONFIG_CGROUP_WRITEBACK case and without
CONFIG_CGROUP_WRITEBACK wb_shutdown() can be called only once from
bdi_unregister().
Reported-by: syzbot <syzbot+4a7438e774b21ddd8eca@syzkaller.appspotmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Geert Uytterhoeven [Fri, 22 Jun 2018 11:05:35 +0000 (13:05 +0200)]
lightnvm: Remove depends on HAS_DMA in case of platform dependency
Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST".
In most cases this other symbol is an architecture or platform specific
symbol, or PCI.
Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.
This simplifies the dependencies, and allows to improve compile-testing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Will Deacon [Fri, 22 Jun 2018 10:45:07 +0000 (11:45 +0100)]
rseq: Avoid infinite recursion when delivering SIGSEGV
When delivering a signal to a task that is using rseq, we call into
__rseq_handle_notify_resume() so that the registers pushed in the
sigframe are updated to reflect the state of the restartable sequence
(for example, ensuring that the signal returns to the abort handler if
necessary).
However, if the rseq management fails due to an unrecoverable fault when
accessing userspace or certain combinations of RSEQ_CS_* flags, then we
will attempt to deliver a SIGSEGV. This has the potential for infinite
recursion if the rseq code continuously fails on signal delivery.
Avoid this problem by using force_sigsegv() instead of force_sig(), which
is explicitly designed to reset the SEGV handler to SIG_DFL in the case
of a recursive fault. In doing so, remove rseq_signal_deliver() from the
internal rseq API and have an optional struct ksignal * parameter to
rseq_handle_notify_resume() instead.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: peterz@infradead.org
Cc: paulmck@linux.vnet.ibm.com
Cc: boqun.feng@gmail.com
Link: https://lkml.kernel.org/r/1529664307-983-1-git-send-email-will.deacon@arm.com
Will Deacon [Fri, 22 Jun 2018 15:23:45 +0000 (16:23 +0100)]
arm64: mm: Ensure writes to swapper are ordered wrt subsequent cache maintenance
When rewriting swapper using nG mappings, we must performance cache
maintenance around each page table access in order to avoid coherency
problems with the host's cacheable alias under KVM. To ensure correct
ordering of the maintenance with respect to Device memory accesses made
with the Stage-1 MMU disabled, DMBs need to be added between the
maintenance and the corresponding memory access.
This patch adds a missing DMB between writing a new page table entry and
performing a clean+invalidate on the same line.
Fixes: f992b4dfd58b ("arm64: kpti: Add ->enable callback to remap swapper using nG mappings")
Cc: <stable@vger.kernel.org> # 4.16.x-
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Will Deacon [Fri, 22 Jun 2018 09:25:25 +0000 (10:25 +0100)]
arm64: kpti: Use early_param for kpti= command-line option
We inspect __kpti_forced early on as part of the cpufeature enable
callback which remaps the swapper page table using non-global entries.
Ensure that __kpti_forced has been updated to reflect the kpti=
command-line option before we start using it.
Fixes: ea1e3de85e94 ("arm64: entry: Add fake CPU feature for unmapping the kernel at EL0")
Cc: <stable@vger.kernel.org> # 4.16.x-
Reported-by: Wei Xu <xuwei5@hisilicon.com>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Geert Uytterhoeven [Fri, 22 Jun 2018 10:08:20 +0000 (12:08 +0200)]
MAINTAINERS: Add file patterns for x86 device tree bindings
Submitters of device tree binding documentation may forget to CC
the subsystem maintainer if this is missing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "H . Peter Anvin" <hpa@zytor.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Link: https://lkml.kernel.org/r/20180622100820.29616-1-geert@linux-m68k.org
Geert Uytterhoeven [Fri, 22 Jun 2018 14:33:57 +0000 (16:33 +0200)]
time: Make sure jiffies_to_msecs() preserves non-zero time periods
For the common cases where 1000 is a multiple of HZ, or HZ is a multiple of
1000, jiffies_to_msecs() never returns zero when passed a non-zero time
period.
However, if HZ > 1000 and not an integer multiple of 1000 (e.g. 1024 or
1200, as used on alpha and DECstation), jiffies_to_msecs() may return zero
for small non-zero time periods. This may break code that relies on
receiving back a non-zero value.
jiffies_to_usecs() does not need such a fix: one jiffy can only be less
than one µs if HZ >
1000000, and such large values of HZ are already
rejected at build time, twice:
- include/linux/jiffies.h does #error if HZ >= 12288,
- kernel/time/time.c has BUILD_BUG_ON(HZ > USEC_PER_SEC).
Broken since forever.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-alpha@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20180622143357.7495-1-geert@linux-m68k.org
Vitaly Kuznetsov [Fri, 22 Jun 2018 14:56:14 +0000 (16:56 +0200)]
KVM: fix KVM_CAP_HYPERV_TLBFLUSH paragraph number
KVM_CAP_HYPERV_TLBFLUSH collided with KVM_CAP_S390_PSW-BPB, its paragraph
number should now be 8.18.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Marc Orr [Thu, 21 Jun 2018 00:21:29 +0000 (17:21 -0700)]
kvm: vmx: Nested VM-entry prereqs for event inj.
This patch extends the checks done prior to a nested VM entry.
Specifically, it extends the check_vmentry_prereqs function with checks
for fields relevant to the VM-entry event injection information, as
described in the Intel SDM, volume 3.
This patch is motivated by a syzkaller bug, where a bad VM-entry
interruption information field is generated in the VMCS02, which causes
the nested VM launch to fail. Then, KVM fails to resume L1.
While KVM should be improved to correctly resume L1 execution after a
failed nested launch, this change is justified because the existing code
to resume L1 is flaky/ad-hoc and the test coverage for resuming L1 is
sparse.
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Marc Orr <marcorr@google.com>
[Removed comment whose parts were describing previous revisions and the
rest was obvious from function/variable naming. - Radim]
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Jens Axboe [Fri, 22 Jun 2018 14:45:29 +0000 (08:45 -0600)]
Merge branch 'nvme-4.18' of git://git.infradead.org/nvme into for-linus
Pull NVMe fixes from Christoph:
"Various relatively small fixes, mostly to fix error handling of various
sorts."
