[PATCH] USB UHCI: Use root-hub IRQs while suspended

This patch, which has as478b as a prerequisite, enables the uhci-hcd
driver to take advantage of root-hub IRQs rather than polling during the
time it is suspended.  (Unfortunately the hardware doesn't support
port-change interrupts while the controller is running.)  It also turns
off the driver's private timer while the controller is suspended, as it
isn't needed then.  The combined elimination of polling interrupts and
timer interrupts ought to be enough to allow some systems to save a
noticeable amount of power while they are otherwise idle.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

[PATCH] USB UHCI: Fix up loose ends

This patch tidies up a few loose ends left by the preceding patches.
It indicates the controller supports remote wakeup whenever the PM
capability is present -- which shouldn't cause any harm if the
assumption turns out to be wrong.  It refuses to suspend the
controller if the root hub is still active, and it refuses to resume
the root hub if the controller is suspended.  It adds checks for a
dead controller in several spots, and it adds memory barriers as
needed to insure that I/O operations are completed before moving on.

Actually I'm not certain the last part is being done correctly.  With
code like this:

outw(..., ...);
mb();
udelay(5);

do we know for certain that the outw() will complete _before_ the
delay begins?  If not, how should this be written?

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

[PATCH] USB UHCI: Add root-hub suspend/resume support

This patch implements (finally!) separate suspend and resume routines
for the root hub and the controller in the UHCI driver.  It also
changes the sequence used to reset the controller during initial
probing, so as to preserve the existing state during a Resume-From-Disk.
(This new sequence is what should be used in the PCI Quirks code for
early USB handoffs, incidentally.)  Lastly it adds a notion of the
controller being "inaccessible" while in a PCI low-power state, when
normal I/O operations shouldn't be allowed.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

[PATCH] USB UHCI: Add root hub states

This patch starts making some serious changes to the UHCI driver.
There's a set of private states for the root hub, and the internal
routines for suspending and resuming work completely differently, with
transitions based on the new states.  Now the driver distinguishes
between a privately auto-stopped state and a publicly suspended state,
and it will properly suspend controllers with broken resume-detect
interrupts instead of resetting them.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

[PATCH] USB UHCI: Minor improvements

This patch makes a few small improvements in the UHCI driver.  Some
code is moved between different source files and a more useful pointer
is passed to a callback routine.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

[PATCH] USB UHCI: subroutine reordering

This patch moves a few subroutines around in the uhci-hcd source file.
Nothing else is changed.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

[PATCH] USB: turn a user mode driver error into a hard error

This patch turns a user mode driver error into a hard error, and updates
the relevant diagnostic slightly to help troubleshooting.  gphoto was
known to have this problem, hopefully it is now fixed (they have had
plenty of warning...)

This had been left as a soft error to give various user mode drivers a
change to be properly fixed, with the statement that starting in about
2.6.10 it would be changed.  It had been mostly safe as a soft error ...
but that can not be guaranteed.  Now that a year has passed, it's time to
really insist that the user mode drivers finally fix their relevant bugs.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

[PATCH] USB: Fix oops at rmmod after failed probe in isp116x-hcd

This patch fixes an oops triggered at rmmod of isp116x-hcd
after the probe() has failed.

Also, it extends the error message printed, if the driver
cannot detect "Chip's Clock Ready" after a software reset.
As Ian Campbell recently reported, this happens if the
chip's H_WAKEUP pin is not pulled low during software reset.
Several people have already had this issue, hence the update
to the error message.

Also, extend the error message about the failed clock
detection after the software reset.

Signed-off-by: Olav Kongas <ok@artecdesign.ee>

[PATCH] USB: Add isp116x-hcd USB host controller driver

This patch provides an "isp116x-hcd" driver for Philips'
ISP1160/ISP1161 USB host controllers.

