John Crispin [Tue, 26 Apr 2016 11:44:07 +0000 (11:44 +0000)]
mac80211: ath9k: add GPIO support for AR9280 chip
Enable access to GPIO on Atheros wireless chip AR9280.
Support for 9280 is added to existing 9285/9287 subsystem
because these 3 chips differ only in number of GPIO pins.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 49251
John Crispin [Tue, 26 Apr 2016 11:44:03 +0000 (11:44 +0000)]
lantiq: remove read-only flag on two partitions on BTHOMEHUBV3A
Remove read-only flag on two partitions on BTHOMEHUBV3A:
uboot-config - otherwise fw_setenv command cannot be used.
ath9k-cal - so that ath9k calibration data can be copied
to the partition on a newly installed board.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 49250
John Crispin [Tue, 26 Apr 2016 11:44:00 +0000 (11:44 +0000)]
cns3xxx: set both MPS 'and' MRSS to 128
Fixes some DMA issues with this platform. Because this isn't currently accepted,
and can potentially disrupt other platforms (as read in commit log), I will
leave this cns3xxx specific.
Original Patch: https://patchwork.ozlabs.org/patch/600024/
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
SVN-Revision: 49249
John Crispin [Tue, 26 Apr 2016 11:43:57 +0000 (11:43 +0000)]
cns3xxx: backport pci fix for cns3xxx_write_config
Fix is required to properly set pci config bits.
Original Patch: https://patchwork.ozlabs.org/patch/596170/
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
SVN-Revision: 49248
John Crispin [Tue, 26 Apr 2016 11:43:53 +0000 (11:43 +0000)]
ramips: Add support for the Netgear WNDR3700v5
https://wiki.openwrt.org/toh/netgear/wndr3700
wndr3700v5 uses the single-core dual thread MediaTek MT7621S SoC.
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 49247
John Crispin [Tue, 26 Apr 2016 11:43:49 +0000 (11:43 +0000)]
usbutils: Update USB IDs list and drop gzip compression
Change mirror to Github (Gentoo repo) and drop the gzip compression.
Worst case there's about 4kbyte increase in size but most images ends up
beign somewhere between 4-100kbyte smaller due to the lzma compression.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
SVN-Revision: 49246
John Crispin [Tue, 26 Apr 2016 11:43:45 +0000 (11:43 +0000)]
ar71xx: Add TP-Link TL-WR740N v6 support to trunk
This patch adds support for the TP-Link TL-WR740N v6 into OpenWrt trunk. Hardware wise, it's very similar to the TL-WR841N v10. See the forum thread [1]. Credit goes to the user 'traveler' who did the legwork and tested builds.
Also thanks to Matthias Schiffer for clarifying the DEVICE_PROFILE settings.
Signed-off by: Stijn Segers <francesco.borromini@inventati.org>
[1]: https://forum.openwrt.org/viewtopic.php?pid=318704
SVN-Revision: 49245
John Crispin [Tue, 26 Apr 2016 11:43:42 +0000 (11:43 +0000)]
ar71xx: simplify patch 613 and add missing error handling
Dynamic allocation of label can be simplified.
Also add error handling to deal with failed memory allocation.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 49244
John Crispin [Tue, 26 Apr 2016 11:43:38 +0000 (11:43 +0000)]
mediatek: update patches
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 49243
John Crispin [Tue, 26 Apr 2016 11:43:31 +0000 (11:43 +0000)]
lantiq: Fix typo in LED diag script.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
Acked-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 49242
John Crispin [Tue, 26 Apr 2016 11:43:28 +0000 (11:43 +0000)]
lantiq: use new image build process for brnImages
LZMA compress the kernel without dictionary, otherwise brnboot fails to
uncompress the kernel.
The filesystem parameter of mkbrncmdline was dropped since the used
filesystem isn't exported in the kernel build step and at least in my
tests everything works without the parameter. If the parameter is
required for some reason, the static keyword "squashfs" can be used.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 49241
John Crispin [Tue, 26 Apr 2016 11:43:24 +0000 (11:43 +0000)]
include: add a no dict version of lzma to new image build code
Required to compress kernels in a brnboot compatible way.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 49240
John Crispin [Tue, 26 Apr 2016 11:43:21 +0000 (11:43 +0000)]
lantiq: remove orphaned tp-link image build steps
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 49239
John Crispin [Tue, 26 Apr 2016 11:43:18 +0000 (11:43 +0000)]
lantiq: build sysupgrade images for lantiqImage
Tested with VGV7510KW22NOR.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 49238
John Crispin [Tue, 26 Apr 2016 11:43:15 +0000 (11:43 +0000)]
lantiq: new image build process - fix kernel entry address
Set the kernel entry address to the same value as it is used for the old
image build build process.
