Felix Fietkau [Thu, 12 Mar 2015 16:21:53 +0000 (16:21 +0000)]
ath9k: fix a beacon enable handling bug
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 44696
Felix Fietkau [Thu, 12 Mar 2015 15:27:44 +0000 (15:27 +0000)]
kernel: backport fib_trie improvements/fixes from 4.0-rc
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 44695
John Crispin [Thu, 12 Mar 2015 10:07:01 +0000 (10:07 +0000)]
uClibc: fix syscall() for syscalls with 6 arguments on PowerPC
Patch from the uClibc master.
Fixes the package fastd on PowerPC.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 44694
John Crispin [Thu, 12 Mar 2015 10:06:53 +0000 (10:06 +0000)]
ar71xx: Ext LNA patch for TUBE2H and HORNET-UB targets
Signed-off-by: Christophe Prévotaux <c.prevotaux@rural-networks.com>
SVN-Revision: 44693
John Crispin [Thu, 12 Mar 2015 10:06:42 +0000 (10:06 +0000)]
ar71xx: Hornet UB GPIO WPS/Reset
This problem has existed at least since Attitude Adjustment and
is also present in trunk. Basically on the Hornet-UB board the
functionality of RESET and WPS have "switched places".
There are two tickets about the issue at dev.openwrt.org,
The solution suggested on them both is incomplete though
and introduces the following proglem:
Patching as suggested on #14136/#15282 will result in a situation
where simply pressing the RESET button on the bottom will cause
FACTORY RESET to be run. This is due to GPIO high/low state being
incorrect as a result of the above change and virtually the RESET
button is in the pressed-down state the entire time. When it is
then physically pressed, that causes the opposite, release, to be
triggered and since to the board it seemed that the button was
pressed long before it was released, the FACTORY RESET results.
The attached patch works as expected. I have verified both the
incorrect functionality as well as after fixing the issue as
described in the patch and flashing the resulting firmware to a
Hornet-UB board.
Signed-off-by: Janne Cederberg <janne.cederberg@gmail.com>
SVN-Revision: 44692
John Crispin [Thu, 12 Mar 2015 10:06:31 +0000 (10:06 +0000)]
ralink: resize the flash partition for FireWRT
Signed-off-by: wengbj <fl.service@t-firefly.com>
SVN-Revision: 44691
John Crispin [Thu, 12 Mar 2015 10:06:17 +0000 (10:06 +0000)]
ralink: MT7621 add i2c controller driver
ralink i2c driver is not working on MT7621 platform. Porting a new drivers from MTK's source code.
Signed-off-by: daixj <fl.service@t-firefly.com>
SVN-Revision: 44690
John Crispin [Thu, 12 Mar 2015 10:06:08 +0000 (10:06 +0000)]
lldpd: add support for 'readonly_mode'
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
SVN-Revision: 44689
John Crispin [Thu, 12 Mar 2015 10:06:01 +0000 (10:06 +0000)]
modules: set dwc2 gadget dependency for at91
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44688
John Crispin [Thu, 12 Mar 2015 10:05:54 +0000 (10:05 +0000)]
acx-mac80211: fails to build on cobalt
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44687
John Crispin [Thu, 12 Mar 2015 10:05:48 +0000 (10:05 +0000)]
cobalt: framebuffer device has moved
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44686
Mirko Vogt [Thu, 12 Mar 2015 00:39:50 +0000 (00:39 +0000)]
disable silent-rules by default
OpenWrt hides verbose output by default,
regardless of automake silent-rules being en-/disabled.
If we enable verbose output for package builds (V=s)
however, we'd like to see as most as possible.
Signed-off-by: Mirko Vogt <mirko@openwrt.org>
SVN-Revision: 44685
Mirko Vogt [Thu, 12 Mar 2015 00:39:48 +0000 (00:39 +0000)]
Do not use $(V) - force AM_V=1
Projects using silent-rules might otherwise fail to compile.