* 'nvme-4.18' of git://git.infradead.org/nvme:
nvme-pci: limit max IO size and segments to avoid high order allocations
nvme-pci: move nvme_kill_queues to nvme_remove_dead_ctrl
nvme-fc: release io queues to allow fast fail
nvmet: reset keep alive timer in controller enable
nvme-rdma: don't override opts->queue_size
nvme-rdma: Fix command completion race at error recovery
nvme-rdma: fix possible free of a non-allocated async event buffer
nvme-rdma: fix possible double free condition when failing to create a controller
Radim Krčmář [Fri, 22 Jun 2018 12:56:19 +0000 (14:56 +0200)]
Merge tag 'kvmarm-fixes-for-4.18-1' of git://git./linux/kernel/git/kvmarm/kvmarm
KVM/arm fixes for 4.18, take #1
- Lazy FPSIMD switching fixes
- Really disable compat ioctls on architectures that don't want it
- Disable compat on arm64 (it was never implemented...)
- Rely on architectural requirements for GICV on GICv3
- Detect bad alignments in unmap_stage2_range
Zhenzhong Duan [Fri, 22 Jun 2018 11:51:26 +0000 (13:51 +0200)]
x86/microcode/intel: Fix memleak in save_microcode_patch()
Free useless ucode_patch entry when it's replaced.
[ bp: Drop the memfree_patch() two-liner. ]
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@oracle.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Srinivas REDDY Eeda <srinivas.eeda@oracle.com>
Link: http://lkml.kernel.org/r/888102f0-fd22-459d-b090-a1bd8a00cb2b@default
Tony Luck [Fri, 22 Jun 2018 09:54:23 +0000 (11:54 +0200)]
x86/mce: Fix incorrect "Machine check from unknown source" message
Some injection testing resulted in the following console log:
mce: [Hardware Error]: CPU 22: Machine Check Exception: f Bank 1:
bd80000000100134
mce: [Hardware Error]: RIP 10:<
ffffffffc05292dd> {pmem_do_bvec+0x11d/0x330 [nd_pmem]}
mce: [Hardware Error]: TSC
c51a63035d52 ADDR
3234bc4000 MISC 88
mce: [Hardware Error]: PROCESSOR 0:50654 TIME
1526502199 SOCKET 0 APIC 38 microcode
2000043
mce: [Hardware Error]: Run the above through 'mcelog --ascii'
Kernel panic - not syncing: Machine check from unknown source
This confused everybody because the first line quite clearly shows
that we found a logged error in "Bank 1", while the last line says
"unknown source".
The problem is that the Linux code doesn't do the right thing
for a local machine check that results in a fatal error.
It turns out that we know very early in the handler whether the
machine check is fatal. The call to mce_no_way_out() has checked
all the banks for the CPU that took the local machine check. If
it says we must crash, we can do so right away with the right
messages.
We do scan all the banks again. This means that we might initially
not see a problem, but during the second scan find something fatal.
If this happens we print a slightly different message (so I can
see if it actually every happens).
[ bp: Remove unneeded severity assignment. ]
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: stable@vger.kernel.org # 4.2
Link: http://lkml.kernel.org/r/52e049a497e86fd0b71c529651def8871c804df0.1527283897.git.tony.luck@intel.com
Borislav Petkov [Fri, 22 Jun 2018 09:54:28 +0000 (11:54 +0200)]
x86/mce: Do not overwrite MCi_STATUS in mce_no_way_out()
mce_no_way_out() does a quick check during #MC to see whether some of
the MCEs logged would require the kernel to panic immediately. And it
passes a struct mce where MCi_STATUS gets written.
However, after having saved a valid status value, the next iteration
of the loop which goes over the MCA banks on the CPU, overwrites the
valid status value because we're using struct mce as storage instead of
a temporary variable.
Which leads to MCE records with an empty status value:
mce: [Hardware Error]: CPU 0: Machine Check Exception: 6 Bank 0:
0000000000000000
mce: [Hardware Error]: RIP 10:<
ffffffffbd42fbd7> {trigger_mce+0x7/0x10}
In order to prevent the loss of the status register value, return
immediately when severity is a panic one so that we can panic
immediately with the first fatal MCE logged. This is also the intention
of this function and not to noodle over the banks while a fatal MCE is
already logged.
Tony: read the rest of the MCA bank to populate the struct mce fully.
Suggested-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20180622095428.626-8-bp@alien8.de
John Garry [Fri, 22 Jun 2018 11:35:33 +0000 (19:35 +0800)]
irqdesc: Delete irq_desc_get_msi_desc()
Function irq_desc_get_msi_desc() is not referenced in the kernel (and does
not seem to have been referenced since
e39758e0ea76, 3 years ago), so
delete it.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <marc.zyngier@arm.com>
Cc: <will.deacon@arm.com>
Cc: <kstewart@linuxfoundation.org>
Cc: <julien.thierry@arm.com>
Cc: <andrew@lunn.ch>
Cc: <trivial@kernel.org>
Link: https://lkml.kernel.org/r/1529667333-92959-1-git-send-email-john.garry@huawei.com
Marc Zyngier [Fri, 22 Jun 2018 09:52:54 +0000 (10:52 +0100)]
irqchip/gic-v3-its: Fix reprogramming of redistributors on CPU hotplug
Enabling LPIs was made a lot stricter recently, by checking that they are
disabled before enabling them. By doing so, the CPU hotplug case was missed
altogether, which leaves LPIs enabled on hotplug off (expecting the CPU to
eventually come back), and won't write a different value anyway on hotplug
on.