Fixes boot of uImages on VGV7510KW22NOR and others.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 49237
John Crispin [Tue, 26 Apr 2016 11:43:11 +0000 (11:43 +0000)]
lantiq: uboot-envtools on BTHOMEHUBV3A
Generate fw_env.config for BTHOMEHUBV3A.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 49236
John Crispin [Tue, 26 Apr 2016 11:43:06 +0000 (11:43 +0000)]
ramips: add support for Planex MZK-EX300NP
MZK-EX300NP is MT7620A based wifi repeater.
Built-in power supply.
64MiB RAM, 8MiB SPI Flash, non Wired Ethernet.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 49235
John Crispin [Tue, 26 Apr 2016 11:43:01 +0000 (11:43 +0000)]
ramips: add support for Planex CS-QR10
CS-QR10 is MT7620A based IP Camera.
the camera and sound does not work with kernel 4.4.
- camera chip is sn9c291.
- sound chip is wm8960.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 49234
Rafał Miłecki [Tue, 26 Apr 2016 09:23:12 +0000 (09:23 +0000)]
kernel: backport support for accelerated SPI flash read
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 49233
Rafał Miłecki [Tue, 26 Apr 2016 09:22:49 +0000 (09:22 +0000)]
bcm53xx: backport BCM5301X DT patch specifying SPI controller
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 49232
Jo-Philipp Wich [Mon, 25 Apr 2016 15:54:35 +0000 (15:54 +0000)]
fstools: respect mount flags for /overlay mounts
Respect user configured mount flags such as "ro" or "sync" when processing
external overlay mount points.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
SVN-Revision: 49223
Rafał Miłecki [Mon, 25 Apr 2016 15:32:20 +0000 (15:32 +0000)]
mac80211: add brcmfmac regression ("NULL pointer dereference") fix
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 49222
Hauke Mehrtens [Sun, 24 Apr 2016 22:17:38 +0000 (22:17 +0000)]
ramips: fix build of target
Makes the patches apply again by fixing the white space broken patch.
This problem was introduced in r49212.
Closes #22248 and #22259
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49221
Luka Perkov [Sun, 24 Apr 2016 16:42:14 +0000 (16:42 +0000)]
oxnas: add missing semicolon
A missing semicolon in the gpio-keys-polled section of ox820-akitio.dts
caused the build to break. Add it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 49219
John Crispin [Thu, 21 Apr 2016 19:47:26 +0000 (19:47 +0000)]
xtables-addons: build: fix configure compatiblity with POSIX shells
Fixes build with /bin/sh pointing to certain versions of dash (for example
on Void Linux).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 49218
John Crispin [Thu, 21 Apr 2016 19:47:22 +0000 (19:47 +0000)]
ar71xx: build TP-LINK Archer C7 images with US region code
Since December 2015, the Archer C7 comes with an US-specific firmware. This
firmware will only allow upgrades with images that contain the US region
code in the firmware header.
The "universal" firmware distributed in the rest of the world doesn't care
about the region code, so we can just unconditionally set the region to US
for now. When other region-specific firmwares appear, we'll need to create
a factory image for each of them.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 49217
John Crispin [Thu, 21 Apr 2016 19:47:19 +0000 (19:47 +0000)]
ar71xx: fix giving extra arguments to Build/mktplinkfw
The build command will always get the whole argument string in $(1),
regardless of whitespace. We need to use word/wordlist to split the string
after the first word.
Whitespace and quotation will be given to the command verbatim (make will
ignore it), so to give multiple arguments, no quotation marks may be used.
