John Crispin [Thu, 10 Mar 2016 19:10:58 +0000 (19:10 +0000)]
brcm63xx: fix BCM3368 interrupt controller addresses
Looks like the addresses for BCM3368 were wrongly defined when DT
support was introduced.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 48980
John Crispin [Thu, 10 Mar 2016 19:10:54 +0000 (19:10 +0000)]
brcm63xx/lzma-loader: fix O32 ABI conformance
According to the calling convention of the o32 ABI the caller
function must reserve stack space for $a0-$a3 registers in case
the callee needs to save its arguments.
The assembly code of the loader does not reserve stack space for
these registers thus when the 'loader_main' function needs to save
its arguments, those will be stored in the 'workspace' area instead
of the stack.
Because the workspace area is also used by other part of the code, the
saved register values gets overwritten and this often leads to failed
kernel boots.
Fix the code to reserve stack space for the registers to avoid this
error.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
[noltari: apply the fix for brcm63xx too]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 48979
John Crispin [Thu, 10 Mar 2016 19:10:48 +0000 (19:10 +0000)]
tools/flock: fix compile on Alpine Linux
fixes build errors:
src/flock.c:208:34: error: 'O_NOCTTY' undeclared (first use in this function)
fd = open(filename, O_RDONLY|O_NOCTTY|O_CREAT, 0666);
src/flock.c:208:43: error: 'O_CREAT' undeclared (first use in this function)
fd = open(filename, O_RDONLY|O_NOCTTY|O_CREAT, 0666);
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 48978
John Crispin [Thu, 10 Mar 2016 19:07:26 +0000 (19:07 +0000)]
ar71xx: add support for the Telldus TellStick ZNet Lite
Signed-off-by: Micke Prag <micke.prag@telldus.se>
SVN-Revision: 48977
John Crispin [Thu, 10 Mar 2016 19:07:17 +0000 (19:07 +0000)]
base-files: add function ucidef_set_interface_raw to enable default configuration on interfaces other than lan and wan.
Signed-off-by: Micke Prag <micke.prag@telldus.se>
SVN-Revision: 48976
Rafał Miłecki [Wed, 9 Mar 2016 06:34:29 +0000 (06:34 +0000)]
brcm47xx: image: move disabled devices to the new building system
This only drops WGR614 V9 which has 2 MiB flash and it's unlikely to get
any interest.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48975
Rafał Miłecki [Wed, 9 Mar 2016 06:34:25 +0000 (06:34 +0000)]
brcm47xx: image: switch Linksys WRT54G3GV2-VF to the new building system
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48974
Rafał Miłecki [Tue, 8 Mar 2016 18:33:25 +0000 (18:33 +0000)]
brcm47xx: image: switch Netgear WGT634U to the new building system
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48973
Rafał Miłecki [Tue, 8 Mar 2016 18:33:22 +0000 (18:33 +0000)]
brcm47xx: image: switch rest of 64k block devices to the new building system
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48972
Rafał Miłecki [Tue, 8 Mar 2016 18:33:19 +0000 (18:33 +0000)]
brcm47xx: image: switch Motorola devices to the new building system
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48971
Rafał Miłecki [Tue, 8 Mar 2016 18:33:16 +0000 (18:33 +0000)]
brcm47xx: image: switch D-Link DWL-3150 to the new building system
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48970
John Crispin [Tue, 8 Mar 2016 18:12:02 +0000 (18:12 +0000)]
openvpn: add support for X.509 name options
x509-username-field was added in OpenVPN 2.2, and verify-x509-name was
added in 2.3. This fixes ticket #18807.
Signed-off-by: Jeffery To <jeffery.to@gmail.com>
SVN-Revision: 48969
John Crispin [Tue, 8 Mar 2016 18:11:59 +0000 (18:11 +0000)]
ramips: add support for Planex MZK-WDPR.
add support for Planex MZK-WDPR.
MZK-WDPR(MZK-WDPR-R01) is internet radio tuner.
This patch is "network board" in MZK-WDPR.