This is due to the following resulting Makefile code:
AM_V_P = $(am__v_P_$(V))
am__v_P_ = $(am__v_P_$(AM_DEFAULT_VERBOSITY))
am__v_P_0 = false
am__v_P_1 = :
Automake directly uses $(V) for variable name expansion
which fails if $(V) is set to sth. else other than '0' or '1'.
This patch forces automake to not take $(V) into account
but to always use the default config for verbosity.
A better approach would be to actually take $(V) into account,
however not just pass it through (AM_V='$(V)') but
set AM_V to 0 if $V=0 / unset and to 1 otherwise.
This plan however is foiled due to my frustration about
automake as well as my lack of m4 skills.
automake bug report: http://debbugs.gnu.org/cgi/bugreport.cgi?bug=20077
Signed-off-by: Mirko Vogt <mirko@openwrt.org>
SVN-Revision: 44684
John Crispin [Wed, 11 Mar 2015 17:58:53 +0000 (17:58 +0000)]
modules: make dwc2 only depend on gadget support for brcm2708
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44683
John Crispin [Wed, 11 Mar 2015 17:58:47 +0000 (17:58 +0000)]
uhttp: update to latest git HEAD
this add json-c 0.12, sorry forgot to push this earlier today
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44682
Felix Fietkau [Wed, 11 Mar 2015 17:32:29 +0000 (17:32 +0000)]
kernel: backport symbol export from r44653 to 3.14
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 44681
Rafał Miłecki [Wed, 11 Mar 2015 17:32:02 +0000 (17:32 +0000)]
bcm53xx: fixup early device id 8012
Looks like the BCM53012 has a similar problem to the BCM53011.
Signed-off-by: Ian Kent <raven@themaw.net>
SVN-Revision: 44680
Rafał Miłecki [Wed, 11 Mar 2015 17:10:19 +0000 (17:10 +0000)]
bcm53xx: fix typo in bcm47xx sprom driver
Fix thinko' in the bcm47xx sprom driver.
Signed-off-by: Ian Kent <raven@themaw.net>
SVN-Revision: 44679
John Crispin [Wed, 11 Mar 2015 17:08:46 +0000 (17:08 +0000)]
kenrel: refresh patches
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44678
John Crispin [Wed, 11 Mar 2015 17:08:40 +0000 (17:08 +0000)]
lantiq: make the new dwc2 support only work for vr9
danube needs to be added
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44677
John Crispin [Wed, 11 Mar 2015 17:08:32 +0000 (17:08 +0000)]
lantiq: Convert Zyxel P-2812HNU-FX and TP-Link TD-W8970 to support dwc2
Here the device tree entry for ifxhcd is listed as compatible with one
supported in dwc2 (after patching the dwc driver appropriately).
A second entry is added to support the second core of the hcd. This
entry is listed to be compatible with only dwc2. Done this way there
should be backwards support for both hcd drivers (ltq-hcd and dwc2)
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
SVN-Revision: 44676
John Crispin [Wed, 11 Mar 2015 17:08:26 +0000 (17:08 +0000)]
lantiq: Use platform endianness when accessing dwc2 registers
This patch switches calls to readl/writel to their
dwc2_readl/dwc2_writel equivalents which preserve platform endianness.
This patch is necessary to access dwc2 registers correctly on big
endian systems such as the mips based SoCs made by Lantiq. Then dwc2
can be used to replace ifx-hcd driver for Lantiq platforms found e.g.
in OpenWrt.