Fixes: r47174 ("ar71xx/image: add options argument to mktplinkfw step")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 49216
John Crispin [Thu, 21 Apr 2016 19:47:15 +0000 (19:47 +0000)]
tools: firmware-utils: add region code support to mktplinkfw
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 49215
John Crispin [Thu, 21 Apr 2016 19:47:12 +0000 (19:47 +0000)]
tools: firmware-utils: clean up mktplinkfw
Remove the whole board list from mktplinkfw, as OpenWrt doesn't use it and
it was severely out of sync with the list of built images for ar71xx.
Also:
* fix -Wall warnings
* add const where appropriate
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 49214
John Crispin [Thu, 21 Apr 2016 19:47:08 +0000 (19:47 +0000)]
ramips: Add support for ZBT WG3526
The WG3526 is the follow-up to the 2626 and is mostly the same, with the
excaption that the mt7602 has been replaced with the mt7603. The internal wifi
setup has also changed slightly. Based on my tests, everything that worked on
the 2626 works on the 3526 and with roughly the same performance.
v1->v2:
* Remove some references to 2626 that I had missed in the dts.
v2->v3:
* Update patch to match new file structure.
* Removed SD driver to be consistent with other MT7621 targets.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
SVN-Revision: 49213
John Crispin [Thu, 21 Apr 2016 19:47:02 +0000 (19:47 +0000)]
ramips: awake rt305x USB controller
Because of Ralink uboot set USB controller into sleep mode [1]
we check it and awake controller before any registers access.
Fix ticket #21396 [2]
[1] http://marc.info/?l=linux-usb&m=
137398626102108&w=2
[2] https://dev.openwrt.org/ticket/21396
Signed-Off-By: Serge Vasilugin <vasilugin@yandex.ru>
SVN-Revision: 49212
John Crispin [Thu, 21 Apr 2016 19:46:59 +0000 (19:46 +0000)]
ramips: add support for ELECOM WRH-300CR
ELECOM WRH-300CR is MT7620N based very small Wi-Fi router with 64MiB
DDR2 SDRAM, 16MiB SPI Flash, one fast ethernet port, and (internal but
easy-to-access) UART.
it also has internal USB hub and USB card reader which provide one USB
port, one SD card slot, and one microSD card slot.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
SVN-Revision: 49211
John Crispin [Thu, 21 Apr 2016 19:46:53 +0000 (19:46 +0000)]
lantiq: use new image build process for some images
This adds for some easy images the new build process.
This was only tested on some TP-Link devices, please test.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49210
John Crispin [Thu, 21 Apr 2016 19:46:49 +0000 (19:46 +0000)]
ramips: update DTS file for Planex DB-WRT01
update DTS files to use jedec,spi-nor compatible string for m25p80 to fix probe issues.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 49209
Rafał Miłecki [Wed, 20 Apr 2016 18:14:01 +0000 (18:14 +0000)]
bcm53xx: bump maximum TRX size for devices with serial flash
It was already increased for NAND devices so do the same for the ones
with serial memory.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 49207
John Crispin [Wed, 20 Apr 2016 17:19:08 +0000 (17:19 +0000)]
feeds.conf.default: remove the commented ancient feeds
Cleanup feeds.conf.default by removing the old commented-out feeds:
* x-wrt has not been updated for years and targets WhiteRussian/Kamikaze.
No currect code base available anywhere
* six old feeds from svn.openwrt.org/feeds. These feeds have not been
updated for 4-5 years and their code is currently unavailable
(in svn.openwrt.org)
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 49206
John Crispin [Wed, 20 Apr 2016 17:19:05 +0000 (17:19 +0000)]
ramips: fix support Planex MZK-750DHP.
fix script for Planex MZK-750DHP.
modification of the GPIO definition.
add Profile.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 49205
John Crispin [Wed, 20 Apr 2016 17:19:00 +0000 (17:19 +0000)]
ramips: rt3352 usbphy fix in dts-file
Add missing rt3352 usb phy. Fix ticket #20499.
Signed-Off-By:Serge Vasilugin <vasilugin@yandex.ru>
SVN-Revision: 49204
Hauke Mehrtens [Tue, 19 Apr 2016 20:18:50 +0000 (20:18 +0000)]
curl: remove file accidentally committed in r49197
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49199
Hauke Mehrtens [Tue, 19 Apr 2016 20:14:31 +0000 (20:14 +0000)]
oxnas: clean-up and improve profiles
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 49198
Hauke Mehrtens [Tue, 19 Apr 2016 20:12:41 +0000 (20:12 +0000)]
oxnas: add support for Akitio MyCloud mini
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 49197
Luka Perkov [Tue, 19 Apr 2016 13:46:33 +0000 (13:46 +0000)]
imx6: images: add bootfs.tar.gz build artifact
In order to create a bootable block storage device, both bootfs and rootfs
tarballs are required. However, our current scheme does not export a bootfs
tarball so add the packaging of it here.
