Etienne Champetier [Tue, 1 Mar 2022 04:00:22 +0000 (23:00 -0500)]
ebtables: rename to ebtables-legacy
This prepare the introduction of ebtables-nft.
Add PROVIDES so dependencies are not broken,
use ALTERNATIVES.
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
Etienne Champetier [Tue, 1 Mar 2022 03:37:41 +0000 (22:37 -0500)]
arptables: rename package to arptables-legacy
This prepare the introduction of arptables-nft.
Add PROVIDES so dependencies are not broken,
use ALTERNATIVES.
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
Rosen Penev [Fri, 26 Mar 2021 10:09:34 +0000 (03:09 -0700)]
quilt.mk: fix typo in the Host section
HOST_PATCH_DIR is used for host patches, not PATCH_DIR.
Fixes refreshing patches with a custom HOST_PATCH_DIR.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Josef Schlehofer [Wed, 16 Mar 2022 12:14:57 +0000 (13:14 +0100)]
cypress-firmware: update it to version 5.4.18-2021_0812
- Binary files were renamed to cyfmac from brcmfmac, but the files needs
to be on the router with the previous naming
[ 6.656165] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[ 6.665182] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac43455-sdio.bin failed with error -2
[ 6.674928] brcmfmac mmc1:0001:1: Falling back to sysfs fallback for: brcm/brcmfmac43455-sdio.bin
- Cypress were acquired by Infineon Technologies
Thus change the project URL and switch to download files from their
GitHub repository. This is much better than the previous solution, which
requires finding new threads on their community forum about new driver
updates, and it will be necessary to change the URL each time.
Unfortunately, it seems that there is not published changelog, but
according to this forum thread [1], be careful by opening the link from
solution since it contains ending bracket ), it brings fixes for various
security vulnerabilities, which were fixed in 7_45_234.
Fixes:
- FragAttacks
- Kr00k
Also add LICENSE file
Run tested on Seeedstudio router powered by Raspberry Pi 4 CM with
package cypress-firmware-43455-sdio.
Before:
root@OpenWrt:~# dmesg | grep 'Firmware: BCM4345/6'
[ 6.895050] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Mar 23 2020 02:20:01 version 7.45.206 (r725000 CY) FWID 01-
febaba43
After:
root@OpenWrt:~# dmesg | grep 'Firmware: BCM4345/6'
[ 6.829805] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Apr 15 2021 03:03:20 version 7.45.234 (
4ca95bb CY) FWID 01-
996384e2
[1] https://community.infineon.com/t5/Wi-Fi-Bluetooth-for-Linux/Outdated-brcmfmac-firmware-for-Raspberry-Pi-4-in-OpenWrt-21-02-1/m-p/331593#M2269
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Josef Schlehofer [Thu, 17 Mar 2022 17:49:57 +0000 (18:49 +0100)]
bcm27xx: bcm2711: add kmod-usb-net-lan78xx
Some vendors like Seeedstudio in their product [1] with Raspberry Pi
Compute Module 4 uses Microchip LAN7800 (USB 3.0 to Gigabit
Ethernet Bridge) - USB 3.0 extended from PCIe of CM4.
lsusb output:
```
Bus 002 Device 002: ID 0424:7800 Microchip LAN7800
```
Raspberry Pi 4 and even Compute Module 4 has many resources available
and for just one kernel module it is not necessary to add additional specific CM4 profiles.
Let's include it by default, so the both Ethernet ports will be usable
to have better user-experience. Because previous generation of Raspberry
Pi included LAN7800 Gigabit Ethernet by default and it is enabled there
[2] in kernel without additional kernel module, which was added recently [3].
After this commit in dmesg can be found this:
```
root@OpenWrt:~# dmesg | grep lan
[ 7.038889] lan78xx 2-3:1.0 (unnamed net_device) (uninitialized): int urb period 64
[ 7.090484] usbcore: registered new interface driver lan78xx
```
Tested and works with sysupgrade image.
[1] https://www.seeedstudio.com/Dual-GbE-Carrier-Board-with-4GB-RAM-32GB-eMMC-RPi-CM4-Case-p-5029.html
[2] https://github.com/openwrt/openwrt/blob/
32c74552b2310531af593ee0f859a3935a3a7cbd/target/linux/bcm27xx/bcm2709/config-5.4#L437
[3] https://github.com/openwrt/openwrt/commit/
31647d8be8c60bfb6690c87c739b8abe6dc03950
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Josef Schlehofer [Thu, 17 Mar 2022 23:07:50 +0000 (00:07 +0100)]
iwinfo: update to latest Git head
Changelog:
90bfbb9 devices: Add Cypress CYW43455
234075b devices: fix AMD RZ608 format
0e2a318 devices: add AMD RZ608 device-id
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Felix Fietkau [Sat, 19 Mar 2022 12:28:41 +0000 (13:28 +0100)]
bpftools: fix library path on 64 bit systems
drop the use of LIB_SUFFIX
Fixes: 00cbf6f6ab1d ("bpftools: update to standalone bpftools + libbpf, use the latest version")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Tue, 15 Mar 2022 13:33:59 +0000 (14:33 +0100)]
bpftools: update to standalone bpftools + libbpf, use the latest version
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Fri, 18 Mar 2022 13:36:57 +0000 (14:36 +0100)]
mac80211: backport MBSSID support
Required for an upcoming mt76 update
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Stijn Tintel [Mon, 14 Mar 2022 19:56:55 +0000 (21:56 +0200)]
kernel: enable SERIAL_8250_16550A_VARIANTS
Kernel 5.6 introduced a new config symbol SERIAL_8250_16550A_VARIANTS.
In kernel 5.8, this symbol was changed to default to on on !x86, as some
embedded devices still use 16650A variants. Let's play safe here and
enable this symbol in the generic config, to avoid others from running
into this problem and having to spend several hours trying to bisect
this problem. While we could disable the symbol in the x86 target
configs, a 20ms boot time reduction really isn't worth the time wasted
on bisecting this issue.
Matt discovered this problem while working on adding support for the
WatchGuard Firebox M200 to the qoriq target, where it caused some
characters to be missing on the console output.
Reported-by: Matt Fawcett <mattytap@icloud.com>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: Rui Salvaterra <rsalvaterra@gmail.com>
Pascal Coudurier [Tue, 25 Jan 2022 20:18:28 +0000 (21:18 +0100)]
ath79: improve support for GL.iNet GL-XE300
- fix eth0 eth1 sharing same mac so it conforms to the behavior stated
in the original commit and the way it is in vendor firmware :
WAN is label, LAN is label +1 and WLAN is label +2
- add default leds config
- add default network config
Signed-off-by: Pascal Coudurier <coudu@wanadoo.fr>
Petr Štetiar [Thu, 17 Mar 2022 06:53:55 +0000 (07:53 +0100)]
mpc85xx: fix missing kernel config symbol and DTS whitespace issue
Buildbot has reported following issue while crunching mpc85xx/p1010
subtarget:
Extreme Networks WS-AP3825i (WS_AP3825I) [N/y/?] (NEW)
Fix it by disabling that config symbol in target kernel config and while
at it fix DTS whitespace issue.
Fixes: 7e614820a892 ("mpc85xx: add support for Extreme Networks WS-AP3825i")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Jan Hoffmann [Wed, 16 Mar 2022 17:24:23 +0000 (18:24 +0100)]
lantiq: fritz7362sl: add partition subnode for SPI flash
Without a partition subnode ofpart_core still parses direct subnodes as
partitions, but it ignores nodes with a compatible property. Due to
this, the switch to nvmem-cells made the urlader partition inaccessible.
As a result, the wireless network was broken, as the calibration data
is read from that partition by a script.
Fixes: #8983
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Martin Blumenstingl [Tue, 15 Mar 2022 21:53:04 +0000 (22:53 +0100)]
lantiq: fritz7362sl: fix SPI flash node reg property
The &spi node has #address-cells = <1> and #size-cells = <0>. Drop the
extra 0 in the reg property from the SPI flash node to ensure it's
number of cells matches the definition in the parent node. This also
makes the reg property for the SPI flash node consistent with all other
VR9 boards.
Fixes: eae6cac6a30b ("lantiq: add support for AVM FRITZ!Box 7362 SL")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Christian Lamparter [Wed, 16 Mar 2022 16:34:24 +0000 (17:34 +0100)]
ipq806x: fix TP-Link Archer VR2600v bootlooping
Timo Schroeder reported:
"The TP-Link Archer VR2600v is stuck in a boot loop on written
snapshot image. It's able to boot using the snapshot uimage
though, but there ath10k firmware can't be found.
21.02.2 release version doesn't have either problem."
The VR2600v has a 512 byte header at the beginning of the
firmware that needs to be accounted for.
Fixes: f6a01d7f5c3d ("ipq806x: convert TP-Link Archer VR2600v to denx,uimage")
Reported-by: Timo Schroeder <der.timosch@gmail.com>
References: <https://github.com/openwrt/openwrt/issues/9467>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Martin Kennedy [Sun, 28 Nov 2021 01:59:18 +0000 (20:59 -0500)]
mpc85xx: add support for Extreme Networks WS-AP3825i
Hardware:
- SoC: Freescale P1020
- CPU: 2x e500v2 @ 800MHz
- Flash: 64MiB NOR (1x Intel JS28F512)
- Memory: 256MiB (2x ProMOS DDR3 V73CAG01168RBJ-I9H 1Gb)
- WiFi1: 2.4+5GHz abgn 3x3 (Atheros AR9590)
- Wifi2: 5GHz an+ac 3x3 (Qualcomm Atheros QCA9890)
- ETH: 2x PoE Gigabit Ethernet (2x Atheros AR8035)
- Power: 12V (center-positive barrel) or 48V PoE (active or passive)
- Serial: Cisco-compatible RJ45 next to 12V power socket (115200 baud)
- LED Driver: TI LV164A
- LEDs: (not functioning)
- 2x Power (Green + Orange)
- 4x ETH (ETH1 + ETH2) x (Green + Orange)
- 2x WiFi (WiFi2 + WiFi1)
Installation:
1. Grab the OpenWrt initramfs <openwrt-initramfs-bin>, e.g.
openwrt-mpc85xx-p1020-extreme-networks_ws-ap3825i-initramfs-kernel.bin.
Place it in the root directory of a DHCP+TFTP server, e.g. OpenWrt
`dnsmasq` with configuration `dhcp.server.enable_tftp='1'`.
2. Connect to the serial port and boot the AP with options
e.g. 115200,N,8. Stop autoboot in U-Boot by pressing Enter after
'Scanning JFFS2 FS:' begins, then waiting for the prompt to be
interrupted. Credentials are identical to the one in the APs
interface. By default it is admin / new2day: if these do not work,
follow the OEM's reset procedure using the reset button.
