Jonas Gorski [Mon, 29 Apr 2013 15:40:21 +0000 (15:40 +0000)]
toolchain: gcc: backport fixes for gcc bug 54295
Fix "Widening multiply-accumulate operation uses wrong value extension"
for 4.7, 4.7-linaro and 4.6-linaro, which backported the broken code to 4.6.
Vanilla 4.6 is unaffected.
Fixes #13420.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 36486
Mirko Vogt [Mon, 29 Apr 2013 02:17:02 +0000 (02:17 +0000)]
move packages related to telephony into its own feed
remove telephony related packages from packages.svn
and add new feed 'telephony.git' to feeds.conf.default
SVN-Revision: 36485
Hauke Mehrtens [Sun, 28 Apr 2013 21:11:17 +0000 (21:11 +0000)]
broadcom-diag: support for the WNDR3700v3
I recently picked up a WNDR3700 to put OpenWRT on, and only after tearing into the box did I find it
was one of the v3 boards, with poor OpenWRT support. This patch should add the board detection and
LED/button control to the broadcom-diag module, and should generate a netgear .chk image that the
bootloader and stock firmware will accept.
The changes to the broadcom-diag module are more than a few lines because the WNDR3700v3 is driving
its LEDs through an HC164 8-bit shift register.
Signed-off-by: Owen Kirby <osk@exegin.com>
SVN-Revision: 36482
Hauke Mehrtens [Sun, 28 Apr 2013 18:53:20 +0000 (18:53 +0000)]
acx-mac80211: make it compile with recent mac80211 again
SVN-Revision: 36481
Hauke Mehrtens [Sun, 28 Apr 2013 18:25:16 +0000 (18:25 +0000)]
brcm47xx: use kernel 3.8.10 as default kernel
The biggest change with this kernel is a new partition parser.
SVN-Revision: 36480
Hauke Mehrtens [Sun, 28 Apr 2013 18:21:34 +0000 (18:21 +0000)]
broadcom-wl: read channel using wlc on detect
Hardcoding channel number to 11 is a bad idea, it may be even not
available on some devices. If there are two single-band radios, the
one for 5GHz doesn't have 11 channel.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 36479
Hauke Mehrtens [Sun, 28 Apr 2013 18:19:31 +0000 (18:19 +0000)]
brcm47xx: add board detection for NETGEAR WNDR4500 V2
SVN-Revision: 36478
Hauke Mehrtens [Sun, 28 Apr 2013 17:59:24 +0000 (17:59 +0000)]
mac80211: brcmsmac: remove initial support for core rev 28
To add support for core rev 28 there are a lot more changes needed.
SVN-Revision: 36477
Hauke Mehrtens [Sun, 28 Apr 2013 17:57:30 +0000 (17:57 +0000)]
mac80211: b43: only use gpio 0 and 1 for the wifi led
sometimes b43 truned the gpio for the switch reset on.
SVN-Revision: 36476
Hauke Mehrtens [Sun, 28 Apr 2013 17:01:56 +0000 (17:01 +0000)]
kernel: fix a memory leak in split_rootfs_data()
allocate_partition() copies all the content of dpart into a new struct.
SVN-Revision: 36475
Hauke Mehrtens [Sun, 28 Apr 2013 16:55:53 +0000 (16:55 +0000)]
mac80211: b43: Handle DMA RX descriptor underrun
SVN-Revision: 36474
Hauke Mehrtens [Sun, 28 Apr 2013 16:52:11 +0000 (16:52 +0000)]
kernel: update bcma and ssb for kernel 3.8+ to version from wireless-testing master-2013-04-26.