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
SVN-Revision: 49196
Hauke Mehrtens [Sun, 17 Apr 2016 22:20:11 +0000 (22:20 +0000)]
ar71xx: add config ATH79_MACH_TL_WA901ND_V4 for kernel 4.4
This config option was not added in commit r49158.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49195
Hauke Mehrtens [Sun, 17 Apr 2016 22:03:58 +0000 (22:03 +0000)]
ar71xx: fix build error
This fixes a build error introduced in r49193.
This closes #22230
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49194
Hauke Mehrtens [Sun, 17 Apr 2016 19:10:13 +0000 (19:10 +0000)]
ar71xx: fix build with kernel 4.4
The file linux/mdio-gpio.h was moved to linux/platform_data/mdio-gpio.h
in kernel 4.4
Reported-by: Arjen de Korte <arjen+openwrt@de-korte.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49193
Hauke Mehrtens [Sun, 17 Apr 2016 15:35:18 +0000 (15:35 +0000)]
curl: fix deprecated 'depends' syntax
This was introduced in r49183
Reported-by: swalker
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49192
Hauke Mehrtens [Sun, 17 Apr 2016 15:16:12 +0000 (15:16 +0000)]
util-linux: update to version 2.28
The following patches were merged upstream:
* 0001-switch_root-improve-statfs-f_type-portability.patch
* 0002-lib-colors-use-static-buffers-when-parse-scheme.patch
* 002-mkostemp.patch
The following patch is not needed any more because all libc
implementations support alloc in sscanf:
* 001-no-printf-alloc.patch
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49191
Hauke Mehrtens [Sun, 17 Apr 2016 13:24:30 +0000 (13:24 +0000)]
x86: fix platform_export_bootpart() for Xen virtual disks
Virtual disk devices in a Xen virtual machine (DomU) can be /dev/xvda,
/dev/xvdb and so on with partitions like /dev/xdva1. Devices named like
this where not considered before. This resulted in a non working
sysupgrade, because the boot partition could not be found.
Signed-off-by: Alexander Dahl <alex@netz39.de>
Suggested-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49190
Hauke Mehrtens [Sun, 17 Apr 2016 12:53:31 +0000 (12:53 +0000)]
busybox: update to 1.24.2
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
[remove Kconfig changes]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49189
Hauke Mehrtens [Sun, 17 Apr 2016 12:53:11 +0000 (12:53 +0000)]
libnl-tiny: backport 'gnet_stats_rate_est64' support
This has been added to the kernel uapi for a while, and makes
sense to have it here too.
At the moment we're using it for query-ing qdisc via netlink
using libnl-tiny.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49188
Hauke Mehrtens [Sun, 17 Apr 2016 12:52:54 +0000 (12:52 +0000)]
dnsmasq: Add enable parameter in the UCI DHCP host section
Parameter allows to enable/disable static leases; by default the value is 1
to keep backwards compatibility
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49187
Hauke Mehrtens [Sun, 17 Apr 2016 12:52:37 +0000 (12:52 +0000)]
tools/cmake: update to 3.5.1
Update cmake to 3.5.1
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49186
Hauke Mehrtens [Sun, 17 Apr 2016 12:52:17 +0000 (12:52 +0000)]
tools/mpfr: update to 3.1.4
Update mpfr to 3.1.4
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49185
Hauke Mehrtens [Sun, 17 Apr 2016 12:51:57 +0000 (12:51 +0000)]
curl: add flags to allow gc-sections to strip out unused code
Signed-off-by: Dirk Feytons <dirk.feytons@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49184
Hauke Mehrtens [Sun, 17 Apr 2016 12:51:41 +0000 (12:51 +0000)]
curl: add config option for NTLM support
Signed-off-by: Dirk Feytons <dirk.feytons@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49183
Hauke Mehrtens [Sun, 17 Apr 2016 12:51:19 +0000 (12:51 +0000)]
curl: upstep to latest version 7.48.0
Signed-off-by: Dirk Feytons <dirk.feytons@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49182
Hauke Mehrtens [Sun, 17 Apr 2016 12:50:55 +0000 (12:50 +0000)]
hostapd.sh: Add support for "anonymous_identity" config field
The wpa_supplicant supports an "anonymous_identity" field, which some
EAP networks require. From the documentation:
anonymous_identity: Anonymous identity string for EAP (to be used as the
unencrypted identity with EAP types that support different tunnelled
identity, e.g., EAP-TTLS).