LCD board is non OpenWrt Platform.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 48968
John Crispin [Tue, 8 Mar 2016 18:11:55 +0000 (18:11 +0000)]
brcm2708: add Raspberry Pi 3 support
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 48967
John Crispin [Tue, 8 Mar 2016 18:11:49 +0000 (18:11 +0000)]
brcm2708: update linux 4.4 patches to latest version
As usual these patches were extracted from the raspberry pi repo:
https://github.com/raspberrypi/linux/tree/rpi-4.4.y
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 48966
John Crispin [Tue, 8 Mar 2016 18:11:40 +0000 (18:11 +0000)]
brcm2708-gpu-fw: update to latest version
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 48965
John Crispin [Tue, 8 Mar 2016 18:11:37 +0000 (18:11 +0000)]
include: add Cortex-A53 CPU_TYPE
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 48964
Rafał Miłecki [Tue, 8 Mar 2016 11:05:10 +0000 (11:05 +0000)]
bcm53xx: update bcm47xx_sprom to the latest 4.6 queued version
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48963
Rafał Miłecki [Tue, 8 Mar 2016 08:29:32 +0000 (08:29 +0000)]
bcm53xx: fix SPROM driver compilation with ssb/bcma as module
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48962
Rafał Miłecki [Tue, 8 Mar 2016 08:29:29 +0000 (08:29 +0000)]
bcm53xx: revert patch removing imprecise abort workaround
It seems it still happens on some devices.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48961
Rafał Miłecki [Mon, 7 Mar 2016 23:09:26 +0000 (23:09 +0000)]
kernel: backport bcma 4.6 changes for flashes
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48960
Rafał Miłecki [Mon, 7 Mar 2016 22:37:09 +0000 (22:37 +0000)]
mac80211: backport brcmfmac patchset with driver setting concept
This prepares brcmfmac for better country handling and fixes BCM4360
support which was always failing with:
[ 13.249195] brcmfmac: brcmf_pcie_download_fw_nvram: FW failed to initialize
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48959
Felix Fietkau [Mon, 7 Mar 2016 21:00:58 +0000 (21:00 +0000)]
mt76: update to the latest version, adds some mt7603/mt7628 fixes
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 48958
Felix Fietkau [Mon, 7 Mar 2016 21:00:49 +0000 (21:00 +0000)]
musl: update to latest git, adds some fixes for the mips64 port and regular expressions
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 48957
Felix Fietkau [Mon, 7 Mar 2016 21:00:46 +0000 (21:00 +0000)]
kernel: add MIPS kernel fix for an uninitialized CPU map
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 48956
Felix Fietkau [Mon, 7 Mar 2016 17:56:58 +0000 (17:56 +0000)]
kernel: remove linux 4.3 support
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 48955
Felix Fietkau [Mon, 7 Mar 2016 17:56:53 +0000 (17:56 +0000)]
ramips: convert the remaining subtargets to 4.4
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 48954
Felix Fietkau [Mon, 7 Mar 2016 17:05:03 +0000 (17:05 +0000)]
ramips: fix subtarget kernel version assignment (only mt7621 is ready for now)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 48953
Felix Fietkau [Mon, 7 Mar 2016 16:35:43 +0000 (16:35 +0000)]
ubox: update to the latest version, fixes an error on processing invalid modules
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 48952
Felix Fietkau [Mon, 7 Mar 2016 16:33:34 +0000 (16:33 +0000)]
ramips: add linux 4.4 support, update mt7621 subtarget to 4.4
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 48951
Felix Fietkau [Mon, 7 Mar 2016 14:34:14 +0000 (14:34 +0000)]
bsdiff: add missing host build dependency on bzip2 (fixes #21990)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 48950
Felix Fietkau [Mon, 7 Mar 2016 11:03:44 +0000 (11:03 +0000)]
lantiq: print profile name in dsl lucistat
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48949
Felix Fietkau [Mon, 7 Mar 2016 11:03:41 +0000 (11:03 +0000)]
ltq-vdsl-app: do not set the reserved bit 4 in the xTSE 8
I do not know if this causes any problems now, but we should not set
it, because it is reserved. Some more recent versions of the Lantiq DSL
API driver and Control is checking if only valid bits are set.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48948
Felix Fietkau [Mon, 7 Mar 2016 11:03:38 +0000 (11:03 +0000)]
ltq-vdsl-app: make it possible to configure ADSL/VDSL independently
There are some cases where ISPs are running ATM over VDSL or PTM over
ADSL, this is not the common case, but these cases exist. Make it
possible to configure OpenWrt for such cases by adding a new config
option line_mode.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48947
Felix Fietkau [Mon, 7 Mar 2016 11:03:35 +0000 (11:03 +0000)]
ltq-vdsl-app: sync annex option between from ADSL package
The detailed annex option were only available in the danube DSL app
including the activation of G.992.2 Annex A (ADSL Lite). This is now
also added to the vdsl app for the vrx200.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48946
Felix Fietkau [Mon, 7 Mar 2016 11:03:32 +0000 (11:03 +0000)]
ltq-adsl-app: sync annex option between from VDSL package
The adsl control app missed the activation of annex M and annex L in
the Annex A part, this now activates everything the firmware supports.
In Annex L type only the wide US (Mask1) was activated, now also the
narrow US (Mask2) version gets activated.
