Herbert Xu [Tue, 26 May 2009 18:50:23 +0000 (18:50 +0000)]
gro: Only use skb_gro_header for completely non-linear packets
Currently skb_gro_header is used for packets which put the hardware
header in skb->data with the rest in frags. Since the drivers that
need this optimisation all provide completely non-linear packets,
we can gain extra optimisations by only performing the frag0
optimisation for completely non-linear packets.
In particular, we can simply test frag0 (instead of skb_headlen)
to see whether the optimisation is in force.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Tue, 26 May 2009 18:50:22 +0000 (18:50 +0000)]
gro: Localise offset/headlen in skb_gro_offset
This patch stores the offset/headlen in local variables as they're
used repeatedly in skb_gro_offset.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Tue, 26 May 2009 18:50:21 +0000 (18:50 +0000)]
gro: Inline skb_gro_header and cache frag0 virtual address
The function skb_gro_header is called four times per packet which
quickly adds up at 10Gb/s. This patch inlines it to allow better
optimisations.
Some architectures perform multiplication for page_address, which
is done by each skb_gro_header invocation. This patch caches that
value in skb->cb to avoid the unnecessary multiplications.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Tue, 26 May 2009 18:50:19 +0000 (18:50 +0000)]
gro: Open-code frags copy in skb_gro_receive
gcc does a poor job at generating code for the memcpy of the frags
array in skb_gro_receive, which is the primary purpose of that
function when merging frags. In particular, it can't utilise the
alignment information of the source and destination. This patch
open-codes the copy so we process words instead of bytes.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Peter P Waskiewicz Jr [Wed, 27 May 2009 04:41:18 +0000 (21:41 -0700)]
ixgbe: Fix build warning
This patch fixes a build warning due to an unused label.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 27 May 2009 04:16:25 +0000 (21:16 -0700)]
phy: Eliminate references to BUS_ID_SIZE.
Just use the constant 20 to keep things working.
If someone is so motivated, this can be converted over to
dynamic strings. I tried and it's a lot of work.
But for now this is good enough.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 27 May 2009 04:15:00 +0000 (21:15 -0700)]
nl80211: Eliminate reference to BUS_ID_SIZE.
It's going away. Just leave the constant "20" here so that
behavior doesn't change.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 27 May 2009 04:11:09 +0000 (21:11 -0700)]
sh_eth: Remove references to BUS_ID_SIZE, use MII_BUS_ID_SIZE instead.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 27 May 2009 04:10:22 +0000 (21:10 -0700)]
cpmac: Remove references to BUS_ID_SIZE, use MII_BUS_ID_SIZE.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 27 May 2009 04:09:33 +0000 (21:09 -0700)]
ixp4xx_eth: Remove references to BUS_ID_SIZE.
Use MII_BUS_ID_SIZE instead.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 27 May 2009 04:05:19 +0000 (21:05 -0700)]
net: Remove bogus reference to BUS_ID_SIZE in sysfs code.
BUS_ID_SIZE is really no more, and device names are dynamically
allocated and thus can be any necessary size.
So remove the BUG check here making sure BUS_ID_SIZE is at least
as large as IFNAMSIZ.
Signed-off-by: David S. Miller <davem@davemloft.net>
Jean Delvare [Wed, 27 May 2009 03:54:48 +0000 (20:54 -0700)]
r8169: Use a different default for each family
The r8169 driver supports 3 different families of network chips
(RTL8169, RTL8168 and RTL8101). When an unknown version is found, the
driver currently always defaults to the RTL8169 variant. This has very
little chance to ever work for chips of the other families. So better
define a per-family default.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kevin Hao [Wed, 27 May 2009 03:49:03 +0000 (20:49 -0700)]
net/ucc_geth: allow to set mac address on running device
Inspired by the patch for 8139too (
bda6a15a).
Currently we can't set mac address on a running ucc_geth device.
But this is needed when you use this device as a bonding slave in
bonding device in balance-alb mode. So add this feature for ucc_geth
device.
Signed-off-by: Kevin Hao <kexin.hao@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tanli Chang [Wed, 27 May 2009 03:45:50 +0000 (20:45 -0700)]
niu: Add support for C10NEM
This patch is for supporting C10NEM. C10NEM is a switch module, which
has back-to-back XAUI link connected to blades.
