staging: comedi: s626: remove the "interrupt call test"

This commented out code in s626_ai_insn_read() is just left over
development test code. Remove it.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: s626: async commands require an interrupt

Only hook up the analog input command support if the interrupt is
available.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: s626: remove the ai (*insn_config) function

This subdevice function is not implemented in the driver. Just
remove it.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: s626: cleanup subdevice init

For aesthetic reasons, add some whitespace to the subdevice init.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: s626: remove subdevice pointer math

Convert the comedi_subdevice access from pointer match to array
access.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: s626: cleanup s626_dio_insn_bits()

Add some local variables to make this function a bit clearer and
remove the unnecessary comments.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: s626: cleanup s626_dio_insn_config()

Add some local variables to make this function a bit cleaner.

The comedi core expects this function to return the number of
data parameters used. Change the return from '1' to insn->n to
make this more aparent.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: s626: remove the uint16_t casts of the bit values

There are a number of uint16_t casts used in the #define's of the
constant bit field values as well as the calls to DEBIreplace().
These cause a number of sparse warnings of the type:

warning: cast truncates bits from constant value (ffff1cff becomes 1cff)

Remove all of the casts and change the types of the parameters to
DEBIreplace from uin16_t to unsigned int. This fixes all the warnings.

Mask the addr that is or'ed with DEBI_CMD_RDWORD then written to the
P_DEBICMD register as well as the val written to the P_DEBIAD register
with 0xffff. The addr and val are only 16-bits but the registers are
32-bits.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: s626: rename private data 'base_addr' variable

The base_address variable in the private data is the ioremap'ed
PCI bar 0 resource.

For aesthetic reasons, and to shorten some of the lines, rename
this variable to 'mmio'.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: s626: remove RR7146 macro

This macro relies on a local variable having a specific name its
also just a wrapper around a readl() call. Remove the macro and
just call readl() directly.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: s626: remove WR7146 and SETVECT macros

The WR7146 macro relies on a local variable having a specific name.
This macro is a wrapper around a writel() call. Remove the macro and
just call writel() directly.

The SETVEC macro uses the WR7146 macro so remove it as well and just
do the writel() directly.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: s626: remove MC_TEST macro

This macro relies on a local variable having a specific name. Replace
it with a new helper function, s626_mc_test().

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: xgifb: rename SR15/SR13 arrays to SR18

Since we are programming SR register 18, better name structs/arrays
accordingly to avoid confusion.

Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: xgifb: make SR15/SR13 arrays single dimensional

Since we only access the third row, we can delete the others.

Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: xgifb: XGINew_SetDRAMDefaultRegister340: inline the value of SR1B

SR1B register value is always 3 regardless of video card or RAM type.

Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: xgifb: delete pXGINew_DRAMTypeDefinition

Delete unused struct field.

Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: xgifb: delete XGI330_LCDCapStruct.PWD_2x

Delete unused XGI330_LCDCapStruct fields.

Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: xgifb: delete XGI330_LCDCapStruct.PSC_Sx

Delete unused XGI330_LCDCapStruct fields.

Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: xgifb: delete LCD_SetFlag

Delete redundant XGI330_LCDCapStruct field.

Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: xgifb: delete IF_DEF_TRUMPION and IF_DEF_DSTN

Delete some unused flags.

Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: xgifb: eliminate IF_DEF_LVDS checks from vb_init

Inside vb_init, IF_DEF_LVDS tells only if the vbios was succesfully read
on XG21. Rearrange the code so that we don't need to set or care about
this flag.

Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: xgifb: delete redundant IF_DEF_LVDS check

IF_DEF_LVDS can be set only on XG21.

Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: zsmalloc: Fix link error on ARM

Testing the arm chromebook config against the upstream
kernel produces a linker error for the zsmalloc module from
staging. The symbol flush_tlb_kernel_range is not available
there. Fix this by removing the reimplementation of
unmap_kernel_range in the zsmalloc module and using the
function directly. The unmap_kernel_range function is not
usable by modules, so also disallow building the driver as a
module for now.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8192u: fix coding style

Fix coding style of r8192U_dm.h

Signed-off-by: Haksu Jeong <hsjeong@snu.ac.kr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: vt6656: remove consecutive newlines

Several sed -i '/^$/{ N /^\n$/ D }' drivers/staging/vt6656/*.[ch]

Signed-off-by: Andres More <more.andres@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: sep: Fix typo in printk within sep driver

Correct spelling typo in printk.

Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/staging/zcache/zcache-main.c: fix build

flush_dcache_page() takes a page*, not a void*.  It breaks ia64.

Remove this and another unused function.  Warnings remain:

drivers/staging/zcache/zcache-main.c: In function '__check_disable_cleancache':
drivers/staging/zcache/zcache-main.c:1837: warning: return from incompatible pointer type
drivers/staging/zcache/zcache-main.c: In function '__check_disable_frontswap':
drivers/staging/zcache/zcache-main.c:1838: warning: return from incompatible pointer type
drivers/staging/zcache/zcache-main.c: In function '__check_disable_frontswap_ignore_nonactive':
drivers/staging/zcache/zcache-main.c:1842: warning: return from incompatible pointer type

Cc: Dan Magenheimer <dan.magenheimer@oracle.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: fix labpc_calib_insn_write()

The comedi core expects the (*insn_write) operations to write insn->n
values and return the number of values actually wrote.

Make this function work like the core expects.

As Ian Abbott pointed out for the eeprom writes, we really only need
to write the last value to the caldac. The preceding data would be
overwritten anyway.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: fix labpc_calib_insn_read()

The comedi core expects the (*insn_read) operations to read insn->n
values and return the number of values actually read.

Make this function work like the core expects.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: simplify labpc_range_is_unipolar()

As Ian Abbott pointed out, this helper function can be simplified
by just checking if the 'min' value is >= 0.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: fix labpc_eeprom_insn_write()

The comedi core expects the (*insn_write) operations to write insn->n
values and return the number of values actually wrote.

Make this function work like the core expects.

As Ian Abbott pointed out, we really only need to write the last value
to the eeprom. The preceding data would be overwritten anyway.

Also, remove the noise about invalid channels.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: vt6656: remove unused functions

Removed defined symbols not being used elsewhere.
Only compile tested.

Signed-off-by: Andres More <more.andres@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: davinci: Fix typo in staging/media/davinci

Correct spelling typo in staging/media/davinci

Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: wlan-ng: prism2usb.c: fix printk(KERN_ERR... to dev_err(dev, ...

Fix checkpatch warning. Change printk(KERN_ERR ... to dev_err(dev ...

Signed-off-by: Nick Østergaard <oe.nick@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: dwc2: fix wrong setting of DMA masks

We were setting the DMA masks in dwc2_driver_probe(), but that is
before the driver parameters have been set to their default values.
That meant the DMA masks could be set wrong. Fix it by moving the
DMA mask setting into dwc2_hcd_init(), after the driver parameters
have been set.

Reported-by: Matthijs Kooijman <matthijs@stdin.nl>
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: dwc2: remove unneeded arguments from two functions

Remove the unneeded struct device *dev argument from dwc2_hcd_init()
and dwc2_hcd_remove(), and pass in the value through the hsotg->dev
member instead

Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: dwc2: always release host channel after dequeueing

Previously, when an active urb was dequeued, its host channel would
not always be released. There is some special handling for this in
dwc2_hc_chhltd_intr_dma, but when it was the last urb/qtd in its qh, a
safeguard in dwc2_hc_n_intr would short-circuit and prevent the regular
interrupt handlers from running, without releasing the channel.

This is easily triggered when using a 3G modem using the option driver.
Opening and closing any ttyUSBx device will eat up a host channel that
is forever unusable from that point on.

Signed-off-by: Matthijs Kooijman <matthijs@stdin.nl>
[paulz@synopsys.com: fixed comment style and added a couple of NULL checks]
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: vt6656: Fix stuck in scanning with variable uScanChannel.

When pMgmt->uScanChannel > pDevice->byMaxChannel scanning ends
but no SIOCGIWSCAN(scan done) message is sent. This section of code is
duplicate of that in WLAN_CMD_SCAN_END which sends scan done.
So remove it and jump eCommandState to WLAN_CMD_SCAN_END.

