cryptodev-linux: change home-page URL

Most links and info on the org page are broken or defunct, and all new
versions are available on the github based repo anyway.

Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16910
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit ce0b843ac7d27e124cb9ca13e9a1aeb115fcaf23)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>

cryptodev-linux: give a coherent description

For the last ten years, nobody has noticed that this driver doesn't
actually say what it is for. ;)

Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16910
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 3df5966f9453ecefcabc893f6449c8c4f1054aef)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>

realtek: rtl83xx: use devm for mutex_init

mutex_destroy is missing in remove.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16926
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 1125ed408c7f0d130b5606ab39e4dd98a41d5f0a)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>

ramips: mt7621: fix typo

Missing u caused the regulator to fail probe.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16925
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 3e42526404f021094ae3fa41524c396d753f4c6c)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>

mdadm: backport musl patch

Needed to fix compilation with GCC14.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16912
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 1f3d5858b441cf4e1195b96242dd08d68538e83d)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>

lantiq: use devm for mutex_init

It's common to avoid calling mutex_destroy when done. It's not correct strictly speaking.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16832
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit fccff963c0a6ba035455daea61566f4d121643e3)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>

lantiq: use more devm for i2c

i2c_add_numbered_adapter is the wrong function to use here. It requires
setting nr to some value, otherwise it behaves the same as
i2c_add_adapter. nr is not set.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16825
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 44824f0b787b13e2f2fccc58256b2c42fa3f9f5d)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>

treewide: remove THIS_MODULE assignment

Matches upstream coccinelle check: api/platform_no_drv_owner.cocci.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16846
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit cc98cfafd799d502fbe09ddb62bab68633d570f5)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>

hostapd: split long lines

These two were getting rather long.

Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
Link: https://github.com/openwrt/openwrt/pull/16849
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 8b6d5874b88bbe2e7a53bcab0e102b8781480880)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>

menuconfig: add help description for Stack Smashing Protection options

Descriptions taken from:
https://wiki.osdev.org/Stack_Smashing_Protector

Signed-off-by: Marius Dinu <m95d+git@psihoexpert.ro>
Link: https://github.com/openwrt/openwrt/pull/16897
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit cbf7be9fb37baaaf7ee5c2b6315028bd47c764bc)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>

ramips: mt7621: add missing regulator-boot-on

What seems to be happening is that the kernel requests an ACTIVE_LOW
gpio initially and sets it to high later based on gpios in dts.

This seems to break some devices where the bootloader sets it to high.

Fixes: e612900ae0 ("ramips: mt7621: convert usb power to regulators")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16877
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit a7bc6bf7dba98c77724cb8284d21a9c77c263d56)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>

rampis: mt7621: Edgerouter-X adjust IMAGE_SIZE to reflect new kernel size

IMAGE_SIZE was previously set to kernel1 + ubi size = 256768k, now
kernel1 is 6MB adjust this value to add 3072k to total image size.

Signed-off-by: Tim Lunn <tim@feathertop.org>
Link: https://github.com/openwrt/openwrt/pull/15194
(cherry picked from commit 5b406bccaccadb494cad139b3f69e17ab62d3968)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>

ramips: mt7621: Edgerouter-X drop factory image

Edgerouter-X factory images have not built automatically since 19.x due
to images being over 3MB. While it was possible to build custom images
with very stripped down config, this is no longer possible with the size
increases of linux 6.1 and 6.6.

Drop code for generation of factory images, if some dev later wishes to
try custom images they can revert this commit.

Signed-off-by: Tim Lunn <tim@feathertop.org>
Link: https://github.com/openwrt/openwrt/pull/15194
(cherry picked from commit 4d90b79704efba57ab158c47ae6936ce4c1ef185)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>

rampis: mt7621: Re-enable Edgerouter-X image builds

With the new layout providing 6MB for kernel there will be no issues
with kernel size affecting build of images.

Re-enable image builds for Edgerouter-X and X-SFP.

Signed-off-by: Tim Lunn <tim@feathertop.org>
Tested-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Link: https://github.com/openwrt/openwrt/pull/15194
(cherry picked from commit 71b4842e3bdaed91cd2daa4b28a208559c3de7c6)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>

rampis: mt7621: Edgerouter-X update compat version to 2.0

Use compat version to indicate that the new layout for larger kernels
is in place. This handled by the patch to ubnt.sh to always select
the kernel1 slot for flashing and as active kernel slot.

Signed-off-by: Tim Lunn <tim@feathertop.org>
Tested-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Link: https://github.com/openwrt/openwrt/pull/15194
(cherry picked from commit 1bdbd511b27017157e92ffe128e66853d169dcbf)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>

rampis: mt7621: Edgerouter-X set compat version message

Refer user to the wiki page for instructions on how to migrate to the
new kernel layout.

Signed-off-by: Tim Lunn <tim@feathertop.org>
Tested-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Link: https://github.com/openwrt/openwrt/pull/15194
(cherry picked from commit 70c371d91cda300d7c655f019cb2076d2dd537fb)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>

rampis: mt7621: resize Edgerouter-X kernel size to 6MB

With the updated partition layout set in dts, set the KERNEL_SIZE
parameter to 6MB allowing builds of Linux 6.1 and later to fit.

