Eric W. Biederman [Fri, 19 Jun 2015 19:03:39 +0000 (14:03 -0500)]
netfilter: nf_qeueue: Drop queue entries on nf_unregister_hook
Add code to nf_unregister_hook to flush the nf_queue when a hook is
unregistered. This guarantees that the pointer that the nf_queue code
retains into the nf_hook list will remain valid while a packet is
queued.
I tested what would happen if we do not flush queued packets and was
trivially able to obtain the oops below. All that was required was
to stop the nf_queue listening process, to delete all of the nf_tables,
and to awaken the nf_queue listening process.
> BUG: unable to handle kernel paging request at
0000000100000001
> IP: [<
0000000100000001>] 0x100000001
> PGD
b9c35067 PUD 0
> Oops: 0010 [#1] SMP
> Modules linked in:
> CPU: 0 PID: 519 Comm: lt-nfqnl_test Not tainted
> task:
ffff8800b9c8c050 ti:
ffff8800ba9d8000 task.ti:
ffff8800ba9d8000
> RIP: 0010:[<
0000000100000001>] [<
0000000100000001>] 0x100000001
> RSP: 0018:
ffff8800ba9dba40 EFLAGS:
00010a16
> RAX:
ffff8800bab48a00 RBX:
ffff8800ba9dba90 RCX:
ffff8800ba9dba90
> RDX:
ffff8800b9c10128 RSI:
ffff8800ba940900 RDI:
ffff8800bab48a00
> RBP:
ffff8800b9c10128 R08:
ffffffff82976660 R09:
ffff8800ba9dbb28
> R10:
dead000000100100 R11:
dead000000200200 R12:
ffff8800ba940900
> R13:
ffffffff8313fd50 R14:
ffff8800b9c95200 R15:
0000000000000000
> FS:
00007fb91fc34700(0000) GS:
ffff8800bfa00000(0000) knlGS:
0000000000000000
> CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
> CR2:
0000000100000001 CR3:
00000000babfb000 CR4:
00000000000007f0
> Stack:
>
ffffffff8206ab0f ffffffff82982240 ffff8800bab48a00 ffff8800b9c100a8
>
ffff8800b9c10100 0000000000000001 ffff8800ba940900 ffff8800b9c10128
>
ffffffff8206bd65 ffff8800bfb0d5e0 ffff8800bab48a00 0000000000014dc0
> Call Trace:
> [<
ffffffff8206ab0f>] ? nf_iterate+0x4f/0xa0
> [<
ffffffff8206bd65>] ? nf_reinject+0x125/0x190
> [<
ffffffff8206dee5>] ? nfqnl_recv_verdict+0x255/0x360
> [<
ffffffff81386290>] ? nla_parse+0x80/0xf0
> [<
ffffffff8206c42c>] ? nfnetlink_rcv_msg+0x13c/0x240
> [<
ffffffff811b2fec>] ? __memcg_kmem_get_cache+0x4c/0x150
> [<
ffffffff8206c2f0>] ? nfnl_lock+0x20/0x20
> [<
ffffffff82068159>] ? netlink_rcv_skb+0xa9/0xc0
> [<
ffffffff820677bf>] ? netlink_unicast+0x12f/0x1c0
> [<
ffffffff82067ade>] ? netlink_sendmsg+0x28e/0x650
> [<
ffffffff81fdd814>] ? sock_sendmsg+0x44/0x50
> [<
ffffffff81fde07b>] ? ___sys_sendmsg+0x2ab/0x2c0
> [<
ffffffff810e8f73>] ? __wake_up+0x43/0x70
> [<
ffffffff8141a134>] ? tty_write+0x1c4/0x2a0
> [<
ffffffff81fde9f4>] ? __sys_sendmsg+0x44/0x80
> [<
ffffffff823ff8d7>] ? system_call_fastpath+0x12/0x6a
> Code: Bad RIP value.
> RIP [<
0000000100000001>] 0x100000001
> RSP <
ffff8800ba9dba40>
> CR2:
0000000100000001
> ---[ end trace
08eb65d42362793f ]---
Cc: stable@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric W. Biederman [Fri, 19 Jun 2015 15:41:21 +0000 (10:41 -0500)]
netfilter: nftables: Do not run chains in the wrong network namespace
Currenlty nf_tables chains added in one network namespace are being
run in all network namespace. The issues are myriad with the simplest
being an unprivileged user can cause any network packets to be dropped.
Address this by simply not running nf_tables chains in the wrong
network namespace.
Cc: stable@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pankaj Gupta [Fri, 19 Jun 2015 14:17:53 +0000 (19:47 +0530)]
macvtap: Increase limit of macvtap queues
Macvtap should be compatible with tuntap for
maximum number of queues.
commit '
baf71c5c1f80d82e92924050a60b5baaf97e3094 (tuntap:
Increase the number of queues in tun.)' removes
the limitations and increases number of queues in tuntap.
Now, Its safe to increase number of queues in Macvtap as well.
This patch also modifies 'macvtap_del_queues' function
to avoid extra memory allocation in stack.
Changes from v1->v2 :
Michael S. Tsirkin, Jason Wang :
Better way to use linked list to
avoid use of extra memory in stack.
Sergei Shtylyov : Specify dependent commit's summary.
Signed-off-by: Pankaj Gupta <pagupta@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Wagner [Fri, 19 Jun 2015 14:00:44 +0000 (16:00 +0200)]
bpf: BPF based latency tracing
BPF offers another way to generate latency histograms. We attach
kprobes at trace_preempt_off and trace_preempt_on and calculate the
time it takes to from seeing the off/on transition.
The first array is used to store the start time stamp. The key is the
CPU id. The second array stores the log2(time diff). We need to use
static allocation here (array and not hash tables). The kprobes
hooking into trace_preempt_on|off should not calling any dynamic
memory allocation or free path. We need to avoid recursivly
getting called. Besides that, it reduces jitter in the measurement.
