mac80211: remove redundant monitor_work enqueueing

ieee80211_restart_sta_timer() takes care for enqueueing
monitor_work if needed, so no need to do it again.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: don't queue monitor work for HW_CONNECTION_MONITOR

Devices that monitor the connection in the hw don't need
the monitor work in the driver.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: Fix typo in mac80211_hwsim.c

Correct spelling "occured" to "occurred" in
drivers/net/wireless/mac80211_hwsim.c

Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00:Add RT5372 chipset support

Signed-off-by: John Li <chen-yang.li@mediatek.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: avoid useless cast from (struct ath_rateset *) to (u8 *) and back

Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Fix breakage in debug functions when built as a module

Since commit 481b9606, it has not been possible to invoke debugging
with any rtlwifi driver built as a module.

Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00:Add VCO recalibration

Signed-off-by: John Li <chen-yang.li@mediatek.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix descriptor length for AR9462

Change the descriptor length to 24 and explicitly
set the control field 23 to zero. Not doing so would
result in dropping of frames.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix programming SYNTH4 for AR9462

The LONG_SHIFT_SELECT offset is different for AR9462 from
the other chip families. Fix this.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Initialize NF values properly

Using AR_SREV_* macros for setting up the chip-specific NF
values will make adding support for new chips hard. Use separate
macros for each chip. Currently, AR9462 has the same value for
all NF limits.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Remove unused initvals

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix phyerr debug statistics

Validate the phyerr value against the max. size of the
statistics array properly.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Prettify recv debugfs file output

Dumping the RSSI information in the middle of error
statistics is a bit misleading. Move them to the end.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Add a debugfs file to display reset statistics

Location: <debugfs_path>/ieee80211/phy#/ath9k/reset

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Merge wiphy and misc debugfs files

This patch merges the 'wiphy' and 'misc' debugfs files
and consolidates the information.

Information about the current channel and other HT parameters
can be obtained from both mac80211 and iw. Remove such
redundant data.

The reset statistics have been removed, they will be re-added in
a subsequent patch (in a new debugfs file).

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Remove unnecessary variable initialization

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: remove duplicate initvals

Comparing SHA1 checksums of the initval tables has shown that there are many
tables that are 100% identical.

iniBank{0,1,2,3,7} and iniBB_RfGain are shared by AR5416, AR913x, AR9160
iniBank6 is shared between AR5416 and AR9160
iniBank6TPC is shared between AR913x and AR9160

iniPcieSerdes is the same for all AR9002 based devices

The CCK FIR coefficients are shared between AR9271 and AR9287

Getting rid of those duplicates saves about 7.5k uncompressed (on MIPS).

For AR9003 and later there are some duplicates as well, but I've decided to
leave them in for now, as the initvals for those chips are still actively
maintained by QCA.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Add support for D-Link DWA-127 to rt2800usb.

This is an RT3070 based device.

Cc: <stable@vger.kernel.org>
Reported-by: Mikhail Kryshen <mikhail@kryshen.net>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'wireless-next' of git://git./linux/kernel/git/iwlwifi/iwlwifi

ath9k: remove unnecessary PS wrappers

ath_set_channel is called from ath9k_config which already has proper
PS wrappers

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: remove obsolete comments

the corresponding code/logic was removed in
"ath9k: rework power state handling"

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k:Remove __raw_read and __raw_write

By swithing from our __raw_read and __raw_write functions to ioread32 and iowrite32,
benchmarks on my desk with iperf went from 11MBps to 18.1MBps using the AHB bus
on an EnGenius ECB3500 running OpenWRT.

Signed-off-by: Jonathan Bither <jonbither@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: restructure AP/GO mode API

The AP/GO mode API isn't very clearly defined, it
has "set beacon" and "new beacon" etc.

Modify the API to the following:
 * start AP -- all settings
 * change beacon -- new beacon data
 * stop AP -- stop AP mode operation

This also reflects in the nl80211 API, rename
the commands there correspondingly (but keep
the old names for compatibility.)

Overall, this makes it much clearer what's going
on in the API.

Kalle developed the ath6kl changes, I created
the rest of the patch.