Signed-off-by: Tanli Chang <tanli.chang@sun.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don Skidmore [Wed, 27 May 2009 03:40:47 +0000 (20:40 -0700)]
ixgbe: fix 82598 SFP initialization after driver load.
If we loaded the driver with out a SFP module plugged in it would
leave it in a state that make it later unable to link when a module
was plugged in. This patch corrects that by:
ixgbe_probe() - moving the check for IXGBE_ERR_SFP_NOT_PRESENT from
after get_invariants() to after reset_hw() as now reset_hw() is
where this condition will be indentified.
ixgbe_reset_hw_82598() - Enable this function to now return
IXGBE_ERR_SFP_NOT_PRESENT.
ixgbe_identify_sfp_module_generic() - This where the lack of SFP
module is detected. Modifications are added to allow a different
return value for modules that just haven't been plugged in yet.
Other functions were updated to allow correct logging.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Peter P Waskiewicz Jr [Wed, 27 May 2009 03:40:09 +0000 (20:40 -0700)]
ixgbe: Remove device ID 0x10d8
Device ID 0x10d8 is the default silicon device ID for 82599. However, the
device will not be functional without an EEPROM, so we want to prevent the
driver from loading on the device. Otherwise, the driver will load, but no
PHY setup or PCIe setup will occur, causing the device to be unusable. To
prevent users from encountering this, just remove the device ID.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Tue, 26 May 2009 13:51:05 +0000 (13:51 +0000)]
igb/e1000e: update PSSR_MDIX value to reflect correct bit
The phy port status register has the MDI-X status bit on bit 11, not bit 3
as is currently setup in the define. This patch corrects that so the
correct bit is checked on igp PHY types.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesper Dangaard Brouer [Tue, 26 May 2009 13:50:48 +0000 (13:50 +0000)]
igb: Record host memory receive overflow in net_stats
Based on previous patch from Jesper Dangaard Brouer.
The RNBC (Receive No Buffers Count) register for the 82576, indicate
that frames were received when there were no available buffers in host
memory to store those frames (receive descriptor head and tail
pointers were equal). The packet is still received by the NIC if
there is space in the FIFO on the NIC.
As the RNBC value is not a packet drop, the driver stores this value
in net_stats.rx_fifo_errors to indicate that there were no system
buffers available for the incoming packet. Actual dropped packets
are counted in the MPC value.
Saving the stats in dev->net_stats makes it visible via
/proc/net/dev as "fifo", and thus viewable to ifconfig
as "overruns" and 'netstat -i' as "RX-OVR".
The Receive No Buffers Count (RNBC) can already be queried by
ethtool -S as "rx_no_buffer_count".
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesper Dangaard Brouer [Tue, 26 May 2009 13:50:31 +0000 (13:50 +0000)]
igb: Implement reading of reg RQDPC (Receive Queue Drop Packet Count)
Based on the previous patches from Jesper Dangaard Brouer <hawk@comx.dk>
Implement reading the per queue drop stats register
RQDPC (Receive Queue Drop Packet Count). It counts the number of
packets dropped by a queue due to lack of descriptors available.
Notice RQDPC (Receive Queue Drop Packet Count) stats only gets
incremented, if the DROP_EN bit it set (in the SRRCTL register
for that queue). If DROP_EN bit is NOT set, then the some what
equivalent count is stored in RNBC (not per queue basis).
The RQDPC register is only 12 bit, thus the precision might
suffer due to overrun in-netween the watchdog polling interval.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher [Tue, 26 May 2009 13:50:15 +0000 (13:50 +0000)]
igb: add RQDPC (Receive Queue Drop Packet Count) register macro
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Beregalov [Tue, 26 May 2009 12:35:27 +0000 (12:35 +0000)]
8139*: convert printk() to pr_<foo>()
Also convert DPRINTK to pr_debug and dev_printk to dev_<foo>.
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Beregalov [Tue, 26 May 2009 12:35:26 +0000 (12:35 +0000)]
3c5xx: convert printk() to pr_<foo>()
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Beregalov [Tue, 26 May 2009 12:35:25 +0000 (12:35 +0000)]
3c50x: convert printk() to pr_<foo>()
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 26 May 2009 06:48:43 +0000 (23:48 -0700)]
atl1: use netdev->stats
Get rid of private struct net_device_stats in "struct atl1e_adapter",
and use one provided in struct net_device instead.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 26 May 2009 05:58:01 +0000 (22:58 -0700)]
net: txq_trans_update() helper
We would like to get rid of netdev->trans_start = jiffies; that about all net
drivers have to use in their start_xmit() function, and use txq->trans_start
instead.
