wlcore: move wl12xx_platform_data up and make it truly optional

The platform data is used not only by wlcore-based drivers, but also
by wl1251.  Move it up in the directory hierarchy to reflect this.

Additionally, make it truly optional.  At the moment, disabling
platform data while wl1251_sdio or wlcore_sdio are enabled doesn't
work, but it will be necessary when device tree support is
implemented.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>

wlcore: use PLATFORM_DEVID_AUTO for plat dev creation to avoid conflicts

The platform devices can be created by both wlcore_sdio and
wlcore_spi.  Theoretically, if both are connected to the same board,
there will be a conflict.

Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: use wl12xx_platform_data pointer from wlcore_pdev_data

Just a small cleanup to use the pointer provided by wlcore_pdev_data
instead of using a separate pointer then copying.

Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: remove if_ops from platform_data

We can't pass pointers from the platform data to the modules, because
with DT it cannot be done.  Those pointers are not set by the board
files anyway.  It's the bus modules that set them, so they can be
safely removed from the platform data without changing any board
files.

Create a new structure that the bus modules pass to wlcore.  This
structure contains the if_ops pointers and a pointer to the actual
platform data.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>

wlcore: remove unused set_power method

There is no platform-specific set_power method anymore.  Power setting
is done in the bus modules (wlcore_sdio and wlcore_spi).

Signed-off-by: Luciano Coelho <coelho@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>

wlcore: use single-role version when verifying the PLT firmware

The PLT firmware used by wl12xx for calibration always has the same
version number as the single-role firmware.

Currntly the driver rejects the PLT firmware since anything that is
not single-role uses the multi-role version.  Fix this by using the
single-role version for everything except multi-role.

Signed-off-by: Luciano Coelho <coelho@ti.com>

rtlwifi: rtl8723ae: Fix W=1 compile warnings

Whe this driver is built with "make W=1", the following warnings are output:

drivers/net/wireless/rtlwifi/rtl8723ae/fw.c:515:5: warning: variable ‘own’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8723ae/hal_btc.c:1436:5: warning: variable ‘bt_retry_cnt’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8723ae/hw.c:706:6: warning: variable ‘reg_ratr’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8723ae/hw.c:2033:41: warning: variable ‘cur_rfstate’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8723ae/phy.c:620:23: warning: variable ‘radiob_arraylen’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8723ae/phy.c:619:7: warning: variable ‘radiob_array_table’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8723ae/phy.c:617:7: warning: variable ‘rtstatus’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8723ae/phy.c:1534:6: warning: variable ‘bbvalue’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8723ae/phy.c:1716:6: warning: variable ‘reg_ecc’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8723ae/phy.c:1715:61: warning: variable ‘reg_ec4’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8723ae/phy.c:1715:34: warning: variable ‘reg_eac’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8723ae/trx.c:247:6: warning: variable ‘psaddr’ set but not used [-Wunused-but-set-variable]

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192de: Fix W=1 build warnings

when this driver is built with "make W=1", the following warning is printed:

drivers/net/wireless/rtlwifi/rtl8192de/dm.c:1058:5: warning: comparison is always false due to limited range of data type [-Wtype-limits]

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192cu: Fix W=1 build warning

When this driver is built with "make W=1", the following warning is output:

drivers/net/wireless/rtlwifi/rtl8192cu/sw.c:56:6: warning: variable ‘err’ set but not used [-Wunused-but-set-variable]

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192c: Fix W=1 warning

When this driver is built with "make W=1", the following warning occurs:

drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c:907:4: warning: comparison is always false due to limited range of data type [-Wtype-limits]

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Fix warnings in usb.c

Building this driver with "make W=1" results in the following 2 warnings:

drivers/net/wireless/rtlwifi/usb.c:829:21: warning: variable ‘urb_list’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/usb.c:828:23: warning: variable ‘skb_list’ set but not used [-Wunused-but-set-variable]

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Fix many compile warnings when using W=1

Many warnings like the following arise from a build with W=1 on the
make line:

warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]

Changing the overall debug level storage from unsigned to signed fixes these.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: rt2x00: rt2800pci add id