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: remove il_is_rfkill_hw

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: s/il_txq_mem/il_free_txq_mem/g

Previous name was confusing.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: s/S_RF_KILL_HW/S_RFKILL/g

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: small queue initializations cleanup

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: enable only rfkill interrupt when rfkill switch is on during IFF_UP

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: small il4965_set_hw_ready cleanup

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: check correct il_poll_bit error value

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: do not grab nic access if rfkill

If rfkill is on il_grab_nic_access() fail and we can not write to the
various registers during stop procedure. Write to those registers
unconditionally instead.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwleagcy: fix ident code damage

Using ident is not always good.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwleagcy: remove old comments

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: improve mac operation debuggability a bit

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: get rid of tx/rx traffic log

The same data can be gathered using monitor mode.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: merge all ops structures into one

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: merge il_lib_ops into il_ops

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: remove il_apm_ops

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: merge eeprom_ops into lib_ops

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: remove temp_ops

Remove unneeded structure and cleanup temperature calibration routines
a bit.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: move debugfs_ops to il_priv

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: gather all 4965 handlers in one place

Handers belongs logically into 4965-mac.c file.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: regulatory_bands is not an ops

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: use writeb,writel,readl directly

That change will save us some CPU cycles at run time. Having
port-based I/O seems to be not possible for PCIe devices.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: cleanup/fix memory barriers

wmb(), rmb() are not needed when writel(), readl() are used as
accessors for MMIO. We use them indirectly via iowrite32(),
ioread32().

What is needed mmiowb(), for synchronizing writes coming from
different CPUs on PCIe bridge (see in patch comments). This
fortunately is not needed on x86, where mmiowb() is just
defined as compiler barrier. As iwlegacy devices are most likely
not used on anything other than x86, this is not so important
fix.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: always check if got h/w access before write

Before we write to the device register always check if
_il_grap_nic_access() was successful.

Change type return type _il_grap_nic_access() to bool, and
add likely()/unlikely() statements.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlegacy: dump stack when fail to gain access to the device

Print dump stack when the device is not responding. This should give
some more clue about the reason of failure. Also change the message we
print, since "MAC in deep sleep" is kinda confusing.

On the way add unlikely(), as fail to gain NIC access is hmm ...
unlikely.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192se firmware load can overflow target buffer

Define RTL8190_MAX_RAW_FIRMWARE_CODE_SIZE which represents the
maximimum possible firmware file size. Use it in the definition
of the buffer which receives the firmware file data.

Set RTL8190_MAX_RAW_FIRMWARE_CODE_SIZE closer to the actual size of
the firmware file, e.g., 90000 (down from hard coded 164000). The current
size of rtlwifi/rtl8192sefw.bin is 88856.

Set max_fw_size to RTL8190_MAX_RAW_FIRMWARE_CODE_SIZE for the size limit
check. Fix the error case where max_fw_size is not cleared if the size
limit check fails.

Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: make sdio firmware filename specific

The sdio driver part uses firmware name brcmfmac.bin. With addition
of usb this name is too generic. This patch renames the filename
to brcmfmac-sdio.bin.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: add USB support for bcm43235/6/8 chipsets

This patch extends the use of the brcmfmac driver with support for
chipsets with a USB host interface. The first chipsets supported are
the bcm43235, bcm43236, and bcm43238 for which firmware has been
submitted.

This driver change has been successfully built for x86, x86_64,
ppc64, arm_le, and mips_be.

It has been tested successfully on x86 and x86_64.

Cc: M. Lambert <lambertm@westman.wave.ca>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Kan Yan <kanyan@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: use spinlock calls saving irq flags in brcmf_enq_event()

This function is executed within irq context. The call spin_unlock_irq
does enable interrupts which is not desired in the irq context. This patch
replaces them using the spin_loc_irqsave and spin_unlock_irqrestore
functions.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Kan Yan <kanyan@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: change allocation flag in brcmf_enq_event() function

As the function is called from atomic context it should not do the
kzalloc call with GFP_KERNEL.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Kan Yan <kanyan@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: update bus state in common driver part

The bus state is updated in the sdio bus init function, but it is
better to do it when the brcmf_bus_start() function is completed
successfully. The brcmf_netdev_open() function will return -EAGAIN
until the state is updated instead of calling brcmf_bus_start() to
avoid reentering that function.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: only return success in brcmf_sdbrcm_bus_init() when true

The function brcmf_sdbrcm_bus_init() always returned success except for
firmware download failure. However, also when enabling SDIO function 2
is failing the function should return failure. This patch fixes that.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: move module entry points to dhd_linux.c

The module_init/exit functions are moved to dhd_linux.c to prepare
for supporting multiple host interface types.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: use specific types in struct brcmf_bus

The fields bus_priv and drvr are defined as void pointer. It is
preferred to have specific types for compiler type checking. To
prepare for other bus types the bus_priv field is defined as a
union containing the sdio bus private structure reference.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: make sure cancel_work_sync only called after INIT_WORK

INIT_WORK only gets called after brcmf_proto_attach returns
success. This dependency should be annotated in brcmf_detach to
avoid any error.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: resolve smatch issues in brcmfmac code