Increment uScanChannel on !ChannelValid.

At WLAN_CMD_SCAN_END reset uScanChannel to 0 when done.

Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: s626: remove MC_DISABLE macro

This macro relies on a local variable having a specific name. Replace
it with a new helper function, s626_mc_disable().

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: s626: remove MC_ENABLE macro

This macro relies on a local variable having a specific name. Replace
it with a new helper function, s626_mc_enable().

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: s626: #ifdef out a block of unused code

Currently the unused s626_ai_rinsn() function is commented out with
/* ... */ on every line of the function. Remove those by using an

This block will be removed once it is determined that it really
is not needed.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: s626: cleanup comedi_lrange table

Reformat the whitespace in the comedi_lrange table and use the
BIP_RANGE() macro instead of generic RANGE() macro.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: s626: factor counter interrupt handling from s626_irq_handler()

Factor the code that handles the counter interrupt out of s626_irq_handler().

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: s626: factor eos interrupt handling from s626_irq_handler()

Factor the code that handles the end of scan interrupt out of
s626_irq_handler().

Remove the printk noise when cfc_write_to_buffer() fails. The user
can't do anything about it anyway.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: s626: use a local var for the s->async in s626_irq_handler()

The comedi_async pointer is used a number of times in this function.
For aesthetic reasons, use a local variable for the pointer.

Also, since was already have a pointer to the "cmd" use that in the
for loop instead of s->async->cmd (or even async->cmd).

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: s626: cleanup "subdevice" and "cmd" in s626_irq_handler()

The comedi_subdevice in this function is actually the dev->read_subdev
that was initialized during the attach of the board. Use that instead
of accessing the dev->subdevices array directly.

Also, get the comedi_cmd used in s626_irq_handler() when the function
is first entered.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: s626: factor dio interrupt handling from s626_irq_handler()

Factor the code that checks and handles the dio interrupts out of
s626_irq_handler().

This allows reducing the number of indents in the code and makes it
easier to follow.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: s626: simplify dio register access

This driver has three dio subdevices, each with 16 channels. These
subdevices use hardware registers that are spaced 0x10 bytes apart
for each "group" of 16 channels.

Create new macros to get the correct addresses for each register
based on the dio "group". Use the s->private (void *) to hold the
"group" number to use in the subdevice functions.

This allows removing struct dio_private and all its uses. It also
removes the ugly casts used to get the register address.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: fix labpc_eeprom_insn_read()

The comedi core expects the (*insn_read) operations to read insn->n
values and return the number of values actually read.

Make this function work like the core expects.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: return bool from labpc_use_continuous_mode()

This is a simple true/false test, return bool instead of int.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: cleanup trigger setting in labpc_ai_cmd()

The (*do_cmdtest) already validated the cmd sources so the default
cases in the switch() statements can never happen.

Preclear to trigger bits and change the switch() statements to simple
if() tests to set the bits.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: remove board attach noise

Remove the kernel noise in labpc_common_attach() as well as a couple
obvious comments.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: dma requires an interrupt

DMA support only works if an interrupt is available.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: allow board to attach without dma

If the dma channel is not available this driver will still work
with interrupts for the analog input subdevice command support.

In addition, only dma channels 1 and 3 are valid for the ISA
devices.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: allow board to attach without interrupt

If the interrupt is not available this driver will still work
with command support disabled for the analog input subdevice.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: return error from labpc_counter_set_mode()

Make sure labpc_counter_set_mode() was successfull and return any
errno back to the caller.

For the if/else conditions that either load the counter of just set
the mode, use a common error patch to check for the error.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: cleanup labpc_counter_load() usage

For aesthetic reasons, move the labpc_counter_load() function so
it's by the labpc_counter_set_mode() function.