0x1814,0x359f is a RT3592 802.11a/b/g/n 2x2 WiFi Adapter
support added by 872834dfb38edc6f72cfc783a5ce78f2a9f36ec5

Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: users@rt2x00.serialmonkey.com
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: cc: fix (and rename) define of NAND flash type

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Remove unused variables in ath_mci_cleanup

Leaving the unused variables ath_mci_cleanup causes build warnings.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix sparse __CHECK_ENDIAN__ for spectral code

Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Only remove spectral scan relay file when it was created

The relay file depends on relayfs. Trying to close this file without having
ATH9K_DEBUGFS (and therefore RELAY) activated causes build failures.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Only add fix_rssi_inv_only when spectral code is used

The code is only used when ATH9K_DEBUGFS is activated and causes build warnings
when it is still compiled without user.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Only process fft samples when ATH9K_DEBUGFS is enabled

The code can only be used when ATH9k_DEBUGFS is enabled an not when ATH_DEBUG
is activated. Still enabling it would cause build failures.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Select RELAY for ATH9K_DEBUGFS

The spectral scan support activated through ATH9K_DEBUGFS depends on RELAY for
the kernel->userspace communication. Not activating RELAY causes build
failures.

The RELAY is added as select instead of depend to do it similar like
the only other user of RELAY: BLK_DEV_IO_TRACE

Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: remove max_tx_buf_size

max_tx_buf_size is not used any more after reconfiguration of
tx buffer size has been removed.

Also add missing curr_tx_buf_size update while dumping debug info
via debugfs.

Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: do not reconfigure tx buffer size in firmware while associating

It's observed that reconfiguration of tx buffer size before
association can cause data path failure in firmware after
associated. Although this is only found with PCIe cards, but
potentially it could happen with any other interfaces as well.

The tx buffer reconfiguration is not really useful in firmware.
Let's remove it for all interfaces.

Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: report A-MPDU status

The ath9k hardware reports whenever an frame was part
of an A-MPDU. MAC80211 already provides the necessary
API to pass this additional information along to
whomever needs it.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: rt2x00: rt2800usb add/identify ids

Devices were taken from Ralink Linux drivers:
- RT5370
0x043e, 0x7a32
0x043e, 0x7a42
0x0471, 0x2126
0x0471, 0x2180
0x0471, 0x2181
0x0471, 0x2182

Identify these ones:
0x04da, 0x23f6 in CONFIG_RT2800USB_RT53XX is a Panasonic device
0x07d1, 0x3c17 in RT2800USB_UNKNOWN is a RT3070
0x0586, 0x341a in RT2800USB_UNKNOWN is a RT3070

Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: users@rt2x00.serialmonkey.com
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: check for dma mapping errors

Handle pci_map_page() errors. This fixes "DMA-API: device driver failed
to check map error" warning.

Reported-by: Zdenek Kabelac <zkabelac@redhat.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: Xflash: reorder includes to make pr_fmt work

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl4965: report A-MPDU status

This patch is based on "iwlwifi: report A-MPDU status".
(12bf6f45d1703858)

Since the firmware will give us an A-MPDU bit and
only a single PHY information packet for all the
subframes in an A-MPDU, we can easily report the
minimal A-MPDU information for radiotap.

Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-upstream' of git://git./linux/kernel/git/bluetooth/bluetooth-next

Bluetooth: Refactor mgmt_pending_foreach

This patch does a trivial refactor in mgmt_pending_foreach function.
It replaces list_for_each_safe by list_for_each_entry_safe, simplifying
the function.

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Remove unneeded locking

This patch removes unneeded locking in hci_le_adv_report_evt. There
is no need to lock hdev before calling mgmt_device_found.

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Reduce critical section in sco_conn_ready

This patch reduces the critical section protected by sco_conn_lock in
sco_conn_ready function. The lock is acquired only when it is really
needed.

This patch fixes the following lockdep warning which is generated
when the host terminates a SCO connection.

Today, this warning is a false positive. There is no way those
two threads reported by lockdep are running at the same time since
hdev->workqueue (where rx_work is queued) is single-thread. However,
if somehow this behavior is changed in future, we will have a
potential deadlock.

