Zoltan Herpai [Sat, 11 Jan 2014 21:58:29 +0000 (21:58 +0000)]
sunxi: various changes - let LBDAF be set by generic config - add high-speed timer support - refresh sun5i USB patch
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 39223
Zoltan Herpai [Sat, 11 Jan 2014 17:19:04 +0000 (17:19 +0000)]
sunxi: add support for Olinuxino A10 LIME
Signed-off-by: Zalan Blenessy <zalan.blenessy@gmail.com>
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 39222
Zoltan Herpai [Sat, 11 Jan 2014 17:17:17 +0000 (17:17 +0000)]
uboot-sunxi: add support for Olinuxino A10 LIME
Signed-off-by: Zalan Blenessy <zalan.blenessy@gmail.com>
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 39221
Gabor Juhos [Sat, 11 Jan 2014 16:06:37 +0000 (16:06 +0000)]
kernel: update 3.10 to 3.10.26
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39220
Gabor Juhos [Sat, 11 Jan 2014 11:15:30 +0000 (11:15 +0000)]
ar71xx: ag71xx: increase calculated max frame length value
The r39147 commit introduces a regression: at lease on some routers
with ar8216 switch large packets get lost if 802.1q tagged port is
used on the interface connected to the aforementioned switch.
The r39147 changes code in the way so interface is set to accept
packets no longer than max ethernet frame length for a given mtu.
Unfortunately ar8216 has a feature: it sends two additional bytes
as a packet header and those this header needs to be added to the
max frame length. Otherwise long enough packets get lost.
The problem only manuifests itself if interface is used in vlan
tagged mode. If interface is untagged then ar8216's header fits
into space used by 802.1q tag and not packets are lost.
Include two additional bytes in the max frame length calculation
to fix the issue.
This patch is tested and works with Trendnet TEW-632BRP.
Signed-off-by Nikolay Martynov <mar.kolya@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4656/
[juhosg:
- simplify the patch to include the additional bytes of the
switch header unconditionally,
- change subject and update commit message]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39219
Zoltan Herpai [Fri, 10 Jan 2014 10:47:41 +0000 (10:47 +0000)]
sunxi: add/refresh patches for cubieboard2
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 39218
Gabor Juhos [Fri, 10 Jan 2014 09:37:59 +0000 (09:37 +0000)]
ar71xx: my net n750: simplify LNA GPIO setup
Use the ath79_wmac_set_ext_lna_gpio helper instead
of exporting the GPIOs.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39217
Gabor Juhos [Fri, 10 Jan 2014 09:37:58 +0000 (09:37 +0000)]
ar71xx: my net n600: simplify LNA GPIO setup
Use the ath79_wmac_set_ext_lna_gpio helper instead
of exporting the GPIOs.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39216
Gabor Juhos [Fri, 10 Jan 2014 09:37:57 +0000 (09:37 +0000)]
ar71xx: add a helper function for external LNA GPIO setup
The built-in wireless MAC of the AR934x SoC can handle
external LNAs and the control signal of the LNAs can be
routed to any GPIO line. Add a helper function which
can be used to configure the GPIO lines.
The helper function will be used for AR934x boards
which are using externel LNAs to improve sensitivity.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39215
Gabor Juhos [Fri, 10 Jan 2014 09:07:12 +0000 (09:07 +0000)]
ar71xx: Fix WD My Net N600 weak signal issue
The LNAs need to be enabled by setting their respective GPIO to high even
though the original firmware's setting sets them to low on initialization.
Obviously the LNAs are then later initialized by the driver on the OEM
firmware. Without this fix the device is mostly "deaf".
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Tested-by: Steven Haigh <netwiz@crc.id.au>
Patchwork: http://patchwork.openwrt.org/patch/4689/
[juhosg:
- remove the GPIO LED changes, the My Net N600 has no yellow LEDs at all,
- change subject and update the commit message]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39214
Gabor Juhos [Fri, 10 Jan 2014 09:07:11 +0000 (09:07 +0000)]
ar71xx: Fix WD My Net N750 weak signal issue
The LNAs need to be enabled by setting their respective GPIO to high even
though the original firmware's setting sets them to low on initialization.
