staging: wilc1000: Remove semaphore close_exit_sync

The semaphore 'close_exit_sync' does not serve any purpose other
than delaying the deregistration of the device which it is trying
to protect from shared access. 'up' is called only when a subdevice
is closed and not when it is opened. So, the semaphore count only
goes up when the device is used.

Signed-off-by: Binoy Jayan <binoy.jayan@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: wilc1000: Replace semaphore sync_event with completion

The semaphore 'sync_event' is used as completion, so convert
it to a struct completion type. Also, return -ETIME if the return
value of wait_for_completion_timeout is 0.

Signed-off-by: Binoy Jayan <binoy.jayan@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: wilc1000: Replace semaphore cfg_event with completion

The semaphore 'cfg_event' is used as completion, so convert
it to a struct completion type.

Signed-off-by: Binoy Jayan <binoy.jayan@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: wilc1000: Replace semaphore txq_add_to_head_cs with mutex

The semaphore 'txq_add_to_head_cs' is a simple mutex, so it should be
written as one. Semaphores are going away in the future. Also, removing
the timeout scenario as the error handling code does not propagate the
timeout properly.

Signed-off-by: Binoy Jayan <binoy.jayan@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: wilc1000: Replace semaphore txq_event with completion

The semaphore 'txq_event' is used as completion, so convert it
to a struct completion type.

Signed-off-by: Binoy Jayan <binoy.jayan@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: wilc1000: fix typo

firmare -> firmware

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: wilc1000: fix spelling mistake: "interupts" -> "interrupts"

trivial fix to spelling mistake in dev_err messages

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: wilc1000: remove unnecesary type cast of bss_type

There is no need to use type cast of bss_type because
hif_drv->cfg_values.bss_type is u8.

Signed-off-by: Chaehyun Lim <chaehyun.lim@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: wilc1000: add bss_type to remove line over 80 characters

A local bss_type variable is added to remove checkpatch warning of
line over 80 characters.

Signed-off-by: Chaehyun Lim <chaehyun.lim@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: wilc1000: remove unused struct set_mac_addr

struct set_mac_addr is not used anymore, so just remove it.

Signed-off-by: Chaehyun Lim <chaehyun.lim@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: wilc1000: rename result in handle_cfg_param

This patch renames result to ret that is used to get return value from
wilc_send_config_pkt. Some handle_*() functions are used as result,
others are used as ret. It will be changed as ret in all handle_*()
functions to match variable name.

Signed-off-by: Chaehyun Lim <chaehyun.lim@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: wilc1000: change data type of result in handle_cfg_param

This patch changes data type of result variable from s32 to int. result
is used to get return value from wilc_send_config_pkt that has return
type of int.

Signed-off-by: Chaehyun Lim <chaehyun.lim@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: wilc1000: change handle_cfg_param's return type to void

When handle_cfg_param is called in hostIFthread that is a kernel thread,
it is not checked return type of this function. This patch changes
return type to void.

Signed-off-by: Chaehyun Lim <chaehyun.lim@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: lustre: quiet lockdep recursive lock warning

Lockdep complains about potential recursive locking during mount
because the client configuration log is holding a lock on the MGC
obd_device to prevent it from being torn down, while also getting
mutexes on the MDC and OSC devices as they are instantiated:

 Lustre: Mounted myth-client
=============================================
[ INFO: possible recursive locking detected ]
4.7.0-rc2-vm-nfs+ #127 Tainted: G         C
---------------------------------------------

 May be due to missing lock nesting notation
2 locks held by ll_cfg_requeue/5928:
 #0:  (&cli->cl_sem){.+.+.+}, at: mgc_requeue_thread+0x15d/0x730 [mgc]
 #1:  (&cld->cld_lock){+.+.+.}, at: mgc_process_log+0x5e/0xf80 [mgc]
CPU: 0 PID: 5928 Comm: ll_cfg_requeue
Call Trace:
 [<ffffffff814a0855>] dump_stack+0x86/0xc1
 [<ffffffff810e7766>] __lock_acquire+0x726/0x1210
 [<ffffffff810e86be>] lock_acquire+0xfe/0x1f0
 [<ffffffff81888171>] down_read+0x51/0xa0
 [<ffffffffa04a8477>] sptlrpc_conf_client_adapt+0x47/0x150 [ptlrpc]
 [<ffffffffa0186b16>] mdc_set_info_async+0x2b6/0x470 [mdc]
 [<ffffffffa0294090>] class_notify_sptlrpc_conf+0x190/0x360 [obdclass]
 [<ffffffffa01a9e85>] mgc_process_log+0x925/0xf80 [mgc]
 [<ffffffffa01abafa>] mgc_requeue_thread+0x1fa/0x730 [mgc]
 [<ffffffff810af331>] kthread+0x101/0x120
 [<ffffffff8188ad6f>] ret_from_fork+0x1f/0x40

Add a separate lock class for the MGC callpath, since it will always
be held first, and none of the other obd_device locks should ever
be held concurrently.

Signed-off-by: Andreas Dilger <andreas.dilger@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/libcfs: Do not call kthread_run in wrong state

kthread_run might sleep during an allocation, and so
it's considered unsafe to call with a state that's not
RUNNABLE.
Move the state setting to after kthread_run call.

Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/osc: glimpse lock should match only with granted locks

A deadlock is possible during ccc_prep_size()->ldlm_lock_match() vs
cl_io_lock() which is waiting for a matched lock and conflicts with
already taken lock before ccc_prep_size().

It is better to send an additional lock request to avoid deadlock.