This can be done generically in core network, as suggested by David.
Some devices, (particularly loopback) dont need trans_start update, because
they dont have transmit watchdog. We could add a new device flag, or rely
on fact that txq->tran_start can be updated is txq->xmit_lock_owner is
different than -1. Use a helper function to hide our choice.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yoshihiro Shimoda [Sun, 24 May 2009 23:54:30 +0000 (23:54 +0000)]
net: sh_eth: Add support SH7724
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yoshihiro Shimoda [Sun, 24 May 2009 23:54:21 +0000 (23:54 +0000)]
net: sh_eth: CPU dependency code collect to "struct sh_eth_cpu_data"
This improves readability by collecting CPU dependency code.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yoshihiro Shimoda [Sun, 24 May 2009 23:53:40 +0000 (23:53 +0000)]
net: sh_eth: fix receive desciptor loop
Fix the problem that this driver not update rxdesc in sh_eth_rx.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yoshihiro Shimoda [Sun, 24 May 2009 23:53:20 +0000 (23:53 +0000)]
net: sh_eth: fix TX/RX descriptor not set physical memory
Fix the probrem that TX/RX descirptor not set physical memory.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yoshihiro Shimoda [Sun, 24 May 2009 23:52:35 +0000 (23:52 +0000)]
net: sh_eth: fix cache coherency issue
Fix the problem that may not work receive process by cache coherency issue.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jarek Poplawski [Tue, 26 May 2009 05:47:01 +0000 (22:47 -0700)]
pkt_sched: gen_estimator: Fix signed integers right-shifts.
Right-shifts of signed integers are implementation-defined so unportable.
With feedback from: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gabriel Paubert [Tue, 26 May 2009 05:46:19 +0000 (22:46 -0700)]
net: Remove obsolete MV64360 config option
Signed-off-by: Gabriel Paubert <paubert@iram.es>
Signed-off-by: David S. Miller <davem@davemloft.net>
Zhu Yi [Tue, 26 May 2009 05:41:51 +0000 (22:41 -0700)]
iwmc3200wifi: fix link error when CFG80211 is not selected
The patch makes iwmc3200wifi select CFG80211 instead of LIB80211.
This fixed module link error reported by Randy Dunlap
<randy.dunlap@oracle.com> when compiling iwmc3200wifi without
cfg80211 selected. WIRELESS_EXT is also selected by iwmc3200wifi.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Beregalov [Mon, 25 May 2009 08:53:53 +0000 (01:53 -0700)]
net: remove COMPAT_NET_DEV_OPS
All drivers are already converted to new net_device_ops API
and nobody uses old API anymore.
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 25 May 2009 08:42:21 +0000 (01:42 -0700)]
Merge branch 'master' of /linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/wireless/ath/ath5k/phy.c
drivers/net/wireless/iwlwifi/iwl-agn.c
drivers/net/wireless/iwlwifi/iwl3945-base.c
Andreas Eversberg [Mon, 25 May 2009 07:56:56 +0000 (00:56 -0700)]
mISDN: Added PCI ID for new Junghanns.net Single E1 cards.
The new ID is validated by Cologne Chip.
LEDs control is also supported.
Signed-off-by: Andreas Eversberg <andreas@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andreas Eversberg [Fri, 22 May 2009 11:04:58 +0000 (11:04 +0000)]
mISDN: Fix DTMF detection enable/disable
DTMF detection was enabled when it was not supposed to.
Signed-off-by: Andreas Eversberg <andreas@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnaldo Carvalho de Melo [Fri, 22 May 2009 11:04:57 +0000 (11:04 +0000)]
mISDN: Use kernel_{send,recv}msg instead of open coding
Reducing the number of direct users of sock_{recv,send}msg.
Modified version to match the latest context.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Karsten Keil [Fri, 22 May 2009 11:04:56 +0000 (11:04 +0000)]
mISDN: Cleanup debug messages
This patch make debug printk's KERN_DEBUG and also fix some
codestyle issues.