The patch was autogenerated with the following commands:
$EDITOR core.h
sed -i "s/\<readl\>/dwc2_readl/g" *.c hcd.h hw.h
sed -i "s/\<writel\>/dwc2_writel/g" *.c hcd.h hw.h
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
SVN-Revision: 44675
John Crispin [Wed, 11 Mar 2015 17:08:15 +0000 (17:08 +0000)]
lantiq: Add sensible hw-defaults for dwc2
Lantiq driver does not work with autodetected fifo sizes so use ones
from original ltq-hcd driver in dwc2. Other values can be
autodetected.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
SVN-Revision: 44674
John Crispin [Wed, 11 Mar 2015 17:08:08 +0000 (17:08 +0000)]
lantiq: Configure gpio power output pin when initializing dwc2 usb
Port gpio code from original ltq-hcd driver to dwc2.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
SVN-Revision: 44673
John Crispin [Wed, 11 Mar 2015 17:08:02 +0000 (17:08 +0000)]
lantiq: Add usb initialization bits from ltq-hcd to platform init
Add VR9 specific usb initialization bits from ltq-hcd to platform
initialization.
This patch is more of a proof-of-concept than production quality
since the initialization registers are different on other lantiq
platforms.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
SVN-Revision: 44672
John Crispin [Wed, 11 Mar 2015 16:41:58 +0000 (16:41 +0000)]
ipset: Bump to 6.24
Included you'll find a patch to bump ipset to version 6.24. This
version supports the ip,fwmark set, which is needed for mwan3 1.6.
Signed-off-by: Jeroen Louwes <jeroen.louwes@gmail.com>
SVN-Revision: 44671
Felix Fietkau [Wed, 11 Mar 2015 16:36:35 +0000 (16:36 +0000)]
mac80211: add missing header file
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 44670
Felix Fietkau [Wed, 11 Mar 2015 16:25:09 +0000 (16:25 +0000)]
mac80211: remove obsolete patches
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 44669
John Crispin [Wed, 11 Mar 2015 16:22:01 +0000 (16:22 +0000)]
cobalt: rename config file
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44668
John Crispin [Wed, 11 Mar 2015 15:56:51 +0000 (15:56 +0000)]
rpcd: update to latest git HEAD
adds 3 fixes from luka
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44666
John Crispin [Wed, 11 Mar 2015 15:56:34 +0000 (15:56 +0000)]
ar71xx: improve WD's My Net Wi-fi Range Extender image creation
Previously, the generated images for the My Net Wi-fi Range Extender
wouldn't always work (and panic) due to the fixed mtd offsets and
sizes for the kernel and rootfs. This patch fixes the problem by
utilizing the shared Cybertan's partition parser to recalculate
the mtd partitions for every image dynamically everytime.
Reported-by: Pascal Paradis <peparadis@yahoo.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44665
John Crispin [Wed, 11 Mar 2015 15:56:27 +0000 (15:56 +0000)]
ar71xx: generalize cybertan partition parser
By removing the NL16 signature check, the parser can be
utilized by other devices like the WD My Net Wi-fi Range
Extender.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44664
John Crispin [Wed, 11 Mar 2015 15:56:15 +0000 (15:56 +0000)]
ar71xx: rename wrt160nl's trx partition parser
This patch renames the partition parser from
wrt160nl to more generic cybertan.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44663
John Crispin [Wed, 11 Mar 2015 15:55:55 +0000 (15:55 +0000)]
ar71xx: fix WRT160NL and TP-Link partition parser patches
405-mtd-tp-link-partition-parser.patch was updating the
WRT160NL's partition parser Kconfig. This patch moves the
relevant change into the right file:
404-mtd-wrt160nl-trx-parser.patch
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44662
John Crispin [Wed, 11 Mar 2015 15:55:28 +0000 (15:55 +0000)]
ralink: FireWRT flash size is up to 16M.
Signed-off-by: wengbj <fl.service@t-firefly.com>
SVN-Revision: 44661
John Crispin [Wed, 11 Mar 2015 15:55:16 +0000 (15:55 +0000)]
ralink: add FireWRT IO multiplexing
Signed-off-by: wengbj <fl.service@t-firefly.com>
SVN-Revision: 44660
John Crispin [Wed, 11 Mar 2015 15:55:06 +0000 (15:55 +0000)]
ar71xx: fix switched WLAN LEDs on TP-LINK Archer C5/C7
ath10k is loaded before ath9k, so the 5GHz adapter becomes phy0.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 44659
John Crispin [Wed, 11 Mar 2015 15:54:52 +0000 (15:54 +0000)]
Fix 3.18.8 breakage of UBI devices with EOF marker (e.g. WNDR4300)
This commit re-adds a patch from 3.14 that is required for UBI block
devices with an EOF marker to be successfully mounted.