CPU 0
latency : count distribution
1 -> 1 : 0 | |
2 -> 3 : 0 | |
4 -> 7 : 0 | |
8 -> 15 : 0 | |
16 -> 31 : 0 | |
32 -> 63 : 0 | |
64 -> 127 : 0 | |
128 -> 255 : 0 | |
256 -> 511 : 0 | |
512 -> 1023 : 0 | |
1024 -> 2047 : 0 | |
2048 -> 4095 : 166723 |*************************************** |
4096 -> 8191 : 19870 |*** |
8192 -> 16383 : 6324 | |
16384 -> 32767 : 1098 | |
32768 -> 65535 : 190 | |
65536 -> 131071 : 179 | |
131072 -> 262143 : 18 | |
262144 -> 524287 : 4 | |
524288 ->
1048575 : 1363 | |
CPU 1
latency : count distribution
1 -> 1 : 0 | |
2 -> 3 : 0 | |
4 -> 7 : 0 | |
8 -> 15 : 0 | |
16 -> 31 : 0 | |
32 -> 63 : 0 | |
64 -> 127 : 0 | |
128 -> 255 : 0 | |
256 -> 511 : 0 | |
512 -> 1023 : 0 | |
1024 -> 2047 : 0 | |
2048 -> 4095 : 114042 |*************************************** |
4096 -> 8191 : 9587 |** |
8192 -> 16383 : 4140 | |
16384 -> 32767 : 673 | |
32768 -> 65535 : 179 | |
65536 -> 131071 : 29 | |
131072 -> 262143 : 4 | |
262144 -> 524287 : 1 | |
524288 ->
1048575 : 364 | |
CPU 2
latency : count distribution
1 -> 1 : 0 | |
2 -> 3 : 0 | |
4 -> 7 : 0 | |
8 -> 15 : 0 | |
16 -> 31 : 0 | |
32 -> 63 : 0 | |
64 -> 127 : 0 | |
128 -> 255 : 0 | |
256 -> 511 : 0 | |
512 -> 1023 : 0 | |
1024 -> 2047 : 0 | |
2048 -> 4095 : 40147 |*************************************** |
4096 -> 8191 : 2300 |* |
8192 -> 16383 : 828 | |
16384 -> 32767 : 178 | |
32768 -> 65535 : 59 | |
65536 -> 131071 : 2 | |
131072 -> 262143 : 0 | |
262144 -> 524287 : 1 | |
524288 ->
1048575 : 174 | |
CPU 3
latency : count distribution
1 -> 1 : 0 | |
2 -> 3 : 0 | |
4 -> 7 : 0 | |
8 -> 15 : 0 | |
16 -> 31 : 0 | |
32 -> 63 : 0 | |
64 -> 127 : 0 | |
128 -> 255 : 0 | |
256 -> 511 : 0 | |
512 -> 1023 : 0 | |
1024 -> 2047 : 0 | |
2048 -> 4095 : 29626 |*************************************** |
4096 -> 8191 : 2704 |** |
8192 -> 16383 : 1090 | |
16384 -> 32767 : 160 | |
32768 -> 65535 : 72 | |
65536 -> 131071 : 32 | |
131072 -> 262143 : 26 | |
262144 -> 524287 : 12 | |
524288 ->
1048575 : 298 | |
All this is based on the trace3 examples written by
Alexei Starovoitov <ast@plumgrid.com>.
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: linux-kernel@vger.kernel.org
Cc: netdev@vger.kernel.org
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Fri, 19 Jun 2015 08:45:50 +0000 (01:45 -0700)]
bridge: multicast: start querier timer when running user-space stp
When STP is running in user-space and querier is configured, the
querier timer is not started when a port goes to a non-blocking state.
This patch unifies the user- and kernel-space stp multicast port enable
path and enables it in all states different from blocking. Note that when a
port goes in BR_STATE_DISABLED it's not enabled because that is handled
in the beginning of the port list loop.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 23 Jun 2015 10:24:58 +0000 (03:24 -0700)]
Merge tag 'nfc-next-4.2-2' of git://git./linux/kernel/git/sameo/nfc-next
NFC 4.2 2nd pull request
This one only contains a one liner fix for a typo that I
introduced while cleaning some of the nfcmrvl patches that
were part of the 1st 4.2 pull request.
David S. Miller [Tue, 23 Jun 2015 10:17:47 +0000 (03:17 -0700)]
Merge branch 'for-upstream' of git://git./linux/kernel/git/bluetooth/bluetooth-next
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-06-18
Here's the final bluetooth-next pull request for 4.2.
- Cleanups & fixes to 802.15.4 code and related drivers
- Fix btusb driver memory leak
- New USB IDs for Atheros controllers
- Support for BCM4324B3 UART based Broadcom controller
- Fix for Bluetooth encryption key size handling
- Broadcom controller initialization fixes
- Support for Intel controller DDC parameters
- Support for multiple Bluetooth LE advertising instances
- Fix for HCI user channel cleanup path
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Mahesh Bandewar [Thu, 18 Jun 2015 18:30:54 +0000 (11:30 -0700)]
bonding: Display LACP info only to CAP_NET_ADMIN capable user
Actor and Partner details can be accessed via proc-fs, sys-fs
entries or netlink interface. These interfaces are world readable
at this moment. The earlier patch-series made the LACP communication
secure to avoid nuisance attack from within the same L2 domain but
it did not prevent "someone unprivileged" looking at that information
on host and perform the same act.
This patch essentially avoids spitting those entries if the user
in question does not have enough privileges.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 23 Jun 2015 08:24:48 +0000 (01:24 -0700)]
Merge branch 'macb-sama5d2'
Nicolas Ferre says:
====================
net/macb: add sama5d2 support
This series is basically the support for another flavor of the GEM IP
configuration. It ended up being a series because of some little fixes made to
the binding documentation before adding the new compatibility string.
Bye,
v2: - fix bindings
- add sama5d2 compatibility string to the binding documentation
====================
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cyrille Pitchen [Thu, 18 Jun 2015 14:27:23 +0000 (16:27 +0200)]
net/macb: add config for Atmel sama5d2 SoCs
Add the compatible string for Atmel sama5d2 SoC family as the configuration
options differ from other instances of the GEM.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Ferre [Thu, 18 Jun 2015 14:27:22 +0000 (16:27 +0200)]
net/macb: bindings doc: add sama5d2 compatibility sting
Add sama5d2 to the biding documentation for this use of the GEM IP.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Ferre [Thu, 18 Jun 2015 14:27:21 +0000 (16:27 +0200)]
net/macb: bindings doc/trivial: fix sama5d4 comment
On sama5d4, we only have a GEM IP that is configured to do 10/100 Mbits. So the
use of "Gigabit" can be confusing.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Ferre [Thu, 18 Jun 2015 14:27:20 +0000 (16:27 +0200)]
net/macb: bindings doc: fix compatibility string
In the driver and the DT bindings we use the "atmel" prefix. Fix it in the
binding documentation.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hiroaki SHIMODA [Thu, 18 Jun 2015 11:40:54 +0000 (20:40 +0900)]
inet_diag: Remove _bh suffix in inet_diag_dump_reqs().
inet_diag_dump_reqs() is called from inet_diag_dump_icsk() with BH
disabled. So no need to disable BH in inet_diag_dump_reqs().
Signed-off-by: Hiroaki Shimoda <shimoda.hiroaki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shengzhou Liu [Thu, 18 Jun 2015 08:42:47 +0000 (16:42 +0800)]
net/phy: Add support for Realtek RTL8211F
RTL8211F has different register definitions from RTL8211E.
Specially it needs to enable TXDLY in case of RGMII.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 23 Jun 2015 08:03:18 +0000 (01:03 -0700)]
Merge tag 'wireless-drivers-next-for-davem-2015-06-18' of git://git./linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
Major changes:
mwifiex:
* enhancements for AP mode: support verbose information in station
dump command and also information about AP link.