In addition annex J was also added.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48945
Felix Fietkau [Mon, 7 Mar 2016 11:03:29 +0000 (11:03 +0000)]
base-files: change type of adsl and vdsl to dsl only
Instead of having two different types adsl and vdsl just create one dsl
type. This way we can use the same luci code for adsl and vdsl and the
config parameters are not so different.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48944
Felix Fietkau [Mon, 7 Mar 2016 11:03:26 +0000 (11:03 +0000)]
ltq-vdsl-app: make the dsl_control application stop cleanly
I am not calling dsl_cmd because I want to ignore the lock, quit
should also be send when someone else is accessing it. I saw that some
other call was stuck here and all following calls were stuck in the
dsl_cmd lock.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48943
Felix Fietkau [Mon, 7 Mar 2016 11:03:21 +0000 (11:03 +0000)]
lantiq: add dsl firmware to default packages
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48942
Felix Fietkau [Mon, 7 Mar 2016 11:03:18 +0000 (11:03 +0000)]
lantiq: do not set default firmware file
We are now shipping a DSL firmware, do not set it by default to some
file name.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48941
Felix Fietkau [Mon, 7 Mar 2016 11:03:13 +0000 (11:03 +0000)]
ltq-vdsl-app: load the vrx200 firmware or patch it
This checks for the VRX firmware provided in the OpenWrt package.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48940
Felix Fietkau [Mon, 7 Mar 2016 11:03:09 +0000 (11:03 +0000)]
dsl-vrx200-firmware-xdsl: create Lantiq vrx200 firmware patches
Instead of having two big binaries only add one binary and then a patch
to create the other one when needed at runtime.
This is easier to handle in one Makefile for both firmware files.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 48939
Felix Fietkau [Mon, 7 Mar 2016 09:20:22 +0000 (09:20 +0000)]
mac80211: rework gpio chip/button support to build on platforms without CONFIG_GPIOLIB
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 48938
Felix Fietkau [Mon, 7 Mar 2016 08:45:01 +0000 (08:45 +0000)]
ar71xx: fix qca956x ethernet initialization
Complete internal switch initialization for QCA956X.
Set default mdio device if the interface mode of GE0 is not SGMII (fix ticket #21520).
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
SVN-Revision: 48937
Felix Fietkau [Sun, 6 Mar 2016 19:40:31 +0000 (19:40 +0000)]
ar71xx: enable USB packages for WNR2200 (fixes #21984)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 48936
Rafał Miłecki [Sun, 6 Mar 2016 18:08:03 +0000 (18:08 +0000)]
bcm53xx: use SPROM driver queued for 4.6
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48935
Felix Fietkau [Sat, 5 Mar 2016 21:07:18 +0000 (21:07 +0000)]
prereq: stop relying on man pages and grep for --recursive on the git-submodule script directly (fixes #21968)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 48934
Hauke Mehrtens [Sat, 5 Mar 2016 17:51:37 +0000 (17:51 +0000)]
kernel: update kernel 4.4 to version 4.4.4
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48933
Hauke Mehrtens [Sat, 5 Mar 2016 17:49:09 +0000 (17:49 +0000)]
kernel: mpc85xx: fix build of kmod-usb2-fsl
Fix buildbot error for mpc85xx.
ehci-fsl.ko should be packaged inside the usb2 package, because it
depends on the ehci kernel module. The fsl-mph-dr-of.ko module can stay
in an own package because the ehci driver depends on it.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48932
Hauke Mehrtens [Sat, 5 Mar 2016 16:23:50 +0000 (16:23 +0000)]
kernel: fix section mismatch in crashlog
The function memblock_insert_region() is in the section
__init_memblock, also put crashlog_init_memblock there.
This fixes this section mismatch warning:
The function memblock_insert_region.isra.1() references
the function __meminit crashlog_init_memblock().
This is often because memblock_insert_region.isra.1 lacks a __meminit
annotation or the annotation of crashlog_init_memblock is wrong.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48931
Hauke Mehrtens [Sat, 5 Mar 2016 16:23:19 +0000 (16:23 +0000)]
spi-gpio-custom: fix section mismatch
This fixes this section mismatch warning:
The function spi_gpio_custom_get_slave_cs() references
the variable __initdata bus_nump.