Signed-off-by: Oliver Smith <oliver@8.c.9.b.0.7.4.0.1.0.0.2.ip6.arpa>
SVN-Revision: 44658
John Crispin [Wed, 11 Mar 2015 15:54:33 +0000 (15:54 +0000)]
json-c: update to 0.12 and bump all depending services
Version 0.12 deprecates json_object_object_get and moves the header files around
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44657
Felix Fietkau [Wed, 11 Mar 2015 15:02:54 +0000 (15:02 +0000)]
mac80211: Use newer firmware for ath10k
Patch by Bryan Forbes <bryan@reigndropsfall.net>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 44656
Felix Fietkau [Wed, 11 Mar 2015 15:02:47 +0000 (15:02 +0000)]
mac80211: update to wireless-testing 2015-03-09
Based on patch by Bryan Forbes <bryan@reigndropsfall.net>
Also update mt76 to update for API changes
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 44655
Felix Fietkau [Wed, 11 Mar 2015 15:02:32 +0000 (15:02 +0000)]
iw: update to 3.17
Patch by Bryan Forbes <bryan@reigndropsfall.net>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 44654
Felix Fietkau [Wed, 11 Mar 2015 15:02:16 +0000 (15:02 +0000)]
kernel: backport an export required by newer compat-wireless versions
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 44653
Imre Kaloz [Wed, 11 Mar 2015 12:20:03 +0000 (12:20 +0000)]
ppc44x: use the mtdsplit framework for the Taishan
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 44652
Luka Perkov [Tue, 10 Mar 2015 23:43:25 +0000 (23:43 +0000)]
base-files: firstboot: pass down arguments such as -y to jffs2reset
This brings back old behavior.
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 44651
John Crispin [Tue, 10 Mar 2015 20:19:54 +0000 (20:19 +0000)]
ar71xx: fix gpio-latch driver
gpio api has changed. the remove call no longer returns a value.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44650
Luka Perkov [Tue, 10 Mar 2015 16:11:44 +0000 (16:11 +0000)]
ar71xx: refresh patches
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 44649
Luka Perkov [Tue, 10 Mar 2015 16:11:39 +0000 (16:11 +0000)]
ar71xx: wpj588: add missing usb support
Signed-off-by: Luka Perkov <luka@openwrt.org>
Tested-By: Christian Mehlis <christian@m3hlis.de>
SVN-Revision: 44648
John Crispin [Tue, 10 Mar 2015 13:26:50 +0000 (13:26 +0000)]
ar71xx: Fix LED polarity for the TP-LINK TL-MR13U.
Please also backport to Barrier Breaker (this same patch applies there too).