Signed-off-by: Tim Lunn <tim@feathertop.org>
Tested-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Link: https://github.com/openwrt/openwrt/pull/15194
(cherry picked from commit 09a6bffb6e0a714f20d71043ae8382af4c5925b6)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>

rampis: mt7621: Edgerouter-X disable toggling of kernel slots

Uboot selects which kernel slot to boot based on a flag in the factory
mtd partition. Patch ubnt.sh to ensure always flash to kernel1 slot and
update flag if required.

Signed-off-by: Tim Lunn <tim@feathertop.org>
Tested-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Link: https://github.com/openwrt/openwrt/pull/15194
(cherry picked from commit 5e355f1f9084c1b6de3151fbcde948d736292d6c)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>

rampis: mt7621: Convert Edgerouter-X dts to single kernel config

The OEM layout for Edgerouter X provides for two 3MB kernel slots.
As of linux 6.1 the kernel images no longer fit and as such
Edgerouter X builds have been disabled in Main.

Revise the layout to make kernel1 slot 6MB and drop kernel2 slot.

This patch applies the required changes to the dts file.

Signed-off-by: Tim Lunn <tim@feathertop.org>
Tested-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Link: https://github.com/openwrt/openwrt/pull/15194
(cherry picked from commit dc51c4355d48e91ed8fd06d70f0bf71b0b4bc4d2)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>

fritz-tools: fix mixed indentation

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 685e979d470a09361defe1612b001dfc3b7d9832)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>

packages: drop DEVICE specific dependency for omnia

Both packages `ombnia-mcu-firmware` and `omnia-mcutool` would depend on
a specific device. The buildbots however build all devices and therefore
the package isn't build at all, due to unmet dependencies.

While this didn't cause issues with OPKG, APK fails actively due to the
missing packages. Drop the specific dependency, however wants to install
unrelated firmware on any device can do that anyway.

Signed-off-by: Paul Spooren <mail@aparcar.org>
(cherry picked from commit f35a29d63f445d784f1e266eaa6d3825a249cd6c)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>

ath79: gpio-rb91x-key: use gpiochip_get_data

No need for a custom function that does the same thing.

Oversight from devm conversion.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16748
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit e99b5832e801fdf2ec366419797360e09c2348c6)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>

ath79: gpio-latch-miktorik: use gpiochip_get_data

Oversight from devm conversion. No need for a custom static inline
function.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16747
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 6d2ed484fa2f62e355893f5e1fe3734c88201bfc)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>

ramips: mt7621: convert usb power to regulators

These things are regulators. Should silence dmesg messages about using
dummy regulators.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16804
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit e612900ae0fd6c4624fa661e004536216409107f)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>

kernel: can: package driver for Geschwister Schneider interface

Package gs_usb CAN driver, which is for Geschwister Schneider and
bytewerk.org candleLight compatible USB/CAN interfaces.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
(cherry picked from commit ef4df2b5e9d66a6461982a0a81f928abb0f6a074)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>

ipq40xx: use devm for mutex_init

Avoids having to call mutex_destroy in remove.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16755
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 57f2c72505f24b41fd9beaef3a8aa713b436cdb9)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>

build: profiles.json: add kernel version information

Currently downstream tools like ASU lack information about kernel
version to find out the relevant kmod build folder on downloads server.

So lets fix it by providing a new `linux_kernel` JSON array which would
for the start provide Linux kernel version, revision and vermagic
information.

  "linux_kernel": {
     "release": "1",
     "vermagic": "b57450c07d3a786158c3601fc5cee57d",
     "version": "6.6.61"
   },

Fixes: openwrt/openwrt#17036
Fixes: efahl/owut#9
Co-developed-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17042
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit c857145e034f623e31ab2028049a547ecd94ce85)

mtd-utils: add ubihealthd to nand-utils

Add ubihealthd to the nand-utils package, auto-create UCI config for
each UBI device and launch the daemon on boot.

The default time interval between scrubbing a random PED is 120 seconds
which means that a fully used 128 MiB flash chip gets scrubbed in about
a day and a half. The interval can be adjusted in UCI using the
'interval' option.

Suggested-by: Rodrigo Balerdi <lanchon@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://github.com/openwrt/openwrt/pull/16973
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 7e287b563aa1043a1af54d5e2b0bd96326371732)

procd: update to git HEAD

 7330fa5 initd: mount /sys and /proc with MS_RELATIME

Fixes mounting /proc in unpriviledged user namespace.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 1e8505ac4e88212106fe78486cfcbe9cae7660f9)

include: meson.mk: honor CONFIG_DEBUG

Set buildtype according to CONFIG_DEBUG.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit be3e7a84bd37f29e14e4c6a89b8c79bc9808c36c)

include: cmake.mk: honor CONFIG_DEBUG

Set CMAKE_BUILD_TYPE according to CONFIG_DEBUG.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit fc9ec5bd3d22d50654af154fc779517fa7aecb33)

kernel: modules: package driver for generic MIPI DBI TFT panels

Package kmod-drm-panel-mipi-dbi as well as modules it depends on in
order to support a wide range of MIPI DBI complaint SPI-connected
TFT panels.

See https://github.com/notro/panel-mipi-dbi/ for more information on
how to use specific panels.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 0a7b7ef27cfc00521a0f99de073a7168f1b79e8f)

ramips: mt7621: support openwrt,netdev-name for renaming interfaces

Edgerouter X currently has its eth1 port on the switch missing since there
is a naming conflict currently.