This change modifies the hostapd.sh script to propagate this field
from the UCI config to the wpa_supplicant.conf file.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Reviewed-by: Manuel Munz <freifunk@somakoma.de>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49181
Hauke Mehrtens [Sun, 17 Apr 2016 12:50:30 +0000 (12:50 +0000)]
package: remove .git files from images
If you have your ./files/ directory stored in a git repository,
the .git will be included into images using precious space.
This patch removes .git directories before packing images.
Signed-off-by: Joerg Jungermann <jj@borkum.net>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49180
Hauke Mehrtens [Sun, 17 Apr 2016 12:49:54 +0000 (12:49 +0000)]
base-files: allow to set arbitrary ip address and netmask
Signed-off-by: Roman Yeryomin <roman@advem.lv>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49179
Hauke Mehrtens [Sun, 17 Apr 2016 12:49:30 +0000 (12:49 +0000)]
toolchain/uClibc: enable UCLIBC_HAS_OBSOLETE_BSD_SIGNAL
This is required to build net-snmp.
If that options is disabled in uClibc then net-snmp doesn't
detect sighold support on its configuration stage and so
defines HAVE_SIGHOLD as 0. That in its turn causes compilation of
the following branch of timerPause() in apps/snmpnetstat:
------------------>8----------------
int oldmask;
oldmask = sigblock(sigmask(SIGALRM));
if (!signalled) {
sigpause(0);
}
sigsetmask(oldmask);
------------------>8----------------
Now in uClibc all 3 sigblock(), sigmask() and sigsetmask()
were removed back in 2005, see:
https://git.busybox.net/uClibc/commit/?id=
5aa7aa7fa7ec2a0fe567ac0b2595b46add6f3594
And all that causes net-snmp linkage to fail this way:
------------------>8----------------
.libs/if.o: In function `intpr':
if.c:(.text+0x908): undefined reference to `sigmask'
if.c:(.text+0x90e): undefined reference to `sigblock'
if.c:(.text+0x924): undefined reference to `sigsetmask'
------------------>8----------------
If we enable UCLIBC_HAS_OBSOLETE_BSD_SIGNAL in uClibc then
branch with sighold is used in timerPause() and everything builds as
expected.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49178
Hauke Mehrtens [Sat, 16 Apr 2016 21:05:48 +0000 (21:05 +0000)]
kernel: update kernel 4.4 to version 4.4.7
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49176
Hauke Mehrtens [Sat, 16 Apr 2016 20:06:34 +0000 (20:06 +0000)]
samba: fix some security problems
This fixes the following security problems:
* CVE-2015-7560
* CVE-2015-5370
* CVE-2016-2110
* CVE-2016-2111
* CVE-2016-2112
* CVE-2016-2115
* CVE-2016-2118
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49175
Rafał Miłecki [Sat, 16 Apr 2016 08:48:43 +0000 (08:48 +0000)]
mac80211: update brcmfmac including missing boardrev workaround
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 49174
Rafał Miłecki [Fri, 15 Apr 2016 10:11:44 +0000 (10:11 +0000)]
kernel: backport patch making bcm47xxsflash arch independent
This will be needed to use bcm47xxsflash on ARM for BCM53573.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 49168
Rafał Miłecki [Fri, 15 Apr 2016 10:11:31 +0000 (10:11 +0000)]
kernel: use upstream fixes for bgmac and BCM4709(4)
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 49167
Rafał Miłecki [Thu, 14 Apr 2016 05:54:20 +0000 (05:54 +0000)]
bcm53xx: backport BCM5301X earlycon and USB VCC patches
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 49166
Vasilis Tsiligiannis [Wed, 13 Apr 2016 20:52:26 +0000 (20:52 +0000)]
scripts/getver.sh: Use 'git-rev-parse' to detect if tree lies in Git repository
Path to the Git repository directory can be overriden by using the '$GIT_DIR'
environment variable. This patch improves detection of Git repository by using
'git-rev-parse', which respects '$GIT_DIR' environment variable, instead of just
checking the existence of '.git' directory.