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andreas Eversberg [Fri, 22 May 2009 11:04:55 +0000 (11:04 +0000)]
mISDN: Add PCI ID for Junghanns 8S card
new id for HFC-8S
Signed-off-by: Andreas Eversberg <andreas@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roel Kluin [Fri, 22 May 2009 11:04:53 +0000 (11:04 +0000)]
mISDN: get_free_devid() failure ignored
dev->id is unsigned so a get_free_devid() error is ignored.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Karsten Keil [Fri, 22 May 2009 11:04:53 +0000 (11:04 +0000)]
mISDN: Add XHFC support for embedded Speech-Design board to hfcmulti
New version without emulating arch specific stuff for the other
architectures, the special IO and init functions for the 8xx
microcontroller are in a separate include file.
Signed-off-by: Andreas Eversberg <andreas@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Karsten Keil [Fri, 22 May 2009 11:04:52 +0000 (11:04 +0000)]
mISDN: Fix skb leak in error cases
If the channel receive function returns an error the skb must be freed.
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andreas Eversberg [Fri, 22 May 2009 11:04:51 +0000 (11:04 +0000)]
mISDN: Add "sapi" information to debug messages
Using sapi values other than 0 work now.
The "OpenBSC" project does not require special kernel patch anymore.
Signed-off-by: Andreas Eversberg <andreas@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Frank Seidel [Fri, 22 May 2009 11:04:51 +0000 (11:04 +0000)]
mISDN: Add allocation of recvbuf[1500] at run time to reduce stack size
Before: 1656 bytes on i386, now 164.
Modified by Andreas Eversberg <andreas@eversberg.eu>
Signed-off-by: Frank Seidel <frank@f-seidel.de>
Signed-off-by: Andreas Eversberg <andreas@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andreas Eversberg [Mon, 25 May 2009 07:50:02 +0000 (00:50 -0700)]
mISDN: Fix TEI and SAPI handling
Added SAPI value to use SAPIs different than 0.
Now fixed TEIs work in NT mode. This allows PTP endpoint to be connected
to PTMP ports together with other PTMP endpoints.
New enhanced version, thanks to Sam Ravnborg <sam@ravnborg.org> for the
hints.
Signed-off-by: Andreas Eversberg <andreas@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andreas Eversberg [Fri, 22 May 2009 11:04:49 +0000 (11:04 +0000)]
mISDN: Hardware acceleration is now possible in conjunction with audio recording
Audio recording requires software audio processing.
Both hardware and software processing is simultaniously possible now.
Signed-off-by: Andreas Eversberg <andreas@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andreas Eversberg [Fri, 22 May 2009 11:04:48 +0000 (11:04 +0000)]
mISDN: Fix DTMF locking bug issue
DTMF digits were sent up to socket in locked state.
Receive audio stream was not enabled in certain condition.
Signed-off-by: Andreas Eversberg <andreas@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andreas Eversberg [Fri, 22 May 2009 11:04:48 +0000 (11:04 +0000)]
mISDN: Added layer-1-hold feature
Add IMHOLD_L1 ioctl.
The feature will be disabled on closing.
Signed-off-by: Andreas Eversberg <andreas@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andreas Eversberg [Fri, 22 May 2009 11:04:47 +0000 (11:04 +0000)]
mISDN: Fixed missing spin lock on pipeline process
Need to protect the complete pipeline.
Signed-off-by: Andreas Eversberg <andreas@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Frank Seidel [Fri, 22 May 2009 11:04:47 +0000 (11:04 +0000)]
mISDN: Reduce stack size in dsp_cmx_send()
Reduce stack size memory footprint of mISDN_dsp.
(From 1468 bytes for dsp_cmx_send on i386 down to 44).
Signed-off-by: Frank Seidel <frank@f-seidel.de>
Signed-off-by: Andreas Eversberg <andreas@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andreas Eversberg [Fri, 22 May 2009 11:04:46 +0000 (11:04 +0000)]
mISDN: Echo canceler now gets delay information from hardware
Added tx-fifo information for calculation of current delay to sync tx and rx
streams for echo canceler.
Signed-off-by: Andreas Eversberg <andreas@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andreas Eversberg [Fri, 22 May 2009 11:04:45 +0000 (11:04 +0000)]
mISDN: DSP now uses ring buffer for echo canceler
DSP now uses ring buffer for echo canceler.