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 44647
John Crispin [Tue, 10 Mar 2015 13:26:44 +0000 (13:26 +0000)]
ar71xx: Fix board detection for the TP-LINK TL-MR13U.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 44646
John Crispin [Tue, 10 Mar 2015 13:08:17 +0000 (13:08 +0000)]
kernel: fix yaffs compile for >= v3.16
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44643
John Crispin [Tue, 10 Mar 2015 11:03:16 +0000 (11:03 +0000)]
ralink: add missing symbol that broke full builds
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44642
John Crispin [Tue, 10 Mar 2015 11:03:10 +0000 (11:03 +0000)]
kirkwood: add missing symbol that broke full builds
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44641
John Crispin [Tue, 10 Mar 2015 11:03:04 +0000 (11:03 +0000)]
au1000: build fails if the input layer is not selected
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44640
John Crispin [Tue, 10 Mar 2015 11:02:52 +0000 (11:02 +0000)]
ipq806x: add 2 missing symbols that broke a full build
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44639
John Crispin [Tue, 10 Mar 2015 11:02:45 +0000 (11:02 +0000)]
ar7: register_mtd_parser() does no longer have a return value
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44638
Imre Kaloz [Tue, 10 Mar 2015 10:00:41 +0000 (10:00 +0000)]
ppc44x: upgrade and switch to 3.18
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 44637
Steven Barth [Tue, 10 Mar 2015 08:43:54 +0000 (08:43 +0000)]
6rd: make host dependency more specific
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 44636
Steven Barth [Tue, 10 Mar 2015 08:43:40 +0000 (08:43 +0000)]
6in4: make host dependency more specific
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 44635
Nicolas Thill [Mon, 9 Mar 2015 22:07:05 +0000 (22:07 +0000)]
ebtables: revert "disable rpath" (closes: #19088)
This reverts commit
9340723d70bce9d905c3f53b2bf415963153b34d.
Signed-off-by: Nicolas Thill <nico@openwrt.org>
SVN-Revision: 44634
John Crispin [Mon, 9 Mar 2015 14:07:30 +0000 (14:07 +0000)]
kmod-usb-dwc2: depends on udc-core (kmod-usb-gadget)
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 44633
John Crispin [Mon, 9 Mar 2015 14:07:14 +0000 (14:07 +0000)]
lantiq: ltq-ptm-{ar9, ase, xway}: fix alloc_netdev for 3.18
buildbot complained about
ifxmips_ptm_adsl.c:1445:70: error: macro "alloc_netdev" requires 4 arguments, but only 3 given
g_net_dev[i] = alloc_netdev(0, g_net_dev_name[i], ether_setup);
^
fix that similar to the change made to ltq_ptm_vdsl.c
compile tested only.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 44632
John Crispin [Mon, 9 Mar 2015 14:07:06 +0000 (14:07 +0000)]
ncm, qmi, mbim: Add dependency on wwan package
The wwan package holds the hotplug script to set mobile broadband
interfaces (un)available. Add it as a dependency to comgt-ncm,
uqmi and umbim.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 44631
John Crispin [Mon, 9 Mar 2015 14:06:50 +0000 (14:06 +0000)]
ncm: Remove unnecessary proto_set_available commands
Interface should not be set unavailable in all error cases,
returning 1 is enough.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 44630
John Crispin [Mon, 9 Mar 2015 14:06:30 +0000 (14:06 +0000)]
wwan: Improve USB modem hotplug script
Adds ncm proto to the list of checked protocols, sets interfaces
unavailable on device removal and removes the unnecessary ifup
command.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 44629
John Crispin [Mon, 9 Mar 2015 14:06:20 +0000 (14:06 +0000)]
comgt, wwan: Move USB data files to wwan package
USB modem data files should be a part of the wwan package, which
actually uses them unlike comgt.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 44628
Nicolas Thill [Mon, 9 Mar 2015 02:02:50 +0000 (02:02 +0000)]
util-linux: fix pkgconfig files
Upstream choose to not rely on configure.ac and recursively expand paths in pkgconfig files at make time,
leading to absolute /usr/include & /usr/lib in there... And we don't want that when cross-compiling...