3. Set the bootcmd so the AP can boot OpenWrt by executing:
```uboot
setenv boot_openwrt "cp.b 0xEC000000 0x2000000 0x2000000; interrupts off; bootm start 0x2000000; bootm loados; fdt resize; fdt boardsetup; fdt chosen; bootm prep; bootm go;"
setenv bootcmd "run boot_openwrt"
saveenv
```
If you plan on going back to the vendor firmware - the bootcmd for it
is stored in the boot_flash variable.
4. Load the initramfs image to RAM and boot by executing
```uboot
setenv ipaddr <ipv4 client address>;
setenv serverip <tftp server address>;
tftpboot 0x2000000 <openwrt-initramfs-bin>;
interrupts off;
bootm start 0x2000000;
bootm loados;
fdt resize;
fdt boardsetup;
fdt chosen;
bootm prep;
bootm go;
```
5. Make a backup of the "firmware" partition if you ever wish to go back
to the vendor firmware.
6. Upload the OpenWrt sysupgrade image via SCP to the devices /tmp
folder.
7. Flash OpenWrt using sysupgrade.
```ash
sysupgrade /tmp/<openwrt-sysupgrade-bin>
```
Notes:
- We must step through the `bootm` process manually to avoid fdt
relocation. To explain: the stock U-boot (and stock Linux) are configured
with a very large CONFIG_SYS_BOOTMAPSZ (and the device's stock Linux
kernel is configured to be able to handle it). The U-boot version
predates the check for the `fdt_high` variable, meaning that upon fdt
relocation, the fdt can (and will) be moved to a very high address; the
default appears to be 0x9ffa000. This address is so high that when the
Linux kernel starts reading the fdt at the beginning of the boot process,
it encounters a memory access exception and panics[5]. While it is
possible to reduce the highest address the fdt will be relocated to by
setting `bootm_size`, this also has the side effect of limiting the
amount of RAM the kernel can use[3].
- Because it is not relocated, the flattened device tree needs to be
padded in the build process to guarantee that `fdt resize` has
enough space.
- The primary ethernet MAC address is stored (and set) in U-boot; they are
shimmed into the device tree by 'fdt boardsetup' through the
'local-mac-address' property of the respective ethernet node, so OpenWrt
does not need to set this at runtime. Note that U-boot indexes the
ethernet nodes by alias, which is why the device tree explicitly aliases
ethernet1 to enet2.
- LEDs do not function under OpenWrt. Each of 8 LEDs is connected to an
output of a TI LV164A shift register, which is wired to GPIO lines and
operates through bit-banged SPI. Unfortunately, I am unable to get the
spi-gpio driver to recognize the `led_spi` device tree node at all, as
confirmed by patching in printk messages demonstrating
spi-gpio.c::spi_gpio_probe never runs. It is possible to manually
articulate the shift register by exporting the GPIO lines and stepping
their values through the sysfs.
- Though they do not function under OpenWrt, I have left the pinout details
of the LEDs and shift register in the device tree to represent real
hardware.
- An archive of the u-boot and Linux source for the AP3825i (which is one
device of a range of devices code-named 'CHANTRY') be found here[1].
- The device has an identical case to both the Enterasys WS-AP3725i and
Adtran BSAP-2030[2] (and potentially other Adtran BSAPs). Given that
there is no FCC ID for the board itself (only its WLAN modules), it's
likely these are generic boards, and even that the WS-AP3725i is
identical, with only a change in WLAN card. I have ordered one to confirm
this.
- For additional information: the process of porting the board is
documented in an OpenWrt forum thread[4].
[1]: magnet:?xt=urn:btih:
f5306a5dfd06d42319e4554565429f84dde96bbc
[2]: https://forum.openwrt.org/t/support-for-adtran-bluesocket-bsap-2030/48538
[3]: https://forum.openwrt.org/t/adding-openwrt-support-for-ws-ap3825i/101168/29
[4]: https://forum.openwrt.org/t/adding-openwrt-support-for-ws-ap3825i/101168
[5]: https://forum.openwrt.org/t/adding-openwrt-support-for-ws-ap3825i/101168/26
Tested-by: Martin Kennedy <hurricos@gmail.com>
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
Rosen Penev [Thu, 10 Mar 2022 06:31:14 +0000 (22:31 -0800)]
argp-standalone: fix compilation with Alpine Linux
This package is a C89 one. Add the proper CFLAG to fix compilation.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Brian Norris [Sun, 13 Mar 2022 06:04:30 +0000 (22:04 -0800)]
base-files: Align rootfs_data upgrades to 64KiB on eMMC
Rootfs overlays get created at a ROOTDEV_OVERLAY_ALIGN (64KiB)
alignment after the rootfs, but emmc_do_upgrade() is assuming
it comes at the very next 512-byte sector.
Suggested-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
(move spaces around, mention fstools' libtoolfs)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Martin Schiller [Wed, 16 Mar 2022 14:04:56 +0000 (15:04 +0100)]
openssl: bump to 1.1.1n
This is a bugfix release. Changelog:
*) Fixed a bug in the BN_mod_sqrt() function that can cause it to loop
forever for non-prime moduli. (CVE-2022-0778)
*) Add ciphersuites based on DHE_PSK (RFC 4279) and ECDHE_PSK
(RFC 5489) to the list of ciphersuites providing Perfect Forward
Secrecy as required by SECLEVEL >= 3.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Rodolphe de Saint Léger [Wed, 16 Mar 2022 09:19:30 +0000 (10:19 +0100)]
ramips: add support for Netgear WN3100RPv2
This patch adds support for the Netgear WN3100RPv2
http://www.netgear.com/support/product/wn3100rpv2.aspx
Specifications:
- SoC: MediaTek MT7620A (580MHz, ramips)
- RAM: 32MB DDR
- Storage: 8MB NOR SPI flash
- Wireless: builtin MT7620A, 2x2:2 with u.FL connectors
- Ethernet: 1x100M
- Stock firmware based on OpenWRT Kamikaze
Like the EX2700, the bootloader expects a secondary image signature,
see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577
This device seems to be same hardware as a WN3000RPv3
Flash instructions:
- Use the Netgear WebUI to upgrade to OpenWRT using the factory image
(see note below),
- Use the sysupgrade image for upgrading versions from OpenWRT,
- TFTP recovery procedure can be used to flash the factory image
(preferred method).
Note:
- The WebUI may not reboot automatically, wait at least 5 minutes before
powercycling the device
Flashing using TFTP:
- Set you IP address to 192.168.1.10/24 (no gateway)
- Connect your machine to the Ethernet port
- Power off the device and wait for 10 seconds,
- Hold the reset button and power on the device (do not release reset),
- Hold the reset button until the green light is flashing (Approx. 15s)
- launch tftp, set mode to binary and connect to 192.168.1.1
- put the factory firmware image
- All leds will switch off (like a power off), this is normal
- Wait for the device to reboot in the new OpenWRT image (max 5 mins)
- The first boot will take longer than usual.
- After boot, the Device IP on the ethernet port is 192.168.1.1
Signed-off-by: Rodolphe de Saint Léger <rdesaintleger@gmail.com>
[drop unneeded includes in dts, wrap commit message]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Sungbo Eo [Wed, 16 Mar 2022 14:10:45 +0000 (23:10 +0900)]
Revert "ramips: add support for Netgear WN3000RPv3"
This reverts commit
7bc20cb6143e089fae6ad4b173fc42b55bdbecfe.
It adds support for Netgear WN3100RPv2, but the commit title is wrong.
It will be re-added with the correct title.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Rodolphe de Saint Léger [Wed, 16 Mar 2022 09:19:30 +0000 (10:19 +0100)]
ramips: add support for Netgear WN3000RPv3
This patch adds support for the Netgear WN3100RPv2
http://www.netgear.com/support/product/wn3100rpv2.aspx
Specifications:
- SoC: MediaTek MT7620A (580MHz, ramips)
- RAM: 32MB DDR
- Storage: 8MB NOR SPI flash
- Wireless: builtin MT7620A, 2x2:2 with u.FL connectors
- Ethernet: 1x100M
- Stock firmware based on OpenWRT Kamikaze
Like the EX2700, the bootloader expects a secondary image signature,
see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577
This device seems to be same hardware as a WN3000RPv3
Flash instructions:
- Use the Netgear WebUI to upgrade to OpenWRT using the factory image
(see note below),
- Use the sysupgrade image for upgrading versions from OpenWRT,
- TFTP recovery procedure can be used to flash the factory image
(preferred method).
Note:
- The WebUI may not reboot automatically, wait at least 5 minutes before
powercycling the device
Flashing using TFTP:
- Set you IP address to 192.168.1.10/24 (no gateway)
- Connect your machine to the Ethernet port
- Power off the device and wait for 10 seconds,
- Hold the reset button and power on the device (do not release reset),
- Hold the reset button until the green light is flashing (Approx. 15s)
- launch tftp, set mode to binary and connect to 192.168.1.1
- put the factory firmware image
- All leds will switch off (like a power off), this is normal
- Wait for the device to reboot in the new OpenWRT image (max 5 mins)
- The first boot will take longer than usual.
- After boot, the Device IP on the ethernet port is 192.168.1.1
Signed-off-by: Rodolphe de Saint Léger <rdesaintleger@gmail.com>
[drop unneeded includes in dts, wrap commit message]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Pawel Dembicki [Thu, 17 Feb 2022 23:23:45 +0000 (00:23 +0100)]
ramips: mt7620: Add support for D-Link DWR-961 A1
The DWR-961 A1 Wireless Router is based on the MT7620A SoC.
It's a merge of two Amit boards: DWR-960 with ethernet part
of Lava LR-25G001.
ROMID it's taken from Telenor branded version and it works with tested
device. Images from D-Link site for this router are from DWR-953 and it
have ROMID DLK6E2424001. I don't know if it's mistake on web-site
or if it's will require different image.
Specification:
- MediaTek MT7620A (580 Mhz)
- 128 MB of RAM
- 16 MB of FLASH
- 1x 802.11bgn radio
- 1x 802.11ac radio (MT7612 mpcie card)
- 5x 10/100/1000 Mbps Ethernet: 4xLAN and 1xWAN (QCA8337)
- 2x internal, non-detachable antennas (Wifi 2.4G)
- 3x external, detachable antennas (2x LTE, 1x Wifi 5G)
- 1x LTE modem cat 6
- UART (J5) header on PCB (57600 8n1)
- 13x LED, 2x button
- JBOOT bootloader
Installation:
Apply factory image via http web-gui or JBOOT recovery page
How to revert to OEM firmware:
- push the reset button and turn on the power. Wait until LED start
blinking (~10sec.)