This is often because spi_gpio_custom_get_slave_cs lacks a __initdata
annotation or the annotation of bus_nump is wrong.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48930
Hauke Mehrtens [Sat, 5 Mar 2016 16:22:45 +0000 (16:22 +0000)]
kernel: add missing config options
The buildbots complained about these config options being missing for arm64:
CONFIG_DUMMY_CONSOLE_COLUMNS=80
CONFIG_DUMMY_CONSOLE_ROWS=25
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48929
Felix Fietkau [Sat, 5 Mar 2016 14:23:49 +0000 (14:23 +0000)]
uclibc++: add a patch to fix memory corruption issues on exceptions
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 48928
Felix Fietkau [Sat, 5 Mar 2016 13:37:02 +0000 (13:37 +0000)]
build: fix git prereq check to forcibly disable man pagers on the --help check
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 48927
Felix Fietkau [Sat, 5 Mar 2016 10:49:59 +0000 (10:49 +0000)]
build: fix git prereq check to not rely on being in a git directory (#21968)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 48926
Felix Fietkau [Sat, 5 Mar 2016 09:45:15 +0000 (09:45 +0000)]
ar71xx: WNR612v2: enable control of all LEDs and buttons
This patch provides full GPIO support for WNR612v2 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48924
Felix Fietkau [Sat, 5 Mar 2016 09:45:10 +0000 (09:45 +0000)]
ar71xx: WNR2000v3: add speed_mask to Ethernet port LED initialization
This patch add speed_mask parameter to Ethernet port LED initialization
during system startup. LEDs are configured to show amber light for 10 Mbps
link and green for 100 Mbps as described on device label.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48923
Felix Fietkau [Sat, 5 Mar 2016 09:45:06 +0000 (09:45 +0000)]
ar71xx: WNR2000v3: enable control of all LEDs and buttons
This patch provides full GPIO support for WNR2000v3 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48922
Felix Fietkau [Sat, 5 Mar 2016 09:45:03 +0000 (09:45 +0000)]
mac80211: ath9k: enable GPIO buttons
Enable platform-defined GPIO button support for ath9k device.
Key poller is activated for attached platform buttons.
Requires ath9k GPIO chip access.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48921
Jo-Philipp Wich [Fri, 4 Mar 2016 18:37:45 +0000 (18:37 +0000)]
netifd: fix build error
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 48920
Jo-Philipp Wich [Fri, 4 Mar 2016 17:48:18 +0000 (17:48 +0000)]
netifd: fix VTI ikey/okey endianess
Ensure that ikey and okey are sent in network byte order to the kernel.
Also don't mangle external IP addrs and routes when reconfiguring iinterfaces.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 48919
Jo-Philipp Wich [Fri, 4 Mar 2016 11:20:11 +0000 (11:20 +0000)]
buildroot: apply IGNORE_ERRORS to host builds
Apply the error ignore mechanism to host builds as well in order to skip over
broken feed packages.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 48918
John Crispin [Fri, 4 Mar 2016 08:33:41 +0000 (08:33 +0000)]
opkg: Fix handling of sha256sums for conffiles
MD5s are shorter than SHA256, so reading buffer has to be bigger to read the
whole hash.
Signed-off-by: Michal Hrusecky <michal.hrusecky@nic.cz>
SVN-Revision: 48917
John Crispin [Fri, 4 Mar 2016 08:33:38 +0000 (08:33 +0000)]
AP121 target: fix board detection in ar71xx.sh
Signed-off-by: Attila Lendvai <attila@lendvai.name>
SVN-Revision: 48916
John Crispin [Fri, 4 Mar 2016 08:33:36 +0000 (08:33 +0000)]
procd: Allow to configure default respawn retry count
Extend /etc/config/system with a parameter to set the
default respawn retry for procd launched services that
have respawn enabled.
config service
option respawn_retry -1
All services that don't specify specific respawn parameters
will get their defaults added by procd.sh. If respawn_retry
is specified in /etc/config/system the default retry limit
will be set to this value by procd.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
SVN-Revision: 48915
John Crispin [Fri, 4 Mar 2016 08:33:33 +0000 (08:33 +0000)]
AR8216: improve mmd register access
Combine all bus operations for one MMD access in one function.
Protecting all these bus operations with one lock also helps
to avoid potential issues due to bus operations intercepting
the register and data write.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 48914
John Crispin [Fri, 4 Mar 2016 08:33:30 +0000 (08:33 +0000)]
AR8216: make ARL age time configurable
The default TTL for address resolution table entries is 5 minutes
for all members of the AR8216 family. This can cause issues if
e.g. Wifi clients roam to another AP and their MAC appears on
another switch port suddenly. Then the client may not be reachable
until the old ARL entry expires.
I would have expected the switch to invalidate old entries if it
detects the same MAC on another port. But that's not the case.
Therefore make the TTL for ARL entries configurable.
