Quinn Tran [Tue, 22 Oct 2019 19:36:43 +0000 (12:36 -0700)]
scsi: qla2xxx: Fix partial flash write of MBI
For new adapters with multiple flash regions to write to, current code
allows FW & Boot regions to be written, while other regions are blocked via
sysfs. The fix is to block all flash read/write through sysfs interface.
Fixes: e81d1bcbde06 ("scsi: qla2xxx: Further limit FLASH region write access from SysFS")
Cc: stable@vger.kernel.org # 5.2
Link: https://lore.kernel.org/r/20191022193643.7076-3-hmadhani@marvell.com
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Girish Basrur <gbasrur@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Himanshu Madhani [Tue, 22 Oct 2019 19:36:42 +0000 (12:36 -0700)]
scsi: qla2xxx: Initialized mailbox to prevent driver load failure
This patch fixes issue with Gen7 adapter in a blade environment where one
of the ports will not be detected by driver. Firmware expects mailbox 11 to
be set or cleared by driver for newer ISP.
Following message is seen in the log file:
[ 18.810892] qla2xxx [0000:d8:00.0]-1820:1: **** Failed=102 mb[0]=4005 mb[1]=37 mb[2]=20 mb[3]=8
[ 18.819596] cmd=2 ****
[mkp: typos]
Link: https://lore.kernel.org/r/20191022193643.7076-2-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Daniel Wagner [Tue, 22 Oct 2019 07:21:12 +0000 (09:21 +0200)]
scsi: lpfc: Honor module parameter lpfc_use_adisc
The initial lpfc_desc_set_adisc implementation in commit
dea3101e0a5c ("lpfc: add Emulex FC driver version 8.0.28") enabled ADISC if
cfg_use_adisc && RSCN_MODE && FCP_2_DEVICE
In commit
92d7f7b0cde3 ("[SCSI] lpfc: NPIV: add NPIV support on top of
SLI-3") this changed to
(cfg_use_adisc && RSC_MODE) || FCP_2_DEVICE
and later in commit
ffc954936b13 ("[SCSI] lpfc 8.3.13: FC Discovery Fixes
and enhancements.") to
(cfg_use_adisc && RSC_MODE) || (FCP_2_DEVICE && FCP_TARGET)
A customer reports that after a devloss, an ADISC failure is logged. It
turns out the ADISC flag is set even the user explicitly set lpfc_use_adisc
= 0.
[Sat Dec 22 22:55:58 2018] lpfc 0000:82:00.0: 2:(0):0203 Devloss timeout on WWPN 50:01:43:80:12:8e:40:20 NPort x05df00 Data: x82000000 x8 xa
[Sat Dec 22 23:08:20 2018] lpfc 0000:82:00.0: 2:(0):2755 ADISC failure DID:05DF00 Status:x9/x70000
[mkp: fixed Hannes' email]
Fixes: 92d7f7b0cde3 ("[SCSI] lpfc: NPIV: add NPIV support on top of SLI-3")
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: James Smart <james.smart@broadcom.com>
Link: https://lore.kernel.org/r/20191022072112.132268-1-dwagner@suse.de
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Avri Altman [Thu, 10 Oct 2019 08:31:07 +0000 (11:31 +0300)]
scsi: ufs-bsg: Wake the device before sending raw upiu commands
The scsi async probe process is calling blk_pm_runtime_init for each lun,
and then those request queues are monitored by the block layer pm
engine (blk-pm.c). This is however, not the case for scsi-passthrough
queues, created by bsg_setup_queue().
So the ufs-bsg driver might send various commands, disregarding the pm
status of the device. This is wrong, regardless if its request queue is
pm-aware or not.
Fixes: df032bf27a41 (scsi: ufs: Add a bsg endpoint that supports UPIUs)
Link: https://lore.kernel.org/r/1570696267-8487-1-git-send-email-avri.altman@wdc.com
Reported-by: Yuliy Izrailov <yuliy.izrailov@wdc.com>
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Daniel Wagner [Fri, 18 Oct 2019 16:21:11 +0000 (18:21 +0200)]
scsi: lpfc: Check queue pointer before use
The queue pointer might not be valid. The rest of the code checks the
pointer before accessing it. lpfc_sli4_process_missed_mbox_completions is
the only place where the check is missing.
Fixes: 657add4e5e15 ("scsi: lpfc: Fix poor use of hardware queues if fewer irq vectors")
Cc: James Smart <jsmart2021@gmail.com>
Link: https://lore.kernel.org/r/20191018162111.8798-1-dwagner@suse.de
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hannes Reinecke [Fri, 18 Oct 2019 14:04:58 +0000 (16:04 +0200)]
scsi: qla2xxx: fixup incorrect usage of host_byte
DRIVER_ERROR is a a driver byte setting, not a host byte. The qla2xxx
driver should rather return DID_ERROR here to be in line with the other
drivers.
Link: https://lore.kernel.org/r/20191018140458.108278-1-hare@suse.de
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hannes Reinecke [Thu, 17 Oct 2019 15:00:19 +0000 (17:00 +0200)]
scsi: lpfc: remove left-over BUILD_NVME defines
The BUILD_NVME define never got defined anywhere, causing NVMe commands to
be treated as SCSI commands when freeing the buffers. This was causing a
stuck discovery and a horrible crash in lpfc_set_rrq_active() later on.
Link: https://lore.kernel.org/r/20191017150019.75769-1-hare@suse.de
Fixes: c00f62e6c546 ("scsi: lpfc: Merge per-protocol WQ/CQ pairs into single per-cpu pair")
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Yufen Yu [Tue, 15 Oct 2019 13:05:56 +0000 (21:05 +0800)]
scsi: core: try to get module before removing device
We have a test case like block/001 in blktests, which will create a scsi
device by loading scsi_debug module and then try to delete the device by
sysfs interface. At the same time, it may remove the scsi_debug module.
