Ted Hess [Sat, 7 Jul 2018 20:11:48 +0000 (16:11 -0400)]
toolchain/nasm: Backport GCC8 compatibility fix from upstream repo
Signed-off-by: Ted Hess <thess@kitschensync.net>
(backported from
328ddcf628119733c511ec6cda06f2f0cc8d19ae)
Ademar Arvati Filho [Wed, 4 Jul 2018 01:29:36 +0000 (01:29 +0000)]
ramips: add support for Blueendless Kimax U35WF
Blueendless Kimax U35WF is a 3,5" HDD Enclosure with Wi-Fi and Ethernet
Patch rewritten from: https://forum.openwrt.org/viewtopic.php?id=66908
Based on: https://github.com/lede-project/source/pull/965
Specification:
- SoC: MediaTek MT7620N
- CPU/Speed: 580 MHz
- Flash-Chip: KH25L12835F Spi Flash
- Flash size: 16 MiB
- RAM: 64 MiB
- LAN: 1x 100 Mbps Ethernet
- WiFi SoC-integrated: 802.11bgn
- 1x USB 2.0
- UART: for serial console
Installation:
1. Download sysupgrade.bin
2. Open vendor web interface
3. Choose to upgrade firmware
3. After reboot connect via ethernet at 192.168.1.1
Signed-off-by: Ademar Arvati Filho <arvati@hotmail.com>
(backported from
16d6a63f857a4e9eeb1f173e964264d8a06e65eb)
Mathias Kresin [Thu, 5 Jul 2018 20:53:16 +0000 (22:53 +0200)]
ar71xx: drop unnecessary LOADER_TYPE variables
Drop the LOADER_TYPE variables in case no loader is used at all or move
the variable to devices which are using a loader.
Signed-off-by: Mathias Kresin <dev@kresin.me>
(backported from
b908c82f49c5049274f36345cfedbd21c0e5c938)
Mathias Kresin [Thu, 5 Jul 2018 20:48:54 +0000 (22:48 +0200)]
ar71xx: get rid of copy-file
Use the provided image build variables to point the kernel-bin build
command to the kernel we are interested in.
Signed-off-by: Mathias Kresin <dev@kresin.me>
(backported from
a0ec632f8d17cf75e2eca44ac3b3ede6d297f7fa)
Mathias Kresin [Wed, 4 Jul 2018 04:39:05 +0000 (06:39 +0200)]
ar71xx: mikrotik: cleanup nand image build code
Use the LOADER_TYPE variable to specify that we need the elf preloader
and append the loader via the corresponding build recipe. It allows to
enable initramfs images again for mikrotik NAND images, which caused a
build error before.
Add the minor header only to the kernel of the sysupgrade images, as it
is only required for the bootloader to find the kernel on flash.
Signed-off-by: Mathias Kresin <dev@kresin.me>
(backported from
5260c1003cee20b004f4628c72ef3985885ca901)
INAGAKI Hiroshi [Wed, 27 Jun 2018 13:47:13 +0000 (22:47 +0900)]
ramips: add support for I-O DATA WN-AX1167GR
I-O DATA WN-AX1167GR is a 2.4/5 GHz band 11ac router, based on
MediaTek MT7621A.
Specification:
- MT7621A (2-Cores, 4-Threads)
- 64 MB of RAM (DDR2)
- 16 MB of Flash (SPI)
- 2T2R 2.4/5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 2x LEDs, 4x keys (2x buttons, 1x slide switch)
- UART header on PCB
- Vcc, GND, TX, RX from ethernet port side
- baudrate: 115200 bps (U-Boot, OpenWrt)
Stock firmware:
In the stock firmware, WN-AX1167GR has two os images each composed of
Linux kernel and rootfs.
These images are stored in "Kernel" and "app" partition of the
following partitions, respectively.
(excerpt from dmesg):
MX25L12805D(c2
2018c220) (16384 Kbytes)
mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
Creating 10 MTD partitions on "raspi":
0x000000000000-0x000001000000 : "ALL"
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config "
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000000060000 : "iNIC_rf"
0x000000060000-0x0000007e0000 : "Kernel"
0x000000800000-0x000000f80000 : "app"
0x000000f90000-0x000000fa0000 : "Key"
0x000000fa0000-0x000000fb0000 : "backup"
0x000000fb0000-0x000001000000 : "storage"
The flag for boot partition is stored in "Key" partition, and U-Boot
reads this and determines the partition to boot.
If the image that U-Boot first reads according to the flag is
"Bad Magic Number", U-Boot then tries to boot from the other image.
If the second image is correct, change the flag to the number
corresponding to that image and boot from that image.
(example):
## Booting image at
bc800000 ...
Bad Magic Number,
FFFFFFFF
Boot from KERNEL 1 !!
## Booting image at
bc060000 ...
Image Name: MIPS OpenWrt Linux-4.14.50
Image Type: MIPS Linux kernel Image (lzma compressed)
Data Size:
1865917 Bytes = 1.8 MB
Load Address:
80001000
Entry Point:
80001000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
raspi_erase_write: offs:f90000, count:34
.
.
Done!
Starting kernel ...
Flash instruction using factory image:
1. Connect the computer to the LAN port of WN-AX1167GR
2. Connect power cable to WN-AX1167GR and turn on it
3. Access to "192.168.0.1" on the web browser and open firmware
update page ("ファームウェア")
4. Select the OpenWrt factory image and perform firmware update
5. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with sysupgrade image for WN-AX1167GR
6. Wait ~180 seconds to complete flasing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
(backported from
0b83a235602dace3de116a10de9515cda5b76be4)
Konstantin Demin [Thu, 28 Jun 2018 06:21:42 +0000 (09:21 +0300)]
libnl: bump to 3.4.0
refresh patches
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
(backported from
f715d816b754b74c24dc2dc9f62385fbc90f07b5)
Vladimir Vid [Thu, 26 Apr 2018 15:52:14 +0000 (17:52 +0200)]
uboot-imx: bump to 2018.03 which fixes the build issues with fdt64_t redefinitions
* change mx6qsabresd to mx6qsabres to match defconfig name
* merge wanboard profiles since there is only one defconfig for the target device
* move wanboard options from wandboard.h to defconfig
* remove legacy patches
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
(backported from
856cc6d9998ea717ee25d80bef52635dceeae71a)
Jeremiah McConnell [Wed, 20 Jun 2018 05:35:08 +0000 (23:35 -0600)]
config: add config option for KERNEL_TASKSTATS
In order for monitoring tools such as atop and htop to track and report
i/o data, kernel support for task statistics and io accounting is
required.
Add a config option to enable building this support in the kernel.
Signed-off-by: Jeremiah McConnell <miah@miah.com>
(backported from
206fbbfec2d0cc40266674e93e7e01e307847a6d)
Hauke Mehrtens [Sun, 24 Jun 2018 19:27:41 +0000 (21:27 +0200)]
mbedtls: Activate deterministic ECDSA
With deterministic ECDSA the value k needed for the ECDSA signature is
not randomly generated any more, but generated from a hash over the
private key and the message to sign. If the value k used in a ECDSA
signature or the relationship between the two values k used in two
different ECDSA signatures over the same content is know to an attacker
he can derive the private key pretty easily. Using deterministic ECDSA
as defined in the RFC6979 removes this problem by deriving the value k
deterministically from the private key and the content which gets
signed.
The resulting signature is still compatible to signatures generated not
deterministic.
This increases the size of the ipk on mips 24Kc by about 2 KByte.
old:
166.240 libmbedtls_2.11.0-1_mips_24kc.ipk
new:
167.811 libmbedtls_2.11.0-1_mips_24kc.ipk
This does not change the ECDSA performance in a measurable way.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(backported from
b19622044d492e9eff9d880d6bc1fc9486774886)
(rebased patches)
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Daniel Engberg [Sun, 24 Jun 2018 19:19:18 +0000 (21:19 +0200)]
mbedtls: Disable MBEDTLS_SHA256_SMALLER implementation
Disable MBEDTLS_SHA256_SMALLER implementation, not enabled by default in
upstream and reduces performance by quite a bit.
