Petr Štetiar [Wed, 11 Mar 2020 11:21:49 +0000 (12:21 +0100)]
imx6: switch to 5.4 kernel
Seems to be working fine, it's 99.9% upstream stuff anyway. Lets start
wider userbase testing.
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Thu, 5 Mar 2020 08:33:52 +0000 (09:33 +0100)]
rpcd: fix respawn settings
Commit
432ec292ccc8 ("rpcd: add respawn param") has introduced infinite
restarting of the service which could be reached over network. This is
not recommended security practice as it might give potential adversary
infinite number of tries in case there might be some issue in the rpcd
or its surrounding stack.
So lets remove the currently bogus `respawn_retry` variable (it wasn't
possible to override it anyway), reverting to the previous default max.
of 5 service restarts which could be now overriden via system's UCI
settings if desired.
Cc: Jo-Philip Wich <jow@mein.io>
Cc: Florian Eckert <fe@dev.tdt.de>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Fixes: 432ec292ccc8 ("rpcd: add respawn param")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Hans Dedecker [Mon, 16 Mar 2020 20:26:33 +0000 (21:26 +0100)]
curl: bump to 7.69.1
For changes in 7.69.1; see https://curl.haxx.se/changes.html#7_69_1
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Álvaro Fernández Rojas [Mon, 16 Mar 2020 19:41:03 +0000 (20:41 +0100)]
bcm27xx: sync 5.4 patches with RPi Foundation
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Rozhuk Ivan [Sat, 16 Nov 2019 02:11:10 +0000 (05:11 +0300)]
wwan: fix hotplug event handling
Hotplug manager send: "remove" -> "add" -> "bind" events,
script interpret bind as "not add" = "remove" and mark device
as unavailable.
Signed-off-by: Rozhuk Ivan <rozhuk.im@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
Rozhuk Ivan [Sat, 16 Nov 2019 02:10:05 +0000 (05:10 +0300)]
comgt: fix hotplug event handling
Hotplug manager send: "remove" -> "add" -> "bind" events,
script interpret bind as "not add" = "remove" and mark device
as unavailable.
Signed-off-by: Rozhuk Ivan <rozhuk.im@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
Hans Dedecker [Mon, 16 Mar 2020 19:56:30 +0000 (20:56 +0100)]
netifd: update to latest git HEAD
dbdef93 interface-ip: transfer prefix route ownership for deprecated ipv6addr to kernel
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Petr Štetiar [Mon, 16 Mar 2020 09:19:19 +0000 (10:19 +0100)]
bcm27xx: switch to 5.4 kernel
Been running it for a few days on RPi0W PMS sensor node and on RPi4.
Lets start wider userbase testing.
Cc: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Yanase Yuki [Mon, 16 Mar 2020 08:42:38 +0000 (17:42 +0900)]
ipq806x: read both WG2600HP MAC addresses from flash
WG2600HP has its WLAN MAC addresses at PRODUCTDATA 0xc and 0x12, so
use them both directly.
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
[commit title/message clarification]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Mon, 16 Mar 2020 15:34:07 +0000 (16:34 +0100)]
ipq806x: remove useless case within default case for upgrade
The default case will catch anything left, there is no need to
explicitly add any device to it.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Kevin Darbyshire-Bryant [Mon, 16 Mar 2020 09:07:36 +0000 (09:07 +0000)]
libnftnl: bump to 1.1.5
Solve missing references to nftnl_set_list_lookup_byname when building
iptables with Nftables support enabled (CONFIG_IPTABLES_NFTABLES)
Bump the ABI version to force everything to match.
/Users/kevin/wrt/staging_dir/toolchain-x86_64_gcc-9.2.0_musl/lib/gcc/x86_64-openwrt-linux-musl/9.2.0/../../../../x86_64-openwrt-linux-musl/bin/ld: xtables_nft_multi-nft-bridge.o: in function `nft_bridge_parse_lookup':
nft-bridge.c:(.text.nft_bridge_parse_lookup+0xcd): undefined reference to `nftnl_set_list_lookup_byname'
/Users/kevin/wrt/staging_dir/toolchain-x86_64_gcc-9.2.0_musl/lib/gcc/x86_64-openwrt-linux-musl/9.2.0/../../../../x86_64-openwrt-linux-musl/bin/ld: xtables_nft_multi-nft-cache.o: in function `nftnl_set_list_cb':
nft-cache.c:(.text.nftnl_set_list_cb+0x80): undefined reference to `nftnl_set_list_lookup_byname'
/Users/kevin/wrt/staging_dir/toolchain-x86_64_gcc-9.2.0_musl/lib/gcc/x86_64-openwrt-linux-musl/9.2.0/../../../../x86_64-openwrt-linux-musl/bin/ld: xtables_nft_multi-nft-cache.o: in function `fetch_set_cache':
nft-cache.c:(.text.fetch_set_cache+0x10a): undefined reference to `nftnl_set_list_lookup_byname'
collect2: error: ld returned 1 exit status
make[6]: *** [xtables-nft-multi] Error 1
make[5]: *** [all] Error 2
make[4]: *** [all-recursive] Error 1
make[3]: *** [all] Error 2
make[2]: *** [/Users/kevin/wrt/build_dir/target-x86_64_musl/linux-x86_64/iptables-1.8.4/.built] Error 2
make[2]: Leaving directory `/Users/kevin/wrt/package/network/utils/iptables'
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Sungbo Eo [Mon, 16 Mar 2020 05:55:40 +0000 (14:55 +0900)]
kernel: make kmod-i2c-mux selected by dependent modules
Currently kmod-i2c-mux-* will not get into images unless kmod-i2c-mux is added
to DEVICE_PACKAGES as well. By changing the dependencies from "depends on" to
"select", we do not have the issue anymore.