And getting a invalid paging request BUG_ON as following:
[ 34.625854] BUG: unable to handle page fault for address:
ffffffffa0016bb8
[ 34.629189] Oops: 0000 [#1] SMP PTI
[ 34.629618] CPU: 1 PID: 450 Comm: bash Tainted: G W 5.4.0-rc3+ #473
[ 34.632524] RIP: 0010:scsi_proc_hostdir_rm+0x5/0xa0
[ 34.643555] CR2:
ffffffffa0016bb8 CR3:
000000012cd88000 CR4:
00000000000006e0
[ 34.644545] Call Trace:
[ 34.644907] scsi_host_dev_release+0x6b/0x1f0
[ 34.645511] device_release+0x74/0x110
[ 34.646046] kobject_put+0x116/0x390
[ 34.646559] put_device+0x17/0x30
[ 34.647041] scsi_target_dev_release+0x2b/0x40
[ 34.647652] device_release+0x74/0x110
[ 34.648186] kobject_put+0x116/0x390
[ 34.648691] put_device+0x17/0x30
[ 34.649157] scsi_device_dev_release_usercontext+0x2e8/0x360
[ 34.649953] execute_in_process_context+0x29/0x80
[ 34.650603] scsi_device_dev_release+0x20/0x30
[ 34.651221] device_release+0x74/0x110
[ 34.651732] kobject_put+0x116/0x390
[ 34.652230] sysfs_unbreak_active_protection+0x3f/0x50
[ 34.652935] sdev_store_delete.cold.4+0x71/0x8f
[ 34.653579] dev_attr_store+0x1b/0x40
[ 34.654103] sysfs_kf_write+0x3d/0x60
[ 34.654603] kernfs_fop_write+0x174/0x250
[ 34.655165] __vfs_write+0x1f/0x60
[ 34.655639] vfs_write+0xc7/0x280
[ 34.656117] ksys_write+0x6d/0x140
[ 34.656591] __x64_sys_write+0x1e/0x30
[ 34.657114] do_syscall_64+0xb1/0x400
[ 34.657627] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 34.658335] RIP: 0033:0x7f156f337130
During deleting scsi target, the scsi_debug module have been removed. Then,
sdebug_driver_template belonged to the module cannot be accessd, resulting
in scsi_proc_hostdir_rm() BUG_ON.
To fix the bug, we add scsi_device_get() in sdev_store_delete() to try to
increase refcount of module, avoiding the module been removed.
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191015130556.18061-1-yuyufen@huawei.com
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Don Brace [Mon, 14 Oct 2019 18:03:58 +0000 (13:03 -0500)]
scsi: hpsa: add missing hunks in reset-patch
Correct returning from reset before outstanding commands are completed
for the device.
Link: https://lore.kernel.org/r/157107623870.17997.11208813089704833029.stgit@brunhilda
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bodo Stroesser [Mon, 14 Oct 2019 18:29:04 +0000 (20:29 +0200)]
scsi: target: core: Do not overwrite CDB byte 1
passthrough_parse_cdb() - used by TCMU and PSCSI - attepts to reset the LUN
field of SCSI-2 CDBs (bits 5,6,7 of byte 1). The current code is wrong as
for newer commands not having the LUN field it overwrites relevant command
bits (e.g. for SECURITY PROTOCOL IN / OUT). We think this code was
unnecessary from the beginning or at least it is no longer useful. So we
remove it entirely.
Link: https://lore.kernel.org/r/12498eab-76fd-eaad-1316-c2827badb76a@ts.fujitsu.com
Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bart Van Assche [Wed, 9 Oct 2019 17:35:36 +0000 (10:35 -0700)]
scsi: ch: Make it possible to open a ch device multiple times again
Clearing ch->device in ch_release() is wrong because that pointer must
remain valid until ch_remove() is called. This patch fixes the following
crash the second time a ch device is opened:
BUG: kernel NULL pointer dereference, address:
0000000000000790
RIP: 0010:scsi_device_get+0x5/0x60
Call Trace:
ch_open+0x4c/0xa0 [ch]
chrdev_open+0xa2/0x1c0
do_dentry_open+0x13a/0x380
path_openat+0x591/0x1470
do_filp_open+0x91/0x100
do_sys_open+0x184/0x220
do_syscall_64+0x5f/0x1a0
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes: 085e56766f74 ("scsi: ch: add refcounting")
Cc: Hannes Reinecke <hare@suse.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191009173536.247889-1-bvanassche@acm.org
Reported-by: Rob Turk <robtu@rtist.nl>
Suggested-by: Rob Turk <robtu@rtist.nl>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Thomas Bogendoerfer [Wed, 9 Oct 2019 15:11:28 +0000 (17:11 +0200)]
scsi: fix kconfig dependency warning related to 53C700_LE_ON_BE
When building a kernel with SCSI_SNI_53C710 enabled, Kconfig warns:
WARNING: unmet direct dependencies detected for 53C700_LE_ON_BE
Depends on [n]: SCSI_LOWLEVEL [=y] && SCSI [=y] && SCSI_LASI700 [=n]
Selected by [y]:
- SCSI_SNI_53C710 [=y] && SCSI_LOWLEVEL [=y] && SNI_RM [=y] && SCSI [=y]
Add the missing depends SCSI_SNI_53C710 to 53C700_LE_ON_BE to fix it.
Link: https://lore.kernel.org/r/20191009151128.32411-1-tbogendoerfer@suse.de
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Thomas Bogendoerfer [Wed, 9 Oct 2019 15:11:18 +0000 (17:11 +0200)]
scsi: sni_53c710: fix compilation error
Drop out memory dev_printk() with wrong device pointer argument.
[mkp: typo]
Link: https://lore.kernel.org/r/20191009151118.32350-1-tbogendoerfer@suse.de
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hannes Reinecke [Mon, 7 Oct 2019 13:57:01 +0000 (15:57 +0200)]
scsi: scsi_dh_alua: handle RTPG sense code correctly during state transitions
Some arrays are not capable of returning RTPG data during state
transitioning, but rather return an 'LUN not accessible, asymmetric access
state transition' sense code. In these cases we can set the state to
'transitioning' directly and don't need to evaluate the RTPG data (which we
won't have anyway).
Link: https://lore.kernel.org/r/20191007135701.32389-1-hare@suse.de
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Allen Pais [Wed, 18 Sep 2019 16:36:58 +0000 (22:06 +0530)]
scsi: qla2xxx: fix a potential NULL pointer dereference
alloc_workqueue is not checked for errors and as a result a potential
NULL dereference could occur.
Link: https://lore.kernel.org/r/1568824618-4366-1-git-send-email-allen.pais@oracle.com
Signed-off-by: Allen Pais <allen.pais@oracle.com>
Reviewed-by: Martin Wilck <mwilck@suse.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Himanshu Madhani [Tue, 1 Oct 2019 15:33:38 +0000 (08:33 -0700)]
scsi: MAINTAINERS: Update qla2xxx driver
Update maintainer entry for qla2xxx driver now that email addresses have
been changed to Marvell.
Link: https://lore.kernel.org/r/20191001153338.28765-1-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Steffen Maier [Tue, 1 Oct 2019 10:49:49 +0000 (12:49 +0200)]
scsi: zfcp: fix reaction on bit error threshold notification
On excessive bit errors for the FCP channel ingress fibre path, the channel
notifies us. Previously, we only emitted a kernel message and a trace
record. Since performance can become suboptimal with I/O timeouts due to
bit errors, we now stop using an FCP device by default on channel
notification so multipath on top can timely failover to other paths. A new
module parameter zfcp.ber_stop can be used to get zfcp old behavior.