So, as the root cause is mixing kernel support for DSA interfaces having
predictable names set via "label" property vs others having it assigned
dynamically lets avoid the conflict by using our own custom property as
suggested upstream [1].

So, add support via "openwrt,netdev-name" property and use it on ERX.

Fixes: 2a25c6ace8d8 ("ramips: get rid of downstream network device label patch")
Fixes: #15643
Link: https://github.com/openwrt/openwrt/pull/17062
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 5695267847c2fe51290fdbde6ecd7114654f7988)

wifi-scripts: Fix parsing of Capabilities

Fixup capabilities parsing in iw output.

In addition to the normal capabilities iw now also outputs HE MAC, HE
PHY and EHT MAC and EHT PHY capabilities. Exclude them in the parsing.

The grep returns this with mac80211-hwsim:
```
root@OpenWrt:~# iw phy phy0 info | grep 'Capabilities:'
Capabilities: 0x107e
HE PHY Capabilities: (0x02bfce0000000000000000):
EHT PHY Capabilities: (0x7c0000feffff7f01):
HE PHY Capabilities: (0x02bfce0000000000000000):
EHT PHY Capabilities: (0x7c0000feffff7f01):
HE PHY Capabilities: (0x02bf000000000000000000):
Capabilities: 0x107e
HE PHY Capabilities: (0x1cbfce0000000000000000):
EHT PHY Capabilities: (0xfc1f3ffeffff7f37):
HE PHY Capabilities: (0x1cbfce0000000000000000):
EHT PHY Capabilities: (0xfc1f3ffeffff7f37):
HE PHY Capabilities: (0x1cbf000000000000000000):
HE PHY Capabilities: (0x1cbfce0000000000000000):
EHT PHY Capabilities: (0xfefffffeffffff7f):
HE PHY Capabilities: (0x1cbfce0000000000000000):
EHT PHY Capabilities: (0xfefffffeffffff7f):
HE PHY Capabilities: (0x1cbf000000000000000000):
Capabilities: 0x107e
```

With busybox 1.36.1 the ht_cap_mask variable will be set to
-72057598332895361. With busybox 1.37.0 it will be set to -1.
Both values are wrong, after this change it will be set to 4222
(0x107E).

Link: https://github.com/openwrt/openwrt/pull/17043
(cherry picked from commit adf958c9192d94fbeeb0ec8e16800b0071455909)
Link: https://github.com/openwrt/openwrt/pull/17055
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: bump 6.6 to 6.6.63

Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.63

Manually rebased:
bcm27xx/patches-6.6/950-0297-staging-vchiq_arm-Add-36-bit-address-support.patch

All other patches automatically rebased.

Build system: x86/64
Build-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Run-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/16997
(cherry picked from commit eb395585ae1b7560bbcea9544f428db2a9105152)
Link: https://github.com/openwrt/openwrt/pull/17055
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: bump 6.6 to 6.6.62

Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.62

All patches automatically rebased.

Build system: x86/64
Build-tested: x86/64/AMD Cezanne, flogic/glinet_gl-mt6000, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Run-tested: x86/64/AMD Cezanne, flogic/glinet_gl-mt6000, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/16997
(cherry picked from commit 611bfa4d72c87e8163d7193d9557479fc7312467)
Link: https://github.com/openwrt/openwrt/pull/17055
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

debugcc: Mark it nonshared

This tool was build in the phase 2 build, there the TARGET dependencies
are probably not meat. Mark it as non shared to build it together with
the targets where this option is set.

Link: https://github.com/openwrt/openwrt/pull/16975
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit febe1db43d1a01f83e474bcb143dcb3997bd35a3)
Link: https://github.com/openwrt/openwrt/pull/17055
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

ath79: lzma-loader: fix syntax error

C compiler can't parse '#else if'.

Fixes: f84a9f7dc095 ("ath79: add support for Huawei AP6010DN")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16989
(cherry picked from commit 98f26346cbbb45e5c0417f57846ce1783e884ea2)
Link: https://github.com/openwrt/openwrt/pull/17055
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: bump 6.6 to 6.6.61

Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.61

Manually rebased:
bcm27xx/patches-6.6/950-0998-i2c-designware-Add-support-for-bus-clear-feature.patch

All other patches automatically rebased.

Build system: x86/64
Build-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Run-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/16959
(cherry picked from commit 487ca61f917f9308222faf481ad8be4e2cef0c90)
Link: https://github.com/openwrt/openwrt/pull/17055
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

mediatek: fix Cudy AP3000 Outdoor label-mac

The label-mac does not match the one assigned to the ethernet interface.
Use the mac-address assigned to the wifi interface instead, as it
matches the one found on the device label.

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit b8b658bc0d22df31e7ac2d07cdd2af7155d12630)

imagebuilder: fix OPKG package_whatdepends support

Trying to use 'package_whatdepends' feature of the ImageBuilder with OPKG
will currently fail as OPKG does not support "list --depends" call at all,
it seems that this is a mixup from the original APK support commit.

So, lets restore 'package_whatdepends' support for OPKG by calling
"whatdepends -A" instead as we used to before APK support.

Fixes: d788ab376f85 ("build: add APK package build capabilities")
Link: https://github.com/openwrt/openwrt/pull/17022
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 52519a59a859d349f154ed79e0a3d63457b6aa6a)

ipq806x: tr4400v2: fix dtc warnings by deleting stock partitions

The original set of stock partitions was kept in the TR4400 v2 port,
with the same partition numbers but their names prefixed with 'stock_'.
This allowed scripts (installation, back to stock, etc) to run on both
stock and OpenWrt firmware. But this triggers warnings in the device
tree compiler, as partitions of the old and new schemes overlap.