So skip that check if that particular case is detected
Fixes: 6eb486b66a30 ("irqchip/gic-v3: Ensure GICR_CTLR.EnableLPI=0 is observed before enabling")
Reported-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lkml.kernel.org/r/20180622095254.5906-8-marc.zyngier@arm.com
Marc Zyngier [Fri, 22 Jun 2018 09:52:53 +0000 (10:52 +0100)]
irqchip/gic-v3-its: Only emit VSYNC if targetting a valid collection
Similarily to the SYNC operation, it must be verified that the VPE
targetted by a VLPI is backed by a valid collection in the GIC driver data
structures.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Yang Yingliang <yangyingliang@huawei.com>
Cc: Sumit Garg <sumit.garg@linaro.org>
Link: https://lkml.kernel.org/r/20180622095254.5906-7-marc.zyngier@arm.com
Marc Zyngier [Fri, 22 Jun 2018 09:52:52 +0000 (10:52 +0100)]
irqchip/gic-v3-its: Only emit SYNC if targetting a valid collection
It is possible, under obscure circumstances, to convince the ITS driver to
emit a SYNC operation that targets a collection that is not bound to any
redistributor (and the target_address field is zero) because the
corresponding CPU has not been seen yet (the system has been booted with
max_cpus="something small").
If the ITS is using the linear CPU number as the target, this is not a big
deal, as we just end-up issuing a SYNC to CPU0. But if the ITS requires the
physical address of the redistributor (with GITS_TYPER.PTA==1), we end-up
asking the ITS to write to the physical address zero, which is not exactly
a good idea (there has been report of the ITS locking up). This should of
course never happen, but hey, this is SW...
In order to avoid the above disaster, let's track which collections have
been actually initialized, and let's not generate a SYNC if the collection
hasn't been properly bound to a redistributor. Take this opportunity to
spit our a warning, in the hope that someone may report the issue if it
arrises again.
Reported-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Sumit Garg <sumit.garg@linaro.org>
Link: https://lkml.kernel.org/r/20180622095254.5906-6-marc.zyngier@arm.com
Yang Yingliang [Fri, 22 Jun 2018 09:52:51 +0000 (10:52 +0100)]
irqchip/gic-v3-its: Don't bind LPI to unavailable NUMA node
On a NUMA system, if an ITS is local to an offline node, the ITS driver may
pick an offline CPU to bind the LPI. In this case, pick an online CPU (and
the first one will do).
But on some systems, binding an LPI to non-local node CPU may cause
deadlock (see Cavium erratum 23144). In this case, just fail the activate
and return an error code.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Sumit Garg <sumit.garg@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20180622095254.5906-5-marc.zyngier@arm.com
Marc Zyngier [Fri, 22 Jun 2018 09:52:50 +0000 (10:52 +0100)]
irqchip/gic-v2m: Fix SPI release on error path
On failing to allocate the required SPIs, the actual number of interrupts
should be freed and not its log2 value.
Fixes: de337ee30142 ("irqchip/gic-v2m: Add PCI Multi-MSI support")
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Yang Yingliang <yangyingliang@huawei.com>
Cc: Sumit Garg <sumit.garg@linaro.org>
Link: https://lkml.kernel.org/r/20180622095254.5906-4-marc.zyngier@arm.com
Marc Zyngier [Fri, 22 Jun 2018 09:52:49 +0000 (10:52 +0100)]
irqchip/ls-scfg-msi: Fix MSI affinity handling
The ls-scfs-msi driver is not dealing with the effective affinity
as it should. Let's fix that, and make it clear that the effective
affinity is restricted to a single CPU. Also prevent the driver from
messing with the internals of the affinity setting infrastructure.
Reported-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Yang Yingliang <yangyingliang@huawei.com>
Cc: Sumit Garg <sumit.garg@linaro.org>
Link: https://lkml.kernel.org/r/20180622095254.5906-3-marc.zyngier@arm.com
Marc Zyngier [Fri, 22 Jun 2018 09:52:48 +0000 (10:52 +0100)]
genirq/debugfs: Add missing IRQCHIP_SUPPORTS_LEVEL_MSI debug
Debug is missing the IRQCHIP_SUPPORTS_LEVEL_MSI debug entry, making debugfs
slightly less useful.
Take this opportunity to also add a missing comment in the definition of
IRQCHIP_SUPPORTS_LEVEL_MSI.
Fixes: 6988e0e0d283 ("genirq/msi: Limit level-triggered MSI to platform devices")
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Yang Yingliang <yangyingliang@huawei.com>
Cc: Sumit Garg <sumit.garg@linaro.org>
Link: https://lkml.kernel.org/r/20180622095254.5906-2-marc.zyngier@arm.com
Mathieu Malaterre [Thu, 8 Mar 2018 20:28:56 +0000 (21:28 +0100)]
perf/core: Move the inline keyword at the beginning of the function declaration
When building perf with W=1 the following warning triggers:
CC kernel/events/ring_buffer.o
kernel/events/ring_buffer.c:105:1: warning: ‘inline’ is not at beginning of declaration [-Wold-style-declaration]
static bool __always_inline
^~~~~~
...
Move the inline keyword to the beginning of the function declaration.
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: trival@kernel.org
Link: http://lkml.kernel.org/r/20180308202856.9378-1-malat@debian.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Linus Torvalds [Fri, 22 Jun 2018 09:04:56 +0000 (18:04 +0900)]
Merge tag 'for_v4.18-rc2' of git://git./linux/kernel/git/jack/linux-fs
Pull udf, quota, ext2 fixes from Jan Kara:
"UDF:
- fix an oops due to corrupted disk image
- two small cleanups
quota:
- a fixfor lru handling
- cleanup
ext2:
- a warning about a deprecated mount option"
* tag 'for_v4.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
udf: Drop unused arguments of udf_delete_aext()
udf: Provide function for calculating dir entry length
udf: Detect incorrect directory size
ext2: add warning when specifying nocheck option
quota: Cleanup list iteration in dqcache_shrink_scan()
quota: reclaim least recently used dquots
Hans de Goede [Fri, 22 Jun 2018 06:42:22 +0000 (08:42 +0200)]
efi/libstub/tpm: Initialize efi_physical_addr_t vars to zero for mixed mode
Commit:
79832f0b5f71 ("efi/libstub/tpm: Initialize pointer variables to zero for mixed mode")
fixes a problem with the tpm code on mixed mode (64-bit kernel on 32-bit UEFI),
where 64-bit pointer variables are not fully initialized by the 32-bit EFI code.
A similar problem applies to the efi_physical_addr_t variables which
are written by the ->get_event_log() EFI call. Even though efi_physical_addr_t
is 64-bit everywhere, it seems that some 32-bit UEFI implementations only
fill in the lower 32 bits when passed a pointer to an efi_physical_addr_t
to fill.