- upload original factory image via JBOOT http (IP: 192.168.123.254)
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Stijn Tintel [Tue, 15 Mar 2022 23:25:08 +0000 (01:25 +0200)]
qoriq: enable I2C in target kernel config
The I2C controller used in QorIQ PPC devices requires the mpc-i2c
driver, which is enabled by the I2C_MPC kernel config symbol. Enable
this and its dependencies in the target kernel config, as is done for
the mpc85xx target.
This fixes missing hwmon, rtc and tpm devices on the M300.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Rafał Miłecki [Tue, 15 Mar 2022 17:42:15 +0000 (18:42 +0100)]
bcm4908: include U-Boot DTB files for ASUS GT-AX6000 & Netgear RAX220
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Tue, 15 Mar 2022 17:41:03 +0000 (18:41 +0100)]
uboot-bcm4908: add BCM4912 build
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Tue, 15 Mar 2022 13:30:20 +0000 (14:30 +0100)]
uboot-bcm4908: update to the latest generic
0625aad74d arm: dts: add ASUS GT-AX6000
6fb1cb624d arm: dts: add Netgear RAXE450 / RAXE550
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Tue, 15 Mar 2022 11:40:40 +0000 (12:40 +0100)]
uboot-bcm4908: use "xxd" from staging_dir
This fixes:
bash: xxd: command not found
on hosts without xxd installed.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Felix Fietkau [Tue, 15 Mar 2022 09:45:38 +0000 (10:45 +0100)]
mt76: update to the latest version
378b638c70c0 mt76: mt7915: fix unused variable with testmode disabled
4f4309542862 mt76: mt7915: only use u32_get_bits with constant value
de06d828a0bf mt76: mt7921: fix injected MPDU transmission to not use HW A-MSDU
c007ba3ec7a9 mt76: mt7915: simplify conditional
64c74dc93f68 mt76: fix dfs state issue with 160 MHz channels
d3471b0d92c1 mt76: mt7615: honor ret from mt7615_mcu_restart in mt7663u_mcu_init
f4c87b32e0e9 mt76: mt7663u: introduce mt7663u_mcu_power_on routine
82de5987af54 mt76: mt7921: fix up the monitor mode
c501df4086e1 mt76: mt7921: use mt76_hw instead of open coding it
594ee03d5a11 mt76: mt7915: fix DFS no radar detection event
d8d2b383a241 mt76: split single ldpc cap bit into bits
0f336fba20fe mt76: mt7921: make mt7921_init_tx_queues static
00a066ce9914 mt76: mt7921: fix xmit-queue dump for usb and sdio
d6d2479568b2 mt76: mt7921: fix mt7921_queues_acq implementation
d17b74420199 mt76: fix monitor mode crash with sdio driver
c374559eae6f mt76: mt7915: allow beaconing on all chains
b219af63b9ce mt76: connac: add 6 GHz support for wtbl and starec configuration
630384cb3246 mt76: mt7915: add 6 GHz support
28ff1bddc7e8 mt76: mt7915: fix eeprom fields of txpower init values
d4b226cc15e7 mt76: mt7915: add txpower init for 6GHz
31e820d4ce4b mt76: mt7921: get rid of mt7921_wait_for_mcu_init declaration
9fee1faf6028 mt76: mt7915: check for devm_pinctrl_get() failure
31a970940b97 mt76: connac: make read-only array ba_range static const
e49af7036bbc mt76: use le32/16_get_bits() whenever possible
0664d39039c2 mt76: fix invalid rssi report
f16fc9d96105 mt76: mt7915: set band1 TGID field in tx descriptor
67ce2708dcef mt76: mt7915: fix beamforming mib stats
6e899abec818 mt76: mt7915: fix phy cap in mt7915_set_stream_he_txbf_caps()
c6780c85cff2 mt76: mt7915: fix typos in comments
aa6eadc09a83 mt76: usb: add req_type to ___mt76u_rr signature
74a519ab8353 mt76: usb: add req_type to ___mt76u_wr signature
2651d2c66cbd mt76: usb: introduce __mt76u_init utility routine
c03e095eee27 mt76: mt7921: disable runtime pm for usb
41085cdcd7e3 mt76: mt7921: update mt7921_skb_add_usb_sdio_hdr to support usb
e700aba6bae3 mt76: mt7921: move mt7921_usb_sdio_tx_prepare_skb in common mac code
056b7f4ebcc6 mt76: mt7921: move mt7921_usb_sdio_tx_complete_skb in common mac code.
0abf682a3def mt76: mt7921: move mt7921_usb_sdio_tx_status_data in mac common code.
b0c60d5252de mt76: mt7921: add mt7921u driver
053668acdaf8 mt76: mt7921: move mt7921_init_hw in a dedicated work
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Philip Prindeville [Tue, 26 Oct 2021 19:47:17 +0000 (13:47 -0600)]
kernel: include CONFIG_KEXEC_SIG in configs
Seeing failure to build because of missing symbols related to provisioning
CONFIG_KEXEC and signed images. Without this, if you set
CONFIG_KERNEL_KEXEC=y and try to build, target/linux will hang at:
scripts/kconfig/conf --syncconfig Kconfig
...
kexec system call (KEXEC) [Y/n/?] y
kexec file based system call (KEXEC_FILE) [Y/n/?] y
Verify kernel signature during kexec_file_load() syscall (KEXEC_SIG) [N/y/?] (NEW)
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Marek Behún [Mon, 14 Mar 2022 17:31:30 +0000 (18:31 +0100)]
kernel: backport DSA patches fixing null-pointer dereference for 5.10
Backport patches
381a730182f1 ("net: dsa: Move VLAN filtering syncing out of dsa_switch_bridge_leave")
108dc8741c20 ("net: dsa: Avoid cross-chip syncing of VLAN filtering")
from upstream (currently in net-next) to fix null-pointer dereference.
Signed-off-by: Marek Behún <kabel@kernel.org>
Petr Štetiar [Fri, 11 Mar 2022 19:56:02 +0000 (20:56 +0100)]
mac80211: headers: fix lockdep_assert_not_held()
LOCK_STATE_HELD define was omitted during backport of
lockdep_assert_not_held() which leads to build failures of kernels with
CONFIG_LOCKDEP=y:
backports-5.15.8-1/backport-include/linux/lockdep.h:16:47: error: 'LOCK_STATE_HELD' undeclared (first use in this function)
Fix it by adding missing LOCK_STATE_HELD define.
References: PR#9373
Reported-by: Oskari Rauta <oskari.rauta@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Michael Pratt [Wed, 8 Sep 2021 21:00:00 +0000 (17:00 -0400)]
ath79: add support for Araknis AN-700-AP-I-AC
FCC ID: 2AG6R-AN700APIAC
Araknis AN-700-AP-I-AC is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+
this board is a Senao device:
the hardware is equivalent to EnGenius EAP1750
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails
**Specification:**
- QCA9558 SOC MIPS 74kc, 2.4 GHz WMAC, 3x3
- QCA9880 WLAN PCI card, 5 GHz, 3x3, 26dBm
- AR8035-A PHY RGMII GbE with PoE+ IN
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM NT5TU32M16
- UART console J10, populated, RX shorted to ground
- 4 antennas 5 dBi, internal omni-directional plates
- 4 LEDs power, 2G, 5G, wps
- 1 button reset
NOTE: all 4 gpio controlled LEDS are viewed through the same lightguide
therefore, the power LED is off for default state
**MAC addresses:**
MAC address labeled as ETH
Only one Vendor MAC address in flash at art 0x0
eth0 ETH *:xb art 0x0
phy1 2.4G *:xc ---
phy0 5GHz *:xd ---
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin at J10
**Installation:**
Method 1: Firmware upgrade page:
(if you cannot access the APs webpage)
factory reset with the reset button
connect ethernet to a computer
OEM webpage at 192.168.20.253
username and password 'araknis'
make a new password, login again...
Navigate to 'File Management' page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm
wait about 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
192.168.20.253
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
Method 1: Serial to load Failsafe webpage (above)
Method 2: delete a checksum from uboot-env
this will make uboot load the failsafe image at next boot
because it will fail the checksum verification of the image
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait a minute
connect to ethernet and navigate to
192.168.20.253
select OEM firmware image and click upgrade
Method 3: backup mtd partitions before upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs-kernel.bin to '
0101A8C0.img'
make available on TFTP server at 192.168.1.101
power board, interrupt boot with serial console
execute `tftpboot` and `bootm 0x81000000`
NOTE: TFTP may not be reliable due to bugged bootloader
set MTU to 600 and try many times
**Format of OEM firmware image:**
The OEM software is built using SDKs from Senao
which is based on a heavily modified version
of Openwrt Kamikaze or Altitude Adjustment.
One of the many modifications is sysupgrade being performed by a custom script.
Images are verified through successful unpackaging, correct filenames
and size requirements for both kernel and rootfs files, and that they
start with the correct magic numbers (first 2 bytes) for the respective headers.
Newer Senao software requires more checks but their script
includes a way to skip them.
The OEM upgrade script is at
/etc/fwupgrade.sh
OKLI kernel loader is required because the OEM software
expects the kernel to be less than 1536k
and the OEM upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied at the PHY side,
using the at803x driver `phy-mode` setting through the DTS.
Therefore, the Ethernet Configuration registers for GMAC0
do not need the bits for RGMII delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Michael Pratt [Wed, 17 Mar 2021 05:07:36 +0000 (01:07 -0400)]
ath79: add support for Araknis AN-500-AP-I-AC
FCC ID: 2AG6R-AN500APIAC
Araknis AN-500-AP-I-AC is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+
this board is a Senao device:
the hardware is equivalent to EnGenius EAP1200
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails
**Specification:**
- QCA9557 SOC MIPS 74kc, 2.4 GHz WMAC, 2x2
- QCA9882 WLAN PCI card 168c:003c, 5 GHz, 2x2, 26dBm
- AR8035-A PHY RGMII GbE with PoE+ IN
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM NT5TU32M16
- UART console J10, populated, RX shorted to ground
- 4 antennas 5 dBi, internal omni-directional plates
- 4 LEDs power, 2G, 5G, wps
- 1 button reset
NOTE: all 4 gpio controlled LEDS are viewed through the same lightguide
therefore, the power LED is off for default state
**MAC addresses:**
MAC address labeled as ETH
Only one Vendor MAC address in flash at art 0x0
eth0 ETH *:e1 art 0x0
phy1 2.4G *:e2 ---
phy0 5GHz *:e3 ---
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin at J10
**Installation:**
Method 1: Firmware upgrade page:
(if you cannot access the APs webpage)
factory reset with the reset button
connect ethernet to a computer
OEM webpage at 192.168.20.253
username and password 'araknis'
make a new password, login again...