This commit fixes the dtc warnings by deleting the stock partitions,
also renumbering some of the remaining MTD partitions in the process.
Additionally, the 'fw_env' partition is set to read-only.

These changes can break existing scripts as well as user configurations
that utilize the 'extra' partition. Users wanting to run old scripts can
do so by reverting to the 23.05 series releases.

Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16958
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 8ec35a2a1533ccff8a4b0e6f4f0a0954d1bee6a6)

net: phy: broadcom: update dependency condition

The broadcom PHY driver only has to depend upon PTP_1588_CLOCK_OPTIONAL
if NETWORK_PHY_TIMESTAMPING is enabled. The PTP functionality is stubbed
in this case.

Reflect this circumstance in the dependence condition. This allows to
build the driver as a built-in module even if PTP is built as a module.

This is required to include the broadcom PHY module regardless of the
built-setting of the PTP subsystem. On ath79 (and probably more)
targets with Broadcom PHY, Gigabit operation is currently broken as the
PHY driver is only built as a module in case all kernel-packages are
built. Due to this circumstance, affected devices fall back to using the
generic PHY driver.

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit cbce32e30c29dc69907c6f4c0ab79dd5d9a8fb28)

airoha: an7581: sync patch with upstream version and tag them

Sync patch with upstream version and tag them.
Minor changes done to Pinctrl patch to support older kernel.

Patch automatically refreshed with make target/linux/refresh.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit a5d23e3aee9bd616044c3eadfe2dbcad5d18b163)

mac80211: backport some upstream fixes

Fix various issues, including potential crashes

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 53eab6198bf87d12055409bc4a38d58b68291b2f)

ath79: Add support for Sophos AP15C

The Sophos AP15C uses the same hardware as the AP15, but has a reset button.

Based on:
commit 6f1efb289837 ("ath79: add support for Sophos AP100/AP55 family")
author    Andrew Powers-Holmes <andrew@omnom.net>
          Fri, 3 Sep 2021 15:53:57 +0200 (23:53 +1000)
committer Hauke Mehrtens <hauke@hauke-m.de>
          Sat, 16 Apr 2022 16:59:29 +0200 (16:59 +0200)

Unique to AP15C:
 - Reset button
 - External RJ45 serial console port

Flashing instructions:

This firmware can be flashed either via a compatible Sophos SG or XG
firewall appliance, which does not require disassembling the device, or via
the U-Boot console available on the internal UART header.

To flash via XG appliance:
 - Register on Sophos' website for a no-cost Home Use XG firewall license
 - Download and install the XG software on a compatible PC or virtual
   machine, complete initial appliance setup, and enable SSH console access
 - Connect the target AP device to the XG appliance's LAN interface
 - Approve the AP from the XG Web UI and wait until it shows as Active
   (this can take 3-5 minutes)
 - Connect to the XG appliance over SSH and access the Advanced Console
   (Menu option 5, then menu option 3)
 - Run `sudo awetool` and select the menu option to connect to an AP via
   SSH. When prompted to enable SSH on the target AP, select Yes.
 - Wait 2-3 minutes, then select the AP from the awetool menu again. This
   will connect you to a root shell on the target AP.
 - Copy the firmware to /tmp/openwrt.bin on the target AP via SCP/TFTP/etc
 - Run `mtd -r write /tmp/openwrt.bin astaro_image`
 - When complete, the access point will reboot to OpenWRT.

To flash via U-Boot serial console:
 - Configure a TFTP server on your PC, and set IP address 192.168.99.8 with
   netmask 255.255.255.0
 - Copy the firmware .bin to the TFTP server and rename to 'uImage_AP15C'
 - Open the target AP's enclosure and locate the 4-pin 3.3V UART header [4]
 - Connect the AP ethernet to your PC's ethernet port
 - Connect a terminal to the UART at 115200 8/N/1 as usual
 - Power on the AP and press a key to cancel autoboot when prompted
 - Run the following commands at the U-Boot console:
    - `tftpboot`
    - `cp.b $fileaddr 0x9f070000 $filesize`
    - `boot`
 - The access point will boot to OpenWRT.

Signed-off-by: David Lutz <kpanic@hirnduenger.de>
(cherry picked from commit a7abc7ec3b61be553f33c49e5acc90a4d539d992)

nftables: update to 1.1.1

Release Announcement:
https://lwn.net/Articles/982283/
https://lwn.net/Articles/992760/

Link: https://github.com/openwrt/openwrt/pull/16769
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit c11a18be0dc38c81280baa948500fe1a57de0685)

libnftnl: update to 1.2.8

Release Announcement:
https://www.spinics.net/lists/netfilter-devel/msg87287.html
https://www.spinics.net/lists/netfilter-devel/msg88520.html

Link: https://github.com/openwrt/openwrt/pull/16769
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit d9ed0d438b0ec7d813764d629be7a753dc3fbac5)

base-files: Remove pkg_check when using apk

/sbin/pkg_check uses opkg and is not even packaged when using the
default opkg configuration. remove it when using apk too.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 0ce237a20cc5168c62afcacb3b47d77a952d64c1)

mt76: update to Git HEAD (2024-10-28)