This commit initializes these to 0 to, to ensure the upper 32 bits are
0 in mixed mode. This fixes recent kernels sometimes hanging during
early boot on mixed mode UEFI systems.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: <stable@vger.kernel.org> # v4.16+
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20180622064222.11633-2-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Boris Ostrovsky [Thu, 21 Jun 2018 17:29:44 +0000 (13:29 -0400)]
xen: Remove unnecessary BUG_ON from __unbind_from_irq()
Commit
910f8befdf5b ("xen/pirq: fix error path cleanup when binding
MSIs") fixed a couple of errors in error cleanup path of
xen_bind_pirq_msi_to_irq(). This cleanup allowed a call to
__unbind_from_irq() with an unbound irq, which would result in
triggering the BUG_ON there.
Since there is really no reason for the BUG_ON (xen_free_irq() can
operate on unbound irqs) we can remove it.
Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: stable@vger.kernel.org
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Juergen Gross [Mon, 18 Jun 2018 07:36:39 +0000 (09:36 +0200)]
xen: add new hypercall buffer mapping device
For passing arbitrary data from user land to the Xen hypervisor the
Xen tools today are using mlock()ed buffers. Unfortunately the kernel
might change access rights of such buffers for brief periods of time
e.g. for page migration or compaction, leading to access faults in the
hypervisor, as the hypervisor can't use the locks of the kernel.
In order to solve this problem add a new device node to the Xen privcmd
driver to easily allocate hypercall buffers via mmap(). The memory is
allocated in the kernel and just mapped into user space. Marked as
VM_IO the user mapping will not be subject to page migration et al.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Linus Torvalds [Fri, 22 Jun 2018 03:32:09 +0000 (12:32 +0900)]
Merge tag 'drm-fixes-2018-06-22' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Just run of the mill fixes,
core:
- regression fix in device unplug
qxl:
- regression fix for might sleep in cursor handling
nouveau:
- regression fix in multi-screen cursor handling
amdgpu:
- switch off DC by default on Kaveri and older
- some minor fixes
i915:
- some GEM regression fixes
- doublescan mode fixes
sun4i:
- revert fix for a regression
sii8620 bridge:
- misc fixes"
* tag 'drm-fixes-2018-06-22' of git://anongit.freedesktop.org/drm/drm: (28 commits)
drm/bridge/sii8620: fix display of packed pixel modes in MHL2
drm/amdgpu: Make amdgpu_vram_mgr_bo_invisible_size always accurate
drm/amdgpu: Refactor amdgpu_vram_mgr_bo_invisible_size helper
drm/amdgpu: Update pin_size values before unpinning BO
drm/amdgpu:All UVD instances share one idle_work handle
drm/amdgpu: Don't default to DC support for Kaveri and older
drm/amdgpu: Use kvmalloc_array for allocating VRAM manager nodes array
drm/amd/pp: Fix uninitialized variable
drm/i915: Enable provoking vertex fix on Gen9 systems.
drm/i915: Fix context ban and hang accounting for client
drm/i915: Turn off g4x DP port in .post_disable()
drm/i915: Disallow interlaced modes on g4x DP outputs
drm/i915: Fix PIPESTAT irq ack on i965/g4x
drm/i915: Allow DBLSCAN user modes with eDP/LVDS/DSI
drm/i915/execlists: Avoid putting the error pointer
drm/i915: Apply batch location restrictions before pinning
drm/nouveau/kms/nv50-: cursors always use core channel vram ctxdma
Revert "drm/sun4i: Handle DRM_BUS_FLAG_PIXDATA_*EDGE"
drm/atmel-hlcdc: check stride values in the first plane
drm/bridge/sii8620: fix HDMI cable connection to dongle
...
Steven Rostedt (VMware) [Fri, 22 Jun 2018 00:35:26 +0000 (20:35 -0400)]
locking/qspinlock: Fix build for anonymous union in older GCC compilers
One of my tests compiles the kernel with gcc 4.5.3, and I hit the
following build error:
include/linux/semaphore.h: In function 'sema_init':
include/linux/semaphore.h:35:17: error: unknown field 'val' specified in initializer
include/linux/semaphore.h:35:17: warning: missing braces around initializer
include/linux/semaphore.h:35:17: warning: (near initialization for '(anonymous).raw_lock.<anonymous>.val')
I bisected it down to:
625e88be1f41 ("locking/qspinlock: Merge 'struct __qspinlock' into 'struct qspinlock'")
... which makes qspinlock have an anonymous union, which makes initializing it special
for older compilers. By adding strategic brackets, it makes the build
happy again.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Acked-by: Waiman Long <longman@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Fixes: 625e88be1f41 ("locking/qspinlock: Merge 'struct __qspinlock' into 'struct qspinlock'")
Link: http://lkml.kernel.org/r/20180621203526.172ab5c4@vmware.local.home
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Dave Airlie [Thu, 21 Jun 2018 23:58:57 +0000 (09:58 +1000)]
Merge tag 'drm-misc-fixes-2018-06-21' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Fixes for v4.18-rc2:
- A reversion of a commit in drm/sun4i to fix a run-time fault.
- Various fixes to the sii8620 bridge.
- Small bugfix to correctly check stride in atmel-hlcdc.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/787d4bef-a579-4046-d0fc-f8c2c5b80c25@linux.intel.com
Claudio Imbrenda [Wed, 20 Jun 2018 13:51:51 +0000 (15:51 +0200)]
VSOCK: fix loopback on big-endian systems
The dst_cid and src_cid are 64 bits, therefore 64 bit accessors should be
used, and in fact in virtio_transport_common.c only 64 bit accessors are
used. Using 32 bit accessors for 64 bit values breaks big endian systems.
This patch fixes a wrong use of le32_to_cpu in virtio_transport_send_pkt.
Fixes: b9116823189e85ccf384 ("VSOCK: add loopback to virtio_transport")
Signed-off-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Thu, 21 Jun 2018 17:16:45 +0000 (18:16 +0100)]
net: ethernet: ti: davinci_cpdma: make function cpdma_desc_pool_create static
The function cpdma_desc_pool_create is local to the source and does not
need to be in global scope, so make it static.
