85xx: Socrates: Major code update.

- Update the local bus ranges in the FDT for Linux for the various
  devices connected to the local bus via chip-select.

- Set the LCRR_DBYP bit in the LCRR for local bus frequencies
  lower than 66 MHz and uses I/O accessor functions consequently.

- UPM data update.

- Update of default environment and configuration.  Use I2C multibus
  as we do have two I2C buses.  Also enable sdram and ext2 commands.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
Signed-off-by: Detlev Zundel <dzu@denx.de>

Update Freescale 85xx boards to sys_eeprom.c

The new sys_eeprom.c supports both the old CCID EEPROM format and the new NXID
format, and so it obsoletes board/freescale/common/cds_eeprom.c.  Freescale
86xx boards already use sys_eeprom.c, so this patch migrates the remaining
Freescale 85xx boards to use it as well.  cds_eeprom.c is deleted.

Signed-off-by: Timur Tabi <timur@freescale.com>

Fix compiler warning in mpc8xxx ddr code

ctrl_regs.c: In function 'compute_fsl_memctl_config_regs':
ctrl_regs.c:523: warning: 'caslat' may be used uninitialized in this function
ctrl_regs.c:523: note: 'caslat' was declared here

Add a warning in DDR1 case if cas_latency isn't a value we know about.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

rtc: allow rtc_set to return an error and use it in cmd_date

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

ap325rxa/favr-32-ezkit: Use CONFIG_FLASH_CFI_DRIVER

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

config.mk: Move arch-specific condition to $(ARCH)_config.mk

Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>

Prevent crash if random/invalid ramdisks are passed to bootm

Adds returning an error from the ramdisk detection code if
its not a real ramdisk (invalid).  There is no reason we can't
just return back to the console if we detect an invalid
ramdisk or CRC error.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Prevent crash if random DTB address is passed to bootm

This patch adds bootm_start() return value check. If
error status is returned, we do not proceed further to
prevent board reset or crash as we still can recover
at this point.

Signed-off-by: Anatolij Gustschin <agust@denx.de>

clean up some #if !defined() in drivers/video/cfb_console.c

rearrange some #if !defined() / #else / #endif statements to remove
the negative logic.

Signed-off-by: Andrew Dyer <adyer@righthandtech.com>

apollon: use the last memory area for u-boot

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>

TQM8272: move NAND part in seperate File

I didn't try to use drivers/mtd/nand/fsl_upm.c for the NAND driver,
because I have no longer access to the hardware.

Signed-off-by: Heiko Schocher <hs@denx.de>

TQM8272: Fix compiling error for the TQM8272 board.

Fix compile problems caused by
commit  cfa460adfdefcc30d104e1a9ee44994ee349bb7b

Signed-off-by: Heiko Schocher <hs@denx.de>

Add JFFS2 command support on OneNAND

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>

Allow console input to be disabled

Added new CONFIG_DISABLE_CONSOLE define and GD_FLG_DISABLE_CONSOLE.

When CONFIG_DISABLE_CONSOLE is defined, setting
GD_FLG_DISABLE_CONSOLE disables all console input and output.

Signed-off-by: Mark Jackson <mpfj@mimc.co.uk>

loads: allow negative offsets

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>

USB EHCI: reset root hub

Some of multi-function USB controllers (e.g. ISP1562) allow root hub
resetting only via EHCI registers. So, this patch adds the
corresponding kind of reset to OHCI's hc_reset() if the newly
introduced CONFIG_PCI_EHCI_DEVNO option is set (e.g. for Socrates
board).

Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Acked-by: Markus Klotzbuecher <mk@denx.de>

RX 8025 RTC: analyze 12/24-hour mode flag in rtc_get().

Signed-off-by: Yuri Tikhonov <yur@emcraft.com>

devices: Use list_add_tail() instead of list_add() to register a device

This patch fixes a problem spotted on Glacier/Canyonlands (and most
likely lots of other board ports), that no serial output was seen
after console initialization in console_init_r(). This is because the
last added console device was used instead of the first added.

This patch fixes this problem by using list_add_tail() instead of
list_add() to register a device. This way the first added console
is used again.

Signed-off-by: Stefan Roese <sr@denx.de>

Merge branch 'master' of ssh://10.10.0.7/home/wd/git/u-boot/master

Merge branch 'master' of git://git.denx.de/u-boot-mpc83xx

mpc83xx: fix mpc8313 in-tree building with NAND

and add mpc8313 NAND build to MAKEALL

Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

Merge branch 'master' of ssh://10.10.0.7/home/wd/git/u-boot/master

mpc83xx: clean up cache operations and unlock_ram_in_cache() functions

Cleans up some latent issues with the data cache control so that
dcache_enable() and dcache_disable() will work reliably (after
unlock_ram_in_cache() has been called)

Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

mpc83xx: Store and display Arbiter Event Register values

Record the Arbiter Event Register values and optionally display them.