Signed-off-by: Nicolas Thill <nico@openwrt.org>
SVN-Revision: 44627
Rafał Miłecki [Sat, 7 Mar 2015 12:31:42 +0000 (12:31 +0000)]
bcm53xx: fix printing NAND controller revision
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 44622
Imre Kaloz [Fri, 6 Mar 2015 18:57:49 +0000 (18:57 +0000)]
mvebu: add backported patch to reenable hw i/o coherency
Reported-by: Claudio Leite <leitec@staticky.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 44621
Luka Perkov [Fri, 6 Mar 2015 14:41:57 +0000 (14:41 +0000)]
ar71xx: add support for compex wpj558
OpenWrt can be flashed with following uboot commands:
tftpboot 0x80500000 openwrt-ar71xx-generic-wpj558-16M-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 44620
Steven Barth [Fri, 6 Mar 2015 14:41:07 +0000 (14:41 +0000)]
odhcpd: improvements for DHCPv4 and compile fixes
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 44619
John Crispin [Fri, 6 Mar 2015 07:57:10 +0000 (07:57 +0000)]
openssl: enable ARM assembly acceleration
Tested myself on ixp4xx and mvebu, and (originally)
by Daniel on i.MX6. Also tested on a MIPS target,
to make sure the change to ASFLAGS does not break things.
Based on a patch submitted by Daniel Drown:
https://lists.openwrt.org/pipermail/openwrt-devel/2014-July/026639.html
Signed-off-by: Claudio Leite <leitec@staticky.com>
Signed-off-by: Daniel Drown <dan-openwrt@drown.org>
SVN-Revision: 44618
John Crispin [Fri, 6 Mar 2015 07:57:03 +0000 (07:57 +0000)]
swconfig: fix build with linux 4.0
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 44617
John Crispin [Fri, 6 Mar 2015 07:56:58 +0000 (07:56 +0000)]
ipq806x: rename patches in patches-3.18
This will allow ipq806x to support multiple kernel version more easily.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 44616
John Crispin [Fri, 6 Mar 2015 07:56:47 +0000 (07:56 +0000)]
kernel: move KERNFS to generic config
KERNFS symbol is selected by SYSFS, so place it in generic config.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44615
John Crispin [Fri, 6 Mar 2015 07:56:34 +0000 (07:56 +0000)]
kernel: disable ARCH_NEEDS_CPU_IDLE_COUPLED
Disable ARCH_NEEDS_CPU_IDLE_COUPLED by-default in generic config, since
only one platfrom (omap) needs them.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44614
John Crispin [Fri, 6 Mar 2015 07:56:21 +0000 (07:56 +0000)]
kernel: disbale HAMRADIO in generic config
HAMRADIO enabled in all generic configs, but no one platform directly
use related drivers/protocols. This symbol is only used for kmod-ax25
package modules. Furthermore, half of platforms explicitly disables
this symbol, what silently disables build of modules for kmod-ax25
package.
So disable HAMRADIO by-default in generic config, add it to kmod-ax25
package and remove it from platform specific configs.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44613
John Crispin [Fri, 6 Mar 2015 07:56:08 +0000 (07:56 +0000)]
kernel: move MTD_SPLIT_SUPPORT to generic config
CONFIG_MTD_SPLIT_SUPPORT symbol default value is 'y' and many platform
specific configs explicitly enables it, while no one platform disables
this symbol. So place it in generic config and remove from platform
specific configs.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44612
John Crispin [Fri, 6 Mar 2015 07:55:57 +0000 (07:55 +0000)]
kernel: remove GENERIC_NET_UTILS from platform configs
CONFIG_GENERIC_NET_UTILS is selected by CONFIG_NET and already enabled
in generic config, so we don't need this symbol in platform specific
configurations.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44611
Luka Perkov [Thu, 5 Mar 2015 23:43:27 +0000 (23:43 +0000)]
kirkwood: drop support for 3.14
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 44610
Luka Perkov [Thu, 5 Mar 2015 23:43:24 +0000 (23:43 +0000)]
kirkwood: switch to 3.18
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 44609
Luka Perkov [Thu, 5 Mar 2015 23:43:21 +0000 (23:43 +0000)]
generic: add CONFIG_FW_LOADER_USER_HELPER symbol
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 44608
John Crispin [Thu, 5 Mar 2015 20:25:18 +0000 (20:25 +0000)]
lantiq: fix netdev setup in ltq-ptm-vdsl
The initial fix for 3.18 in r44346 wrongly treated the newly added
parameter of alloc_netdev to be another function pointer, causing
ether_config to be skipped during ptm netdev init.