* enable power save by default
brcmfmac:
* fix module reload issue for PCIe
* improving msgbuf protocol for PCIe devices
* rework .get_station() cfg80211 callback operation
* determine interface combinations upon device feature support
ath9k:
* ath9k_htc: add support of channel switch
wil6210:
* add modparam for bcast ring size
* support hidden SSID
* add per-MCS Rx stats
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Scott Feldman [Wed, 17 Jun 2015 23:08:31 +0000 (16:08 -0700)]
switchdev: fdb filter_dev is always NULL for self (device), so remove check
Remove the filter_dev check when dumping fdb entries, otherwise dump
returns empty list. filter_dev is always passed as NULL when dumping fdbs
on SELF. We want the fdbs installed on the device to be listed in the
dump.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Fixes: 45d4122c ("switchdev: add support for fdb add/del/dump via switchdev_port_obj ops")
Acked-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 21 Jun 2015 17:29:07 +0000 (10:29 -0700)]
Merge branch 'bna-cleanups'
Ivan Vecera says:
====================
bna: clean-up 2
Next round of cleaning patches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Vecera [Wed, 17 Jun 2015 16:41:58 +0000 (18:41 +0200)]
bna: remove superfluous parentheses
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Vecera [Wed, 17 Jun 2015 16:41:57 +0000 (18:41 +0200)]
bna: make pointers to read-only inputs const
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Vecera [Wed, 17 Jun 2015 16:41:56 +0000 (18:41 +0200)]
bna: remove unnecessary cast of BIT value
BIT value is already unsigned so casting is not necessary.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roopa Prabhu [Wed, 17 Jun 2015 18:07:01 +0000 (11:07 -0700)]
ipv4: include NLM_F_APPEND flag in append route notifications
This patch adds NLM_F_APPEND flag to struct nlmsg_hdr->nlmsg_flags
in newroute notifications if the route add was an append.
(This is similar to how NLM_F_REPLACE is already part of new
route replace notifications today)
This helps userspace determine if the route add operation was
an append.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Herrmann [Wed, 17 Jun 2015 15:14:33 +0000 (17:14 +0200)]
netlink: add API to retrieve all group memberships
This patch adds getsockopt(SOL_NETLINK, NETLINK_LIST_MEMBERSHIPS) to
retrieve all groups a socket is a member of. Currently, we have to use
getsockname() and look at the nl.nl_groups bitmask. However, this mask is
limited to 32 groups. Hence, similar to NETLINK_ADD_MEMBERSHIP and
NETLINK_DROP_MEMBERSHIP, this adds a separate sockopt to manager higher
groups IDs than 32.
This new NETLINK_LIST_MEMBERSHIPS option takes a pointer to __u32 and the
size of the array. The array is filled with the full membership-set of the
socket, and the required array size is returned in optlen. Hence,
user-space can retry with a properly sized array in case it was too small.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Craig Gallek [Wed, 17 Jun 2015 14:59:10 +0000 (10:59 -0400)]
sock_diag: fetch source port from inet_sock
When an inet_sock is destroyed, its source port (sk_num) is set to
zero as part of the unhash procedure. In order to supply a source
port as part of the NETLINK_SOCK_DIAG socket destruction broadcasts,
the source port number must be read from inet_sport instead.
Tested: ss -E
Signed-off-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Antonio Borneo [Wed, 17 Jun 2015 11:42:31 +0000 (19:42 +0800)]
net: via/Kconfig: replace USE_OF with OF_???
USE_OF is used as intermediate Kconfig option by few
arch's (ARM, MIPS, Xtensa).
Replace instances of USE_OF outside of arch folders
with proper OF_???.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Antonio Borneo [Wed, 17 Jun 2015 11:41:22 +0000 (19:41 +0800)]
net: via-rhine: remove unneeded include file
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Zhaowei Yuan [Wed, 17 Jun 2015 09:56:27 +0000 (17:56 +0800)]
net: Update out-of-date comment
Struct inet_proto no longer exists, so update the
comment which is out of date.
Signed-off-by: Zhaowei Yuan <zhaowei.yuan@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai [Wed, 17 Jun 2015 09:10:04 +0000 (14:40 +0530)]
cxgb4: Add PCI device ID for custom T522 & T520 adapter
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Tue, 16 Jun 2015 23:51:43 +0000 (16:51 -0700)]
Modify Liquidio Kconfig for crc lib
Following patch contains changes in liquidio Kconfig for
selecting LIBCRC32C.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kees Cook [Tue, 16 Jun 2015 22:36:17 +0000 (15:36 -0700)]
cxgb3: avoid needless buffer copy for firmware
There's no reason to perform a buffer copy for the firmware name. This
also avoids a (currently impossible with current callers) NULL dereference
if there was no matching firmware.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrea Parri [Tue, 16 Jun 2015 22:16:59 +0000 (00:16 +0200)]
pkt_sched: sch_qfq: remove redundant -if- control statement
The control !hlist_unhashed() in qfq_destroy_agg() is unnecessary
because already performed in hlist_del_init(), so remove it.
Signed-off-by: Andrea Parri <parri.andrea@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julien Grall [Tue, 16 Jun 2015 19:10:48 +0000 (20:10 +0100)]
net/xen-netback: Don't mix hexa and decimal with 0x in the printf format
Append 0x to all %x in order to avoid while reading when there is other
decimal value in the log.
Also replace some of the hexadecimal print to decimal to uniformize the
format with netfront.
Signed-off-by: Julien Grall <julien.grall@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: netdev@vger.kernel.org
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julien Grall [Tue, 16 Jun 2015 19:10:47 +0000 (20:10 +0100)]
net/xen-netback: Remove unused code in xenvif_rx_action
The variables old_req_cons and ring_slots_used are assigned but never
used since commit
1650d5455bd2dc6b5ee134bd6fc1a3236c266b5b "xen-netback:
always fully coalesce guest Rx packets".
Signed-off-by: Julien Grall <julien.grall@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Julien Grall [Tue, 16 Jun 2015 19:10:46 +0000 (20:10 +0100)]
net/xen-netfront: Correct printf format in xennet_get_responses
rx->status is an int16_t, print it using %d rather than %u in order to
have a meaningful value when the field is negative.
Also use %u rather than %x for rx->offset.
Signed-off-by: Julien Grall <julien.grall@citrix.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Fabian Frederick [Tue, 16 Jun 2015 18:44:07 +0000 (20:44 +0200)]
net: rds: use for_each_sg() for scatterlist parsing
This patch also renames sg to sglist and aligns function parameters.
See Documentation/DMA-API.txt - Part Id for scatterlist details
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Tue, 16 Jun 2015 16:51:37 +0000 (12:51 -0400)]
packet: free packet_rollover after synchronize_net
Destruction of the po->rollover must be delayed until there are no
more packets in flight that can access it. The field is destroyed in
packet_release, before synchronize_net. Delay using rcu.
Fixes: 0648ab70afe6 ("packet: rollover prepare: per-socket state")
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 20 Jun 2015 22:39:40 +0000 (15:39 -0700)]
Merge git://git./linux/kernel/git/pablo/nf-next
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains a final Netfilter pull request for net-next
4.2. This mostly addresses some fallout from the previous pull request, small
netns updates and a couple of new features for nfnetlink_log and the socket
match that didn't get in time for the previous pull request. More specifically
they are:
1) Add security context information to nfnetlink_queue, from Roman Kubiak.
2) Add support to restore the sk_mark into skb->mark through xt_socket,
from Harout Hedeshian.
3) Force alignment of 16 bytes of per cpu xt_counters, from Eric Dumazet.