Obviously the LNAs are then later initialized by the driver on the OEM
firmware. Without this fix the device is mostly "deaf".
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4688/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39213
Gabor Juhos [Fri, 10 Jan 2014 09:05:31 +0000 (09:05 +0000)]
ath9k: add workaround for AR9331 USB host controller hang with USB1.1 devices
When wifi radio is reset, some bits in (undocumented) USB registers may
flip. Patch adds setting them after radio reset (channel change, up/down).
With this patch stability of USB1.1 full-speed devices, connected directly
to AR9331 host port (no USB2.0 hub) is improved.
See "ar9331's usb stability issue" OpenWrt forum thread for details:
<https://forum.openwrt.org/viewtopic.php?id=39956>
Based on QCA's Open HAL WAR_USB_DISABLE_PLL_LOCK_DETECT() macro:
<https://github.com/qca/qcamain_open_hal_public/blob/master/hal/ar9300/ar9300_reset.c#L74>
Adapted to Linux mac80211 driver for 8Devices Carambola2 board by Mantas Pucka:
<https://github.com/8devices/carambola2/commit/
b08b59ceb4e7f0bad4c0b17e703e1e5c4e168923>
Ported to latest OpenWrt BB branch and tested on TP-Link TL-WR703N by
Michel Stempin <michel.stempin@wanadoo.fr>.
Signed-off-by: Michel Stempin <michel.stempin@wanadoo.fr>
[juhosg: refresh and clean up the ath9k patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39212
Jo-Philipp Wich [Wed, 8 Jan 2014 22:01:55 +0000 (22:01 +0000)]
jsonpath: make output in non-export mode more shell friendly
SVN-Revision: 39211
Imre Kaloz [Tue, 7 Jan 2014 15:03:55 +0000 (15:03 +0000)]
upgrade the Linaro binutils to 2.24-2013.12
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 39210
Imre Kaloz [Tue, 7 Jan 2014 15:00:33 +0000 (15:00 +0000)]
upgrade Linaro GCC 4.8 to 4.8-2013.12
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 39209
Imre Kaloz [Tue, 7 Jan 2014 12:23:35 +0000 (12:23 +0000)]
add x86_64 target support
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 39208
Imre Kaloz [Tue, 7 Jan 2014 10:21:31 +0000 (10:21 +0000)]
virtualbox emulates the e1000 for a long time now
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 39207
Imre Kaloz [Tue, 7 Jan 2014 10:18:55 +0000 (10:18 +0000)]
move most of the x86 image generation options to the main file
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 39206
Zoltan Herpai [Mon, 6 Jan 2014 23:34:31 +0000 (23:34 +0000)]
sunxi: refresh usb vbus patch
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 39205
Zoltan Herpai [Mon, 6 Jan 2014 21:51:39 +0000 (21:51 +0000)]
sunxi: various fixes - DT: update USB vbus from 3.3v to 5v - emac: add missing free_irq - DT: add emac aliases - DT: fix interrupts on A20 - modules: add watchdog module - don't compile in mac80211 - don't compile in usbnet
Thanks to Hans de Goede, Zalan Blenessy et al.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 39204
Hauke Mehrtens [Sat, 4 Jan 2014 23:46:44 +0000 (23:46 +0000)]
bcm53xx: make the l2x0 L2 cache controller work
This fixes the DMA problems with the Ethernet driver.