Seagate-bug-id: MRP-3312
Signed-off-by: Andriy Skulysh <andriy.skulysh@seagate.com>
Reviewed-on: http://review.whamcloud.com/18738
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-7829
Reviewed-by: Jinshan Xiong <jinshan.xiong@intel.com>
Reviewed-by: Bobi Jam <bobijam@hotmail.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre: Add documentation for unstable_stats in sysfs

commit ac5b14810952 ("staging: lustre: osc: Track and limit
"unstable" pages") added a new sysfs variable, but corresponding bit of
documentation was not forgotten.

Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/osc: fix signed one bit field

Bit field 'oi_lockless' and 'oi_is_active' has one bit and is signed
which is confusing.

Signed-off-by: Dmitry Eremin <dmitry.eremin@intel.com>
Reviewed-on: http://review.whamcloud.com/19196
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-7258
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: James Simmons <uja.ornl@yahoo.com>
Reviewed-by: Frank Zago <fzago@cray.com>
Reviewed-by: John L. Hammond <john.hammond@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/llite: IOC_MDC_GETFILEINFO returns the wrong ino

req_capsule_server_get() through  __req_capsule_get in ll_dir_ioctl()
returns a pointer to a PTLRPC request or reply buffer, which is assigned
to struct mdt_body.

If the command is IOC_MDS_GETFILEINFO then the inode "st.st_ino" should
be assigned from one extracted from mdt_body through cl_fid_build_ino().

Signed-off-by: John Hammond <john.hammond@intel.com>
Signed-off-by: akam kumar bharathi <azurelustre@gmail.com>
Reviewed-on: http://review.whamcloud.com/17618
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-5954
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/llite: ll_revalidate_dentry update

There are a couple of cases in ll_revalidate_dentry() where
we are pretty sure the dentry is valid, so check for them early
and save more expensive checks for later.

Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/llite: Restore proper opencache operations

Mark dentries that came to us via NFS in a special way so that
we can tell them apart during open and activate open cache
(we really don't want to do open/close RPC for every NFS IO).

This became needed since dentry revlidate no longer reimplements
any RPCs for lookup, and as such if a dentry is valid,
ll_revalidate_dentry returns 1 and ll_lookup_it() is never visited
during opens, we get straght into ll_file_open() without a valid
intent/RPC. This used to be only true for NFS, so opencache was
engaged needlessly, and it carries a cost of it's own if there is
in fact no repetitive file opening-closing going on

Signed-off-by: Oleg Drokin <oleg.drokin@intel.com>
Reviewed-on: http://review.whamcloud.com/20354
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-8019
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: Li Xi <lixi@ddn.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/llite: don't panic when fid is insane

LASSERT should never be done on data that is
received to over the network. Return EINVAL
when server returns invalid fid despite of
it_status == 0.

Signed-off-by: Sergey Cheremencev <sergey.cheremencev@seagate.com>
Seagate-bug-id: MRP-3073
Reviewed-on: http://review.whamcloud.com/17985
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-7422
Reviewed-by: John L. Hammond <john.hammond@intel.com>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/mdc: Zero atime in close RPC

While atime on close is supposed to only increase, there's
a bug in some older server versions where atime from a client
is taken no matter the value that allows a stale client atime
to overwrite a correct value.

Update atime in close rpc to 0 to help such servers out.

Signed-off-by: Niu Yawei <yawei.niu@intel.com>
Reviewed-on: http://review.whamcloud.com/19932
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-8041
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: Jinshan Xiong <jinshan.xiong@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/llite: ensure obd is effective in onu_upcall

The watched obd device may still not setup while onu_upcall
invoked. So we need verify it in cl_ocd_update.

Signed-off-by: Yang Sheng <yang.sheng@intel.com>
Reviewed-on: http://review.whamcloud.com/19597
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-8027
Reviewed-by: Niu Yawei <yawei.niu@intel.com>
Reviewed-by: Lai Siyao <lai.siyao@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/ldlm: const qualify struct lustre_handle * params

Add a const qualifier to several struct lustre_handle * parameters in
the LDLM interface.

Signed-off-by: John L. Hammond <john.hammond@intel.com>
Reviewed-on: http://review.whamcloud.com/17071
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-7403
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: James Simmons <uja.ornl@yahoo.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/llite: change it_data to it_request

Change the void *it_data member of struct lookup_intent to struct
ptlrpc_request *it_request.

Signed-off-by: John L. Hammond <john.hammond@intel.com>
Reviewed-on: http://review.whamcloud.com/17070
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-7403
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: James Simmons <uja.ornl@yahoo.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre: Inline Lustre intent disposition functions

They are just one-liners, so no point in having them exported
and called through a different module.

Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/llite: flatten struct lookup_intent

Replace the union in struct lookup_intent with the members of struct
lustre_indent_data. Remove the then unused struct lustre_intent_data.

Signed-off-by: John L. Hammond <john.hammond@intel.com>
Reviewed-on: http://review.whamcloud.com/17069
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-7403
Reviewed-by: James Simmons <uja.ornl@yahoo.com>
Reviewed-by: Dmitry Eremin <dmitry.eremin@intel.com>
Reviewed-by: Frank Zago <fzago@cray.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre: Add newline to LU_OBJECT_DEBUG() message

LU_OBJECT_DEBUG expects non \n terminated message from the caller,
so it should add it's own to keep debug logger happy.

Signed-off-by: Bob Glossman <bob.glossman@intel.com>
Reviewed-on: http://review.whamcloud.com/19960
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-8094
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: Alex Zhuravlev <alexey.zhuravlev@intel.com>
Reviewed-by: John L. Hammond <john.hammond@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre: LDLM_DEBUG() shouldn't be passed \n

as it adds own \n, so any extra \n break log format.