8dfead68c202 wifi: mt76: mt7915: hold dev->mutex while interacting with the thermal state
d508a6eb935d wifi: mt76: mt7996: use mac80211 .sta_state op
57019e663f57 wifi: mt76: add code for emulating hardware scanning
dc4c2bdf7c56 wifi: mt76: add support for allocating a phy without hw
8cd0263f92e1 wifi: mt76: rename struct mt76_vif to mt76_vif_link
99df84d62883 wifi: mt76: add vif link specific data structure
dcc6f158d759 wifi: mt76: mt7996: split link specific data from struct mt7996_vif
d388deab9e73 wifi: mt76: initialize more wcid fields mt76_wcid_init
d026be405c54 wifi: mt76: add chanctx functions for multi-channel phy support
0b05795ca81c wifi: mt76: remove dev->wcid_phy_mask
0b526090de95 wifi: mt76: add multi-radio support to a few core hw ops
aeedee5c0a2c wifi: mt76: add multi-radio support to tx scheduling
fc0ff17b53ff wifi: mt76: add multi-radio support to scanning code
f19cbcf83400 wifi: mt76: add multi-radio remain_on_channel functions
42429ae0eaf6 wifi: mt76: mt7996: use emulated hardware scan support
f9d593d4a6b4 wifi: mt76: mt7996: pass wcid to mt7996_mcu_sta_hdr_trans_tlv
807090b28661 wifi: mt76: mt7996: prepare mt7996_mcu_add_dev/bss_info for MLO support
252baa7bf477 wifi: mt76: mt7996: prepare mt7996_mcu_add_beacon for MLO support
9ee990050305 wifi: mt76: mt7996: prepare mt7996_mcu_set_tx for MLO support
bf12cc404334 wifi: mt76: mt7996: prepare mt7996_mcu_set_timing for MLO support
60bf2bef95dc wifi: mt76: connac: prepare mt76_connac_mcu_sta_basic_tlv for MLO support
1289737e12a8 wifi: mt76: mt7996: prepare mt7996_mcu_update_bss_color for MLO support
7c00df0e7e57 wifi: mt76: connac: rework connac helpers
484e3f289a40 wifi: mt76: mt7996: move all debugfs files to the primary phy
d258f4e3e1ca wifi: mt76: mt7996: switch to single multi-radio wiphy
c246fa545119 wifi: mt76: mt7996: fix monitor mode

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 6720c4ccba256186bf2f1b1edadb851c447e62a5)

netifd: update to Git HEAD (2024-11-08)

e93f6c3fc729 main: fix format string related warnings for log/debug printf functions
6ab44a2413f9 fix signed/unsigned comparison warnings
4fe997b61d7d system-dummy: add system_if_apply_settings_after_up
992d33cb42a6 ubus: add notifications on wireless device state changes
34eb11eb6f5c device/interface: add "tags" attribute from config to status dump

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 5f68e243338a653f44f079acc001de369aa42efa)

wifi-scripts: add free-form "tags" array option for wifi-iface

This allows annotating wifi interfaces in the config in a way that can be
queried through wifi status. One example use case is to mark wifi interfaces
for use with specific services without having to explicitly reference the
(often unnamed) sections from elsewhere.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit a3ec35cadb77265c0e00c8d3789734586a6f7111)

ipq806x: tr4400v2: revert nesting of MTD partitions that bricks device

This reverts commit e1043a746a1030062e73ea027d9a35c58bce6c6a, that
attempts to nest partitions that overlap but are not nested. This
causes the 'ubi' partition to be truncated, making rootfs inaccessible
and bricking the device.

Also, had this commit worked, it would have renumbered MTD partitions
in a way that would have broken documented scripts for installation and
update of main and recovery OSes, making backups, return to stock, etc,
and broken user configurations that put the 'extra' partition to use.

Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16944
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 0e59eaa7962fc21635af5c9d2f6552a4accdc7ea)

base-files: improve default root-passwd script

The script was not exiting cleanly causing it to not be removed from the
uci-defaults folder.

Signed-off-by: John Crispin <john@phrozen.org>

airoha: an7581: backport upstream ethernet fixes

Backport patches fixing some ethernet problem merged upstream.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>

kernel: bump 6.6 to 6.6.60

Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.60

Removed upstreamed:
generic/backport-6.6/409-mtd-spi-nor-winbond-fix-w25q128-regression.patch

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.60&id=27a58a19bd20a7afe369da2ce6d4ebea70768acd

Build system: x86/64
Build-tested: x86/64/AMD Cezanne, flogic/glinet_gl-mt6000, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Run-tested: x86/64/AMD Cezanne, flogic/glinet_gl-mt6000, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/16892
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry picked from commit 85844cfc5c591d00997ade665340315d54bc5822)

mac80211: compatibility with kernel 6.6.59

Fix genlmsg_multicast_allns() build error on kernel 6.6.59.
Based on kernel patch https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit?h=v6.6.59&id=e0f83d268974dab0361d11904dfc9acec53f96a6

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16835
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 31f1dabb4b9727b300ddaa2801903ae4b72e4e1e)
Link: https://github.com/openwrt/openwrt/pull/16894
Signed-off-by: Robert Marko <robimarko@gmail.com>

kernel: bump 6.6 to 6.6.59

Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.59

Removed upstreamed:
 - generic/backport-6.6/777-netfilter-xtables-fix-typo-causing-some-targets-to-not-load-on-IPv6.patch[1]
 - generic/backport-6.6/780-24-v6.12-r8169-avoid-unsolicited-interrupts.patch[2]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.59&id=433742ba96baf30c21e654ce3e698ad87100593b
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.59&id=7d6d46b429804b1a182106e27e2f8c0e84689e1a

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16835
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 4fc47c60006ccacda5ef644c5447ebfcb26c0680)

vrx518_tc: allow larger MTU to support RFC4638

vrx518_tc currently sets the interface maximum MTU to the ethernet default
of 1500 bytes by default via ether_setup() called from ptm_setup().