The Arbiter Event Register can record the type and effective address of
an arbiter error, even through an HRESET. This patch stores the values in
the global data structure.

Display of the Arbiter Event registers immediately after the RSR value
can be enabled with defines. The Arbiter values will only be displayed
if an arbiter event has occured since the last Power On Reset, and either
of the following defines exist:
 #define CONFIG_DISPLAY_AER_BRIEF - display only the arbiter address and
                                    and type register values
 #define CONFIG_DISPLAY_AER_FULL  - display and interpret the arbiter
                                    event register values

Address Only transactions are one of the trapped events that can register
as an arbiter event. They occur with some cache manipulation instructions
if the HID0_ABE (Address Broadcast Enable) is set and the memory region
has the MEMORY_COHERENCE WIMG bit set. Setting:
 #define CONFIG_MASK_AER_AO - prevents the arbiter from recording address
                              only events, so that it can still capture
                              other real problems.

Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

mpc83xx: use r4 instead of r2 in lock_ram_in_cache and unlock_ram_in_cache

This is needed in unlock_ram_in_cache() because it is called from C and
will corrupt the small data area anchor that is kept in R2.

lock_ram_in_cache() is modified similarly as good coding practice, but
is not called from C.

Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

MPC83XX: Fix GPIO configuration - set gpio level before direction

Set DAT value before DIR values to avoid creating glitches on the
GPIO signals.

Set gpio level register before direction register to inhibit
glitches on high level output pins.

Dir and data gets cleared at powerup, so high level output lines see
a short low pulse between setting the direction and level registers.

Issue was seen on a new board with the nReset line of the NOR flash
connected to a GPIO. Setting the direction register puts the NOR flash
in reset so the next instruction to set the level cannot get executed.

Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

Merge branch 'master' of git://git.denx.de/u-boot-mips

Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx

Conflicts:

board/esd/dasa_sim/dasa_sim.c

Signed-off-by: Wolfgang Denk <wd@denx.de>

Merge branch 'master' of git://git.denx.de/u-boot-net

doc/qemu_mips: add doc howto debug u-boot with gdb

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

ppx4xx: Fix broken DASA_SIM board

This patch adds initdram() to DASA_SIM boards that has been
removed accidentally by a previous commit.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>

ppc4xx: Remove reference to common/lists.o from some esd linker scripts

This patch removes some direct references to common/lists.o from some
esd linker scripts. This is necessary because the lists source was moved
and is not in the "common" directory anymore.

Signed-off-by: Stefan Roese <sr@denx.de>

ppc4xx: Remove obsolete or unused functions from some esd boards

This patch removes initdram() and testdram() from most esd 405 platforms.
Some boards also have an empty dummy implementation of
misc_init_f(). This is also removed.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>

ppc4xx: Update VOM405 board configuration

- remove PCI code
- add command line editing
- minor cleanup

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>

ppc4xx: Remove obsolete initdram() function from VOM405 board

This patch removed the obsolete initdram() function from
VOM405 platform file.

Some minor cleanup.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>

ppc4xx: Cleanup VOM405 linker script

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>

ppc4xx: Add fdt support for VOM405 boards

Signed-off-by: Matthias Fuchs <mf@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>

ppc4xx: Coding style cleanup

Wrap long lines etc.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>

ppc4xx: Enable USB on PLU405 boards

This patch enables the PCI-OHCI controller on PLU405 board.

Also the default CPU frequency is updated to 266 MHz and
command line editing is enabled.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>

ppc4xx: Cleanup PLU405 platform file

This patch
- wraps some long lines
- removes unused/obsolete functions: misc_init_f() and initdram()

Signed-off-by: Matthias Fuchs <mf@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>

ppc4xx: Cleanup PLU405 linker script

Signed-off-by: Matthias Fuchs <mf@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>

ppc4xx: Add fdt support for PLU405 boards

Signed-off-by: Matthias Fuchs <mf@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>

ppc4xx: Increase U-Boot size to 384kB for PLU405 boards

Signed-off-by: Matthias Fuchs <mf@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>

Don't tftp to unknown flash

If a board has a variable number of flash banks, there are empty entries
in flash_info[] and CFG_DIRECT_FLASH_TFTP is set, tftp boot fails with
"Outside available Flash". This patch skips flash banks with unknown
flash ids.

Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>

net: smc911x: Add pkt_data_pull and pkt_data_push function

The RSK7203 board has the SMSC9118 wired up 'incorrectly'.
Byte-swapping is necessary, and so poor performance is inevitable.
This problem cannot evade by the swap function of CHIP, this can
evade by software Byte-swapping.
And this has problem by FIFO access only. pkt_data_pull/pkt_data_push
functions necessary to solve this problem.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>

Moved initialization of EEPRO100 Ethernet controller to board_eth_init()

Affected boards:
db64360
db64460
katmai
taihu
taishan
yucca
cpc45
cpu87
eXalion
elppc
debris
kvme080
mpc8315erdb
integratorap
ixdp425
oxc
pm826
pm828
pm854
pm856
ppmc7xx
sc3
sc520_spunk
sorcery
tqm8272
tqm85xx
utx8245

Removed initialization of the driver from net/eth.c
Also, wrapped contents of pci_eth_init() by CONFIG_PCI.

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>

Moved initialization of TULIP Ethernet controller to board_eth_init()

Affected boards:
cu824
bab7xx
adciop
dasa_sim
mousse
mpc8540eval
musenki
mvblue
pcippc2/pcippc6
sbc8240
stxssa

Removed initialization of the driver from net/eth.c

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>

Moved initialization of E1000 Ethernet controller to board_eth_init()

Affected boards:
ap1000
mvbc_p
PM854

Removed initialization of the driver from net/eth.c

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>

Moved initialization of plb2800 Ethernet driver to board_eth_init

Affected boards:
purple

Removed initialization of controller from net/eth.c

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>

Moved initialization of MPC5xxx_FEC Ethernet driver to CPU directory

Modified board_eth_init() functions of boards that have this FEC in addition
to other Ethernet controllers.

Affected boards:
bc3450
icecube
mvbc_p
o2dnt
pm520
total5200
tq5200

Removed initialization of controller from net/eth.c

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>

Moved initialization of MPC512x_FEC Ethernet driver to CPU directory

Added a cpu_eth_init() function to MPC512x CPU directory and
removed code from net/eth.c

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>

Moved initialization of IncaIP Ethernet controller to board_eth_init

Affected boards:
IncaIP

Removed initialization of the driver from net/eth.c

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>

Moved initialization of 3COM Ethernet controller (AmigaOne) to board_eth_init()

    Affected boards:
        AmigaOneG3SE

    Removed initialization of the driver from net/eth.c

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>

Moved initialization of GT6426x Ethernet controller to board_eth_init()

Affected boards:
EVB64260
P3G4
ZUMA

Removed initialization of the driver from net/eth.c

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>

Moved initialization of PCNET Ethernet controller to board_eth_init()

Affected boards:
PN62
sc520_cdp

Removed initialization of the driver from net/eth.c

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>

Moved initialization of NATSEMI Ethernet controller to board_eth_init()

Affected boards:
a3000

Removed initialization of the driver from net/eth.c

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>

Moved initialization of NS8382X Ethernet controller to board_eth_init()

Affected boards:
bc3450
cpci5200
mecp5200
pf2000
icecube
o2dnt
pm520
sandpoint8245
total5200
tqm5200

Removed initialization of the driver from net/eth.c

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>

Moved initialization of TSI108 Ethernet controller to board_eth_init()

Affected boards:
mpc7448hpc2

Removed initialization of the driver from net/eth.c

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>

Moved initialization of RTL8139 Ethernet controller to board_eth_init()

Affected boards:
hidden_dragon
MPC8544DS
MPC8610HPCN
R2DPLUS
TB0229

Removed initialization of the driver from net/eth.c

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>

Moved initialization of RTL8169 Ethernet controller to board_eth_init()

Affected boards:
linkstation
r7780mp

Removed initialization of the driver from net/eth.c

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>

Moved initialization of Ethernet controllers on Atmel AT91 to board_eth_init()

Removed at91sam9_eth_initialize() from net/eth.c

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>

Introduce netdev.h header file and remove externs

This addresses all drivers whose initializers have already
been moved to board_eth_init()/cpu_eth_init().

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>

Add pixis_set_sgmii command

The 8544DS and 8572DS platforms support an optional SGMII riser card to
expose ethernet over an SGMII interface.  Once the card is in, it is also
necessary to configure the board such that it uses the card, rather than
the on-board ethernet ports.  This can either be done by flipping dip switches
on the motherboard, or by modifying registers in the pixis.  Either way
requires a reboot.

This adds a command to allow users to choose which ports are routed through
the SGMII card, and which through the onboard ports.  It also allows users
to revert to the current switch settings.

This code does not work on the 8572, as the PIXIS is different.

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>

Add SGMII support for the 8544 DS

The 8544 DS has an optional SGMII Riser card, which uses different PHY
addresses.  Check if we are in SGMII mode, and invoke the SGMII Riser
setup code if so.