Signed-off-by: Alex Zhuravlev <alexey.zhuravlev@intel.com>
Reviewed-on: http://review.whamcloud.com/17494
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-7521
Reviewed-by: James Simmons <uja.ornl@yahoo.com>
Reviewed-by: John L. Hammond <john.hammond@intel.com>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/llite: take trunc_sem only at vvp layer

The lli_trunc_sem is taken in 'read' mode in both
ll_page_mkwrite and vvp_io_fault_start. This can lead to a
deadlock with another thread which asks for the semaphore
in write mode between thse two read calls.

Since all users of lli_trunc_sem are in the vvp layer, we
can satisfy the requirement to exclude truncate by taking
the semaphore only in vvp_io_fault_start.

Signed-off-by: Patrick Farrell <paf@cray.com>
Reviewed-on: http://review.whamcloud.com/19315
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-7981
Reviewed-by: Jinshan Xiong <jinshan.xiong@intel.com>
Reviewed-by: Andriy Skulysh <andriy.skulysh@seagate.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/ptlrpc: lost bulk leads to a hang

The reverse order of request_out_callback() and reply_in_callback()
puts the RPC into UNREGISTERING state, which is waiting for RPC &
bulk md unlink, whereas only RPC md unlink has been called so far.
If bulk is lost, even expired_set does not check for UNREGISTERING
state.

The same for write if server returns an error.

This phase is ambiguous, split to UNREG_RPC and UNREG_BULK.

Signed-off-by: Vitaly Fertman <vitaly.fertman@seagate.com>
Seagate-bug-id:  MRP-2953, MRP-3206
Reviewed-by: Andriy Skulysh <andriy.skulysh@seagate.com>
Reviewed-by: Alexey Leonidovich Lyashkov <alexey.lyashkov@seagate.com>
Tested-by: Elena V. Gryaznova <elena.gryaznova@seagate.com>
Reviewed-on: http://review.whamcloud.com/19953
Reviewed-by: Chris Horn <hornc@cray.com>
Reviewed-by: Ann Koehler <amk@cray.com>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/ptlrpc: Remove __ptlrpc_request_bufs_pack

Combine __ptlrpc_request_bufs_pack into ptlrpc_request_bufs_pack
because it was an unnecessary wrapper otherwise.

Signed-off-by: Ben Evans <bevans@cray.com>
Reviewed-on: http://review.whamcloud.com/16765
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-7269
Reviewed-by: Frank Zago <fzago@cray.com>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: John L. Hammond <john.hammond@intel.com>
Reviewed-by: Chris Horn <hornc@cray.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/ptlrpc: Early Reply vs Reply MDunlink

A race between unregister_reply & early reply.
When buffers are busy for the early transfer, they cannon be unlinked
by unregister_reply, so the RPC gets into UNREGISTERING state. The
coming reply_in_callback for the early RPC already has unlinked flag
set due to previous mdunlink attempt, but we handle it properly only
for UNILNK event, whereas this is PUT in this case.

Signed-off-by: Vitaly Fertman <vitaly.fertman@seagate.com>
Seagate-bug-id: MRP-3323
Reviewed-by: Alexey Leonidovich Lyashkov <alexey.lyashkov@seagate.com>
Reviewed-by: Andriy Skulysh <andriy.skulysh@seagate.com>
Tested-by: Parinay Vijayprakash Kondekar <parinay.kondekar@seagate.com>
Reviewed-on: http://review.whamcloud.com/18934
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-7434
Reviewed-by: Chris Horn <hornc@cray.com>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/ptlrpc: missing wakeup for ptlrpc_check_set

This patch changes a few things:

- There is no guarantee that request_out_callback will happen
  before reply_in_callback, if a request got reply and unlinked
  reply buffer before request_out_callback is called, then the
  thread waiting on ptlrpc_request_set will miss wakeup event.

  This may seriously impact performance of some IO workloads or
  result in RPC timeout

- To make code more easier to understand, this patch changes
  action-bits "rq_req_unlink" and "rq_reply_unlink" to
  status-bits "rq_req_unlinked" and "rq_reply_unlinked"

Signed-off-by: Liang Zhen <liang.zhen@intel.com>
Reviewed-on: http://review.whamcloud.com/12158
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-5696
Reviewed-by: Johann Lombardi <johann.lombardi@intel.com>
Reviewed-by: Li Wei <wei.g.li@intel.com>
Reviewed-by: Mike Pershin <mike.pershin@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/ptlrpc: reorganize ptlrpc_request

ptlrpc_request has some structure members are only for client side,
and some others are only for server side, this patch moved these
members to different structure then putting into an union.

By doing this, size of ptlrpc_request is decreased about 300 bytes,
besides saving memory, it also can reduce memory footprint while
processing.

Signed-off-by: Liang Zhen <liang.zhen@intel.com>
Reviewed-on: http://review.whamcloud.com/8806
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-181
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: Bobi Jam <bobijam@gmail.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/osc: Fix reverted condition in osc_lock_weight

When imprting clio simplification patch, the check for
pbject got reversed by mistake when converting from
if (obj == NULL) it somehow became (if (obj) which is obviously wrong,
and so when it does hit, a crash was happening as result.

Fix the condition and all if fine now.

Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/osc: osc_lock_weight endless loop fix

With huge number of pages to scan by osc_lock_weight() it is likely
CLP_GANG_RESCHED is returned from osc_page_gang_lookup() and the scan
will be repeated again from the start. To be sure that the scan is
progressing across those restarts, next scan should be started from
the last scanned page index plus one.

