Petr Machata [Thu, 22 Mar 2018 17:53:35 +0000 (19:53 +0200)]
mlxsw: spectrum_router: Handle MTU change of GRE netdevs
Update MTU of overlay loopback in accordance with the setting on the
tunnel netdevice.
Fixes: 0063587d3587 ("mlxsw: spectrum: Support decap-only IP-in-IP tunnels")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 22 Mar 2018 17:53:34 +0000 (19:53 +0200)]
mlxsw: spectrum_router: Move mlxsw_sp_rif_ipip_lb_op()
Move the function so that it can be called without forward declaration
from a function that will be added in a follow-up patch.
Fixes: 0063587d3587 ("mlxsw: spectrum: Support decap-only IP-in-IP tunnels")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 22 Mar 2018 17:53:33 +0000 (19:53 +0200)]
ip_tunnel: Emit events for post-register MTU changes
For tunnels created with IFLA_MTU, MTU of the netdevice is set by
rtnl_create_link() (called from rtnl_newlink()) before the device is
registered. However without IFLA_MTU that's not done.
rtnl_newlink() proceeds by calling struct rtnl_link_ops.newlink, which
via ip_tunnel_newlink() calls register_netdevice(), and that emits
NETDEV_REGISTER. Thus any listeners that inspect the netdevice get the
MTU of 0.
After ip_tunnel_newlink() corrects the MTU after registering the
netdevice, but since there's no event, the listeners don't get to know
about the MTU until something else happens--such as a NETDEV_UP event.
That's not ideal.
So instead of setting the MTU directly, go through dev_set_mtu(), which
takes care of distributing the necessary NETDEV_PRECHANGEMTU and
NETDEV_CHANGEMTU events.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 23 Mar 2018 01:48:43 +0000 (18:48 -0700)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"13 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm, thp: do not cause memcg oom for thp
mm/vmscan: wake up flushers for legacy cgroups too
Revert "mm: page_alloc: skip over regions of invalid pfns where possible"
mm/shmem: do not wait for lock_page() in shmem_unused_huge_shrink()
mm/thp: do not wait for lock_page() in deferred_split_scan()
mm/khugepaged.c: convert VM_BUG_ON() to collapse fail
x86/mm: implement free pmd/pte page interfaces
mm/vmalloc: add interfaces to free unmapped page table
h8300: remove extraneous __BIG_ENDIAN definition
hugetlbfs: check for pgoff value overflow
lockdep: fix fs_reclaim warning
MAINTAINERS: update Mark Fasheh's e-mail
mm/mempolicy.c: avoid use uninitialized preferred_node
Linus Torvalds [Fri, 23 Mar 2018 01:37:49 +0000 (18:37 -0700)]
Merge branch 'libnvdimm-fixes' of git://git./linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"Two regression fixes, two bug fixes for older issues, two fixes for
new functionality added this cycle that have userspace ABI concerns,
and a small cleanup. These have appeared in a linux-next release and
have a build success report from the 0day robot.
* The 4.16 rework of altmap handling led to some configurations
leaking page table allocations due to freeing from the altmap
reservation rather than the page allocator.
The impact without the fix is leaked memory and a WARN() message
when tearing down libnvdimm namespaces. The rework also missed a
place where error handling code needed to be removed that can lead
to a crash if devm_memremap_pages() fails.
* acpi_map_pxm_to_node() had a latent bug whereby it could
misidentify the closest online node to a given proximity domain.
* Block integrity handling was reworked several kernels back to allow
calling add_disk() after setting up the integrity profile.
The nd_btt and nd_blk drivers are just now catching up to fix
automatic partition detection at driver load time.
* The new peristence_domain attribute, a platform indicator of
whether cpu caches are powerfail protected for example, is meant to
be a single value enum and not a set of flags.
This oversight was caught while reviewing new userspace code in
libndctl to communicate the attribute.
Fix this new enabling up so that we are not stuck with an unwanted
userspace ABI"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
libnvdimm, nfit: fix persistence domain reporting
libnvdimm, region: hide persistence_domain when unknown
acpi, numa: fix pxm to online numa node associations
x86, memremap: fix altmap accounting at free
libnvdimm: remove redundant assignment to pointer 'dev'
libnvdimm, {btt, blk}: do integrity setup before add_disk()
kernel/memremap: Remove stale devres_free() call
Linus Torvalds [Fri, 23 Mar 2018 00:37:44 +0000 (17:37 -0700)]
Merge tag 'drm-fixes-for-v4.16-rc7' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"A bunch of fixes all over the place (core, i915, amdgpu, imx, sun4i,
ast, tegra, vmwgfx), nothing too serious or worrying at this stage.