Furthermore, we can remove most occurrences of the package from DEVICE_PACKAGES
and similar variables, as it is now pulled by dependent modules such as:
- kmod-i2c-mux-pca954x
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Sungbo Eo [Sun, 15 Mar 2020 17:42:38 +0000 (02:42 +0900)]
oxnas: rework 02_network
Just like other targets do, introduce two setup functions for interfaces and
MAC addresses.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Sungbo Eo [Sun, 15 Mar 2020 11:56:40 +0000 (20:56 +0900)]
oxnas: use dt-bindings macros for GPIO
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Sungbo Eo [Sun, 15 Mar 2020 11:44:05 +0000 (20:44 +0900)]
oxnas: merge Pogoplug V3 DTS patches into one file
As it seeems these patches are for OpenWrt and they are not going to be merged
to mainline, let's merge them to improve maintainability.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Sungbo Eo [Sun, 15 Mar 2020 11:31:30 +0000 (20:31 +0900)]
oxnas: sort kernel configs
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Sungbo Eo [Sun, 15 Mar 2020 11:39:36 +0000 (20:39 +0900)]
oxnas: remove duplicate config options
Remove symbols already covered by generic and target kernel configs.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Sungbo Eo [Sun, 15 Mar 2020 10:35:50 +0000 (19:35 +0900)]
oxnas: use AddDepends in modules.mk
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Sungbo Eo [Sun, 15 Mar 2020 10:33:43 +0000 (19:33 +0900)]
oxnas: harmonize line breaks in ox820.mk
Follow the guideline suggested in
e417ff88f19b ("ramips: harmonize line breaks
in image Makefiles").
While at it, fix typos in the device title of Akitio MyCloud.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Mathias Kresin [Sun, 15 Mar 2020 20:26:23 +0000 (21:26 +0100)]
lantiq: move mux for pins into subnodes
The mux need to be defined in a subnode to be considered by the pinctrl
framework. These muxes aren't set as expected and might cause not
working subsystems.
Fixes: 8e7b573b7aa4 ("lantiq: dts: assign the PCI pins to the PCI controller node")
Fixes: dcb5e52209e5 ("lantiq: dts: assign the STP pins to the STP GPIO controller node")
Fixes: 660200e53d62 ("lantiq: dts: assign the GPHY LED pins to the Ethernet controller node")
Signed-off-by: Mathias Kresin <dev@kresin.me>
Mathias Kresin [Thu, 5 Mar 2020 19:34:27 +0000 (20:34 +0100)]
iproute2: revert add libcap support, enabled in ip-full
This reverts commit
a6da3f9ef746101b84a6f530f5a40de28341b69a.
The libcap isn't as optional as the commit messages suggests. A hard
dependency to the libcap package is added, which is only available in
the external packages feed. Therefore it is impossible to package
ip-full without having the external packages feed up and running, which
is a regression to the former behaviour.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: Hans Dedecker <dedeckeh@gmail.com>
Jo-Philipp Wich [Fri, 13 Mar 2020 14:54:50 +0000 (15:54 +0100)]
pkgconf: always retain -I and -L flags
The pkgconf fork filters -I and -L flag values from .pc files which match
pkgconf's builtin system directory value.
During configure, pkgconf derives the default system include and library
search path values from exec_prefix, which is set to staging_dir/host in
the host tool build phase.
Due to that, pkgconf will drop all -I and -L flags pointing to
staging_dir/host/include or staging_dir/host/lib, unless invoked with
--keep-system-cflags and --keep-system-libs respectively, breaking our
kernel libelf discovery / stack validation workarounds.
In order to inhibit the filtering, add --keep-system-cflags and
--keep-system-libs to our pkg-config shell wrapper.
Fixes: GH#2832
Fixes: 867298cf47 ("tools/pkg-config: Replace with pkgconf")
Ref: https://lists.infradead.org/pipermail/openwrt-devel/2020-March/022182.html
Ref: https://git.openwrt.org/
fe43969336201f2cc7d103b68fd6e65989bee184
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Acked-by: Petr Štetiar <ynezz@true.cz>
Hans Dedecker [Sun, 15 Mar 2020 19:06:12 +0000 (20:06 +0100)]
odhcpd: update to latest git HEAD
6594c6b ubus: use dhcpv6 ia assignment flag
a90cc2e dhcpv6-ia: avoid setting lifetime to infinite for static assignments
bb07fa4 dhcpv4: avoid setting lifetime to infinite for static assignments
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Kevin Darbyshire-Bryant [Tue, 31 Dec 2019 10:55:50 +0000 (10:55 +0000)]
iptables: update to 1.8.4
Bump to iptable 1.8.4 and address packaging issue as mentioned in the
original bump/revert cycle.
"This reverts commit
10cbc896c0a26aecff37261450c21f29fb5b99db.
The updated iptables package does not build due to the following error
encountered on the buildbots:
cp: cannot stat '.../iptables-1.8.4/ipkg-install/usr/lib/libiptc.so.*': No such file or directory
The changelog mentions "build: remove -Wl,--no-as-needed and libiptc.so" so
it appears as if further packaging changes are needed beyond a simple
version bump."
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Robert Marko [Sun, 15 Mar 2020 12:36:40 +0000 (13:36 +0100)]
ipq40xx: 5.4: enable NAND
Lets enable RAW NAND and Qcom NANDC drivers again in kernel 5.4.