This also updates some other parts of the patches.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39203
Hauke Mehrtens [Sat, 4 Jan 2014 18:27:09 +0000 (18:27 +0000)]
bcm53xx: update the ethernet core hacks
The PHY always says there is no link
Instead of doing this dma sync a mdelay does the same trick and it is as unreliable.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39202
Hauke Mehrtens [Sat, 4 Jan 2014 18:25:05 +0000 (18:25 +0000)]
kernel: bgmac: update the driver patches to a version submitted for mainline kernel.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39201
Zoltan Herpai [Sat, 4 Jan 2014 17:33:44 +0000 (17:33 +0000)]
sunxi: emac changes - move emac into module - add into profiles where appropriate
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 39200
Zoltan Herpai [Sat, 4 Jan 2014 16:39:31 +0000 (16:39 +0000)]
sunxi: add sata driver to profiles where appropriate
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 39198
Zoltan Herpai [Sat, 4 Jan 2014 16:30:56 +0000 (16:30 +0000)]
sunxi: add sata driver for sun[47]i
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 39197
Zoltan Herpai [Sat, 4 Jan 2014 13:46:43 +0000 (13:46 +0000)]
sunxi: move sunxi-sid (security ID) off to module
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 39196
Zoltan Herpai [Sat, 4 Jan 2014 12:47:51 +0000 (12:47 +0000)]
sunxi: move rtc off to module
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 39195
Zoltan Herpai [Sat, 4 Jan 2014 11:08:27 +0000 (11:08 +0000)]
sunxi: add the actual mmc driver
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 39194
Zoltan Herpai [Sat, 4 Jan 2014 11:02:16 +0000 (11:02 +0000)]
sunxi: delete a31 reset for now in lack of the mach split
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 39193
Zoltan Herpai [Sat, 4 Jan 2014 10:09:52 +0000 (10:09 +0000)]
add support for pcDuino board
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 39192
Zoltan Herpai [Sat, 4 Jan 2014 10:08:31 +0000 (10:08 +0000)]
update version
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 39191
Zoltan Herpai [Sat, 4 Jan 2014 10:06:17 +0000 (10:06 +0000)]
sunxi: add support for pcDuino board
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 39190
Zoltan Herpai [Sat, 4 Jan 2014 10:02:01 +0000 (10:02 +0000)]
sunxi: add mmc support - add MMC support for sun457i - update kernel config to compile in MMC and ext4 - update kernel cmdline
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 39189
Zoltan Herpai [Sat, 4 Jan 2014 09:55:41 +0000 (09:55 +0000)]
sunxi: various fixes - have Kconfig options ordered - add new olinuxino a13-micro board - various fixes for EHCI
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 39188
Zoltan Herpai [Sat, 4 Jan 2014 09:49:44 +0000 (09:49 +0000)]
sunxi: remove sun6i/7i split for now
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 39187
Zoltan Herpai [Sat, 4 Jan 2014 09:47:50 +0000 (09:47 +0000)]
sunxi: refresh clock framework
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 39186
Jo-Philipp Wich [Thu, 2 Jan 2014 11:55:16 +0000 (11:55 +0000)]
Add jsonpath - a command line utility to extract values from JSON data using XPath-like expressions
SVN-Revision: 39185
Steven Barth [Thu, 2 Jan 2014 11:38:36 +0000 (11:38 +0000)]
6relayd: try to workaround race condition at startup
SVN-Revision: 39184
Felix Fietkau [Tue, 31 Dec 2013 13:09:20 +0000 (13:09 +0000)]
netifd: initialize the switch early at start time and on reload (fixes #13015)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 39183
Luka Perkov [Mon, 30 Dec 2013 23:49:25 +0000 (23:49 +0000)]
ixp4xx: upgrade: don't copy extra binaries
hexdump is already added to new temporary file system while less is not used at
all. While at it, remove some trailing whitespaces.
Signed-off-by: Luka Perkov <luka@openwrt.org>
CC: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 39181
Felix Fietkau [Sun, 29 Dec 2013 02:26:34 +0000 (02:26 +0000)]
netifd: update to the latest version, fixes wireless related segfaults on arm
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 39180
Felix Fietkau [Sat, 28 Dec 2013 15:06:14 +0000 (15:06 +0000)]
uClibc: Fix lookup with DNS search in multi-threaded application.
Signed-off-by: Jiri Slachta <slachta@cesnet.cz>
SVN-Revision: 39179
Felix Fietkau [Sat, 28 Dec 2013 15:06:04 +0000 (15:06 +0000)]
uClibc: make res_init() thread safe
Signed-off-by: Jiri Slachta <slachta@cesnet.cz>
SVN-Revision: 39178
Felix Fietkau [Sat, 28 Dec 2013 15:05:56 +0000 (15:05 +0000)]
uClibc: Fix threaded use of res_ functions.