User explanation of new kernel message:
* Description:
* The FCP channel reported that its bit error threshold has been exceeded.
* These errors might result from a problem with the physical components
* of the local fibre link into the FCP channel.
* The problem might be damage or malfunction of the cable or
* cable connection between the FCP channel and
* the adjacent fabric switch port or the point-to-point peer.
* Find details about the errors in the HBA trace for the FCP device.
* The zfcp device driver closed down the FCP device
* to limit the performance impact from possible I/O command timeouts.
* User action:
* Check for problems on the local fibre link, ensure that fibre optics are
* clean and functional, and all cables are properly plugged.
* After the repair action, you can manually recover the FCP device by
* writing "0" into its "failed" sysfs attribute.
* If recovery through sysfs is not possible, set the CHPID of the device
* offline and back online on the service element.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: <stable@vger.kernel.org> #2.6.30+
Link: https://lore.kernel.org/r/20191001104949.42810-1-maier@linux.ibm.com
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Damien Le Moal [Tue, 1 Oct 2019 07:48:39 +0000 (16:48 +0900)]
scsi: core: save/restore command resid for error handling
When a non-passthrough command is terminated with CHECK CONDITION, request
sense is executed by hijacking the command descriptor. Since
scsi_eh_prep_cmnd() and scsi_eh_restore_cmnd() do not save/restore the
original command resid, the value returned on failure of the original
command is lost and replaced with the value set by the execution of the
request sense command. This value may in many instances be unaligned to the
device sector size, causing sd_done() to print a warning message about the
incorrect unaligned resid before the command is retried.
Fix this problem by saving the original command residual in struct
scsi_eh_save using scsi_eh_prep_cmnd() and restoring it in
scsi_eh_restore_cmnd(). In addition, to make sure that the request sense
command is executed with a correctly initialized command structure, also
reset the residual to 0 in scsi_eh_prep_cmnd() after saving the original
command value in struct scsi_eh_save.
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191001074839.1994-1-damien.lemoal@wdc.com
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Daniel Wagner [Fri, 27 Sep 2019 07:30:31 +0000 (09:30 +0200)]
scsi: qla2xxx: Remove WARN_ON_ONCE in qla2x00_status_cont_entry()
Commit
88263208dd23 ("scsi: qla2xxx: Complain if sp->done() is not called
from the completion path") introduced the WARN_ON_ONCE in
qla2x00_status_cont_entry(). The assumption was that there is only one
status continuations element. According to the firmware documentation it is
possible that multiple status continuations are emitted by the firmware.
Fixes: 88263208dd23 ("scsi: qla2xxx: Complain if sp->done() is not called from the completion path")
Link: https://lore.kernel.org/r/20190927073031.62296-1-dwagner@suse.de
Cc: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Oliver Neukum [Tue, 3 Sep 2019 10:18:39 +0000 (12:18 +0200)]
scsi: sd: Ignore a failure to sync cache due to lack of authorization
I've got a report about a UAS drive enclosure reporting back Sense: Logical
unit access not authorized if the drive it holds is password protected.
While the drive is obviously unusable in that state as a mass storage
device, it still exists as a sd device and when the system is asked to
perform a suspend of the drive, it will be sent a SYNCHRONIZE CACHE. If
that fails due to password protection, the error must be ignored.
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20190903101840.16483-1-oneukum@suse.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Thu, 12 Sep 2019 18:09:11 +0000 (11:09 -0700)]
scsi: qla2xxx: Fix Nport ID display value
For N2N, the NPort ID is assigned by driver in the PLOGI ELS. According to
FW Spec the byte order for SID is not the same as DID.
Link: https://lore.kernel.org/r/20190912180918.6436-8-hmadhani@marvell.com
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Tested-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Thu, 12 Sep 2019 18:09:10 +0000 (11:09 -0700)]
scsi: qla2xxx: Fix N2N link up fail
During link up/bounce, qla driver would do command flush as part of
cleanup. In this case, the flush can intefere with FW state. This patch
allows FW to be in control of link up.
Link: https://lore.kernel.org/r/20190912180918.6436-7-hmadhani@marvell.com
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Thu, 12 Sep 2019 18:09:09 +0000 (11:09 -0700)]
scsi: qla2xxx: Fix N2N link reset
Fix stalled link recovery for N2N with FC-NVMe connection.
Link: https://lore.kernel.org/r/20190912180918.6436-6-hmadhani@marvell.com
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Thu, 12 Sep 2019 18:09:08 +0000 (11:09 -0700)]
scsi: qla2xxx: Optimize NPIV tear down process
In the case of NPIV port is being torn down, this patch will set a flag to
indicate VPORT_DELETE. This would prevent relogin to be triggered.
Link: https://lore.kernel.org/r/20190912180918.6436-5-hmadhani@marvell.com
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Thu, 12 Sep 2019 18:09:07 +0000 (11:09 -0700)]
scsi: qla2xxx: Fix stale mem access on driver unload
On driver unload, 'remove_one' thread was allowed to advance, while session
cleanup still lag behind. This patch ensures session deletion will finish
before remove_one can advance.
Link: https://lore.kernel.org/r/20190912180918.6436-4-hmadhani@marvell.com
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Thu, 12 Sep 2019 18:09:06 +0000 (11:09 -0700)]
scsi: qla2xxx: Fix unbound sleep in fcport delete path.
There are instances, though rare, where a LOGO request cannot be sent out
and the thread in free session done can wait indefinitely. Fix this by
putting an upper bound to sleep.
Link: https://lore.kernel.org/r/20190912180918.6436-3-hmadhani@marvell.com
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Himanshu Madhani [Thu, 12 Sep 2019 18:09:05 +0000 (11:09 -0700)]
scsi: qla2xxx: Silence fwdump template message
Print if fwdt template is present or not, only when
ql2xextended_error_logging is enabled.
Link: https://lore.kernel.org/r/20190912180918.6436-2-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
YueHaibing [Mon, 23 Sep 2019 05:40:35 +0000 (13:40 +0800)]
scsi: hisi_sas: Make three functions static
Fix sparse warnings:
drivers/scsi/hisi_sas/hisi_sas_main.c:3686:6:
warning: symbol 'hisi_sas_debugfs_release' was not declared. Should it be static?
drivers/scsi/hisi_sas/hisi_sas_main.c:3708:5:
warning: symbol 'hisi_sas_debugfs_alloc' was not declared. Should it be static?
drivers/scsi/hisi_sas/hisi_sas_main.c:3799:6:
warning: symbol 'hisi_sas_debugfs_bist_init' was not declared. Should it be static?
Link: https://lore.kernel.org/r/20190923054035.19036-1-yuehaibing@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Xiang Chen [Sat, 7 Sep 2019 01:07:30 +0000 (09:07 +0800)]
scsi: megaraid: disable device when probe failed after enabled device
For pci device, need to disable device when probe failed after enabled
device.