They were dropped when 5.4 support was introduced due to upstream
changing the symbol names so refreshing was not enough.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
[cut long line in commit message, enabled BCH as well]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
David Bauer [Sun, 15 Mar 2020 02:36:16 +0000 (03:36 +0100)]
ath79: fix missing watchdog core dependency for hwmon-sch5627
Fixes following error uncovered while building ath79/tiny on 5.4:
Package kmod-hwmon-sch5627 is missing dependencies for the following
libraries:
watchdog.ko
See the similar commit
e546e6252bb1 ("malta: fix missing watchdog core
dependency for hwmon-sch5627") for a detailed explanation.
Signed-off-by: David Bauer <mail@david-bauer.net>
Sungbo Eo [Wed, 11 Mar 2020 17:50:35 +0000 (02:50 +0900)]
mvebu: use generic diag.sh
This commit removes the target-specific diag.sh script. This way, the
generic one is used for the target, which uses DT-aliases to specify the
LEDs used.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Tested-by: Ansuel Smith <ansuelsmth@gmail.com> [wrt3200acm @ 5.4]
David Bauer [Sat, 14 Mar 2020 23:01:38 +0000 (00:01 +0100)]
ath79: add correct phy-mode for QCA9563 boards
The TP-Link RE450 as well as the UniFi AC series missed the phy-mode
property. Because of this, the incorrect MII phy-mode from the root dtsi
was used.
With Kernel 5.4, this leads to problems when used with a AR8033 PHY. The
bootloader seems to leave the fiber pages selected.
As there's not switch to copper pages happening in at803x_config_init
due to the incorrect phy-mode, the new at803x_read_status will interpret
the status of the SGMII side as the status of the copper side.
Signed-off-by: David Bauer <mail@david-bauer.net>
Christian Lamparter [Sat, 7 Mar 2020 15:58:32 +0000 (16:58 +0100)]
apm821xx: 4.14: remove kernel config and patches
This patch removes the 4.14 kernel support from the apm821xx target.
The 4.19 kernel has been available and stable for a while and the 5.4
kernel support has been tested successfully on real hardware as well.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Kevin Darbyshire-Bryant [Fri, 13 Mar 2020 17:56:40 +0000 (17:56 +0000)]
build: fix kernel 5.4 on macos
As part of the kernel build process there are utilities built to run on
the host system that expect linux kernel headers to be available.
Unfortunately macos/darwin doesn't have these headers.
vdso2c requires types.h so provide a minimal stub to satisfy it.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
David Bauer [Fri, 13 Mar 2020 00:07:39 +0000 (01:07 +0100)]
ath79: use downstream ag71xx for Kernel 5.4
The ag71xx driver from Linux 5.4 currently has various shortcomings
when used with OpenWrt compared to our downstream version.
For example, the upstream driver does not support modifying the ethernet
clock and configuring RGMII delays on the MAC side.
While we should certainly switch to the upstream driver, the amount of
necessary patches would make it cumbersome to work with. It's also
highly likely we won't be able to finish patching the upstream driver in
time for a Linux 5.4 release.
Tested on Siemens WS-AP3610.
CC: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Daniel Golle [Fri, 13 Mar 2020 19:06:03 +0000 (20:06 +0100)]
procd: update to latest git HEAD
77a6782 jail: mount-bind /etc/resolv.conf for non-netns jails
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Adrian Schmutzler [Fri, 13 Mar 2020 14:51:30 +0000 (15:51 +0100)]
base-files: convert leading spaces to tabs in functions.sh
Use tabs for indent consistently.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sungbo Eo [Thu, 5 Mar 2020 14:42:18 +0000 (23:42 +0900)]
kernel: make kmod-i2c-core selected by dependent modules
Currently kmod-i2c-* will not get into images unless kmod-i2c-core is added to
DEVICE_PACKAGES as well. By changing the dependencies from "depends on" to
"select", we do not have the issue anymore.
Furthermore, we can remove most occurrences of the package from DEVICE_PACKAGES
and similar variables, as it is now pulled by dependent modules such as:
- kmod-hwmon-lm75
- kmod-i2c-gpio
- kmod-i2c-gpio-custom
- kmod-i2c-mux
- kmod-i2c-ralink
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sungbo Eo [Thu, 5 Mar 2020 14:22:47 +0000 (23:22 +0900)]
kernel: make kmod-hwmon-core selected by dependent modules
Currently kmod-hwmon-* will not get into images unless kmod-hwmon-core is added
to DEVICE_PACKAGES as well. By changing the dependencies from "depends on" to
"select", we do not have the issue anymore.
Furthermore, we can remove most occurrences of the package from DEVICE_PACKAGES
and similar variables, as it is now pulled by dependent modules such as:
- kmod-hwmon-gpiofan
- kmod-hwmon-lm63
- kmod-hwmon-lm75
- kmod-hwmon-lm85
- kmod-hwmon-lm90
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx, adjust line wrapping]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sungbo Eo [Wed, 11 Mar 2020 02:27:59 +0000 (11:27 +0900)]
layerscape: add kmod-i2c-mux to DEVICE_PACKAGES for traverse-ls1043
kmod-i2c-mux-pca954x will not get into images unless kmod-i2c-mux is added to
DEVICE_PACKAGES as well.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Sungbo Eo [Thu, 12 Mar 2020 19:19:32 +0000 (04:19 +0900)]
ramips: add support for TOTOLINK A3
TOTOLINK A3 is a clone of ipTIME A3. The only difference is the model name.
Specifications:
- SoC: MT7628AN
- RAM: DDR2 64MB
- Flash: SPI NOR 8MB
- WiFi:
- 2.4GHz: SoC internal
- 5GHz: MT7612EN
- Ethernet: 3x 10/100Mbps
- Switch: SoC internal
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Tested on device by JasonHCH <hsuan670629@gmail.com>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Jun Su [Tue, 3 Mar 2020 09:33:40 +0000 (17:33 +0800)]
ath79: add support for TP-Link TL-WR740N v5
This adds support for the TP-Link TL-WR740N v5, a clone of the
v4 only with a different TPLINK_HWID. It was already supported
in ar71xx as well.