Xyratex-bug-id: MRP-2145
Signed-off-by: Alexander Zarochentsev <alexander.zarochentsev@seagate.com>
Signed-off-by: Jinshan Xiong <jinshan.xiong@intel.com>
Reviewed-on: http://review.whamcloud.com/12362
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-5781
Reviewed-by: Bobi Jam <bobijam@hotmail.com>
Reviewed-by: James Simmons <uja.ornl@gmail.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/llite: lock i_lock before __d_drop()

There has been several Lustre Client crashes reported by sites
running with Lustre versions 2.1/2.5, all showing the same
dentry->d_hash->next corrupted pointer cause.

This patch fixes a regression that has been introduced since a
long time by commit :
(LU-506 kernel: FC15 - support dcache scalability changes.)

where i_lock protection usage has been removed and
that is likely to cause racy condition during dentry [un]hashing
and to be the root cause of these crashes.

Signed-off-by: Bruno Faccini <bruno.faccini@intel.com>
Reviewed-on: http://review.whamcloud.com/19287
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-7973
Reviewed-by: Lai Siyao <lai.siyao@intel.com>
Reviewed-by: Yang Sheng <yang.sheng@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/llite: Get rid of ll_lock_dcache/ll_unlock_dcache

These are just doing spin_lock/unlock on inode's i_lock,
so just do the spinlock directly to make the code more clear

Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/llite: correct request handling after ll_lookup_it()

In the FIFO cases of ll_atomic_open() and ll_lookup_nd() remove
spurious calls to ptlrpc_req_finished(). Explain that these cases are
unreachable in practice anyway.

Signed-off-by: John L. Hammond <john.hammond@intel.com>
Reviewed-on: http://review.whamcloud.com/17068
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-7402
Reviewed-by: Dmitry Eremin <dmitry.eremin@intel.com>
Reviewed-by: Lai Siyao <lai.siyao@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre/llite: allocate and free client cache asynchronously

Since the inflight request holds import refcount as well as export,
sometimes obd_disconnect() in client_common_put_super() can't put
the last refcount of OSC import (e.g. due to network disconnection),
this will cause cl_cache being accessed after free.

To fix this issue, ccc_users is used as cl_cache refcount, and
lov/llite/osc all hold one cl_cache refcount respectively, to avoid
the race that a new OST is being added into the system when the client
is mounted.
The following cl_cache functions are added:
- cl_cache_init(): allocate and initialize cl_cache
- cl_cache_incref(): increase cl_cache refcount
- cl_cache_decref(): decrease cl_cache refcount and free the cache
  if refcount=0.

Signed-off-by: Emoly Liu <emoly.liu@intel.com>
Reviewed-on: http://review.whamcloud.com/13746
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-6173
Reviewed-by: Niu Yawei <yawei.niu@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: lustre: remove remote client support

There are several obsolete sub commands for lfs to work with
remote client. We do not support that anymore, and should be
deleted along with any kernel code related to remote client.

Signed-off-by: Fan Yong <fan.yong@intel.com>
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-6971
Reviewed-on: http://review.whamcloud.com/19789
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: James Simmons <uja.ornl@yahoo.com>
Reviewed-by: Lai Siyao <lai.siyao@intel.com>
Reviewed-by: Oleg Drokin <oleg.drokin@intel.com>
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge 4.7-rc4 into staging-next

We want the fixes in here, and we can resolve a merge issue in
drivers/iio/industrialio-trigger.c

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 4.7-rc4

Merge branch 'for_linus' of git://git./linux/kernel/git/jack/linux-fs

Pull UDF fixes and a reiserfs fix from Jan Kara:
 "A couple of udf fixes (most notably a bug in parsing UDF partitions
  which led to inability to mount recent Windows installation media) and
  a reiserfs fix for handling kstrdup failure"

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
  reiserfs: check kstrdup failure
  udf: Use correct partition reference number for metadata
  udf: Use IS_ERR when loading metadata mirror file entry
  udf: Don't BUG on missing metadata partition descriptor

Merge tag 'dmaengine-fix-4.7-rc4' of git://git.infradead.org/users/vkoul/slave-dma

Pull dmaengine fixes from Vinod Koul:
 "Some fixes has piled up, so time to send them upstream.

  These fixes include:
   - at_xdmac fixes for residue and other stuff
   - update MAINTAINERS for dma dt bindings
   - mv_xor fix for incorrect offset"

* tag 'dmaengine-fix-4.7-rc4' of git://git.infradead.org/users/vkoul/slave-dma:
  dmaengine: mv_xor: Fix incorrect offset in dma_map_page()
  dmaengine: at_xdmac: double FIFO flush needed to compute residue
  dmaengine: at_xdmac: fix residue corruption
  dmaengine: at_xdmac: align descriptors on 64 bits
  MAINTAINERS: Add file patterns for dma device tree bindings

Merge tag 'armsoc-fixes' of git://git./linux/kernel/git/arm/arm-soc

Pull ARM SoC fixes from Olof Johansson:
 "Another batch of fixes for ARM SoC platforms.  Most are smaller fixes.

  Two areas that are worth pointing out are:

   - OMAP had a handful of changes to voltage specs that caused a bit of
     churn, most of volume of change in this branch is due to this.

   - There are a couple of _rcuidle fixes from Paul that touch common
     code and came in through the OMAP tree since they were the ones who
     saw the problems.