SVN-Revision: 36473
Jo-Philipp Wich [Sun, 28 Apr 2013 14:04:39 +0000 (14:04 +0000)]
iwinfo: fix iwinfo_hardware() return value if chip id is not found
SVN-Revision: 36471
Jonas Gorski [Sun, 28 Apr 2013 11:55:23 +0000 (11:55 +0000)]
kernel: update linux 3.9 patches to rc8
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 36469
Jonas Gorski [Sun, 28 Apr 2013 11:10:42 +0000 (11:10 +0000)]
kernel: add missing bcma defines and header file for bcrmfmac
Fixes build failure when having kmod-mmc and brcmfmac selected.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 36468
Felix Fietkau [Sat, 27 Apr 2013 09:56:18 +0000 (09:56 +0000)]
ath9k: fix keycache handling with many connected clients
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 36467
Felix Fietkau [Sat, 27 Apr 2013 09:56:14 +0000 (09:56 +0000)]
mac80211: refresh patch
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 36466
Jo-Philipp Wich [Sat, 27 Apr 2013 09:28:40 +0000 (09:28 +0000)]
netifd: update to git head - disables multicast snooping by default on bridges
SVN-Revision: 36463
Gabor Juhos [Fri, 26 Apr 2013 17:00:54 +0000 (17:00 +0000)]
ar71xx: add user-space support for WNR2000v3
Signed-off-by: Mathieu Olivari <mathieu.olivari@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36461
Gabor Juhos [Fri, 26 Apr 2013 17:00:53 +0000 (17:00 +0000)]
ar71xx: add profile and build image for WNR2000v3
Signed-off-by: Mathieu Olivari <mathieu.olivari@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36460
Gabor Juhos [Fri, 26 Apr 2013 17:00:52 +0000 (17:00 +0000)]
ar71xx: Add Netgear WNR2000v3 support
Network connectivity works fine (LAN and WAN).
For GPIOs, only pwr led and the green wan leds are supported for now.
Signed-off-by: Mathieu Olivari <mathieu.olivari@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36459
Gabor Juhos [Fri, 26 Apr 2013 17:00:50 +0000 (17:00 +0000)]
ar71xx: add profile and build image for the TL-WR720N v3 board
Signed-off-by: yousong <yszhou4tech@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36458
Gabor Juhos [Fri, 26 Apr 2013 17:00:49 +0000 (17:00 +0000)]
ar71xx: add user-space support for the TL-WR720N v3 board
Signed-off-by: yousong <yszhou4tech@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36457
Gabor Juhos [Fri, 26 Apr 2013 17:00:48 +0000 (17:00 +0000)]
ar71xx: add kernel support for TPLINK WR720N v3
Add support for TPLINK WR720N v3 which has 4MB flash,
32MB ram, 2 ethernet interfaces, 1 USB 2.0 port.
The patch is mostly a modification from mach-tl-wr703n.c.
GPIO numbers for the slider switch is from mach-tl-mr3020n.c.
Tested on my device and they worked fine.
Signed-off-by: yousong <yszhou4tech@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36456
Gabor Juhos [Fri, 26 Apr 2013 17:00:47 +0000 (17:00 +0000)]
firmware-utils/mktplinkfw: add support for the TL-WR720N v3 board
Signed-off-by: yousong <yszhou4tech@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36455
Gabor Juhos [Fri, 26 Apr 2013 16:57:43 +0000 (16:57 +0000)]
mpc85xx: Add subtargets Generic and P1020
Only difference between Generic and P1020 is that P1020
enables SMP with two CPUs in the kernel config.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36454
Gabor Juhos [Fri, 26 Apr 2013 16:55:42 +0000 (16:55 +0000)]
kernel: update linux 3.8 to 3.8.9
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36453
Gabor Juhos [Fri, 26 Apr 2013 16:55:40 +0000 (16:55 +0000)]
at91: upgrade to kernel 3.8.7 and use devicetree
This upgrades the AT91 target to 3.8.7, and migrates to device tree.
This allows a single kernel to be built for most at91 variants which
simplifies things quite a bit. The immediate result is that all
subtargets are nuked, and any boards without dts files are no longer
supported, though the target now includes more boards than before. The
adc driver was also nuked as 3.8.7 includes a new one under the IIO
subsystem.