The driver:
 - is relatively small, meant for use on embedded platforms.
 - runs usbtests 1-14 without problems for days.
 - has been in use by 6-7 different people on ARM and PPC platforms,
   running a range of devices including USB hubs.
 - supports suspend/resume of both the platform device and the root hub;
   supports remote wakeup of the root hub (but NOT the platform device)
   by USB devices.
 - does NOT support ISO transfers (nobody has asked for them).
 - is PIO-only.

Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

[PATCH] USB: omap_udc updates (mostly cleanups)

Various USB patches, mostly for portability:

  - Fifo mode 1 didn't work previously (oopsed), so now it's fixed and
    (why not) defines even more endpoints for composite devices.

  - OMAP 1710 doesn't have an internal transceiver.

  - Small PM update:  if the USB link is suspended, don't disconnect on
    entry to deep sleep.

  - Be more correct about handling zero length control reads.  OMAP
    seems to mis-handle that protocol peculiarity though; best avoided.

  - Platform device resources (for UDC and OTG controllers) now use
    physical addresses, so /proc/iomem is more consistent.

  - Minor cleanups, notably (by volume) for "sparse" NULL warnings.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>

[PATCH] USB: g_file_storage: export "stall" parameter

This patch changes the g_file_storage driver to make the "stall" module
parameter generally available; currently it is available only if the
testing version of the module has been configured.  It also fixes a typo
in a comment -- thanks, Pat!

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

[PATCH] USB: g_file_storage: Consolidate min()s

This patch simplifies the g_file_storage driver by consolidating a bunch
of min() calculations at a single spot.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Merge /pub/scm/linux/kernel/git/davem/net-2.6

Merge master.kernel.org:/home/rmk/linux-2.6-arm

[IPVS]: Fix for overflows

From: <pageexec@freemail.hu>

$subject was fixed in 2.4 already, 2.6 needs it as well.

The impact of the bugs is a kernel stack overflow and privilege escalation
from CAP_NET_ADMIN via the IP_VS_SO_SET_STARTDAEMON/IP_VS_SO_GET_DAEMON
ioctls.  People running with 'root=all caps' (i.e., most users) are not
really affected (there's nothing to escalate), but SELinux and similar
users should take it seriously if they grant CAP_NET_ADMIN to other users.

Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

[PATCH] DM9000 network driver bugfix

This patch fixes two bugs in the dm9000 network driver:

- Don't read one byte too much in 8bit mode.
- release correct resource

Signed-off-by: Jochen Karrer <j.karrer@lightmaze.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>

[PATCH] Documentation/networking/dmfe.txt: Make documentation nicer

Patch indents dmfe.txt to look like other docs.  It adds a tip about CNET
cards using Davicom chipsets.  Also it removes parts where it refers to how
to build driver out-of-kernel which seems to be cruft from times where the
driver was out of the kernel.

Signed-off-by: Ismail Donmez <ismail@kde.org.tr>
Signed-off-by: Domen Puncer <domen@coderock.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>

[PATCH] fealnx.c calls dev_kfree_skb from atomic context

Signed-off-by: Andrew Morton <akpm@osdl.org>

[PATCH] fix int vs. pm_message_t confusion in airo

Fix int vs. pm_message_t confusion in airo. Should change no code.

Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>

[PATCH] defxx: Use irqreturn_t for the interrupt handler

This is a fix for the interrupt handler in the defxx driver to use
irqreturn_t.  Beside the obvious fix of returning a proper status at all,
it actually checks board registers as appropriate for determining if an
interrupt has been recorded in the bus-specific interface logic.

The patch also includes an obvious one-line fix for SET_NETDEV_DEV needed
for the EISA variation, for which I've decided there is no point in sending
separately.

Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>

[PATCH] dmfe warning fix

drivers/net/tulip/dmfe.c: In function `dmfe_parse_srom':
drivers/net/tulip/dmfe.c:1805: warning: passing arg 1 of `__le16_to_cpup' from incompatible pointer type
drivers/net/tulip/dmfe.c:1817: warning: passing arg 1 of `__le32_to_cpup' from incompatible pointer type
drivers/net/tulip/dmfe.c:1817: warning: passing arg 1 of `__le32_to_cpup' from incompatible pointer type

This is basically a guess:

Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>

[PATCH] document that 8139TOO supports 8129/8130

The 8129/8130 support is a sub-option that is not visible if the user
hasn't enabled the 8139 support.