Cleans up sparse warning:
warning: symbol 'cpdma_desc_pool_create' was not declared. Should it
be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dave Airlie [Thu, 21 Jun 2018 23:56:17 +0000 (09:56 +1000)]
Merge tag 'drm-intel-fixes-2018-06-21' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
drm/i915 fixes for v4.18-rc2:
- Mostly cc: stable display fixes, including a DBLSCAN regression fix
- GEM fixes for this merge window
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87d0wkuypy.fsf@intel.com
David S. Miller [Thu, 21 Jun 2018 22:54:54 +0000 (07:54 +0900)]
Merge branch 'xen-netfront-fixes'
Ross Lagerwall says:
====================
xen-netfront: Fix issues with commit
f599c64fdf7d
Fix a couple of issues with commit
f599c64fdf7d ("xen-netfront: Fix race
between device setup and open").
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ross Lagerwall [Thu, 21 Jun 2018 13:00:21 +0000 (14:00 +0100)]
xen-netfront: Update features after registering netdev
Update the features after calling register_netdev() otherwise the
device features are not set up correctly and it not possible to change
the MTU of the device. After this change, the features reported by
ethtool match the device's features before the commit which introduced
the issue and it is possible to change the device's MTU.
Fixes: f599c64fdf7d ("xen-netfront: Fix race between device setup and open")
Reported-by: Liam Shepherd <liam@dancer.es>
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ross Lagerwall [Thu, 21 Jun 2018 13:00:20 +0000 (14:00 +0100)]
xen-netfront: Fix mismatched rtnl_unlock
Fixes: f599c64fdf7d ("xen-netfront: Fix race between device setup and open")
Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Thu, 21 Jun 2018 18:02:16 +0000 (20:02 +0200)]
cls_flower: fix use after free in flower S/W path
If flower filter is created without the skip_sw flag, fl_mask_put()
can race with fl_classify() and we can destroy the mask rhashtable
while a lookup operation is accessing it.
BUG: unable to handle kernel paging request at
00000000000911d1
PGD 0 P4D 0
SMP PTI
CPU: 3 PID: 5582 Comm: vhost-5541 Not tainted 4.18.0-rc1.vanilla+ #1950
Hardware name: Dell Inc. PowerEdge R730/072T6D, BIOS 2.1.7 06/16/2016
RIP: 0010:rht_bucket_nested+0x20/0x60
Code: 31 c8 c1 c1 18 29 c8 c3 66 90 8b 4f 04 ba 01 00 00 00 8b 07 48 8b bf 80 00 00 0
RSP: 0018:
ffffafc5cfbb7a48 EFLAGS:
00010206
RAX:
0000000000001978 RBX:
ffff9f12dff88a00 RCX:
00000000ffff9f12
RDX:
00000000000911d1 RSI:
0000000000000148 RDI:
0000000000000001
RBP:
ffff9f12dff88a00 R08:
000000005f1cc119 R09:
00000000a715fae2
R10:
ffffafc5cfbb7aa8 R11:
ffff9f1cb4be804e R12:
ffff9f1265e13000
R13:
0000000000000000 R14:
ffffafc5cfbb7b48 R15:
ffff9f12dff88b68
FS:
0000000000000000(0000) GS:
ffff9f1d3f0c0000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
00000000000911d1 CR3:
0000001575a94006 CR4:
00000000001626e0
Call Trace:
fl_lookup+0x134/0x140 [cls_flower]
fl_classify+0xf3/0x180 [cls_flower]
tcf_classify+0x78/0x150
__netif_receive_skb_core+0x69e/0xa50
netif_receive_skb_internal+0x42/0xf0
tun_get_user+0xdd5/0xfd0 [tun]
tun_sendmsg+0x52/0x70 [tun]
handle_tx+0x2b3/0x5f0 [vhost_net]
vhost_worker+0xab/0x100 [vhost]
kthread+0xf8/0x130
ret_from_fork+0x35/0x40
Modules linked in: act_mirred act_gact cls_flower vhost_net vhost tap sch_ingress
CR2:
00000000000911d1
Fix the above waiting for a RCU grace period before destroying the
rhashtable: we need to use tcf_queue_work(), as rhashtable_destroy()
must run in process context, as pointed out by Cong Wang.
v1 -> v2: use tcf_queue_work to run rhashtable_destroy().
Fixes: 05cd271fd61a ("cls_flower: Support multiple masks per priority")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 21 Jun 2018 21:16:02 +0000 (14:16 -0700)]
net/packet: fix use-after-free
We should put copy_skb in receive_queue only after
a successful call to virtio_net_hdr_from_skb().
syzbot report :
BUG: KASAN: use-after-free in __skb_unlink include/linux/skbuff.h:1843 [inline]
BUG: KASAN: use-after-free in __skb_dequeue include/linux/skbuff.h:1863 [inline]
BUG: KASAN: use-after-free in skb_dequeue+0x16a/0x180 net/core/skbuff.c:2815
Read of size 8 at addr
ffff8801b044ecc0 by task syz-executor217/4553
CPU: 0 PID: 4553 Comm: syz-executor217 Not tainted 4.18.0-rc1+ #111
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1c9/0x2b4 lib/dump_stack.c:113
print_address_description+0x6c/0x20b mm/kasan/report.c:256
kasan_report_error mm/kasan/report.c:354 [inline]
kasan_report.cold.7+0x242/0x2fe mm/kasan/report.c:412
__asan_report_load8_noabort+0x14/0x20 mm/kasan/report.c:433
__skb_unlink include/linux/skbuff.h:1843 [inline]
__skb_dequeue include/linux/skbuff.h:1863 [inline]
skb_dequeue+0x16a/0x180 net/core/skbuff.c:2815
skb_queue_purge+0x26/0x40 net/core/skbuff.c:2852
packet_set_ring+0x675/0x1da0 net/packet/af_packet.c:4331
packet_release+0x630/0xd90 net/packet/af_packet.c:2991
__sock_release+0xd7/0x260 net/socket.c:603
sock_close+0x19/0x20 net/socket.c:1186
__fput+0x35b/0x8b0 fs/file_table.c:209
____fput+0x15/0x20 fs/file_table.c:243
task_work_run+0x1ec/0x2a0 kernel/task_work.c:113
exit_task_work include/linux/task_work.h:22 [inline]
do_exit+0x1b08/0x2750 kernel/exit.c:865
do_group_exit+0x177/0x440 kernel/exit.c:968
__do_sys_exit_group kernel/exit.c:979 [inline]
__se_sys_exit_group kernel/exit.c:977 [inline]
__x64_sys_exit_group+0x3e/0x50 kernel/exit.c:977
do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x4448e9
Code: Bad RIP value.