The effective TTL will always be a multiple of 7 seconds.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 48913
John Crispin [Fri, 4 Mar 2016 08:33:28 +0000 (08:33 +0000)]
AR8216: remove redundant port number in MIB header line
The line before includes the port number anyway so there's no need
to duplicate the port number in the MIB info header.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 48912
John Crispin [Fri, 4 Mar 2016 08:33:25 +0000 (08:33 +0000)]
AR8216: complement MIB counters with info in GiB / MiB / KiB
The decimal values especially for TxByte and RxGoodByte are hard to read
once bigger amounts of data have been transferred.
Therefore complement the decimal values with info in GiB / MiB / KiB.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 48911
John Crispin [Fri, 4 Mar 2016 08:33:22 +0000 (08:33 +0000)]
AR8216: don't display MIB counters if all are empty
For unused switch ports all MIB values are zero. Displaying ~40 empty
MIB counters is just confusing and makes it hard to read the output of
swconfig dev <dev> show.
Therefore, if all MIB counters for a port are zero, just display
an info that the MIB counters are empty.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 48910
John Crispin [Fri, 4 Mar 2016 08:33:20 +0000 (08:33 +0000)]
imx6: image: Add missing kernel prefix
Signed-off-by: Petr Štetiar <ynezz@true.cz>
SVN-Revision: 48909
John Crispin [Fri, 4 Mar 2016 08:33:17 +0000 (08:33 +0000)]
ramips: mt7621: fix WF-2881 for ubi split
This patch fix firmware split for WF-2881 which was previously manually partitioned.
Signed-off-by: YounJae Rho <luxflow@live.com>
SVN-Revision: 48908
John Crispin [Fri, 4 Mar 2016 08:33:14 +0000 (08:33 +0000)]
lua: host: install lnum_config.h
One of the host patches introduces the new header file lnum_config.h
included by luaconf.h, but doesn't install it.
Install it to allow building C modules for the host Lua.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 48907
John Crispin [Fri, 4 Mar 2016 08:33:12 +0000 (08:33 +0000)]
ramips: Add profiles for JCG routers
This patch adds profiles and support for building factory and
sysupgrade images for JHR-N805R, JHR-N825R and JHR-N926R.
Signed-off-by: Reinhard Max <reinhard@m4x.de>
Reviewed-by: Torsten Duwe <duwe@lst.de>
SVN-Revision: 48906
John Crispin [Fri, 4 Mar 2016 08:33:09 +0000 (08:33 +0000)]
ramips: Add JCG routers to base-files
This patch adds support for JHR-N805R, JHR-N825R and JHR-N926R to
various scripts in the base-files directory.
Signed-off-by: Reinhard Max <reinhard@m4x.de>
Reviewed-by: Torsten Duwe <duwe@lst.de>
SVN-Revision: 48905
John Crispin [Fri, 4 Mar 2016 08:33:06 +0000 (08:33 +0000)]
ramips: Add device tree for JCG JHR-N926R
Add a device tree for JCG JHR-N825R
This router is based on a RT3052 and has 4MB of CFI flash and 32MB of
SDRAM. As a special feature, it comes with a two digit seven segment
display that is connected to a pair of daisy-chained 74164 shift
registers that can be controlled via GPIOs.
For details, see https://wikidevi.com/wiki/JCG_JHR-N825R .
Signed-off-by: Reinhard Max <reinhard@m4x.de>
Reviewed-by: Torsten Duwe <duwe@lst.de>
SVN-Revision: 48904
John Crispin [Fri, 4 Mar 2016 08:33:03 +0000 (08:33 +0000)]
ramips: Add device tree for JCG JHR-N825R
Add a device tree for JCG JHR-N825R
This router is based on a RT3052 and has 4MB of CFI flash and 32MB of
SDRAM. For details, see https://wikidevi.com/wiki/JCG_JHR-N825R .
Signed-off-by: Reinhard Max <reinhard@m4x.de>
Reviewed-by: Torsten Duwe <duwe@lst.de>
SVN-Revision: 48903
John Crispin [Fri, 4 Mar 2016 08:33:00 +0000 (08:33 +0000)]
ramips: Add device tree for JCG JHR-N805R
Add a device tree for JCG JHR-N805R
This router is based on a RT3050 and has 4MB of SPI flash and 16MB of
SDRAM. For details, see https://wikidevi.com/wiki/JCG_JHR-N805R .