Specifications:
SOC: Atheros AR9331
CPU: 400MHz
Flash: 4 MiB
RAM: 32 MiB
WLAN: Atheros AR9330 bgn
Ethernet: 5 ports (100M)
Flashing instructions:
- Flash factory image from OEM WebUI:
openwrt-ath79-tiny-tplink_tl-wr740n-v5-squashfs-factory.bin
- Sysupgrade from ar71xx image:
openwrt-ath79-tiny-tplink_tl-wr740n-v5-squashfs-sysupgrade.bin
Signed-off-by: Jun Su <howard0su@gmail.com>
[commit title/message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Kevin Darbyshire-Bryant [Wed, 22 Jan 2020 22:03:56 +0000 (22:03 +0000)]
kernel: ifb: set default numifbs to 0
By default on module load, 2 ifb interfaces are created and typically
remain unused, cluttering 'ip link' outputs and generally confusing
things. sqm-scripts for example, creates its own ifb interface/s
instead of using these 2 defaults ifbs.
Tell the ifb module to not create any default ifbs on load via the
numifbs parameter.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Yufei Miao [Wed, 11 Mar 2020 05:38:53 +0000 (13:38 +0800)]
tools/cmake: Update to 3.16.5
Update cmake to 3.16.5
Signed-off-by: Yufei Miao <myf@myf.cloud>
Daniel Golle [Thu, 12 Mar 2020 19:53:36 +0000 (20:53 +0100)]
procd: actually wire-up netns support
When support for network namespaces was added to procd, adding the
corresponding jail flag in procd.sh was ommitted. Add it now.
Fixes: 97a03a4760 ("procd: update to latest git HEAD")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
David Bauer [Thu, 12 Mar 2020 13:08:30 +0000 (14:08 +0100)]
ath79: add back NAND symbols to NAND target
The NAND config symbols were removed unintentionally while adding
support for Linux 5.4.
Add the respective symbols for v4.19 as well as v5.4.
Signed-off-by: David Bauer <mail@david-bauer.net>
Tim Harvey [Wed, 11 Mar 2020 15:02:58 +0000 (08:02 -0700)]
imx6: add support for GW5907/GW5910/GW5912/GW5913
This patch adds support for GW5907/GW5910/GW5912/GW5913 IMX6 based boards
from the Gateworks Ventana Family[A]:
- backport upstream dt patches from 5.6 to 4.19 and 5.4
- add dtb's to ventana images
- add board-name and network config
A. https://www.gateworks.com/products/imx6-single-board-computer-gateworks-ventana-family
Flashing instructions for Ventana boards:
Using pre-flashed bootloader:
- Use appropriate ubi image depending on board NAND to flash via bootloader:
openwrt-imx6-ventana-squashfs-nand.ubi - 2KiB page size
openwrt-imx6-ventana-large-squashfs-nand.ubi - 4KiB page size
http://trac.gateworks.com/wiki/linux/ubi
Using Gateworks JTAG dongle:
- Use Gateworks mkimage_jtag script to create a JTAG image comprised of
pre-built bootloader and ubi image:
http://trac.gateworks.com/wiki/jtag_instructions
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Tue, 10 Mar 2020 15:03:20 +0000 (08:03 -0700)]
imx6: remove unnecessary wildcard from board name matching
The wildcard used in the network config matching is not necessary
given the board names returned by imx6_board_detect() in lib/imx6.sh.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tomasz Maciej Nowak [Tue, 25 Feb 2020 19:07:41 +0000 (20:07 +0100)]
layerscape: sysupgrade: require metadata
Require the image metadata check so no invalid image could be fed to
sysupgrade without force option.
Cc: Mathew McBride <matt@traverse.com.au>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tomasz Maciej Nowak [Tue, 25 Feb 2020 19:07:40 +0000 (20:07 +0100)]
layerscape: ls10121frdm: add sysupgrade
Instead of dangerous rewriting full chip with firmware.bin image to
update OpenWrt, add sysupgrade image. This image will be used to update
kernel and rootfs, leaving bootloader intact and making recovery
possible, without resorting to external hardware tools.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tomasz Maciej Nowak [Tue, 25 Feb 2020 19:07:39 +0000 (20:07 +0100)]
layerscape: ls1012afrdm: introduce dynamic partitioning
Combine fixed sizes of "kernel" and "rootfs" partitions into one
partition managed by OpenWrt splitter, it will allow better management
of chip capacity and less maintenance burden when compiled kernel image
will outgrow allocated size for kernel partition. This also changes kernel
image format, since splitter only manages kernel and rootfs partitions,
the dtb needs to be updated with the kernel, so for convenience, kernel is
packed to FIT image.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tomasz Maciej Nowak [Tue, 25 Feb 2020 19:07:38 +0000 (20:07 +0100)]
layerscape: ls1012afrdm: convert image to squashfs
This commit replaces UBIFS root partition with squashfs+overlay. It's
preparation for introducing dynamic partitioning.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tomasz Maciej Nowak [Tue, 25 Feb 2020 19:07:37 +0000 (20:07 +0100)]
layerscape: ls1012afrdm: add uncompressed initramfs
Uncompressing of initramfs image fails on board with U-Boot from "QorIQ
SDK (FSL Reference Distro) 2.0".
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tomasz Maciej Nowak [Tue, 25 Feb 2020 19:07:36 +0000 (20:07 +0100)]
layerscape: resurrect support for FRDM-LS1012A
Re-add support for NXP FRDM-LS1012A, which mimics the flash layout of the
rest boards supported by LSDK.