======================================================
[ INFO: possible circular locking dependency detected ]
3.8.0-rc1+ #7 Not tainted
-------------------------------------------------------
kworker/u:1H/1018 is trying to acquire lock:
 (&(&conn->lock)->rlock){+.+...}, at: [<ffffffffa0033ba6>] sco_chan_del+0x66/0x190 [bluetooth]

but task is already holding lock:
 (slock-AF_BLUETOOTH-BTPROTO_SCO){+.+...}, at: [<ffffffffa0033d5a>] sco_conn_del+0x8a/0xe0 [bluetooth]

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #1 (slock-AF_BLUETOOTH-BTPROTO_SCO){+.+...}:
       [<ffffffff81083011>] lock_acquire+0xb1/0xe0
       [<ffffffff813efd01>] _raw_spin_lock+0x41/0x80
       [<ffffffffa003436e>] sco_connect_cfm+0xbe/0x350 [bluetooth]
       [<ffffffffa0015d6c>] hci_event_packet+0xd3c/0x29b0 [bluetooth]
       [<ffffffffa0004583>] hci_rx_work+0x133/0x870 [bluetooth]
       [<ffffffff8104d65f>] process_one_work+0x2bf/0x4f0
       [<ffffffff81050022>] worker_thread+0x2b2/0x3e0
       [<ffffffff81056021>] kthread+0xd1/0xe0
       [<ffffffff813f14bc>] ret_from_fork+0x7c/0xb0

-> #0 (&(&conn->lock)->rlock){+.+...}:
       [<ffffffff81082215>] __lock_acquire+0x1465/0x1c70
       [<ffffffff81083011>] lock_acquire+0xb1/0xe0
       [<ffffffff813efd01>] _raw_spin_lock+0x41/0x80
       [<ffffffffa0033ba6>] sco_chan_del+0x66/0x190 [bluetooth]
       [<ffffffffa0033d6d>] sco_conn_del+0x9d/0xe0 [bluetooth]
       [<ffffffffa0034653>] sco_disconn_cfm+0x53/0x60 [bluetooth]
       [<ffffffffa000fef3>] hci_disconn_complete_evt.isra.54+0x363/0x3c0 [bluetooth]
       [<ffffffffa00150f7>] hci_event_packet+0xc7/0x29b0 [bluetooth]
       [<ffffffffa0004583>] hci_rx_work+0x133/0x870 [bluetooth]
       [<ffffffff8104d65f>] process_one_work+0x2bf/0x4f0
       [<ffffffff81050022>] worker_thread+0x2b2/0x3e0
       [<ffffffff81056021>] kthread+0xd1/0xe0
       [<ffffffff813f14bc>] ret_from_fork+0x7c/0xb0

other info that might help us debug this:

 Possible unsafe locking scenario:

       CPU0                    CPU1
       ----                    ----
  lock(slock-AF_BLUETOOTH-BTPROTO_SCO);
                               lock(&(&conn->lock)->rlock);
                               lock(slock-AF_BLUETOOTH-BTPROTO_SCO);
  lock(&(&conn->lock)->rlock);

 *** DEADLOCK ***

4 locks held by kworker/u:1H/1018:
 #0:  (hdev->name#2){.+.+.+}, at: [<ffffffff8104d5f8>] process_one_work+0x258/0x4f0
 #1:  ((&hdev->rx_work)){+.+.+.}, at: [<ffffffff8104d5f8>] process_one_work+0x258/0x4f0
 #2:  (&hdev->lock){+.+.+.}, at: [<ffffffffa000fbe9>] hci_disconn_complete_evt.isra.54+0x59/0x3c0 [bluetooth]
 #3:  (slock-AF_BLUETOOTH-BTPROTO_SCO){+.+...}, at: [<ffffffffa0033d5a>] sco_conn_del+0x8a/0xe0 [bluetooth]