Navigate to 'File Management' page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm
wait about 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
192.168.20.253
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
Method 1: Serial to load Failsafe webpage (above)
Method 2: delete a checksum from uboot-env
this will make uboot load the failsafe image at next boot
because it will fail the checksum verification of the image
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait a minute
connect to ethernet and navigate to
192.168.20.253
select OEM firmware image and click upgrade
Method 3: backup mtd partitions before upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs-kernel.bin to '
0101A8C0.img'
make available on TFTP server at 192.168.1.101
power board, interrupt boot with serial console
execute `tftpboot` and `bootm 0x81000000`
NOTE: TFTP may not be reliable due to bugged bootloader
set MTU to 600 and try many times
**Format of OEM firmware image:**
The OEM software is built using SDKs from Senao
which is based on a heavily modified version
of Openwrt Kamikaze or Altitude Adjustment.
One of the many modifications is sysupgrade being performed by a custom script.
Images are verified through successful unpackaging, correct filenames
and size requirements for both kernel and rootfs files, and that they
start with the correct magic numbers (first 2 bytes) for the respective headers.
Newer Senao software requires more checks but their script
includes a way to skip them.
The OEM upgrade script is at
/etc/fwupgrade.sh
OKLI kernel loader is required because the OEM software
expects the kernel to be less than 1536k
and the OEM upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied at the PHY side,
using the at803x driver `phy-mode` setting through the DTS.
Therefore, the Ethernet Configuration registers for GMAC0
do not need the bits for RGMII delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Michael Pratt [Fri, 26 Mar 2021 06:12:26 +0000 (02:12 -0400)]
ath79: add support for Araknis AN-300-AP-I-N
FCC ID: U2M-AN300APIN
Araknis AN-300-AP-I-N is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+
this board is a Senao device:
the hardware is equivalent to EnGenius EWS310AP
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails
**Specification:**
- AR9344 SOC MIPS 74kc, 2.4 GHz WMAC, 2x2
- AR9382 WLAN PCI on-board 168c:0030, 5 GHz, 2x2
- AR8035-A PHY RGMII GbE with PoE+ IN
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM 1839ZFG V59C1512164QFJ25
- UART console J10, populated, RX shorted to ground
- 4 antennas 5 dBi, internal omni-directional plates
- 4 LEDs power, 2G, 5G, wps
- 1 button reset
NOTE: all 4 gpio controlled LEDS are viewed through the same lightguide
therefore, the power LED is off for default state
**MAC addresses:**
MAC address labeled as ETH
Only one Vendor MAC address in flash at art 0x0
eth0 ETH *:7d art 0x0
phy1 2.4G *:7e ---
phy0 5GHz *:7f ---
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin at J10
**Installation:**
Method 1: Firmware upgrade page:
(if you cannot access the APs webpage)
factory reset with the reset button
connect ethernet to a computer
OEM webpage at 192.168.20.253
username and password 'araknis'
make a new password, login again...
Navigate to 'File Management' page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm
wait about 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
192.168.20.253
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
Method 1: Serial to load Failsafe webpage (above)
Method 2: delete a checksum from uboot-env
this will make uboot load the failsafe image at next boot
because it will fail the checksum verification of the image
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait a minute
connect to ethernet and navigate to
192.168.20.253
select OEM firmware image and click upgrade
Method 3: backup mtd partitions before upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs-kernel.bin to '
0101A8C0.img'
make available on TFTP server at 192.168.1.101
power board, interrupt boot with serial console
execute `tftpboot` and `bootm 0x81000000`
NOTE: TFTP may not be reliable due to bugged bootloader
set MTU to 600 and try many times
**Format of OEM firmware image:**
The OEM software is built using SDKs from Senao
which is based on a heavily modified version
of Openwrt Kamikaze or Altitude Adjustment.
One of the many modifications is sysupgrade being performed by a custom script.
Images are verified through successful unpackaging, correct filenames
and size requirements for both kernel and rootfs files, and that they
start with the correct magic numbers (first 2 bytes) for the respective headers.
Newer Senao software requires more checks but their script
includes a way to skip them.
The OEM upgrade script is at
/etc/fwupgrade.sh
OKLI kernel loader is required because the OEM software
expects the kernel to be less than 1536k
and the OEM upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied at the PHY side,
using the at803x driver `phy-mode` setting through the DTS.
Therefore, the Ethernet Configuration registers for GMAC0
do not need the bits for RGMII delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Michael Pratt [Wed, 17 Mar 2021 23:07:46 +0000 (19:07 -0400)]
ath79: improve factory.bin for some Senao devices
Some boards with firmware made with Senao SDK based on Linux 3.3
have the following lines in the OEM upgrade script at
/etc/fwupgrade.sh
local append=""
local CONF_TAR="/tmp/sysupgrade.tgz"
[ -f "$CONF_TAR" ] && append="-j $CONF_TAR"
and
\# check FWINFO filename
[ -z $(ls FWINFO* | grep -i ${modelname}) ] && errcode="1"
This addition also prevents needing to factory reset after flashing
for some boards that also have these lines in the script
\# Support downgrade but do default (Smart v2.x.x.x -> senaowrt v1.x.x.x)
[ $(ls FWINFO* | grep -i ${modelname} | cut -d "-" -f4 | cut -c 2) -lt 2 ] && append=""
Signed-off-by: Michael Pratt <mcpratt@pm.me>
INAGAKI Hiroshi [Wed, 9 Mar 2022 14:31:00 +0000 (23:31 +0900)]
realtek: add support for Panasonic Switch-M8eG PN28080K
Panasonic Switch-M8eG PN28080K is a 8 + 1 port gigabit switch, based on
RTL8380M.
Specification:
- SoC : Realtek RTL8380M
- RAM : DDR3 128 MiB (Winbond W631GG8KB-15)
- Flash : SPI-NOR 32 MiB (Macronix MX25L25635FMI-10G)
- Ethernet : 10/100/1000 Mbps x8 + 1
- port 1-8 : TP, RTL8218B (SoC)
- port 9 : SFP, RTL8380M (SoC)
- LEDs/Keys : 7x / 1x
- UART : RS-232 port on the front panel (connector: RJ-45)
- 3:TX, 4:GND, 5:GND, 6:RX (pin number: RJ-45)
- 9600n8
- Power : 100-240 VAC, 50/60 Hz, 0.5 A
- Plug : IEC 60320-C13
- Stock OS : VxWorks based
Flash instruction using initramfs image:
1. Prepare the TFTP server with the IP address 192.168.1.111
2. Rename the OpenWrt initramfs image to "
0101A8C0.img" and place it to
the TFTP directory
3. Download the official upgrading firmware (ex: pn28080k_v30000.rom)
and place it to the TFTP directory
4. Boot M8eG and interrupt the U-Boot with Ctrl + C keys
5. Execute the following commands and boot with the OpenWrt initramfs
image
rtk network on
tftpboot 0x81000000
bootm
6. Backup mtdblock files to the computer by scp or anything and reboot
7. Interrupt the U-Boot and execute the following commands to re-create
filesystem in the flash
ffsmount c:/
ffsfmt c:/
this step takes a long time, about ~ 4 mins
8. Execute the following commands to put the official images to the
filesystem
updatert <official image>
example:
updatert pn28080k_v30000.rom
this step takes about ~ 40 secs
9. Set the environment variables of the U-Boot by the following commands
setenv loadaddr 0xb4e00000
setenv bootcmd bootm
saveenv
10: Download the OpenWrt initramfs image and boot with it
tftpboot 0x81000000
0101A8C0.img
bootm
11: On the initramfs image, download the sysupgrade image and perform
sysupgrade with it
sysupgrade <imagename>
12: Wait ~ 120 seconds to complete flashing
Note:
- "Switch-M8eG" is a model name, and "PN28080K" is a model number.
Switch-M8eG has an another (old) model number ("PN28080"), it's not a
Realtek based hardware.
- Switch-M8eG has a "POWER" LED (Green), but it's not connected to any
GPIO pin.
- The U-Boot checks the runtime images in the flash when booting and
fails to execute anything in "bootcmd" variable if the images are not
exsisting.
- A filesystem is formed in the flash (0x100000-0x1DFFFFF) on the stock
firmware and it includes the stock images, configuration files and
checksum files. It's unknown format, can't be managed on the OpenWrt.
To get the enough space for OpenWrt, move the filesystem to the head
of "fs_reserved" partition by execution of "ffsfmt" and "updatert".
- On the other devices in the same series of Switch-M8eG PN28080K, the
INT pin on the PCA9555 is not connected to anywhere.
Back to the stock firmware:
1. Delete "loadaddr" variable and set "bootcmd" to the original value
on U-Boot:
setenv loadaddr
setenv bootcmd 'bootm 0x81000000'
on OpenWrt:
fw_setenv loadaddr
fw_setenv bootcmd 'bootm 0x81000000'
2. Perform reset or reboot
on U-Boot:
reset
on OpenWrt:
reboot
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Reviewed-by: Sander Vanheule <sander@svanheule.net>
INAGAKI Hiroshi [Wed, 9 Mar 2022 14:30:59 +0000 (23:30 +0900)]
realtek: enable pca953x driver for rtl838x subtarget
The system status LED on Panasonic Switch-M8eG PN28080K is connected to
a PCA9539PW. To use the LED as a status LED of OpenWrt while booting,
enable the pca953x driver and built-in to the kernel.
Also enable CONFIG_GPIO_PCA953X_IRQ to use interrupt via RTL83xx GPIO.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Acked-by: Sander Vanheule <sander@svanheule.net>
Martin Kennedy [Sat, 5 Mar 2022 19:02:36 +0000 (14:02 -0500)]
realtek: add ZyXEL GS1900-24 v1 support
The ZyXEL GS1900-24 v1 is a 24 port switch with two SFP ports, similar to
the other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-24 v1
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB
* RAM: Winbond W9751G8KB-25 64 MiB DDR2 SDRAM
* Ethernet: 24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps
* LEDs:
* 1 PWR LED (green, not configurable)
* 1 SYS LED (green, configurable)
* 24 ethernet port link/activity LEDs (green, SoC controlled)
* 2 SFP status/activity LEDs (green, SoC controlled)
* Buttons:
* 1 "RESET" button on front panel (soft reset)
* 1 button ('SW1') behind right hex grate (hardwired power-off)
* Power: 120-240V AC C13
* UART: Internal populated 10-pin header ('J5') providing RS232;
connected to SoC UART through a SIPEX 3232EC for voltage
level shifting.
* 'J5' RS232 Pinout (dot as pin 1):
2) SoC RXD
3) GND
10) SoC TXD
Serial connection parameters: 115200 8N1.
Installation
------------
OEM upgrade method:
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware > Management
* If "Active Image" has the first option selected, OpenWrt will need to be
flashed to the "Active" partition. If the second option is selected,
OpenWrt will need to be flashed to the "Backup" partition.