Signed-off-by: Reinhard Max <reinhard@m4x.de>
Reviewed-by: Torsten Duwe <duwe@lst.de>
SVN-Revision: 48902
John Crispin [Fri, 4 Mar 2016 08:32:54 +0000 (08:32 +0000)]
ramips: Add a tool to create JCG factory images
replace spaces with tabs
Signed-off-by: Reinhard Max <reinhard@m4x.de>
SVN-Revision: 48901
Felix Fietkau [Thu, 3 Mar 2016 22:29:00 +0000 (22:29 +0000)]
mac80211: improve rate control performance
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 48897
Felix Fietkau [Thu, 3 Mar 2016 22:01:06 +0000 (22:01 +0000)]
mt76: update to the latest version, adds stability fixes
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 48895
John Crispin [Thu, 3 Mar 2016 20:24:47 +0000 (20:24 +0000)]
kernel: gpio-button-hotplug: Add missing ONESHOT flag to threaded IRQ request
Without the IRQF_ONESHOT flag in devm_request_threaded_irq() call I get
following error:
genirq: Threaded irq requested with handler=NULL and !ONESHOT for irq 56
gpio-keys gpio-keys: failed to request irq:56 for gpio:20
>From kernel/irq/manage.c:
The interrupt was requested with handler = NULL, so we use the default
primary handler for it. But it does not have the oneshot flag set. In
combination with level interrupts this is deadly, because the default
primary handler just wakes the thread, then the irq lines is reenabled,
but the device still has the level irq asserted. Rinse and repeat....
While this works for edge type interrupts, we play it safe and reject
unconditionally because we can't say for sure which type this interrupt
really has. The type flags are unreliable as the underlying chip
implementation can override them.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
SVN-Revision: 48894
John Crispin [Thu, 3 Mar 2016 20:24:45 +0000 (20:24 +0000)]
ramips: Incorrect file mode change
Commit
d0f5ab6d95a1 ("ramips: Added support for ZBT-826 / ZBT-1026")
incorrectly changed the mode of the ramips shell scripts from 755 to 644.
I.e., they are not excutable any more and for example devices will be left
with broken configs.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
SVN-Revision: 48893
John Crispin [Thu, 3 Mar 2016 20:24:41 +0000 (20:24 +0000)]
target/mpc85xx: check for 'generic' subtarget for initramfs image file
Copy 'cuImage.tl-wdr4900-v1-initramfs' only for the 'generic' subtarget.
This is a follow-up to:
http://git.openwrt.org/?p=openwrt.git;a=commitdiff;h=
b889fe55c1844aec2c03da28fecb03e958c21f18
We build our initramfs images more rarely, so it took a while
to catch this too.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
SVN-Revision: 48892
John Crispin [Thu, 3 Mar 2016 20:24:38 +0000 (20:24 +0000)]
mtd: fix reading of image magic bytes in smaller chunks
The image_check currently fails when it cannot read all magic bytes in a
single chunk. But this can happen when the data are read from a pipe. This
currently breaks the openmesh.sh upgrade script with musl because it uses
dd with a blocksize of 1 to copy the image file to the mtd process.
The read can simply be repeated until enough bytes are read for the magic
byte check. It only stops when either an error was returned or 0 bytes were
read.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 48891
John Crispin [Thu, 3 Mar 2016 20:24:35 +0000 (20:24 +0000)]
om-watchdog: Move each board name to its own line
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 48890
John Crispin [Thu, 3 Mar 2016 20:24:33 +0000 (20:24 +0000)]
om-watchdog: Stop om-watchdog via procd before rebooting
It was noticed that the system can hang during the reboot before the kernel
actually triggers the system reset and before all processes are stopped. The
watchdog didn't automatically restart the system because the om-watchdog
process was still running and triggering the hardware watchdog.
Instead the system should stop the watchdog during the shutdown to get the
benefit of an hardware reset in case of an software related problem. This stop
can be done quite easily with procd because it keeps track of its started
processes.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 48889
John Crispin [Thu, 3 Mar 2016 20:24:30 +0000 (20:24 +0000)]
ramips: Add a tool to create JCG factory images
This tool creates factory images for JCG routers.
Details can be found in the header comment of jcgimage.c.
Signed-off-by: Reinhard Max <reinhard@m4x.de>
Reviewed-by: Torsten Duwe <duwe@lst.de>
SVN-Revision: 48888
Felix Fietkau [Wed, 2 Mar 2016 17:40:58 +0000 (17:40 +0000)]
ramips: enable mt76 on mt7688 by default
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 48886
Felix Fietkau [Wed, 2 Mar 2016 17:40:55 +0000 (17:40 +0000)]
mt76: update to the latest version, adds basic mt7628 support
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 48885
Felix Fietkau [Wed, 2 Mar 2016 14:56:48 +0000 (14:56 +0000)]
mac80211: add a number of pending fixes
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 48883
Felix Fietkau [Wed, 2 Mar 2016 14:56:43 +0000 (14:56 +0000)]
mac80211: refresh patch
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 48882
Felix Fietkau [Wed, 2 Mar 2016 13:22:51 +0000 (13:22 +0000)]
mac80211: ath9k: enable access to GPIO
Enable access to GPIO chip and its pins for Atheros AR92xx
wireless devices. For now AR9285 and AR9287 are supported.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Acked-by: Hartmut Knaack <knaack.h@gmx.de>
SVN-Revision: 48881
Felix Fietkau [Wed, 2 Mar 2016 13:22:46 +0000 (13:22 +0000)]
mac80211: ath9k: set default state for platform LEDs
Support default state for platform LEDs connected to ath9k device.