stack backtrace:
Pid: 1018, comm: kworker/u:1H Not tainted 3.8.0-rc1+ #7
Call Trace:
 [<ffffffff813e92f9>] print_circular_bug+0x1fb/0x20c
 [<ffffffff81082215>] __lock_acquire+0x1465/0x1c70
 [<ffffffff81083011>] lock_acquire+0xb1/0xe0
 [<ffffffffa0033ba6>] ? sco_chan_del+0x66/0x190 [bluetooth]
 [<ffffffff813efd01>] _raw_spin_lock+0x41/0x80
 [<ffffffffa0033ba6>] ? sco_chan_del+0x66/0x190 [bluetooth]
 [<ffffffffa0033ba6>] sco_chan_del+0x66/0x190 [bluetooth]
 [<ffffffffa0033d6d>] sco_conn_del+0x9d/0xe0 [bluetooth]
 [<ffffffffa0034653>] sco_disconn_cfm+0x53/0x60 [bluetooth]
 [<ffffffffa000fef3>] hci_disconn_complete_evt.isra.54+0x363/0x3c0 [bluetooth]
 [<ffffffffa000fbd0>] ? hci_disconn_complete_evt.isra.54+0x40/0x3c0 [bluetooth]
 [<ffffffffa00150f7>] hci_event_packet+0xc7/0x29b0 [bluetooth]
 [<ffffffff81202e90>] ? __dynamic_pr_debug+0x80/0x90
 [<ffffffff8133ff7d>] ? kfree_skb+0x2d/0x40
 [<ffffffffa0021644>] ? hci_send_to_monitor+0x1a4/0x1c0 [bluetooth]
 [<ffffffffa0004583>] hci_rx_work+0x133/0x870 [bluetooth]
 [<ffffffff8104d5f8>] ? process_one_work+0x258/0x4f0
 [<ffffffff8104d65f>] process_one_work+0x2bf/0x4f0
 [<ffffffff8104d5f8>] ? process_one_work+0x258/0x4f0
 [<ffffffff8104fdc1>] ? worker_thread+0x51/0x3e0
 [<ffffffffa0004450>] ? hci_tx_work+0x800/0x800 [bluetooth]
 [<ffffffff81050022>] worker_thread+0x2b2/0x3e0
 [<ffffffff8104fd70>] ? busy_worker_rebind_fn+0x100/0x100
 [<ffffffff81056021>] kthread+0xd1/0xe0
 [<ffffffff81055f50>] ? flush_kthread_worker+0xc0/0xc0
 [<ffffffff813f14bc>] ret_from_fork+0x7c/0xb0
 [<ffffffff81055f50>] ? flush_kthread_worker+0xc0/0xc0

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Increment Management interface revision

This patch increments the management interface revision due to the
various fixes, improvements and other changes that have gone in lately.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Fix link security setting when powering on

If a controller is powered on while the HCI_AUTO_OFF flag is set the
link security setting (HCI_LINK_SECURITY) might not be in sync with the
actual state of the controller (HCI_AUTH). This patch fixes the issue by
checking for inequality between the intended and actual settings and
sends a HCI_Write_Auth_Enable command if necessary.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Add support for 128-bit UUIDs in EIR data

This patch adds the necessary code for encoding a list of 128-bit UUIDs
into the EIR data.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Add support for 32-bit UUIDs in EIR data

This patch adds the necessary code for inserting a list of 32-bit UUIDs
into the EIR data.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Refactor UUID-16 list generation into its own function

We will need to create three separate UUID lists in the EIR data (for
16, 32 and 128 bit UUIDs) so the code is easier to follow if each list
is generated in their own function.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Remove useless eir_len variable from EIR creation

The amount of data encoded so far in the create_eir() function can be
calculated simply through the difference between the data and ptr
pointer variables. The eir_len variable then becomes essentially
useless.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Simplify UUID16 list generation for EIR

There's no need to use two separate loops to generate a UUID list for
the EIR data. This patch merges the two loops previously used for the
16-bit UUID list generation into a single loop, thus simplifying the
code a great deal.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Simplify UUID removal code

The UUID removal code can be simplified by using
list_for_each_entry_safe instead of list_for_each_safe.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Keep track of UUID type upon addition