* Navigate to Maintenance > Firmware > Upload
* Upload the openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-initramfs-kernel.bin
file by your preferred method to the previously determined partition.
When prompted, select to boot from the newly flashed image, and reboot
the switch.
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-squashfs-sysupgrade.bin
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs
image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
> Since the GS1900-24 v1 is a dual-partition device, you want to keep the
OEM firmware on the backup partition for the time being. OpenWrt can
only be installed in the first partition anyway (hardcoded in the
DTS). To ensure we are set to boot from the first partition, issue the
following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x81f00000 192.168.1.10:openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-squashfs-sysupgrade.bin
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
Tianling Shen [Wed, 9 Mar 2022 02:35:04 +0000 (10:35 +0800)]
kernel/modules: add kmod-inet-diag package
Add option to compile kmod-inet-diag, support for INET (TCP, DCCP, etc)
socket monitoring interface used by native Linux tools such as ss.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
John Audia [Tue, 8 Mar 2022 22:01:48 +0000 (17:01 -0500)]
kernel: bump 5.10 to 5.10.104
All patches automatically rebased.
Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200
Signed-off-by: John Audia <graysky@archlinux.us>
Rosen Penev [Mon, 7 Mar 2022 04:46:22 +0000 (20:46 -0800)]
tools/ccache: update to 4.6
Full changelog: https://ccache.dev/releasenotes.html#_ccache_4_6
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Mon, 7 Mar 2022 04:53:47 +0000 (20:53 -0800)]
tools/fakeroot: update to 1.28
Refreshed patches.
Upstream says there's only a bugfix for GNU Hurd.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Mon, 7 Mar 2022 04:30:53 +0000 (20:30 -0800)]
tools/cmake: update to 3.22.3
Seems to be mostly pthread fixes.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Mon, 7 Mar 2022 05:02:33 +0000 (21:02 -0800)]
tools/mtools: update to 4.0.38
No real changelog available.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Etienne Champetier [Sun, 13 Mar 2022 05:24:13 +0000 (00:24 -0500)]
iptables: backport missing init_extensions6() calls
This fixes ip6tables-nft no being able to use built-in
extensions like icmp6.
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
Florian Eckert [Wed, 2 Mar 2022 08:42:52 +0000 (09:42 +0100)]
ipset: add backport patch for IPv6 nftables ipset-translation
When porting mwan3 from iptables to nftables I tried the new translation
tool for ipset ipset-translate. I noticed that no IPv6 ipset can be
created with the tool. I have reported the problem to the upstream
project and the following patch fixes the problem.
Until this upsream is included in a new release, this patch should be
used in Openwrt.
https://lore.kernel.org/netfilter-devel/
20220228190217.
2256371-1-pablo@netfilter.org/T/#m09cc3cb738f2e42024c7aecf5b7240d9f6bbc19c
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Rosen Penev [Sat, 12 Mar 2022 22:58:10 +0000 (14:58 -0800)]
tools/expat: enable DTD
Fixes gdb usage, which depends on it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Mon, 7 Mar 2022 04:58:29 +0000 (20:58 -0800)]
tools/expat: update to 2.4.7
Mostly a bug fix to the bug fix to CVE-2022-25236
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Joe Mullally [Tue, 8 Mar 2022 19:33:37 +0000 (19:33 +0000)]
ramips: Apply pinctrl DTS changes to TL-WPA8631P
Applies changes from
7774b86019 to new device committed later. Fix some
whitespace in the DTS. Use standard model name format in DTS.
Fixes: 6c743c3006f9 ("ramips: Add support for TP-Link TL-WPA8631P v3")
Signed-off-by: Joe Mullally <jwmullally@gmail.com>
Reported-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Sven Schwermer [Wed, 9 Mar 2022 08:46:41 +0000 (09:46 +0100)]
ath79: Add LED labels for Airtight C-75
Keep labels since OpenWrt userland tooling (get_dt_led) depends on them
to find the LED instances referenced by the led-* aliases.
The label for the amber power LED was removed in
4eefdc7adb.
Signed-off-by: Sven Schwermer <sven@svenschwermer.de>
Chukun Pan [Mon, 10 Jan 2022 04:28:40 +0000 (12:28 +0800)]
ramips: update WLAN MAC address of JCG Y2
MAC addresses on OEM firmware:
04:xx:xx:xx:xx:c8 factory 0x4 wlan2g
06:xx:xx:xx:xx:c8 [not on flash] wlan5g
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Chukun Pan [Sun, 9 Jan 2022 04:16:06 +0000 (12:16 +0800)]
ramips: update WLAN MAC address of Phicomm K2P
The wireless mac address difference of this machine is similar
to that of D-Link DIR-853-R1, so use the same practice.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Dawsen Gao [Sat, 12 Feb 2022 02:21:21 +0000 (10:21 +0800)]
ramips: Add support for Dual-Q H721
Dual-Q H721 is a router platform board, it is the smaller model of
the U7621-06.
The device has the following specifications:
MT7621AT (880 MHz)
256 of RAM (DDR3)
16 MB of FLASH (MX25l12805d SPI)
5x 1 Gbps Ethernet (MT7621 built-in switch)
1x M.2 (NGFF) 3.7V 3A max for 5G M.2 Modem work at USB3.0 mode
1x Minipcie 3.7V 3A max for LTE Modem work at USB2.0 Mode
2x Minipcie for WIFI card
4x Lan+1x Wan 10/100M/1000M RJ45 port
14x LEDs (1x GPIO-controlled)
1x reset button
1x UART header (4-pins)
1x mico SD-card reader
1x DC jack for main power (5~27 V)
The following has been tested and is working:
Ethernet switch
miniPCIe slots (tested with Wi-Fi cards and LTE modem cards)
miniSIM slot (works with normal size simcard)
sysupgrade
reset button
micro SD-card reader
Installation:
This board has no locked down bootloader. The seller can be asked to
install openwrt, so upgrades are standard sysupgrade method.
Recovery:
This board contains a Chinese, closed-source bootloader called Breed
(Boot and Recovery Environment for Embedded Devices). Breed supports web
recovery and to enter it, you keep the reset button pressed for around
5 seconds during boot. Your machine will be assigned an IP through DHCP
and the router will use IP address 192.168.1.1. The recovery website is
in Chinese, but is easy to use. Click on the second item in the list to
access the recovery page, then the second item on the next page is where
you select the firmware. In order to start the recovery, you click the
button at the bottom.
Signed-off-by: Dawsen Gao <dawsen_gao@163.com>
[change author name (used SoB one), add ethernet pinctrl,
apply sorting to device recipe]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Rafał Miłecki [Tue, 1 Mar 2022 17:46:27 +0000 (18:46 +0100)]
base-files: call "sync" after initial setup
OpenWrt uses a lot of (b)ash scripts for initial setup. This isn't the
best solution as they almost never consider syncing files / data. Still
this is what we have and we need to try living with it.
Without proper syncing OpenWrt can easily get into an inconsistent state
on power cut. It's because:
1. Actual (flash) inode and data writes are not synchronized
2. Data writeback can take up to 30 seconds (dirty_expire_centisecs)
3. ubifs adds extra 5 seconds (dirty_writeback_centisecs) "delay"
Some possible cases (examples) for new files:
1. Power cut during 5 seconds after write() can result in all data loss
2. Power cut happening between 5 and 35 seconds after write() can result
in empty file (inode flushed after 5 seconds, data flush queued)
Above affects e.g. uci-defaults. After executing some migration script
it may get deleted (whited out) without generated data getting actually
written. Power cut will result in missing data and deleted file.
There are three ways of dealing with that:
1. Rewriting all user-space init to proper C with syncs
2. Trying bash hacks (like creating tmp files & moving them)
3. Adding sync and hoping for no power cut during critical section
This change introduces the last solution that is the simplest. It
reduces time during which things may go wrong from ~35 seconds to
probably less than a second. Of course it applies only to IO operations
performed before /etc/init.d/boot . It's probably the stage when the
most new files get created.
All later changes are usually done using smarter C apps (e.g. busybox or
uci) that creates tmp files and uses rename() that is expected to be
atomic.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Daniel Golle [Sat, 12 Mar 2022 11:07:27 +0000 (11:07 +0000)]
uqmi: update to git HEAD
44dd095 uqmi: corrected too short received SMS
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Lech Perczak [Sat, 12 Mar 2022 00:50:53 +0000 (01:50 +0100)]
uqmi: set CID during 'query-data-status' operation
Modems used in ZTE mobile broadband routers require to query the data
session status using the same CID as one used to establish the session,
otherwise they will report the session as "disconnected" despite
reporting correct PDH in previous step. Without this change, IPv6
connection on these modems doesn't establish properly. In IPv4 this bug
is present as well, but for some reason querying of IPv4 status works
using temporary CID, this however seems noncompliant with QMI
specifications, so fix it as well.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Rafał Miłecki [Fri, 4 Mar 2022 08:39:05 +0000 (09:39 +0100)]
bcm4908: include U-Boot in images
This is a step forward in adding support for devices with U-Boot.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Fri, 4 Mar 2022 08:39:04 +0000 (09:39 +0100)]
uboot-bcm4908: add package with BCM4908 U-Boot
New BCM4908 devices come with U-Boot instead of CFE. Firmwares for such
devices has to include U-Boot.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Piotr Dymacz [Thu, 10 Mar 2022 22:29:21 +0000 (23:29 +0100)]
imx: fix USB support
The ChipIdea USB kernel driver gained support for disabling glue drivers
in 5.8, see upstream commmit:
95caa2ae70fd ("usb: chipidea: allow
disabling glue drivers if EMBEDDED").
This enables 'CONFIG_USB_CHIPIDEA_IMX' in the 'imx' target kernel config
which brings back USB support.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Matthias Schiffer [Thu, 10 Mar 2022 22:24:10 +0000 (23:24 +0100)]
x86: legacy: enable pata_sis driver
This driver is needed to boot from CompactFlash on the Siemens Futro S400.
The device has an AMD NX1500 CPU, which seems to be unsupported by the
geode subtarget, so it must use legacy.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Daniel Golle [Thu, 10 Mar 2022 17:53:01 +0000 (17:53 +0000)]
kernel: wwan: add MeigLink SLM750 modem support
Add patch found in Teltonika RUT9_R_00.07.01.4 GPL SDK download[1]
adding USB IDs of the MeigLink SLM750 to the relevant kernel drivers.
Newer versions of Teltonika's 2G/3G/4G RUT9XX WWAN router series come
with this kind of modem.
