Shiji Yang [Thu, 22 Feb 2024 01:56:36 +0000 (09:56 +0800)]
firmware: add firmware package for Realtek RTL8188FU
Realtek RTL8188F is an 802.11n 1x1 USB Wi-Fi adapter. It has been
supported by the upstream rtl8xxxu driver since Linux 6.2 kernel.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Sebastian Schaper [Sun, 11 Feb 2024 17:55:43 +0000 (18:55 +0100)]
ath79: add support for D-Link COVR-C1200 A1
The COVR-C1200 devices are sold as "Whole Home Mesh Wi-Fi"
sets in packs of two (COVR-C1202) and three (COVR-C1203).
Specifications:
* QCA9563, 16 MiB flash, 128 MiB RAM, 2x3:2 802.11n
* QCA9886 2x2:2 801.11ac Wave 2
* AR8337, 2 Gigabit ports (1: WAN; 2: LAN)
* USB Type-C power connector (5V, 3A)
Installation COVR Point A:
* In factory reset state: OEM Web UI is at 192.168.0.50
no DHCP, skip wizard by directly accessing:
http://192.168.0.50/UpdateFirmware_Simple.html
* After completing setup wizard: Web UI is at 192.168.0.1
DHCP enabled, login with empty password
* Flash factory.bin
* Perform a factory reset to restore OpenWrt UCI defaults
Installation COVR Points B:
* OEM Web UI is at 192.168.0.50, no DHCP, empty password
* Flash factory.bin
* Perform a factory reset to restore OpenWrt UCI defaults
Recovery:
* Keep reset button pressed during power on
* Recovery Web UI is at 192.168.0.50, no DHCP
* Flash factory.bin
used to work best with Chromium-based browsers or curl:
curl -F firmware=@factory.bin \
http://192.168.0.50/upgrade.cgi
since this fails to work on modern Linux systems,
there is also a script dlink_recovery_upload.py
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Sebastian Schaper [Sun, 11 Feb 2024 17:53:07 +0000 (18:53 +0100)]
ath79: split dtsi for D-Link COVR-P2500
in preparation of adding COVR-C1200
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Christian Lamparter [Fri, 8 Mar 2024 20:16:44 +0000 (21:16 +0100)]
firmware: intel-microcode: update to
20231114
Debian changelog:
intel-microcode (3.
20231114.1) unstable; urgency=medium
* New upstream microcode datafile
20231114 (closes: #
1055962)
Mitigations for "reptar", INTEL-SA-00950 (CVE-2023-23583)
Sequence of processor instructions leads to unexpected behavior for some
Intel(R) Processors, may allow an authenticated user to potentially enable
escalation of privilege and/or information disclosure and/or denial of
service via local access.
Note: "retvar" on 4th gen Xeon Scalable (sig 0x806f8 pfm 0x87), 12th gen
Core mobile (sig 0x906a4 pfm 0x80), 13th gen Core desktop (sig 0xb0671 pfm
0x01) were already mitigated by a previous microcode update.
* Fixes for unspecified functional issues
* Updated microcodes:
sig 0x000606a6, pf_mask 0x87, 2023-09-01, rev 0xd0003b9, size 299008
sig 0x000606c1, pf_mask 0x10, 2023-09-08, rev 0x1000268, size 290816
sig 0x000706e5, pf_mask 0x80, 2023-09-03, rev 0x00c2, size 113664
sig 0x000806c1, pf_mask 0x80, 2023-09-07, rev 0x00b4, size 111616
sig 0x000806c2, pf_mask 0xc2, 2023-09-07, rev 0x0034, size 98304
sig 0x000806d1, pf_mask 0xc2, 2023-09-07, rev 0x004e, size 104448
sig 0x000806f8, pf_mask 0x87, 2023-06-16, rev 0x2b0004d0, size 572416
sig 0x000806f8, pf_mask 0x87, 2023-06-16, rev 0x2b0004d0
sig 0x000806f7, pf_mask 0x87, 2023-06-16, rev 0x2b0004d0
sig 0x000806f6, pf_mask 0x87, 2023-06-16, rev 0x2b0004d0
sig 0x000806f5, pf_mask 0x87, 2023-06-16, rev 0x2b0004d0
sig 0x000806f4, pf_mask 0x87, 2023-06-16, rev 0x2b0004d0
sig 0x000806f8, pf_mask 0x10, 2023-06-26, rev 0x2c000290, size 605184
sig 0x000806f8, pf_mask 0x10, 2023-06-26, rev 0x2c000290
sig 0x000806f6, pf_mask 0x10, 2023-06-26, rev 0x2c000290
sig 0x000806f5, pf_mask 0x10, 2023-06-26, rev 0x2c000290
sig 0x000806f4, pf_mask 0x10, 2023-06-26, rev 0x2c000290
sig 0x00090672, pf_mask 0x07, 2023-06-07, rev 0x0032, size 222208
sig 0x00090672, pf_mask 0x07, 2023-06-07, rev 0x0032
sig 0x00090675, pf_mask 0x07, 2023-06-07, rev 0x0032
sig 0x000b06f2, pf_mask 0x07, 2023-06-07, rev 0x0032
sig 0x000b06f5, pf_mask 0x07, 2023-06-07, rev 0x0032
sig 0x000906a3, pf_mask 0x80, 2023-06-07, rev 0x0430, size 220160
sig 0x000906a3, pf_mask 0x80, 2023-06-07, rev 0x0430
sig 0x000906a4, pf_mask 0x80, 2023-06-07, rev 0x0430
sig 0x000906a4, pf_mask 0x40, 2023-05-05, rev 0x0005, size 117760
sig 0x000a0671, pf_mask 0x02, 2023-09-03, rev 0x005d, size 104448
sig 0x000b0671, pf_mask 0x32, 2023-08-29, rev 0x011d, size 210944
sig 0x000b06a2, pf_mask 0xe0, 2023-08-30, rev 0x411c, size 216064
sig 0x000b06a2, pf_mask 0xe0, 2023-08-30, rev 0x411c
sig 0x000b06a3, pf_mask 0xe0, 2023-08-30, rev 0x411c
sig 0x000b06e0, pf_mask 0x11, 2023-06-26, rev 0x0012, size 136192
* Updated 2023-08-08 changelog entry:
Mitigations for "retvar" on a few processors, refer to the 2023-11-14
entry for details. This information was disclosed in 2023-11-14.
* source: update symlinks to reflect id of the latest release,
20231114
-- Henrique de Moraes Holschuh <hmh@debian.org> Thu, 16 Nov 2023 08:09:43 -0300
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Christian Lamparter [Fri, 8 Mar 2024 20:12:45 +0000 (21:12 +0100)]
Revert "ipq-wifi: fix upstream board-2.bin ZTE M289F snafu"
This reverts commit
75505c5ec724b9b961dcb411bac1d4b9aede3e1d.
The issue has been fixed upstream.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Daniel Golle [Sat, 9 Mar 2024 13:50:40 +0000 (13:50 +0000)]
mediatek: linksys-e8450: improve compat warning
Include a statement about having to run the installer in the
sysupgrade compat warning for the Linksys E8450 (UBI).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sat, 9 Mar 2024 13:48:03 +0000 (13:48 +0000)]
mediatek: wait for fitblk rootfs
Probing of the fitblk driver in some situations happens after the kernel
attempts to mount rootfs, which then fails.
Always use 'rootwait' when using fitblk for rootfs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sat, 9 Mar 2024 13:58:29 +0000 (13:58 +0000)]
uboot-mediatek: add 'rootwait' to bootargs where needed
Probing of the fitblk driver in some situations happens after Linux
attempts to mount rootfs, which then fails.