To support 1508 byte baby jumbo frames (RFC4638) for PPPoE connections
over VDSL links as already supported by the VR9 ltq_ptm driver ([1], [2])
set the interface maximum MTU to MAX_MTU.

MAX_MTU is defined in dcdp/inc/tc_common.h to 2002 bytes and this value is
used in ptm_change_mtu() and elsewhere as the maximum MTU, however this is
short circuited by checks against the interface maximum MTU.

[1]: https://forum.openwrt.org/t/fritzbox-7530-and-rfc4638-baby-jumbo-frames/181327
[2]: https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=8a2a20e71e2909f84dab47e51dfda9e292a6c1ae

Signed-off-by: Andrew MacIntyre <andymac@pcug.org.au>
Link: https://github.com/openwrt/openwrt/pull/16856
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit ca53f2d430ce1f9ff5a560291de1e93380963417)

ath79: linksys_ea4500-v3: take over the space for user data

The last "syscfg" partition of the OEM firmware turns out to be a
UBIFS used to store user data, just as the "rootfs_data" of OpenWrt,
so it should be reasonable to absorb it into the "ubi" partition.

Factory installations via either OEM firmware or tftp, or by forcibly
flashing factory image to mtd5 (firmware) partition with mtd tool are
confirmed working, but the UBI remaining inside "syscfg" partition
could break upgrade. Fortunately, installing kmod-mtd-rw and erasing
"syscfg" partition before upgrade is confirmed working, in which case,
"ubi" will automatically expand to the blank space once occupied by
the former mtd8 (syscfg), with the total block number increased, but
the UBIFS for rootfs_data will not automatically claim the newly
available space (since it is created when mtd8 still exists, and
sysupgrade does not set "autoresize" flag to rootfs_data). These space
will be claimed during the next upgrade, when rootfs_data is removed
and created again.

Fixes: 50f727b7737d1 ("ath79: add support for Linksys EA4500 v3")
Signed-off-by: Edward Chow <equu@openmail.cc>
Link: https://github.com/openwrt/openwrt/pull/14791
Signed-off-by: Robert Marko <robimarko@gmail.com>

kernel: r8125: update to v9.014.01

Changelog: https://github.com/openwrt/rtl8125/compare/9.013.02...9.014.01

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit e29bc67f9d8451d3baf80da9358b3a01dc4b20b7)

procd: update to Git HEAD (2024-11-06)

109fa41b2321 system: fix description value from os-release

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 09a8b4920cf117942561237d639d5101283a53c4)

kernel: r8168: refresh patch

Patches weren't refreshed when r8168 was updated to v8.054.00 in a85e18b53f0f.

Fixes: a85e18b53f0f ("kernel: r8168: update to v8.054.00")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 6490c88c75b3392aca9dae5f4d47a13a0aa35220)

kernel: r8126: update to v10.014.01

Changelog: https://github.com/openwrt/rtl8126/compare/10.013.00...10.014.01

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 562b2c22fff363f060e72c9018d243981b7d6447)

mediatek: set 7 MACs per wifi band in board.json on OpenWrt One

Mass production units will get 16 assigned MAC addresses. This allows each phy
to spawn up to 7 VAPs which will each have unique MAC without needing the
private bit.

Signed-off-by: John Crispin <john@phrozen.org>

mediatek: set mac increment to 7 for the 5G radio on OpenWrt One

Mass production units will get 16 assigned MAC addresses. This allows each phy
to spawn up to 7 VAPs which will each have unique MAC without needing the
private bit.

Signed-off-by: John Crispin <john@phrozen.org>

mediatek: refresh patches

The mediatek target requires refreshing after recent additions.

Fixes: cfe8e6e75f ("mediatek: add support for Realtek RTL8261n 10G PHYs")
Fixes: ddfae94a14 ("mediatek: add support for swapping the polarity on usxgmii interfaces")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>

mediatek: filogic: BPi-R4: wire up pinctrl for pwm-fan

Assign pwm function of PWM0 pin to the pwm-fan.
This is mostly just cosmetics as it basically reflects the default
setting of that pin.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

mediatek: pinctrl-mt7988: add missing PWM pingroups

Add additionals possible pinctrl group for pwm2~7 on pins
pin  4 (GPIO_A)        pwm7
pin 58 (JTAG_JTDI)     pwm2
pin 59 (JTAG_JTDO)     pwm3
pin 60 (JTAG_JTMS)     pwm4
pin 61 (JTAG_JTCLK)    pwm5
pin 62 (JTAG_JTRST_N)  pwm6

They can be useful e.g. on the BPi-R4 as in that way pwm2~6 can be exposed
on the 26-pin header (pwm6 always, pwm2~5 instead of the full UART).