Added missing include in l1oip_codec.c
Signed-off-by: Andreas Eversberg <andreas@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andreas Eversberg [Fri, 22 May 2009 11:04:44 +0000 (11:04 +0000)]
mISDN: Add watchdog functionality to hfcmulti driver
This patch was made by Titus Moldovan and provides IOCTL functions for enabling
and disabling the controller's built in watchdog. The use is optional.
Signed-off-by: Andreas Eversberg <andreas@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lennert Buytenhek [Mon, 25 May 2009 07:42:34 +0000 (00:42 -0700)]
gianfar: fix BUG under load after introduction of skb recycling
Since commit
0fd56bb5be6455d0d42241e65aed057244665e5e ("gianfar:
Add support for skb recycling"), gianfar puts skbuffs that are in
the rx ring back onto the recycle list as-is in case there was a
receive error, but this breaks the following invariant: that all
skbuffs on the recycle list have skb->data = skb->head + NET_SKB_PAD.
The RXBUF_ALIGNMENT realignment done in gfar_new_skb() will be done
twice on skbuffs recycled in this way, causing there not to be enough
room in the skb anymore to receive a full packet, eventually leading
to an skb_over_panic from gfar_clean_rx_ring() -> skb_put().
Resetting the skb->data pointer to skb->head + NET_SKB_PAD before
putting the skb back onto the recycle list restores the mentioned
invariant, and should fix this issue.
Reported-by: Michael Guntsche <mike@it-loops.com>
Tested-by: Michael Guntsche <mike@it-loops.com>
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Fri, 22 May 2009 22:20:02 +0000 (22:20 +0000)]
skbuff: Copy csum instead of csum_start/csum_offset
Hi:
skbuff: Copy csum instead of csum_start/csum_offset
It's easier to copy the u32 csum instead of its two u16
constituents.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Cheers,
Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Fri, 22 May 2009 22:11:37 +0000 (22:11 +0000)]
skbuff: Move new code into __copy_skb_header
Hi:
skbuff: Move new __skb_clone code into __copy_skb_header
It seems that people just keep on adding stuff to __skb_clone
instead __copy_skb_header. This is wrong as it means your brand-new
attributes won't always get copied as you intended.
This patch moves them to the right place, and adds a comment to
prevent this from happening again.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Thanks,
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 25 May 2009 07:38:24 +0000 (00:38 -0700)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-next-2.6
Brice Goglin [Sun, 24 May 2009 05:27:59 +0000 (05:27 +0000)]
myri10ge: Add support for vlan_features
Add support for netdev->vlan_features in the myri10ge driver.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Brice Goglin [Sun, 24 May 2009 05:27:51 +0000 (05:27 +0000)]
myri10ge: drop myri10ge_lro module parameter
Drop the myri10ge_lro module parameter now that we have ethtool
to enable/disable LRO in the myri10ge driver.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Brice Goglin [Sun, 24 May 2009 05:27:41 +0000 (05:27 +0000)]
myri10ge: fix the invokation of lro_flush_all
Fix the way we check whether lro_flush_all should be called
in the myri10ge driver.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yevgeny Petrilin [Sun, 24 May 2009 03:17:11 +0000 (03:17 +0000)]
mlx4_en: Fix partial rings feature
In case of allocation failure, the actual ring size is rounded down to
nearest power of 2. The remaining descriptors are freed.
The CQ and SRQ are allocated with the actual size and the mask is updated.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yevgeny Petrilin [Sun, 24 May 2009 03:16:51 +0000 (03:16 +0000)]
mlx4_en: Removed redundant stride variable
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wey-Yi Guy [Fri, 22 May 2009 18:01:55 +0000 (11:01 -0700)]
iwlwifi: check for valid band for channel info
when display channel info in debugfs, always check for valid band
before access the pointer and display information
for 1000 NIC, it only support "bgn" mode, so there is no 5.2GHz channels
available to display.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohamed Abbas [Fri, 22 May 2009 18:01:54 +0000 (11:01 -0700)]
iwlagn: co-exist with AMT
Enable using iwlwifi driver in AMT system.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohamed Abbas [Fri, 22 May 2009 18:01:53 +0000 (11:01 -0700)]
iwlcore: Set rb_timeout to 0x10 for devices with ICT
rb value should be 0x10 for devices using ICT.
RX interrupt was not performing well with
0 value
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohamed Abbas [Fri, 22 May 2009 18:01:52 +0000 (11:01 -0700)]
iwlcore: Add support for periodic RX interrupt
Periodic RX interrupt needed with ICT interrupt to prevent RX race.