 The rest is smaller changes across a handful of platforms"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (36 commits)
  ARM: dts: STi: stih407-family: Disable reserved-memory co-processor nodes
  ARM: dts: am437x-sk-evm: Reduce i2c0 bus speed for tps65218
  ARM: OMAP2+: timer: add probe for clocksources
  ARM: OMAP1: fix ams-delta FIQ handler to work with sparse IRQ
  memory: omap-gpmc: Fix omap gpmc EXTRADELAY timing
  arm: Use _rcuidle for smp_cross_call() tracepoints
  MAINTAINERS: Add myself as reviewer of ARM FSL/NXP
  ARM: OMAP: DRA7: powerdomain data: Remove unused pwrsts_mem_ret
  ARM: OMAP: DRA7: powerdomain data: Remove unused pwrsts_logic_ret
  ARM: OMAP: DRA7: powerdomain data: Set L3init and L4per to ON
  ARM: imx6ul: Fix Micrel PHY mask
  ARM: OMAP2+: Select OMAP_INTERCONNECT for SOC_AM43XX
  ARM: dts: DRA74x: fix DSS PLL2 addresses
  ARM: OMAP2: Enable Errata 430973 for OMAP3
  ARM: dts: socfpga: Add missing PHY phandle
  ARM: dts: exynos: Fix port nodes names for Exynos5420 Peach Pit board
  ARM: dts: exynos: Fix port nodes names for Exynos5250 Snow board
  ARM: dts: sun6i: yones-toptech-bs1078-v2: Drop constraints on dc1sw regulator
  ARM: dts: sun6i: primo81: Drop constraints on dc1sw regulator
  ARM: dts: sunxi: Add OLinuXino Lime2 eMMC to the Makefile
  ...

Merge tag 'gpmc-omap-fixes-for-v4.7' of https://github.com/rogerq/linux into fixes

OMAP-GPMC: Fixes for for v4.7-rc cycle:

- Fix omap gpmc EXTRADELAY timing. The DT provided timings
were wrongly used causing devices requiring extra delay timing
to fail.

* tag 'gpmc-omap-fixes-for-v4.7' of https://github.com/rogerq/linux:
  memory: omap-gpmc: Fix omap gpmc EXTRADELAY timing
  + Linux 4.7-rc3

Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'omap-for-v4.7/fixes-powedomain' of git://git./linux/kernel/git/tmlind/linux-omap into fixes

Fixes for omaps for v4.7-rc cycle:

- Fix dra7 for hardware issues limiting L4Per and L3init power domains
  to on state. Without this the devices may not work correctly after
  some time of use because of asymmetric aging. And related to this,
  let's also remove the unusable states.

- Always select omap interconnect for am43x as otherwise the am43x
  only configurations will not boot properly. This can happen easily
  for any product kernels that leave out other SoCs to save memory.

- Fix DSS PLL2 addresses that have gone unused for now

- Select erratum 430973 for omap3, this is now safe to do and can
  save quite a bit of debugging time for people who may have left
  it out.

* tag 'omap-for-v4.7/fixes-powedomain' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP: DRA7: powerdomain data: Remove unused pwrsts_mem_ret
  ARM: OMAP: DRA7: powerdomain data: Remove unused pwrsts_logic_ret
  ARM: OMAP: DRA7: powerdomain data: Set L3init and L4per to ON
  ARM: OMAP2+: Select OMAP_INTERCONNECT for SOC_AM43XX
  ARM: dts: DRA74x: fix DSS PLL2 addresses
  ARM: OMAP2: Enable Errata 430973 for OMAP3
  + Linux 4.7-rc2

Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'fixes-rcu-fiq-signed' of git://git./linux/kernel/git/tmlind/linux-omap into fixes

Fixes for omaps for v4.7-rc cycle:

- Two boot warning fixes from the RCU tree that should have gotten
  merged several weeks ago already but did not because of issues
  with who merges them. Paul has now split the RCU warning fixes into
  sets for various maintainers.

- Fix ams-delta FIQ regression caused by omap1 sparse IRQ changes

- Fix PM for omap3 boards using timer12 and gptimer, like the
  original beagleboard

- Fix hangs on am437x-sk-evm by lowering the I2C bus speed

* tag 'fixes-rcu-fiq-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: am437x-sk-evm: Reduce i2c0 bus speed for tps65218
  ARM: OMAP2+: timer: add probe for clocksources
  ARM: OMAP1: fix ams-delta FIQ handler to work with sparse IRQ
  arm: Use _rcuidle for smp_cross_call() tracepoints
  arm: Use _rcuidle tracepoint to allow use from idle

Signed-off-by: Olof Johansson <olof@lixom.net>

ARM: dts: STi: stih407-family: Disable reserved-memory co-processor nodes

This patch fixes a non-booting issue in Mainline.

When booting with a compressed kernel, we need to be careful how we
populate memory close to DDR start.  AUTO_ZRELADDR is enabled by default
in multi-arch enabled configurations, which place some restrictions on
where the kernel is placed and where it will be uncompressed to on boot.

AUTO_ZRELADDR takes the decompressor code's start address and masks out
the bottom 28 bits to obtain an address to uncompress the kernel to
(thus a load address of 0x42000000 means that the kernel will be
uncompressed to 0x40000000 i.e. DDR START on this platform).

Even changing the load address to after the co-processor's shared memory
won't render a booting platform, since the AUTO_ZRELADDR algorithm still
ensures the kernel is uncompressed into memory shared with the first
co-processor (0x40000000).

Another option would be to move loading to 0x4A000000, since this will
mean the decompressor will decompress the kernel to 0x48000000. However,
this would mean a large chunk (0x44000000 => 0x48000000 (64MB)) of
memory would essentially be wasted for no good reason.

Until we can work with ST to find a suitable memory location to
relocate co-processor shared memory, let's disable the shared memory
nodes.  This will ensure a working platform in the mean time.

NB: The more observant of you will notice that we're leaving the DMU
shared memory node enabled; this is because a) it is the only one in
active use at the time of this writing and b) it is not affected by
the current default behaviour which is causing issues.