This patch resolves the following smatch issues:

wl_cfg80211.c +1377 brcmf_cfg80211_connect(65) warn: min_t truncates
here '(sme->ssid_len)' (4294967295 vs 9223372036854775807)
dhd_sdio.c +1275 brcmf_sdbrcm_rxglom(156) warn: min_t truncates here
'(pfirst->len)' (2147483647 vs 4294967295)
dhd_sdio.c +1457 brcmf_sdbrcm_rxglom(338) warn: min_t truncates here
'(pfirst->len)' (2147483647 vs 4294967295)
bcmsdh_sdmmc.c +300 brcmf_sdioh_request_buffer(10) warn: variable
dereferenced before check 'pkt' (see line 295)

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: smac: remove smatch warnings from brcmsmac code

The patch fixes following smatch warnings:

main.c +2902 brcms_b_read_objmem(11) info: ignoring unreachable code.
mac80211_if.c +1146 brcms_suspend(8) error: we previously assumed 'wl'
could be null (see line 1145)
srom.c +641 _initvars_srom_pci(16) error: potential null dereference
'entry'.  (kzalloc returns null)

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: smac: fix endless retry of A-MPDU transmissions

The A-MPDU code checked against a retry limit, but it was using
the wrong variable to do so. This patch fixes this to assure
proper retry mechanism.

This problem had a side-effect causing the mac80211 flush callback
to remain waiting forever as well. That side effect has been fixed
by commit by Stanislaw Gruszka:

commit f96b08a7e6f69c0f0a576554df3df5b1b519c479
Date:   Tue Jan 17 12:38:50 2012 +0100

    brcmsmac: fix tx queue flush infinite loop

    Reference:
    https://bugzilla.kernel.org/show_bug.cgi?id=42576

Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: smac: remove redundant assignments from txpwrctrl_pwr_setup_nphy

The function wlc_phy_txpwrctrl_pwr_setup_nphy() does assign a local
variable target_pwr_qtrdbm in several code paths, but in the end all
code paths are coming to an assignment of that variable which does
override all previous. So those early and redundant assignments have
been removed.

Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: smac: fix unintended fallthru in wlc_phy_radio_init_2057()

The radio initialization for 2057 rev 5 was using the incorrect
register table for the initialization. This patch fixes that.

Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: update the maintainers listed for brcm80211 drivers

Henry Ptasinski is not working on the brcm80211 driver so taking
his name/email out of the MAINTAINERS file.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Correcting typos in rtlwifi/base.c

This patch correct some typos in a comment.

Signed-off-by: Tristan Pourcelot <tristan.pourcelot@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192c-common: rtl8192se: rtl8192de: Simplify if statements

Devendra Naga <devendra.aaru@gmail.com> submitted a patch for rtl8192c_common
to change the tests in _rtl92c_store_pwrIndex_diffrate_offset(). This patch
improves on those changes and applies similar modifications to drivers rtl8192se
and rtl8192de.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00:Add debug message for new chipset

Signed-off-by: John Li <chen-yang.li@mediatek.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00:Fix typo

Signed-off-by: John Li <chen-yang.li@mediatek.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi/rtl8192c: in _rtl92c_phy_calculate_bit_shift remove comparing bitmask against 1

in _rtl92c_phy_calculate_bit_shift everytime the right shifted bitmask
is AND with 1 and compared against 1. i.e.
       if ((bitmask >> i) & 0x1 == 1)
               break;
which in the if condition is anyway becomes a 1 or 0.

Signed-off-by: Devendra.Naga <devendra.aaru@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-linville' of git://git./linux/kernel/git/luca/wl12xx

iwlwifi: enable receiving beacons when not associated

If the firmware implements beacon filtering,
beacons are filtered when not associated. This causes
association failures on channels marked passive.

Enabling this flag indicates to the firmware to allow
the beacons to pass through when not associated only.

Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: remove un-necessary return

Already return 0, change to void

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: SRAM size moves from hw_params to cfg

This will allow to set the hw_params after we fetch the uCode.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: save ucode capabilities in iwl_fw

The capabilities parsed from the ucode file are never saved.  Save
them in the iwl_fw structure.

Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: changes args to iwl_nic for firmware operations

Remove the references to iwl_priv from the firmware request and
parsing routines.  They are generic to the nic.

Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: the transport knows its state

This allows to handle races such as Tx packets on their way to be
sent although the transport has been stopped already.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: move event and err pointers to iwl_nic

Move the ucode offset pointers to the iwl_nic as they are nic related.

Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: document the transport layer

Fix a few typos in the existing comments too.
Enforce the comments with might_sleep.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: send testmode hcmd reply with rx header

When a host command is sent through testmode, the whole
reply (including rx header) is returned to the user, and not
only the payload of the rx.
Before this commit the length was buggy - the reply contained 4 bytes
after the end of the payload.