Fix this by partially reverting r44346 and properly setting the newly
added macro parameter.
(Tested on VRX200 board)
A similar change might be needed for ltq-ptm-adsl as well.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 44607
John Crispin [Thu, 5 Mar 2015 20:25:11 +0000 (20:25 +0000)]
kernel: add ip_vti tunnel module
IP VTI (Virtual Tunnel Interface) is used to create a virtual device
for IPsec VPN (similar to OpenVPN).
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
SVN-Revision: 44606
John Crispin [Thu, 5 Mar 2015 20:25:02 +0000 (20:25 +0000)]
mtd: fix md5sum error checking
In mtd_verify(), the return value of md5sum() has been
interpreted as error if nonzero, while the function
returns number of processed bytes, which caused
mtd_verify() to always fail.
This patch fixes error checking to interpret only
negative values as errors.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
SVN-Revision: 44605
John Crispin [Thu, 5 Mar 2015 20:24:57 +0000 (20:24 +0000)]
at91: add SAMA5D3-Xplained board UBI parameters to makefile.
Signed-off-by: Songjun Wu <songjun.wu@atmel.com>
SVN-Revision: 44604
John Crispin [Thu, 5 Mar 2015 20:24:50 +0000 (20:24 +0000)]
ath5k: fix reset race
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44603
John Crispin [Thu, 5 Mar 2015 20:24:45 +0000 (20:24 +0000)]
ath5k: channel change fix
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44602
John Crispin [Thu, 5 Mar 2015 20:24:39 +0000 (20:24 +0000)]
brcm2708: add another missing symbol
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 44601
John Crispin [Thu, 5 Mar 2015 20:24:33 +0000 (20:24 +0000)]
generic: add USB_DWC2 missing symbols
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 44600
John Crispin [Thu, 5 Mar 2015 20:24:28 +0000 (20:24 +0000)]
generic: add missing symbols for 4.0
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 44599
John Crispin [Thu, 5 Mar 2015 20:24:22 +0000 (20:24 +0000)]
netfilter: fix nf_nat_redirect dependencies for 3.19 and 4.0
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 44598
Rafał Miłecki [Wed, 4 Mar 2015 07:08:39 +0000 (07:08 +0000)]
kernel: backport bcma changes to 3.19 and 4.0
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 44597
Rafał Miłecki [Tue, 3 Mar 2015 23:15:55 +0000 (23:15 +0000)]
bcm53xx: switch to IRQ buttons (keys)
Now bcma provides IRQ domain we don't have to poll anymore.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 44596
Rafał Miłecki [Tue, 3 Mar 2015 23:15:49 +0000 (23:15 +0000)]
kernel/mac80211: backport bcma changes from 4.1
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 44595
Jonas Gorski [Tue, 3 Mar 2015 14:39:52 +0000 (14:39 +0000)]
generic: upgrade to 3.14.34
Fixes several issues in the network stack.
Full changelog:
* https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.14.33
* https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.14.34
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44594
Jonas Gorski [Tue, 3 Mar 2015 14:39:49 +0000 (14:39 +0000)]
generic: upgrade to 3.18.8
Fixes several issues in the network stack.
Full changelog:
* https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.8
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44593
Felix Fietkau [Mon, 2 Mar 2015 20:33:02 +0000 (20:33 +0000)]
kernel: revert a broken chunk in the mips module reloc patch fix
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 44592
Felix Fietkau [Mon, 2 Mar 2015 04:42:17 +0000 (04:42 +0000)]
kernel: fix the mips module relocation patch for 3.19+
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 44590
Michael Büsch [Sun, 1 Mar 2015 20:44:33 +0000 (20:44 +0000)]
Fix download URL of the 4.x kernel.
SVN-Revision: 44589
projects / openwrt / staging / ldir.git / log