Update all the labpc_counter_load() calls so that the I8254_MODE*
enums are used instead of the open coded values.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: introduce labpc_counter_set_mode()

Introduce labpc_counter_set_mode() which is a wrapper around the
i8254_set_mode() helpers to program the 8254 timers. Use the new
function instead of directly writing to the timer mode register
with a "magic" number.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: remove inline from labpc_counter_load()

Let the compiler figure out if this function should be inlined.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: move a couple of the #define's

For aesthetic reasons, move a couple of the #defines in this file
so that the register map defines are first.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: clean up register map

Rename the register map defines to better match the National
Instruments Register-Level Programming Manual for the labpc.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: clean up multi-line comments

Clean up the multi-line comments at the beginning of the file
so that they follow the CodingStyle.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: fix a > 80 char line issue

Fix a checkpatch.pl warning about a line over 80 characters.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: introduce labpc_ai_wait_for_data()

Introduce a helper function to wait for the a/d conversion to
complete.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: introduce labpc_read_adc_fifo()

Introduce a helper function to read the a/d conversion result
from the fifo.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: introduce labpc_setup_cmd6_reg()

Introduce a helper function to set the COMMAND6_REG.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc:use labpc_cancel() to remove some common code

The labpc_cancel() function can be used by the labpc_ai_insn_read() and
labpc_ai_cmd() functions to disable the ai subdevice.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: introduce labpc_ai_set_chan_and_gain()

Introduce a helper function to set the channel and gain bits in the
COMMAND1_REG.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: cleanup local var declarations in labpc_ai_insn_read()

Determine the chan, range, and aref when the variables are declared.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: cleanup local var declarations in labpc_ai_cmd()

Determine the scan_mode early and get the proper chanspec so that
the chan, range, and aref can be determined when the variables are
declared.

labpc_ai_chanlist_invalid() checks that all the range and aref values
in the chanlist are the same so, for consistency, use the same chanspec
used to get the chan.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: remove unnecessary test of dev->irq

The ai subdevice (*do_cmd) pointer is only initialized if the
driver has successfully requested the interrupt. The extra test
in labpc_ai_cmd() is not necessary.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: move declaration of local var 'irq_flags'

In labpc_ai_cmd(), move the declaration of the local variable
'irq_flags' to remove the need for the extra #ifdef/#endif.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: remove DRV_NAME

Remove the DRV_NAME define and just open code the string in the
comedi_driver and pci_driver declarations.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: use dev->board_name instead of DRV_NAME

In labpc_common_attach(), initialize the dev->board_name early and
use that instead of DRV_NAME when allocating the resources.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: move declaration of local var 'dma_flags'

In labpc_common_attach(), move the declaration of the local variable
'dma_flags' to remove the need for the extra #ifdef/#endif.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: tidy up subdevice init

Add some whitespace to the subdevice init.

Remove the unnecessary comment about adding command support to
the analog input subdevice and change the 'maxdata' value to hex
as this is more common in comedi drivers.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: fix 8255 dio subdevice init

The subdev_8255_init() function can fail. Check for failure and
return the errno.

Consolidate the mmio/ioport calls to subdev_8255_init(). The callback
function can be added with a simple ? : test and the cast of the iobase
is not necessary.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: fix command support with analog input subdevice

An interrupt is required for command support to work with the
analog input subdevice. When used with the ISA driver, enabling
the interrupt is optional. Fix the subdevice init so that command
support is only enabled if the irq is available.

Add some whitespace to the subdevice init. Change the 'maxdata'
value to hex as this is more common in comedi drivers.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: rename subdevice (*insn_{read, write}) functions

For aesthetic reasons, and to make grepping easier, rename all the
subdevice (*insn_read) and (*insn_write) functions.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: introduce labpc_range_is_unipolar()

Introduce a helper function to determine if a range selection is
bipolar or unipolar.

This allows removing the static data 'labpc_range_is_unipolar' and
'labpc_plus_is_unipolar' as well as the boardinfo 'ai_range_is_unipolar'.

For consistency, also use the helper in labpc_ao_winsn() when
checking the range.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: rename boardinfo 'memory_mapped_io'

Rename the boardinfo 'memory_mapped_io' to 'has_mmio'.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: rename local var 'thisboard'

For aesthetic reasons, rename the local variable 'thisboard' to
'board'.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: tidy up range table declarations

Tidy up all the tables used to indicate the bipolar/unipolar
type of the range. the gain bits used to set the range, and the
comedi_lrange.