Sending RX interrupt require many steps to be done in the
the device:
1- write interrupt to current index in ICT table.
2- dma RX frame.
3- update RX shared data to indicate last write index.
4- send interrupt.
This could lead to RX race, driver could receive RX interrupt
but the shared data changes does not reflect that.
this could lead to RX race, RX periodic will solve this race
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohamed Abbas [Fri, 22 May 2009 18:01:51 +0000 (11:01 -0700)]
iwlcore: Allow skb allocation from tasklet.
If RX queue becomes empty then we need to restock the queue from tasklet to prevent
ucode from starving. A caller to iwl_rx_allocate will decide if allocated buffer should
come from GFP_ATOMIC or GFP_KERNEL.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohamed Abbas [Fri, 22 May 2009 18:01:50 +0000 (11:01 -0700)]
iwlcore: support ICT interrupt
Add ICT interrupt handler support, ICT should improve CPU utilization
since it does not require target read which is very expensive. This
interrupt handler only added to 5000 cards and newer. Device will write
interrupts to ICT shared table to inform driver about its interrupts.
These patches will not touch 3945 and 4965 interrupt handlers and tasklet.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 22 May 2009 18:01:49 +0000 (11:01 -0700)]
iwlwifi: support "pure 40MHz" in RXON command
Fix the bug when using 11n "pure 40MHz" mode cause uCode
crashing by adding support for "pure 40MHz" in RX_ON command flag.
the "mode" field (bits 25:26) has value of 0-3
0 = 20 MHz only
1 = 40MHz only
2 = Mixed
3 = Reserved
Control Channel ID (bit 22) is valid only in Mixed mode.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 22 May 2009 18:01:48 +0000 (11:01 -0700)]
iwlwifi: report the rate index as an MCS rate number
If transmit in HT rate, report the rate index as an MCS rate number
instead of an index. so "iw" can display correct BitRate
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohamed Abbas [Fri, 22 May 2009 18:01:47 +0000 (11:01 -0700)]
iwlcore: register locks
Add new lock to be used when accessing some registers. Also move
the register lock and iwl_grab_nic_access inside the function for register access. This
will prevent from forgetting to hold locks and nic access in the right way and make code
easier to maintain.
We over use the priv->lock spin lock and I guess we need to add new
one for Tx queue after that we might need to change most of these lock to
BH and just keep priv->lock as irq type.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 22 May 2009 18:01:46 +0000 (11:01 -0700)]
iwlwifi: support NVM access (EEPROM/OTP)
Two type of NVM available for devices 1000, 6000 and after, adding
support to read OTP lower blocks if OTP is used instead of EEPROM.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Thu, 21 May 2009 17:16:46 +0000 (19:16 +0200)]
rt2x00: Remove usage of IEEE80211_CONF_CHANGE_BEACON_INTERVAL
IEEE80211_CONF_CHANGE_BEACON_INTERVAL was deprecated a month ago,
it is about time to remove all usage from the rt2x00 drivers and
use the correct beacon interval configuration through the bss_info
structure.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Thu, 21 May 2009 17:16:14 +0000 (19:16 +0200)]
rt2x00: Add new rt2800usb USB ID's for Sweex
The USB ID with unknown manufacturer is apparently sweex,
copy it to the correct location of the list and add 2
additional USB ID's also belonging to Sweex.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jussi Kivilinna [Fri, 22 May 2009 14:40:34 +0000 (17:40 +0300)]
rndis_wlan: do not try to restore wpa keys using add_wep_key()
set_infra_mode() tried to restore wpa keys using add_wep_key(). This never
worked so prevent driver from trying.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jussi Kivilinna [Fri, 22 May 2009 14:40:27 +0000 (17:40 +0300)]
rndis_wlan: split add_wpa_key from rndis_iw_set_encode_ext
Split add_wpa_key() from rndis_iw_set_encode_ext so that conversion to cfg80211
would be easier later on.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jussi Kivilinna [Fri, 22 May 2009 14:40:20 +0000 (17:40 +0300)]
rndis_wlan: explain bits used in key setup code.