The primary purpose of the UUIDs is to enable generation of EIR and AD
data. In these data formats the UUIDs are split into separate fields
based on whether they're 16, 32 or 128 bit UUIDs. To make the generation
of these data fields simpler this patch adds a type member to the
bt_uuid struct and assigns a value to it as soon as the UUID is added to
the kernel. This way the type doesn't need to be calculated each time
the UUID list is later iterated.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Simplify UUIDs clearing code

The code for clearing the UUIDs list can be simplified by using
list_for_each_entry_safe instead of list_for_each_safe.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Store UUIDs in the same order that they were added

We should be encoding UUIDs to the EIR data in the same order that they
were added to the kernel, i.e. each UUID should be added to the end of
the UUIDs list. This patch fixes the issue by using list_add_tail
instead of list_add for storing the UUIDs.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

iwlwifi: move register access lock into transport

Move the reg_lock that protects HW register access
into the transport implementation. Locking is no
longer exposed, but handled internally in grab and
release NIC access. This simplifies the users.

Signed-off-by: Lilach Edelstein <lilach.edelstein@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: add iwl_set_bits_mask to transport API

Express iwl_set_bit() and iwl_clear_bit() through iwl_set_bits_mask()
and add the latter to the transport's API in order to allow different
implementation for different transport types in the future.

Signed-off-by: Lilach Edelstein <lilach.edelstein@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: lower BT coex aggregation message severity

As the rate scaling algorithm will attempt to enable
aggregation over and over again, the message will
flood the log if there is, for example, Bluetooth
streaming music. Make it a debug messages instead of
printing it all the time.

Reported-by: Jan-Michael Brummer <jan.brummer@tabos.org>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: add the MVM driver

Newer firmware revisions have a completely new
firmware API. This is the new driver for this
new API.

I've listed the people who directly contributed
code, but many others from various teams have
contributed in other ways.

Cc: Alexander Bondar <alexander.bondar@intel.com>
Cc: Amit Beka <amit.beka@intel.com>
Cc: Amnon Paz <amnonx.paz@intel.com>
Cc: Assaf Krauss <assaf.krauss@intel.com>
Cc: David Spinadel <david.spinadel@intel.com>
Cc: Dor Shaish <dor.shaish@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Eytan Lifshitz <eytan.lifshitz@intel.com>
Cc: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: add NVM and PHY DB code for new MVM driver

The new MVM (multi-virtual MAC) firmware driver
requires NVM (non-volatile memory) parsing code
and some PHY information database code. Add this
separately.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: fix calibration parser

The firmware TLV for calibration data isn't
really a u64, but two u32 values. Define a
struct for that and change the parser.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: clean up CMD_MODE enum

Just format the enum better.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwlwifi: add 7000 series device configuration

Add configuration and detection code for the new
7000 series, with 7260 and 3160 devices.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Merge remote-tracking branch 'wireless-next/master' into iwlwifi-next

wil6210: fix wil_vring_init_tx status

In case vring setup with the firmware failed,
success status was returned. fix it.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: Never delete Rx chain with firmware

Firmware crash on attempt to delete Rx chain.
Driver part of Rx chain removed only in preparation for the target reset;
as reset is the only flow that removes Rx chain in the firmware.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: checkpatch warnings

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: fix checkpatch CamelCase warnings

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: Reorder reset preparation sequence

Disable interrupts first to prevent spurious WMI events arrival

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: Separate common code for mbox regs caching to function

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: Fix "don't scan after connect" logic

When connect times out, scan was not re-enabled.

Strictly say, it is firmware issue - it should issue "disconnect"
event but it does not. Compensate in the driver.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: Call skb_orphan() right before Rx indication

Other parts of Rx path (BACK logic) will need to access associated data

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: Fix: Tx stall

Due to multi-tx-queue design, wil_start_xmit() used to be executed
concurrently for different queues. Then, these transmits delivered
to the same queue, creating race.

As result, Tx descriptor may be skipped, causing stall in hardware.