RSP: 002b:
00007ffd5f777ca8 EFLAGS:
00000202 ORIG_RAX:
00000000000000e7
RAX:
ffffffffffffffda RBX:
0000000000000000 RCX:
00000000004448e9
RDX:
00000000004448e9 RSI:
000000000000fcfb RDI:
0000000000000001
RBP:
00000000006cf018 R08:
00007ffd0000a45b R09:
0000000000000000
R10:
00007ffd5f777e48 R11:
0000000000000202 R12:
00000000004021f0
R13:
0000000000402280 R14:
0000000000000000 R15:
0000000000000000
Allocated by task 4553:
save_stack+0x43/0xd0 mm/kasan/kasan.c:448
set_track mm/kasan/kasan.c:460 [inline]
kasan_kmalloc+0xc4/0xe0 mm/kasan/kasan.c:553
kasan_slab_alloc+0x12/0x20 mm/kasan/kasan.c:490
kmem_cache_alloc+0x12e/0x760 mm/slab.c:3554
skb_clone+0x1f5/0x500 net/core/skbuff.c:1282
tpacket_rcv+0x28f7/0x3200 net/packet/af_packet.c:2221
deliver_skb net/core/dev.c:1925 [inline]
deliver_ptype_list_skb net/core/dev.c:1940 [inline]
__netif_receive_skb_core+0x1bfb/0x3680 net/core/dev.c:4611
__netif_receive_skb+0x2c/0x1e0 net/core/dev.c:4693
netif_receive_skb_internal+0x12e/0x7d0 net/core/dev.c:4767
netif_receive_skb+0xbf/0x420 net/core/dev.c:4791
tun_rx_batched.isra.55+0x4ba/0x8c0 drivers/net/tun.c:1571
tun_get_user+0x2af1/0x42f0 drivers/net/tun.c:1981
tun_chr_write_iter+0xb9/0x154 drivers/net/tun.c:2009
call_write_iter include/linux/fs.h:1795 [inline]
new_sync_write fs/read_write.c:474 [inline]
__vfs_write+0x6c6/0x9f0 fs/read_write.c:487
vfs_write+0x1f8/0x560 fs/read_write.c:549
ksys_write+0x101/0x260 fs/read_write.c:598
__do_sys_write fs/read_write.c:610 [inline]
__se_sys_write fs/read_write.c:607 [inline]
__x64_sys_write+0x73/0xb0 fs/read_write.c:607
do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Freed by task 4553:
save_stack+0x43/0xd0 mm/kasan/kasan.c:448
set_track mm/kasan/kasan.c:460 [inline]
__kasan_slab_free+0x11a/0x170 mm/kasan/kasan.c:521
kasan_slab_free+0xe/0x10 mm/kasan/kasan.c:528
__cache_free mm/slab.c:3498 [inline]
kmem_cache_free+0x86/0x2d0 mm/slab.c:3756
kfree_skbmem+0x154/0x230 net/core/skbuff.c:582
__kfree_skb net/core/skbuff.c:642 [inline]
kfree_skb+0x1a5/0x580 net/core/skbuff.c:659
tpacket_rcv+0x189e/0x3200 net/packet/af_packet.c:2385
deliver_skb net/core/dev.c:1925 [inline]
deliver_ptype_list_skb net/core/dev.c:1940 [inline]
__netif_receive_skb_core+0x1bfb/0x3680 net/core/dev.c:4611
__netif_receive_skb+0x2c/0x1e0 net/core/dev.c:4693
netif_receive_skb_internal+0x12e/0x7d0 net/core/dev.c:4767
netif_receive_skb+0xbf/0x420 net/core/dev.c:4791
tun_rx_batched.isra.55+0x4ba/0x8c0 drivers/net/tun.c:1571
tun_get_user+0x2af1/0x42f0 drivers/net/tun.c:1981
tun_chr_write_iter+0xb9/0x154 drivers/net/tun.c:2009
call_write_iter include/linux/fs.h:1795 [inline]
new_sync_write fs/read_write.c:474 [inline]
__vfs_write+0x6c6/0x9f0 fs/read_write.c:487
vfs_write+0x1f8/0x560 fs/read_write.c:549
ksys_write+0x101/0x260 fs/read_write.c:598
__do_sys_write fs/read_write.c:610 [inline]
__se_sys_write fs/read_write.c:607 [inline]
__x64_sys_write+0x73/0xb0 fs/read_write.c:607
do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
The buggy address belongs to the object at
ffff8801b044ecc0
which belongs to the cache skbuff_head_cache of size 232
The buggy address is located 0 bytes inside of
232-byte region [
ffff8801b044ecc0,
ffff8801b044eda8)
The buggy address belongs to the page:
page:
ffffea0006c11380 count:1 mapcount:0 mapping:
ffff8801d9be96c0 index:0x0
flags: 0x2fffc0000000100(slab)
raw:
02fffc0000000100 ffffea0006c17988 ffff8801d9bec248 ffff8801d9be96c0
raw:
0000000000000000 ffff8801b044e040 000000010000000c 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8801b044eb80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff8801b044ec00: 00 00 00 00 00 00 00 00 00 00 00 00 00 fc fc fc
>
ffff8801b044ec80: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb
^
ffff8801b044ed00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff8801b044ed80: fb fb fb fb fb fc fc fc fc fc fc fc fc fc fc fc
Fixes: 58d19b19cd99 ("packet: vnet_hdr support for tpacket_rcv")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 21 Jun 2018 21:21:34 +0000 (06:21 +0900)]
Merge tag 'nfs-for-4.18-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
"Hightlights include:
- fix an rcu deadlock in nfs_delegation_find_inode()
- fix NFSv4 deadlocks due to not freeing the session slot in
layoutget
- don't send layoutreturn if the layout is already invalid
- prevent duplicate XID allocation
- flexfiles: Don't tie up all the rpciod threads in resends"
* tag 'nfs-for-4.18-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
pNFS/flexfiles: Process writeback resends from nfsiod context as well
pNFS/flexfiles: Don't tie up all the rpciod threads in resends
sunrpc: Prevent duplicate XID allocation
pNFS: Don't send layoutreturn if the layout is already invalid
pNFS: Always free the session slot on error in nfs4_layoutget_handle_exception
NFS: Fix an rcu deadlock in nfs_delegation_find_inode()
Linus Torvalds [Thu, 21 Jun 2018 21:08:56 +0000 (06:08 +0900)]
Merge tag 'pinctrl-v4.18-2' of git://git./linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Some fallout in the pin control subsystem in the first week after the
merge window, some minor fixes so I'd like to get it to you ASAP.