Driver uses some unnamed bits to control encryption setup. Move these to
enumerations with proper names explaining their meaning.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jussi Kivilinna [Fri, 22 May 2009 14:40:12 +0000 (17:40 +0300)]
rndis_wlan: remove CAP_SUPPORT_TXPOWER/OID_802_11_TX_POWER_LEVEL code
BCM4320 doesn't support OID_802_11_TX_POWER_LEVEL (chip implements
the command but setting value has no effect and getting txpower value
always returns 0xff, full power). So remove the code for cleanup.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jussi Kivilinna [Fri, 22 May 2009 08:58:36 +0000 (11:58 +0300)]
rndis_wlan: fix support for bcm4320a
Old variant of bcm4320 doesn't handle setting configuration parameters
correctly. One symptom is that MAC gets partially overwritten when any
config parameters are set. This patch disables config-params for bcm4320a
(and generic rndis-wlan).
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Thu, 21 May 2009 20:44:23 +0000 (13:44 -0700)]
iwlwifi: Temperature sensor voltage reading for 5150
The temperature measurement by uCode for 5150 and 5000 are different
CSR_HW_REV_TYPE_5150: temperature sensor output voltage
CSR_HW_REV_TYPE_5000: temperature in Celsius
temperature related operation for 5150 is measured by temperature sensor
output voltage; additional conversion is required for set and store
the temperature.
To make sure support different HW design; implement _ops method for
temperature related functions (temperature reading and set ct kill
threshold)
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Thu, 21 May 2009 20:44:22 +0000 (13:44 -0700)]
iwlwifi: add Greenfield support for 11n
Add "Greenfield" support for all devices except 4965 and
3945. "Greenfield" is part of 11n features to improve HT performance.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Abhijeet Kolekar [Thu, 21 May 2009 20:44:21 +0000 (13:44 -0700)]
iwl3945: improve 3945 leds
'tpt' is a delta throughput (number of packets) and is corelated
to brightness of the LED. We already maintain a delta of packets in
rxtxpackets. There is no need to calculate this delta again which
was affecting the behaviour of LEDS.
Also add two new callback functions for ASSOCIATED/DISASSOCIATED states
where LED's will be *on* for associated state and *off* for disassociated state.
This fixes
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1771.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bing Zhao [Thu, 21 May 2009 18:32:34 +0000 (11:32 -0700)]
libertas: read SD8688 firmware status from new register
The scratch pad register is used to store firmware status after
firmware is downloaded and initialized. After firmware status is
verified OK, the same register is used to store RX packet length.
Hence the firmware status code is no longer valid afterwards.
SD8688 firmware introduces a new register for firmware status
which will never be overwritten.
Also add scratch_reg variable to if_sdio_card structure and
initialize it based on the model of the card during probe.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Zhu Yi [Thu, 21 May 2009 13:20:45 +0000 (21:20 +0800)]
iwmc3200wifi: Add new Intel Wireless Multicomm 802.11 driver
This driver supports Intel's full MAC wireless multicomm 802.11 hardware.
Although the hardware is a 802.11agn device, we currently only support
802.11ag, in managed and ad-hoc mode (no AP mode for now).
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Zhu Yi [Thu, 21 May 2009 13:47:03 +0000 (21:47 +0800)]
wireless: move some utility functions from mac80211 to cfg80211
The patch moves some utility functions from mac80211 to cfg80211.
Because these functions are doing generic 802.11 operations so they
are not mac80211 specific. The moving allows some fullmac drivers
to be also benefit from these utility functions.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 21 May 2009 10:02:05 +0000 (12:02 +0200)]
mac80211: correct probe wait time
My first patch submission used 200ms, which I then somehow
managed to revert back to the earlier 50ms I had used for
some tests in the second patch submission -- but that was
wrong, I should have used 200ms here. Correct that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jouni Malinen [Wed, 20 May 2009 18:59:08 +0000 (21:59 +0300)]
ath9k: Update Beacon timers based on timestamp from the AP
Some APs seem to drift away from the expected TBTT (timestamp %
beacon_int_in_usec differs quite a bit from zero) which can result in
us waking up way too early to receive a Beacon frame. In order to work
around this, re-configure the Beacon timers after having received a
Beacon frame from the AP (i.e., when we know the offset between the
expected TBTT and the actual time the AP is sending out the Beacon
frame).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jouni Malinen [Wed, 20 May 2009 18:56:39 +0000 (21:56 +0300)]
ath9k: Optimize TBTT/DTIM calculation for timers
The previous version used a simple loop to go through all Beacon
frames when determining the next TBTT and DTIM count. This is not too
bad for the case where the setup happens before timesync (i.e., very
small TSF), but this can become very heavy operation if a short Beacon
interval is used and the current TSF is large.