- one uapi fix to stop multi-planar images with getfb
- Sun4i error path and clock fixes
- udl driver mmap offset fix
- i915 DP MST and GPU reset fixes
- vmwgfx mutex and black screen fixes
- imx array underflow fix and vblank fix
- amdgpu: display fixes
- exynos devicetree fix
- ast mode fix"
* tag 'drm-fixes-for-v4.16-rc7' of git://people.freedesktop.org/~airlied/linux: (29 commits)
drm/ast: Fixed 1280x800 Display Issue
drm: udl: Properly check framebuffer mmap offsets
drm/i915: Specify which engines to reset following semaphore/event lockups
drm/vmwgfx: Fix a destoy-while-held mutex problem.
drm/vmwgfx: Fix black screen and device errors when running without fbdev
drm: Reject getfb for multi-plane framebuffers
drm/amd/display: Add one to EDID's audio channel count when passing to DC
drm/amd/display: We shouldn't set format_default on plane as atomic driver
drm/amd/display: Fix FMT truncation programming
drm/amd/display: Allow truncation to 10 bits
drm/sun4i: hdmi: Fix another error handling path in 'sun4i_hdmi_bind()'
drm/sun4i: hdmi: Fix an error handling path in 'sun4i_hdmi_bind()'
drm/i915/dp: Write to SET_POWER dpcd to enable MST hub.
drm/amd/display: fix dereferencing possible ERR_PTR()
drm/amd/display: Refine disable VGA
drm/tegra: Shutdown on driver unbind
drm/tegra: dsi: Don't disable regulator on ->exit()
drm/tegra: dc: Detach IOMMU group from domain only once
dt-bindings: exynos: Document #sound-dai-cells property of the HDMI node
drm/imx: move arming of the vblank event to atomic_flush
...
David Rientjes [Thu, 22 Mar 2018 23:17:45 +0000 (16:17 -0700)]
mm, thp: do not cause memcg oom for thp
Commit
2516035499b9 ("mm, thp: remove __GFP_NORETRY from khugepaged and
madvised allocations") changed the page allocator to no longer detect
thp allocations based on __GFP_NORETRY.
It did not, however, modify the mem cgroup try_charge() path to avoid
oom kill for either khugepaged collapsing or thp faulting. It is never
expected to oom kill a process to allocate a hugepage for thp; reclaim
is governed by the thp defrag mode and MADV_HUGEPAGE, but allocations
(and charging) should fallback instead of oom killing processes.
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1803191409420.124411@chino.kir.corp.google.com
Fixes: 2516035499b9 ("mm, thp: remove __GFP_NORETRY from khugepaged and madvised allocations")
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Ryabinin [Thu, 22 Mar 2018 23:17:42 +0000 (16:17 -0700)]
mm/vmscan: wake up flushers for legacy cgroups too
Commit
726d061fbd36 ("mm: vmscan: kick flushers when we encounter dirty
pages on the LRU") added flusher invocation to shrink_inactive_list()
when many dirty pages on the LRU are encountered.
However, shrink_inactive_list() doesn't wake up flushers for legacy
cgroup reclaim, so the next commit
bbef938429f5 ("mm: vmscan: remove old
flusher wakeup from direct reclaim path") removed the only source of
flusher's wake up in legacy mem cgroup reclaim path.
This leads to premature OOM if there is too many dirty pages in cgroup:
# mkdir /sys/fs/cgroup/memory/test
# echo $$ > /sys/fs/cgroup/memory/test/tasks
# echo 50M > /sys/fs/cgroup/memory/test/memory.limit_in_bytes
# dd if=/dev/zero of=tmp_file bs=1M count=100
Killed
dd invoked oom-killer: gfp_mask=0x14000c0(GFP_KERNEL), nodemask=(null), order=0, oom_score_adj=0
Call Trace:
dump_stack+0x46/0x65
dump_header+0x6b/0x2ac
oom_kill_process+0x21c/0x4a0
out_of_memory+0x2a5/0x4b0
mem_cgroup_out_of_memory+0x3b/0x60
mem_cgroup_oom_synchronize+0x2ed/0x330
pagefault_out_of_memory+0x24/0x54
__do_page_fault+0x521/0x540
page_fault+0x45/0x50
Task in /test killed as a result of limit of /test
memory: usage 51200kB, limit 51200kB, failcnt 73
memory+swap: usage 51200kB, limit 9007199254740988kB, failcnt 0
kmem: usage 296kB, limit 9007199254740988kB, failcnt 0
Memory cgroup stats for /test: cache:49632KB rss:1056KB rss_huge:0KB shmem:0KB
mapped_file:0KB dirty:49500KB writeback:0KB swap:0KB inactive_anon:0KB
active_anon:1168KB inactive_file:24760KB active_file:24960KB unevictable:0KB
Memory cgroup out of memory: Kill process 3861 (bash) score 88 or sacrifice child
Killed process 3876 (dd) total-vm:8484kB, anon-rss:1052kB, file-rss:1720kB, shmem-rss:0kB
oom_reaper: reaped process 3876 (dd), now anon-rss:0kB, file-rss:0kB, shmem-rss:0kB
Wake up flushers in legacy cgroup reclaim too.