[1]: https://wiki.teltonika-networks.com/view/GPL
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Yousong Zhou [Wed, 9 Mar 2022 05:00:42 +0000 (13:00 +0800)]
iptables: add iptables-mod-socket
Previously libxt_socket.so was included in iptables-mod-tproxy. It was
missed out when trying to make kmod-ipt-socket and kmod-ipt-tproxy
separate packages
Fixes: 4f443c88 ("netfilter: separate packages for kmod-ipt-socket and kmod-ipt-tproxy")
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Paul Spooren [Wed, 9 Mar 2022 12:30:21 +0000 (13:30 +0100)]
CI: move logs/ to GITHUB_WORKSPACE
Artifacts can only be uploaded from inside the GITHUB_WORKSPACE. While
the Linux CI jobs run inside that per default, a special case-sensitive
mount outside the GITHUB_WORKSPACE is used for macOS builds.
To make log artifacts work for both macOS and Linux, move logs/ folder
to GITHUB_WORKSPACE on failures.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Rui Salvaterra [Wed, 9 Feb 2022 15:18:45 +0000 (15:18 +0000)]
toolchain: binutils: add support for version 2.38
While at it, also fix the download.xs4all.nl and add ftp.gnu.org to the GNU
mirrors, as it seems to be updated faster.
Deleted (upstreamed):
600-Close_the_file_descriptor.patch [1]
[1] https://sourceware.org/git/?p=binutils-gdb.git;a=commit;h=
5a98fb7513b559e20dfebdbaa2a471afda3b4742
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Dmitry Chigiryov [Fri, 25 Feb 2022 09:41:12 +0000 (12:41 +0300)]
ramips: allow USB power control on TP-Link MR3020v3
By switching EPHY_LED4_N_JTRST_N from EPHY_LED4_N to GPIO#39
we can control USB port power an all current revisions of MR3020v3.
It was not a thing on some first revisions, pin was unused.
But for now on all current MR3020v3 boards EPHY_LED4_N_JTRST_N pin
is connected to USB power key.
Also it was not used as EPHY indicator on any revision of the board.
Signed-off-by: Dmitry Chigiryov <dmitry.chigiryov@ya.ru>
[changed author address (used SoB one)]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Sungbo Eo [Thu, 24 Feb 2022 14:17:45 +0000 (23:17 +0900)]
ramips: fix DEVICE_VENDOR for unbranded devices
In commit
ee66fe4ea9a6 ("ramips: convert DEVICE_TITLE to new variables"),
DEVICE_VENDOR of some unbranded devices were set incorrectly:
* WR512-3GN is not a dev board from Ralink.
* "XDX-RN502J" is the whole model name and should be not split.
This patch sets their DEVICE_VENDOR to "Unbranded", and changes their DTS
model properties accordingly.
Ref:
d0bf15f23595 ("ramips: add support for A5-V11 board (resubmit)")
Ref:
9085b05d9e71 ("ramips: rt305x: support for wr512-3gn-like routers")
Ref:
0e486d2fd297 ("ramips: add support for unbranded XDX-RN502J board")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Kim Namu [Wed, 23 Feb 2022 15:14:37 +0000 (00:14 +0900)]
ramips: mt7621: add support for Zbtlink ZBT-WG1608
Zbtlink ZBT-WG1608 is a Wi-Fi router intendent to use with WWAN (4G/5G)
modems.
Specifications:
* SoC: MediaTek MT7621A
* RAM: 256/512 MiB
* Flash: 16/32 MiB (SPI NOR)
* Wi-Fi:
* MediaTek MT7603E : 2.4Ghz
* MediaTek MT7613BE : 5Ghz
* Ethernet: 10/100/1000 Mbps Ethernet x5 ports (4xLAN + WAN)
* M.2: 1x slot with USB&SIM
* EM7455/EM12-G/EM160R/RM500Q-AE
* USB: 1x 3.0 Type-A port
* External storage: 1x microSD (SDXC) slot
* UART: console (115200 baud)
* LED:
* 1 power indicator
* 1 WLAN 2.4G controlled (wlan 2G)
* 3 SoC controlled (wlan 5G, wwan, internet)
* 5 per Eth phy (4xLAN + WAN)
MAC Addresses:
* LAN : f8:5e:3c:xx:xx:e0 (Factory, 0xe000 (hex))
* WAN : f8:5e:3c:xx:xx:e1 (Factory, 0xe006 (hex))
* 2.4 GHz: f8:5e:3c:xx:xx:de (Factory, 0x0004 (hex))
* 5 GHz : f8:5e:3c:xx:xx:df (Factory, 0x8004 (hex))
Installation:
* Vendor's firmware is OpenWrt (LEDE) based, so the sysupgrade image can
be directly used to install OpenWrt. Firmware must be upgraded using the
'force' and 'do not save configuration' command line options (or
correspondig web interface checkboxes) since the vendor firmware is from
the pre-DSA era.
Recovery Mode:
* Press reset button, power up the device, wait for about 10sec.
* Upload sysupgrade image through the firmware recovery mode web page at
192.168.1.1.
Signed-off-by: Kim Namu <namu@theseed.io>
Ray Wang [Thu, 10 Feb 2022 15:16:05 +0000 (23:16 +0800)]
ramips: add support for Asus RT-AC1200
Asus RT-AC1200 is a 2.4/5GHz dual band AC router,
based on MediaTek MT7628AN.
Specification:
* SoC: MT7628AN
* RAM: DDR2 64 MiB
* Flash: 16 MiB NOR (W25Q128BV)
* Wi-Fi:
* 2.4GHz: SoC Built-in
* 5GHz: MT7612EN
* Ethernet: 5x 100Mbps
* Switch: SoC built-in
* USB: 1x 2.0
Flash Layout:
0x0000000-0x0030000 : "bootloader"
0x0030000-0x0040000 : "nvram"
0x0040000-0x0050000 : "factory"
0x0050000-0x1000000 : "firmware"
MAC address:
LAN: factory 0x28
WAN: factory 0x22
2.4G: factory 0x4
5G: factory 0x8004
Installation via **recovery** mode:
1. Download the Asus recovery firmware (windows) tool from
http://dlcdnet.asus.com/pub/ASUS/LiveUpdate/Release/Wireless/Rescue.zip
2. Set your ethernet IP manually 192.168.1.5 / 255.255.255.0 with NO
gateway.
3. Plug in your ethernet to LAN port 1 on the router.
4. Load up the recovery software with the firmware file, but don't press
"Upload" yet.
5. Plug in the router to power WHILE HOLDING the reset button in. While
CONTINUING to hold the button, select "Upload" Continue to hold the
reset button in until it finishes and verifies!
6. If that doesn't work try pressing "Upload" first just before you do
step 5. At some point while holding reset the rescue tool will finally
detect and upload the firmware. That's when you can let go of the
reset button.
7. The router will reboot and not much will happen. Wait a minute or 2.
8. Power off and on the router again. Voila. Set everything your Ethernet
IP back to DHCP (automatically) and you're good to go.
Revert to stock firmware:
1. Install stock image via recovery mode.
Tested-by: Ivan Pavlov <AuthorReflex@gmail.com>
Signed-off-by: Ray Wang <raywang777@foxmail.com>
Sungbo Eo [Sat, 12 Feb 2022 08:01:31 +0000 (17:01 +0900)]
tools: zip: make encrypted archives reproducible
Zip always try to generate new encryption header depending on execution
time and process id, which is far from being reproducible. This commit
changes the zip srand() seed to a predictable value to generate
reproducible random bytes for the encryption header. This will compromise
the goal of secure archive encryption, but it would not be a big problem
for our purpose.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Sungbo Eo [Sat, 12 Feb 2022 08:01:31 +0000 (17:01 +0900)]
tools: zip: fetch SOURCE_DATE_EPOCH directly
Remove "--mtime" option introduced in commit
18c9faa03211 ("tools: zip:
add option for reproducible archives") and instead fetch SOURCE_DATE_EPOCH
environment variable directly in the code.
Ref: https://sourceforge.net/p/infozip/patches/25/
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Sungbo Eo [Sat, 12 Feb 2022 08:01:31 +0000 (17:01 +0900)]
build: image: use UTC for zip timestamp
Zip uses DOS timestamp for mtime which is stored in local time and hence
depends on the timezone of the build system. Force zip to use UTC timezone
to make image builds more reproducible.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Birger Koblitz [Mon, 7 Mar 2022 18:50:29 +0000 (19:50 +0100)]
ramips: add support for Renkforce WS-WN530HP3-A
This adds support for the Renkforce WS-WN530HP3-A ceiling-
mountable Wireless Access Point, which is powered over PoE.
Hardware:
- SoC: Mediatek MT7621DAT
- RAM: 128MiB on SoC
- Flash: 16MiB GigaDevice GD25Q128C
- 2.4Ghz Wifi: Mediatek MT603EN
- 5GHz Wifi: MT613BEN
- Ethernet:
- 1x 1GBit WAN port, passive PoE capable
- 2x 1GBit LAN ports
LEDs: 1x Bi-Color LED (red/blue)
Buttons: 1x Reset Button, 1x Power Button
Installation:
Power on the access point and immedately press the reset
button for 10 seconds. Connect web-browser to 192.168.10.1
and upload sysupgrade image. Flash uploaded image and wait
about 2 minutes for reboot.
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [fixed SoB]
Jeffery To [Sun, 6 Mar 2022 14:47:20 +0000 (22:47 +0800)]
ath79: fix button labels for WZR-HP-AG300H and WZR-600DHP
These were present in ar71xx but overlooked when porting to ath79.
Fixes: 480bf2827392 ("ath79: add support for Buffalo WZR-HP-AG300H")
Signed-off-by: Jeffery To <jeffery.to@gmail.com>
Thibaut VARÈNE [Mon, 28 Feb 2022 10:34:43 +0000 (11:34 +0100)]
ath79: add support for MikroTik RouterBOARD mAP lite
The MikroTik RouterBOARD mAPL-2nd (sold as mAP Lite) is a small
2.4 GHz 802.11b/g/n PoE-capable AP.
See https://mikrotik.com/product/RBmAPL-2nD for more info.
Specifications:
- SoC: Qualcomm Atheros QCA9533
- RAM: 64 MB
- Storage: 16 MB NOR
- Wireless: Atheros AR9531 (SoC) 802.11b/g/n 2x2:2, 1.5 dBi antenna
- Ethernet: Atheros AR8229 (SoC), 1x 10/100 port, 802.3af/at PoE in
- 4 user-controllable LEDs:
· 1x power (green)
· 1x user (green)
· 1x lan (green)
· 1x wlan (green)
Flashing:
TFTP boot initramfs image and then perform sysupgrade. Follow common
MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.
Note: following
781d4bfb397cdd12ee0151eb66c577f470e3377d
The network setup avoids using the integrated switch and connects the
single Ethernet port directly. This way, link speed (10/100 Mbps) is
properly reported by eth0.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Hannu Nyman [Sun, 6 Mar 2022 09:56:15 +0000 (11:56 +0200)]
ipq806x: provide ramoops for R7800/XR500 by default
Add kmod-ramoops to the default set of device packages in
R7800 and XR500, so that the ramoops kernel crash logs
are provided by default for these routers.