Always use 'rootwait' kernel parameter when using fitblk for rootfs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Felix Fietkau [Fri, 8 Mar 2024 21:42:50 +0000 (22:42 +0100)]
mac80211: fix a regression in the broadcast AQL patch
The AQL limit for buffered broadcast packets is higher than the maximum
total pending airtime limit. This can get unicast data stuck whenever there
is too much pending broadcast data. Fix this by excluding broadcast AQL from
the total limit.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Tue, 5 Mar 2024 18:13:52 +0000 (19:13 +0100)]
mbedtls: enable threading support
Fixes libssh, which requires it. Bump ABI_VERSION, since enabling this
option affects data structures in mbedtls include files.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
INAGAKI Hiroshi [Mon, 4 Mar 2024 10:12:07 +0000 (19:12 +0900)]
ath79: cleanup and enable uart1 on ELECOM WAB-I1750-PS
Cleanup uart1-related node on ELECOM WAB-I1750-PS and enable it for
"SERIAL" port on the case.
"SERIAL" port can be used for OpenWrt console by adding the following
line to /etc/inittab and rebooting:
ttyATH1::askfirst:/usr/libexec/login.sh
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
INAGAKI Hiroshi [Mon, 4 Mar 2024 10:11:36 +0000 (19:11 +0900)]
ath79: drop unnecessary &uart node from dtsi of QCA955x devices
&uart (uart0) is already enabled in qca955x.dtsi by default.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
INAGAKI Hiroshi [Mon, 4 Mar 2024 11:28:23 +0000 (20:28 +0900)]
ath79: add aliases to qca955x.dtsi for uart0/1
Add aliases with "serialN = &uartN;" of uart0/1 on QCA955x SoCs to
qca955x.dtsi, to enable uart1 on Linux Kernel.
without this:
[ 0.342915] ar933x-uart
18500000.uart: unable to get alias id, err=-19
Additionally, remove "serial0 = &uart;" alias from QCA955x device
dts/dtsi files.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
INAGAKI Hiroshi [Mon, 4 Mar 2024 10:08:07 +0000 (19:08 +0900)]
ath79: add HighSpeed UART (uart1) support for QCA955x
Add HighSpeed UART support to QCA955x series SoCs as a secondary UART
(uart1). This UART is compatible with qca,ar9330-uart.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
INAGAKI Hiroshi [Mon, 4 Mar 2024 10:07:05 +0000 (19:07 +0900)]
ath79: rename label of primary UART on QCA955x to "uart0"
Rename the DT label of the primary UART on Qualcomm Atheros QCA955x
series SoCs to "uart0" from "uart" for the preparation to add HighSpeed
UART (uart1) support.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Christian Lamparter [Thu, 7 Mar 2024 21:43:41 +0000 (22:43 +0100)]
mpc85xx: p1020: convert Aerohive AP330/AP350 to simpleImage
with 6.1, the kernel no longer fitted into the 16 MiB and
kicking down the can and increasing KERNEL_SIZE to 20 MiB
didn't help as the device failed to boot.
Using 'kernel-bin | gzip | uimage gzip' didn't work since the
uboot does not have enough heap to decompress these big kernels.
And finally playing around with uboot was more a hassle than
converting this device to take the simpleImage-boot-route in
the future.
Note: The device now takes even longer on the first boot-up after
the flash due to JFFS2 initializing all the remaining flash.
Be prepared to wait up to 10 minutes before the green status LED
stops blinking and will shine a solid green!
(On the plus site: the device now has ~10 MiB of additional
space for rootfs+rootfs_data).
Note2: This patch includes a kernel patch refresh.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Pawel Dembicki [Tue, 21 Nov 2023 09:50:23 +0000 (10:50 +0100)]
mpc85xx: add 6.1 testing kernel
Configure 6.1 testing kernel for mpc85xx target.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Pawel Dembicki [Mon, 19 Feb 2024 12:39:10 +0000 (13:39 +0100)]
mpc85xx: p1010: change wrapper address of simple image devices
Kernel and initramfs size grows. Now uncompressed initramfs image and
regular kernel image overlaps configured area:
Initramfs:
WRAP arch/powerpc/boot/simpleImage.br200-wp
INFO: Uncompressed kernel (size 0x1428688) overlaps the address of the
wrapper(0x1000000)
INFO: Fixing the link_address of wrapper to (0x1500000)
WRAP arch/powerpc/boot/simpleImage.tl-wdr4900-v1
INFO: Uncompressed kernel (size 0x1428688) overlaps the address of the
wrapper(0x1000000)
INFO: Fixing the link_address of wrapper to (0x1500000)
WRAP arch/powerpc/boot/simpleImage.ws-ap3715i
INFO: Uncompressed kernel (size 0x1428688) overlaps the address of the
wrapper(0x1000000)
INFO: Fixing the link_address of wrapper to (0x1500000)
Regular image:
WRAP arch/powerpc/boot/simpleImage.br200-wp
INFO: Uncompressed kernel (size 0x10e0688) overlaps the address of the
wrapper(0x1000000)
INFO: Fixing the link_address of wrapper to (0x1100000)
WRAP arch/powerpc/boot/simpleImage.tl-wdr4900-v1
INFO: Uncompressed kernel (size 0x10e0688) overlaps the address of the
wrapper(0x1000000)
INFO: Fixing the link_address of wrapper to (0x1100000)
WRAP arch/powerpc/boot/simpleImage.ws-ap3715i
INFO: Uncompressed kernel (size 0x10e0688) overlaps the address of the
wrapper(0x1000000)
INFO: Fixing the link_address of wrapper to (0x1100000)
Let's change wrapper address to safe value.
Tested on: TL-WDR4900, BR200-WP
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Pawel Dembicki [Tue, 21 Nov 2023 09:45:22 +0000 (10:45 +0100)]
mpc85xx: kernel: refresh 6.1 config
Kernel config needs to be refreshed after copy from 5.15.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Pawel Dembicki [Tue, 21 Nov 2023 09:43:46 +0000 (10:43 +0100)]
mpc85xx: refresh 6.1 patches
Most changes done by "make target/linux/refresh"
Manually refreshed:
102-powerpc-add-cmdline-override.patch
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Pawel Dembicki [Tue, 21 Nov 2023 08:38:37 +0000 (09:38 +0100)]
mpc85xx: copy patches 5.15 to 6.1
Just copy of config.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Pawel Dembicki [Tue, 21 Nov 2023 08:38:20 +0000 (09:38 +0100)]
mpc85xx: copy config 5.15 to 6.1
Simple copy of patches.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Pawel Dembicki [Tue, 21 Nov 2023 09:46:13 +0000 (10:46 +0100)]
mpc85xx: Get rid of 'of_flat_dt_is_compatible'
This patch replaces 'of_flat_dt_is_compatible' with 'of_machine_is_compatible'.
The TL-WDR4900 platform file won't compile in the 6.1 kernel. The platform
files for the rest of the routers have been reworked or based on newer
solutions.
Let's make the TL-WDR4900 consistent with them.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Robert Marko [Wed, 6 Mar 2024 21:21:47 +0000 (22:21 +0100)]
kernel: crypto: use ARM64 SHA256 CE optimized module for more targets
At start I only set qualcommax to use the Crypto Extensions optimized
version of SHA256 as I knew it supports the optional Crypto Extensions.
However, after looking into the tree there are more targets/subtargets
that I could find at least a specification sheet that says the support
Cryptographic Extensions, so lets add them.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Robert Marko [Wed, 6 Mar 2024 21:19:54 +0000 (22:19 +0100)]
kernel: crypto: use ARM64 SHA1 CE optimized module for more targets
At start I only set qualcommax to use the Crypto Extensions optimized
version of SHA1 as I knew it supports the optional Crypto Extensions.