Source: include/mbedtls/config.h
Enable an implementation of SHA-256 that has lower ROM footprint but also
lower performance.
The default implementation is meant to be a reasonnable compromise between
performance and size. This version optimizes more aggressively for size at
the expense of performance. Eg on Cortex-M4 it reduces the size of
mbedtls_sha256_process() from ~2KB to ~0.5KB for a performance hit of
about 30%.
The size of mbedtls increased a little bit:
ipkg for mips_24kc before:
164.382 Bytes
ipkg for mips_24kc after:
166.240 Bytes
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
(backported from
5a078180d08db8d4261119cd396a38b0261bfc5b)
(rebased patches)
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Daniel Engberg [Fri, 22 Jun 2018 18:55:15 +0000 (20:55 +0200)]
sunxi: Enable SD block devices
USB storage support is however SCSI Disk block device support isn't
meaning that connected devices wont enumerate.
Enable CONFIG_BLK_DEV_SD by default to fix it.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
(backported from
3accbc6aacae62c83ddf010f9b095fb7a3d69f05)
Alexandru Ardelean [Mon, 25 Jun 2018 12:03:04 +0000 (15:03 +0300)]
brcm2708: platform.sh: fix tar directory directive
BusyBox's `tar` command does not support the `--directory` directive, which
is essentially `-C` in short-form option.
BusyBox's `tar` command supports `-C`.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
(backported from
7de50d19171b94642025dd55dd96b2c09c1e9762)
Enrico Mioso [Sun, 1 Jul 2018 20:46:05 +0000 (22:46 +0200)]
libconfig: update to version 1.7.2
The previous link did not work here.
Compile-tested on: bcm47xx
Runtime-tested on: bcm47xx
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
(backported from
231b0177fb235767e49cdee067b7db0ed2691548)
Luis Araneda [Tue, 3 Jul 2018 02:54:11 +0000 (22:54 -0400)]
kernel: remove DEVMEM and DEVKMEM from target's config
These options are handled by generic configuration
Targets that need these options should select KERNEL_DEVMEM
and/or KERNEL_DEVKMEM options on OpenWRT's config
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
(backported from
8f60c3d57149a2bb04fde9798edc45d659ed7c17)
Felix Fietkau [Sat, 7 Jul 2018 12:50:51 +0000 (14:50 +0200)]
toolchain/nasm: fix missing AR/RANLIB variables
Fixes build on macOS
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(backported from
d3a7587eb95e6e8c85ff0e57504bc31d1e1b8523)
Felix Fietkau [Thu, 5 Jul 2018 13:11:07 +0000 (15:11 +0200)]
perf: remove linux 4.4 workarounds
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(backported from
bf136c637c02c154c14bbf48ac2c07467d948ac7)
Ted Hess [Thu, 28 Jun 2018 23:28:02 +0000 (19:28 -0400)]
toolchain: Replace YASM with NASM
Packages libx264 and ffmpeg are built with ASM options on x86 platforms.
The current libx264 version no longer builds with YASM and requires NASM.
ffmpeg 3.x can be built with either YASM or NASM however, furture 4.x versions
will require NASM.
Signed-off-by: Ted Hess <thess@kitschensync.net>
Acked-by: Rosen Penev <rosenp@gmail.com>
(backported from
0f543883cd0505a98fdc680ce2f08cbfca6d52a7)
Yousong Zhou [Fri, 29 Jun 2018 06:40:46 +0000 (14:40 +0800)]
download.mk: enable DownloadMethod/github_archive
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
(backported from
9009efa18b45b4b573111fafa777f7b642486e3e)
Yousong Zhou [Thu, 28 Jun 2018 10:27:27 +0000 (18:27 +0800)]
scripts/dl_github_archive.py: rename from download.py
- Make the code more GitHub-specific
- Requires mirror hash to work with .gitattributes
- Use different API depending on whether PKG_SOURCE_VERSION is a
complete commit id or other ref types like tags
- Fix removing symbolic link
- pre-clean dir_untar for possible leftovers from previous run
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
(backported from
04b9f8587370f96366c6e53fb411473279ba7c02)
Yousong Zhou [Tue, 3 Jul 2018 08:15:35 +0000 (16:15 +0800)]
download.mk: add more comments
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
(backported from
e48ea13b3bac5393d6400156ddb066ec5de2ea4e)
Luiz Angelo Daros de Luca [Sun, 17 Jun 2018 09:08:51 +0000 (06:08 -0300)]
elfutils: bump to 0.173
- Removed hacks to use standalone argp as upstream now detects it nicely.
- As we are already installing files, use files from PKG_INSTALL_DIR and
not PKG_BUILD_DIR
- Only changes Makefile.am as PKG_FIXUP:=autoreconf is in use
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
(backported from
b724443f9f4c8d691fc0e7355e1388920cdb9b96)
Romain MARIADASSOU [Tue, 26 Jun 2018 23:24:39 +0000 (01:24 +0200)]
ramips: add support for TL-WA801ND v5
Specification:
- System-On-Chip: MediaTek MT7628NN
- CPU/Speed: 580 MHz
- Flash-Chip: ELM Technology GD25Q64
- Flash size: 8192 KiB
- RAM: 64 MiB
- Wireless No1: SoC-integrated: MT7628N 2.4GHz 802.11bgn
Currently the only method to install openwrt for the first time is via
TFTP recovery. After first install you can use regular updates.
Flash instructions:
1) To flash the recovery image, start a TFTP server with IP address
192.168.0.66 and serve the recovery image named tp_recovery.bin.
2) Connect your device to the LAN port, then press the WPS and Reset
button and power it up. Keep pressing the WPS/Reset button for
10 seconds or until the lock LED is lighting up.
It will try to download the recovery image and flash it.
It can take up to 2-3 minutes to finish. When it reaches 100%, the
router will reboot itself.
Signed-off-by: Romain MARIADASSOU <roms2000@free.fr>
(backported from
ce31bdc20c3f2eb387a84c277dff76324a8e39c7)
Maxim Anisimov [Sun, 8 Apr 2018 14:04:11 +0000 (17:04 +0300)]
ramips: add support for ZyXEL Keenetic Extra II
Specification:
- System-On-Chip: MT7628N/N
- CPU/Speed: 580 MHz
- Flash-Chip: Winbond w25q256
- Flash size: 32768 KiB
- RAM: 128 MiB
- 5x 10/100 Mbps Ethernet
- 4x external, non-detachable antennas
- UART (J1) header on PCB (57600 8n1)
- Wireless No1 (2T2R): SoC-integrated: MT7628N 2.4GHz 802.11bgn
- Wireless No2 (2T2R): On-board chip: MT7612EN 5GHz 802.11ac
- USB: Yes 1 x 2.0
- 4x LED, 3x button
The device supports dual boot mode. So we use only first half of flash.
Flash instruction:
The only way to flash OpenWrt image is to use
tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-zyxel_keenetic-extra-ii-squashfs-factory.bin"
to "kextra2_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed until power led start blinking.
4. Router will download file from server, write it to flash and reboot.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
(backported from
7d07bc96b7e686244ed096d3bbfad297a2ec1ce9)
Maxim Anisimov [Thu, 28 Jun 2018 05:26:39 +0000 (08:26 +0300)]
ramips: move zyimage define to common Makefile
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
(backported from
9e2c28472c3f3a76e16afb582fd8807d08c6dda6)
Tobias Schramm [Mon, 25 Jun 2018 20:51:43 +0000 (22:51 +0200)]
ramips: add support for MikroTik RouterBOARD RBM11g
This commit adds support for the MikroTik RouterBOARD RBM11g.
=Hardware=
The RBM11g is a mt7621 based device featuring one GbE port and one
miniPCIe slot with a sim card socket and USB 2.0.
==Switch==
The single onboard Ethernet port is connected the CPU directly.