The capability was earlier defined by
97158fe1 and
cf346dfa,
but the feature was not yet turned on by default.
The possible kernel crashes are stored into /sys/fs/pstore/*
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Sven Schwermer [Mon, 7 Mar 2022 21:08:32 +0000 (22:08 +0100)]
ath79: Add green power LED to Airtight C-75
In addition to the missing green LED definition, the polarity of the
amber power LED was incorrect which is fixed here.
Signed-off-by: Sven Schwermer <sven@svenschwermer.de>
Aleksander Jan Bajkowski [Sat, 5 Mar 2022 11:54:48 +0000 (12:54 +0100)]
lantiq: xrx200: fix use after free bug
The skb->len field is read after the packet is sent to the network
stack. In the meantime, skb can be freed. This patch fixes this bug.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
INAGAKI Hiroshi [Sun, 18 Apr 2021 01:23:09 +0000 (10:23 +0900)]
uboot-envtools: add support for I-O DATA BSH-G24MB
This patch adds the device-specific configuration to u-boot-envtools for
I-O DATA BSH-G24MB switch.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
INAGAKI Hiroshi [Sat, 17 Apr 2021 01:10:27 +0000 (10:10 +0900)]
realtek: add support for I-O DATA BSH-G24MB
I-O DATA BSH-G24MB is a 24 port gigabit switch, based on RTL8382M.
Specification:
- SoC : Realtek RTL8382M
- RAM : DDR2 128 MiB (Nanya NT5TU128M8HE-AC)
- Flash : SPI-NOR 16 MiB (Macronix MX25L12835FM2I-10G)
- Ethernet : 10/100/1000 Mbps x24
- port 1-8 : RTL8218B
- port 9-16 : RTL8218B (SoC)
- port 17-24 : RTL8218B
- LEDs/Keys : 2x, 1x
- UART : pin header on PCB
- JP2: 3.3V, TX, RX, GND from rear side
- 115200n8
- Power : 100 VAC, 50/60 Hz
- Plug : IEC 60320-C13
Flash instruction using sysupgrade image:
1. Boot BSH-G24MB normally
2. Connect BSH-G24MB to the DHCP enabled network
3. Find the device's IP address and open the WebUI and login
Note: by default, the device obtains IP address from DHCP server of
the network
4. Open firmware update page ("ファームウェア アップデート")
5. Rename the OpenWrt sysupgrade image to "bsh-g24mb_v100.image" and
select it
6. Press apply ("適用") button to perform update
7. Wait ~150 seconds to complete flashing
Note:
- BSH-G24MB has a power-related LED ("電源"), but it's not connected to
the GPIO of the SoC or RTL8231 and cannot be controlled. Instead of
it, use system status LED on other than running-state.
- "sys_loop" LED indicates system status and loop-detection status in
stock firmware.
- BSH-G24MB has 2x os-image partitions named as "RUNTIME"/"RUNTIME2" in
16 MiB SPI-NOR flash and the size of image per partition is only
6848 KiB. The secondary image is never used on stock firmware, so also
use it on OpenWrt to get more space.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Josef Schlehofer [Sat, 5 Mar 2022 23:16:27 +0000 (00:16 +0100)]
nftables: update to version 1.0.2
Changelog:
https://lwn.net/ml/netdev/YhO5Pn+6+dgAgSd9@salvia/
Patches:
removed:
- 001-parser-allow-quoted-string-in-flowtable_expr_member:
it is now part of upstream release [1]
added:
- 001-examples-compile-with-make-check.patch:
backported from [2], it fixes:
nft-json-file.c:3:10: fatal error: nftables/libnftables.h: No such file or directory
3 | #include <nftables/libnftables.h>
| ^~~~~~~~~~~~~~~~~~~~~~~~
compilation terminated.
[1] https://git.netfilter.org/nftables/commit/?h=v1.0.2&id=
07af4429241c9832a613cb8620331ac54257d9df
[2] https://git.netfilter.org/nftables/commit/?id=
18a08fb7f0443f8bde83393bd6f69e23a04246b3
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Hauke Mehrtens [Sun, 6 Mar 2022 20:44:06 +0000 (21:44 +0100)]
linux-firmware: Update to version
20220209
This switches the iwlwifi-firmware-ax200 file to API version 66, this is
the most recent version supported by our driver.
The following files used in OpenWrt changed:
amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_dmcub.bin
ar3k-firmware/lib/firmware/qca/nvm_usb_00130201.bin
ar3k-firmware/lib/firmware/qca/nvm_usb_00130201_010a.bin
ar3k-firmware/lib/firmware/qca/nvm_usb_00130201_010b.bin
ar3k-firmware/lib/firmware/qca/nvm_usb_00130201_0303.bin
ar3k-firmware/lib/firmware/qca/nvm_usb_00130201_gf.bin
ar3k-firmware/lib/firmware/qca/nvm_usb_00130201_gf_010a.bin
ar3k-firmware/lib/firmware/qca/nvm_usb_00130201_gf_010b.bin
ar3k-firmware/lib/firmware/qca/nvm_usb_00130201_gf_0303.bin
ar3k-firmware/lib/firmware/qca/rampatch_usb_00130200.bin
ar3k-firmware/lib/firmware/qca/rampatch_usb_00130201.bin
iwlwifi-firmware-ax200/lib/firmware/iwlwifi-cc-a0-66.ucode
iwlwifi-firmware-ax210/lib/firmware/iwlwifi-ty-a0-gf-a0-66.ucode
iwlwifi-firmware-ax210/lib/firmware/iwlwifi-ty-a0-gf-a0.pnvm
iwlwifi-firmware-iwl9000/lib/firmware/iwlwifi-9000-pu-b0-jf-b0-46.ucode
iwlwifi-firmware-iwl9260/lib/firmware/iwlwifi-9260-th-b0-jf-b0-46.ucode
rtl8822ce-firmware/lib/firmware/rtw88/rtw8822c_fw.bin
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rafał Miłecki [Mon, 7 Mar 2022 10:12:36 +0000 (11:12 +0100)]
bcm4908: fix init on CFE devices
exit in preinit script was stopping whole process
Fixes: 93259e8ca261 ("bcm4908: support "rootfs_data" on U-Boot devices")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Felix Fietkau [Mon, 7 Mar 2022 09:37:15 +0000 (10:37 +0100)]
bpf-headers: ship a modified version of stdarg.h from musl to fix ebpf build on glibc
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Mon, 7 Mar 2022 07:43:52 +0000 (08:43 +0100)]
toolchain/binutils: remove old versions
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Sun, 6 Mar 2022 22:01:13 +0000 (23:01 +0100)]
qosify: update to the latest version
3276aed81c73 move run_cmd() to main.c
558eabc13c64 map: move dns host based lookup code to a separate function
6ff06d66c36c dns: add code for snooping dns packets
a78bd43c4a54 ubus: remove dnsmasq subscriber
9773ffa70f1f map: process dns patterns in the order in which they were defined
f13b67c9a786 dns: allow limiting dns entry matching to cname name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Bjørn Mork [Sat, 5 Mar 2022 09:36:07 +0000 (10:36 +0100)]
realtek: net: dsa: configure better brport flags when ports leave the bridge
Ensures that the DSA driver sets exactly the same default flags as the
bridge when a port joins or leaves. Without this we end up with a
confusing flag mismatch, where DSA and bridge ports use different sets
of flags.
This is critical as the "learning" mismatch will be harmful to the
network, causing all traffic to be flooded on all ports.
The original commit was buggy, trying to set the flags one-by-one in a
loop. This was not supported by the API and the end result was that
all but the last flag were cleared. This bug was implicitly fixed
upstream by commit
e18f4c18ab5b ("net: switchdev: pass flags and mask
to both {PRE_,}BRIDGE_FLAGS attributes").
This is a minimum temporary stop measure fix for the critical lack of
"learning" only. The major API change associated with a full v5.12+
backport is neither required nor wanted. A simpler fix, moving the
call to dsa_port_bridge_flags() out of the loop, has therefore been
merged into this modified backport.
Fixes: afa3ab54c03d ("realtek: Backport bridge configuration for DSA")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
[fix typos in commit message]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
INAGAKI Hiroshi [Sat, 17 Jul 2021 09:28:47 +0000 (18:28 +0900)]
ramips: use parser_trx for Buffalo WCR-1166DS
Buffalo WCR-1166DS uses trx-fomatted firmware and the custom magic
number (0x5C436F74, "\Cot") is required for OpenWrt installation from
OEM WebUI.
But the current mtdsplit_trx doesn't support the custom magic number and
fail to parse and split to kernel and rootfs when the factory image is
flashed. Then, the kernel fails to mount rootfs automatically and panics.
Before the commit
fddc78bc116bc043fb5cd92dbc45cfd054c21af8, mtdsplit_trx
was patched in ramips target and the device-specific magic number was
supported only for WCR-1166DS[1].
But the patch was not inherited to the later version of the kernel and
deleted by the above commit, then, the custom magic number support was
broken.
[1]: https://github.com/openwrt/openwrt/blob/
05d6e92594c507dcd1f4be6c1bcb2282fe1abe1f/target/linux/ramips/patches-4.4/0400-mtd-mtdsplit-add-support-for-custom-trx-magic-for-Buffalo-WCR-1166DS.patch#L27
log (factory image):
[ 1.165312] spi-mt7621
10000b00.spi: sys_freq:
193333333
[ 1.195782] spi-nor spi0.0: w25q128 (16384 Kbytes)
[ 1.205353] 7 fixed-partitions partitions found on MTD device spi0.0
[ 1.217938] Creating 7 MTD partitions on "spi0.0":
[ 1.227436] 0x000000000000-0x000000030000 : "u-boot"
[ 1.238427] 0x000000030000-0x000000040000 : "u-boot-env"
[ 1.250123] 0x000000040000-0x000000050000 : "factory"
[ 1.261306] 0x000000050000-0x000000810000 : "firmware"
[ 1.282051] 0x000000810000-0x000000fd0000 : "firmware2"
[ 1.293594] 0x000000fd0000-0x000000fe0000 : "glbcfg"
[ 1.304719] 0x000000fe0000-0x000000ff0000 : "board_data"
...
[ 1.452424] /dev/root: Can't open blockdev
[ 1.460619] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
[ 1.475434] Please append a correct "root=" boot option; here are the available partitions:
[ 1.491986] 1f00 192 mtdblock0
[ 1.491989] (driver?)
[ 1.504938] 1f01 64 mtdblock1
[ 1.504941] (driver?)
[ 1.517885] 1f02 64 mtdblock2
[ 1.517888] (driver?)