However, after looking into the tree there are more targets/subtargets
that I could find at least a specification sheet that says the support
Cryptographic Extensions, so lets add them.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Hauke Mehrtens [Fri, 8 Mar 2024 13:43:08 +0000 (14:43 +0100)]
lantiq: Fix build after kernel 5.15.150
This fixes the following compile problem:
````
CC arch/mips/kernel/vpe-mt.o
arch/mips/kernel/vpe-mt.c: In function 'vpe_run':
arch/mips/kernel/vpe-mt.c:32:23: error: unused variable 'physical_memsize' [-Werror=unused-variable]
32 | unsigned long physical_memsize = 0L;
| ^~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
make[6]: *** [scripts/Makefile.build:289: arch/mips/kernel/vpe-mt.o] Error 1
````
physical_memsize was removed from upstream kernel, see:
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-5.15.y&id=
5b4f6c5ff65c8551018ccea40c569afd759734c0
Fixes: 387fde0da0e8 ("kernel: bump 5.15 to 5.15.150")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Christian Marangi [Fri, 8 Mar 2024 13:25:54 +0000 (14:25 +0100)]
libiwinfo: update to Git HEAD (2024-03-08)
163a640fef30 devices: add device id for Qualcomm Atheros QCA6174
8ffb8bfd1115 devices: add add Qualcomm Atheros IPQ6018 WiSoC compatible
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Furong Xu [Fri, 8 Mar 2024 08:43:00 +0000 (16:43 +0800)]
mediatek: clean duplicated #include in Xiaomi Redmi AX6000's dts
Clean duplication of #include <dt-bindings/leds/common.h>.
Thanks musashino205
Fixes: 1493e8f8cbe2 ("mediatek: convert LED color/function format for Xiaomi Redmi AX6000")
Signed-off-by: Furong Xu <xfr@outlook.com>
Qingfang Deng [Fri, 8 Mar 2024 03:07:49 +0000 (11:07 +0800)]
kernel: enable KASAN option for more architectures
KASAN has supported more architectures, such as ARM, PPC32 and RISC-V 64.
Enable KASAN option for those architectures.
Signed-off-by: Qingfang Deng <dqfext@gmail.com>
Sergey Ponomarev [Sat, 2 Mar 2024 21:50:58 +0000 (23:50 +0200)]
ubox: make logread as an alternative
The logread can be replaced with syslog-ng.
To support this it should be an alternative itself.
Signed-off-by: Sergey Ponomarev <stokito@gmail.com>
Furong Xu [Thu, 7 Mar 2024 02:56:18 +0000 (10:56 +0800)]
mediatek: filogic: switch to fitblk for Xiaomi Redmi AX6000
Use the new fitblk driver.
Run-tested: filogic/mt7986a-xiaomi-redmi-router-ax6000-ubootmod
Signed-off-by: Furong Xu <xfr@outlook.com>
Furong Xu [Mon, 4 Mar 2024 12:54:44 +0000 (20:54 +0800)]
mediatek: convert LED color/function format for Xiaomi Redmi AX6000
Commit
2d63d42f5e2f ("mediatek: convert to new LED color/function
format where possible") leaves Xiaomi Redmi AX6000 un-converted,
the two LEDs become dead.
Now, LEDs are alive again.
Fixes: 2d63d42f5e2f ("mediatek: convert to new LED color/function
format where possible")
Signed-off-by: Furong Xu <xfr@outlook.com>
Tony Ambardar [Thu, 7 Mar 2024 09:21:40 +0000 (01:21 -0800)]
kernel: 6.1: add missing config symbol for tracing
Add missing option CONFIG_FPROBE to generic config, found building x86_64
arch with tracing enabled.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Hauke Mehrtens [Thu, 22 Feb 2024 20:33:45 +0000 (21:33 +0100)]
linux-firmware: Update to version
20240220
This updates the following firmware files:
airoha-en8811h-firmware/lib/firmware/airoha/EthMD32.DSP.bin
airoha-en8811h-firmware/lib/firmware/airoha/EthMD32.dm.bin
amdgpu-firmware (Many files)
ar3k-firmware/lib/firmware/qca/hpnv21.bin
ar3k-firmware/lib/firmware/qca/hpnv21g.bin
ath10k-board-qca4019/lib/firmware/ath10k/QCA4019/hw1.0/board-2.bin
ath10k-board-qca9888/lib/firmware/ath10k/QCA9888/hw2.0/board-2.bin
ath10k-firmware-qca6174/lib/firmware/ath10k/QCA6174/hw3.0/firmware-6.bin
ath11k-firmware-wcn6750/lib/firmware/ath11k/WCN6750/hw1.0/board-2.bin
ath11k-firmware-wcn6855/lib/firmware/ath11k/WCN6855/hw2.0/amss.bin
ath11k-firmware-wcn6855/lib/firmware/ath11k/WCN6855/hw2.0/board-2.bin
ath11k-firmware-wcn6855/lib/firmware/ath11k/WCN6855/hw2.1/amss.bin
ath11k-firmware-wcn6855/lib/firmware/ath11k/WCN6855/hw2.1/board-2.bin
ibt-firmware/lib/firmware/intel/ibt-0040-0041.ddc
ibt-firmware/lib/firmware/intel/ibt-0040-0041.sfi
ibt-firmware/lib/firmware/intel/ibt-0040-1050.sfi
ibt-firmware/lib/firmware/intel/ibt-0040-4150.sfi
ibt-firmware/lib/firmware/intel/ibt-0041-0041.sfi
ibt-firmware/lib/firmware/intel/ibt-0180-0041.sfi
ibt-firmware/lib/firmware/intel/ibt-0180-1050.sfi
ibt-firmware/lib/firmware/intel/ibt-0180-4150.sfi
ibt-firmware/lib/firmware/intel/ibt-1040-0041.sfi
ibt-firmware/lib/firmware/intel/ibt-1040-4150.sfi
iwlwifi-firmware-be200/lib/firmware/iwlwifi-gl-c0-fm-c0-83.ucode
iwlwifi-firmware-be200/lib/firmware/iwlwifi-gl-c0-fm-c0.pnvm
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sun, 3 Mar 2024 11:34:19 +0000 (12:34 +0100)]
kernel: Remove unused schedulers
These schedulers were removed in kernel 5.15.150 and 6.1.180.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sun, 3 Mar 2024 11:25:27 +0000 (12:25 +0100)]
kernel: bump 5.15 to 5.15.150
Removed because it is upstream:
bcm53xx/patches-5.15/030-v5.16-0019-ARM-dts-BCM53573-Describe-on-SoC-BCM53125-rev-4-swit.patch
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=
cb1003c07e746e4e82bdd3959c9ea37018ed41a3
Removed because it is upstream:
bcm53xx/patches-5.15/037-v6.6-0004-ARM-dts-BCM53573-Drop-nonexistent-default-off-LED-tr.patch
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=
c65a23e98e38dc991f495d6bdb3cfa6163a88a0c
Removed because it is upstream:
bcm53xx/patches-5.15/037-v6.6-0005-ARM-dts-BCM53573-Drop-nonexistent-usb-cells.patch
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=
71475bcee001cae3844644c2787eef93b26489d1
Adapted hack-5.15/650-netfilter-add-xt_FLOWOFFLOAD-target.patch to match
the changes from the upstream flow offload patch:
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=
7c71b831220edeab7ce603d818dc1708d9ea4137
Manually Adapted the following patch:
bcm53xx/patches-5.15/035-v6.2-0004-ARM-dts-broadcom-align-LED-node-names-with-dtschema.patch
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 2 Mar 2024 18:14:22 +0000 (19:14 +0100)]
kernel: bump 5.15 to 5.15.149
Removed because it is upstream:
generic/pending-5.15/540-ksmbd-only-v2-leases-handle-the-directory.patch
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=
81ea755b8fa57ce186f56f14b709cf491c2a5505
Manually Adapted the following patch:
ath79/patches-5.15/900-unaligned_access_hacks.patch
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Robert Marko [Tue, 5 Mar 2024 09:31:48 +0000 (10:31 +0100)]
ath25: drop target
ath25 has been on life support for the last couple of releases, eventually
leading to marking it as source-only in 2023.
It has been basically only touched to do a kernel bump so that we can make
the new OpenWrt release which was a challenge due to small RAM amount.