This patch moves res_init() back above #undef _res. It fixes dns resolving issue in OpenWrt
(uClibc related - OpenWrt ticket #11929). It is a backport from uClibc master.
Further details are there:
http://git.uclibc.org/uClibc/commit/libc/inet/resolv.c?id=
20b69920b299585265eb100d0b67e1097ccb1092
Signed-off-by: Jiri Slachta <slachta@cesnet.cz>
SVN-Revision: 39177
Felix Fietkau [Sat, 28 Dec 2013 14:19:54 +0000 (14:19 +0000)]
netifd: update to the latest version, fixes wifi related segfaults
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 39176
Felix Fietkau [Sat, 28 Dec 2013 11:07:37 +0000 (11:07 +0000)]
hostapd: fix mixed wep/wpa with netifd
Signed-off-by: Catalin Patulea <cat@vv.carleton.ca>
SVN-Revision: 39174
Felix Fietkau [Sat, 28 Dec 2013 11:07:28 +0000 (11:07 +0000)]
hostapd: fix the uci option name for ap isolate
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 39173
John Crispin [Fri, 27 Dec 2013 21:15:31 +0000 (21:15 +0000)]
firmware-utils: check_magic() in buffalo-lib.c always return 0
spotted with cppcheck
Signed-off-by: Etienne CHAMPETIER <etienne.champetier@free.fr>
SVN-Revision: 39171
John Crispin [Fri, 27 Dec 2013 21:15:20 +0000 (21:15 +0000)]
swconfig: remove useless variables, return -1 on errors
spotted with cppcheck
Signed-off-by: Etienne CHAMPETIER <etienne.champetier@free.fr>
SVN-Revision: 39170
John Crispin [Fri, 27 Dec 2013 21:15:09 +0000 (21:15 +0000)]
base-files: fix mount-utils incompatibility
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
SVN-Revision: 39169
John Crispin [Fri, 27 Dec 2013 21:14:49 +0000 (21:14 +0000)]
ralink: fix tso regression in the ethernet driver
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 39168
Hauke Mehrtens [Thu, 26 Dec 2013 23:30:10 +0000 (23:30 +0000)]
brcm47xx: fix cpu wait for BCM4706
This was called to early.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39167
Hauke Mehrtens [Thu, 26 Dec 2013 23:27:52 +0000 (23:27 +0000)]
brcm47xx: b44: This updates the phylib patches to the version send upstream
This uses a fixed phy instead of a dummy one.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39166
Hauke Mehrtens [Thu, 26 Dec 2013 23:22:31 +0000 (23:22 +0000)]
kernel: bgmac: update patches
This updates the bgmac backport patch to the current upstream version
and adds some more patches mostly for BCM4707.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39165
Imre Kaloz [Thu, 26 Dec 2013 22:19:29 +0000 (22:19 +0000)]
handle the Linaro version as well
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 39164
John Crispin [Wed, 25 Dec 2013 17:04:50 +0000 (17:04 +0000)]
ramips: add support for RT-N14U (mt7620n based) board
added dts file and userspace scripts modified to support Asus RT-N14U board
current support status:
usb works
ethernet works
buttons reset, wps
leds asus:blue:[usb|lan|wan|air|power]
i2c not tested
uart not tested
wifi not yet
Signed-off-by: Pavel Löbl <lobl.pavel@gmail.com>
SVN-Revision: 39163
John Crispin [Wed, 25 Dec 2013 17:04:34 +0000 (17:04 +0000)]
ramips: add gpio pin 72 in mt7620 chips to dtsi files
describes register set to control last gpio pin on mt7620 platfrom
Signed-off-by: Pavel Löbl <lobl.pavel@gmail.com>
SVN-Revision: 39162
Gabor Juhos [Mon, 23 Dec 2013 17:05:23 +0000 (17:05 +0000)]
ar71xx: fix max frame length of the QCA955x SoCs
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39161
Gabor Juhos [Mon, 23 Dec 2013 17:05:21 +0000 (17:05 +0000)]
ar71xx: don't set builtin_switch flag for QCA9558
It makes no sense, the SoC has no built-in switch.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39160