Signed-off-by: Vasilis Tsiligiannis <acinonyx@openwrt.gr>
SVN-Revision: 49165
Vasilis Tsiligiannis [Wed, 13 Apr 2016 20:21:38 +0000 (20:21 +0000)]
include/cmake.mk: Add helper macro to handle conditionals for CMake boolean type variables
Signed-off-by: Vasilis Tsiligiannis <acinonyx@openwrt.gr>
SVN-Revision: 49164
Luka Perkov [Wed, 13 Apr 2016 07:33:24 +0000 (07:33 +0000)]
rpcd: update to latest version
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 49162
John Crispin [Sat, 9 Apr 2016 14:47:35 +0000 (14:47 +0000)]
ramips: remove accidentally comitted code
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 49161
Rafał Miłecki [Sat, 9 Apr 2016 13:23:25 +0000 (13:23 +0000)]
bcm53xx: add switch config workaround for R8500 and DIR-885L
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 49160
Rafał Miłecki [Sat, 9 Apr 2016 13:20:19 +0000 (13:20 +0000)]
bcm53xx: fix regression in generating network config
Syntax error was added in r49122.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 49159
John Crispin [Sat, 9 Apr 2016 10:26:46 +0000 (10:26 +0000)]
ar71xx: add TP-Link TL-WA901ND-v4 support
Signed-off-by: Tiziano Bacocco <tizbac2@gmail.com>
SVN-Revision: 49158
John Crispin [Sat, 9 Apr 2016 10:26:41 +0000 (10:26 +0000)]
ar71xx: add support for Compex WPJ342
OpenWrt can be flashed with following uboot commands:
tftpboot 0x80500000 openwrt-ar71xx-generic-wpj342-16M-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
SVN-Revision: 49157
John Crispin [Sat, 9 Apr 2016 10:26:37 +0000 (10:26 +0000)]
ar71xx: fix nondeterministic hangs during bootconsole/console handover
Reconfiguring the UART when the FIFO is not empty may cause the boot to
hang. This hang is extremely suspectible to timing differences; recompiling
the kernel with the same configuration, but different UTS_VERSION
timestamps can yield images that hang more or less often. Sometimes images
are produced that hang reproducibly.
This patch should also make it into one of the next linux-stable releases,
but it's better to get this fixed as soon as possible.
Fixes #21773, #21857.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 49156
John Crispin [Sat, 9 Apr 2016 10:26:34 +0000 (10:26 +0000)]
ar71xx: add OM5P-ACv2 to the OM5P-AC profile
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49155
John Crispin [Sat, 9 Apr 2016 10:26:31 +0000 (10:26 +0000)]
ar71xx: extract ath10k wifi board.bin for the OpenMesh OM5P-ACv2 board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49154
John Crispin [Sat, 9 Apr 2016 10:26:28 +0000 (10:26 +0000)]
uboot-envtools: add OpenMesh OM5P-ACv2 support
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49153
John Crispin [Sat, 9 Apr 2016 10:26:25 +0000 (10:26 +0000)]
om-watchdog: add OpenMesh OM5P-ACv2 support
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49152
John Crispin [Sat, 9 Apr 2016 10:26:22 +0000 (10:26 +0000)]
ar71xx: enable sysupgrade for the OpenMesh OM5P-ACv2
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49151
John Crispin [Sat, 9 Apr 2016 10:26:18 +0000 (10:26 +0000)]
ar71xx: add user-space support for the OpenMesh OM5P-ACv2
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49150
John Crispin [Sat, 9 Apr 2016 10:26:15 +0000 (10:26 +0000)]
ar71xx: add kernel support for the OpenMesh OM5P-ACv2 board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49149
John Crispin [Sat, 9 Apr 2016 10:26:11 +0000 (10:26 +0000)]
ar71xx: create profile and build image for the OpenMesh OM5P-AC board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49148
John Crispin [Sat, 9 Apr 2016 10:26:08 +0000 (10:26 +0000)]
ar71xx: extract ath10k wifi board.bin for the OpenMesh OM5P-AC board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49147
John Crispin [Sat, 9 Apr 2016 10:26:04 +0000 (10:26 +0000)]
uboot-envtools: add OpenMesh OM5P-AC support
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49146
John Crispin [Sat, 9 Apr 2016 10:26:01 +0000 (10:26 +0000)]