However, with the attempt of kernel 6.1 update it turns out that kernel
cannot even finish booting due to RAM constraints, so its time to let this
target go.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Sven Eckelmann [Thu, 7 Mar 2024 08:24:20 +0000 (09:24 +0100)]
ath11k-firmware: Move from kvalo to new upstream repository
It was announced [1] that the original staging repositories are no longer
used for staging of new firmware binaries. And that the old repository will
be removed [2] in June 2024.
The ath11k-firmware package must therefore point to the new repository
before the old one is no longer accessible.
[1] https://lore.kernel.org/r/
bac97f31-4a70-4c4c-8179-
4ede0b32f869@quicinc.com
[2] https://github.com/kvalo/ath11k-firmware/commit/
8d2cc160f390badd62970a66483214773c3fbea1
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Robert Marko [Wed, 6 Mar 2024 20:54:07 +0000 (21:54 +0100)]
kernel: crypto: add SHA512 ARM64 ASM optimized module
Kernel has an ASM optimized version of SHA512 that was ported from
OpenSSL, so lets package it as it provides significant perfomance
improvement compared to the generic implementation.
There is a Cryptographic Extension based version as well, but that relies
on ARMv8.2 ISA which I am not aware any of the OpenWrt supported SoC-s use.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Robert Marko [Wed, 6 Mar 2024 17:38:28 +0000 (18:38 +0100)]
kernel: crypto: add SHA2(224 and 256) ARM64 CE optimized module
Kernel has optimized version of SHA2(224 and 256) using the ARMv8 Crypto
Extensions, so lets package it.
Use it by default for qualcommax as it uses Cortex-A53 core and has ARMv8
CE extensions present.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Robert Marko [Wed, 6 Mar 2024 17:30:21 +0000 (18:30 +0100)]
kernel: crypto: add SHA256 ARM64 ASM optimized module
Kernel has an ASM optimized version of SHA256 that was ported from
OpenSSL, so lets package it as it provides significant perfomance
improvement compared to the generic implementation.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Robert Marko [Wed, 6 Mar 2024 10:47:45 +0000 (11:47 +0100)]
kernel: crypto: add SHA1 ARM64 CE optimized module
Kernel has optimized version of SHA1 using the ARMv8 Crypto Extensions,
so lets package it.
Use it by default for qualcommax as it uses Cortex-A53 core and has ARMv8
CE extensions present.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Weijie Gao [Sun, 7 Jan 2024 05:42:00 +0000 (13:42 +0800)]
cryptodev-linux: update to 1.13
Update to 1.13 with upstream backports.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Robert Marko [Thu, 29 Feb 2024 21:18:20 +0000 (22:18 +0100)]
kernel: qca-ssdk: refresh PCS patch
Recently added PCS patch requires a refresh, so lets do it.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Robert Marko [Tue, 5 Mar 2024 19:15:55 +0000 (20:15 +0100)]
kernel: crypto: package SHA3
SHA3 is now required by jitterentropy_rng in kernel 6.6, so lets start
preparing by packaging SHA3 support as its supported in 5.15 and 6.1
kernels as well.
AFAIK, only ARMv8.2 has a crypto extension for SHA3, however I am not aware
of any SoC we support that uses ARMv8.2 ISA so its not enabled currently.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Rafał Miłecki [Mon, 4 Mar 2024 14:18:13 +0000 (15:18 +0100)]
base-files: sysupgrade: handle errors when generating backup
1. Return error if any step of generating tar file fails
2. Use pipefail to avoid calling "gzip" if tar failed
Fixes: e36cc530927c ("base-files: sysupgrade: use tar helper to include installed_packages.txt")
Reported-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Cc: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Cc: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Dirk Buchwalder [Sun, 3 Mar 2024 15:00:46 +0000 (16:00 +0100)]
qualcommax: ipq60xx: add support for netgear wax214
Netgear WAX214 is a 802.11 ax dual-band AP
with PoE. (similar to Engenius EWS357APV3)
Specifications:
• CPU: Qualcomm IPQ6010 Quad core Cortex-A53
• RAM: 512MB of DDR3
• Storage: 128MB NAND (Macronix MX30UF1G18AC)
• Ethernet: 1x 1G RJ45 port (QCA8072) PoE
• WIFI:
2.4GHz: Qualcomm QCN5022 2x2 802.11b/g/n/ax 574 Mbps PHY rate
5GHz: Qualcomm QCN5052 2x2 802.11a/b/g/n/ac/ax 1201 PHY rate
• LEDs:
4 x GPIO-controlled LEDs
- 1 Power LED (orange)
- 1 LAN LED (blue)
- 1 WIFI 5g LED (blue)
- 1 WIFI 2g LED (blue)
black_small_square Buttons: 1x soft reset
black_small_square Power: 12V DC jack or PoE (802.3af )
An populated serial header is onboard, format is
1.25mm 4p (DF13A-4P-1.25H)
RX/TX is working, bootwait is active, secure boot is not
enabled.
The root password of the stock firmware is unknown,
but failsafe mode can be entered to reset the password.
Installation Instructions:
- obtain serial access
- stop auto boot (press "4", Entr boot command line
interface)
- setenv active_fw 0 (to boot from the primary rootfs,
or set to 1 to boot from the secondary rootfs
partition)
- saveenv
- tftpboot the initramfs image
- bootm
- copy
openwrt-qualcommax-ipq60xx-netgear_wax214-squashfs-factory.ubi
to the device
- write the image to the NAND:
- cat /proc/mtd and look for rootfs partition (should
be mtd11,
or mtd12 if you choose active_fw 1)
- ubiformat /dev/mtd11 -f -y
openwrt-qualcommax-ipq60xx-netgear_wax214-squashfs-factory.ubi
- reboot
Note: the firmware is senao-based. But I was unable to build
a valid senao-header into the image.
Maybe they changed the header format and senaoFW isn't
working any more.
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
Dirk Buchwalder [Mon, 4 Mar 2024 20:33:32 +0000 (21:33 +0100)]
ipq-wifi: update to version 2024-03-04
The new version adds support for the Netgear WAX214.
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
John Audia [Fri, 1 Mar 2024 21:08:40 +0000 (16:08 -0500)]
kernel: bump 6.1 to 6.1.80
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.80
Manually rebased:
generic/hack-6.1/650-netfilter-add-xt_FLOWOFFLOAD-target.patch[1]
All other patches automatically rebased.
1. Acknowledgement to @heheb and @DragonBluep. Upstream commit for ref: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.80&id=
9c5662e95a8dcc232c3ef4deb21033badcd260f6
Build system: x86/64
Build-tested: x86/64/AMD Cezanne, ramips/tplink_archer-a6-v3
Run-tested: x86/64/AMD Cezanne, ramips/tplink_archer-a6-v3
Signed-off-by: John Audia <therealgraysky@proton.me>
John Audia [Sun, 3 Mar 2024 14:49:03 +0000 (09:49 -0500)]
kernel: Remove dsmark support
dsmark support was removed in kernel 5.15.150 and 6.1.80. Remove it from
the kmod package as well
Signed-off-by: John Audia <therealgraysky@proton.me>
Matthias Schiffer [Mon, 4 Mar 2024 22:45:15 +0000 (23:45 +0100)]
build: do not depend on $(STAGING_DIR)/.prepared when in SDK
The dependency can't be satisfied when building using the SDK, breaking
package builds. As the staging and bin dirs are distributed with the SDK
archive, ignoring the dependency is fine when SDK is set.
Fixes: fbb924abff8a ("build: add $(STAGING_DIR) and $(BIN_DIR) ...")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Álvaro Fernández Rojas [Tue, 30 Jan 2024 20:30:20 +0000 (21:30 +0100)]
bcm27xx: use PARTUUID for root in cmdline
This allows booting from USB/NVME while keeping SD compatibility.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Álvaro Fernández Rojas [Wed, 31 Jan 2024 10:43:55 +0000 (11:43 +0100)]
base-files: sysupgrade: allow overriding config restore
Some platforms like Raspberry Pi require patching some backup files like
cmdline.txt in order to set the correct root PARTUUID.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Álvaro Fernández Rojas [Tue, 30 Jan 2024 20:28:54 +0000 (21:28 +0100)]
bcm27xx: pass signature to partition generation
Passes IMG_PART_SIGNATURE to ptgen instead of using the default "OWRT"
signature.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Álvaro Fernández Rojas [Mon, 4 Mar 2024 15:20:55 +0000 (16:20 +0100)]
bcm27xx: base-files: fix platform_copy_config
/boot/kernel*.img wildcard only works without quotation marks.