Gabor Juhos [Mon, 23 Dec 2013 17:05:19 +0000 (17:05 +0000)]
x86/kvm_guest: remove 3.7 support
Patch-by: Stijn Tintel <stijn@linux-ipv6.be>
Patchwork: http://patchwork.openwrt.org/patch/4637/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39159
Gabor Juhos [Mon, 23 Dec 2013 17:05:18 +0000 (17:05 +0000)]
x86/kvm_guest: remove 3.3 support
Patch-by: Stijn Tintel <stijn@linux-ipv6.be>
Patchwork: http://patchwork.openwrt.org/patch/46366/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39158
Gabor Juhos [Mon, 23 Dec 2013 17:05:16 +0000 (17:05 +0000)]
x86/kvm_guest: add support for 3.10 and switch to it
Patch-by: Stijn Tintel <stijn@linux-ipv6.be>
Patchwork: http://patchwork.openwrt.org/patch/4635/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39157
Felix Fietkau [Mon, 23 Dec 2013 12:11:28 +0000 (12:11 +0000)]
hostapd: fix wep with netifd
Signed-off-by: Catalin Patulea <cat@vv.carleton.ca>
SVN-Revision: 39156
Felix Fietkau [Sat, 21 Dec 2013 19:42:45 +0000 (19:42 +0000)]
wpa_supplicant: fix interface combination parsing issues
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 39155
Jo-Philipp Wich [Sat, 21 Dec 2013 13:47:46 +0000 (13:47 +0000)]
opkg: switch to git repository (#14655)
Upstream development now takes place in a git repository which was clone
from the old svn repository. Switch the source location to the git tree
using the commit that corresponds to the old svn r618 revision.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 39153
Jo-Philipp Wich [Sat, 21 Dec 2013 13:31:28 +0000 (13:31 +0000)]
dnsmasq: rework init procedure
- cache udhcp check results to speed up subsequent reloads
- enable procd file tracking for /var/etc/dnsmasq.conf to only reload service if needed
- implement reload action to only restart dnsmasq if /var/etc/dnsmasq.conf actually changed
- launch dnsmasq from interface hotplug to avoid race conditions with network bringup
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 39152
Imre Kaloz [Fri, 20 Dec 2013 20:25:44 +0000 (20:25 +0000)]
change fixup method and fix CFLAGS handling
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 39151
Felix Fietkau [Fri, 20 Dec 2013 16:02:32 +0000 (16:02 +0000)]
ath9k: merge a timer handling fixes
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 39150
Gabor Juhos [Fri, 20 Dec 2013 11:41:23 +0000 (11:41 +0000)]
ar71xx: allow to use large ethernet frames on AR934x SoCs
The hardware supports large ethernet frames. Override
the maximum frame length and packet lenght mask in the
platform data to allow to use large MTU on the ethernet
interfaces.
Limit the feature to AR934x SoCs for now. It should work
on some other SoCs as well, but those has not been tested
yet.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39149
Gabor Juhos [Fri, 20 Dec 2013 11:41:22 +0000 (11:41 +0000)]
ar71xx: ag71xx: fix max frame length setup of the built-in switches
The currently used bitmask of the maximum frame length field
is wrong for both models. On AR724x/AR933x the largest frame
size is 2047 bytes, on the AR934x it is 16383 bytes.
Make the MTU setup code model specific, and use the correct
bitmask for both models. Also change the value to the maximum.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39148
Gabor Juhos [Fri, 20 Dec 2013 11:41:20 +0000 (11:41 +0000)]
ar71xx: ag71xx: calculate max frame len register value from the MTU
Set the MAX_FRAME_LEN register to zero in ag71xx_hw_init()
and write the correct value into that from the ag71xx_open()
and ag71xx_fast_reset() functions.
Also recalculate the RX buffer size based on the actual
maximum frame length value to optimize memory allocation.