0x000000000000-0x000000100000 : "bl2"
0x000000100000-0x000000500000 : "fip"
0x000000500000-0x000000600000 : "u-boot-env"
0x000000600000-0x000000a00000 : "reserved-1"
0x000000a00000-0x000000d00000 : "pfe"
0x000000d00000-0x000000f00000 : "reserved-2"
0x000000f00000-0x000001000000 : "dtb"
0x000001000000-0x000002000000 : "kernel"
0x000002000000-0x000004000000 : "ubifs"
Specification
SoC: LS1012A single core 800MHz
RAM: 512 MB DDR3
Flash: 64 MB QSPI NOR
Ethernet: 2x 10/100/1000 Mbps
Connectors: µUSB 3.0 OTG
µUSB 2.0 (debugging & power input)
2x 3.5mm jack for microphone & headphone (SGTL5000)
Arduino Shield expansion with I2C, SPI, UART, and GPIO
JTAG
LEDS: 3x (non-configurable)
Buttons: 1x (reset, non-configurable)
Be advised that erasing or writing 64MB flash takes some time to finish.
Do not reset the board until all operations end with success, otherwise
You'll need external tools to re-program the flash chip.
Installation
Follow the QSPI programing procedure for LS1012AFRWY board in
target/linux/layerscape/README, point 3.3.
Don't forget about updating U-Boot environment with MAC addresses of
ethernet interfaces, variable 'ethaddr' for eth0 and 'eth1addr' for eth1.
As the LSDK images do not support sysupgrade, nor do changes in this
commit, it's planed in upcoming submissions.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tim Harvey [Mon, 9 Mar 2020 23:30:24 +0000 (16:30 -0700)]
kernel: 5.4: add unconfigured symbols
This patch adds a few symbols that I found that
need disabling in order to not break the build of octeontx
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Robert Marko [Tue, 10 Mar 2020 17:20:01 +0000 (18:20 +0100)]
generic: 5.4: Add 4B_OPCODES flag to w25q256
This patch backports the upstream patch that adds the 4B_OPCODES flag to w25q256 under 5.4 kernel.
This is needed for ipq40xx and ramips.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Robert Marko [Tue, 10 Mar 2020 17:17:02 +0000 (18:17 +0100)]
generic: 4.19: Add 4B_OPCODES flag to w25q256
This patch backports the upstream patch that adds the 4B_OPCODES flag to w25q256 under 4.19 kernel.
This is needed for ipq40xx and ramips.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Daniel Golle [Thu, 12 Mar 2020 09:25:21 +0000 (10:25 +0100)]
oxnas: switch to kernel 5.4 and remove kernel 4.14
Run-tested 5.4 on Shuttle KD20 for some days now, everything seems
fine so far. Let's have snapshot builds based on 5.4.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hauke Mehrtens [Sat, 29 Feb 2020 15:31:26 +0000 (16:31 +0100)]
x86: Remove kernel 4.14 support
This target was switched to kernel 4.19 more than 6 months ago in commit
f342ffd300da ("treewide: kernel: bump some targets to 4.19") and now
with kernel 5.4 support being added it gets harder to support kernel
4.14 in addition to kernel 4.19 and 5.4.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 29 Feb 2020 15:52:57 +0000 (16:52 +0100)]
tegra: Remove kernel 4.14 support
This target was switched to kernel 4.19 more than 6 months ago in commit
f342ffd300da ("treewide: kernel: bump some targets to 4.19") and now
with kernel 5.4 support being added it gets harder to support kernel
4.14 in addition to kernel 4.19 and 5.4.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 29 Feb 2020 15:38:58 +0000 (16:38 +0100)]
sunxi: Remove kernel 4.14 support
This target was switched to kernel 4.19 more than 6 months ago in commit
f342ffd300da ("treewide: kernel: bump some targets to 4.19") and now
with kernel 5.4 support being added it gets harder to support kernel
4.14 in addition to kernel 4.19 and 5.4.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 29 Feb 2020 15:52:36 +0000 (16:52 +0100)]
octeon: Remove kernel 4.14 support
This target was switched to kernel 4.19 more than 6 months ago in commit
f342ffd300da ("treewide: kernel: bump some targets to 4.19") and now
with kernel 5.4 support being added it gets harder to support kernel
4.14 in addition to kernel 4.19 and 5.4.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 29 Feb 2020 15:52:03 +0000 (16:52 +0100)]
mvebu: Remove kernel 4.14 support
This target was switched to kernel 4.19 more than 6 months ago in commit
f342ffd300da ("treewide: kernel: bump some targets to 4.19") and now
with kernel 5.4 support being added it gets harder to support kernel
4.14 in addition to kernel 4.19 and 5.4.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 29 Feb 2020 15:50:56 +0000 (16:50 +0100)]
mpc85xx: Remove kernel 4.14 support
This target was switched to kernel 4.19 more than 6 months ago in commit
f342ffd300da ("treewide: kernel: bump some targets to 4.19") and now
with kernel 5.4 support being added it gets harder to support kernel
4.14 in addition to kernel 4.19 and 5.4.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 29 Feb 2020 15:50:26 +0000 (16:50 +0100)]
malta: Remove kernel 4.14 support
This target was switched to kernel 4.19 more than 6 months ago in commit
f342ffd300da ("treewide: kernel: bump some targets to 4.19") and now
with kernel 5.4 support being added it gets harder to support kernel
4.14 in addition to kernel 4.19 and 5.4.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Yousong Zhou <yszhou4tech@gmail.com>
Hauke Mehrtens [Sat, 29 Feb 2020 15:36:21 +0000 (16:36 +0100)]
ipq40xx: Remove kernel 4.14 support