Fixes: fe135c6 (ARM: dts: STiH407: Move over to using the 'reserved-memory' API for obtaining DMA memory)
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'imx-fixes-4.7' of git://git./linux/kernel/git/shawnguo/linux into fixes

The i.MX fixes for 4.7:
 - Correct Micrel PHY mask to fix the issue that i.MX6UL ethernet works
   in U-Boot but not in kernel.

* tag 'imx-fixes-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  ARM: imx6ul: Fix Micrel PHY mask

Signed-off-by: Olof Johansson <olof@lixom.net>

staging/lustre: Update FID documentation link.

When OpenSFS took over lustre.org, there was some reshuffling.
FIDs on ZFS document is now at
http://wiki.old.lustre.org/index.php/Architecture_-_Interoperability_fids_zfs
instead of the old location, so update comments accordingly.

Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Reported-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre: Remove unnecessary space after a cast

This patch fixes all checkpatch occurences of
"CHECK: No space is necessary after a cast"
in Lustre code.

Signed-off-by: Emoly Liu <emoly.liu@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre: Keep logical continuations on the previous line

This patch fixes all checkpatch occurences of
"CHECK: Logical continuations should be on the previous line"
in Lustre code.

Signed-off-by: Emoly Liu <emoly.liu@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/lustre: Fix blank line before EXPORT_SYMBOL()

This patch fixes one checkpatch warning in lustre:
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable

Signed-off-by: Emoly Liu <emoly.liu@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtl8192u: Remove unused semaphore rf_sem

The semaphore 'rf_sem' in rtl8192u has no users, hence removing it.

Signed-off-by: Binoy Jayan <binoy.jayan@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtl8192u: Replace semaphore scan_sem with mutex

The semaphore 'scan_sem' in rtl8192u is a simple mutex, so it should
be written as one. Semaphores are going away in the future.

Signed-off-by: Binoy Jayan <binoy.jayan@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtl8192u: ieee80211_device: Replace semaphore wx_sem with mutex

The semaphore 'wx_sem' in ieee80211_device is a simple mutex,
so it should be written as one. Semaphores are going away in the future.

Signed-off-by: Binoy Jayan <binoy.jayan@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtl8192u: r8192_priv: Replace semaphore wx_sem with mutex

The semaphore 'wx_sem' in r8192_priv is a simple mutex, so
it should be written as one. Semaphores are going away in the future.

Signed-off-by: Binoy Jayan <binoy.jayan@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8192u: propagate errors in write_nic_dword

Propagate errors from kzalloc and usb_control_msg and change the
return type of write_nic_dword from void to int.

Signed-off-by: Salah Triki <salah.triki@acm.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8192u: propagate errors in write_nic_word

Propagate errors from kzalloc and usb_control_msg and change the
return type of write_nic_word from void to int.

Signed-off-by: Salah Triki <salah.triki@acm.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8192u: propagate errors in write_nic_byte_E

Propagate errors from  kzalloc and usb_control_msg and change the
return type of write_nic_byte_E from void to int.

Signed-off-by: Salah Triki <salah.triki@acm.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8192u: propagate errors in write_nic_byte

Propagate errors from  kzalloc and usb_control_msg and change the
return type of write_nic_byte from void to int.

Signed-off-by: Salah Triki <salah.triki@acm.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8192u: check return value of rtl8192_read_eeprom_info

The call of rtl8192_read_eeprom_info may fail, therefore its return
value must be checked and propagated in the case of error

Signed-off-by: Salah Triki <salah.triki@acm.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8192u: propagate errors in rtl8192_read_eeprom_info

Propagate error from eprom_read and change the return type of
rtl8192_read_eeprom_info from void to int.

Signed-off-by: Salah Triki <salah.triki@acm.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8192u: check return value eprom_read

The call of eprom_read may fail, therefore its return value must be
checked

Signed-off-by: Salah Triki <salah.triki@acm.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8192u: propagate errors in eprom_read

Propagate error from eprom_r and change the return type of eprom_read
from u32 to int.

Signed-off-by: Salah Triki <salah.triki@acm.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8192u: check return value of read_nic_word_E

The call of read_nic_word_E may fail, therefore its return value must be
checked and propagated in the case of error.

Signed-off-by: Salah Triki <salah.triki@acm.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: ks7010: remove bogus NULL checks

enc->rx_seq[] and enc->key[] are arrays, not pointers and they can't be
NULL.  Let's remove these NULL checks.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: ks7010: drop private handler for driver version

We are upstream now, we don't need seperate driver versioning.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: ks7010: report interface as wlan not eth

Until we switch to cfg80211 (if ever), we must do this manually.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: ks7010: bail out when registering netdevice fails

There is no need to continue then. Also, this enables us to remove an
ugly static variable.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: ks7010: sdio: remove forward declarations

Move read/write functions to the top and driver struct to the end, so we
can remove all forward declarations.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: ks7010: unify naming to ks7010

No 79xx anymore, this is confusing. Add a comment saying that old
versions were probably named 7910/79xx.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: ks7010: export sdio ids

So the module will be loaded automatically on card insertion. Rename the
array while here.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: ks7010: collect all includes and sort them

Includes probably need a driver-wide clean up, but for now let's at
least group all includes from the sdio file together.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: ks7010: function declaration should be in a header file

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: ks7010: remove cfg file handling