Convert to single Tx queue fixes it.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: Count Tx statistics on Tx completion

This allows to account for Tx errors

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: Refactor rx init/fini

Move WMI related operations to wmi.c as helper functions

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: remove raw wil_dbg() calls

Introduce debug category "MISC", convert all raw wil_dbg() to this category.
This improves dynamic debug manageability

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: rearrange IRQ debug printing

Make printings from IRQ appears in dmesg in chronological order

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: Detect FW error

In the firmware, added is ability to report internal errors using IRQ.

Catch this IRQ and notify user space via netlink

User space get notified like (udevadm monitor --kernel --property):

KERNEL[12660.320520] change   /devices/pci0000:00/0000:00:1c.1/0000:02:00.0/0000:03:01.0/0000:05:00.0/net/wlan12 (net)
ACTION=change
DEVPATH=/devices/pci0000:00/0000:00:1c.1/0000:02:00.0/0000:03:01.0/0000:05:00.0/net/wlan12
DEVTYPE=wlan
EVENT=FW_ERROR
IFINDEX=6
INTERFACE=wlan12
SEQNUM=2489
SOURCE=wil6210
SUBSYSTEM=net

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: avoid out of bounds access in mwifiex_get_common_rates.

Check that the array indexes are in-bounds before accessing the rate2 and tmp
arrays.

Found with the following semantic patch:

<smpl>
@@
identifier t;
identifier idx;
expression E;
statement S;
@@
* for (... ; <+... t[idx] ...+> && idx < E ; ...)
S
</smpl>

Signed-off-by: Cyril Roelandt <tipecaml@gmail.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Eliminate two empty routines

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

net: iwlegacy: remove unused variable

Fix:

drivers/net/wireless/iwlegacy/4965.c: In function ‘il4965_post_associate’:
drivers/net/wireless/iwlegacy/4965.c:1751:25: warning: variable ‘conf’ set but
not used [-Wunused-but-set-variable]

seen when building allmodconfig on x86_64 with W=1 by removing the unused
variable.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: fix antenna bitmask

This patch is based on "iwlwifi: fix antenna bitmask".
(362b0563b28506d53)

Like the new iwlagn devices, the old 4965N device only
supports a maximum of three antennas. Hence only three
bits are used, the fourth bit is likely the A-MPDU
indicator.

Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: add gpio_to_irq

The old bcm47xx gpio code had support for gpio_to_irq, but the new
code did not provide this function, but returned -ENXIO all the time.
This patch adds the missing function.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ssb: add gpio_to_irq

The old bcm47xx gpio code had support for gpio_to_irq, but the new
code did not provide this function, but returned -ENXIO all the time.
This patch adds the missing function.

arch/mips/bcm47xx/wgt634u.c calls gpio_to_irq() and got the correct irq
number with the old gpio handling code. With this patch the code in
wgt634u.c should work again. I do not have a wgt634u to test this.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: do not overwrite error code from lower layer driver

Instead of converting it to a bogus error code -1, we should
return the original error code from lower layer driver. This
error code will be printed so it may give user some clues on
what has happened.

Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: don't return zero on failure paths in mwifiex_pcie_init()

If pci_iomap() fails in mwifiex_pcie_init(), it breaks off initialization,
deallocates all resources, but returns zero.
The patch adds -EIO as return value in this case.

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtl8723ae: Fix misspellings sucess->success

Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: Do not call STA specific cmds not supported by the AP fw

While using STA mode in the AP firmware, avoid
calling some firmware commands which are not
supported by the AP firmware.

Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: Choose interface specific calls on vif type

Choose interface specific function calls
based on interface type instead of
firmware types.

Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: Add/Del self entry for AP interface only

Add and delete self entry in the firmware sta database
for AP interface only. We do not need such an entry for
STA interface.

Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: Enable hw encryption for STA mode on AP fw

Firmware supports hardware encryption feature
for the station interface running on AP
firmware.

Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: set mac type to MWL8K_MAC_TYPE_SECONDARY_CLIENT

Set mac type for station interface on AP firmware
as secondary. This allows the firmware to set specific
characteristics for the STA interface.

Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: Allow adding station interface on AP firmware

When user wants to add a station interface when
AP firmware is loaded & in-use, allow creating
it and also notify user about the same.

Allow adding max one STA interface for AP fw.

Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: Announce simultaneous AP-STA support on AP fw

Specify the STA support in iface_limit and
in wihpy->interface_modes

Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: Move tx/rx antenna configuration to mwl8k_probe_hw

This avoids calling mwl8k_cmd_rf_antenna functions every
time mwl8k_config function is called.

Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: Do not call mwl8k_cmd_set_rf_channel unconditionally

Avoid calling mwl8k_cmd_set_rf_channel unconditionally
by checking IEEE80211_CONF_CHANGE_CHANNEL.

Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: Stop bsses before hw specific commands

For the commands, that might change the hw characteristics
of the PHY device, stop the running bsses and resume them
once command is complete.

Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: register platform device for parallel flash

Signed-off-by: John W. Linville <linville@tuxdriver.com>

ssb: register platform device for parallel flash

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ssb: trivial: use pflash helper variable

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: allow AP and mesh mode to operate simultaneously

Allow AP and Mesh mode to operate concurrently using
single radio. Verify this using fonera 2.0n featuring
RT3052 chipset and also TP-LINK TL-WN727N featuring
RT5370 chipset.

Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemal.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: remove NOTICE

We use this macro only on 3 places - remove it and replace by other
appropriate macros for printing messages.

Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2800usb: move "TX status missed" messages to debug level

Those messages can flood in dmesg, so do not print them by default.

Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: print warning, notice and info as default

Some messages provide useful information, but are disabled without
CONFIG_RT2X00_DEBUG=y, so enable them by default

Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Update spectral scan output data

The sample data received through the spectral scan can be either in big or
little endian byteorder. This information isn't stored in the output file.
Therefore it is not possible for the analyzer software to find the correct byte
order.

It is relative common to get the data from a low end AP in big endian mode and
transfer it to another computer in little endian mode to analyze it. Therefore,
it would be better to store it in network (big endian) byte order.

The extension of the 8 bit bins for each bin to 16 bit is not necessary. This
operation can be done in userspace or on a different machine. Instead the
max_exp defining the amount of shifting required for each bin is exported to
userspace.

The change of the output format requires a change of the type in the sample
tlv to allow the userspace program to correctly detect the bin format.

Reported-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
[siwu@hrz.tu-chemnitz.de: squashed patches, update commit message, rebase, fix endianess bug]
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: reorder error codes for spectral

When using the spectral scan feature, frames with phy errors are
returned for further processing to the driver. However, if the frames
also have an invalid CRC (which seems to happen quite often), the frame
is marked with bad CRC and not with the PHY error bit. The FFT
processing function will thus miss the frames.

Fix this by changing the precedence in error marking.

Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: drop spectral packets after processing them

Spectral packets are "bogus" packets and should not be further evaluated
by the RX path.

Statistics are added to keep track of these packets.

Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: add debug parameters for spectral scan

Export the various parameters to userspace.

Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: fix invalid access of PCIe RxBD ring buffer descriptor

This patch fixes invalid access of RxBD ring buffer descriptor's
length and flag inside PCIe send_data_complete() routine. We are
supposed to modify TxBD buffer descriptor's length and flag here.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: print chip and firmware version by default

Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net/wireless/iwlegacy/4965-mac.c: adjust duplicate test

Delete successive tests to the same location.  This looks like simple code
duplication.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@s exists@
local idexpression y;
expression x,e;
@@

*if ( \(x == NULL\|IS_ERR(x)\|y != 0\) )
 { ... when forall
   return ...; }
... when != \(y = e\|y += e\|y -= e\|y |= e\|y &= e\|y++\|y--\|&y\)
    when != \(XT_GETPAGE(...,y)\|WMI_CMD_BUF(...)\)
*if ( \(x == NULL\|IS_ERR(x)\|y != 0\) )
 { ... when forall
   return ...; }
// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-john' of git://git./linux/kernel/git/iwlwifi/iwlwifi-next

Merge branch 'for-john' of git://git./linux/kernel/git/jberg/mac80211-next