om-watchdog: add OpenMesh OM5P-AC support
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49145
John Crispin [Sat, 9 Apr 2016 10:25:57 +0000 (10:25 +0000)]
ar71xx: enable sysupgrade for the OpenMesh OM5P-AC
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49144
John Crispin [Sat, 9 Apr 2016 10:25:54 +0000 (10:25 +0000)]
scripts/om-fwupgradecfg-gen.sh: add support for the OM5P-AC
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49143
John Crispin [Sat, 9 Apr 2016 10:25:51 +0000 (10:25 +0000)]
ar71xx: add user-space support for the OpenMesh OM5P-AC
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49142
John Crispin [Sat, 9 Apr 2016 10:25:47 +0000 (10:25 +0000)]
ar71xx: add kernel support for the OpenMesh OM5P-AC board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49141
John Crispin [Sat, 9 Apr 2016 10:25:42 +0000 (10:25 +0000)]
scripts/om-fwupgradecfg-gen.sh: Generate sha256sum for uboot verification
Future Open Mesh u-boot versions are changing the check of the image files
(vmlinux, rootfs) from md5 to sha256. Having both in them should be enough
to ensure backward and forward compatibility.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49140
John Crispin [Sat, 9 Apr 2016 10:25:38 +0000 (10:25 +0000)]
brcmfmac43430-firmware: switch to @GITHUB download alias
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 49139
John Crispin [Sat, 9 Apr 2016 10:25:34 +0000 (10:25 +0000)]
download: add @GITHUB download facility
Define a new alias (@GITHUB) for downloading raw github repository files
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 49138
John Crispin [Sat, 9 Apr 2016 10:25:29 +0000 (10:25 +0000)]
lantiq-dsl: add missing blank in dsl output
blank inserted before ACTATP
Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
SVN-Revision: 49137
John Crispin [Sat, 9 Apr 2016 10:25:24 +0000 (10:25 +0000)]
lantiq-dsl: bugfix latency values swapped for lucistat
swapped wrong latency output
Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
SVN-Revision: 49136
John Crispin [Sat, 9 Apr 2016 10:25:20 +0000 (10:25 +0000)]
lantiq-dsl: bugfix db negative sign after comma
If db is negative minus sign was shown after comma
Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
SVN-Revision: 49135
John Crispin [Sat, 9 Apr 2016 10:25:16 +0000 (10:25 +0000)]
arc770: enable unaligned access handling simulation in software
This enables misaligned access handling by software in Linux kernel.
With some wireless drivers (ath9k-htc and mt7601u for example) we see
misaligned accesses here and there and to cope with that without
fixing stuff in the drivers we're just gracefully handling it on ARC.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
SVN-Revision: 49134
John Crispin [Sat, 9 Apr 2016 10:25:13 +0000 (10:25 +0000)]
arc770: build kmod-ath9k-htc wpad-mini by default
AXS101 beind a development board lacks built-in wireles inerfaces.
So we have to use external USB dongles to turn the board into
wireless router.
The best USB Wi-Fi dongles to work in AP-mode seem to be based on
ath9k-htc chipset.
And so with that change we add support of mentioned dongles in
default and axs101 builds.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
SVN-Revision: 49133
John Crispin [Sat, 9 Apr 2016 10:25:08 +0000 (10:25 +0000)]
mediatek: update patches
adds a few ethernet fixes
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 49132
John Crispin [Sat, 9 Apr 2016 10:25:03 +0000 (10:25 +0000)]
ramips: Disable the SD driver by default on MT7621
The SD driver has been a long and dragging issue on the MT7621 platforms as it hasn't worked for
months resulting in unbootable devices. Until it's fixed, disable it in the default profiles.
Reports / Discussed here:
https://dev.openwrt.org/ticket/21392
https://dev.openwrt.org/ticket/21834
https://dev.openwrt.org/ticket/21995
https://forum.openwrt.org/viewtopic.php?id=59092
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
SVN-Revision: 49131