Additionaly, disallow to change the MTU value while the
interface it running.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39147
Gabor Juhos [Fri, 20 Dec 2013 11:41:18 +0000 (11:41 +0000)]
ar71xx: ag71xx: add ag71xx_max_frame_len() helper
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39146
Gabor Juhos [Fri, 20 Dec 2013 11:41:17 +0000 (11:41 +0000)]
ar71xx: ag71xx: get max_frame_len and desc_pktlen_mask from platform data
This will allow to use SoC specific values for both.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39145
Gabor Juhos [Fri, 20 Dec 2013 11:41:16 +0000 (11:41 +0000)]
ar71xx: ag71xx: store descriptor packet length mask in ag71xx struct
The currently used bitmask is not correct for all SoCs.
Introduce a new field in struct ag71xx and store the
bitmask in that. Use the current value for now, it will
be adjusted for each SoCs in further patches.
Aslo use the new field directly in the ag71xx_rx_packets
and ag71xx_hard_start_xmit() functions and remove the
ag71xx_desc_pktlen() helper.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39144
Imre Kaloz [Fri, 20 Dec 2013 06:09:41 +0000 (06:09 +0000)]
handle new libs required for new kernels
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 39142
Imre Kaloz [Fri, 20 Dec 2013 05:50:24 +0000 (05:50 +0000)]
don't fail if there are no dtbs
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 39141
Felix Fietkau [Thu, 19 Dec 2013 17:18:12 +0000 (17:18 +0000)]
ar71xx: add missing tx gain table flag for buffalo wzr-hp-g450h
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 39139
Felix Fietkau [Thu, 19 Dec 2013 17:18:07 +0000 (17:18 +0000)]
ath9k: merge another round of upstream (or -pending) fixes and cleanups
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 39138
Luka Perkov [Thu, 19 Dec 2013 02:03:26 +0000 (02:03 +0000)]
imx6: refresh patches
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 39135
Luka Perkov [Thu, 19 Dec 2013 02:03:25 +0000 (02:03 +0000)]
kernel: backport upstream inet fix
Without it in some occasions oops is shown on network restart. Problem was
noticed on imx6 targed.
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 39134
Luka Perkov [Thu, 19 Dec 2013 02:03:16 +0000 (02:03 +0000)]
imx6: proper fix for io-remap
The previous patch was not the proper fix for PCI devices that require io
resources. The new patch is the proper fix backported from mainline.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 39133
Jo-Philipp Wich [Wed, 18 Dec 2013 15:38:28 +0000 (15:38 +0000)]
procd: fix service file tracking
The instance_config_move() function in the procd instance managing code is
missing a blobmsg_list_move() call to update the tracked file items with the
newly calculated checksums in case of a file change.
Without that change, services are always reloaded after the first change to
a tracked file regardless of whether there are any subsequent changes or not.
Add a missing instance of blobmsg_list_free() as well.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 39132
Jo-Philipp Wich [Wed, 18 Dec 2013 12:38:29 +0000 (12:38 +0000)]
netifd: add reload trigger for /etc/config/wireless as well
SVN-Revision: 39131
Gabor Juhos [Tue, 17 Dec 2013 22:14:13 +0000 (22:14 +0000)]
ar71xx: enable images for WD My Net N750
Now that the switch works correctly we can enable the images for this
board.
Flashing from the factory firmware, the factory failsafe loader and
sysupgrade was tested successfully.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4617/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39130
Gabor Juhos [Tue, 17 Dec 2013 22:14:12 +0000 (22:14 +0000)]
ar71xx: fix WD My Net N750 switch led cfg
Now that the switch is working correctly I had the chance to actually
test the LED config.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4616/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39129
Gabor Juhos [Tue, 17 Dec 2013 22:14:11 +0000 (22:14 +0000)]
ar71xx: implement switch fix for WD My Net N750
The bootloader on the WD My Net N750 disables the ports on it's internal
AR8327N switch by powering them down. The stock firmware then brings the
ports back up again by starting the auto negotiation process on each
port.