Remove a couple unnecessary #define's used to indicate the size
of the tables as well as some unnecessary comments.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: rename some of the private data variables

For aesthetic reasons, rename the 'command*_bits' and 'status*_bits'
variables in the private data in order to shorten some of the long
lines.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: remove 'volatile' from private data

As indicated by checkpatch.pl, "WARNING: Use of volatile is usually
wrong: ...". The variables in the private data that are marked
volatile don't need to be. Remove the volatile.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: cleanup the boardinfo

For aesthetic reasons, add some whitespace to the boardinfo.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: remove "dummy" pci boardinfo entry

This driver uses the comedi auto config mechanism to attach to PCI
boards. The "dummy" entry in the boardinfo table is not needed.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: remove boardinfo data that is set to '0'

It's not necessary to initialize the boardinfo data that is set
to '0'.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: remove forward declarations 4

Move the analog input support functions to remove the need for the
remaining forward declarations.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: remove forward declarations 3

Move the interrupt/dma support functions to remove the need for
some of the forward declarations.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: move the analog output support functions

For aesthetic reasons, move the analog output support functions.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: remove forward declarations 2

Move the eeprom/caldac support functions to remove the need for
some of the forward declarations.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: remove forward declarations 1

Move the comedi_driver (*attach), (*auto_attach), and (*detach)
functions as well as a couple of the attach helper functions to
remove the need for a number of the forward declarations.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: add some whitespace to the *_driver declarations

For aesthetic reasons, add some whitespace to the comedi_driver and
pci_driver as well as the pci device table declarations.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: remove thisboard macro

The 'thisboard' macro relies on a local variable having a specific
name and yields a pointer derived from that local variable.

Replace the macro with a local variable and use the comedi_board()
helper to get the const pointer.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: ni_labpc: rename labpc_board_struct

For aesthetic reasons, rename labpc_board_struct to labpc_boardinfo.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: Kconfig: update CONFIG_AMPLC_DIO200_PCI help text

After splitting support for PCI cards out of the "amplc_dio200" module
into "amplc_dio200_pci", the help text needs updating.

Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: amplc_dio200: split into ISA, PCI and common

Split the "amplc_dio200" comedi driver module into separate driver
modules for ISA and PCI boards with a common module for the shared code.

Keep the old name "amplc_dio200" for the ISA board driver as the module
may be modprobed with this name by a script.  (If the script uses insmod
it will need modifying to load the "amplc_dio200_common" module first.)

Use the module name "amplc_dio200_pci" for the PCI board driver.  On
most systems this will be auto-loaded.

Use the module name "amplc_dio200_common" for the module containing the
shared code.  This is normally loaded as a dependency of the other two
modules.

"amplc_dio200_common" exports the following functions:

* `amplc_dio200_common_attach()`: this is basically the old
  `dio200_common_attach()` from the combined driver module.  It is
  called from the driver-specific attach or auto-attach routines.
* `amplc_dio200_common_detach()`: this is most of the old
  `dio200_detach()`.  It is called from the driver-specific detach
  routine.
* `amplc_dio200_set_enhance()`: this is a new function called during
  initialization of PCIe cards to enable "enhanced" mode.

Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: amplc_dio200: refactor dio200_handle_read_intr()

Refactor `dio200_handle_read_intr()` to fix checkpatch warning about too
many leading tabs.  Factor out the part that puts the scan data into the
asynchronous command data buffer and checks for end of acquisition into
new function `dio200_read_scan_intr()`.

Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: amplc_dio200: don't check bus-type in dio200_common_attach()

The "amplc_dio200" driver is going to be split into separate drivers for
ISA and PCI cards with a common module containing most of the code.  We
don't want the common module code to depend on whether ISA boards, PCI
boards, or both are supported.  Currently, `dio200_common_attach()` and
`dio200_detach()` optimize out the code to support a timer subdevice
when built to support ISA boards only.  Remove the `if (DO_PCI)` tests
which optimize out that code.  Unfortunately, this will expand the
module's code size for an ISA-only driver a bit.

Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>