4) Rename br_netfilter.c to br_netfilter_hooks.c to prepare split of IPv6 code
into a separated file.
5) Move the IPv6 code in br_netfilter into a separated file.
6) Remove unused RCV_SKB_FAIL() in nfnetlink_queue and nfetlink_log, from Eric
Biederman.
7) Two liner to simplify netns logic in em_ipset_match().
8) Add missing includes to net/net_namespace.h to avoid compilation problems
that result from not including linux/netfilter.h in netns headers.
9) Use a forward declaration instead of including linux/proc_fs.h from
netns/netfilter.h
10) Add a new linux/netfilter_defs.h to replace the linux/netfilter.h inclusion
in netns headers.
11) Remove spurious netfilter.h file included in the net tree, also from Eric
Biederman.
12) Fix x_tables compilation warnings on 32 bits platforms that resulted from
recent changes in x_tables counters, from Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal [Wed, 17 Jun 2015 21:58:28 +0000 (23:58 +0200)]
netfilter: xtables: fix warnings on 32bit platforms
On 32bit archs gcc complains due to cast from void* to u64.
Add intermediate casts to long to silence these warnings.
include/linux/netfilter/x_tables.h:376:10: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
include/linux/netfilter/x_tables.h:384:15: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
include/linux/netfilter/x_tables.h:391:23: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
include/linux/netfilter/x_tables.h:400:22: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Fixes: 71ae0dff02d756e ("netfilter: xtables: use percpu rule counters")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Eric W Biederman [Wed, 17 Jun 2015 15:28:35 +0000 (10:28 -0500)]
netfilter: Remove spurios included of netfilter.h
While testing my netfilter changes I noticed several files where
recompiling unncessarily because they unncessarily included
netfilter.h.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pablo Neira Ayuso [Wed, 17 Jun 2015 15:28:27 +0000 (10:28 -0500)]
netfilter: don't pull include/linux/netfilter.h from netns headers
This pulls the full hook netfilter definitions from all those that include
net_namespace.h.
Instead let's just include the bare minimum required in the new
linux/netfilter_defs.h file, and use it from the netfilter netns header files.
I also needed to include in.h and in6.h from linux/netfilter.h otherwise we hit
this compilation error:
In file included from include/linux/netfilter_defs.h:4:0,
from include/net/netns/netfilter.h:4,
from include/net/net_namespace.h:22,
from include/linux/netdevice.h:43,
from net/netfilter/nfnetlink_queue_core.c:23:
include/uapi/linux/netfilter.h:76:17: error: field ‘in’ has incomplete type struct in_addr in;
And also explicit include linux/netfilter.h in several spots.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Pablo Neira Ayuso [Wed, 17 Jun 2015 15:28:26 +0000 (10:28 -0500)]
netfilter: use forward declaration instead of including linux/proc_fs.h
We don't need to pull the full definitions in that file, a simple forward
declaration is enough.
Moreover, include linux/procfs.h from nf_synproxy_core, otherwise this hits a
compilation error due to missing declarations, ie.
net/netfilter/nf_synproxy_core.c: In function ‘synproxy_proc_init’:
net/netfilter/nf_synproxy_core.c:326:2: error: implicit declaration of function ‘proc_create’ [-Werror=implicit-function-declaration]
if (!proc_create("synproxy", S_IRUGO, net->proc_net_stat,
^
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Pablo Neira Ayuso [Wed, 17 Jun 2015 15:28:25 +0000 (10:28 -0500)]
net: include missing headers in net/net_namespace.h
Include linux/idr.h and linux/skbuff.h since they are required by objects that
are declared in the net structure.
struct net {
...
struct idr netns_ids;
...
struct sk_buff_head wext_nlevents;
...
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Eric W. Biederman [Wed, 17 Jun 2015 15:28:17 +0000 (10:28 -0500)]
net: sched: Simplify em_ipset_match
em->net is always set and always available, use it in preference
to dev_net(skb->dev).
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Eric W. Biederman [Wed, 17 Jun 2015 15:28:10 +0000 (10:28 -0500)]
netfilter: Kill unused copies of RCV_SKB_FAIL
This appears to have been a dead macro in both nfnetlink_log.c and
nfnetlink_queue_core.c since these pieces of code were added in 2005.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pablo Neira Ayuso [Tue, 16 Jun 2015 12:07:03 +0000 (14:07 +0200)]
netfilter: bridge: split ipv6 code into separated file
Resolve compilation breakage when CONFIG_IPV6 is not set by moving the IPv6
code into a separated br_netfilter_ipv6.c file.
Fixes: efb6de9b4ba0 ("netfilter: bridge: forward IPv6 fragmented packets")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Johan Hedberg [Thu, 18 Jun 2015 18:05:31 +0000 (21:05 +0300)]
Bluetooth: Fix warning of potentially uninitialized adv_instance variable
Rework the logic of checking for a valid adv_instance for non-zero
cp->instance values. Without this change we may get (false positive)
warnings as follows:
>> net/bluetooth/mgmt.c:7294:29: warning: 'adv_instance' may be used
uninitialized in this function [-Wuninitialized]
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Thu, 18 Jun 2015 17:50:08 +0000 (20:50 +0300)]
Bluetooth: Use zalloc when possible
Use zallog for adv_instance allocation instead of kmalloc + memset.
This also fixes the following coccinelle warning:
>> net/bluetooth/hci_core.c:2693:17-24: WARNING: kzalloc should be
used for adv_instance, instead of kmalloc/memset
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Dmitry Tunin [Thu, 18 Jun 2015 17:41:51 +0000 (20:41 +0300)]
Bluetooth: ath3k: Add support of 04ca:300d AR3012 device
BugLink: https://bugs.launchpad.net/bugs/1394368
This device requires new firmware files
AthrBT_0x11020100.dfu and ramps_0x11020100_40.dfu added to
/lib/firmware/ar3k/ that are not included in linux-firmware yet.
T: Bus=02 Lev=01 Prnt=01 Port=04 Cnt=03 Dev#= 5 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=04ca ProdID=300d Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
Marcel Holtmann [Thu, 18 Jun 2015 16:58:03 +0000 (18:58 +0200)]
Bluetooth: Increment management interface revision
This patch increments the management interface revision due to
introduction of new multi-advertising feature and various bug fixes.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Florian Grandel [Thu, 18 Jun 2015 01:16:53 +0000 (03:16 +0200)]
Bluetooth: hci_core: increase max adv inst
Now that all preconditions are present for actual multi-advertising, the
number of allowed advertising instances can be larger than one. This
patch increases the number of allowed advertising instances to 5.
Signed-off-by: Florian Grandel <fgrandel@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Florian Grandel [Thu, 18 Jun 2015 01:16:52 +0000 (03:16 +0200)]
Bluetooth: hci_core: remove obsolete adv_instance
Now that the obsolete adv_instance is no longer being referenced
anywhere in the code it can be removed without breaking the build.
Signed-off-by: Florian Grandel <fgrandel@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Florian Grandel [Thu, 18 Jun 2015 01:16:51 +0000 (03:16 +0200)]
Bluetooth: mgmt: multi-adv for mgmt_reenable_advertising()
During service discovery, advertising will be disabled. This patch
ensures that it is correctly being re-enabled, both for configuration
made via set advertising and add advertising, once the scanning
times out.