Link: https://lore.kernel.org/r/1567818450-173315-1-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Long Li [Fri, 6 Sep 2019 17:24:20 +0000 (10:24 -0700)]
scsi: storvsc: setup 1:1 mapping between hardware queue and CPU queue
storvsc doesn't use a dedicated hardware queue for a given CPU queue. When
issuing I/O, it selects returning CPU (hardware queue) dynamically based on
vmbus channel usage across all channels.
This patch advertises num_present_cpus() as number of hardware queues. This
will have upper layer setup 1:1 mapping between hardware queue and CPU
queue and avoid unnecessary locking when issuing I/O.
Link: https://lore.kernel.org/r/1567790660-48142-1-git-send-email-longli@linuxonhyperv.com
Signed-off-by: Long Li <longli@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Austin Kim [Thu, 19 Sep 2019 07:55:48 +0000 (16:55 +0900)]
scsi: qedf: Remove always false 'tmp_prio < 0' statement
Since tmp_prio is declared as u8, the following statement is always false.
tmp_prio < 0
So remove 'always false' statement.
Link: https://lore.kernel.org/r/20190919075548.GA112801@LGEARND20B15
Signed-off-by: Austin Kim <austindh.kim@gmail.com>
Acked-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stanley Chu [Wed, 18 Sep 2019 04:20:38 +0000 (12:20 +0800)]
scsi: ufs: skip shutdown if hba is not powered
In some cases, hba may go through shutdown flow without successful
initialization and then make system hang.
For example, if ufshcd_change_power_mode() gets error and leads to
ufshcd_hba_exit() to release resources of the host, future shutdown flow
may hang the system since the host register will be accessed in unpowered
state.
To solve this issue, simply add checking to skip shutdown for above kind of
situation.
Link: https://lore.kernel.org/r/1568780438-28753-1-git-send-email-stanley.chu@mediatek.com
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Acked-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Laurence Oberman [Wed, 11 Sep 2019 13:56:42 +0000 (09:56 -0400)]
scsi: bnx2fc: Handle scope bits when array returns BUSY or TSF
The qla2xxx driver had this issue as well when the newer array firmware
returned the retry_delay_timer in the fcp_rsp. The bnx2fc is not handling
the masking of the scope bits either so the retry_delay_timestamp value
lands up being a large value added to the timer timestamp delaying I/O for
up to 27 Minutes. This patch adds similar code to handle this to the
bnx2fc driver to avoid the huge delay.
Link: https://lore.kernel.org/r/1568210202-12794-1-git-send-email-loberman@redhat.com
Signed-off-by: Laurence Oberman <loberman@redhat.com>
Reported-by: David Jeffery <djeffery@redhat.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Xiang Chen [Fri, 6 Sep 2019 12:55:37 +0000 (20:55 +0800)]
scsi: hisi_sas: Fix the conflict between device gone and host reset
When device gone, it will check whether it is during reset, if not, it will
send internal task abort. Before internal task abort returned, reset
begins, and it will check whether SAS_PHY_UNUSED is set, if not, it will
call hisi_sas_init_device(), but at that time domain_device may already be
freed or part of it is freed, so it may referenece null pointer in
hisi_sas_init_device(). It may occur as follows:
thread0 thread1
hisi_sas_dev_gone()
check whether in RESET(no)
internal task abort
reset prep
soft_reset
... (part of reset_done)
internal task abort failed
release resource anyway
clear_itct
device->lldd_dev=NULL
hisi_sas_reset_init_all_device
check sas_dev->dev_type is SAS_PHY_UNUSED and
!device
set dev_type SAS_PHY_UNUSED
sas_free_device
hisi_sas_init_device
...
Semaphore hisi_hba.sema is used to sync the processes of device gone and
host reset.
To solve the issue, expand the scope that semaphore protects and let them
never occur together.
And also some places will check whether domain_device is NULL to judge
whether the device is gone. So when device gone, need to clear
sas_dev->sas_device.
Link: https://lore.kernel.org/r/1567774537-20003-14-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Xiang Chen [Fri, 6 Sep 2019 12:55:36 +0000 (20:55 +0800)]
scsi: hisi_sas: Add BIST support for phy loopback
Add BIST (built in self test) support for phy loopback.
Through the new debugfs interface, the user can configure loopback
mode/linkrate/phy id/code mode before enabling it. And also user can
enable/disable BIST function.
Link: https://lore.kernel.org/r/1567774537-20003-13-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Luo Jiaxing [Fri, 6 Sep 2019 12:55:35 +0000 (20:55 +0800)]
scsi: hisi_sas: Add hisi_sas_debugfs_alloc() to centralise allocation
We extract the code of memory allocate and construct an new function for
it. We think it's convenient for subsequent optimization.
Link: https://lore.kernel.org/r/1567774537-20003-12-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Luo Jiaxing [Fri, 6 Sep 2019 12:55:34 +0000 (20:55 +0800)]
scsi: hisi_sas: Remove some unused function arguments
Some function arguments are unused, so remove them.
Also move the timeout print in for wait_cmds_complete_timeout_vX_hw()
callsites into that same function.
Link: https://lore.kernel.org/r/1567774537-20003-11-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Xiang Chen [Fri, 6 Sep 2019 12:55:33 +0000 (20:55 +0800)]
scsi: hisi_sas: Remove redundant work declaration
Remove redundant work declaration in HISI_SAS_DECLARE_RST_WORK_ON_STACK
Link: https://lore.kernel.org/r/1567774537-20003-10-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Luo Jiaxing [Fri, 6 Sep 2019 12:55:32 +0000 (20:55 +0800)]
scsi: hisi_sas: Remove hisi_sas_hw.slot_complete
We never call hisi_sas_hw.slot_complete, so remove it.
Link: https://lore.kernel.org/r/1567774537-20003-9-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Xiang Chen [Fri, 6 Sep 2019 12:55:31 +0000 (20:55 +0800)]
scsi: hisi_sas: Assign NCQ tag for all NCQ commands
Currently the NCQ tag is only assigned for FPDMA READ and FPDMA WRITE
commands, and for other NCQ commands (such as FPDMA SEND), their NCQ tags
are set in the delivery command to 0.
So for all the NCQ commands, we also need to assign normal NCQ tag for
them, so drop the command type check in hisi_sas_get_ncq_tag() [drop
hisi_sas_get_ncq_tag() altogether actually], and always use the ATA command
NCQ tag when appropriate.