Now LEDs are correctly set on or off at ath9k module initialization.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Acked-by: Hartmut Knaack <knaack.h@gmx.de>
SVN-Revision: 48880
Felix Fietkau [Wed, 2 Mar 2016 13:22:40 +0000 (13:22 +0000)]
mac80211: ath9k: enable platform WLAN LED name
Enable platform-supplied WLAN LED name for ath9k device.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Acked-by: Hartmut Knaack <knaack.h@gmx.de>
SVN-Revision: 48879
Jo-Philipp Wich [Wed, 2 Mar 2016 10:01:27 +0000 (10:01 +0000)]
cyassl: disable Intel ASM for now
With ASM support enabled, CyaSSL fails to build on all x86 subtargets.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 48876
Hauke Mehrtens [Tue, 1 Mar 2016 23:16:17 +0000 (23:16 +0000)]
kernel: update kernel 3.18 to version 3.18.27
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48874
Jo-Philipp Wich [Tue, 1 Mar 2016 14:31:08 +0000 (14:31 +0000)]
openssl: update to 1.0.2g (8 CVEs)
CVE-2016-0704
s2_srvr.c overwrite the wrong bytes in the master-key when applying
Bleichenbacher protection for export cipher suites. This provides a
Bleichenbacher oracle, and could potentially allow more efficient variants of
the DROWN attack.
CVE-2016-0703
s2_srvr.c did not enforce that clear-key-length is 0 for non-export ciphers.
If clear-key bytes are present for these ciphers, they *displace* encrypted-key
bytes. This leads to an efficient divide-and-conquer key recovery attack: if
an eavesdropper has intercepted an SSLv2 handshake, they can use the server as
an oracle to determine the SSLv2 master-key, using only 16 connections to the
server and negligible computation. More importantly, this leads to a more
efficient version of DROWN that is effective against non-export ciphersuites,
and requires no significant computation.
CVE-2016-0702
A side-channel attack was found which makes use of cache-bank conflicts on
the Intel Sandy-Bridge microarchitecture which could lead to the recovery of
RSA keys. The ability to exploit this issue is limited as it relies on an
attacker who has control of code in a thread running on the same hyper-
threaded core as the victim thread which is performing decryptions.
CVE-2016-0799
The internal |fmtstr| function used in processing a "%s" format string in
the BIO_*printf functions could overflow while calculating the length of a
string and cause an OOB read when printing very long strings. Additionally
the internal |doapr_outch| function can attempt to write to an OOB memory
location (at an offset from the NULL pointer) in the event of a memory
allocation failure. In 1.0.2 and below this could be caused where the size
of a buffer to be allocated is greater than INT_MAX. E.g. this could be in
processing a very long "%s" format string. Memory leaks can also occur.
The first issue may mask the second issue dependent on compiler behaviour.
These problems could enable attacks where large amounts of untrusted data is
passed to the BIO_*printf functions. If applications use these functions in
this way then they could be vulnerable. OpenSSL itself uses these functions
when printing out human-readable dumps of ASN.1 data. Therefore applications
that print this data could be vulnerable if the data is from untrusted sources.
OpenSSL command line applications could also be vulnerable where they print out
ASN.1 data, or if untrusted data is passed as command line arguments. Libssl is
not considered directly vulnerable. Additionally certificates etc received via
remote connections via libssl are also unlikely to be able to trigger these
issues because of message size limits enforced within libssl.
CVE-2016-0797
In the BN_hex2bn function the number of hex digits is calculated using an int
value |i|. Later |bn_expand| is called with a value of |i * 4|. For large
values of |i| this can result in |bn_expand| not allocating any memory because
|i * 4| is negative. This can leave the internal BIGNUM data field as NULL
leading to a subsequent NULL ptr deref. For very large values of |i|, the
calculation |i * 4| could be a positive value smaller than |i|. In this case
memory is allocated to the internal BIGNUM data field, but it is insufficiently
sized leading to heap corruption. A similar issue exists in BN_dec2bn. This
could have security consequences if BN_hex2bn/BN_dec2bn is ever called by user
applications with very large untrusted hex/dec data. This is anticipated to be
a rare occurrence. All OpenSSL internal usage of these functions use data that
is not expected to be untrusted, e.g. config file data or application command
line arguments. If user developed applications generate config file data based
on untrusted data then it is possible that this could also lead to security
consequences. This is also anticipated to be rare.