Signed-off-by: Adam Porter <porter.adam@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36452
Gabor Juhos [Fri, 26 Apr 2013 16:55:28 +0000 (16:55 +0000)]
ramips: rt3883: fix build error
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36451
Jo-Philipp Wich [Fri, 26 Apr 2013 13:21:01 +0000 (13:21 +0000)]
iwinfo: add hw database file
SVN-Revision: 36450
Jo-Philipp Wich [Fri, 26 Apr 2013 13:20:15 +0000 (13:20 +0000)]
iwinfo: move builtin hardware database to /usr/share/libiwinfo/hardware.txt
SVN-Revision: 36449
Felix Fietkau [Fri, 26 Apr 2013 10:52:03 +0000 (10:52 +0000)]
mac80211: update to wireless-testing 2013-04-16 + backports
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 36448
John Crispin [Thu, 25 Apr 2013 19:51:08 +0000 (19:51 +0000)]
procd: fix wrap around bug in logread time handling code
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36447
John Crispin [Thu, 25 Apr 2013 19:16:54 +0000 (19:16 +0000)]
hotplug2: make it depend on !PROCD_INIT
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36446
John Crispin [Thu, 25 Apr 2013 19:03:41 +0000 (19:03 +0000)]
lantiq: make leds and network work on VG3503J
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36445
John Crispin [Thu, 25 Apr 2013 19:03:37 +0000 (19:03 +0000)]
lantiq: fix board detection helpers
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36444
John Crispin [Thu, 25 Apr 2013 19:03:32 +0000 (19:03 +0000)]
lantiq: move dts files to thir own folder
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36443
John Crispin [Thu, 25 Apr 2013 19:03:29 +0000 (19:03 +0000)]
generic: fix rtl8366_smi compile warning
drivers/net/phy/rtl8366_smi.c: In function 'rtl8366_sw_set_vlan_ports':
drivers/net/phy/rtl8366_smi.c:1125:6: warning: 'pvid' may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36442
John Crispin [Thu, 25 Apr 2013 19:03:25 +0000 (19:03 +0000)]
lantiq: disable sw portmaps on xrx200 ethernet as segment solation does not work yet
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36441
John Crispin [Thu, 25 Apr 2013 19:03:21 +0000 (19:03 +0000)]
lantiq: make lzma-loader based images for VG3503J
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36440
John Crispin [Thu, 25 Apr 2013 19:03:17 +0000 (19:03 +0000)]
lantiq: update VG3503J.dts to match new partition layout
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36439
John Crispin [Thu, 25 Apr 2013 19:03:13 +0000 (19:03 +0000)]
lantiq: add lzma-loader source
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36438
John Crispin [Thu, 25 Apr 2013 19:03:09 +0000 (19:03 +0000)]
ramips: add profile for Dlink DIR-615 H1
Hello,
this adds the profile for Dlink DIR-615 H1 without the usb default packages
since this router does not have a usb port and while all the needed definitions
for building are already in target/linux/ramips/image/Makefile this also allows
users to select the exact target in RT305x based boards menuconfig for this router
and compile its firmware.
Signed-off-by: Daniel Petre <dani@ip6.ro>
Patchwork: http://patchwork.openwrt.org/patch/3529/
Acked-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36437
John Crispin [Thu, 25 Apr 2013 19:03:05 +0000 (19:03 +0000)]
ramips: remove now unneeded user-space board detection
Now that ALL5002 and ALL5003 each got their own DTS and board names, remove
the now no longer needed user-space part which previously differentiated between
ALL5002 and ALL5003.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
Patchwork: http://patchwork.openwrt.org/patch/3558/
Acked-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36436
John Crispin [Thu, 25 Apr 2013 19:03:01 +0000 (19:03 +0000)]
ramips: introduce DTS for ALL5003
Prior to the switch to 3.8, ALL5002 and ALL5003 boards shared mach-all5002.c.
With the change to DTS, this is no longer accurate, as ALL5002 is based on
Rt3352 SoC while ALL5003 is based on Rt5350 SoC, therefore the corresponding
rt5350.dtsi need to be included for ALL5003.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
Patchwork: http://patchwork.openwrt.org/patch/3557/
Acked-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36435
John Crispin [Thu, 25 Apr 2013 19:02:57 +0000 (19:02 +0000)]
ramips: set preinit interface to eth0 by default.
This makes any ramips device accessible via ethernet in failsafe mode.