Link: https://lore.kernel.org/r/1567774537-20003-8-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Xiang Chen [Fri, 6 Sep 2019 12:55:30 +0000 (20:55 +0800)]
scsi: hisi_sas: Update all the registers after suspend and resume
After suspend and resume, the HW registers will be set back to their
initial value. We use init_reg_v3_hw() to set some registers, but some
registers are set via firmware in ACPI "_RST" method, so add reset handler
before init_reg_v3_hw().
Link: https://lore.kernel.org/r/1567774537-20003-7-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Xiang Chen [Fri, 6 Sep 2019 12:55:29 +0000 (20:55 +0800)]
scsi: hisi_sas: Retry 3 times TMF IO for SAS disks when init device
When init device for SAS disks, it will send TMF IO to clear disks. At that
time TMF IO is broken by some operations such as injecting controller reset
from HW RAs event, the TMF IO will be timeout, and at last device will be
gone. Print is as followed:
hisi_sas_v3_hw 0000:74:02.0: dev[240:1] found
...
hisi_sas_v3_hw 0000:74:02.0: controller resetting...
hisi_sas_v3_hw 0000:74:02.0: phyup: phy7 link_rate=10(sata)
hisi_sas_v3_hw 0000:74:02.0: phyup: phy0 link_rate=9(sata)
hisi_sas_v3_hw 0000:74:02.0: phyup: phy1 link_rate=9(sata)
hisi_sas_v3_hw 0000:74:02.0: phyup: phy2 link_rate=9(sata)
hisi_sas_v3_hw 0000:74:02.0: phyup: phy3 link_rate=9(sata)
hisi_sas_v3_hw 0000:74:02.0: phyup: phy6 link_rate=10(sata)
hisi_sas_v3_hw 0000:74:02.0: phyup: phy5 link_rate=11
hisi_sas_v3_hw 0000:74:02.0: phyup: phy4 link_rate=11
hisi_sas_v3_hw 0000:74:02.0: controller reset complete
hisi_sas_v3_hw 0000:74:02.0: abort tmf: TMF task timeout and not done
hisi_sas_v3_hw 0000:74:02.0: dev[240:1] is gone
sas: driver on host 0000:74:02.0 cannot handle device
5000c500a75a860d,
error:5
To improve the reliability, retry TMF IO max of 3 times for SAS disks which
is the same as softreset does.
Link: https://lore.kernel.org/r/1567774537-20003-6-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Luo Jiaxing [Fri, 6 Sep 2019 12:55:28 +0000 (20:55 +0800)]
scsi: hisi_sas: Remove sleep after issue phy reset if sas_smp_phy_control() fails
At expander environment, we delay after issue phy reset to wait for
hardware to handle phy reset. But if sas_smp_phy_control() fails, the
delay is unnecessary so remove it.
Link: https://lore.kernel.org/r/1567774537-20003-5-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Luo Jiaxing [Fri, 6 Sep 2019 12:55:27 +0000 (20:55 +0800)]
scsi: hisi_sas: Directly return when running I_T_nexus reset if phy disabled
At hisi_sas_debug_I_T_nexus_reset(), we call sas_phy_reset() to reset a
phy. But if the phy is disabled, sas_phy_reset() will directly return
-ENODEV without issue a phy reset request.
If so, We can directly return -ENODEV to libsas before issue a phy
reset.
Link: https://lore.kernel.org/r/1567774537-20003-4-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Luo Jiaxing [Fri, 6 Sep 2019 12:55:26 +0000 (20:55 +0800)]
scsi: hisi_sas: Use true/false as input parameter of sas_phy_reset()
When calling sas_phy_reset(), we need to specify whether the reset type
is hard reset or link reset - use true/false for clarity.
Link: https://lore.kernel.org/r/1567774537-20003-3-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Luo Jiaxing [Fri, 6 Sep 2019 12:55:25 +0000 (20:55 +0800)]
scsi: hisi_sas: add debugfs auto-trigger for internal abort time out
This trigger is add at _hisi_sas_internal_task_abort()
Link: https://lore.kernel.org/r/1567774537-20003-2-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Matt Lupfer [Thu, 5 Sep 2019 18:19:28 +0000 (18:19 +0000)]
scsi: virtio_scsi: unplug LUNs when events missed
The event handler calls scsi_scan_host() when events are missed, which will
hotplug new LUNs. However, this function won't remove any unplugged LUNs.
The result is that hotunplug doesn't work properly when the number of
unplugged LUNs exceeds the event queue size (currently 8).
Scan existing LUNs when events are missed to check if they are still
present. If not, remove them.
Link: https://lore.kernel.org/r/20190905181903.29756-1-mlupfer@ddn.com
Signed-off-by: Matt Lupfer <mlupfer@ddn.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Martin Wilck [Wed, 4 Sep 2019 15:52:29 +0000 (15:52 +0000)]
scsi: scsi_dh_rdac: zero cdb in send_mode_select()
cdb in send_mode_select() is not zeroed and is only partially filled in
rdac_failover_get(), which leads to some random data getting to the
device. Users have reported storage responding to such commands with
INVALID FIELD IN CDB. Code before commit
327825574132 was not affected, as
it called blk_rq_set_block_pc().
Fix this by zeroing out the cdb first.
Identified & fix proposed by HPE.
Fixes: 327825574132 ("scsi_dh_rdac: switch to scsi_execute_req_flags()")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20190904155205.1666-1-martin.wilck@suse.com
Signed-off-by: Martin Wilck <mwilck@suse.com>
Acked-by: Ales Novak <alnovak@suse.cz>
Reviewed-by: Shane Seymour <shane.seymour@hpe.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
zhengbin [Tue, 20 Aug 2019 05:43:09 +0000 (13:43 +0800)]
scsi: fcoe: fix null-ptr-deref Read in fc_release_transport
In fcoe_if_init, if fc_attach_transport(&fcoe_vport_fc_functions)
fails, need to free the previously memory and return fail, otherwise
will trigger null-ptr-deref Read in fc_release_transport.
fcoe_exit
fcoe_if_exit
fc_release_transport(fcoe_vport_scsi_transport)
Link: https://lore.kernel.org/r/1566279789-58207-1-git-send-email-zhengbin13@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
YueHaibing [Wed, 4 Sep 2019 13:04:57 +0000 (21:04 +0800)]
scsi: ufs-hisi: use devm_platform_ioremap_resource() to simplify code
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Link: https://lore.kernel.org/r/20190904130457.24744-1-yuehaibing@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
YueHaibing [Wed, 4 Sep 2019 13:03:48 +0000 (21:03 +0800)]
scsi: ufshcd: use devm_platform_ioremap_resource() to simplify code
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Link: https://lore.kernel.org/r/20190904130348.24772-1-yuehaibing@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
YueHaibing [Wed, 4 Sep 2019 13:02:56 +0000 (21:02 +0800)]
scsi: hisi_sas: use devm_platform_ioremap_resource() to simplify code
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Link: https://lore.kernel.org/r/20190904130256.24704-1-yuehaibing@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
YueHaibing [Sat, 31 Aug 2019 12:44:24 +0000 (12:44 +0000)]
scsi: ufs: Use kmemdup in ufshcd_read_string_desc()
Use kmemdup rather than duplicating its implementation
Link: https://lore.kernel.org/r/20190831124424.18642-1-yuehaibing@huawei.com
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bjorn Andersson [Wed, 28 Aug 2019 19:17:56 +0000 (12:17 -0700)]
scsi: arm64: dts: qcom: sdm845: Specify UFS device-reset GPIO
Specify the UFS device-reset gpio for db845c and mtp, so that the
controller will issue a reset of the UFS device.