The internal switch of the mt7621 SoC is disabled.
==Flash==
The device has one spi nor flash chip. It is a 128 Mbit winbond 25Q128FVS
connected to CS0.
==PCIe==
The board features a single miniPCIe slot. It has a dedicated mini SIM
socket and a USB 2.0 port. Power to the miniPCIe slot is controlled via
GPIO9.
==USB==
There are no external USB ports.
==Power==
The board can accept both, passive PoE and external power via a 2.1 mm
barrel jack (center-positive). The input voltage range is 11-32 V.
==Serial port==
The device does have an onboard UART on an unpopulated header next to the
flash chip:
GND: pin 2
TX: pin 7
RX: pin 6
Settings: 115200, 8N1
See below illustration for positioning of the header.
0 = screw hole
* = some pin
T = TX pin
R = RX pin
G = GND pin
Pinout:
+---------------
|O
| __
| / \
| \__/
|
|
|
| +---+
| |RAM|
| +--+ | |
| |**| <- unpopulated header with UART
| |*T| +---+
| |R*| +--------+
| |**| | |
| |G*| | CPU |
| +--+ | |
| +--+ | |
| | | +--------+
| +--+ <- flash chip
|O
| +-----+
| | |
|+--+ | |
|| | | |
+---------------------
=Installation=
To install an OpenWRT image to the device two components must be built:
1. A openwrt initramfs image
2. A openwrt sysupgrade image
===initramfs & sysupgrade image===
Select target devices "Mikrotik RBM11G" in
openwrt menuconfig and build the images. This will create the images
"openwrt-ramips-mt7621-mikrotik_rbm11g-initramfs-kernel.bin" and
"openwrt-ramips-mt7621-mikrotik_rbm11g-squashfs-sysupgrade.bin" in the
output directory.
==Installing==
**Make sure to back up your RouterOS license in case you do ever want to
go back to RouterOS using "/system license output" and back up the
created license file.**
When rebooted the board will try booting via ethernet first. If your
board does not boot via ethernet automatically you will have to attach
to the serial port and set ethernet as boot device within RouterBOOT.
1. Set up a dhcp server that points the bootfile to tftp server serving
the "openwrt-ramips-mt7621-mikrotik_rbm11g-initramfs-kernel.bin"
initramfs image
2. Connect to ethernet port on board
3. Power on the board
4. Wait for OpenWrt to boot
Right now OpenWrt will be running with a SSH server listening. Now
OpenWrt must be flashed to the devices flash:
1. Copy "openwrt-ramips-mt7621-mikrotik_rbm11g-squashfs-sysupgrade.bin"
to the device using scp.
2. Write openwrt to flash using "sysupgrade
openwrt-ramips-mt7621-mikrotik_rbm11g-squashfs-sysupgrade.bin"
Once the flashing completes the board will reboot. Disconnect from the
devices ethernet port or stop the DHCP/TFTP server to prevent the device
from booting via ethernet again.
The device should now boot straight to OpenWrt.
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
(backported from
faf64056ddd46992a75b1e277d94541c7251035c)
Michael Kuron [Sun, 1 Jul 2018 08:03:38 +0000 (10:03 +0200)]
lantiq: enlarge AVM Fritz!Box 3370 flash
Increase the available flash memory size in AVM Fritz!Box 3370 by
incorporating the unused extra partitions located after the ubi partition.
Note that users upgrading from a previous OpenWRT version need to
re-install from the boot loader to pick up the new partition layout.
Available flash space for rootfs+overlay increases from 48MB to 124MB.
Reverting to the OEM firmware is still possible (via the recovery utility
provided by AVM) as the OEM firmware appears to reformat the config and
nand-filesystem partitions upon first boot if necessary. The
reserved-kernel and reserved-filesystem partitions are overwritten by the
OEM firmware when installing an update, so their contents do not matter.
Boot loader and device-specific information (MAC addresses, calibration
data, etc.) are not located in NAND flash and remain unharmed by this
changed.
Tested with OEM firmware 06.54 on device with HWRevision 5 and Micron
flash chip.
Signed-off-by: Michael Kuron <m.kuron@gmx.de>
(backported from
d0b89e48d712725c341842e60aadf802b6debc29)
Hyeonsik Song [Mon, 25 Jun 2018 02:02:43 +0000 (11:02 +0900)]
firmware-utils: tplink-safeloader: add calloc error handling
Signed-off-by: Hyeonsik Song <blogcin@naver.com>
(backported from
c2766270efcba795f1d14f9a51f07898eb8a62c1)
Luis Araneda [Sat, 30 Jun 2018 07:15:55 +0000 (03:15 -0400)]
zynq: remove config options handled by generic
The options are now handled for all targets by
the generic configuration
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
(backported from
efa112261bf8086014272dd2ba5d2d31257cc288)
Yousong Zhou [Fri, 29 Jun 2018 05:49:34 +0000 (13:49 +0800)]
download.mk: restore the old dl_method implementation
Seems like the python download.py dl_method call causes serious
performance regression for fresh "make defconfig" as reported in
FS#1621. GitHub tarball download will also be disabled with this
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
(backported from
e15565a01cea6a61c537f5fb91c4e4d27fb7b290)
Stefan Lippers-Hollmann [Thu, 28 Jun 2018 12:04:46 +0000 (14:04 +0200)]
ipq806x: switch the NBG6817 wlan LEDs from amber to white
The original device support patch configured the amber wlan LEDs (which
are meant as error indicator by the OEM) controlled by the SOC's GPIO
as wlan traffic indicators, as the correct white wlan LEDs are
connected to GPIOs controlled by the QCA9984/ ath10k wlan cards were
not accessible. The recent addition of GPIO/ LED support to ath10k now
makes it possible to use the correct white LEDs instead - and
"mac80211: ath10k: use tpt LED trigger by default" also enables them by
default. While both LEDs are independent of each other (two separate
LEDs sharing one light tunnel), triggering both on wlan traffic is not
the intended behaviour (bright yellow light).
Tested on the ZyXEL NBG6817.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
(backported from
7c7ca66109468b57f06d20eafbb9523aecc91706)
Yousong Zhou [Wed, 27 Jun 2018 07:20:21 +0000 (15:20 +0800)]
scripts/download.py: use a more terse api for fetching git commit date
The previous api [1] includes in its response patch data among other
things, as such the response size can vary and be big. Use another
api[2] to improve it a bit
[1] Get a single commit, Repositories, https://developer.github.com/v3/repos/commits/#get-a-single-commit
[2] Git Commits, Git Data, https://developer.github.com/v3/git/commits/#get-a-commit
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
(backported from
6e3c2d757a5745dee5cce0b53175b56ad3621d73)
Alberto Bursi [Mon, 18 Jun 2018 17:49:16 +0000 (19:49 +0200)]
uboot-kirkwood: fix whitespaces
remove whitespaces from the patches
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
(backported from
ccd1dc3d2044b3cf624f93c86e127f55c5632231)
Yousong Zhou [Sun, 11 Feb 2018 09:42:22 +0000 (17:42 +0800)]
build: download code from github using archive API
A new python script scripts/download.py is added to fetch tarballs using
GitHub archive API [1], then repack in a reproducible way same as the
current DownloadMethod/git
GitHub imposes a 60 reqs/hour rate limit on unauthenticated API
access[2]. This affects fetching commit date for feeding tar --mtime=
argument. However, observation indicates that archive download is NOT
subject to this limit at the moment. In the rare cases where download
fails because of this, we will falback to using DownloadMethod/git
The missing piece in the GitHub API is that it cannot provide in the
tarball dependent submodules's source code. In that case, the
implementation will also fallback to using DownloadMethod/git
[1] Get archive link, https://developer.github.com/v3/repos/contents/#get-archive-link
[2] Rate limiting, https://developer.github.com/v3/#rate-limiting
v2 <- v1:
- allow passing multiple urls with --urls argument
- add commit ts cache. can be helpful on retry
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
(backported from
75ab064d2b38e70746af1718ed7cdbafb906249e)
Daniel Engberg [Sat, 9 Jun 2018 20:25:25 +0000 (22:25 +0200)]
package/utils/e2fsprogs: Update to 1.44.2
Update e2fsprogs to 1.44.2
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
(backported from
1b46bce8509180914d2f44ea2374e41b6bbc0752)
Christian Lamparter [Thu, 21 Jun 2018 12:24:59 +0000 (14:24 +0200)]
ipq40xx: add support for the ZyXEL NBG6617
This patch adds support for ZyXEL NBG6617
Hardware highlights:
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB DDR3L-1600/1866 Nanya NT5CC128M16IP-DI @ 537 MHz
NOR: 32 MiB Macronix MX25L25635F
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: RESET Button, WIFI/Rfkill Togglebutton, WPS Button
LEDS: Power, WAN, LAN 1-4, WLAN 2.4GHz, WLAN 5GHz, USB, WPS
Serial:
WARNING: The serial port needs a TTL/RS-232 3.3v level converter!