Signed-off-by: Florian Grandel <fgrandel@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Florian Grandel [Thu, 18 Jun 2015 01:16:50 +0000 (03:16 +0200)]
Bluetooth: mgmt: multi-adv for trigger_le_scan()
This patch ensures that instance advertising is correctly canceled
before starting a le scan.
Signed-off-by: Florian Grandel <fgrandel@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Florian Grandel [Thu, 18 Jun 2015 01:16:49 +0000 (03:16 +0200)]
Bluetooth: mgmt: program multi-adv on power on
Advertising instances programmed while powered off should be advertised
once the device is powered. This patch ensures that all combinations
of setting and/or adding advertising configuration while powered off
will be correctly activated on power on.
Signed-off-by: Florian Grandel <fgrandel@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Florian Grandel [Thu, 18 Jun 2015 01:16:48 +0000 (03:16 +0200)]
Bluetooth: mgmt: multi adv for remove_advertising*()
The remove_advertising() and remove_advertising_complete() functions
had instance identifiers hard coded. Notably, when passing in 0x00 as
an instance identifier to signal that all instances should be removed
then the mgmt API would return a hard coded 0x01 rather than returning
the expected value 0x00. This bug is being fixed by always referencing
the instance identifier from the management API call instead.
remove_advertising() is refactored to use the new dynamic advertising
instance list. The logic is being changed to make multi-instance
advertising actually work, notably the schedule_adv_instance() method is
being referenced to make sure that other instances will continue to
advertise even if one instance is being removed.
The code is made more readable by factoring advertising instance
management and initialization into the low-level
hci_remove_adv_instance() and hci_adv_instances_clear() functions.
The method now references the clear_adv_instance() helper method to
remove duplicate logic and code.
Signed-off-by: Florian Grandel <fgrandel@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Florian Grandel [Thu, 18 Jun 2015 01:16:47 +0000 (03:16 +0200)]
Bluetooth: mgmt/hci_core: multi-adv for add_advertising*()
The add_advertising() and add_advertising_complete() functions reference
the now obsolete hdev->adv_instance struct. Both methods are being
refactored to access the dynamic advertising instance list instead.
This patch also introduces all logic necessary to actually deal with
multiple instance advertising. Notably the mgmt_adv_inst_expired() and
schedule_adv_inst() method are being referenced to schedule instances in
a round robin fashion.
This patch also introduces a "pending" flag into the adv_info struct.
This is necessary to identify and remove recently added advertising
instances when the HCI commands return with an error status code.
Otherwise new advertising instances could be leaked without properly
informing userspace about their existence.
Signed-off-by: Florian Grandel <fgrandel@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Florian Grandel [Thu, 18 Jun 2015 01:16:46 +0000 (03:16 +0200)]
Bluetooth: mgmt: multi adv for clear_adv_instances()
The clear_adv_instance() function could not clean up multiple
advertising instances previously. It is being changed to provide both, a
means to clean up a single instance and cleaning up all instances at
once.
An additional instance parameter is being introduced to achieve this.
Passing in 0x00 to this parameter signifies that all instances should be
cleaned up. This semantics has been chosen similarly to the semantics of
the instance parameter in the remove_advertising() function.
When removing a single instance the method also ensures that another
instance will be scheduled if available. When the currently advertising
method is being removed, it will be canceled immediately.
Signed-off-by: Florian Grandel <fgrandel@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Florian Grandel [Thu, 18 Jun 2015 01:16:45 +0000 (03:16 +0200)]
Bluetooth: mgmt: multi adv for set_advertising*()
The set_advertising() and set_advertising_complete() methods rely on
the now obsolete hci_dev->adv_instance structure. We replace this
reference by an equivalent access to the newly introduced dynamic
advertising instance list.
This patch introduces a helper function that schedules an advertising
instance correctly calculating advertising timing based on the timeout
and duration settings of the instance. Scheduling is factored into
its own function for readability and code sharing.
Signed-off-by: Florian Grandel <fgrandel@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Florian Grandel [Thu, 18 Jun 2015 01:16:44 +0000 (03:16 +0200)]
Bluetooth: mgmt: multi adv for create_instance_adv_data()
The create_instance_adv_data() function could not deal with
multiple advertising instances previously. This is being fixed by
retrieving advertising instances from the newly introduced dynamic
advertising instance list.
Signed-off-by: Florian Grandel <fgrandel@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Florian Grandel [Thu, 18 Jun 2015 01:16:43 +0000 (03:16 +0200)]
Bluetooth: mgmt: multi adv for create_instance_scan_rsp_data()
The create_instance_scan_rsp_data() function could not deal with
multiple advertising instances previously. This is being fixed by adding
an additional instance parameter.
Signed-off-by: Florian Grandel <fgrandel@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Florian Grandel [Thu, 18 Jun 2015 01:16:42 +0000 (03:16 +0200)]
Bluetooth: mgmt: multi adv for enable_advertising()
Previously enable_advertising() would rely on
get_adv_instance_scan_rsp_len() which checked for a hard coded instance
identifier. This is being changed to check for the current advertising
instance's scan response length instead. The function is renamed
accordingly.
Signed-off-by: Florian Grandel <fgrandel@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Florian Grandel [Thu, 18 Jun 2015 01:16:41 +0000 (03:16 +0200)]
Bluetooth: mgmt: improve get_adv_instance_flags() readability
Switch if and else conditions to replace a negative statement by a
positive one which makes the condition more readable.
Signed-off-by: Florian Grandel <fgrandel@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Florian Grandel [Thu, 18 Jun 2015 01:16:40 +0000 (03:16 +0200)]
Bluetooth: mgmt: multi adv for get_adv_instance_flags()
The get_adv_instance_flags() would not work with instance identifiers
other than 0x01. This is being fixed so that arbitrary instance
identifiers can be dealt with while still correctly dealing with the
special case of the 0x00 identifier.
Signed-off-by: Florian Grandel <fgrandel@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Florian Grandel [Thu, 18 Jun 2015 01:16:39 +0000 (03:16 +0200)]
Bluetooth: mgmt: multi adv for get_current_adv_instance()
Replaces the hard coded instance identifier in
get_current_adv_instance() with the actual current instance identifier
so that this method is prepared to work with more than one advertising
instance.
Signed-off-by: Florian Grandel <fgrandel@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Florian Grandel [Thu, 18 Jun 2015 01:16:38 +0000 (03:16 +0200)]
Bluetooth: mgmt: multi adv for read_adv_features()
The read_adv_features() method had a single instance identifier hard
coded. Refer to the advertising instance list instead to return a
dynamically generated list of instance identifiers.
Signed-off-by: Florian Grandel <fgrandel@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Florian Grandel [Thu, 18 Jun 2015 01:16:37 +0000 (03:16 +0200)]
Bluetooth: mgmt: rename update_*_data_for_instance()
The ...for_instance function name is quite long and does not follow the
..._inst_... convention followed elsewhere in the code. This patch
renames the ...for_instance functions to their shorter ..._inst_...
version.