Based on: https://dev.openwrt.org/changeset/36322
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3567/
Acked-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36434
John Crispin [Thu, 25 Apr 2013 19:02:53 +0000 (19:02 +0000)]
ramips: Add Alpha ASL-26555 support.
This board uses a TrendChip SOC with its own RAM/Flash for ADSL support.
We know both SOCs are connected through ethernet and use some kind of protocol for UART communication, but due to the lack of GPL sources we couldn't get it to work. For this reason the network is configured only for LAN.
There are two versions (Chile 8MB and Spain 16MB).
Wiki: http://wiki.openwrt.org/toh/alpha/asl26555
Signed-off-by: Esteban Benito <estebanjbs@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3571/
Acked-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36433
John Crispin [Thu, 25 Apr 2013 19:02:48 +0000 (19:02 +0000)]
ramips: Add support of D-link DIR-620D1
Signed-off-by: Serge Vasilugin <vasilugin@yandex.ru>
Acked-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36432
John Crispin [Thu, 25 Apr 2013 19:02:42 +0000 (19:02 +0000)]
ramips: sync kernel patches with the mips-next tree
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36431
John Crispin [Thu, 25 Apr 2013 19:02:37 +0000 (19:02 +0000)]
preinit: move cmdline failsafe= handling ot the generic code
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36430
John Crispin [Thu, 25 Apr 2013 19:02:32 +0000 (19:02 +0000)]
mount_root: prepare base-files
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36429
John Crispin [Thu, 25 Apr 2013 19:02:28 +0000 (19:02 +0000)]
boot: make use of kmodloader if it is available
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36428
John Crispin [Thu, 25 Apr 2013 19:02:24 +0000 (19:02 +0000)]
ubox: add ubox package
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36427
John Crispin [Thu, 25 Apr 2013 19:02:20 +0000 (19:02 +0000)]
procd: update to latest git version
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36426
Felix Fietkau [Thu, 25 Apr 2013 16:28:19 +0000 (16:28 +0000)]
netifd: update to the latest version, fixes interface reload issues when removing the ifname option
SVN-Revision: 36424
Steven Barth [Wed, 24 Apr 2013 18:22:08 +0000 (18:22 +0000)]
6relayd: Fix generation of RA-messages
SVN-Revision: 36419
Jo-Philipp Wich [Wed, 24 Apr 2013 14:44:20 +0000 (14:44 +0000)]
iwinfo: add SR71-15 radio info, fix nl80211 channel/frequency reporting on some architectures
SVN-Revision: 36417
Steven Barth [Wed, 24 Apr 2013 14:17:24 +0000 (14:17 +0000)]
firewall3: Make IPv6 ULA-Border generation dynamic
This fixes working behind another router which gives out ULAs.
SVN-Revision: 36416
Jo-Philipp Wich [Wed, 24 Apr 2013 09:49:09 +0000 (09:49 +0000)]
Enable hidraw support.
It's needed for dealing with certain UART-to-USB adapters built into
e.g. weather stations, and increases the hid module package only
slightly (e.g. on ar71xx: 35k -> 37k).
Signed-off-by: Danny Baumann <dannybaumann@web.de>
SVN-Revision: 36415
Jo-Philipp Wich [Wed, 24 Apr 2013 09:49:03 +0000 (09:49 +0000)]
Add kernel module package for hid-generic driver.
Needed to support e.g. keyboards and mice.
Signed-off-by: Danny Baumann <dannybaumann@web.de>
SVN-Revision: 36414
Steven Barth [Wed, 24 Apr 2013 07:21:42 +0000 (07:21 +0000)]
6relayd: update package description
SVN-Revision: 36413
Steven Barth [Wed, 24 Apr 2013 05:55:39 +0000 (05:55 +0000)]
dnsmasq: update to 2.66 Thanks to Christoph König for patches.