The Serial setting is 115200-8-N-1. The 1x4 .1" header comes
pre-soldered. Pinout:
1. 3v3 (Label printed on the PCB), 2. RX, 3. GND, 4. TX
first install / debricking / restore stock:
0. Have a PC running a tftp-server @ 192.168.1.99/24
1. connect the PC to any LAN-Ports
2. put the openwrt...-factory.bin (or V1.00(ABCT.X).bin for stock) file
into the tftp-server root directory and rename it to just "ras.bin".
3. power-cycle the router and hold down the the WPS button (for 30sek)
4. Wait (for a long time - the serial console provides some progress
reports. The u-boot says it best: "Please be patient".
5. Once the power LED starts to flashes slowly and the USB + WPS LEDs
flashes fast at the same time. You have to reboot the device and
it should then come right up.
Installation via Web-UI:
0. Connect a PC to the powered-on router. It will assign your PC a
IP-address via DHCP
1. Access the Web-UI at 192.168.1.1 (Default Passwort: 1234)
2. Go to the "Expert Mode"
3. Under "Maintenance", select "Firmware-Upgrade"
4. Upload the OpenWRT factory image
5. Wait for the Device to finish.
It will reboot into OpenWRT without any additional actions needed.
To open the ZyXEL NBG6617:
0. remove the four rubber feet glued on the backside
1. remove the four philips screws and pry open the top cover
(by applying force between the plastic top housing from the
backside/lan-port side)
Access the real u-boot shell:
ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02"
When the device is starting up, the user can enter the the loader shell
by simply pressing a key within the 3 seconds once the following string
appears on the serial console:
| Hit any key to stop autoboot: 3
The user is then dropped to a locked shell.
|NBG6617> HELP
|ATEN x[,y] set BootExtension Debug Flag (y=password)
|ATSE x show the seed of password generator
|ATSH dump manufacturer related data in ROM
|ATRT [x,y,z,u] RAM read/write test (x=level, y=start addr, z=end addr, u=iterations)
|ATGO boot up whole system
|ATUR x upgrade RAS image (filename)
|NBG6617>
In order to escape/unlock a password challenge has to be passed.
Note: the value is dynamic! you have to calculate your own!
First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env)
to get the challange value/seed.
|NBG6617> ATSE NBG6617
|
012345678901
This seed/value can be converted to the password with the help of this
bash script (Thanks to http://www.adslayuda.com/Zyxel650-9.html authors):
- tool.sh -
ror32() {
echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) ))
}
v="0x$1"
a="0x${v:2:6}"
b=$(( $a + 0x10F0A563))
c=$(( 0x${v:12:14} & 7 ))
p=$(( $(ror32 $b $c) ^ $a ))
printf "ATEN 1,%X\n" $p
- end of tool.sh -
|# bash ./tool.sh
012345678901
|
|ATEN 1,
879C711
copy and paste the result into the shell to unlock zloader.
|NBG6617> ATEN 1,
0046B0017430
If the entered code was correct the shell will change to
use the ATGU command to enter the real u-boot shell.
|NBG6617> ATGU
|NBG6617#
Co-authored-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
(backported from
82618062cf7ed6b40d2c52c6f6b96364888ffda6)
Philip Prindeville [Tue, 26 Jun 2018 04:34:49 +0000 (22:34 -0600)]
iperf3: update to 3.6
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
(backported from
d375d5fafefb4de453ee36108b64f8df49aa2bec)
Alex Maclean [Wed, 20 Jun 2018 13:56:22 +0000 (14:56 +0100)]
firmware-utils: tplink-safeloader: switch RE350 to dynamic partitions
Use the new dynamic partition split in tplink-safeloader so we no longer
have to worry about kernel size increases.
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
(backported from
97da92b1277a40fa7daf354ed52b8ea25e06a779)
Alex Maclean [Wed, 20 Jun 2018 13:56:21 +0000 (14:56 +0100)]
ramips: RE350: add rootfs offset to header
Have mktplinkfw fill in the rootfs offset so the firmware splitter can
find it without aligning to erase blocks.
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
(backported from
2f23a0583a3092d9076ceecca16be0f8ccdce217)
Alex Maclean [Wed, 20 Jun 2018 13:56:20 +0000 (14:56 +0100)]
firmware-utils: tplink-safeloader: add dynamic partitions
Add support to dynamically split the firmware partition into os-image
and file-system partitions. This is done by replacing those entries in
the partition table with a single unified firmware partition, which is
then split according to actual kernel image size.
The factory image will have the file-system partition aligned to a 64K
erase block, but the sysupgrade image skips this and aligns only the
JFFS2 EOF marker to squeeze out more space.
This should prevent further creeping updates to the kernel partition
size while maximizing space for the overlay filesystem on smaller
devices.
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
(backported from
408c54b02f6a6dd2c0ae30a7885a37c9ac4c1b53)
Alex Maclean [Wed, 20 Jun 2018 13:56:19 +0000 (14:56 +0100)]
firmware-utils: mktplinkfw: add rootfs offset for combined images
Add an option (-O) to calculate rootfs offset for combined images.
This is needed for the TP-Link mtdsplit driver to locate the rootfs
when the start is not aligned to an erase block. This will be the
case for sysupgrade images produced by tplink-safeloader with upcoming
dynamic partition splitting.
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
(backported from
0a2f21fa715bcf2e2975e32a1843a13fa088c640)
Stijn Tintel [Fri, 22 Jun 2018 11:42:20 +0000 (14:42 +0300)]
mac80211: enable ath10k LED support by default
Commit
61d57a2f88b90ba951012e66c7c6fae9234c97b4 adds ath10k LED
support, but doesn't add an option to actually enable it.
After enabling this option, a LED named ath10k-phy0 appears in sysfs,
and a trigger can be assigned to it. Since
60deb3cdef4a the default set
trigger is the tpt one.
Enable it by default, as most devices using ath10k chips shouldn't be
severely space-constrained. There are likely many devices that can
benefit from having it enabled, like my testing device.
Before:
text data bss dec hex filename
245311 8899 16 254226 3e112 ath10k_core.ko
After:
text data bss dec hex filename
245979 8899 16 254894 3e3ae ath10k_core.ko
Tested on a D-Link DAP-2695-A1 (ar71xx).
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(backported from
34e22653ac18b6ac7fd368ca47625f665808067f)
Mathias Kresin [Fri, 22 Jun 2018 17:11:08 +0000 (19:11 +0200)]
mac80211: ath10k: use tpt LED trigger by default
Use the tpt LED trigger for each created phy led. Ths way LEDs attached
to the ath10k GPIO pins are indicating the phy status and blink on
traffic.