- fix a serious kernel panic on the Mediatek driver with the external
interrupt controller.
- fix an uninitialized compiler warning in the owl (actions) driver.
- allocation failure in the pinctrl-single driver.
- pointer overwrite problem in the i.MX driver.
- fix a small compiler warning"
* tag 'pinctrl-v4.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: mt7622: fix a kernel panic when pio don't work as EINT controller
pinctrl: actions: Fix uninitialized error in owl_pin_config_set()
pinctrl: single: Add allocation failure checking of saved_vals
pinctrl: devicetree: Fix pctldev pointer overwrite
pinctrl: mediatek: remove redundant return value check of platform_get_resource()
Linus Torvalds [Thu, 21 Jun 2018 21:05:03 +0000 (06:05 +0900)]
Merge tag 'hwmon-for-linus-v4.18-rc2' of git://git./linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- fix a loop limit in nct6775 driver
- disable fan support for Dell XPS13 9333
* tag 'hwmon-for-linus-v4.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (nct6775) Fix loop limit
hwmon: (dell-smm) Disable fan support for Dell XPS13 9333
Linus Torvalds [Thu, 21 Jun 2018 21:00:13 +0000 (06:00 +0900)]
Merge tag 'acpi-4.18-rc2' of git://git./linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix a suspend/resume regression in the ACPI driver for Intel
SoCs (LPSS), add a new system wakeup quirk to the ACPI EC driver and
fix an inline stub of a function in the ACPI processor driver that
diverged from the original.
Specifics:
- Fix a suspend/resume regression in the ACPI driver for Intel SoCs
(LPSS) to make it work on systems where some power management
quirks should only be applied for runtime PM and suspend-to-idle
and not for suspend-to-RAM (Rafael Wysocki).
- Add a system wakeup quirk for Thinkpad X1 Carbon 6th to the ACPI EC
driver to avoid drainig battery too fast while suspended to idle on
those systems (Mika Westerberg).
- Fix an inline stub of acpi_processor_ppc_has_changed() to match the
original function definition (Brian Norris)"
* tag 'acpi-4.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / processor: Finish making acpi_processor_ppc_has_changed() void
ACPI / EC: Use ec_no_wakeup on Thinkpad X1 Carbon 6th
ACPI / LPSS: Avoid PM quirks on suspend and resume from S3
Linus Torvalds [Thu, 21 Jun 2018 20:57:36 +0000 (05:57 +0900)]
Merge tag 'pm-4.18-rc2' of git://git./linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These are mostly fixes, including some fixes for changes made during
the recent merge window and some "stable" material, plus some minor
extensions of the turbostat utility.
Specifics:
- Fix the PM core to avoid introducing a runtime PM usage counter
imbalance when adding device links during driver probe (Rafael
Wysocki).
- Fix the operating performance points (OPP) framework to ensure that
the regulator voltage is always updated as appropriate when
updating clock rates (Waldemar Rymarkiewicz).
- Fix the intel_pstate driver to use correct max/min limits for cores
with differing maximum frequences (Srinivas Pandruvada).
- Fix a typo in the intel_pstate driver documentation (Rafael
Wysocki).
- Fix two issues with the recently added Kryo cpufreq driver (Ilia
Lin).
- Fix two recent regressions and some other minor issues in the
turbostat utility and extend it to provide some more diagnostic
information (Len Brown, Nathan Ciobanu)"
* tag 'pm-4.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Documentation: intel_pstate: Fix typo
tools/power turbostat: version 18.06.20
tools/power turbostat: add the missing command line switches
tools/power turbostat: add single character tokens to help
tools/power turbostat: alphabetize the help output
tools/power turbostat: fix segfault on 'no node' machines
tools/power turbostat: add optional APIC X2APIC columns
tools/power turbostat: decode cpuid.1.HT
tools/power turbostat: fix show/hide issues resulting from mis-merge
PM / OPP: Update voltage in case freq == old_freq
cpufreq: intel_pstate: Fix scaling max/min limits with Turbo 3.0
cpufreq: kryo: Add module remove and exit
cpufreq: kryo: Fix possible error code dereference
PM / core: Fix supplier device runtime PM usage counter imbalance
Greg Thelen [Fri, 8 Jun 2018 21:47:46 +0000 (14:47 -0700)]
tracing: Fix SKIP_STACK_VALIDATION=1 build due to bad merge with -mrecord-mcount
Non gcc-5 builds with CONFIG_STACK_VALIDATION=y and
SKIP_STACK_VALIDATION=1 fail.
Example output:
/bin/sh: init/.tmp_main.o: Permission denied
commit
96f60dfa5819 ("trace: Use -mcount-record for dynamic ftrace"),
added a mismatched endif. This causes cmd_objtool to get mistakenly
set.
Relocate endif to balance the newly added -record-mcount check.
Link: http://lkml.kernel.org/r/20180608214746.136554-1-gthelen@google.com
Fixes: 96f60dfa5819 ("trace: Use -mcount-record for dynamic ftrace")
Acked-by: Andi Kleen <ak@linux.intel.com>
Tested-by: David Rientjes <rientjes@google.com>
Signed-off-by: Greg Thelen <gthelen@google.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Joel Fernandes (Google) [Thu, 14 Jun 2018 22:48:59 +0000 (15:48 -0700)]
tracing: Fix some errors in histogram documentation
Fix typos, inconsistencies in using quotes, incorrect section number,
etc. in the trace histogram documentation.