CVE-2016-0798
The SRP user database lookup method SRP_VBASE_get_by_user had confusing memory
management semantics; the returned pointer was sometimes newly allocated, and
sometimes owned by the callee. The calling code has no way of distinguishing
these two cases. Specifically, SRP servers that configure a secret seed to hide
valid login information are vulnerable to a memory leak: an attacker connecting
with an invalid username can cause a memory leak of around 300 bytes per
connection. Servers that do not configure SRP, or configure SRP but do not
configure a seed are not vulnerable. In Apache, the seed directive is known as
SSLSRPUnknownUserSeed. To mitigate the memory leak, the seed handling in
SRP_VBASE_get_by_user is now disabled even if the user has configured a seed.
Applications are advised to migrate to SRP_VBASE_get1_by_user. However, note
that OpenSSL makes no strong guarantees about the indistinguishability of valid
and invalid logins. In particular, computations are currently not carried out
in constant time.
CVE-2016-0705
A double free bug was discovered when OpenSSL parses malformed DSA private keys
and could lead to a DoS attack or memory corruption for applications that
receive DSA private keys from untrusted sources. This scenario is considered
rare.
CVE-2016-0800
A cross-protocol attack was discovered that could lead to decryption of TLS
sessions by using a server supporting SSLv2 and EXPORT cipher suites as a
Bleichenbacher RSA padding oracle. Note that traffic between clients and non-
vulnerable servers can be decrypted provided another server supporting SSLv2
and EXPORT ciphers (even with a different protocol such as SMTP, IMAP or POP)
shares the RSA keys of the non-vulnerable server. This vulnerability is known
as DROWN (CVE-2016-0800). Recovering one session key requires the attacker to
perform approximately 2^50 computation, as well as thousands of connections to
the affected server. A more efficient variant of the DROWN attack exists
against unpatched OpenSSL servers using versions that predate 1.0.2a, 1.0.1m,
1.0.0r and 0.9.8zf released on 19/Mar/2015 (see CVE-2016-0703 below). Users can
avoid this issue by disabling the SSLv2 protocol in all their SSL/TLS servers,
if they've not done so already. Disabling all SSLv2 ciphers is also sufficient,
provided the patches for CVE-2015-3197 (fixed in OpenSSL 1.0.1r and 1.0.2f)
have been deployed. Servers that have not disabled the SSLv2 protocol, and are
not patched for CVE-2015-3197 are vulnerable to DROWN even if all SSLv2
ciphers are nominally disabled, because malicious clients can force the use of
SSLv2 with EXPORT ciphers. OpenSSL 1.0.2g and 1.0.1s deploy the following
mitigation against DROWN: SSLv2 is now by default disabled at build-time.
Builds that are not configured with "enable-ssl2" will not support SSLv2.
Even if "enable-ssl2" is used, users who want to negotiate SSLv2 via the
version-flexible SSLv23_method() will need to explicitly call either of:
SSL_CTX_clear_options(ctx, SSL_OP_NO_SSLv2); or SSL_clear_options(ssl,
SSL_OP_NO_SSLv2); as appropriate. Even if either of those is used, or the
application explicitly uses the version-specific SSLv2_method() or its client
or server variants, SSLv2 ciphers vulnerable to exhaustive search key recovery
have been removed. Specifically, the SSLv2 40-bit EXPORT ciphers, and SSLv2
56-bit DES are no longer available. In addition, weak ciphers in SSLv3 and up
are now disabled in default builds of OpenSSL. Builds that are not configured
with "enable-weak-ssl-ciphers" will not provide any "EXPORT" or "LOW" strength
ciphers.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 48868
John Crispin [Tue, 1 Mar 2016 09:17:12 +0000 (09:17 +0000)]
opkg: Make opkg understand old md5
Opkg now uses sha256 by default and expects them. Making it optionally
understand md5s also and detect md5 sum so we can migrate from configuration
that used md5.
Signed-off-by: Michal Hrusecky <Michal.Hrusecky@nic.cz>
SVN-Revision: 48867
John Crispin [Tue, 1 Mar 2016 09:17:09 +0000 (09:17 +0000)]
ar71xx: Add OOLITE to the Gainstrong profile, removed standalone profile.
This patch moves the OOLITE profile code into the overarching Gainstrong
profile and deletes the old single profile file.
Signed-off by: Stijn Segers <francesco.borromini@inventati.org>
SVN-Revision: 48866