Signed-off-by: Florian Grandel <fgrandel@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Florian Grandel [Thu, 18 Jun 2015 01:16:36 +0000 (03:16 +0200)]
Bluetooth: mgmt: dry update_scan_rsp_data()
update_scan_rsp_data() duplicates code from get_current_adv_instance().
This is being fixed by letting the former make use of the latter.
Signed-off-by: Florian Grandel <fgrandel@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Florian Grandel [Thu, 18 Jun 2015 01:16:35 +0000 (03:16 +0200)]
Bluetooth: hci_core/mgmt: move adv timeout to hdev
Currently the delayed work managing advertising duration and timeout is
part of the advertising instance structure. This is not correct as only
a single instance can be advertised at any given time. To implement
round robin advertising a single delayed work structure is needed.
To fix this the delayed work structure is being moved to the hci_dev
structure. The instance specific variable is renamed to "remaining_time"
to make it clear that this is the remaining lifetime of the instance and
not the current advertising timeout.
Signed-off-by: Florian Grandel <fgrandel@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Florian Grandel [Thu, 18 Jun 2015 01:16:34 +0000 (03:16 +0200)]
Bluetooth: hci_core/mgmt: Introduce multi-adv list
The current hci dev structure only supports a single advertising
instance. To support multi-instance advertising it is necessary to
introduce a linked list of advertising instances so that multiple
advertising instances can be dynamically added and/or removed.
In a first step, the existing adv_instance member of the hci_dev
struct is supplemented by a linked list of advertising instances.
This patch introduces the list and supporting list management
infrastructure. The list is not being used yet.
Signed-off-by: Florian Grandel <fgrandel@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Prasanna Karthik [Thu, 18 Jun 2015 13:51:11 +0000 (13:51 +0000)]
Bluetooth: bt3c_cs: Fix coding style -- clean up
Fix for braces {} are not necessary for single statement blocks
reported by checkpatch
Signed-off-by: Prasanna Karthik <mkarthi3@visteon.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Frederic Danis [Thu, 18 Jun 2015 10:43:27 +0000 (12:43 +0200)]
Bluetooth: hci_uart: Fix speed selection
hu->proto->*speed will always be used for all device where it is set.
But hu->*speed should be used if exist, so the test should be swapped.
The equivalent change is needed in bcm_setup() of hci_bcm.c.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Pablo Neira Ayuso [Tue, 16 Jun 2015 11:38:26 +0000 (13:38 +0200)]
netfilter: bridge: rename br_netfilter.c to br_netfilter_hooks.c
To prepare separation of the IPv6 code into different file.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Eric Dumazet [Tue, 16 Jun 2015 01:10:13 +0000 (18:10 -0700)]
netfilter: x_tables: align per cpu xt_counter
Let's force a 16 bytes alignment on xt_counter percpu allocations,
so that bytes and packets sit in same cache line.
xt_counter being exported to user space, we cannot add __align(16) on
the structure itself.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Harout Hedeshian [Tue, 16 Jun 2015 00:40:43 +0000 (18:40 -0600)]
netfilter: xt_socket: add XT_SOCKET_RESTORESKMARK flag
xt_socket is useful for matching sockets with IP_TRANSPARENT and
taking some action on the matching packets. However, it lacks the
ability to match only a small subset of transparent sockets.
Suppose there are 2 applications, each with its own set of transparent
sockets. The first application wants all matching packets dropped,
while the second application wants them forwarded somewhere else.
Add the ability to retore the skb->mark from the sk_mark. The mark
is only restored if a matching socket is found and the transparent /
nowildcard conditions are satisfied.
Now the 2 hypothetical applications can differentiate their sockets
based on a mark value set with SO_MARK.
iptables -t mangle -I PREROUTING -m socket --transparent \
--restore-skmark -j action
iptables -t mangle -A action -m mark --mark 10 -j action2
iptables -t mangle -A action -m mark --mark 11 -j action3
Signed-off-by: Harout Hedeshian <harouth@codeaurora.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Roman Kubiak [Fri, 12 Jun 2015 10:32:57 +0000 (12:32 +0200)]
netfilter: nfnetlink_queue: add security context information
This patch adds an additional attribute when sending
packet information via netlink in netfilter_queue module.
It will send additional security context data, so that
userspace applications can verify this context against
their own security databases.
Signed-off-by: Roman Kubiak <r.kubiak@samsung.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
David S. Miller [Thu, 18 Jun 2015 10:57:44 +0000 (03:57 -0700)]
Merge branch 'master' of git://git./linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
This series contains updates to fm10k only.
Alex provides two fixes for the fm10k, first folds the fm10k_pull_tail()
call into fm10k_add_rx_frag(), this way the fragment does not have to be
modified after it is added to the skb. The second fixes missing braces
to an if statement.
The remaining patches are from Jacob which contain improvements and fixes
for fm10k. First fix makes it so that invalid address will simply be
skipped and allows synchronizing the full list to proceed with using
iproute2 tool. Fixed a possible kernel panic by using the correct
transmit timestamp function. Simplified the code flow for setting the
IN_PROGRESS bit of the shinfo for an skb that we will be timestamping.
Fix a bug in the timestamping transmit enqueue code responsible for a
NULL pointer dereference and invalid access of the skb list by freeing
the clone in the cases where we did not add it to the queue. Update the
PF code so that it resets the empty TQMAP/RQMAP regirsters post-VFLR to
prevent innocent VF drivers from triggering malicious driver events.
The SYSTIME_CFG.Adjust direction bit is actually supposed to indicate
that the adjustment is positive, so fix the code to align correctly with
the hardware and documentation. Cleanup local variable that is no longer
used after a previous refactor of the code. Fix the code flow so that we
actually clear the enabled flag as part of our removal of the LPORT.
v2:
- updated patch 07 description based on feedback from Sergei Shtylyov
- updated patch 09 & 10 to use %d in error message based on feedback
from Sergei Shtylyov
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Romain Perier [Mon, 15 Jun 2015 17:44:19 +0000 (17:44 +0000)]
net: stmmac: dwmac-rk: Don't add function name in info or err messages
These kind of informations are only useful for debugging and should not be
displayed in normal modules message.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ilya Faenson [Wed, 17 Jun 2015 21:30:56 +0000 (17:30 -0400)]
Bluetooth: hci_uart: Add new line discipline enhancements
Added the ability to flow control the UART, improved the UART baud
rate setting, transferred the speeds into line discipline from the
protocol and introduced the tty init function.
Signed-off-by: Ilya Faenson <ifaenson@broadcom.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Alexander Duyck [Thu, 4 Jun 2015 01:53:17 +0000 (18:53 -0700)]
fm10k: Fix missing braces after if statement
While reviewing the code I noticed that one of the commits added an if
statement followed by a for loop, but the if statement was missing the
braces around the loop. This change corrects the coding style error.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Wed, 3 Jun 2015 23:31:12 +0000 (16:31 -0700)]
fm10k: fix iov_msg_lport_state_pf issue
When a VF issues an LPORT_STATE request to enable a port that is already
enabled, the PF will first disable the VF LPORT. Then it should
re-enable the VF again with the new requested settings. This ensures
that any switch rules are cleared by deleting the LPORT on the switch.