Link: http://lkml.kernel.org/r/20180614224859.55864-1-joel@joelfernandes.org
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Gustavo A. R. Silva [Fri, 9 Feb 2018 17:53:16 +0000 (11:53 -0600)]
tracing: Use swap macro in update_max_tr
Make use of the swap macro and remove unnecessary variable _buf_.
This makes the code easier to read and maintain. Also, reduces the
stack usage.
This code was detected with the help of Coccinelle.
Link: http://lkml.kernel.org/r/20180209175316.GA18720@embeddedgus
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Joel Fernandes (Google) [Thu, 7 Jun 2018 20:11:43 +0000 (13:11 -0700)]
softirq: Reorder trace_softirqs_on to prevent lockdep splat
I'm able to reproduce a lockdep splat with config options:
CONFIG_PROVE_LOCKING=y,
CONFIG_DEBUG_LOCK_ALLOC=y and
CONFIG_PREEMPTIRQ_EVENTS=y
$ echo 1 > /d/tracing/events/preemptirq/preempt_enable/enable
[ 26.112609] DEBUG_LOCKS_WARN_ON(current->softirqs_enabled)
[ 26.112636] WARNING: CPU: 0 PID: 118 at kernel/locking/lockdep.c:3854
[...]
[ 26.144229] Call Trace:
[ 26.144926] <IRQ>
[ 26.145506] lock_acquire+0x55/0x1b0
[ 26.146499] ? __do_softirq+0x46f/0x4d9
[ 26.147571] ? __do_softirq+0x46f/0x4d9
[ 26.148646] trace_preempt_on+0x8f/0x240
[ 26.149744] ? trace_preempt_on+0x4d/0x240
[ 26.150862] ? __do_softirq+0x46f/0x4d9
[ 26.151930] preempt_count_sub+0x18a/0x1a0
[ 26.152985] __do_softirq+0x46f/0x4d9
[ 26.153937] irq_exit+0x68/0xe0
[ 26.154755] smp_apic_timer_interrupt+0x271/0x280
[ 26.156056] apic_timer_interrupt+0xf/0x20
[ 26.157105] </IRQ>
The issue was this:
preempt_count = 1 << SOFTIRQ_SHIFT
__local_bh_enable(cnt = 1 << SOFTIRQ_SHIFT) {
if (softirq_count() == (cnt && SOFTIRQ_MASK)) {
trace_softirqs_on() {
current->softirqs_enabled = 1;
}
}
preempt_count_sub(cnt) {
trace_preempt_on() {
tracepoint() {
rcu_read_lock_sched() {
// jumps into lockdep
Where preempt_count still has softirqs disabled, but
current->softirqs_enabled is true, and we get a splat.
Link: http://lkml.kernel.org/r/20180607201143.247775-1-joel@joelfernandes.org
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Tom Zanussi <tom.zanussi@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Thomas Glexiner <tglx@linutronix.de>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Todd Kjos <tkjos@google.com>
Cc: Erick Reyes <erickreyes@google.com>
Cc: Julia Cartwright <julia@ni.com>
Cc: Byungchul Park <byungchul.park@lge.com>
Cc: stable@vger.kernel.org
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Fixes: d59158162e032 ("tracing: Add support for preempt and irq enable/disable events")
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Steven Rostedt (VMware) [Thu, 21 Jun 2018 17:20:53 +0000 (13:20 -0400)]
tracing: Check for no filter when processing event filters
The syzkaller detected a out-of-bounds issue with the events filter code,
specifically here:
prog[N].pred = NULL; /* #13 */
prog[N].target = 1; /* TRUE */
prog[N+1].pred = NULL;
prog[N+1].target = 0; /* FALSE */
-> prog[N-1].target = N;
prog[N-1].when_to_branch = false;
As that's the first reference to a "N-1" index, it appears that the code got
here with N = 0, which means the filter parser found no filter to parse
(which shouldn't ever happen, but apparently it did).
Add a new error to the parsing code that will check to make sure that N is
not zero before going into this part of the code. If N = 0, then -EINVAL is
returned, and a error message is added to the filter.
Cc: stable@vger.kernel.org
Fixes: 80765597bc587 ("tracing: Rewrite filter logic to be simpler and faster")
Reported-by: air icy <icytxw@gmail.com>
bugzilla url: https://bugzilla.kernel.org/show_bug.cgi?id=200019
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Jens Axboe [Thu, 21 Jun 2018 15:49:37 +0000 (09:49 -0600)]
nvme-pci: limit max IO size and segments to avoid high order allocations
nvme requires an sg table allocation for each request. If the request
is large, then the allocation can become quite large. For instance,
with our default software settings of 1280KB IO size, we'll need
10248 bytes of sg table. That turns into a 2nd order allocation,
which we can't always guarantee. If we fail the allocation, blk-mq
will retry it later. But there's no guarantee that we'll EVER be
able to allocate that much contigious memory.
Limit the IO size such that we never need more than a single page
of memory. That's a lot faster and more reliable. Then back that
allocation with a mempool, so that we know we'll always be able
to succeed the allocation at some point.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Acked-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Steven Rostedt (VMware) [Wed, 4 Apr 2018 18:06:30 +0000 (14:06 -0400)]
locking/lockdep: Do not record IRQ state within lockdep code
While debugging where things were going wrong with mapping
enabling/disabling interrupts with the lockdep state and actual real
enabling and disabling interrupts, I had to silent the IRQ
disabling/enabling in debug_check_no_locks_freed() because it was
always showing up as it was called before the splat was.
Use raw_local_irq_save/restore() for not only debug_check_no_locks_freed()
but for all internal lockdep functions, as they hide useful information
about where interrupts were used incorrectly last.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Link: https://lkml.kernel.org/lkml/20180404140630.3f4f4c7a@gandalf.local.home
Signed-off-by: Ingo Molnar <mingo@kernel.org>
projects / openwrt / staging / blogic.git / log