Fixes: 1a5e51ab0011 ("bcm27xx: base-files: fix platform_copy_config")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Álvaro Fernández Rojas [Mon, 5 Feb 2024 17:39:57 +0000 (18:39 +0100)]
bcm63xx: drop target
BCM63xx maintainance is a PITA since there's no full Device Tree support and
therefore every board needs it's own definition in board_bcm963xx.c
There's no DSA support for this board and there have been very few
contributions in the last years.
Moreover, BCM63xx SoCs >= BCM6358 are already supported in bmips target, so
any efforts to keep this target alive aren't worth the time.
Let's focus the community efforts on improving bmips instead.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Jo-Philipp Wich [Mon, 4 Mar 2024 13:50:46 +0000 (14:50 +0100)]
base-files: sysupgrade: fix streaming backup archives to stdout
Due to previous refactoring in sysupgrade, writing backup archives to
stdout became impossible since the hardcoded gzip output redirection
did not account for the `-` special case filename.
Fix this issue by substituting `-` with `/proc/self/fd/1` in the tar
archive output path variable.
Also remove a redundant `rm -f` of the target file path that occurs
before the file could've possibly been written.
Fixes: #14773
Fixes: https://github.com/openwrt/luci/issues/6961
Fixes: e36cc53092 ("base-files: sysupgrade: use tar helper to include installed_packages.txt")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Matthias Schiffer [Thu, 1 Feb 2024 23:46:58 +0000 (00:46 +0100)]
build: add $(STAGING_DIR) and $(BIN_DIR) preparation to target and package subdir compile dependencies
In a pristine build, these directories are created as dependencies of
the tools subdir compile, however this step never runs when the tools
compile stamp already exists. Since commit
ed6ba2801c0a ("tools: keep
stamp file in $(STAGING_DIR_HOST)"), this will happen after `make clean`:
$(STAGING_DIR) has been deleted, but the tools stamp still exists, so
the next build will fail because $(STAGING_DIR) has not been set up
correctly.
Fix builds after `make clean` by adding the preparation as dependencies
for the target and package directories as well.
Fixes: ed6ba2801c0a ("tools: keep stamp file in $(STAGING_DIR_HOST)")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Daniel Golle [Sun, 3 Mar 2024 15:22:54 +0000 (15:22 +0000)]
kernel: lantiq: ltq-vmmc: introduce user group for vmmc
asterisk-chan-lantiq is by now the only user of the VMMC interface.
And asterisk runs as user 'asterisk' which doesn't give it permission
to open the /dev/vmmc* devices.
Introduce a new user group 'vmmc' and give permission to access the
/dev/vmmc* devices to that group.
Another commit for asterisk-chan-lantiq will add the 'asterisk' user
to that group.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Tobias Schramm [Mon, 26 Feb 2024 11:47:29 +0000 (12:47 +0100)]
mvebu: add support for SolidRun ClearFog Pro
The SolidRun ClearFog Pro is a router based on the SolidRun CN9130 SOM.
Specs:
- SoC: Quad-Core Cortex-A72 CN9130 SoC
- RAM: 4GiB DDR4
- Serial: Micro-USB port on front (FT232R, 115200 8n1)
- Storage: 8GiB eMMC, microSD card slot, 8MiB SPI NOR flash
- Ethernet: 7x GbE (1 port dedicated on SoC, 6 port switch with single GbE CPU port)
- SFP: 1x SFP+
- USB: 1x USB-A 3.1 Gen 1
- PCIe: 2x mini PCIe (one slot with USB and SIM card socket)
- SATA: 1x M.2 Key-B
In addition to the usual connectivity options this device also features
an internal mikroBUS expansion connector.
SATA is currently untested due to lack of a suitable M.2 SSD.
Installation
============
1. Write sdcard sysupgrade image to microSD card using dd or similar
2. Insert microSD card into router and apply power
3. Device boots into OpenWRT
4. (optional) dd sysupgrade image to /dev/mmcblk0 to install to eMMC
Signed-off-by: Tobias Schramm <tobias@t-sys.eu>
Tobias Schramm [Mon, 26 Feb 2024 09:40:50 +0000 (10:40 +0100)]
kernel: 6.1: backport Marvell Armada 8k AP807 cpufreq support
Upstream a patch adding support for cpufreq on AP807-based SoC like the
CN913x was submitted. Include it in patches to ensure best performance
under load and lowest power consumption in idle.
Signed-off-by: Tobias Schramm <tobias@t-sys.eu>
Tianling Shen [Sun, 25 Feb 2024 12:33:08 +0000 (20:33 +0800)]
u-boot.mk: override default PATH to avoid pick hostpkg python
hostpkg python from packages feed can be picked when do a incremental
build because hostpkg has higher priority in PATH. It may lead build
faliure as it's heavily trimmed (e.g. lacks necessary modules).
For uboot which uses binman and intree dtc, this is forced as hostpkg
python will never provide those modules by default.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Paul Geraedts [Sat, 24 Feb 2024 08:01:01 +0000 (09:01 +0100)]
mediatek: filogic: fix failsafe mode on devices with no lan1
Default to lan4 port, instead of (missing) lan1 port,
to fix failsafe mode on Xiaomi AX3000T, WR30U, AX6000
Build system: x86/64
Build-tested: mediatek/filogic/xiaomi_mi-router-ax3000t-ubootmod
Run-tested: mediatek/filogic/xiaomi_mi-router-ax3000t-ubootmod
Signed-off-by: Paul Geraedts <p.f.j.geraedts@gmail.com>
Pawel Dembicki [Fri, 1 Mar 2024 09:47:36 +0000 (10:47 +0100)]
ls-mc: bump to 10.38.0
Update ls-mc to latest 10.38.0 version.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Pawel Dembicki [Fri, 1 Mar 2024 09:44:48 +0000 (10:44 +0100)]
ls-dpl: bump to 10.38.0
Update ls-dpl to latest 10.38.0 version.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
INAGAKI Hiroshi [Thu, 22 Feb 2024 10:00:57 +0000 (19:00 +0900)]
ath79: add support for ELECOM WAB-I1750-PS
ELECOM WAB-I1750-PS is a 2.4/5 GHz band 11ac (Wi-Fi 5) access point,
based on QCA9558.
Specification:
- SoC : Qualcomm Atheros QCA9558
- RAM : DDR2 128 MiB (2x Winbond W9751G6KB251)
- Flash : SPI-NOR 16 MiB (Macronix MX25L12835FMI-10G)
- WLAN : 2.4/5 GHz 3T3R
- 2.4 GHz : Qualcomm Atheros QCA9558 (SoC)
- 5 GHz : Qualcomm Atheros QCA9880
- Ethernet : 2x 10/100/1000 Mbps
- phy ("PD") : Atheros AR8035
- phy ("PSE") : Atheros AR8033
- LEDs/keys (GPIO) : 3x/3x
- UART : 2x RJ-45 port
- "SERVICE" : TTL (3.3V)
- port : ttyS0
- assignment : 1:3.3V, 2:GND, 3:TX, 4:RX
- settings : 115200n8
- note : no compatibility with "Cisco console cable"
- "SERIAL" : RS232C (+-12V)
- port : ?