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

uboot-mediatek: import patches improving menu navigation

Using the arrow keys to navigate the U-Boot menu often leads to being
dropped into the U-Boot shell unexpectedly.
This can be prevented in most cases by improving the logic to detect the
arrow key ESC sequence and only reprinting the menu if actually needed.
Also enable CONFIG_SERIAL_RX_BUFFER for all boards as it helps preventing
the remaining cases.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

mediatek: filogic: add Arcadyan Mozart platform

* Mediatek MT7988A (4x Cortex-A73, up to 1.8 GHz clock speed)
* 8 GiB eMMC
* 4 GiB DDR4 RAM
* 2x 10000M + 1x 1000M  ports
* MT7996 Tri-band (2.4G, 5G, 6G) 4T4R 802.11be Wi-Fi
* 2 buttons (Reset, WPS)
* 2x LED for each GMAC
* USB-C PD power input

Signed-off-by: John Crispin <john@phrozen.org>

mediatek: add support for swapping the polarity on usxgmii interfaces

This patch comes from the MTK SDK.

Signed-off-by: John Crispin <john@phrozen.org>

mediatek: add support for Realtek RTL8261n 10G PHYs

There is no upstream driver yet. Merge the RTL SDK driver for now.

Signed-off-by: John Crispin <john@phrozen.org>

uboot-mediatek: add support for arcadyan,mozart

Signed-off-by: John Crispin <john@phrozen.org>

nu801: Mark as nonshared to build in step 1

Mark the package as nonshared to build it in the target specific build
step 1 of the build bots instead of the architecture generic build step 2.

In the build step 2 it may be left out if we build it using a different
target.

Fixes: #16857
Link: https://github.com/openwrt/openwrt/pull/16859
Signed-off-by: Robert Marko <robimarko@gmail.com>

ramips: Fix EX400 imagebuilder

A factory image for DNA EX400 depends on an initramfs image and they
were explicitly removed from the imagebuilder recently. Now the factory
image creation fails miserably and it also affects custom image creation
with the firmware selector.

Add the initramfs kernel to the staging so that it's shipped with the
imagebuilder. Also remove a image build target added solely for DNA EX400.

Tested by creating a factory and syspupgrade images locally with
the imagebuilder and verified their functionality.

Related work
  c85348d9abf4 ("imagebuilder: remove initramfs image files")

Fixes: fea2264d9fdd ("ramips: mt7621: Add DNA Valokuitu Plus EX400")
Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
---
v4: use append-image-stage, remove Build/kernel-initramfs-bin
v3: adjust commit subject
v2: remove fix for inconsistent line ending elsewhere in the file
Link: https://github.com/openwrt/openwrt/pull/16659
Signed-off-by: Robert Marko <robimarko@gmail.com>

uboot-mediatek: fix boot media for mt7981 RFB NOR profile

Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
CC: Daniel Golle <daniel@makrotopia.org>

gpio-button-hotplug: use flexible array member

zero length arrays are deprecated.

Fixes coccinelle warning:

WARNING use flexible-array member instead

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16848
Signed-off-by: Robert Marko <robimarko@gmail.com>

mtd: Add backported Winbond fix

Upstream stable is slow at picking this up and several systems
are regressing. Add the patch locally in OpenWrt.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

mediatek: YunCore AX835: fix voltage regulator

Specifying GPIO_ACTIVE_HIGH on the GPIO for the voltage regulator doesn't
suffice. The regulator itself requires enable-active-high to be set.

Fixes: #16292
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
Link: https://github.com/openwrt/openwrt/pull/16839
Signed-off-by: Robert Marko <robimarko@gmail.com>

openwrt-keyring: fix missing 24.10 usign key by installing it

@KA2107 reported that opkg is not able to verify the artifact signatures
produced by buildbot using the usign 24.10 release keys. So lets fix it
by actually adding the 24.10 usign key with d310c6f2833e97f7 fingerprint
into the openwrt-keyring package.

Fixes: #16850
Reported-by: @KA2107
Fixes: a535cfc09e1c ("openwrt-keyring: add OpenWrt 24.10 release build usign key")
References: 2d03f27f0f07 ("openwrt-keyring: make opkg use 22.03 usign key")
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [commit description]

kernel: KERNEL_NET_L3_MASTER_DEV default to y if !SMALL_FLASH

Follow-up for 45d541bb409355f090b971d96ebebd8610ef84a7

This change allows features such as kmod-vrf

```
KERNEL_NET_L3_MASTER_DEV=n

x86_64 generic
bzImage 6,927,360 bytes
aarch64 coretex-a53
kernel  4,268,836 bytes

KERNEL_NET_L3_MASTER_DEV=y

x86_64 generic
bzImage 6,931,456 bytes
aarch64 coretex-a53
kernel  4,273,042 bytes

Delta:
x86_64 generic
+4096 bytes
aarch64 coretex-a53
+4206 bytes

x86_64 generic vrf.ko - 258,792 bytes
aarch64 coretex-a53 vrf.ko - 263,632 bytes
```

See:
https://forum.openwrt.org/t/vrf-support-testing-out-evpn-at-home/181108
https://forum.openwrt.org/t/please-enable-net-l3-master-dev-in-kernel-build-by-default/201825

Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16819
Signed-off-by: Robert Marko <robimarko@gmail.com>

bcm27xx-gpu-fw: fix package

Install definition was accidentally removed in 7afdbc0955a5 and IB fails.