Let's make it a bit easier for users to find the driver for their nic.

Signed-off-by: Adrian Bunk <bunk@stusta.de>

[NETLINK]: Fix two socket hashing bugs.

1) netlink_release() should only decrement the hash entry
   count if the socket was actually hashed.

   This was causing hash->entries to underflow, which
   resulting in all kinds of troubles.

   On 64-bit systems, this would cause the following
   conditional to erroneously trigger:

err = -ENOMEM;
if (BITS_PER_LONG > 32 && unlikely(hash->entries >= UINT_MAX))
goto err;

2) netlink_autobind() needs to propagate the error return from
   netlink_insert().  Otherwise, callers will not see the error
   as they should and thus try to operate on a socket with a zero pid,
   which is very bad.

   However, it should not propagate -EBUSY.  If two threads race
   to autobind the socket, that is fine.  This is consistent with the
   autobind behavior in other protocols.

   So bug #1 above, combined with this one, resulted in hangs
   on netlink_sendmsg() calls to the rtnetlink socket.  We'd try
   to do the user sendmsg() with the socket's pid set to zero,
   later we do a socket lookup using that pid (via the value we
   stashed away in NETLINK_CB(skb).pid), but that won't give us the
   user socket, it will give us the rtnetlink socket.  So when we
   try to wake up the receive queue, we dive back into rtnetlink_rcv()
   which tries to recursively take the rtnetlink semaphore.

Thanks to Jakub Jelink for providing backtraces.  Also, thanks to
Herbert Xu for supplying debugging patches to help track this down,
and also finding a mistake in an earlier version of this fix.

Signed-off-by: David S. Miller <davem@davemloft.net>

[PATCH] net/slip: replace schedule_timeout() with msleep_interruptible()

Use msleep_interruptible() instead of schedule_timeout() to guarantee
the task delays as expected.

[PATCH] drivers/net/ewrk3.c: remove dead code

This patch removes some obviously dead code found by the Coverity
checker.

Signed-off-by: Adrian Bunk <bunk@stusta.de>

[PATCH] drivers/net/skfp/: fix LITTLE_ENDIAN

This patch fixes the LITTLE_ENDIAN #define and a function prototype.

Signed-off-by: Adrian Bunk <bunk@stusta.de>

[PATCH] drivers/net/tokenring/: cleanups

This patch contains the follwing cleanups:
- make needlessly global code static
- remove obsolete Emacs settings

Signed-off-by: Adrian Bunk <bunk@stusta.de>

[ATALK]: Include asm/byteorder.h in linux/atalk.h

We're using __be16 in userland visible types, so we
have to include asm/byteorder.h so that works.

Signed-off-by: David S. Miller <davem@davemloft.net>

[PKTGEN]: Fix random packet sizes causing panic

Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

[PATCH] pcnet_cs.c: IRQ handler optimization

During some performance diagnostics I stumbled on this slightly wasteful
code in pcnet_cs.c which I made the patch included at the bottom for (two
minor comment fixes included).

Improvement:
instead of *always* calculating
lea    0x2c0(%edx),%ebx
and then additionally doing the
mov    %edx,0xc0(%ebx)
addition *if we need it*,

we now do the *whole* calculation of
mov    %edx,0x380(%ebx)
*only* if we need it.
This even manages to save us a whole 16-byte alignment buffer loss
in this compilation case.

Result: slightly improves IRQ handler performance in both shared and
non-shared IRQ case, which should make my rusty P3/700 a slight bit happier.