Signed-off-by: Mathias Kresin <dev@kresin.me>
(backported from
60deb3cdef4ac50a7d0fe9964a0f4a55aca1567e)
Franz Flasch [Thu, 17 May 2018 09:57:00 +0000 (11:57 +0200)]
ramips: add support for TP-Link Archer C2
Specification:
- System-On-Chip: MT7620A
- CPU/Speed: 580 MHz
- Flash-Chip: Winbond 25Q64BVSIG
- Flash size: 8192 KiB
- RAM: 64 MiB
- Wireless No1: SoC-integrated: MT7620A 2.4GHz 802.11bgn
- Wireless No2: On-board chip: MT7610EN 5GHz 802.11ac
- Switch: RTL8367RB Gigabit Switch
- USB: Yes 1 x 2.0
Preparing a TFTP recovery image for initial flashing:
Currently the only method to install openwrt for the first time is via
TFTP download in u-boot. After first install you can use regular updates.
WARNING: This method also overwrites the bootloader partition!
Create a TFTP recovery image:
1) Download a stock TP-Link Firmware file here:
https://www.tp-link.com/en/download/Archer-C2_V1.html#Firmware
2) Extract u-boot from the binary file:
#> dd if=c2v1_stock_firmware.bin of=c2v1_uboot.bin bs=1 skip=512 count=131072
3) Now merge the sysupgrade image and the u-boot into one binary:
#> cat c2v1_uboot.bin openwrt-squashfs-sysupgrade.bin > ArcherC2V1_tp_recovery.bin
The resulting image can be flashed via TFTP recovery mode.
Flash instructions:
1) To flash the recovery image, start a TFTP server from IP address
192.168.0.66 and serve the recovery image named
ArcherC2V1_tp_recovery.bin.
2) Connect your device to the LAN port, then press the WPS/Reset button
and power it up. Keep pressing the WPS/Reset button for 10 seconds.
It will try to download the recovery image and flash it.
It can take up to 20-25 minutes to finish. When it reaches 100%, the
router will reboot itself.
Signed-off-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Franz Flasch <franz.flasch@gmx.at>
(backported from
8375623a064037bbdd914bd9e7529eefa7172560)
Franz Flasch [Thu, 17 May 2018 09:51:38 +0000 (11:51 +0200)]
ramips: fix ZyXEL Keenetic Viva switch config
The rtl8367b driver never supported a mdio property and it is quite
likely that the switch never worked for the board.
Use the mii-bus property instead to manage the switch via a mdio bus.
Signed-off-by: Franz Flasch <franz.flasch@gmx.at>
(backported from
abb7524683cbc0185ee2d0b590c045065de354b7)
Franz Flasch [Thu, 17 May 2018 09:51:38 +0000 (11:51 +0200)]
kernel: rtl8366-smi: add Realtek switch management via mii-bus
Current version of rtl8366-smi module only supports Realtek switch
managment via two gpio lines. This adds Realtek switch
management via mii_bus. Tested on a Tp-link Archer C2 v1 (Mediatek
SoC mt7620a based)
dts-file configuration should look like this:
rtl8367rb {
compatible = "realtek,rtl8367b";
realtek,extif1 = <1 0 1 1 1 1 1 1 2>;
mii-bus = <&mdio0>;
};
ðernet {
status = "okay";
mtd-mac-address = <&rom 0xf100>;
pinctrl-names = "default";
pinctrl-0 = <&rgmii1_pins &rgmii2_pins &mdio_pins>;
port@5 {
status = "okay";
mediatek,fixed-link = <1000 1 1 1>;
phy-mode = "rgmii";
};
mdio0: mdio-bus {
status = "okay";
};
};
Signed-off-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Franz Flasch <franz.flasch@gmx.at>
(backported from
d4ac26ec4920036fe15414e47a0f1a3df6e8b9fb)
Mathias Kresin [Wed, 20 Jun 2018 20:10:50 +0000 (22:10 +0200)]
kernel: rtl8367b: drop redundant compatible
Remove the compatible without vendor prefix. It is formal wrong and not
used in the tree.
Signed-off-by: Mathias Kresin <dev@kresin.me>
(backported from
f9e7f193344fcee585b454e3884297f721187f4a)
Stijn Tintel [Tue, 19 Jun 2018 17:58:51 +0000 (20:58 +0300)]
kernel: define THERMAL_EMERGENCY_POWEROFF_DELAY_MS
Enabling CONFIG_ATH10K_THERMAL on targets that don't have CONFIG_THERMAL
enabled in their kernel config causes build to fail due to missing
symbol THERMAL_EMERGENCY_POWEROFF_DELAY_MS. Add it to kmod-thermal.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(backported from
f9a42ae2d707b63b2bbe72945a2816da7d4fe30c)
Daniel Golle [Thu, 21 Jun 2018 10:00:12 +0000 (12:00 +0200)]
ltq-vdsl-fw: fix ltq-vdsl-vr9-vectoring-fw-installer package install
The package is not being generated otherwise, which is fatal because
it is part of the subtargets default package set...
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(backported from
a704a2c06f13ade699d24616322a1339c4321cb5)
Christo Nedev [Wed, 20 Jun 2018 19:29:39 +0000 (19:29 +0000)]
brcm2708: Add wifi driver, firmware and NVRAM for Raspberry Pi 3 b
2708 -> 43430 -> pi0w
2709 -> 43430 -> pi3b
2709 -> 43455 -> pi3bplus
2710 -> 43430 -> pi3b
2710 -> 43455 -> pi3bplus
Signed-off-by: Christo Nedev <christo.nedev@gmail.com>
(backported from
48f311a112b63a54c7d17e4fa1537dff1ac12219)
Daniel Engberg [Tue, 19 Jun 2018 06:44:54 +0000 (08:44 +0200)]
octeon: Add and set CPU type Octeon+ as default
The lowest CPU type used by supported Octeon platform
is Octeon+ (EdgeRouter Lite) while EdgeRouter Pro/ER-8 uses
Octeon II which is backwards compatible with Octeon+.
Sources:
https://community.ubnt.com/t5/EdgeRouter/EdgeRouter-Pro-CPU/td-p/654599
https://www.cavium.com/octeon-II-CN68XX.html
"OCTEON II family is fully software compatible with the widely-adopted
OCTEON Plus family"
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
(backported from
c6e02b49f65cb4eff624a0831d3db265b3fadd2a)
Daniel Golle [Wed, 20 Jun 2018 12:38:13 +0000 (14:38 +0200)]
ltq-vdsl-fw: add meaningful version information
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(backported from
3d20bee2cd11f83400e925870a03fb47cedceae3)
Daniel Golle [Wed, 20 Jun 2018 09:16:54 +0000 (11:16 +0200)]
brcm2708: Add wifi driver, firmware and NVRAM for RPi1
Apparently there are RPi1 devices with BRCM43430 wifi, such as the
Pi Zero W. Add the necessary packages for that to the image generated
for those boards as well.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(backported from
969fe206bdb910789bebd064d4b3be00238b0012)
Daniel Golle [Tue, 19 Jun 2018 15:55:22 +0000 (17:55 +0200)]
ltq-vdsl-fw: add nonshared flag
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(backported from
512c57e7f3aa3cde0889a517f5f4c01783a3a57a)
Evgeniy Didin [Tue, 19 Jun 2018 10:40:54 +0000 (13:40 +0300)]
arc770: bump kernel to 4.14
Currently arc770 is no more "source-only".
Lets update Linux kernel version from 4.9 to 4.14 for arc770.
config-4.14 was simply regenerated with "make kernel_menuconfig".
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: John Crispin <john@phrozen.org>
(backported from
56f3aee53149c82687fb90b2551defea6d0df8e9)
David Ehrmann [Sun, 10 Jun 2018 01:33:24 +0000 (18:33 -0700)]
ar71x: add support for Mikrotik Routerboard wAP R
This commit adds support for the Mikrotik wAP R (RBwAPR-2nD). The change
is based on
3b15eb0 which added support for the wAP 2nD. This change lacks
LED support.