This target was switched to kernel 4.19 more than 6 months ago in commit
f342ffd300da ("treewide: kernel: bump some targets to 4.19") and now
with kernel 5.4 support being added it gets harder to support kernel
4.14 in addition to kernel 4.19 and 5.4.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 29 Feb 2020 15:49:58 +0000 (16:49 +0100)]
imx6: Remove kernel 4.14 support
This target was switched to kernel 4.19 more than 6 months ago in commit
f342ffd300da ("treewide: kernel: bump some targets to 4.19") and now
with kernel 5.4 support being added it gets harder to support kernel
4.14 in addition to kernel 4.19 and 5.4.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 29 Feb 2020 15:49:09 +0000 (16:49 +0100)]
gemini: Remove kernel 4.14 support
This target was switched to kernel 4.19 more than 6 months ago in commit
f342ffd300da ("treewide: kernel: bump some targets to 4.19") and now
with kernel 5.4 support being added it gets harder to support kernel
4.14 in addition to kernel 4.19 and 5.4.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 29 Feb 2020 15:34:31 +0000 (16:34 +0100)]
ath79: Remove kernel 4.14 support
This target was switched to kernel 4.19 more than 6 months ago in commit
f342ffd300da ("treewide: kernel: bump some targets to 4.19") and now
with kernel 5.4 support being added it gets harder to support kernel
4.14 in addition to kernel 4.19 and 5.4.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 29 Feb 2020 15:48:33 +0000 (16:48 +0100)]
armvirt: Remove kernel 4.14 support
This target was switched to kernel 4.19 more than 6 months ago in commit
f342ffd300da ("treewide: kernel: bump some targets to 4.19") and now
with kernel 5.4 support being added it gets harder to support kernel
4.14 in addition to kernel 4.19 and 5.4.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Yousong Zhou <yszhou4tech@gmail.com>
Sungbo Eo [Thu, 5 Mar 2020 13:57:29 +0000 (22:57 +0900)]
kernel: make kmod-ata-core selected by dependent modules
Currently kmod-ata-* will not get into images unless kmod-ata-core is added to
DEVICE_PACKAGES as well. By changing the dependencies from "depends on" to
"select", we do not have the issue anymore.
Furthermore, we can remove most occurrences of the package from DEVICE_PACKAGES
and similar variables, as it is now pulled by dependent modules such as:
- kmod-ata-ahci
- kmod-ata-ahci-mtk
- kmod-ata-sunxi
While at it, use AddDepends/ata for kmod-ata-pdc202xx-old.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Sungbo Eo [Tue, 10 Mar 2020 04:43:18 +0000 (13:43 +0900)]
ipq806x: replace ${} with $()
${} and $() are exactly the same. Follow the convention of using $().
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Sungbo Eo [Tue, 10 Mar 2020 04:42:57 +0000 (13:42 +0900)]
ipq40xx: replace ${} with $()
${} and $() are exactly the same. Follow the convention of using $().
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Sungbo Eo [Wed, 11 Mar 2020 01:35:48 +0000 (10:35 +0900)]
sunxi: remove SUNXI_UBOOT from DEVICE_VARS
All SUNXI_UBOOT usages were removed in
e018c4d7ab8b ("uboot-sunxi: clean up,
switch to u-boot.mk"). Now drop the variable completely.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Sungbo Eo [Mon, 9 Mar 2020 07:21:42 +0000 (16:21 +0900)]
oxnas: clean up DEVICE_VARS
DTS variable is not used in any device. Just drop it.
UBIFS_OPTS is not device-dependent here. Remove it from DEVICE_VARS.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Sungbo Eo [Mon, 9 Mar 2020 12:14:06 +0000 (21:14 +0900)]
build: image: move IMAGE_SIZE to image.mk
IMAGE_SIZE is widely used in many targets. Declare it in the default template to
clean up redundant code. This also prevents deriving IMAGE_SIZE unintentionally
from the previously defined device.
While at it, remove duplicate KERNEL_SIZE declaration.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Adrian Schmutzler [Wed, 11 Mar 2020 15:05:40 +0000 (16:05 +0100)]
ar71xx: fix port order on TP-Link Archer C60 v1/v2
The labels on the LAN ports of the TP-Link Archer C60 v1/v2 are
actually inverted compared to the ports of the internal switch.
Add this information to 02_network.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Wed, 11 Mar 2020 15:00:56 +0000 (16:00 +0100)]
ath79: fix port order on TP-Link Archer C60 v1/v2
The labels on the LAN ports of the TP-Link Archer C60 v1/v2 are
actually inverted compared to the ports of the internal switch.
Add this information to 02_network.
This is the same for to-be-supported v3 of this device.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Wed, 11 Mar 2020 14:52:41 +0000 (15:52 +0100)]
ar71xx: remove wrong MAC address adjustment for Archer C60 v2
The adjustment of the MAC address for Archer C60 v2 in 10_fix_wifi_mac
is broken since a "mac" partition is not set up for this device on
ar71xx. Instead, the MAC address is already patched correctly in
11-ath10k-caldata.
Remove the useless adjustment.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Wed, 11 Mar 2020 14:46:00 +0000 (15:46 +0100)]
ar71xx: fix swapped LAN/WAN MAC address for Archer C60 v1/v2
The MAC addresses for lan/wan are swapped compared to the vendor
firmware. This adjusts to vendor configuration, which is:
lan *:7b label
wan *:7c label+1
2.4g *:7b label
5g *:7a label-1
Only one address is stored in <&mac 0x8>, corresponding to the label.