I verified that all but two settings from the config file can be set up
also via 'iwconfig' or 'iwpriv'. The two missing are ROM_FILE and
PhyInformationTimer. ROM_FILE can be easily dropped. There is only one
known firmware floating on the net, so, the name is fix and we can make
this constant. Frankly, I don't know when PhyInformationTimer needs to
be set to non-zero. But if we need it somewhen, there is already
(currently commented out) code to add this as another private method, so
we could use that. Summa summarum: We can remove the config file
handling and the example config file. The only useful action,
initialization of the configuration struct, is now moved to the sdio
main file.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge branch 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm

Pull ARM fixes from Russell King:
 "A couple of fixes for pmd_mknotpresent()/pmd_present() for LPAE
  systems"

* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
  ARM: 8579/1: mm: Fix definition of pmd_mknotpresent
  ARM: 8578/1: mm: ensure pmd_present only checks the valid bit

Merge tag 'usb-4.7-rc4' of git://git./linux/kernel/git/gregkh/usb

Pull USB fixes from Greg KH:
 "Here are a bunch (65) of USB fixes for 4.7-rc4.  Sorry about the
  quantity, I've been slow in getting these out.

  The majority are the "normal" gadget, musb, and xhci fixes, that we
  all are used to.  There are also a few other tiny fixes resolving a
  number of reported issues that showed up in 4.7-rc1.

  All of these have been in linux-next"

* tag 'usb-4.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (65 commits)
  usbip: rate limit get_frame_number message
  usb: musb: sunxi: Remove bogus "Frees glue" comment
  usb: musb: sunxi: Fix NULL ptr deref when gadget is registered before musb
  usb: echi-hcd: Add ehci_setup check before echi_shutdown
  usb: host: ehci-msm: Conditionally call ehci suspend/resume
  MAINTAINERS: Add file patterns for usb device tree bindings
  usb: host: ehci-tegra: Avoid getting the same reset twice
  usb: host: ehci-tegra: Grab the correct UTMI pads reset
  USB: mos7720: delete parport
  USB: OHCI: Don't mark EDs as ED_OPER if scheduling fails
  phy: ti-pipe3: Program the DPLL even if it was already locked
  usb: musb: Stop bulk endpoint while queue is rotated
  usb: musb: Ensure rx reinit occurs for shared_fifo endpoints
  usb: musb: host: correct cppi dma channel for isoch transfer
  usb: musb: only restore devctl when session was set in backup
  usb: phy: Check initial state for twl6030
  usb: musb: Use normal module_init for 2430 glue
  usb: musb: Remove pm_runtime_set_irq_safe
  usb: musb: Remove extra PM runtime calls from 2430 glue layer
  usb: musb: Return error value from musb_mailbox
  ...

Merge tag 'staging-4.7-rc4' of git://git./linux/kernel/git/gregkh/staging

Pull IIO and staging fixes from Greg KH:
 "Here are a number of IIO and staging bugfixes for 4.7-rc4.

  Nothing huge, the normal amount of iio driver fixes, and some small
  staging driver bugfixes for some reported problems (2 are reverts of
  patches that went into 4.7-rc1).  All have been in linux-next with no
  reported issues"

* tag 'staging-4.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (24 commits)
  Revert "Staging: rtl8188eu: rtw_efuse: Use sizeof type *pointer instead of sizeof type."
  Revert "Staging: drivers: rtl8188eu: use sizeof(*ptr) instead of sizeof(struct)"
  staging: lustre: lnet: Don't access NULL NI on failure path
  iio: hudmidity: hdc100x: fix incorrect shifting and scaling
  iio: light apds9960: Add the missing dev.parent
  iio: Fix error handling in iio_trigger_attach_poll_func
  iio: st_sensors: Disable DRDY at init time
  iio: st_sensors: Init trigger before irq request
  iio: st_sensors: switch to a threaded interrupt
  iio: light: bh1780: assign a static name
  iio: bh1780: dereference the client properly
  iio: humidity: hdc100x: fix IIO_TEMP channel reporting
  iio:st_pressure: fix sampling gains (bring inline with ABI)
  iio: proximity: as3935: fix buffer stack trashing
  iio: proximity: as3935: remove triggered buffer processing
  iio: proximity: as3935: correct IIO_CHAN_INFO_RAW output
  max44000: Remove scale from proximity
  iio: humidity: am2315: Remove a stray unlock
  iio: humidity: hdc100x: correct humidity integration time mask
  iio: pressure: bmp280: fix error message for wrong chip id
  ...

Merge tag 'driver-core-4.7-rc4' of git://git./linux/kernel/git/gregkh/driver-core

Pull driver core fixes from Greg KH:
 "Here are a small number of debugfs, ISA, and one driver core fix for
  4.7-rc4.

  All of these resolve reported issues.  The ISA ones have spent the
  least amount of time in linux-next, sorry about that, I didn't realize
  they were regressions that needed to get in now (thanks to Thorsten
  for the prodding!) but they do all pass the 0-day bot tests.  The
  others have been in linux-next for a while now.

  Full details about them are in the shortlog below"

* tag 'driver-core-4.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  isa: Dummy isa_register_driver should return error code
  isa: Call isa_bus_init before dependent ISA bus drivers register
  watchdog: ebc-c384_wdt: Allow build for X86_64
  iio: stx104: Allow build for X86_64
  gpio: Allow PC/104 devices on X86_64
  isa: Allow ISA-style drivers on modern systems
  base: make module_create_drivers_dir race-free
  debugfs: open_proxy_open(): avoid double fops release
  debugfs: full_proxy_open(): free proxy on ->open() failure
  kernel/kcov: unproxify debugfs file's fops

Merge tag 'char-misc-4.7-rc4' of git://git./linux/kernel/git/gregkh/char-misc

Pull char/misc driver fixes from Greg KH:
 "Here are a small number of char and misc driver fixes for 4.7-rc4.