Specifications:
- SoC: Qualcomm QCA9531 (650 MHz)
- RAM: 64 MB
- Storage: 16 MB NOR SPI flash
- Wireless: built-in QCA9531, 802.11b/g/n 2x2:2
- Ethernet: 1x100Mbps
- Power: 9-30V Passive PoE, 9-30V DC jack, 9-30V automotive jack
- SIM card slot
- Mini-PCIe slot
Installation:
1. Login to the Mikrotik WebUI to backup your licence key
2. Change the following settings in System->Routerboard->Settings:
- Boot device: try ethernet once then NAND
- Boot protocol: DHCP
- Force Backup Booter: checked
3. Setup a DHCP/BOOTP server with:
- DHCP-Option 66 (TFTP server name) pointing to a local TFTP
server within the same subnet of the DHCP range
- DHCP-Option 67 (Bootfile-Name) matching the initramfs filename
of the to be booted image, e.g.
openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf
4. Power off the device
5. If this is the second attempt to boot OpenWRT or the boot device isn't
"try ethernet once then NAND," press and hold the reset button while
powered off. If this is the first attempt, this step isn't necessary.
6. Power on the device, holding the reset button for 15-20s if already
pressed from the previous step.
The board should load and start the initramfs image from the TFTP
server. Login as root/without password to the started OpenWRT via SSH
listing on IPv4 address 192.168.1.1. Use sysupgrade to install OpenWRT.
Revert to RouterOS
Use the "rbcfg" package on in OpenWRT:
- rbcfg set boot_protocol bootp
- rbcfg set boot_device ethnand
- rbcfg apply
Open Netinstall and reboot routerboard. Now Netinstall sees RouterBOARD
and you can install RouterOS. If NetInstall gets stuck on Sending offer
just wait for it to timeout and then close and open Netinstall again.
Click on install again.
In order for RouterOS to function properly, you need to restore license
for the device. You can do that by including license in NetInstall.
Signed-off-by: David Ehrmann <ehrmann@gmail.com>
(backported from
81d446b045176e3e25bb0ef74e3d060b51a0a353)
Felix Fietkau [Wed, 6 Jun 2018 07:56:13 +0000 (09:56 +0200)]
ramips: improve ethernet driver performance with GRO/TSO
GRO stores packets as fraglist. If they are routed back to the ethernet
device, they need to be re-segmented if the driver does not support
sending fraglists.
Add the missing support for that, along with a missing feature flag that
allows full routed GRO->TSO offload.
Considerably reduces CPU utilization for routing
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(backported from
9a4253b81f3b3fff833ef92737ef73ad4c455ade)
Hauke Mehrtens [Mon, 18 Jun 2018 20:49:21 +0000 (22:49 +0200)]
kernel/modules: kmod-chaoskey: Add missing dependency
This new package was missing the dependency to kmod-random-core which
caused some build errors.
Fixes: 163ab9135a9 ("kernel/modules: add chaoskey module, hardware TRNG")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(backported from
d661a5d754d1fb4731a5524a20c8c24eaf59f627)
Kevin Darbyshire-Bryant [Mon, 18 Jun 2018 18:01:07 +0000 (18:01 +0000)]
ltq_atm: burn ifx_atm_alloc_tx with fire
Drop code that was never used.
Tested on: BT HomeHub 5a
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
(backported from
83f31b794737adff3604474f0d09135fb3359ee5)
Krystian Kozak [Sun, 27 May 2018 19:58:07 +0000 (21:58 +0200)]
b43-tools: update to latest git HEAD
122ca37 Rename bits in hostflags to match new identifiers for the hostflags
32c2a3c Change order of identifiers to be ascending with the spr numbers
f7016b5 Remove definitions which are not Broadcom specific
b77c0a3 debug: Fix ordering of HF bits
3f46e61 fwcutter: Add firmware 9.10.178.27
27892ef fwcutter/make: Avoid _DEFAULT_SOURCE warning
Signed-off-by: Krystian Kozak <krystian.kozak20@gmail.com>
(backported from
142477e75112f0c3a21d43a1b36922d46c67bd33)
Hannu Nyman [Sun, 17 Jun 2018 18:11:44 +0000 (21:11 +0300)]
mvebu: enable CONFIG_HW_RANDOM
Enable the Hardware Random Number Generator Core infrastructure
in kernel.
Needed for hardware random number generator drivers like chaoskey
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
(backported from
414ce80c074142be4933978fcce7cb530b63c863)
Hannu Nyman [Sun, 17 Jun 2018 17:54:41 +0000 (20:54 +0300)]
kernel/modules: add chaoskey module, hardware TRNG
Package the driver for Chaoskey, a USB dongle that provides a
True Random Number Generator (TRNG) and feeds entropy to kernel.
Chaoskey driver is included the upstream Linux sources, so
only packaging it is needed.
Run-tested with ipq806x/R7800 and mvebu/WRT3200ACM.
(Requires CONFIG_HW_RANDOM kernel option.)
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
(backported from
163ab9135a9148d510cd19ca90782835e8ca80bb)
Mirko Parthey [Wed, 13 Jun 2018 14:29:50 +0000 (16:29 +0200)]
iptables: increment PKG_RELEASE to force update
While support for the FLOWOFFLOAD target is available in the firmware
images, it is still missing in some of the binary packages on
downloads.openwrt.org, e.g. for the mipsel_mips32 architecture.
Increment PKG_RELEASE to force an update of these packages.
Also adjust the package description to include the FLOWOFFLOAD target.
Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
(backported from
c84ef1f1886e0803a7b8d8a0ec18c06df4f198c2)
Kevin Darbyshire-Bryant [Mon, 18 Jun 2018 09:09:09 +0000 (09:09 +0000)]
lantiq: atm: fix ifx_atm driver integration
When upstream kernel introduced commit
c55fa3cccbc2c672e7f118be8f7484e53a8e9e77
we incorrectly updated our hack integration patch that updates atm/common.c
+++ b/net/atm/common.c
@@ -62,10 +62,16 @@ static void vcc_remove_socket(struct soc
write_unlock_irq(&vcc_sklist_lock);
}
+struct sk_buff* (*ifx_atm_alloc_tx)(struct atm_vcc *, unsigned int) = NULL;
+EXPORT_SYMBOL(ifx_atm_alloc_tx);
+
static bool vcc_tx_ready(struct atm_vcc *vcc, unsigned int size)
{
struct sock *sk = sk_atm(vcc);
+ if (ifx_atm_alloc_tx != NULL)
+ return ifx_atm_alloc_tx(vcc, size)
The correct solution is to drop our ifx_atm_alloc_tx replacement hack
entirely and let the kernel do its thing.
In reality neither pppoatm or BR2684 interfaces actually hit this code,
so the incorrect integration would only be noticed with direct socket
calls which we are unaware of a use-case.
This is not the solution to pppoatm vc-mux failing to work which started
the whole investigation, but let's fix it up anyway.
With sincerest thanks to David Woodhouse <dwmw2@infradead.org> &
Mathias Kresin <dev@kresin.me>.
Tested-on: lantiq, BT HomeHub 5a
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
(backported from
0276e1f7608a2b5252aee0c92c9834a150582ffe)
Tomasz Maciej Nowak [Sat, 9 Jun 2018 14:13:42 +0000 (16:13 +0200)]
mvebu: replace espressobin spi patch with upstream one
For easier future kernel bumps replace spi patch with upstream version
slightly modified. The modification removes partition definitions which
has been diffrent for some U-Boot versions.
Also this removes unnecessary i2c definition which was in the old patch.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
(backported from
f5bce268b0e836a7e6ae9162cc0962601364d589)
Hauke Mehrtens [Sat, 9 Jun 2018 16:40:17 +0000 (18:40 +0200)]
uboot-sunxi: update Orange Pi R1 and Zero Plus
The device tree files are now matching the kernel 4.17 and this will be
send also for integration into mainline U-Boot.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(backported from
9a26a9e8b9624d59e9d19b386d2365bb713e28b0)
Hauke Mehrtens [Sat, 9 Jun 2018 16:40:16 +0000 (18:40 +0200)]
uboot-sunxi: update to version 2018.05
This patch 220-add-sunxi50i-nanopi-neo-plus2.patch was merged upstream.