This has been checked on revisions v1, v2 and v3.
Since ar71xx calculates the ath10k MAC address based on the ethernet
addresses, the number there is adjusted, too.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Wed, 11 Mar 2020 14:37:34 +0000 (15:37 +0100)]
ath79: fix swapped LAN/WAN MAC address for Archer C60 v1/v2
The MAC addresses for lan/wan are swapped compared to the vendor
firmware. This adjusts to vendor configuration, which is:
lan *:7b label
wan *:7c label+1
2.4g *:7b label
5g *:7a label-1
Only one address is stored in <&mac 0x8>, corresponding to the label.
This has been checked on revisions v1, v2 and v3.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Felix Fietkau [Wed, 11 Mar 2020 12:33:23 +0000 (13:33 +0100)]
mt76: update to the latest version
a94e43f277e2 mt76: mt76x02: reset MCU timeout counter earlier in watchdog reset
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Petr Štetiar [Thu, 5 Mar 2020 11:46:21 +0000 (12:46 +0100)]
armvirt: fix missing watchdog core dependency for hwmon-sch5627
Fixes following error uncovered while building armvirt/64 on 5.4:
Package kmod-hwmon-sch5627 is missing dependencies for the following libraries:
watchdog.ko
That dependency was introduced in upstream via
2d8c7ff52c24
("hwmon/sch56xx: Depend on watchdog for watchdog core functions") in
v3.5.
The issue emerged in 5.4 because the kconfig symbol CONFIG_WATCHDOG_CORE
is now a tristate value. Previously it was a bool.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Catrinel Catrinescu [Wed, 11 Mar 2020 09:10:00 +0000 (10:10 +0100)]
ar71xx/ath79: ew-dorin, fix the trigger level for WPS button
Because the WPS button had the wrong trigger level,
the failsafe mode was triggered quite often,
after this commit:
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=
27f3f493de
Signed-off-by: Catrinel Catrinescu <cc@80211.de>
Rafał Miłecki [Wed, 11 Mar 2020 07:39:29 +0000 (08:39 +0100)]
kernel: backport out-of-memory fix for non-Ethernet devices
Doing up & down on non-Ethernet devices (e.g. monitor mode interface)
was consuming memory.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Hans Dedecker [Tue, 10 Mar 2020 21:08:36 +0000 (22:08 +0100)]
curl: bump to 7.69.0
For changes in 7.69.0; see https://curl.haxx.se/changes.html#7_69_0
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
David Bauer [Sun, 8 Mar 2020 20:39:19 +0000 (21:39 +0100)]
ramips: add support for Ubiquiti UniFi nanoHD
Hardware
--------
SoC: MediaTek MT7621AT
WiFi: MediaTek MT7603 bgn 2T2R
MediaTek MT7615 ac 4T4R
Flash: 32M SPI (Macronix MX25L25635F)
RAM: 128M DDR3 (Winbond W631GG6KB)
LED: Dome (Blue / White)
BTN: Reset
Installation
------------
These instructions were written for firmware version v3.9.27.
Downgrade if necessary.
1. Copy the OpenWrt sysupgrade image to the devices /tmp folder
via scp. On factory defaults, user and password is "ubnt" at
192.168.1.20/24.
2. Write the bootselect flag. Otherwise, the device might boot from the
wrong partition. Verify the mtd partition used in the command below
is the one labled "bs" in /proc/mtd (as this might change in the
future).
> dd if=/dev/zero bs=1 count=1 of=/dev/mtd4
3. Write the OpenWrt sysupgrade to the mtd partitions labled
"kernel0" and "kernel1".
> dd if=/tmp/openwrt-sysupgrade.bin of=/dev/mtdblock6
> dd if=/tmp/openwrt-sysupgrade.bin of=/dev/mtdblock7
4. Reboot or powercycle the device.
Signed-off-by: David Bauer <mail@david-bauer.net>
Kevin Darbyshire-Bryant [Tue, 10 Mar 2020 15:13:40 +0000 (15:13 +0000)]
build: clean menuconfig utility as part of dirclean
When sharing a common build directory between different build platforms
eg. macos v docker based linux v virtual machine, a 'make dirclean'
isn't quite enough to clean all the platform related binaries. The
'conf' and 'mconf' aka 'make menuconfig/defconfig & friends' utilities
remain.
Clean those as part of 'dirclean' so they get rebuilt for the current
platform on the next 'make'
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Rafał Miłecki [Tue, 10 Mar 2020 14:46:49 +0000 (15:46 +0100)]
bcm47xx: add support for kernel 5.4
Ethernet, switch, LEDs, buttons, USB, sysupgrade & LuCI were
successfully tested on BCM4706.
WARNING: Hack for BCM4710 adding BCM4710_PROTECTED_FILL_TLB() to the
local_r4k_flush_cache_sigtramp() could not be ported. That function has
been dropped in:
commit
adcc81f148d7 ("MIPS: math-emu: Write-protect delay slot emulation pages")
commit
3315b6b336c8 ("MIPS: Delete unused flush_cache_sigtramp()")
it's unsure if that chipset will still work reliably.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Tue, 10 Mar 2020 12:26:57 +0000 (13:26 +0100)]
bcm47xx: switch to kernel 4.19
Ethernet, switch, LEDs, buttons, USB, sysupgrade & LuCI were
successfully tested on BCM4706.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Kevin Darbyshire-Bryant [Mon, 9 Mar 2020 11:36:12 +0000 (11:36 +0000)]
dnsmasq: bump to v2.81rc3
Bump to latest release candidate and drop 2 local patches that have been
upstreamed.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Leon M. George [Thu, 7 Nov 2019 12:24:40 +0000 (13:24 +0100)]
ipq40xx: add cpximg to flash Compex WPJ428 via bootloader
Generate a cpximg that is compatible with the cpximg loader in Compex' u-boot.