Signed-off-by: Amit Beka <amit.beka@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: fixes to testmode indirect access

Fixed casting of buffer addressing, and added size to
the read method, like in __iwl_read_prph.

Signed-off-by: Amit Beka <amit.beka@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: use enhance_sensitivity from iwl_fw

Remove another dependency between the nic layer and the iwl_priv
struct.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: iwl_set_hw_params returns always 0

Remove the return value.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: kill iwl_down and s/__iwl_down/iwl_down

iwl_down was just a wrapper around __iwl_down which was called from
one place only. Replace it to direct call to iwl_down. Add lockdep
warning in iwl_down to ensure it was called with the mutex held.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: change args to ucode routines

Change the prameters to the ucode (de)allocate routines to iwl_nic as
they are not transport operations.

Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: Move ucode pointers to iwl_fw

The ucode image is a ucode related thing not a transport one.  Move them.

Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: move firmware_loading_complete to iwl_nic

Move firmware_loading_complete from iwl_priv to iwl_nic and rename it
to more accurately reflect what it does.

Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: move firmware_name to iwl_nic

Delete firmware_name from iwl_priv and use iwl_nic instead.

Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: move fw_index from iwl_priv to iwl_nic

Delete fw_index from iwl_priv and use iwl_nic instead.

Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: move ucode_ver to iwl_nic

Delete ucode_ver from iwl_priv and use iwl_nic instead.

Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: create iwl_nic structure

Create iwl_nic structure and link it together.

Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: give PCIe its own lock

Instead of using a global lock, the PCIe transport
can use an own lock for its IRQ. This will make it
possible to not disable IRQs for the shared lock.
The lock is currently used throughout the code but
this can be improved even further by splitting up
the locking for the queues.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>

iwlwifi: move workqueue to priv

In order to separate the different parts of the
driver better, we are reducing the shared data.
This moves the workqueue to "priv", and removes
it from the transport. To do this, simply use
schedule_work() in the transport.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: trace debug messages

Make iwlwifi record all debug messages into
tracing, even if debug_level is not enabled.
Due to the lack of APIs, the debug messages
are now recorded up to a max length of 100,
the only one above that is the RXON which is
not needed if you trace the commands as well
as it only dumps the command contents.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>

iwlwifi: added reply data to testmode HCMD send

The testmode command for host command send now replies
with a nl80211 message and the response it recieved from
the device.

This does not change the API directly, but adds a reply
to the testmode call.

Signed-off-by: Amit Beka <amit.beka@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: testmode new indirect RW API

Replaced the old SRAM and periphery indirect access functions
with a unified indirect memory access functions. These include
new IWL_TM_CMDs for buffer read/write/dump which replace the
SRAM read/dump commands, but the API for IWL_TM_CMD_INDIRECT_REG
read/write will now not be supported (returns error).

This also handles writing to periphery registers in 1-3 bytes.

Requires the corresponding patch in the library for the API change.

Signed-off-by: Amit Beka <amit.beka@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: log as error when error detected

A lot of error conditions in testmode log as IWL_DEBUG_INFO which is not
logged by default. Change it

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless

Conflicts:
net/mac80211/debugfs_sta.c
net/mac80211/sta_info.h

ath9k: stop on rates with idx -1 in ath9k rate control's .tx_status

Rate control algorithms are supposed to stop processing when they
encounter a rate with the index -1.  Checking for rate->count not being
zero is not enough.

Allowing a rate with negative index leads to memory corruption in
ath_debug_stat_rc().

One consequence of the bug is discussed at
https://bugzilla.redhat.com/show_bug.cgi?id=768639

Signed-off-by: Pavel Roskin <proski@gnu.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: clear previous security setting during association

Driver maintains different flags for WEP, WPA, WPA2 security modes.
Appropriate flag is set using security information provided in
connect request. mwifiex_is_network_compatible() routine uses them
to check if driver's setting is compatible with AP. Association is
aborted if the routine fails.

For some corner cases, it is observed that association is failed
even for valid security information based on association history.
This patch fixes the problem by clearing previous security setting
during each association.

We should set WEP key provided in connect request as default tx key.
This missing change is also added here.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: do not call rate control .tx_status before .rate_init

Most rate control implementations assume .get_rate and .tx_status are only
called once the per-station data has been fully initialized.
minstrel_ht crashes if this assumption is violated.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: call rate control only after init

There are situations where we don't have the
necessary rate control information yet for
station entries, e.g. when associating. This
currently doesn't really happen due to the
dummy station handling; explicitly disabling
rate control when it's not initialised will
allow us to remove dummy stations.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>