- assignment : 1:NC , 2:NC , 3:TXD, 4:GND,
5:GND, 6:RXD, 7:NC , 8:NC
- settings : 115200n8
- note : compatible with "Cisco console cable"
- Buzzer : 1x GPIO-controlled
- USB : 1x USB 2.0 Type-A
- Power : DC jack or PoE
- DC jack : 12 VDC, 1.04 A (device only, rating)
- PoE : 802.3af/at, 48 VDC, 0.26 A (device only, rating)
- note : supports 802.3af supply on PSE (downstream) port
when powered by DC adapter or 802.3at PoE
Flash instruction using factory.bin image:
1. Boot WAB-I1750-PS without no upstream connection (or PoE connection
without DHCP)
2. Access to the WebUI ("http://192.168.3.1") on the device and open
firmware update page
("ツールボックス" -> "ファームウェア更新")
3. Select the OpenWrt factory.bin image and click update
("アップデート") button
4. Wait ~120 seconds to complete flashing
Revert to OEM firmware:
1. Download the latest OEM firmware
2. Remove 128 bytes(0x80) header from firmware image
3. Decode by xor with a pattern "
8844a2d168b45a2d" (hex val)
4. Upload the decoded firmware to the device
5. Flash to "firmware" partition by mtd command
6. Reboot
Notes:
- To use the "SERVICE" port, the connection of 3.3V line is also
required to enable console output.
The uart line of "SERVICE" is branched out from the internal pin
header with 74HC126D and 3.3V line is connected to OE pin on it.
- "SERIAL" port is provided by HS UART on QCA9558 SoC that has
compatibility with qca,ar9330-uart, but QCA955x SoC's is not supported
on Linux Kernel and OpenWrt.
- To supply 802.3af PoE on "PSE" port when powered by DC adapter, 12 VDC
3.5 A adapter is recommended. (official: WAB-EX-ADP1)
MAC addresses:
Ethernet (PD, PSE): 00:90:FE:xx:xx:0A (Config, ethaddr (text))
2.4GHz : 00:90:FE:xx:xx:0A (Config, ethaddr (text))
5GHz : 00:90:FE:xx:xx:0B
[original work]
Signed-off-by: Yanase Yuki <dev@zpc.st>
[update for NVMEM and others]
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
INAGAKI Hiroshi [Thu, 22 Feb 2024 10:00:57 +0000 (19:00 +0900)]
ath79: add support for ELECOM WAB-S1167-PS
ELECOM WAB-S1167-PS is a 2.4/5 GHz band 11ac (Wi-Fi 5) access point,
based on QCA9557.
Specification:
- SoC : Qualcomm Atheros QCA9557
- RAM : DDR2 128 MiB (2x Winbond W9751G6KB251)
- Flash : SPI-NOR 16 MiB (Macronix MX25L12835FMI-10G)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Qualcomm Atheros QCA9557 (SoC)
- 5 GHz : Qualcomm Atheros QCA9882
- Ethernet : 2x 10/100/1000 Mbps
- phy ("PD") : Atheros AR8035
- phy ("PSE") : Atheros AR8033
- LEDs/keys (GPIO) : 3x/3x
- UART : 1x RJ-45 port
- "SERVICE" : TTL (3.3V)
- port : ttyS0
- assignment : 1:3.3V, 2:GND, 3:TX, 4:RX
- settings : 115200n8
- note : no compatibility with "Cisco console cable"
- Buzzer : 1x GPIO-controlled
- USB : 1x USB 2.0 Type-A
- Power : DC jack or PoE
- DC jack : 12 VDC, 1 A (device only, rating)
- PoE : 802.3af/at, 48 VDC, 0.25 A (device only, rating)
- note : supports 802.3af supply on PSE (downstream) port
when powered by DC adapter or 802.3at PoE
Flash instruction using factory.bin image:
1. Boot WAB-S1167-PS without no upstream connection (or PoE connection
without DHCP)
2. Access to the WebUI ("http://192.168.3.1") on the device and open
firmware update page
("ツールボックス" -> "ファームウェア更新")
3. Select the OpenWrt factory.bin image and click update
("アップデート") button
4. Wait ~120 seconds to complete flashing
Revert to OEM firmware:
1. Download the latest OEM firmware
2. Remove 128 bytes(0x80) header from firmware image
3. Decode by xor with a pattern "
8844a2d168b45a2d" (hex val)
4. Upload the decoded firmware to the device
5. Flash to "firmware" partition by mtd command
6. Reboot
Notes:
- To use the "SERVICE" port, the connection of 3.3V line is also
required to enable console output.
The uart line of "SERVICE" is branched out from the internal pin
header with 74HC126D and 3.3V line is connected to OE pin on it.
- The same PCB is used with WAB-S600-PS.
- To supply 802.3af PoE on "PSE" port when powered by DC adapter, 12 VDC
3.5 A adapter is recommended. (official: WAB-EX-ADP1)
MAC addresses:
Ethernet (PD, PSE): 00:90:FE:xx:xx:04 (Config, ethaddr (text))
2.4GHz : 00:90:FE:xx:xx:04 (Config, ethaddr (text))
5GHz : 00:90:FE:xx:xx:05
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
INAGAKI Hiroshi [Thu, 22 Feb 2024 10:00:57 +0000 (19:00 +0900)]
ath79: add support for ELECOM WAB-S600-PS
ELECOM WAB-S600-PS is a 2.4/5 GHz band 11n (Wi-Fi 4) access point, based
on QCA9557.
This device also supports 11ac (Wi-Fi 5) with the another official
firmware.
Specification:
- SoC : Qualcomm Atheros QCA9557
- RAM : DDR2 128 MiB (2x Winbond W9751G6KB251)
- Flash : SPI-NOR 16 MiB (Macronix MX25L12835FMI-10G)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Qualcomm Atheros QCA9557 (SoC)
- 5 GHz : Qualcomm Atheros QCA9882
- Ethernet : 2x 10/100/1000 Mbps
- phy ("PD") : Atheros AR8035
- phy ("PSE") : Atheros AR8033
- LEDs/keys (GPIO) : 3x/3x
- UART : 1x RJ-45 port
- "SERVICE" : TTL (3.3V)
- port : ttyS0
- assignment : 1:3.3V, 2:GND, 3:TX, 4:RX
- settings : 115200n8
- note : no compatibility with "Cisco console cable"
- Buzzer : 1x GPIO-controlled
- USB : 1x USB 2.0 Type-A
- Power : DC jack or PoE
- DC jack : 12 VDC, 1 A (device only, rating)
- PoE : 802.3af/at, 48 VDC, 0.25 A (device only, rating)
- note : supports 802.3af supply on PSE (downstream) port
when powered by DC adapter or 802.3at PoE
Flash instruction using factory.bin image:
1. Boot WAB-S600-PS without no upstream connection (or PoE connection
without DHCP)
2. Access to the WebUI ("http://192.168.3.1") on the device and open
firmware update page
("ツールボックス" -> "ファームウェア更新")
3. Select the OpenWrt factory.bin image and click update
("アップデート") button
4. Wait ~120 seconds to complete flashing
Revert to OEM firmware:
1. Download the latest OEM firmware
2. Remove 128 bytes(0x80) header from firmware image
3. Decode by xor with a pattern "
8844a2d168b45a2d" (hex val)
4. Upload the decoded firmware to the device
5. Flash to "firmware" partition by mtd command
6. Reboot
Notes:
- To use the "SERVICE" port, the connection of 3.3V line is also
required to enable console output.
The uart line of "SERVICE" is branched out from the internal pin
header with 74HC126D and 3.3V line is connected to OE pin on it.
- The same PCB is used with WAB-S1167-PS.
- To supply 802.3af PoE on "PSE" port when powered by DC adapter, 12 VDC
3.5 A adapter is recommended. (official: WAB-EX-ADP1)
MAC addresses:
Ethernet (PD, PSE): BC:5C:4C:xx:xx:7C (Config, ethaddr (text))
2.4GHz : BC:5C:4C:xx:xx:7C (Config, ethaddr (text))
5GHz : BC:5C:4C:xx:xx:7D
[original work of common dtsi part for WAB-I1750-PS]
Signed-off-by: Yanase Yuki <dev@zpc.st>
[adding support for WAB-S600-PS]
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
David Bentham [Sun, 24 Dec 2023 13:49:50 +0000 (13:49 +0000)]
ramips: Unielec u7621-01: remove invalid led status
The original commit had an invalid setting of the
led status for this device.