The cpximg loader can be started either by holding the reset button during power
up or by entering the u-boot prompt and entering 'cpximg'.
Once it's running, a TFTP-server under 192.168.1.1 will accept an image
appropriate for the board revision that is etched on the board (e.g. 6A04).
The image can be pushed using tftp:
tftp -v -m binary 192.168.1.1 -c put openwrt-ipq40xx-generic-compex_wpj428-squashfs-cpximg-6a04.bin
cpximg files can also be used with the sysupgrade utility in stock images.
(add SSH key in luci for root access)
In mkmylofw_32m, the calculation of the "partition size" has been preferred
to just padding the partition as this will result in less block transfers
during flashing (while the additional complexity is bearable).
Signed-off-by: Leon M. George <leon@georgemail.eu>
Co-developed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Yousong Zhou [Tue, 10 Mar 2020 08:02:46 +0000 (16:02 +0800)]
armvirt: switch to kernel 5.4
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Yousong Zhou [Tue, 10 Mar 2020 08:03:30 +0000 (16:03 +0800)]
armvirt: 5.4: kconfig sync
"make kernel_menuconfig CONFIG_TARGET=subtarget_platform" first, then
move common ones to platform level config
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Yousong Zhou [Tue, 10 Mar 2020 07:19:48 +0000 (15:19 +0800)]
armvirt: add config-5.4
Copied from config-4.19
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Yousong Zhou [Tue, 10 Mar 2020 06:42:01 +0000 (14:42 +0800)]
kernel: 5.4: remove some dup config options already set in generic
This furthers
860652f4b9da ("kernel: 5.4: move some kconfig options to
generic")
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Yousong Zhou [Wed, 4 Mar 2020 07:43:30 +0000 (15:43 +0800)]
malta: switch to kernel 5.4 by default
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Petr Štetiar [Thu, 5 Mar 2020 11:46:21 +0000 (12:46 +0100)]
malta: fix missing watchdog core dependency for hwmon-sch5627
Fixes following error uncovered while building malta/be on 5.4:
Package kmod-hwmon-sch5627 is missing dependencies for the following libraries:
watchdog.ko
That dependency was introduced in upstream via
2d8c7ff52c24
("hwmon/sch56xx: Depend on watchdog for watchdog core functions") in
v3.5.
The issue emerged in 5.4 because the kconfig symbol CONFIG_WATCHDOG_CORE
is now a tristate value. Previously it was a bool
Cc: Yousong Zhou <yszhou4tech@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
(drop the config-4.19 change. reword about the cause)
Yousong Zhou [Wed, 4 Mar 2020 04:30:46 +0000 (12:30 +0800)]
malta: update kernel config-5.4
With malta/be selected
make kernel_menuconfig CONFIG_TARGET=subtarget_platform
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Yousong Zhou [Mon, 2 Mar 2020 04:23:09 +0000 (12:23 +0800)]
malta: add kernel 5.4 config
Copied from config-4.19
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Yousong Zhou [Tue, 3 Mar 2020 15:28:18 +0000 (23:28 +0800)]
kernel: 5.4: move some kconfig options to generic
CONFIG_64BIT_TIME=y
CONFIG_KASAN_STACK=1
CONFIG_UBSAN_ALIGNMENT=y
CONFIG_UNIX_SCM=y
CONFIG_DMA_DECLARE_COHERENT=y
CONFIG_OF_RESERVED_MEM=y
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Christoph Krapp [Mon, 2 Mar 2020 21:24:19 +0000 (22:24 +0100)]
ramips: add support for TP-Link RE210 v1
Hardware
--------
SoC: MediaTek MT7620A
RAM: 64MB
FLASH: 8MB SPI
WLAN: 2G: MediaTek MT7620A
5G: MediaTek MT7610EN
ETH: 1x 10/100/1000M (Atheros AR8035)
LED: RSSI (orange/green)
WiFi 2G (green)
WiFi 5G (green)
Power (green)
System (red / green)
BTN: Power
Reset
LED
WPS
Serial
------
P1 - Tx
P2 - Rx
P3 - GND
P4 - VCC
Pin 4 is the one closest to the LAN port.
MAC overview
------------
WAN *:4c uboot 0x1fc00
2.4 *:4c uboot 0x1fc00
5 *:4e uboot 0x1fc00 +2
Installation
------------
Web interface:
It is possible to upgrade to OpenWrt via the web interface. However, the
OEM firmware upgrade file is required and a tool to fix the MD5 sum of
the header. This procedure overwrites U-Boot and there is not failsafe /
recovery mode present! To prepare an image, you need to take the header
and U-Boot (i.e. 0x200 + 0x20000 bytes) from an OEM firmware file and
attach the factory image to it. Then fix the header MD5Sum1.
Serial/TFTP:
You can use initramfs for booting via RAM or flash the image directly.
Additional Notes:
If the web interface upgrade fails, you have to open your device and
attach serial console. Since the web upgrade overwrites the boot loader,
you might also brick your device.
In order to flash back to stock, the first header and U-Boot needs to be
stripped from the original firmware.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[change rssi LED labels]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Koen Vandeputte [Mon, 9 Mar 2020 11:39:35 +0000 (12:39 +0100)]
kernel: bump 5.4 to 5.4.24
Refreshed all patches.
Compile-tested on: imx6
Runtime-tested on: imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Mon, 9 Mar 2020 11:22:15 +0000 (12:22 +0100)]
kernel: bump 4.19 to 4.19.108
Refreshed all patches.
Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
projects / openwrt / staging / dangole.git / log