In preparation for a patch to update timer setup based on Beacon
timestamp, optimize this routine to take fixed time regardless of the
actual TSF value.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bing Zhao [Wed, 20 May 2009 02:48:20 +0000 (19:48 -0700)]
libertas: implement function init/shutdown commands for SD8688
SD8688 is a WLAN/Bluetooth combo chip and both functions are supported
in a single firmware image. FUNC_INIT and FUNC_SHUTDOWN commands are
implemented to utilize the multiple function feature.
When SD8688 card is inserted, the firmware image should be downloaded
only once through either WLAN function (Libertas driver) or Bluetooth
function (Bluetooth driver).
This patch adds function init/shutdown for SD8688 WLAN function only.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bing Zhao [Wed, 20 May 2009 02:48:19 +0000 (19:48 -0700)]
libertas: get SD8688 rx length with one CMD52
Usually, the 16-bit rx length is read from scratch pad registers
with two CMD52 transactions:
SD8385: IF_SDIO_SCRATCH_OLD (0x80fe/0x80ff)
SD8686/SD8688: IF_SDIO_SCRATCH (0x34/0x35)
Alternatively, SD8688 firmware offers an enhanced method for driver
to read an 8-bit rx length (in units) with a single CMD52:
IF_SDIO_RX_UNIT 0x43 is read one time after firmware is ready.
IF_SDIO_RX_LEN 0x42 is read every time when rx interrupt is received.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bing Zhao [Wed, 20 May 2009 02:48:18 +0000 (19:48 -0700)]
libertas: define macros for SDIO model numbers
replace direct usages of SDIO model numbers with defined macros.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
andrey@cozybit.com [Wed, 20 May 2009 00:20:13 +0000 (17:20 -0700)]
libertas: fix GSPI card event handling
The GPSI interface driver does not re-enable the Card Event Interrupt, which
causes problems after a card event (for example: link-loss) comes in. This
can lead, for example, to the card failing to re-associate. This patch
ensures that we re-enable the Card Event Interrupt when we handle card events.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 19 May 2009 19:26:07 +0000 (21:26 +0200)]
mac80211: fix probe response wait timing
In "mac80211: split out and decrease probe wait time" I tried
to reduce the time waiting for a probe response, but failed to
take into account the case where we are detecting beacon loss
in software -- in that case we still wait the monitoring time
rather than the probe wait time. Fix this by refactoring the
mod_timer() calls in ieee80211_associated().
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 19 May 2009 15:19:36 +0000 (17:19 +0200)]
wext: remove atomic requirement for wireless stats
The requirement for wireless stats to be atomic is now mostly
artificial since we hold the rtnl _and_ the dev_base_lock for
iterating the device list. Doing that is not required, just the
rtnl is sufficient (and the rtnl is required for other reasons
outlined in commit "wext: fix get_wireless_stats locking").
This will fix http://bugzilla.kernel.org/show_bug.cgi?id=13344
and make things easier for drivers.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Herbert Xu [Fri, 22 May 2009 07:45:28 +0000 (00:45 -0700)]
tcp: Unexport TCPv6 GRO functions
Sinec the TCPv6 GRO functions are used in the same file where
they are defined, we do not need to export them. This was a
cut-n-paste from the IPv4 code which does need to export them.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 22 May 2009 06:30:09 +0000 (23:30 -0700)]
net: Fix arg to trace_napi_poll() in netpoll.
Reproted by Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Thu, 21 May 2009 13:07:12 +0000 (13:07 +0000)]
ixgbe: only register DCA requester once
The current driver tries to re-register the DCA requester after reset and
this is not correct. This change makes it so all we are doing is resetting
the DCA registers after reset and not re-adding the requester.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Thu, 21 May 2009 13:06:56 +0000 (13:06 +0000)]
igb: do not re-register DCA requester on device reset
The current driver is re-registering the DCA requester after every reset.
Instead of doing this we should only be updating the on board DCA registers
and not unregistering/re-registering our requester.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michał Mirosław [Thu, 21 May 2009 10:34:06 +0000 (10:34 +0000)]
wireless: Use genl_register_family_with_ops()
Use genl_register_family_with_ops() instead of a copy.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
projects / openwrt / staging / blogic.git / log