Thank you for your support,

Andreas Mohr

old asm result (using gcc 3.3.5):

000015a0 <ei_irq_wrapper>:
    15a0:       55                      push   %ebp
    15a1:       89 e5                   mov    %esp,%ebp
    15a3:       53                      push   %ebx
    15a4:       8d 9a c0 02 00 00       lea    0x2c0(%edx),%ebx
    15aa:       e8 fc ff ff ff          call   15ab <ei_irq_wrapper+0xb>
    15af:       83 f8 01                cmp    $0x1,%eax
    15b2:       74 03                   je     15b7 <ei_irq_wrapper+0x17>
    15b4:       5b                      pop    %ebx
    15b5:       5d                      pop    %ebp
    15b6:       c3                      ret
    15b7:       31 d2                   xor    %edx,%edx
    15b9:       89 93 c0 00 00 00       mov    %edx,0xc0(%ebx)
    15bf:       eb f3                   jmp    15b4 <ei_irq_wrapper+0x14>
    15c1:       eb 0d                   jmp    15d0 <ei_watchdog>
    15c3:       90                      nop
    15c4:       90                      nop
    15c5:       90                      nop
    15c6:       90                      nop
    15c7:       90                      nop
    15c8:       90                      nop
    15c9:       90                      nop
    15ca:       90                      nop
    15cb:       90                      nop
    15cc:       90                      nop
    15cd:       90                      nop
    15ce:       90                      nop
    15cf:       90                      nop

000015d0 <ei_watchdog>:

new asm result:

000015a0 <ei_irq_wrapper>:
    15a0:       55                      push   %ebp
    15a1:       89 e5                   mov    %esp,%ebp
    15a3:       53                      push   %ebx
    15a4:       89 d3                   mov    %edx,%ebx
    15a6:       e8 fc ff ff ff          call   15a7 <ei_irq_wrapper+0x7>
    15ab:       83 f8 01                cmp    $0x1,%eax
    15ae:       74 03                   je     15b3 <ei_irq_wrapper+0x13>
    15b0:       5b                      pop    %ebx
    15b1:       5d                      pop    %ebp
    15b2:       c3                      ret
    15b3:       31 d2                   xor    %edx,%edx
    15b5:       89 93 80 03 00 00       mov    %edx,0x380(%ebx)
    15bb:       eb f3                   jmp    15b0 <ei_irq_wrapper+0x10>
    15bd:       8d 76 00                lea    0x0(%esi),%esi

000015c0 <ei_watchdog>:

Signed-off-by: Andrew Morton <akpm@osdl.org>

drivers/net/: Use the DMA_{64,32}BIT_MASK constants

Use the DMA_{64,32}BIT_MASK constants from dma-mapping.h when calling
pci_set_dma_mask() or pci_set_consistent_dma_mask()

This patch includes dma-mapping.h explicitly because it caused errors
on some architectures otherwise.

See http://marc.theaimsgroup.com/?t=108001993000001&r=1&w=2 for details

Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Domen Puncer <domen@coderock.org>

[TCP]: Let TCP_CONG_ADVANCED default to n

It doesn't seem to make much sense to let an "If unsure, say N." option
default to y.

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

[IPV4]: Fix thinko in TCP_CONG_BIC default.

Since it is tristate when we offer it as a choice, we should
definte it also as tristate when forcing it as the default.
Otherwise kconfig warns.

Signed-off-by: David S. Miller <davem@davemloft.net>

[PATCH] arlan: module parameter fixes

Make sure the code compiles with and without ARLAN_ENTRY_EXIT_DEBUGGING.
Only provide parameter descriptions when parameters are defined.
Remove "arlan_"-prefix to shape up built-in parameter names:

arlan.arlan_debug -> arlan.debug
arlan.arlan_EEPROM_bad -> arlan.EEPROM_bad
arlan.arlan_entry_and_exit_debug -> arlan.entry_and_exit_debug
arlan.arlan_entry_debug -> arlan.entry_debug
arlan.arlan_exit_debug -> arlan.exit_debug