However, the flow is bugged because we actually check if the VF is
enabled at the end, and thus don't re-enable it. Fix the flow so that we
actually clear the enabled flags as part of our removal of the LPORT.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Wed, 3 Jun 2015 23:31:11 +0000 (16:31 -0700)]
fm10k: remove err_no reference in fm10k_mbx.c
The reference to err_no was left around after a previous code refactor.
We never use the value, and it doesn't seem to be used in side a hidden
macro reference. Discovered via cppcheck.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Wed, 3 Jun 2015 23:31:10 +0000 (16:31 -0700)]
fm10k: fix incorrect DIR_NEVATIVE bit in 1588 code
The SYSTIME_CFG.Adjust Direction bit is actually supposed to indicate
that the adjustment is positive. Fix the code to align correctly with
hardware and documentation.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Wed, 3 Jun 2015 23:31:09 +0000 (16:31 -0700)]
fm10k: pack TLV overlay structures
This patch adds the __attribute__((packed)) indicator to some structures
which are overlayed onto a TLV message. These structures must be packed
as small as possible in order to correctly align when copied into the
mailbox buffer. Without doing so, the receiving mailbox code incorrectly
parses the values and we get invalid message responses from the switch
manager software.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Wed, 3 Jun 2015 23:31:08 +0000 (16:31 -0700)]
fm10k: re-map all possible VF queues after a VFLR
During initialization, the VF counts its rings by walking the TQDLOC
registers. This works only if the TQMAP/RQMAP registers are set to map
all of the out-of-bound rings back to the first one. This allows the VF
to cleanly detect when it has run out of queues. Update the PF code so
that it resets the empty TQMAP/RQMAP registers post-VFLR to prevent
innocent VF drivers from triggering malicious driver events.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Wed, 3 Jun 2015 23:31:07 +0000 (16:31 -0700)]
fm10k: force LPORT delete when updating VLAN or MAC address
Currently, we don't notify the switch at all when the PF
administratively sets a new VLAN or MAC address. This causes the old
addresses to remain valid on the switch table. Since the PF is
overriding any configuration done directly by the VF, we choose to
simply re-create the LPORT for the VF. This does mean that all rules for
the VF will be dropped when we set something directly via the PF, but it
prevents some weird issues where the MAC/VLAN table retains some stale
configuration.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Tue, 16 Jun 2015 20:41:43 +0000 (13:41 -0700)]
fm10k: use dma_set_mask_and_coherent in fm10k_probe
This patch cleans up the use of dma_get_required_mask and uses the
simpler dma_set_mask_and_coherent function instead of doing these as
separate steps.
I removed the dma_get_required_mask call because based on some minimal
testing it appears that either (a) we're not doing the right thing with
the call or (b) we don't need it anyways. If the value returned is
<48bits, we'll end up trying with 48 bits anyways. If it's over 48bits,
fm10k can't support that anyways, and we should try 48bits. If 48bits
fails, we'll fallback to 32bits. This cleans up some very funky code.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Tue, 16 Jun 2015 20:40:32 +0000 (13:40 -0700)]
fm10k: trivial fixup message style to include a colon
Also use %d for error values, since printing in hexadecimal is probably
not helpful.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Wed, 3 Jun 2015 23:31:04 +0000 (16:31 -0700)]
fm10k: remove extraneous NULL check on l2_accel
l2_accel was checked for NULL at the top of fm10k_dfwd_del_station, and
we return if it is not defined. Due to this, we already know it can't be
null here so a separate check is meaningless. Discovered via cppcheck.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Tue, 16 Jun 2015 20:39:11 +0000 (13:39 -0700)]
fm10k: use an unsigned int for i in ethtool_get_strings
The value will never be negative, and we use the %u print format. Thus,
use unsigned int for the loop counter. Issue found using cppcheck.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Wed, 3 Jun 2015 23:31:02 +0000 (16:31 -0700)]
fm10k: add call to fm10k_clean_all_rx_rings in fm10k_down
This prevents a memory leak in fm10k_set_ringparams. The leak occurs
because we go down, change ring parameters, and then come up. However,
fm10k_down on its own is not clearing the Rx rings. Since fm10k_up
assumes the rings are clean we basically drop the buffers and leak a
bunch of memory. Eventually we hit dirty page faults and reboot the
system. This issue does not occur elsewhere because other flows that
involve fm10k_down go through fm10k_close which immediately called
fm10k_free_all_rx_resources which properly cleans the rings.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Wed, 3 Jun 2015 23:31:01 +0000 (16:31 -0700)]
fm10k: fix incorrect free on skb in ts_tx_enqueue
This patch resolves a bug in the ts_tx_enqueue code responsible for a
NULL pointer dereference and invalid access of the skb list. We
incorrectly freed the actual skb we found instead of our copy. Thus the
skb queue is essentially invalidated. Resolve this by freeing our clone
in the cases where we did not add it to the queue. This also avoids the
skb memory leak caused by failure to free the clone.
[ 589.719320] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 589.722344] IP: [<
ffffffffa0310e60>] fm10k_ts_tx_subtask+0xb0/0x160 [fm10k]
[ 589.723796] PGD 0
[ 589.725228] Oops: 0000 [#1] SMP
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Wed, 3 Jun 2015 23:31:00 +0000 (16:31 -0700)]
fm10k: move setting shinfo inside ts_tx_enqueue
This patch simplifies the code flow for setting the IN_PROGRESS bit of
the shinfo for an skb we will be timestamping.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Wed, 3 Jun 2015 23:30:59 +0000 (16:30 -0700)]
fm10k: use correct ethernet driver Tx timestamp function
skb_complete_tx_timestamp is intended for use by PHY drivers which
implement a different method of returning timestamps. This method is
intended to be used after a PHY driver accepts a cloned packet via its
phy_driver.txtstamp function. It is not correct to use in the standard
ethernet driver such as fm10k. This patch fixes the following possible
kernel panic.
[ 2744.552896] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W OE 3.19.3-200.fc21.x86_64 #1
[ 2744.552899] Hardware name: Intel Corporation S2600CO/S2600CO, BIOS SE5C600.86B.02.03.8x23.