This fix implements just that.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4615/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39128
Gabor Juhos [Tue, 17 Dec 2013 22:14:10 +0000 (22:14 +0000)]
ar71xx: implement callback in mdio reset
This enables us to add fixups to the board specific code for boards that
require special treatment of PHYs on mdio bus reset.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
http://patchwork.openwrt.org/patch/4614/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39127
Gabor Juhos [Tue, 17 Dec 2013 22:14:07 +0000 (22:14 +0000)]
ar71xx: make ag71xx_mdio_platform_data visible
This enables us to modify the ag71xx_mdio_platform_data from within the
board support files.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4613/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39126
Felix Fietkau [Tue, 17 Dec 2013 20:37:27 +0000 (20:37 +0000)]
busybox: add back support for top-level menuconfig based config overrides (can be used by custom packages to alter the config)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 39125
Jonas Gorski [Tue, 17 Dec 2013 19:05:03 +0000 (19:05 +0000)]
gpio-button-hotplug: fix crash on remove
Don't call gpio_keys_remove recursively. Setting the platform
data to NULL triggered an oops on the second iteration, so there was
no infinate loop.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39124
Jo-Philipp Wich [Tue, 17 Dec 2013 17:17:00 +0000 (17:17 +0000)]
busybox: restore init scripts
Since the removal of the busybox menuconfig entries, the init scripts
for cron, telnet and ntp are not packaged anymore. Unconditionally
ship them from now on.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 39123
Jo-Philipp Wich [Tue, 17 Dec 2013 16:59:47 +0000 (16:59 +0000)]
firewall: fix handling of tcp_ecn parameter
The firewall3 implementation as well as the shell implementation predating it
used to process the tcp_ecnoption as boolean while it actually is an integer.
Change the code to parse tcp_ecn as integer.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 39122
Gabor Juhos [Tue, 17 Dec 2013 16:27:46 +0000 (16:27 +0000)]
ar71xx: ag71xx: compute the RX buffer size from the maximum frame size
Currently, the AG71XX_RX_PKT_SIZE value limits the received
frame size to 1514/1516 bytes with/without a VLAN header
respectively. However the hardware limit is controlled by
the value the AG71XX_REG_MAC_MFL register which contains
the value of the max_frame_len field.
Compute the RX buffer size from the max_frame_len field
to get rid of the 1514/1516 byte limitation. Also remove
the unused AG71XX_RX_PKT_SIZE definition.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39121
Gabor Juhos [Tue, 17 Dec 2013 16:27:44 +0000 (16:27 +0000)]
ar71xx: ag71xx: store RX buffer size in the ag71xx struct
This allows to change the value dynamically.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39120
Felix Fietkau [Tue, 17 Dec 2013 15:59:29 +0000 (15:59 +0000)]
iproute2: reduce .ipk package size from ~100k down to ~60k
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 39119
Felix Fietkau [Tue, 17 Dec 2013 15:59:25 +0000 (15:59 +0000)]
busybox: disable module utils, kmodloader provides them
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 39118
Gabor Juhos [Tue, 17 Dec 2013 15:18:16 +0000 (15:18 +0000)]
ar71xx: ag71xx: store maximum frame length in the ag71xx struct
This will allow to use different values for the
different SoCs.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39117
Gabor Juhos [Tue, 17 Dec 2013 15:12:52 +0000 (15:12 +0000)]
ar71xx: ag71xx: use mdio bus name in ar7240_probe messages
The ar7240_probe function uses the network device name
in the kernel log messages, however the name is not yet
initialized when the ar7240_probe function is called.
Use the mdio bus name in the messages to avoid ugly
log lines like the following one:
eth%d: Found an AR7240/AR9330 built-in switch
Reported-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39116
Gabor Juhos [Tue, 17 Dec 2013 15:12:50 +0000 (15:12 +0000)]
ag71xx: ag71xx: use device name for debugfs entry
The ag71xx debugfs code uses the network device name
for the device specific debugfs directory. Since r38689
'ar71xx: ag71xx: fix a race involving netdev registration'
the debugfs initialization happens before the ethernet
device gets registered and the network device name contains
'eth%d' at this point. If the board setup code registers
multiple ag71xx devices, the debugfs code tries to create
the device specific dir with the same name which causes
an error like this:
eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=
004dd041, driver=Generic PHY]
ag71xx: probe of ag71xx.0 failed with error -12
Use the device name for the debugfs directory to avoid the
collisions. Also add an error message and change the return
code if the debugfs_create_dir call fails.
Reported-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39115
projects / openwrt / openwrt.git / log