SVN-Revision: 36412
Steven Barth [Wed, 24 Apr 2013 05:02:45 +0000 (05:02 +0000)]
odhcp6c: Set default SOL_MAX_RT to 1h
SVN-Revision: 36411
Felix Fietkau [Tue, 23 Apr 2013 18:35:50 +0000 (18:35 +0000)]
hostapd: return the frequency to some ubus calls to make integration easier
SVN-Revision: 36410
Felix Fietkau [Tue, 23 Apr 2013 16:32:24 +0000 (16:32 +0000)]
mac80211: use the original mac address for the first virtual interface
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 36408
Jonas Gorski [Tue, 23 Apr 2013 13:55:36 +0000 (13:55 +0000)]
bcm63xx: update patches with upstream submissions
SVN-Revision: 36407
Jonas Gorski [Tue, 23 Apr 2013 13:55:17 +0000 (13:55 +0000)]
bcm63xx: switch to linux 3.8
SVN-Revision: 36406
Jo-Philipp Wich [Tue, 23 Apr 2013 10:37:23 +0000 (10:37 +0000)]
lldpd: upgrade to 0.7.1
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
SVN-Revision: 36401
Jo-Philipp Wich [Tue, 23 Apr 2013 10:29:49 +0000 (10:29 +0000)]
gettext-full: updated to 0.18.2.1
Signed-off-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 36400
Jo-Philipp Wich [Tue, 23 Apr 2013 10:29:45 +0000 (10:29 +0000)]
libevent2: update to 2.0.21
Signed-off-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 36399
Jo-Philipp Wich [Tue, 23 Apr 2013 10:29:42 +0000 (10:29 +0000)]
libmnl: update to 1.0.3
Signed-off-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 36398
Jo-Philipp Wich [Tue, 23 Apr 2013 10:29:38 +0000 (10:29 +0000)]
libnetfilter-conntrack: update to 1.0.3
Signed-off-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 36397
Jonas Gorski [Tue, 23 Apr 2013 09:22:02 +0000 (09:22 +0000)]
polarssl: update to 1.2.6
Signed-off-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 36396
Jonas Gorski [Tue, 23 Apr 2013 09:21:59 +0000 (09:21 +0000)]
ncurses: update to 5.9
Signed-off-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 36395
Jonas Gorski [Tue, 23 Apr 2013 09:21:57 +0000 (09:21 +0000)]
libnl: update to 3.2.21
Signed-off-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 36394
Jonas Gorski [Tue, 23 Apr 2013 09:21:55 +0000 (09:21 +0000)]
kernel: add kmod-mcp23s08 package
Package up the Microchip MCP23S08 I/O expander driver. Needed on the
CalAmp LMU5000 board.
Signed-off-by: Adam Porter <porter.adam@gmail.com>
[jogo@openwrt.org: fix subject]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 36393
Steven Barth [Mon, 22 Apr 2013 19:40:16 +0000 (19:40 +0000)]
Change default IPv6 config to enable DHCPv6-PD
SVN-Revision: 36384
Steven Barth [Mon, 22 Apr 2013 19:40:06 +0000 (19:40 +0000)]
netifd: Improve IPv6-ULA assignment handling
SVN-Revision: 36383
Steven Barth [Mon, 22 Apr 2013 19:40:01 +0000 (19:40 +0000)]
odhcp6c: Several fixes and improvements * Add preliminary support for RFC 6603 prefix exclusion * Fix reconfigure-support and reconfigure authentication * Set maximum retransmission timeout for solicitations to 2h * Fix a segfault when parsing IA_PD in advertise messages
SVN-Revision: 36382
Steven Barth [Mon, 22 Apr 2013 19:39:55 +0000 (19:39 +0000)]
6relayd: Add DHCPv6-PD server support, fix relaying in stateful mode
SVN-Revision: 36381
Felix Fietkau [Mon, 22 Apr 2013 15:01:36 +0000 (15:01 +0000)]
kernel: allow __netdev_alloc_skb_ip_align to be called with dev = NULL
SVN-Revision: 36378
Jo-Philipp Wich [Mon, 22 Apr 2013 14:52:28 +0000 (14:52 +0000)]
uci: update to git head
- fixes memory leak in libuci when trying to open not existing configurations
- fixes memory leak in libuci-lua when querying not existing sections or options
- fixes handling of filenames with leading underscore
SVN-Revision: 36377
Felix Fietkau [Mon, 22 Apr 2013 13:24:48 +0000 (13:24 +0000)]