There is no gpio pin connected to that led so lets
remove these from the u7621-01 dtsi file.
Signed-off-by: David Bentham <db260179@gmail.com>
Tim Harvey [Thu, 2 Mar 2023 22:29:39 +0000 (14:29 -0800)]
octeontx: update default network config
Update the default network configuration for Gateworks Newport boards
such that the left-most front-panel NIC is WAN and any additional are in
LAN bridge:
- gw610x/gw6903; single NIC: eth0
- gw620x/gw630x; two NIC's from left to right are: eth1 eth0
- gw640x; multiple NIC's from left to right: eth4 eth0 eth1 eth2 eth3
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Christian Lamparter [Sat, 17 Feb 2024 20:16:12 +0000 (21:16 +0100)]
apm821xx: MBL DUO-only: enable USB-Storage for boot from USB support
it is possible to boot and run OpenWrt from an image on an USB-Stick
on the MyBook Live DUO. (No, the MyBook Live Single does NOT have an
USB-Port and attempts at enabling it sadly all failed... so far).
To do that:
First, prepare a USB-Stick by writing the raw and uncompressed OpenWRT
factory image for the device onto the stick (i.e.
# gunzip -c openwrt-*wd_mybooklive*-factory.img.gz > /dev/sd$XX).
Then enter the u-boot via an attached TTL/CMOS 3.3V cable adapter and
give the following commands a try in the:
usb start; sata init
ext2load usb 0:1 ${fdt_addr_r} /boot/apollo3g.dtb
ext2load usb 0:1 ${kernel_addr_r} /boot/uImage
setenv bootargs 'root=/dev/sdc2 rw rootfstype=squashfs,ext4 rootdelay=5'
run addtty; bootm ${kernel_addr_r} - ${fdt_addr_r}
Notes:
- booting from USB-Sticks takes a long time! Be prepared to wait a few
minutes. (~3 minutes for 4 MiB /boot/uImage file on a USB 2.0 Stick)
- the bootargs part 'root=/dev/sdX2' depends on how many HDDs/SSDs are
slotted in. (if none: then use sda, if one: sdb. if two: sdc)
- rootdelay is important as the storage on the USB-Sticks do not show
up fast enough. 5 seconds might be excessive though.
- it's possible to concat these commands together in one line and
write it into u-boot's "bootcmd" environment variable and save the
environment to make the device to always boot from USB from then on.
if you have accidentally overridden the 'bootcmd' and want to return
to 'spec' enter the following commands :
setenv bootcmd 'run boot_sata_script_ap2nc'
saveenv
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Christian Lamparter [Fri, 9 Jun 2023 18:34:02 +0000 (20:34 +0200)]
apm821xx: add u-boot,env compatible
Note about the MyBook Live.
The MyBook Live didn't have the encompassing fixed-partitions.
This is needed for the u-boot,env compatible to be read as otherwise
the kernel assumes this is a legacy NOR/NAND node and this binding
is unsupported.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Christian Lamparter [Sat, 17 Feb 2024 19:52:41 +0000 (20:52 +0100)]
apm821xx: remove 5.15 remnants
deletes config-5.15 and patches-5.15/.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Christian Lamparter [Sat, 17 Feb 2024 19:51:13 +0000 (20:51 +0100)]
apm821xx: make 6.1 kernel default
6.1 has been available for some time for testing.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Robert Marko [Fri, 1 Mar 2024 18:51:24 +0000 (19:51 +0100)]
qualcommax: enable DEBUG_BUGVERBOSE
Enable DEBUG_BUGVERBOSE by default on qualcommax as without it once BUG()
is called we will not get any output other than
"------------[ cut here ]------------"
which is not usefull at all, so since we dont have kernel size constraints
lets enable it by default.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Eneas U de Queiroz [Fri, 16 Feb 2024 17:32:07 +0000 (14:32 -0300)]
build: scripts/config - update to kconfig-v6.6.16
The main goal here is to keep this close to upstream.
Changes include:
- allow symbols implied by y to become m
- make 'imply' obey the direct dependency
- allow only 'config', 'comment', and 'if' inside 'choice'
- qconf: make search fully work again on split mode
- qconf: navigate menus on hyperlinks
- remove '---help---' support
- qconf: allow to edit "int", "hex", "string" menus in-place
- qconf: drop Qt4 support
- nconf: fix core dump when searching in empty menu
- nconf: stop endless search loops
- Create links to main menu items in search
- fix segmentation fault in menuconfig search
- nconf: Add search jump feature
- port qconf to work with Qt6 in addition to Qt5
- fix possible buffer overflow
- fix memory leak from range properties
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Pawel Dembicki [Fri, 1 Mar 2024 08:04:00 +0000 (09:04 +0100)]
layerscape: remove 5.15 kernel support
Kernel was switched to 6.1. Lets drop 5.15 support.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Pawel Dembicki [Fri, 1 Mar 2024 08:01:45 +0000 (09:01 +0100)]
layerscape: switch kernel to 6.1 version
It was testing since couple months. Lets switch it to 6.1 by default for
wide testing.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Cedric DOURLENT [Fri, 1 Mar 2024 15:42:34 +0000 (16:42 +0100)]
build: fix kernel component in CycloneDX SBOM
As stated in the cycloneDX documentation, the field "type" is mandatory for all components.
More details here (https://cyclonedx.org/docs/1.5/json/#components_items_type)
Signed-off-by: Cedric DOURLENT <cedric.dourlent@softathome.com>
Daniel Golle [Fri, 1 Mar 2024 00:06:47 +0000 (00:06 +0000)]
mediatek: mt7622: rtl8367c: add casts to fix compiler warnings
Use type casts to prevent compiler warnings which are going to turn
into errors when we switch to Linux 6.6.
In the long run we should try to get rid of this downstream driver
now that RTL8367S is support by the rtl8365mb DSA driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Thu, 29 Feb 2024 23:52:56 +0000 (23:52 +0000)]
mediatek: rename or replace accepted patches
Rename kernel patches accepted upstream to indicate at which version
they have been accepted, replacing downstream variants which what was
accepted upstream. Note that some of them are fixes which will
find their way to older kernel versions as well via linux-stable.
No functional changes.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Thu, 29 Feb 2024 19:30:10 +0000 (19:30 +0000)]
mediatek: fix version tag in thermal patches
Some backported thermal patches ended up with the wrong kernel
version in their filename. Fix this.
Fixes: c36de2e73a ("mediatek: backport a hell of thermal commits")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Thu, 29 Feb 2024 19:22:43 +0000 (19:22 +0000)]
uboot-mediatek: remove rootfs_data before attempting to replace fip
Make sure there is enough space to replace 'fip' volume and always
remove rootfs_data before.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Linus Walleij [Fri, 23 Feb 2024 07:23:47 +0000 (08:23 +0100)]
kirkwood: Add Marvell RTC to all machines with nothing else
The Kirkwood SoCs all have an onchip RTC that can hold the time
over e.g. a reboot which will help if no NTP servers are available.
Create a kernel module package for the Marvell RTC, and add it to
all Kirkwood devices that do not have their own discrete
battery-backed RTC. Adding it to platforms with a proper RTC
is just surplus.
All Kirkwoods have at least one RTC so add RTC to the features
list for Kirkwood as well.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Samuele Longhi [Fri, 23 Feb 2024 09:36:58 +0000 (10:36 +0100)]
ath79: nand: add SUPPORTED_DEVICES for Meraki MR18
This adds the board name from ar71xx to support upgrade without
-F for the Meraki MR18.