Link: https://lore.kernel.org/r/20190828191756.24312-4-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bjorn Andersson [Wed, 28 Aug 2019 19:17:55 +0000 (12:17 -0700)]
scsi: ufs-qcom: Implement device_reset vops
The UFS_RESET pin on Qualcomm SoCs are controlled by TLMM and exposed
through the GPIO framework. Acquire the device-reset GPIO and use this to
implement the device_reset vops, to allow resetting the attached memory.
Based on downstream support implemented by Subhash Jadavani
<subhashj@codeaurora.org>.
Link: https://lore.kernel.org/r/20190828191756.24312-3-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bjorn Andersson [Wed, 28 Aug 2019 19:17:54 +0000 (12:17 -0700)]
scsi: ufs: Introduce vops for resetting device
Some UFS memory devices needs their reset line toggled in order to get them
into a good state for initialization. Provide a new vops to allow the
platform driver to implement this operation.
Link: https://lore.kernel.org/r/20190828191756.24312-2-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Acked-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Tue, 3 Sep 2019 21:54:41 +0000 (14:54 -0700)]
scsi: lpfc: Fix reset recovery paths that are not recovering
A recent patch unconditionally marks the hba as in error as part of
resetting the adapter. The driver flow that called the adapter reset was a
recovery path, which expects the adapter to not be in an error state in
order to finish the recovery. Given the new error state being set, the
recovery fails and the adapter is left in limbo.
Revise the adapter reset routine so that it will only mark the adapter in
error if it was unable to reset the adapter.
Fixes: 8c24a4f643ed ("scsi: lpfc: Fix crash due to port reset racing vs adapter error handling")
Link: https://lore.kernel.org/r/20190903215441.10490-1-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Sakari Ailus [Wed, 4 Sep 2019 16:04:23 +0000 (19:04 +0300)]
scsi: lpfc: Convert existing %pf users to %ps
Convert the remaining %pf users to %ps to prepare for the removal of the
old %pf conversion specifier support.
Fixes: 323506644972 ("scsi: lpfc: Migrate to %px and %pf in kernel print calls")
Link: https://lore.kernel.org/r/20190904160423.3865-1-sakari.ailus@linux.intel.com
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Himanshu Madhani [Fri, 30 Aug 2019 22:24:02 +0000 (15:24 -0700)]
scsi: qla2xxx: Update driver version to 10.01.00.19-k
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Link: https://lore.kernel.org/r/20190830222402.23688-7-hmadhani@marvell.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Fri, 30 Aug 2019 22:24:01 +0000 (15:24 -0700)]
scsi: qla2xxx: Fix stale session
On fast cable pull, where driver is unable to detect device has disappeared
and came back based on switch info, qla2xxx would not re-login while remote
port has already invalidated the session. This causes IO timeout. This
patch would relogin to remote device for RSCN affected port.
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Link: https://lore.kernel.org/r/20190830222402.23688-6-hmadhani@marvell.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Fri, 30 Aug 2019 22:24:00 +0000 (15:24 -0700)]
scsi: qla2xxx: Fix stuck login session
Login session was stucked on cable pull. When FW is in the middle PRLI
PENDING + driver is in Initiator mode, driver fails to check back with FW to
see if the PRLI has completed. This patch would re-check with FW again to
make sure PRLI would complete before pushing forward with relogin.
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Link: https://lore.kernel.org/r/20190830222402.23688-5-hmadhani@marvell.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Himanshu Madhani [Fri, 30 Aug 2019 22:23:59 +0000 (15:23 -0700)]
scsi: qla2xxx: Fix driver reload for ISP82xx
HINT_MBX_INT_PENDING is not guaranteed to be cleared by firmware. Remove
check that prevent driver load with ISP82XX.
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Link: https://lore.kernel.org/r/20190830222402.23688-4-hmadhani@marvell.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Fri, 30 Aug 2019 22:23:58 +0000 (15:23 -0700)]
scsi: qla2xxx: Fix flash read for Qlogic ISPs
Use adapter specific callback to read flash instead of ISP adapter
specific.
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Link: https://lore.kernel.org/r/20190830222402.23688-3-hmadhani@marvell.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Himanshu Madhani [Fri, 30 Aug 2019 22:23:57 +0000 (15:23 -0700)]
scsi: qla2xxx: Fix message indicating vectors used by driver
This patch updates log message which indicates number of vectors used by
the driver instead of displaying failure to get maximum requested
vectors. Driver will always request maximum vectors during
initialization. In the event driver is not able to get maximum requested
vectors, it will adjust the allocated vectors. This is normal and does not
imply failure in driver.
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Link: https://lore.kernel.org/r/20190830222402.23688-2-hmadhani@marvell.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Damien Le Moal [Wed, 28 Aug 2019 05:35:11 +0000 (14:35 +0900)]
scsi: sd: Improve unaligned completion resid message
For commands completing with a resid not aligned on the device logical
sector size, also print the command CDB in addition to the current message
to help debug hardware generating such incorrect command completion
information.
Link: https://lore.kernel.org/r/20190828053511.14818-1-damien.lemoal@wdc.com
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Govindarajulu Varadarajan [Tue, 27 Aug 2019 21:13:40 +0000 (14:13 -0700)]
scsi: fnic: fix msix interrupt allocation
pci_alloc_irq_vectors() returns number of vectors allocated. Fix the check
for error condition.
Fixes: cca678dfbad49 ("scsi: fnic: switch to pci_alloc_irq_vectors")
Link: https://lore.kernel.org/r/20190827211340.1095-1-gvaradar@cisco.com
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Acked-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
John Pittman [Fri, 23 Aug 2019 14:08:52 +0000 (10:08 -0400)]
scsi: fnic: print port speed only at driver init or speed change
Port speed printing was added by commit
d948e6383ec3 ("scsi: fnic: Add port
speed stat to fnic debug stats"). As currently configured, this will cause
the port speed to be printed to syslog every 2 seconds. To prevent log
spamming, only print the vnic port speed at driver initialization and if
the speed changes. Also clean up a small typo in fnic_trace.c.