hostapd: update to 2013-04-05
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 36376
Felix Fietkau [Mon, 22 Apr 2013 12:53:32 +0000 (12:53 +0000)]
scripts/config: warn on deprected "depends" syntax instead of throwing a syntax error
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 36375
Felix Fietkau [Mon, 22 Apr 2013 12:53:21 +0000 (12:53 +0000)]
ar71xx: merge more unaligned access hacks from cerowrt-next
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 36374
Jo-Philipp Wich [Sat, 20 Apr 2013 13:01:56 +0000 (13:01 +0000)]
feeds: fix syntax error
SVN-Revision: 36370
Jo-Philipp Wich [Sat, 20 Apr 2013 12:56:52 +0000 (12:56 +0000)]
feeds: add openwrt-routing feed and drop bmx6 feed which got merged into openwrt-routing
SVN-Revision: 36368
Felix Fietkau [Fri, 19 Apr 2013 12:39:40 +0000 (12:39 +0000)]
kernel: backport SSB/BCMA changes in preparation for a compat-wireless update
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 36367
Gabor Juhos [Fri, 19 Apr 2013 08:07:38 +0000 (08:07 +0000)]
linux/3.9: add missing config symbol
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36365
Gabor Juhos [Fri, 19 Apr 2013 08:07:37 +0000 (08:07 +0000)]
linux/3.[89]: update bridge_remove_ipv6_dependency patch
Fixes the following warning:
CC [M] net/ipv6/addrconf.o
net/ipv6/addrconf.c: In function 'addrconf_init':
net/ipv6/addrconf.c:4944:2: warning: assignment from incompatible pointer type [enabled by default]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36364
Gabor Juhos [Fri, 19 Apr 2013 08:07:34 +0000 (08:07 +0000)]
kernel: update linux 3.8 to 3.8.8
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36363
Felix Fietkau [Thu, 18 Apr 2013 13:51:16 +0000 (13:51 +0000)]
build: fix make defconfig
SVN-Revision: 36362
Felix Fietkau [Thu, 18 Apr 2013 12:05:16 +0000 (12:05 +0000)]
build: add new menuconfig code based on linux 3.9
SVN-Revision: 36361
Felix Fietkau [Thu, 18 Apr 2013 12:05:08 +0000 (12:05 +0000)]
toolchain: get rid of libc implementation symbol overloading
SVN-Revision: 36360
Felix Fietkau [Thu, 18 Apr 2013 12:05:02 +0000 (12:05 +0000)]
toolchain: get rid of musl version kconfig symbol overloading
SVN-Revision: 36359
Felix Fietkau [Thu, 18 Apr 2013 12:04:55 +0000 (12:04 +0000)]
toolchain: get rid of eglibc version kconfig symbol overloading
SVN-Revision: 36358
Felix Fietkau [Thu, 18 Apr 2013 12:04:48 +0000 (12:04 +0000)]
toolchain: get rid of uclibc version kconfig symbol overloading
SVN-Revision: 36356
Felix Fietkau [Thu, 18 Apr 2013 12:04:40 +0000 (12:04 +0000)]
toolchain: get rid of gcc kconfig symbol overloading
SVN-Revision: 36355
Felix Fietkau [Wed, 17 Apr 2013 15:36:57 +0000 (15:36 +0000)]
mac80211: rework mac address allocation
If the first byte is available in the address mask, use only that one -
set the local bit and xor it with the id << 2. This ensures that there
are no hardware BSSID & BSSID-mask conflicts with devices that have
almost the same MAC address with just a small offset. The MAC address
conflict has been observed in a deployment with some devices from the
same batch when running with multiple interfaces.
If only some bits of the last byte are available, xor the id onto the
last MAC address byte (relevant mostly for Ralink devices).
In other cases (should not happen at this point), use the previous MAC
address offset calculation but without the local bit.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 36353
Felix Fietkau [Wed, 17 Apr 2013 15:36:49 +0000 (15:36 +0000)]
build: add a CONFIG_MODULES symbol for compatibility with kernel menuconfig
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 36352
projects / openwrt / staging / blocktrron.git / log