[ 1.530831] 1f03 7936 mtdblock3
[ 1.530834] (driver?)
[ 1.543777] 1f04 7936 mtdblock4
[ 1.543781] (driver?)
[ 1.556724] 1f05 64 mtdblock5
[ 1.556727] (driver?)
[ 1.569672] 1f06 64 mtdblock6
[ 1.569675] (driver?)
[ 1.582617] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[ 1.598976] Rebooting in 1 seconds..
This patch fixes this issue by using parser_trx with specifying custom
magic number in dts instead of mtdsplit_trx.
log (fixed factory image):
[ 1.202044] spi-mt7621
10000b00.spi: sys_freq:
193333333
[ 1.225369] spi-nor spi0.0: w25q128 (16384 Kbytes)
[ 1.235015] 7 fixed-partitions partitions found on MTD device spi0.0
[ 1.247603] Creating 7 MTD partitions on "spi0.0":
[ 1.257106] 0x000000000000-0x000000030000 : "u-boot"
[ 1.269447] 0x000000030000-0x000000040000 : "u-boot-env"
[ 1.281192] 0x000000040000-0x000000050000 : "factory"
[ 1.294208] 0x000000050000-0x000000810000 : "firmware"
[ 1.305774] 2 trx partitions found on MTD device firmware
[ 1.316540] Creating 2 MTD partitions on "firmware":
[ 1.326399] 0x00000000001c-0x000000214754 : "linux"
[ 1.336063] mtd: partition "linux" doesn't start on an erase/write block boundary -- force read-only
[ 1.357070] 0x000000214754-0x0000007c0000 : "rootfs"
[ 1.366994] mtd: partition "rootfs" doesn't start on an erase/write block boundary -- force read-only
[ 1.386368] mtd: device 5 (rootfs) set to be root filesystem
[ 1.398700] 1 squashfs-split partitions found on MTD device rootfs
[ 1.411027] 0x000000520000-0x0000007c0000 : "rootfs_data"
[ 1.422841] 0x000000810000-0x000000fd0000 : "firmware2"
[ 1.436282] 0x000000fd0000-0x000000fe0000 : "glbcfg"
[ 1.447408] 0x000000fe0000-0x000000ff0000 : "board_data"
...
[ 1.611216] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
INAGAKI Hiroshi [Sat, 12 Feb 2022 07:07:05 +0000 (16:07 +0900)]
ramips: switch parser of trx for mt76x8 subtarget
This patch enable parser_trx and disable mtdsplit_trx for mt76x8
subtarget.
The trx format is used only on Buffalo WCR-1166DS in mt76x8 subtarget
and the parser need to be switched to parser_trx to use the custom magic
number in the header for WCR-1166DS.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
INAGAKI Hiroshi [Sat, 12 Feb 2022 05:56:12 +0000 (14:56 +0900)]
kernel: backport patch to allow using parser_trx from ramips
This patch adds a patch to allow using parser_trx from ramips target,
mainly for Buffalo devices.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
INAGAKI Hiroshi [Sat, 12 Feb 2022 04:09:23 +0000 (13:09 +0900)]
kernel: move parser_trx patches of custom magic to generic
This patch moves the patches of parser_trx in mediatek target to
generic/backport-5.10 to use the changes from ramips target and
backport the additional patch of the parser.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
INAGAKI Hiroshi [Sat, 9 Jan 2021 04:24:37 +0000 (13:24 +0900)]
ramips: update MAC address configuration for Buffalo WCR-1166DS
This patch converts MAC address configuration of Buffalo WCR-1166DS in
02_network to use the generic function of OpenWrt. And also, add
label_mac.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
INAGAKI Hiroshi [Sat, 9 Jan 2021 06:16:44 +0000 (15:16 +0900)]
ramips: increase spi frequency for Buffalo WCR-1166DS
Use higher frequency than current and up the speed to access to the
flash on WCR-1166DS.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Joe Mullally [Sat, 19 Feb 2022 21:32:54 +0000 (21:32 +0000)]
ramips: Add support for TP-Link TL-WPA8631P v3
AV1300 Gigabit Passthrough Powerline ac Wi-Fi Extender
Specifications
--------------
* SoC: MediaTek MT7621AT
* CPU: 880 MHz MIPS 1004KEc dual-core CPU
* RAM: 64 MiB DDR2 (Zentel A3R12E40DBF-8E)
* Flash: 8 MiB SPI NOR (GigaDevice GD25Q64CSIG)
* Ethernet: SoC built-in Switch 5x 1GbE
* Port 0: PLC (connected through AR8035-A)
* Port 1-3: LAN
* WLAN: 2x2 2.4GHz 300 Mbps + 2x2 5GHz 867 Mbps (MT7603EN + MT7613BEN)
* PLC: HomePlug AV2 (Qualcomm QCA7500)
* PLC Flash: 2MiB SPI NOR (GigaDevice GD25Q16CSIG)
* Buttons: Reset, LED, Pair, Wi-Fi
* LEDs: Power (green), PLC (green/amber), LAN (green), 2.4G (green),
5G (green)
* UART: J1 (57600 baud)
* Pinout: (3V3) (GND) (RX) (TX)
* Visually identify GND from connection to PCB ground plane
Installation
------------
Installation is possible from the OEM web interface. Make sure to install
the latest OEM firmware first, so that the PLC firmware is at the latest
version. However, please first check the OpenWRT Wiki page for
confirmation that your OEM firmware version is supported.
Signed-off-by: Joe Mullally <jwmullally@gmail.com>
Hauke Mehrtens [Thu, 27 Jan 2022 12:30:38 +0000 (12:30 +0000)]
iproute2: Remove libxtables from some tc variants
This adds the new tc-bpf variant and removes libxtables dependency from
the tc-tiny variant. The tc-full variant stays like before and contains
everything.
This allows to use tc without libxtables.
The variants have the following sizes:
root@OpenWrt:/# ls -al /usr/libexec/tc-*
-rwxr-xr-x 1 root root 282453 Mar 1 21:55 /usr/libexec/tc-bpf
-rwxr-xr-x 1 root root 282533 Mar 1 21:55 /usr/libexec/tc-full
-rwxr-xr-x 1 root root 266037 Mar 1 21:55 /usr/libexec/tc-tiny
They are linking the following shared libraries:
root@OpenWrt:/# ldd /usr/libexec/tc-tiny
/lib/ld-musl-mips-sf.so.1 (0x77d6e000)
libgcc_s.so.1 => /lib/libgcc_s.so.1 (0x77d4a000)
libc.so => /lib/ld-musl-mips-sf.so.1 (0x77d6e000)
root@OpenWrt:/# ldd /usr/libexec/tc-bpf
/lib/ld-musl-mips-sf.so.1 (0x77da6000)
libbpf.so.0 => /usr/lib/libbpf.so.0 (0x77d60000)
libelf.so.1 => /usr/lib/libelf.so.1 (0x77d3e000)
libgcc_s.so.1 => /lib/libgcc_s.so.1 (0x77d1a000)
libc.so => /lib/ld-musl-mips-sf.so.1 (0x77da6000)
libz.so.1 => /usr/lib/libz.so.1 (0x77cf6000)
root@OpenWrt:/# ldd /usr/libexec/tc-full
/lib/ld-musl-mips-sf.so.1 (0x77de8000)
libbpf.so.0 => /usr/lib/libbpf.so.0 (0x77da2000)
libelf.so.1 => /usr/lib/libelf.so.1 (0x77d80000)
libxtables.so.12 => /usr/lib/libxtables.so.12 (0x77d66000)
libgcc_s.so.1 => /lib/libgcc_s.so.1 (0x77d42000)
libc.so => /lib/ld-musl-mips-sf.so.1 (0x77de8000)
libz.so.1 => /usr/lib/libz.so.1 (0x77d1e000)
This is based on a patch from Tiago Gaspar.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Langhua Ye [Fri, 4 Mar 2022 15:14:40 +0000 (23:14 +0800)]
uboot-envtools: mt7622: add support for Ruijie RG-EW3200GX PRO
Add U-Boot environment settings for Ruijie RG-EW3200GX PRO to allow
users to access the bootloader environment using fw_printenv/fw_setenv
while running OpenWrt.
Signed-off-by: Langhua Ye <y1248289414@outlook.com>
Langhua Ye [Fri, 4 Mar 2022 13:41:46 +0000 (21:41 +0800)]
mediatek: add support for Ruijie RG-EW3200GX PRO
X32 Pro is another product name for it in the Chinese market.
Specifications:
- SoC: MT7622B
- RAM: 256MB
- Flash: XMC XM25QH128C or Winbond WQ25Q128JVSQ 16MB SPI NOR
- Ethernet: 5x1GbE
- Switch: MT7531BE
- WiFi: 2.4G: MT7622 5G: MT7915AN+MT7975AN
- 3LEDs: System LED(blue) + Mesh LED(green) + Mesh LED(red)
- 2Keys: Mesh button + Reset button
- UART: Marked J19 on board. 3.3v, 115200n1
- Power: 12V 2.5A
MAC addresses as verified by OEM firmware:
use address source
WAN *:F4 ethaddr@product_info
LAN *:F5
5g *:F6
2g *:F7
Flash instruction:
1. Serve the initramfs.img using a TFTP server with address 10.10.10.3.
2. Interrupt the uboot startup process via UART.
3. Select "System Load Linux to SDRAM via TFTP" item.
4. (important) Back up firmware(mtd7) partitions with:
dd if=/dev/mtd7 of=/tmp/firmware.bin
and then download the firmware.bin image via SCP.
5. Flash the OpenWrt sysupgrade firmware.
Recovery stock firmware:
1. Transfer the firmware.bin image to the device.
2. Flash the image with:
mtd write firmware.bin firmware
Signed-off-by: Langhua Ye <y1248289414@outlook.com>
Langhua Ye [Thu, 3 Mar 2022 03:27:58 +0000 (11:27 +0800)]
kernel: add support for XMC XM25QH128C
The XMC XM25QH128C is a 16MB SPI NOR chip. The patch is verified on Ruijie RG-EW3200GX PRO.
Datasheet available at https://www.xmcwh.com/uploads/435/XM25QH128C.pdf
Signed-off-by: Langhua Ye <y1248289414@outlook.com>
Ansuel Smith [Wed, 2 Mar 2022 14:38:59 +0000 (15:38 +0100)]
libnetfilter-conntrack: backport patch fixing compilation with 5.15
Backport patch fixing compilation with 5.15 and musl provided by Robert Marko
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Rui Salvaterra [Wed, 2 Mar 2022 13:11:44 +0000 (13:11 +0000)]
kernel: bump 5.10 to 5.10.103
Patches automatically rebased.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
projects / openwrt / staging / chunkeey.git / log