Fixes: d948e6383ec3 ("scsi: fnic: Add port speed stat to fnic debug stats")
Signed-off-by: John Pittman <jpittman@redhat.com>
Reviewed-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
zhengbin [Fri, 23 Aug 2019 13:22:53 +0000 (21:22 +0800)]
scsi: bnx2fc: remove set but not used variables 'task','port','orig_task'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/bnx2fc/bnx2fc_hwi.c: In function bnx2fc_process_unsol_compl:
drivers/scsi/bnx2fc/bnx2fc_hwi.c:636:30: warning: variable task set but not used [-Wunused-but-set-variable]
drivers/scsi/bnx2fc/bnx2fc_hwi.c: In function bnx2fc_process_ofld_cmpl:
drivers/scsi/bnx2fc/bnx2fc_hwi.c:1125:21: warning: variable port set but not used [-Wunused-but-set-variable]
drivers/scsi/bnx2fc/bnx2fc_hwi.c: In function bnx2fc_init_seq_cleanup_task:
drivers/scsi/bnx2fc/bnx2fc_hwi.c:1468:30: warning: variable orig_task set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Acked-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
zhengbin [Fri, 23 Aug 2019 13:22:52 +0000 (21:22 +0800)]
scsi: bnx2fc: remove set but not used variables 'lport','host'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/bnx2fc/bnx2fc_io.c: In function bnx2fc_initiate_seq_cleanup:
drivers/scsi/bnx2fc/bnx2fc_io.c:932:19: warning: variable lport set but not used [-Wunused-but-set-variable]
drivers/scsi/bnx2fc/bnx2fc_io.c: In function bnx2fc_initiate_cleanup:
drivers/scsi/bnx2fc/bnx2fc_io.c:1001:19: warning: variable lport set but not used [-Wunused-but-set-variable]
drivers/scsi/bnx2fc/bnx2fc_io.c: In function bnx2fc_process_scsi_cmd_compl:
drivers/scsi/bnx2fc/bnx2fc_io.c:1882:20: warning: variable host set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Acked-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
zhengbin [Fri, 23 Aug 2019 13:22:51 +0000 (21:22 +0800)]
scsi: bnx2fc: remove set but not used variable 'fh'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/bnx2fc/bnx2fc_fcoe.c: In function bnx2fc_rcv:
drivers/scsi/bnx2fc/bnx2fc_fcoe.c:431:26: warning: variable fh set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Acked-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Saurav Kashyap [Fri, 23 Aug 2019 09:52:44 +0000 (02:52 -0700)]
scsi: qedf: Update the version to 8.42.3.0
Update the driver version to 8.42.3.0.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Saurav Kashyap [Fri, 23 Aug 2019 09:52:43 +0000 (02:52 -0700)]
scsi: qedf: Fix race betwen fipvlan request and response path
There is a race b/w fipvlan request and response path:
=====
qedf_fcoe_process_vlan_resp:113]:2: VLAN response, vid=0xffd.
qedf_initiate_fipvlan_req:165]:2: vlan = 0x6ffd already set.
qedf_set_vlan_id:139]:2: Setting vlan_id=0ffd prio=3.
======
The request thread sees that vlan is already set and fails to call
ctrl_link_up.
Fix:
- While setting vlan_id use local variable and before setting vlan_id.
- Call fcoe_ctlr_link_up in next iteration of fipvlan request.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hannes Reinecke [Fri, 23 Aug 2019 09:52:42 +0000 (02:52 -0700)]
scsi: qedf: Use discovery list to traverse rports
The list of rports might become stale so we should rather traverse the
discovery list when trying relogin.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Saurav Kashyap [Fri, 23 Aug 2019 09:52:41 +0000 (02:52 -0700)]
scsi: qedf: Decrease the LL2 MTU size to 2500
Decrease the LL2 MTU size to 2500.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Saurav Kashyap [Fri, 23 Aug 2019 09:52:40 +0000 (02:52 -0700)]
scsi: qedf: Check for module unloading bit before processing link update AEN
Prevent race where we're removing the module and we get link update
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Saurav Kashyap [Fri, 23 Aug 2019 09:52:39 +0000 (02:52 -0700)]
scsi: qedf: Initiator fails to re-login to switch after link down
Problem Statement:
- Driver has fc_id of 0xcc0200
- Driver gets link down (due to test) and calls fcoe_ctlr_link_down().
- At this point, the fc_id of the initiator port is zeroed out.
- Driver gets a link up 14 seconds later.
- Driver performs FIP VLAN request, gets a response from the switch.
- No change in VLAN is detected.
- Driver then notifies libfcoe via fcoe_ctlr_link_up().
- Libfcoe then issues a multicast discovery solicitation as expected.
- Cisco FCF responds to that correctly.
- Libfcoe at this point starts a 3 sec count-down to allow any other FCFs
to be discovered. However, at this point, it has been 20 seconds since
the last FKA from the driver (which would have been sent prior to
backlink toggle), which causes the CVL to be issued from Cisco CVL from
the switch is dropped by the driver as the vx_port identification
descriptor is present and has value of 0xcc0200, which does not match
the driver's value of 0. Libfcoe completes the 3 sec count down and
proceeds to issue FLOGI as per protocol. Switch rejects FLogi request.
All subsequent FLOGI requests from libfc are rejected by the switch
(possibly because it is now expecting a new solicitation). This
situation will continue until the next link toggle.
Solution:
The Vx_port descriptor in the CVL has three fields:
MAC address
Fabric ID
Port Name
Today, the code checks for both #1 and #2 above. In the case where we went
through a link down, both these will be zero until FLOGI succeeds.
We should change our code to check if any one of these 3 is valid and if
so, handle the CVL (basically switching from AND to OR). The port name
field is definitely expected to be valid always.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Saurav Kashyap [Fri, 23 Aug 2019 09:52:38 +0000 (02:52 -0700)]
scsi: qedf: Add debug information for unsolicited processing
Log s_id, d_id, type and command to the log message.
[mkp: fixed warning]
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Saurav Kashyap [Fri, 23 Aug 2019 09:52:37 +0000 (02:52 -0700)]
scsi: qedf: Add support for 20 Gbps speed
The current code doeesn't support 20Gbps speed for current and supported
speed. Add support for it.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Saurav Kashyap [Fri, 23 Aug 2019 09:52:36 +0000 (02:52 -0700)]
scsi: qedf: Interpret supported caps value correctly
Driver was wrongly interpreting the supported cap value returned by qed.
Solution: Use QED define macros instead of OS defined for interpreting
supporting speeds.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Saurav Kashyap [Fri, 23 Aug 2019 09:52:35 +0000 (02:52 -0700)]
scsi: qedf: Add shutdown callback handler
Add shutdown callback handler.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Nilesh Javali [Fri, 23 Aug 2019 09:52:34 +0000 (02:52 -0700)]
scsi: qedf: Update module description string
Update module description.