Signed-off-by: Samuele Longhi <agave@dracaena.it>
Mieczyslaw Nalewaj [Fri, 23 Feb 2024 20:23:05 +0000 (21:23 +0100)]
ramips: fix nvmem-cells for routers based on TP-Link Archer
Added missing nvmem-cells located in the loaded file mt7620a_tplink_archer.dtsi
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Robert Senderek [Fri, 16 Feb 2024 13:04:40 +0000 (14:04 +0100)]
mediatek: filogic: add support for Cudy RE3000 v1
MT7981B /256MB /16MB SPI (XM25QH128C)
AX 2.4Ghz
AX 5Ghz 160Mhz wide
1Gbit LAN
OEM:
root@RE3000:~# ifconfig |grep HWaddr
br-lan Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0 (label)
br-wan Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
eth0 Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
ra0 Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
ra2 Link encap:Ethernet HWaddr 82:XX:XX:28:XX:X0
rax0 Link encap:Ethernet HWaddr 82:XX:XX:38:XX:X0
rax2 Link encap:Ethernet HWaddr 82:XX:XX:58:XX:X0
OpenWrt
root@OpenWrt:/# ifconfig |grep HW
br-lan Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
eth0 Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
phy0-ap0 Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
phy1-ap0 Link encap:Ethernet HWaddr 82:XX:XX:08:XX:X1
tftp Installation via u-boot:
Connect TTL3.3V converter
connector is under the radiator Set speed 115200 8 N 1
Interrupt boot process by holding down-arrow key during boot then
>> 6. Load image
>> 0 - TFTP client (Default)
enter IP adresses and initramfs-kernel.bin
write to flash via sysupgrade or gui
Signed-off-by: Robert Senderek <robert.senderek@10g.pl>
Zoltan HERPAI [Thu, 29 Feb 2024 16:06:04 +0000 (17:06 +0100)]
uboot-d1: cleanup Makefile
Clean up leftover PKG_HASH.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Zoltan HERPAI [Wed, 24 May 2023 21:51:14 +0000 (23:51 +0200)]
d1: add new target
This target adds support for the Allwinner D1 RISC-V based SoCs.
- RISC-V single-core T-Head C906 (RV64GCV)
- Tensilica HiFi4 DSP
- DDR2/DDR3 support
- 10/100/1000M ethernet
- usual peripherals like USB2, SPI, I2C, PWM, etc.
Four boards are supported:
- Dongshan Nezha STU
- 512Mb RAM
- ethernet
- LicheePi RV Dock
- 512Mb RAM
- wireless-only (RTL8723DS)
- MangoPi MQ-Pro
- 512Mb RAM
- there are pads available for an SPI flash
- wireless-only (RTL8723DS)
- Nezha D1
- 512Mb/1Gb/2Gb RAM
- 256Mb NAND flash
- ethernet, wireless
Installation:
Standard SD-card installation via dd-ing the generated image to
an SD-card of at least 256Mb.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Zoltan HERPAI [Wed, 7 Jun 2023 12:34:06 +0000 (14:34 +0200)]
uboot-d1: add bootloader for upcoming d1 target
Add u-boot bootloader based on 2023.01 to support D1-based boards, currently:
- Dongshan Nezha STU
- LicheePi RV Dock
- MangoPi MQ-Pro
- Nezha D1
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Zoltan HERPAI [Wed, 7 Jun 2023 09:54:34 +0000 (11:54 +0200)]
opensbi: allow building on upcoming d1 target
U-boot on D1 also uses OpenSBI as its payload. As the current version of
OpenSBI already supports D1 with no further patches required, allow
building it on the upcoming TARGET_d1 too.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Rafał Miłecki [Wed, 28 Feb 2024 10:51:02 +0000 (11:51 +0100)]
base-files: sysupgrade: add uci-defaults script disabling services #2
Disabled services should be kept disabled after sysupgrade. This can be
easily handled using a proper uci-defaults script.
Extend sysupgrade to check for disabled services, generate uci-defaults
script disabling them and include it in backup.
Cc: Christian Marangi <ansuelsmth@gmail.com>
Cc: Jo-Philipp Wich <jo@mein.io>
Cc: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Jo-Philipp Wich <jo@mein.io>
Rafał Miłecki [Wed, 28 Feb 2024 10:51:01 +0000 (11:51 +0100)]
base-files: sysupgrade: use tar helper to include installed_packages.txt
Replace mount + overlay with manually built tar archive that gets
prepended to the actual config files backup. This allows more
flexibility with including extra backup files. They can be included at
any paths and don't require writing to flash or mounting an overlay
which has its own limitations (mount points).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Jo-Philipp Wich <jo@mein.io>
Jo-Philipp Wich [Wed, 28 Feb 2024 10:51:00 +0000 (11:51 +0100)]
base-files: sysupgrade: add tar.sh with helpers for building archives
This allows building uncompressed tar archives from shell scripts (and
compressing them later if needed)
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
[rmilecki: adapt to sysupgrade needs]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Tony Ambardar [Wed, 28 Feb 2024 23:04:57 +0000 (15:04 -0800)]
tools/dwarves: update to 1.26
Release Notes:
https://lore.kernel.org/dwarves/
20240228193921.JWQp1Mc2M47ffhgIjnHKh8538u4uztVKuznlck9Pk9E@z/
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Felix Fietkau [Wed, 28 Feb 2024 08:52:08 +0000 (09:52 +0100)]
mediatek: re-enable mt7622-rfb1-ubi with changed partition layout
The boot loader does not have a fixed size limit for the kernel,
so we're free to change the layout. This may break sysupgrade, but a fresh
flash from initramfs works.
Fixes: 6e2962d4c548 ("mediatek: mt7622: skip build for MT7622 rfb1 (UBI)")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Tianling Shen [Sun, 25 Feb 2024 12:21:40 +0000 (20:21 +0800)]
uboot-mediatek: correct board name for BananaPi BPi-R3 Mini
It should be "BananaPi BPi-R3 Mini" instead of just "BananaPi BPi-R3".
Fixes: bc25519f98cd ("uboot-mediatek: add builds for BananaPi BPi-R3 mini")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Michael Seibt [Mon, 5 Feb 2024 23:40:21 +0000 (00:40 +0100)]
build: fix shebang line
Remove space between sharp-exclamation and interpreter.
Signed-off-by: Michael Seibt <github@roboschmie.de>
Daniel Huici [Sun, 4 Feb 2024 22:59:48 +0000 (23:59 +0100)]
lantiq: add support for Arcadyan VRV9510KWAC23
The Arcadyan VRV9510KWAC23 (trade name Livebox Next) is a Lantiq router distributed by some spanish ISPs
Hardware:
- SoC: Lantiq VRX200
- CPU: 2x MIPS 34Kc 500 MHz
- RAM: 256 MiB DDR2
- Flash: 128 MiB NAND
- Ethernet: Built-in Gigabit Ethernet switch, 5x 1GbE
- Wifi 2.4GHz: Broadcom BCM43222KFBG 802.11b/g/b MIMO 2T2R
- Wifi 5GHz: Broadcom BCM4360KMLG 802.11ac MIMO 3T3R
- USB: 2x USB 2.0
- DSL: Built-in VDSL/ADSL2+ XWAY VRX208
- LEDs: 8x
- Buttons: 4x
- Phone: Lantiq PEF 42068 V XWAY SLIC120
Install instructions:
Detailed instructions can be found on the wiki https://openwrt.org/toh/arcadyan/vrv9510kwac23
1. Boot into UART mode and upload the the https://raw.githubusercontent.com/danielhuici/arcadyan-vrv9510kwac23-utils/main/u-boot.asc file via serial console to boot into U-Boot.
2. Perform a backup of the NAND
3. Setup a TFTP server and serve the https://github.com/danielhuici/arcadyan-vrv9510kwac23-utils/raw/main/u-boot.ltq.lzo.nandspl. Replace the OEM bootloader with this one. Erase your NAND and write the image into it
4. Reboot the router
5. Serve the OpenWrt ramdisk image on your TFTP server and boot it via U-Boot
6. When OpenWrt boots, flash the SquashFS OpenWrt image using LuCi interface, so OpenWrt gets installed into the NAND
Signed-off-by: Daniel Huici <danielhuici@hotmail.com>
projects / openwrt / staging / blogic.git / log