Signed-off-by: Magnus Damm <damm@opensource.se>

[PATCH] net/sis900: Use the DMA_32BIT_MASK constant

Use the DMA_32BIT_MASK constant from dma-mapping.h when calling
pci_set_dma_mask() or pci_set_consistent_dma_mask() instead of custom
macros.
This patch includes dma-mapping.h explicitly because it caused errors
on some architectures otherwise.
See http://marc.theaimsgroup.com/?t=108001993000001&r=1&w=2 for details

Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>

Merge /spare/repo/netdev-2.6/ branch 'register-netdev'

Merge /spare/repo/linux-2.6/

8139cp: safer spin loop for get_statistics

The spin loop in 8139cp is limited to 100 iterations when pulling hardware
stats. There is no allowance for processor speed so on a fast machine, the
stats may not be available that fast. Also, if the board doesn't return
soon enough make sure turn the address back off to prevent later updates
when memory has gone away.

gianfar: Update Marvell PHY name

This patch updates the name identifier to list both of the Marvell PHYs
that are supported.

Signed-off-by: Kumar Gala <kumar.gala@freescale.com>

bonding: xor/802.3ad improved slave hash

Add support for alternate slave selection algorithms to bonding
balance-xor and 802.3ad modes.  Default mode (what we have now: xor of
MAC addresses) is "layer2", new choice is "layer3+4", using IP and port
information for hashing to select peer.

Originally submitted by Jason Gabler for balance-xor mode;
modified by Jay Vosburgh to additionally support 802.3ad mode.  Jason's
original comment is as follows:

The attached patch to the Linux Etherchannel Bonding driver modifies the
driver's "balance-xor" mode as follows:

      - alternate hashing policy support for mode 2
        * Added kernel parameter "xmit_policy" to allow the specification
          of different hashing policies for mode 2.  The original mode 2
          policy is the default, now found in xmit_hash_policy_layer2().
        * Added xmit_hash_policy_layer34()

This patch was inspired by hashing policies implemented by Cisco,
Foundry and IBM, which are explained in
Foundry documentation found at:
http://www.foundrynet.com/services/documentation/sribcg/Trunking.html#112750

Signed-off-by: Jason Gabler <jygabler@lbl.gov>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>

bonding: gratuitous ARP

Add support for generating gratuitous ARPs in bonding
active-backup mode when failovers occur.  Includes support for VLAN
tagging the ARPs as needed.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>

Tulip fixes for Cobalt Qube/RaQ

[PATCH] ARM: 2757/1: remove ixdp2400_init_irq from ixdp2800 code

Patch from Lennert Buytenhek

Compiling one kernel that supports both ixdp2400 and ixdp2800 gives
an error, as a copy of the ixdp2400 irq init routing accidentally
ended up in ixdp2800.c somehow.

Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[PATCH] ARM: 2756/1: add ixp2000 msf mapping

Patch from Lennert Buytenhek

Add a mapping for the ixp2400 and ixp2800 msf unit.  The msf is the
ixp2000's 'media and switch fabric' unit, which handles the networking
part of the chip.

Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[PATCH] ARM: 2755/1: describe ixp2000 virtual memory map layout

Patch from Lennert Buytenhek

Add a comment to asm/arch-ixp2000/ixp2000-regs.h describing the
ixp2000 virtual memory map layout.

Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[PATCH] ARM: 2754/1: move ixp2000 VMALLOC_END up

Patch from Lennert Buytenhek

As the ixdp cpld mappings now live at 0xfe000000, we can push
VMALLOC_END upwards to 0xfb000000, where the first iotable mapping
begins.

Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[PATCH] ARM: 2753/1: move ixdp* cpld mappings

Patch from Lennert Buytenhek

All ixdp platforms currently have a cpld mapped in at 0xfafff000.
Since this address is not 1M-aligned, a regular page mapping will be
used instead of a section mapping, which opens up the possibility of
triggering ixp2400 erratum #66 as we only do the XCB=101 workaround
thing for section mappings.
There is still a lot of space higher up in the virtual memory map
for 1M mappings, so move the cpld mapping to 0xfe000000 and make it
1M big so that a section mapping will be used for it.

Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Merge upstream (approx. 2.6.12-git8) into 'janitor' branch of netdev-2.6.

Merge 'drm-3264' branch of /linux/kernel/git/airlied/drm-2.6

Merge 'drm-fixes' branch of /linux/kernel/git/airlied/drm-2.6

[PATCH] ARM: Add SA_TIMER flag to timer interrupts

VST needs to know which timer handler is for the timer interrupt.
Mark all timer interrupts with the SA_TIMER flag.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[PATCH] ppc32: Fix MPC83xx IPIC external interrupt pending register offset

The pending registers for IRQ1-IRQ7 were pointing to the interrupt pending
register instead of the external one.

Signed-off-by: Tony Li <Tony.Li@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] remove redundant info from SubmittingPatches

Since the Trivial Patch Monkey is mentioned both in steps 4.  and 5., I
removed it from step4 (Select e-mail destination), since it should go under
'Select your CC list'.

Signed-off-by: Cosmin Nicolaescu <cos@camelot.homelinux.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] arm: swsusp build fix

Another swsusp fixup.

Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] jffs2 build fix

Missed conversion in the swsusp cleanup.

Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

drm: fix radeon irq properly

After the previous fix in 2.6.12, this patch should properly fix the
radeon IRQ handling code.

From: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>

Fix up try_to_freeze() usage in arch/i386/kernel/signal.c

The parentheses were missing. Noted by Pavel Machek.

Merge Christoph's freeze cleanup patch

[PATCH] Cleanup patch for process freezing

1. Establish a simple API for process freezing defined in linux/include/sched.h:

   frozen(process) Check for frozen process
   freezing(process) Check if a process is being frozen
   freeze(process) Tell a process to freeze (go to refrigerator)
   thaw_process(process) Restart process
   frozen_process(process) Process is frozen now

2. Remove all references to PF_FREEZE and PF_FROZEN from all
   kernel sources except sched.h

3. Fix numerous locations where try_to_freeze is manually done by a driver

4. Remove the argument that is no longer necessary from two function calls.

5. Some whitespace cleanup

6. Clear potential race in refrigerator (provides an open window of PF_FREEZE
   cleared before setting PF_FROZEN, recalc_sigpending does not check
   PF_FROZEN).

This patch does not address the problem of freeze_processes() violating the rule
that a task may only modify its own flags by setting PF_FREEZE. This is not clean
in an SMP environment. freeze(process) is therefore not SMP safe!

Signed-off-by: Christoph Lameter <christoph@lameter.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] schedule the obsolete raw driver for removal

Since kernel 2.6.3 the Kconfig text explicitely stated this driver was
obsolete.

(trolling for IBMers)

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] list_for_each_entry: fs-dquot.c

Make code more readable with list_for_each_entry_safe.

Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Maximilian Attems <janitor@sternwelten.at>
Signed-off-by: Domen Puncer <domen@coderock.org>
Acked-by: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] drivers/char/rio/: kill rio_udelay

There's no need for a function that only calls udelay.

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] MAINTAINERS: document that uclinux-dev@uclinux.org is subscribers-only

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] DCO: use IANA-reserved second level domain name

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] serial/68328serial: replace schedule_timeout() with msleep_interruptible()

Use msleep_interruptible() instead of schedule_timeout() in send_break() to
guarantee the task delays as expected.  Change @duration's units to
milliseconds, and modify arguments in callers appropriately.

Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] serial/68360serial: replace schedule_timeout() with msleep_interruptible()

Use msleep_interruptible() instead of schedule_timeout() in send_break() to
guarantee the task delays as expected.  Change @duration's units to
milliseconds, and modify arguments in callers appropriately.

Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] Remove duplicate file in Documentation/networking

The files wanpipe.txt and wan-router.txt in Documentation/networking contain
the exact same information (diff between the two shows no document is "Linux
WAN Router Utilities Package" and therefor the name wan-router.txt is more
appropriate.

Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] Remove duplicate file in Documentation/networking (00-INDEX)

wanpipe.txt and wan-router.txt in Documentation/networking contain the exact
same information (diff between the two shows no
Documentation/networking/00-INDEX as pointed out by Randy Dunlap.

Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] Remove duplicate file in Documentation/networking (drivers_net_wan_Kconfig)

wanpipe.txt and wan-router.txt in Documentation/networking contain the exact
same information (diff between the two shows no drivers/net/wan/Kconfig.

Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] sound/oss/cmpci: Use the DMA_32BIT_MASK constant

Use the DMA_32BIT_MASK constant from dma-mapping.h when calling
pci_set_dma_mask() or pci_set_consistent_dma_mask() See
http://marc.theaimsgroup.com/?t=108001993000001&r=1&w=2 for details

Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] sound/oss/es1370: Use the DMA_32BIT_MASK constant

Use the DMA_32BIT_MASK constant from dma-mapping.h when calling
pci_set_dma_mask() or pci_set_consistent_dma_mask() See
http://marc.theaimsgroup.com/?t=108001993000001&r=1&w=2 for details

Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] sound/oss/es1371: Use the DMA_32BIT_MASK constant

Use the DMA_32BIT_MASK constant from dma-mapping.h when calling
pci_set_dma_mask() or pci_set_consistent_dma_mask() See
http://marc.theaimsgroup.com/?t=108001993000001&r=1&w=2 for details

Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] sound/oss/esssolo1: Use the DMA_32BIT_MASK constant

Use the DMA_32BIT_MASK constant from dma-mapping.h when calling
pci_set_dma_mask() or pci_set_consistent_dma_mask() See
http://marc.theaimsgroup.com/?t=108001993000001&r=1&w=2 for details

Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] printk: arch/i386/mm/pgtable.c

printk() calls should include appropriate KERN_* constant.

Signed-off-by: Christophe Lucas <clucas@rotomalug.org>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] printk: arch/i386/mm/ioremap.c

printk() calls should include appropriate KERN_* constant.

Signed-off-by: Christophe Lucas <clucas@rotomalug.org>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] Kill signed chars

scripts/ is full of mismatches between char* params an signed char* arguments,
and viceversa.  gcc4 now complaints loud about this.  Patch below deletes all
those 'signed'.

Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] update comment about gzip scratch size

fix a comment about the array size.

Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] ll_merge_requests_fn() cleanup

ll_merge_requests_fn() assigns total_{phys,hw}_segments twice.  Fix this
and a typo.

Signed-off-by: Nikita Danilov <nikita@clusterfs.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] drivers/isdn/hisax/: possible cleanups

This patch contains the following possible cleanups:
- make needlessly global code static
- remove the compiled but unused st5481_hdlc.{c,h}
- kill enternow.h
- enternow_pci.c: kill InByte/OutByte/BYTE
- isdnl2.c: kill FreeSkb
- remove or #if 0 the following unused functions:
  - config.c: IsdnCardState
  - ipacx.c: ipacx_new_ph
  - ipacx.c: dch_bh
  - ipacx.c: setup_ipacx
  - isdnl2.c: IsRR

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Kai Germaschewski <kai@germaschewski.name>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] drivers/cdrom/cm206.c: cleanups

This patch contains the following cleanups:
- make needlessly global functions static
- remove the following unused global function:
  - cm206_delay

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] drivers/char/ip2*: cleanups

This patch contains the following cleanups:
- i2cmd.c: #if 0 the unused function i2cmdUnixFlags
- i2cmd.c: make the needlessly global funciton i2cmdBaudDef static
- ip2main.c: remove dead code that wasn't reachable due to an #ifdef

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] kfree cleanups for drivers/firmware/

Here's a patch with kfree() cleanups for drivers/firmware/efivars.c Patch
removes redundant NULL checks before kfree and also makes a small
whitespace cleanup - moves two statements on same line to separate lines.

Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Acked-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] kfree cleanups in ixj.c

This patch removes redundant checks for NULL pointer before kfree() in
drivers/telephony/

Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] remove pointless NULL check before kfree in sony535.c

There's no need to check for NULL, kfree() can cope.

Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] update Computone MAINTAINERS entry

This patch states that Michael still maintains this driver and removes a no
longer mailing list.

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] i386: cleanup boot_cpu_logical_apicid variables

There are currently two different boot_cpu_logical_apicid variables:
- a global one in mpparse.c
- a static one in smpboot.c

Of these two, only the one in smpboot.c might be used (through
boot_cpu_apicid).

This patch therefore removes the one in mpparse.c .

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrey Panin <pazke@donpac.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] change the SOUND_PRIME handling

SOUND_PRIME (for OSS) is a tristate.

This doesn't make much sense if most users are checking for
SOUND_PRIME!=0.

This patch changes the semantics of SOUND_PRIME to being a limit for all
OSS modules, IOW: SOUND_PRIME=m does now say that all OSS drivers can
only be modular.

As a side effect, since SOUND_PRIME already depends on SOUND, there's no
longer a reason for drivers depending on SOUND_PRIME to additionally
depend on SOUND.

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] drivers/block/ll_rw_blk.c: cleanups

This patch contains the following cleanups:
- make needlessly global code static
- remove the following unused global functions:
  - blkdev_scsi_issue_flush_fn
  - __blk_attempt_remerge
- remove the following unused EXPORT_SYMBOL's:
  - blk_phys_contig_segment
  - blk_hw_contig_segment
  - blkdev_scsi_issue_flush_fn
  - __blk_attempt_remerge

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] drivers/char/mwave/tp3780i.c: remove dead code

This patch removes some dead code found by the Coverity checker.

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] drivers/video/matrox/matroxfb_misc.c: remove dead code

This patch removes some obviously dead code found by the Coverity
checker.

This patch was already ACK'ed by Petr Vandrovec.

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] fs/ncpfs/: remove unused #ifdef USE_OLD_SLOW_DIRECTORY_LISTING code

This patch removes some unused #ifdef USE_OLD_SLOW_DIRECTORY_LISTING
code.

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] fs/jffs/: cleanups

This patch contains the following cleanups:
- make needlessly global functions static
- provide some debugging helper functions only for appropriate
  values of CONFIG_JFFS_FS_VERBOSE

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] drivers/char/rocket.c: cleanups

This patch contains the following cleanups:
- make needlessly global code static
- remove the TRUE/FALSE macros

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] drivers/char/nvram.c: possible cleanups

This patch contains the following possible cleanups:
- make the needlessly global function __nvram_set_checksum static
- #if 0 the unused global function nvram_set_checksum
- remove the EXPORT_SYMBOL's for both functions

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] drivers/char/mwave/3780i.c: cleanups

This patch contains the following cleanups:
- make a needlessly global function static
- #if 0 the unused global function dsp3780I_ReadGenCfg

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] drivers/char/istallion.c: remove an unneeded variable

This patch removes an unneeded global variable.

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] sound/oss/sscape.c: remove dead code

The Coverity checker found that sscape_sb_enable never get's assigned any
value different from 0, and therefore some code paths are impossible.

This patch removes this variable and the dead code paths.

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] drivers/scsi/dpt*: remove version.h dependencies

This patch removes version.h dependencies.

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] cosmetic fixes for example programs in Documentation/cdrom/sbpcd

This patch makes a few minor changes to the example programs in
Documentation/cdrom/sbpcd to kill off some warnings and build failures.

Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] Use ALIGN to remove duplicate code

This patch makes use of ALIGN() to remove duplicate round-up code.

Signed-off-by: Nick Wilson <njw@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>