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Arun Easi [Fri, 23 Aug 2019 09:52:33 +0000 (02:52 -0700)]
scsi: qedf: Fix crash during sg_reset
Driver was attempting to print cdb[0], which is not set for resets coming
from SCSI ioctls. Check for cmd_len before accessing cmnd.
Crash info:
[84790.864747] BUG: unable to handle kernel NULL pointer dereference at (null)
[84790.864783] IP: qedf_initiate_tmf+0x7a/0x6e0 [qedf]
[84790.865204] Call Trace:
[84790.865246] scsi_try_target_reset+0x2b/0x90 [scsi_mod]
[84790.865266] scsi_ioctl_reset+0x20f/0x2a0 [scsi_mod]
[84790.865284] scsi_ioctl+0x131/0x3a0 [scsi_mod]
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Saurav Kashyap [Fri, 23 Aug 2019 09:52:32 +0000 (02:52 -0700)]
scsi: qedf: Stop sending fipvlan request on unload
- On some setups fipvlan can be retried for long duration and the
connection to switch was not there so it was not getting any reply.
- During unload this thread was hanging.
Problem Resolution:
Check if unload is in progress, then quit from fipvlan thread.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Saurav Kashyap [Fri, 23 Aug 2019 09:52:31 +0000 (02:52 -0700)]
scsi: qedf: Print message during bailout conditions
Print messages during exiting condition to help debugging.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Don Brace [Thu, 22 Aug 2019 20:40:05 +0000 (15:40 -0500)]
scsi: smartpqi: bump version
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Gerry Morong <gerry.morong@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Don Brace [Thu, 22 Aug 2019 20:39:58 +0000 (15:39 -0500)]
scsi: smartpqi: update copyright
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Gilbert Wu [Thu, 22 Aug 2019 20:39:51 +0000 (15:39 -0500)]
scsi: smartpqi: add new pci ids
Add:
PM8222 VID_9005, DID_028F, SVID_1BD4 and SDID_004F
3101E-4i (1G, no GB) VID_9005, DID_028F, SVID_9005 and SDID_0808
3102E-8i (2G, no GB) VID_9005, DID_028F, SVID_9005 and SDID_0809
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Gilbert Wu <gilbert.wu@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Murthy Bhat [Thu, 22 Aug 2019 20:39:44 +0000 (15:39 -0500)]
scsi: smartpqi: correct REGNEWD return status
Return -EINPROGRESS when a rescan worker is queued.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Murthy Bhat <Murthy.Bhat@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Gilbert Wu [Thu, 22 Aug 2019 20:39:38 +0000 (15:39 -0500)]
scsi: smartpqi: add gigabyte controller
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Gilbert Wu <gilbert.wu@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Mahesh Rajashekhara [Thu, 22 Aug 2019 20:39:31 +0000 (15:39 -0500)]
scsi: smartpqi: correct hang when deleting 32 lds
When each ld is deleted, a rescan event is triggered in the driver. These
can stack up waiting on mutex_lock.
Change to mutex_try_lock and schedule a rescan for later.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Gilbert Wu [Thu, 22 Aug 2019 20:39:25 +0000 (15:39 -0500)]
scsi: smartpqi: add bay identifier
Return identify physical device "Phys_Bay_in_Box" as bay_identifier.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Gilbert Wu <gilbert.wu@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Murthy Bhat [Thu, 22 Aug 2019 20:39:18 +0000 (15:39 -0500)]
scsi: smartpqi: add sysfs entries
- serial number
- model
- vendor
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Murthy Bhat <Murthy.Bhat@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Dave Carroll [Thu, 22 Aug 2019 20:39:11 +0000 (15:39 -0500)]
scsi: smartpqi: add module param to hide vsep
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Gilbert Wu [Thu, 22 Aug 2019 20:39:04 +0000 (15:39 -0500)]
scsi: smartpqi: add pci ids for fiberhome controller
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Gilbert Wu <gilbert.wu@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Gilbert Wu [Thu, 22 Aug 2019 20:38:58 +0000 (15:38 -0500)]
scsi: smartpqi: add module param for exposure order
Expose physical devices before logical devices.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Gilbert Wu <gilbert.wu@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 28 Aug 2019 23:19:11 +0000 (16:19 -0700)]
scsi: lpfc: fix 12.4.0.0 GPF at boot
The 12.4.0.0 patch that merged WQ/CQ pairs into single per-cpu pair
contained a bug: a local variable was set to the queue pair by index. This
should have allowed the local variable to be natively used. Instead, the
code reused the index relative to the local variable, obtaining a random
pointer value that when used eventually faulted the system
Convert offending code to use local variable.
Fixes: c00f62e6c546 ("scsi: lpfc: Merge per-protocol WQ/CQ pairs into single per-cpu pair")
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Tested-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Tue, 27 Aug 2019 21:28:05 +0000 (14:28 -0700)]
scsi: lpfc: Remove bg debugfs buffers
Capturing and downloading dif command data and dif data was done a dozen
years ago and no longer being used. Also creates a potential security hole.
Remove the debugfs buffer for dif debugging.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
CC: KyleMahlkuch <kmahlkuc@linux.vnet.ibm.com>
CC: Hannes Reinecke <hare@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Tue, 27 Aug 2019 21:27:46 +0000 (14:27 -0700)]
scsi: lpfc: Resolve checker warning for lpfc_new_io_buf()
Per Dan Carpenter:
The patch
d79c9e9d4b3d: "scsi: lpfc: Support dynamic unbounded SGL lists on
G7 hardware." from Aug 14, 2019, leads to the following static checker
warning:
drivers/scsi/lpfc/lpfc_init.c:4107 lpfc_new_io_buf()
error: not allocating enough data 784 vs 768
There was no need to compare sizes nor to allocate size based on a define.
Change allocation to use actual structure length
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
CC: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
zhengbin [Mon, 26 Aug 2019 01:15:49 +0000 (09:15 +0800)]
scsi: ufs: remove set but not used variable 'val'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/ufs/ufs-qcom.c: In function ufs_qcom_pwr_change_notify:
drivers/scsi/ufs/ufs-qcom.c:808:6: warning: variable val set but not used [-Wunused-but-set-variable]
Fixes: 1e1e465c6d23 ("scsi/ufs: qcom: Remove ufs_qcom_phy_*() calls from host")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Acked-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Colin Ian King [Thu, 22 Aug 2019 21:56:51 +0000 (22:56 +0100)]
scsi: qla2xxx: fix spelling mistake "initializatin" -> "initialization"
There is a spelling mistake in a ql_log message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
projects / openwrt / staging / blogic.git / log