Fixes: 7afdbc0955a5 ("bcm27xx-gpu-fw: update to latest version")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit efd1ec51a1)

mediatek: mt7988: fix peripheral SPI busses

The clocks for SPI busses were named wrongly which resulted in the
spi-mt65xx driver not requesting them. This has apparently been
worked around by marking the clocks required for SPI0 which is used
for SPI-NOR and SPI-NAND flash chips as critical.
Fix the device tree for all 3 generic SPI host controllers and no
longer mark clocks as critical.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 2b173ab730897f53539cab39e87e2b4638cb482a)

openwrt-keyring: add OpenWrt 24.10 release build usign key

 fbae29d730f8 usign: add OpenWrt 24.10 release build public key

Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit a535cfc09e1ced5785d65bee0a0116a71585128e)

OpenWrt v24.10: set branch defaults

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>

ath79: Really fix 5GHz on QCA9886 variant of ZTE MF286

Fix in commit 25eead21c5ab ("ath79: fix 5GHz on QCA9886 variant of ZTE MF286")
was incomplete. A user of such variant popped up, and in the boot log
after installation, we discovered that QCA9886 expects different
pre-calibration data size, than the older QCA9880 variant:

ath10k_pci 0000:00:00.0: qca9888 hw2.0 target 0x01000000 chip_id 0x00000000 sub 0000:0000
ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
ath10k_pci 0000:00:00.0: firmware ver 10.4b-ct-9888-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 59e741e7
ath10k_pci 0000:00:00.0: invalid calibration data length in nvmem-cell 'pre-calibration': 2116 != 12064
ath10k_pci 0000:00:00.0: Loading BDF type 0
ath10k_pci 0000:00:00.0: failed to fetch board data for bus=pci,vendor=168c,device=0056,subsystem-vendor=0000,subsystem-device=0000 from ath10k/QCA9888/hw2.0/board-2.bin
ath10k_pci 0000:00:00.0: failed to fetch board-2.bin or board.bin from ath10k/QCA9888/hw2.0
ath10k_pci 0000:00:00.0: failed to fetch board file: -12
ath10k_pci 0000:00:00.0: could not probe fw (-12)

Explicitly define a pre-calibration nvmem-cell for this variant, and use
it instead of the calibration one, which is shorter.

Fixes: 25eead21c5ab ("ath79: fix 5GHz on QCA9886 variant of ZTE MF286")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16809
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

bcm27xx: update to latest RPi patches

The patches were generated from the RPi repo with the following command:
git format-patch v6.6.58..rpi-6.6.y

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

bcm27xx-gpu-fw: update to latest version

Use release tar instead of downloading separate files.

Full changelog: https://github.com/raspberrypi/firmware/compare/1.20240424...1.20241008

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

ramips: m4r v4: fix typo

It should be debounce-interval, as with the others.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16802
Signed-off-by: Robert Marko <robimarko@gmail.com>

CI: labeler: add bcm27xx-utils

bcm27xx-utils can only be built for bcm27xx target.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

bcm27xx-utils: update to latest version

Fixes build with GCC 14.

Full changelog: https://github.com/raspberrypi/utils/compare/451b9881b72cb994c102724b5a7d9b93f97dc315...6a2a6becebbc38fde34a94386457ac8210f9119b

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

ipq806x: Revert "ipq806x: swap lan leds for Meraki MR52"

This reverts commit ec8f647d168fa8f3b1eedd9b5fe665f793f3a659, as with the
current kernel version, the change actually causes the same bug it once
may have fixed -- that is, the leds are now again reversed.

I suspect this was due to a switch to a newer kernel version between when
the patch was submitted and now reversing the order of the interfaces, so
that eth0 / the LAN interface is also the interface used for PoE, and eth1
/ the WAN interface is the non-PoE interface.

Signed-off-by: Rafal Boni <rafal.boni@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16779
Signed-off-by: Robert Marko <robimarko@gmail.com>

ramips: ignore errors from trx utility

Ignore errors from trx utility to handle case with image too big.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>

image: ignore errors from more commands

Ignore errors in more image commands to handle case where the image is
too big and check-image validation fails.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>

imagebuilder: fix copying of missing kernel/libc

Those packages were not copied due to OPKG using an underscore while APK
uses dashes. Remove that char to copy kernel/libc for either APK/OPKG.

Signed-off-by: Paul Spooren <mail@aparcar.org>

image: ignore errors from mktplinkfw command

Rework tplink-v2-header and tplink-v2-image Build define to ignore error
if mktplinkfw2 errors out.

This is to handle situation when the image is too big and can't be
generated or prev check-image calls deleted the source file as it's too
big.

This aligns to the pattern used by tplink-v1-image.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>

build: correctly ignore Initramfs image on error

Correctly ignore Initramfs image copy on error. This follows the pattern with
sysupgrade image where an image might fail as it's too big or the
generation command fails and there is nothing to copy to the bin
directory.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>

mxs: drop removal of firewall4 package

Drop removal of firewall4 package for I2SE Duckbill device.

With OPKG the firewall4 package was installed anyway as it's a
dependency of luci-app-firewall and was silently installed again later
in such condition. Drop it to fix support for APK.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>

mvebu: cortexa9: drop removal of firewall4 package

Drop removal of firewall4 package for Synology DS213j device.

With OPKG the firewall4 package was installed anyway as it's a
dependency of luci-app-firewall and was silently installed again later
in such condition. Drop it to fix support for APK.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>