060520140825 06/05/2014
[ 2744.552901]
0000000000000000 2f4c8b10ea3f9848 ffff88081ee03a38 ffffffff8176e215
[ 2744.552906]
0000000000000000 0000000000000000 ffff88081ee03a78 ffffffff8109bc1a
[ 2744.552910]
ffff88081ee03c50 ffff88080e55fc00 ffff88080e55fc00 ffffffff81647c50
[ 2744.552914] Call Trace:
[ 2744.552917] <IRQ> [<
ffffffff8176e215>] dump_stack+0x45/0x57
[ 2744.552931] [<
ffffffff8109bc1a>] warn_slowpath_common+0x8a/0xc0
[ 2744.552936] [<
ffffffff81647c50>] ? skb_queue_purge+0x20/0x40
[ 2744.552941] [<
ffffffff8109bd4a>] warn_slowpath_null+0x1a/0x20
[ 2744.552946] [<
ffffffff81646911>] skb_release_head_state+0xe1/0xf0
[ 2744.552950] [<
ffffffff81647b26>] skb_release_all+0x16/0x30
[ 2744.552954] [<
ffffffff81647ba6>] kfree_skb+0x36/0x90
[ 2744.552958] [<
ffffffff81647c50>] skb_queue_purge+0x20/0x40
[ 2744.552964] [<
ffffffff81751f8d>] packet_sock_destruct+0x1d/0x90
[ 2744.552968] [<
ffffffff81642053>] __sk_free+0x23/0x140
[ 2744.552973] [<
ffffffff81642189>] sk_free+0x19/0x20
[ 2744.552977] [<
ffffffff81647d60>] skb_complete_tx_timestamp+0x50/0x60
[ 2744.552988] [<
ffffffffa02eee40>] fm10k_ts_tx_hwtstamp+0xd0/0x100 [fm10k]
[ 2744.552994] [<
ffffffffa02e054e>] fm10k_1588_msg_pf+0x12e/0x140 [fm10k]
[ 2744.553002] [<
ffffffffa02edf1d>] fm10k_tlv_msg_parse+0x8d/0xc0 [fm10k]
[ 2744.553010] [<
ffffffffa02eb2d0>] fm10k_mbx_dequeue_rx+0x60/0xb0 [fm10k]
[ 2744.553016] [<
ffffffffa02ebf98>] fm10k_sm_mbx_process+0x178/0x3c0 [fm10k]
[ 2744.553022] [<
ffffffffa02e09ca>] fm10k_msix_mbx_pf+0xfa/0x360 [fm10k]
[ 2744.553030] [<
ffffffff811030a7>] ? get_next_timer_interrupt+0x1f7/0x270
[ 2744.553036] [<
ffffffff810f2a47>] handle_irq_event_percpu+0x77/0x1a0
[ 2744.553041] [<
ffffffff810f2bab>] handle_irq_event+0x3b/0x60
[ 2744.553045] [<
ffffffff810f5d6e>] handle_edge_irq+0x6e/0x120
[ 2744.553054] [<
ffffffff81017414>] handle_irq+0x74/0x140
[ 2744.553061] [<
ffffffff810bb54a>] ? atomic_notifier_call_chain+0x1a/0x20
[ 2744.553066] [<
ffffffff8177777f>] do_IRQ+0x4f/0xf0
[ 2744.553072] [<
ffffffff8177556d>] common_interrupt+0x6d/0x6d
[ 2744.553074] <EOI> [<
ffffffff81609b16>] ? cpuidle_enter_state+0x66/0x160
[ 2744.553084] [<
ffffffff81609b01>] ? cpuidle_enter_state+0x51/0x160
[ 2744.553087] [<
ffffffff81609cf7>] cpuidle_enter+0x17/0x20
[ 2744.553092] [<
ffffffff810de101>] cpu_startup_entry+0x321/0x3c0
[ 2744.553098] [<
ffffffff81764497>] rest_init+0x77/0x80
[ 2744.553103] [<
ffffffff81d4f02c>] start_kernel+0x4a4/0x4c5
[ 2744.553107] [<
ffffffff81d4e120>] ? early_idt_handlers+0x120/0x120
[ 2744.553110] [<
ffffffff81d4e4d7>] x86_64_start_reservations+0x2a/0x2c
[ 2744.553114] [<
ffffffff81d4e62b>] x86_64_start_kernel+0x152/0x175
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Wed, 3 Jun 2015 23:30:58 +0000 (16:30 -0700)]
fm10k: ignore invalid multicast address entries
This change fixes an issue with adding an invalid multicast address
using the iproute2 tool (ip maddr add <MADDR> dev <dev>). The iproute2
tool and the kernel do not validate or filter the multicast addresses
when adding them to the multicast list. Thus, when synchronizing this
list with an invalid entry, the action will be aborted with an error
since the fm10k driver currently validates the list. Consequently,
multicast entries beyond the invalid one will not be processed and
communicated with the switch via the mailbox. This change makes it so
that invalid addresses will simply be skipped and allows synchronizing
the full list to proceed.
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Thu, 23 Apr 2015 04:49:25 +0000 (21:49 -0700)]
fm10k: fold fm10k_pull_tail into fm10k_add_rx_frag
This change folds the fm10k_pull_tail call into fm10k_add_rx_frag. The
advantage to doing this is that the fragment doesn't have to be modified
after it is added to the skb.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Glenn Ruben Bakke [Wed, 17 Jun 2015 14:32:27 +0000 (07:32 -0700)]
Bluetooth: 6lowpan: Fix module refcount
This patch removes the additional module_put() in disconnect_all_peers()
making a correct module refcount so that the module can be removed after
disabling 6lowpan through debugfs.
Signed-off-by: Lukasz Duda <lukasz.duda@nordicsemi.no>
Signed-off-by: Glenn Ruben Bakke <glenn.ruben.bakke@nordicsemi.no>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Glenn Ruben Bakke [Wed, 17 Jun 2015 14:32:26 +0000 (07:32 -0700)]
Bluetooth: 6lowpan: Fix double kfree of netdev priv
This patch removes the kfree of the netdev priv in device_event() upon
NETDEV_UNREGISTER event. The freeing of memory is taken care of by the
netdev destructor.
Signed-off-by: Lukasz Duda <lukasz.duda@nordicsemi.no>
Signed-off-by: Glenn Ruben Bakke <glenn.ruben.bakke@nordicsemi.no>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Glenn Ruben Bakke [Wed, 17 Jun 2015 14:32:25 +0000 (07:32 -0700)]
Bluetooth: 6lowpan: Move netdev sysfs device reference
This patch moves the sysfs device used by the netdev from the device of
the first connected peer to the hci sysfs device. Using the sysfs device
of hci instead of the first connected device fixes this issue such that
the sysfs group of tx-0 and bt0 kobject are still present after the last
peer has been deleted and all sysfs entries can be removed.
Signed-off-by: Lukasz Duda <lukasz.duda@nordicsemi.no>
Signed-off-by: Glenn Ruben Bakke <glenn.ruben.bakke@nordicsemi.no>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Glenn Ruben Bakke [Wed, 17 Jun 2015 14:32:24 +0000 (07:32 -0700)]
Bluetooth: 6lowpan: Rename ambiguous variable
This patch renames the variable used to trigger scheduling of
delete_netdev. Changed to infinitiv in order to describe the action
to be done.
Signed-off-by: Lukasz Duda <lukasz.duda@nordicsemi.no>
Signed-off-by: Glenn Ruben Bakke <glenn.ruben.bakke@nordicsemi.no>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Glenn Ruben Bakke [Wed, 17 Jun 2015 14:32:23 +0000 (07:32 -0700)]
Bluetooth: 6lowpan: Enable delete_netdev to be scheduled when last peer is deleted
This patch fixes an issue with the netdev not being unregistered when
the last peer is deleted. Removing the logical negation operator on the
boolean solves this issue. If the last peer is removed the condition
will be true, and the delete_netdev() is scheduled.
Signed-off-by: Lukasz Duda <lukasz.duda@nordicsemi.no>
Signed-off-by: Glenn Ruben Bakke <glenn.ruben.bakke@nordicsemi.no>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
projects / openwrt / staging / blogic.git / log