The u-boot-sunxi-with-spl.bin is now also created for the ARM64 sunxi
boards by U-Boot itself, no need to do it manually any more.
This was tested on a H2+ Orange Pi R1 and a H5 Orange Pi Zero Plus.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(backported from
f2135e7811fec7174f5a74bc579a6a8f936d1100)
Hauke Mehrtens [Sat, 9 Jun 2018 16:40:15 +0000 (18:40 +0200)]
arm-trusted-firmware-sunxi: update to version from 2018-02-10
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(backported from
7afe1caf7000f4ca671d3d681feef11af01e8551)
Linus Walleij [Fri, 15 Jun 2018 21:34:57 +0000 (23:34 +0200)]
gemini: Cook SQ201 images
This generates the "rd.gz" and "hddapp.tgz" that doesn't contain
anything of the sort but rather the OpenWRT rootfs. It works the
same way as how we generate the same layout for the NAS4220b.
For some reason the ImageInfo file is different for the SQ201.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
(backported from
1c1e2542445040b62a13862e42f961ac9c7e54f5)
Linus Walleij [Wed, 13 Jun 2018 15:47:58 +0000 (17:47 +0200)]
gemini: Add appropriate Wireless kernel modules
The D-Link DIR-685 has a RealTek RT2880 mini-PCI card in a
slot. Activate the appropriate kernel module.
The Square One SQ201 has a Ralink RT61-based mini-PCI card.
Activate the appropriate kernel modules. This fixes the
previous error just activating the firmware: the kernel
module will bring in the firmware it needs.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
(backported from
d8072a3530ea083a90044ef272de344a733dcacb)
Linus Walleij [Wed, 13 Jun 2018 15:45:04 +0000 (17:45 +0200)]
gemini: Cook a WRGG firmware image
This makes the Gemini build a WRGG-type firmware update
image for the DIR-685. This should hopefully install the
kernel from the web firmware upgrade API on the product
switching it permanently to use OpenWRT.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
(backported from
dc7f540ce180707a8f0bc3a57634964687b48dd3)
Zoltan HERPAI [Wed, 13 Jun 2018 08:51:50 +0000 (10:51 +0200)]
tools: build squashfs (v3) for ath79
Certain Netgear and AVM devices use BE squashfs for the kernel image. As
squashfs4 only supports creating LE images, add squashfs (v3) into
the tools to be built for ath79.
Trying to use an LE squashfs (thus trying to use squashfs4 only for
building the image) for the kernel image results in the bootloader
barfing and stopping.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
(backported from
3e0489dcd91faa3954a05e3fcdaf5de2d1892e67)
Daniel Golle [Fri, 15 Jun 2018 11:30:47 +0000 (13:30 +0200)]
ltq-vdsl-fw: strip legacy dsl_fw logic
We unfortunately dropped support for persistent in-flash DSL firmware.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(backported from
70f4845777cd3835f0f5b6e0294a5a53044576be)
Daniel Golle [Fri, 15 Jun 2018 11:28:38 +0000 (13:28 +0200)]
ltq-vdsl-app: use downloaded vectoring firmware
Use vectoring firmware downloaded via vdsl_fw_install.sh from
ltq-vdsl-fw package for annex B and annex J.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(backported from
c8ac28237ddc3dd5d6c78983a949e30c02b7f0b5)
Daniel Golle [Fri, 15 Jun 2018 10:21:03 +0000 (12:21 +0200)]
lantiq-vdsl-fw: update to provide recent vectoring firmware
Recent Speedport firmware downloads only work over HTTPS, so the user
either needs to provide the already downloaded file or install
ustream-ssl-* as well as ca-certificates or ca-bundle.
So to get VDSL2 with vectoring on xRX200, simply run
vdsl_fw_install.sh
on the target and either provide the downloaded file as instructed or
make sure the device is connected to the Internet and can download that
HTTPS url itself.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(backported from
0653e3127054993e908878f70fbbe1a1b784dd61)
Daniel Golle [Fri, 15 Jun 2018 09:56:05 +0000 (11:56 +0200)]
Revert "lantiq: get rid of ltq-vdsl-fw"
This reverts commit
0938233fcdef67d969f9429a10761cc640c6d56d.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(backported from
8e2f8b0c835091e0c0cabc70f219cff317f4823d)
Daniel Golle [Fri, 15 Jun 2018 06:57:44 +0000 (08:57 +0200)]
ucert: fix build
set PKG_BUILD_DIR before including package.mk to avoid problems as
seen on buildbot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(backported from
f47d7df6a89ae9457fc99dcb44c35969aa40b7a8)
Daniel Golle [Thu, 14 Jun 2018 17:39:25 +0000 (19:39 +0200)]
ucert: add package
ucert is a wrapper around usign to allow delegation and revocation of
public keys for future use in sysupgrade.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This work was sponsored by WIO (wiowireless.com)
(backported from
1b8f3d9c2ec3dd89dda524c37e4d69c3d213918e)
Daniel Golle [Thu, 14 Jun 2018 15:21:19 +0000 (17:21 +0200)]
brcm2708: move wifi calibration EEPROMs out of base-files
Ship EEPROM blobs for specific supported board only and don't have them
lurking around in our source tree but rather download them from
@github/RPi-Distro/firmware-nonfree upstream.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(backported from
037ef13a161c6167b328aaf6ca0e259a5b7db037)
Daniel Golle [Wed, 13 Jun 2018 22:42:09 +0000 (00:42 +0200)]
brcm2708: add brcmfmac-firmware-43455-sdio to DEFAULT_PACKAGES
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(backported from
a2f17214cd40c3557db34e262b28e25dcbf47edf)
Daniel Golle [Wed, 13 Jun 2018 22:37:27 +0000 (00:37 +0200)]
brcm2708: add RPi3+ wifi calibration data
Add files from
https://github.com/RPi-Distro/firmware-nonfree/raw/master/brcm/brcmfmac43455-sdio.txt
https://github.com/RPi-Distro/firmware-nonfree/raw/master/brcm/brcmfmac43455-sdio.clm_blob
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(backported from
3a40a7d5a549c85a3f0072fa03a43d2fc56547b9)
Daniel Golle [Wed, 13 Jun 2018 22:36:01 +0000 (00:36 +0200)]
linux-firmware: add firmware for BCM43455 SDIO wlan found on RPi3B+
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(backported from
2826471254f8ee955acc1f197eac443b3c34fd5b)
Felix Fietkau [Mon, 30 Apr 2018 07:24:50 +0000 (09:24 +0200)]
ramips: rename ethernet driver folder to the same one that upstream uses
Preparation for sharing offload code with the mediatek target through
generic files/
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(backported from
ec502cd3fe926f0dbc5f6020ee22929b18ef16ee)
Daniel Engberg [Sat, 9 Jun 2018 20:29:25 +0000 (22:29 +0200)]
popt: Add backup site
Add Gentoo's distfiles repo as backup site.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
(backported from
79bab45772f9f67e9c1c0bcde3268ded8a970ec1)
Hauke Mehrtens [Sun, 10 Jun 2018 20:00:02 +0000 (22:00 +0200)]
kernel/modules: fix kmod-mdio-gpio module dependencies
On some targets this module depends on kmod-of-mdio.