  They resolve some minor issues that have been reported, and have all
  been in linux-next"

* tag 'char-misc-4.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  coresight: Handle build path error
  coresight: Fix erroneous memset in tmc_read_unprepare_etr
  coresight: Fix tmc_read_unprepare_etr
  coresight: Fix NULL pointer dereference in _coresight_build_path
  extcon: palmas: Fix boot up state of VBUS when using GPIO detection
  mcb: Acquire reference to carrier module in core
  mcb: Acquire reference to device in probe
  mei: don't use wake_up_interruptible for wr_ctrl

Merge branch 'for-linus-4.7' of git://git./linux/kernel/git/mason/linux-btrfs

Pull btrfs fixes from Chris Mason:
 "The most user visible change here is a fix for our recent superblock
  validation checks that were causing problems on non-4k pagesized
  systems"

* 'for-linus-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: btrfs_check_super_valid: Allow 4096 as stripesize
  btrfs: remove build fixup for qgroup_account_snapshot
  btrfs: use new error message helper in qgroup_account_snapshot
  btrfs: avoid blocking open_ctree from cleaner_kthread
  Btrfs: don't BUG_ON() in btrfs_orphan_add
  btrfs: account for non-CoW'd blocks in btrfs_abort_transaction
  Btrfs: check if extent buffer is aligned to sectorsize
  btrfs: Use correct format specifier

Merge tag 'acpi-4.7-rc4' of git://git./linux/kernel/git/rafael/linux-pm

Pull ACPI fix from Rafael Wysocki:
 "Revert a recent ACPICA commit that introduced a suspend-to-RAM
  regression on one system due to incorrect information in its ACPI
  tables that had not been taken into consideration at all before (and
  everything worked), but the commit in question started to use it"

* tag 'acpi-4.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  Revert "ACPICA: ACPI 2.0, Hardware: Add access_width/bit_offset support for acpi_hw_write()"

Merge tag 'pm-4.7-rc4' of git://git./linux/kernel/git/rafael/linux-pm

Pull power management fixes from Rafael Wysocki:
 "Fixes for two recent regressions that may lead to degraded performance
  (operating performance points framework, intel_pstate).

  Specifics:

   - Fix a recent regression in the intel_pstate driver that may lead to
     degraded performance on some systems due to missing turbo state
     entry in the table returned by the ACPI _PSS object (Srinivas
     Pandruvada).

   - Fix a recent regression in the OPP (operating performance points)
     framework that may lead to degraded performance on some systems
     where the OPP table is created too early (Viresh Kumar)"

* tag 'pm-4.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  PM / OPP: Add 'UNKNOWN' status for shared_opp in struct opp_table
  cpufreq: intel_pstate: Adjust _PSS[0] freqeuency if needed

Merge branch 'for-linus' of git://git./linux/kernel/git/jikos/hid

Pull HID subsystem fixes from Jiri Kosina:

 - kernel panic fix in hid-elo from Oliver Neukum

 - Surface Pro 3 device quirk from Benjamin Tissoires

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: multitouch: Add MT_QUIRK_NOT_SEEN_MEANS_UP to Surface Pro 3
  HID: elo: kill not flush the work

staging/android: sync_debug: unproxify debugfs files' fops

Since commit 49d200deaa68 ("debugfs: prevent access to removed files'
private data"), a debugfs file's file_operations methods get proxied
through lifetime aware wrappers.

However, only a certain subset of the file_operations members is supported
by debugfs and ->compat_ioctl isn't among them -- it appears to be NULL
from the VFS layer's perspective.

This behaviour breaks the /sys/kernel/debug/sync/sw_sync file introduced
concurrently with commit a44eb74cd413 ("staging/android: move SW_SYNC_USER
to a debugfs file").

Since that file never gets removed, there is no file removal race and thus,
a lifetime checking proxy isn't needed.

Avoid the proxying for /sys/kernel/debug/sync/sw_sync by creating it via
debugfs_create_file_unsafe() rather than debugfs_create_file().
For consistency, do the same for /sys/kernel/debug/sync/info.

Fixes: 49d200deaa68 ("debugfs: prevent access to removed files' private data")
Fixes: a44eb74cd413 ("staging/android: move SW_SYNC_USER to a debugfs file")
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/android: add DEBUG_FS dependence on Kconfig

SW_SYNC only works with DEBUG_FS so state it in the Kconfig file.

Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/android: rename sync.h to sync_debug.h

This header file only contains information for debugging and SW_SYNC, so
rename it to sync_debug.h instead of having a more generic name.

Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/android: remove drv_name from sync_timeline

As it is internal to sw_sync now this value will always be "sw_sync".

Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/android: remove sync_timeline_destroy()

This function was just used by the file release function, so we just fold
its content there and remove sync_timeline_destroy().

Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/android: remove 'destroyed' member from struct sync_timeline

'destroyed' was set but not used ny anyone.

Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/android: make sw_ioctl info internal to sw_sync.c

We don't want to export this from the kernel. This is interface is only
for testing and debug. So testers shall copy the ioctl info in their own
projects.

Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/android: make sync_timeline internal to sw_sync

The only use sync_timeline will have in upstream kernel is for debugging
through the SW_SYNC interface. So make it internal to SW_SYNC to avoid
people use it in the future.

Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/android: clean up #includes in the sync framework

Most of the includes there are not necessary anymore.

Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/android: move sw_sync related code to sw_sync.c

Split sync_debug and sw_sync in two different files.

Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging/android: bring struct sync_pt back

Move the list_head members from sync_pt to struct fence was a mistake,
they will not be used by struct fence as planned before, so here we create
sync_pt again to bring the list heads back.

Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>