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>

Add support for Freescale SGMII Riser Card

The 8544DS and 8572DS systems have an optional SGMII riser card which
exposes new ethernet ports which are connected to the eTSECs via an
SGMII interface.  The SGMII PHYs for this board are offset from the standard
PHY addresses, so this code modifies the passed in tsec_info structure to
use the SGMII PHYs on the card, instead.

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>

Add SGMII support to the tsec

Adds support for configuring the TBI to talk properly with the SerDes.

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>

Pass in tsec_info struct through tsec_initialize

The tsec driver contains a hard-coded array of configuration information
for the tsec ethernet controllers.  We create a default function that works
for most tsecs, and allow that to be overridden by board code.  It creates
an array of tsec_info structures, which are then parsed by the corresponding
driver instance to determine configuration.  Also, add regs, miiregs, and
devname fields to the tsec_info structure, so that we don't need the kludgy
"index" parameter.

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>

tsec: Move tsec.h to include/

This is to prepare the way for board code passing in the tsec_info structure

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>

PHY: Add support for the M88E1121R Marvell chip.

Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>

fw_env.c: fix build problems with MTD_VERSION=old

(as needed to support old 2.4 Linux kernel based releases)

Signed-off-by: Wolfgang Denk <wd@denx.de>

device: make device_register() clone the device

This is expected by the callers, but this fact was hidden well within
the old list implementation.

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Merge branch 'Makefile' of git://git.denx.de/u-boot-arm

Merge branch 'master' of git://git.denx.de/u-boot-arm

Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx

Merge branch 'master' of git://git.denx.de/u-boot-sh

Merge branch 'master' of git://git.denx.de/u-boot-mpc5xxx

sh: Remove CC line from board's Makefile

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

sh: Replaced "@./mkconfig" for @$(MKCONFIG)

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

sh: Add support sh2 to MAKEALL

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

sh: Fix compile error rsk7203 board

This boards used old type preprocessor.
This patch fix compile error.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

sh: Fix compile error sh7785lcr board

This boards used old type preprocessor.
This patch fix compile error.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

sh: Renesas Solutions AP325RXA board support

AP325RXA is SH7723's reference board.
This has SCIF, NOR Flash, Ethernet, USB host, LCDC, SD Host, Camera and other.
In this patch, support SCIF, NOR Flash, and Ethernet.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

sh: add support Renesas SH7723

Renesas SH7723 has 5 SCIF, SD, Camera, LCDC and other.
This patch supports CPU register's header file and SCIF serial driver.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

sh: Renesas RSK+ 7203 board support

This adds initial support for the RTE RSK+ SH7203 board.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

sh: Add support Renesas SH7203 processor

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

sh: Add support SH2/SH2A which is CPU of Renesas Technology

Add support SH2/SH2A basic function.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

sh: Renesas R0P7785LC0011RL board support

This board has SH7785, 512MB DDR2-SDRAM, NOR Flash,
Graphic, Ethernet, USB, SD, RTC, and I2C controller.

This patch supports the following functions:
 - 128MB DDR2-SDRAM (29-bit address mode only)
 - NOR Flash
 - USB host
 - Ethernet

Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

sh: add support for SH7785

Renesas SH7785 has DDR2-SDRAM controller, PCI, and other.
This patch supports CPU register's header file.

Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

davinci: fix remaining dm644x_eth

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

fs: Move conditional compilation to Makefile

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

devices: merge to list_head

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

update linux/list

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

smdk6400: add gitignore

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

smdk6400: Use CONFIG_FLASH_CFI_DRIVER

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

smdk6400: remove redundant bootargs definition

Double bootargs setting leads to a duplicated environmant entry.

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>

ARM: Add support for S3C6400 based SMDK6400 board

SMDK6400 can only boot U-Boot from NAND-flash. This patch adds a nand_spl
driver for it too. The board can also boot from the NOR flash, but due to
hardware limitations it can only address 64KiB on it, which is not enough
for U-Boot. Based on the original sources by Samsung for U-Boot 1.1.6.

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>

NAND: add NAND driver for S3C64XX

Based on the original S3C64XX NAND driver by Samsung for U-Boot 1.1.6.

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>

S3C64XX: remove broken HWFLOW support from the serial driver

As noted by Harald Welte, HWFLOW support in the S3C64XX serial driver is
broken and currently unused. Remove it.

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>

serial: add S3C64XX serial driver

Based on the original S3C64XX UART driver by Samsung for U-Boot 1.1.6.

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>

USB: Add support for OHCI controller on S3C6400

Notice: USB on S3C6400 currently works _only_ with switched off MMU. One could
try to enable the MMU, but map addresses 1-to-1, and disable data cache, then
it should work too and we could still profit from instruction cache.

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>