This is similar to the fixes done in:
dc629d9cf5a ("kernel: fix kmod-switch-rtl8366-smi dependency")
56bd23cf529 ("kernel: let kmod-rtl8366-smi conditionally depend on kmod-of-mdio")
Fixes: 32f32398af976e ("kernel/modules: add kmod-mdio-gpio module")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(backported from
83483ba787e5c972099da1e983e95f396961c7f2)
Martin Schiller [Wed, 26 Jul 2017 10:02:25 +0000 (12:02 +0200)]
kernel/modules: add kmod-switch-rtl8306 module
Add kernel module for kmod-switch-rtl8306.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
(backported from
5609bbabf194a56058afb3e3b7b91a308cb01f05)
Martin Schiller [Wed, 26 Jul 2017 09:51:05 +0000 (11:51 +0200)]
kernel/modules: add kmod-mdio-gpio module
Add kernel module package for kmod-mdio-gpio.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
(backported from
32f32398af976e38de4b656dfe4fc49b98b038ea)
Florian Eckert [Tue, 25 Jul 2017 14:38:56 +0000 (16:38 +0200)]
kernel/modules: add kmod-adcxx module
Add kernel module package for kmod-adcxx.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
(backported from
2f46f4375480838b3e9b89e4bcd5117e71aae8cc)
Martin Schiller [Wed, 2 Aug 2017 04:04:50 +0000 (06:04 +0200)]
kernel/modules: add kmod-random-tpm module
Add kernel module package for kmod-random-tpm.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
(backported from
503ac967c5fa88c37d7d3f8ed348677cee29f0f9)
Sven Eckelmann [Tue, 30 Jan 2018 08:41:45 +0000 (09:41 +0100)]
mac80211: ath10k: Allow to enable the thermal code of ath10k
Some ath10k firmware versions allow to access the chip internal a
temperature sensor and allow to reduce the amount of the time when the card
is allowed to send. The latter is required on devices which tend to
overheat.
An userspace service has to read
/sys/class/ieee80211/phy*/device/hwmon/hwmon*/temp1_input regularly and
then decide how much the device has to be throttled. This can be done by
writing to /sys/class/ieee80211/phy*/device/cooling_device/cur_state. By
default it is not throttled (0) but it can be throttled up to 100(%).
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
(backported from
4270847a2c2b8e4b890de16b51bd2e50c64077d2)
(rebased patches)
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Krystian Kozak [Sun, 27 May 2018 20:35:18 +0000 (22:35 +0200)]
sparse: updated to version 0.5.2
Updated to latest stable release
Signed-off-by: Krystian Kozak <krystian.kozak20@gmail.com>
(backported from
0e9927d157f0e98303279d1049aa02ac43a49e0b)
Rosen Penev [Thu, 7 Jun 2018 21:21:38 +0000 (14:21 -0700)]
ramips: mt7621: Fix some cosmetic DTC warnings
Node /cpus/cpu@0 has a unit name, but no reg property
Node /cpus/cpu@1 has a unit name, but no reg property
Node /cpuintc@0 has a unit name, but no reg property
Node /cpuclock@0 has a unit name, but no reg property
Node /sysclock@0 has a unit name, but no reg property
Node /pcie@
1e140000/pcie0 missing ranges for PCI bridge (or not a bridge)
Node /pcie@
1e140000/pcie0 missing bus-range for PCI bridge
Node /pcie@
1e140000/pcie1 missing ranges for PCI bridge (or not a bridge)
Node /pcie@
1e140000/pcie1 missing bus-range for PCI bridge
Node /pcie@
1e140000/pcie2 missing ranges for PCI bridge (or not a bridge)
Node /pcie@
1e140000/pcie2 missing bus-range for PCI bridge
Signed-off-by: Rosen Penev <rosenp@gmail.com>
(backported from
289b2f5e8541943c08bcd37d61093e2fd29bc80a)
Rosen Penev [Thu, 7 Jun 2018 17:36:19 +0000 (10:36 -0700)]
ramips: mmc: Add back some non-mt7621 code that staging removed
This reverts commit
8a570921b5ba49a2d3824f1220e4c53809063468.
This seems to have been accidentally reverted. This fixes mt7620 and
mt7628.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
(backported from
66cc6dd6c4b19a8ef9e5d2ebed3e10876c8aeaf0)
Kevin Darbyshire-Bryant [Thu, 7 Jun 2018 16:33:57 +0000 (16:33 +0000)]
ramips: mir3g dts define usb port Vcc volt regulator GPIO
Define USB port power on/off GPO as voltage regulator type instead of
exposing as a normal GPIO.
The GPO is now controlled by the USB driver via the voltage regulator
definition. The regulator is of fixed output type (5V for USB) hence the
GPO switches power on/off to USB pin 1 (Vcc)
USB port power is enabled on driver load and disabled on driver unload.
Enable kernel support for fixed voltage regulator types on mt7621.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
(backported from
8110bf18f4c1d04e8dfe94438caeadf78ceac892)
Christian Lamparter [Thu, 7 Jun 2018 15:36:58 +0000 (17:36 +0200)]
ipq40xx: flesh out MR33's pcie dts definitions
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(backported from
4363b5362fc48cf3d3ae9d7f5363d4efeba8bf7c)
Christian Lamparter [Thu, 7 Jun 2018 15:36:57 +0000 (17:36 +0200)]
ipq40xx: fix OpenMesh A62 dtc warnings
Warning (pci_bridge): Node /soc/pci@
40000000/pcie@0 missing ranges for PCI bridge (or not a bridge)
Warning (pci_bridge): Node /soc/pci@
40000000/pcie@0 missing bus-range for PCI bridge
Warning (pci_bridge): Node /soc/pci@
40000000/pcie@0/ath10k@0,0 node name is not "pci" or "pcie"
Warning (pci_bridge): Node /soc/pci@
40000000/pcie@0/ath10k@0,0 missing ranges for PCI bridge (or not a bridge)
Warning (pci_bridge): Node /soc/pci@
40000000/pcie@0/ath10k@0,0 incorrect #address-cells for PCI bridge
Warning (pci_bridge): Node /soc/pci@
40000000/pcie@0/ath10k@0,0 incorrect #size-cells for PCI bridge
Warning (pci_bridge): Node /soc/pci@
40000000/pcie@0/ath10k@0,0 missing bus-range for PCI bridge
Warning (unit_address_format): Failed prerequisite 'pci_bridge'
Warning (pci_device_reg): Failed prerequisite 'pci_bridge'
Warning (pci_device_bus_num): Failed prerequisite 'pci_bridge'
Cc: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Tested-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
(backported from
146fbeb81cc6eae1bba63a708b5a28071acc874e)
Christian Lamparter [Thu, 7 Jun 2018 15:36:56 +0000 (17:36 +0200)]
ipq40xx: fix dtc warning about /soc/ad-hoc-bus missing a unit name
This patch fixes a dtc warning that shows up for every device
Warning (unit_address_vs_reg): Node /soc/ad-hoc-bus has a reg or ranges property, but no unit name
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(backported from
2f1fa045878d13c565012f855fa767a10286d8c1)
Christian Lamparter [Thu, 7 Jun 2018 15:36:55 +0000 (17:36 +0200)]
ipq40xx: set #size-cells to 0 to fix warning
qcom-ipq4018-ex6100v2.dtb: Warning (reg_format): "reg" property in
/led_spi/led_gpio@0 has invalid length (4 bytes)
qcom-ipq4018-ex6100v2.dtb: Warning (avoid_default_addr_size):
Relying on default #size-cells value for /led_spi/led_gpio@0
Cc: Thomas Hebb <tommyhebb@gmail.com>
Cc: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(backported from
b22e37528beec22d8e98ebe9f2db049b218313c9)
Krystian Kozak [Sun, 27 May 2018 20:54:04 +0000 (22:54 +0200)]
imx-uuc: updated to latest git HEAD
8e29d86 linuxrc: remove superfluous shebang line
12d2045 gitignore: remove Windows stuff
57d8969 Add travis hint
8edf4cc sdimage: use fsync before closing the device (fixes #1)
d395b31 uuc: fix some compiler warnings
Signed-off-by: Krystian Kozak <krystian.kozak20@gmail.com>
(backported from
c844d6a8e43a5b76f4aba0a7ab59fe8286482044)
Lucian Cristian [Sun, 3 Jun 2018 23:09:15 +0000 (02:09 +0300)]
ath79: fix qca956x SoC boot
based on old ar71xx irq.c driver
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
(backported from
a0a616e1b8d8f3a0cfe1b91b29eef5a8326769f7)