Link: http://lkml.kernel.org/r/20180315164553.17856-1-aryabinin@virtuozzo.com
Fixes: bbef938429f5 ("mm: vmscan: remove old flusher wakeup from direct reclaim path")
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Tested-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Tejun Heo <tj@kernel.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Daniel Vacek [Thu, 22 Mar 2018 23:17:38 +0000 (16:17 -0700)]
Revert "mm: page_alloc: skip over regions of invalid pfns where possible"
This reverts commit
b92df1de5d28 ("mm: page_alloc: skip over regions of
invalid pfns where possible"). The commit is meant to be a boot init
speed up skipping the loop in memmap_init_zone() for invalid pfns.
But given some specific memory mapping on x86_64 (or more generally
theoretically anywhere but on arm with CONFIG_HAVE_ARCH_PFN_VALID) the
implementation also skips valid pfns which is plain wrong and causes
'kernel BUG at mm/page_alloc.c:1389!'
crash> log | grep -e BUG -e RIP -e Call.Trace -e move_freepages_block -e rmqueue -e freelist -A1
kernel BUG at mm/page_alloc.c:1389!
invalid opcode: 0000 [#1] SMP
--
RIP: 0010: move_freepages+0x15e/0x160
--
Call Trace:
move_freepages_block+0x73/0x80
__rmqueue+0x263/0x460
get_page_from_freelist+0x7e1/0x9e0
__alloc_pages_nodemask+0x176/0x420
--
crash> page_init_bug -v | grep RAM
<struct resource 0xffff88067fffd2f8> 1000 - 9bfff System RAM (620.00 KiB)
<struct resource 0xffff88067fffd3a0> 100000 -
430bffff System RAM ( 1.05 GiB = 1071.75 MiB =
1097472.00 KiB)
<struct resource 0xffff88067fffd410>
4b0c8000 -
4bf9cfff System RAM ( 14.83 MiB = 15188.00 KiB)
<struct resource 0xffff88067fffd480>
4bfac000 -
646b1fff System RAM (391.02 MiB = 400408.00 KiB)
<struct resource 0xffff88067fffd560>
7b788000 -
7b7fffff System RAM (480.00 KiB)
<struct resource 0xffff88067fffd640>
100000000 -
67fffffff System RAM ( 22.00 GiB)
crash> page_init_bug | head -6
<struct resource 0xffff88067fffd560>
7b788000 -
7b7fffff System RAM (480.00 KiB)
<struct page 0xffffea0001ede200>
1fffff00000000 0 <struct pglist_data 0xffff88047ffd9000> 1 <struct zone 0xffff88047ffd9800> DMA32 4096
1048575
<struct page 0xffffea0001ede200> 505736 505344 <struct page 0xffffea0001ed8000> 505855 <struct page 0xffffea0001edffc0>
<struct page 0xffffea0001ed8000> 0 0 <struct pglist_data 0xffff88047ffd9000> 0 <struct zone 0xffff88047ffd9000> DMA 1 4095
<struct page 0xffffea0001edffc0>
1fffff00000400 0 <struct pglist_data 0xffff88047ffd9000> 1 <struct zone 0xffff88047ffd9800> DMA32 4096
1048575
BUG, zones differ!
crash> kmem -p
77fff000 78000000 7b5ff000 7b600000 7b787000 7b788000
PAGE PHYSICAL MAPPING INDEX CNT FLAGS
ffffea0001e00000 78000000 0 0 0 0
ffffea0001ed7fc0 7b5ff000 0 0 0 0
ffffea0001ed8000 7b600000 0 0 0 0 <<<<
ffffea0001ede1c0 7b787000 0 0 0 0
ffffea0001ede200 7b788000 0 0 1
1fffff00000000
Link: http://lkml.kernel.org/r/20180316143855.29838-1-neelx@redhat.com
Fixes: b92df1de5d28 ("mm: page_alloc: skip over regions of invalid pfns where possible")
Signed-off-by: Daniel Vacek <neelx@redhat.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Pavel Tatashin <pasha.tatashin@oracle.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kirill A. Shutemov [Thu, 22 Mar 2018 23:17:35 +0000 (16:17 -0700)]
mm/shmem: do not wait for lock_page() in shmem_unused_huge_shrink()
shmem_unused_huge_shrink() gets called from reclaim path. Waiting for
page lock may lead to deadlock there.
There was a bug report that may be attributed to this:
http://lkml.kernel.org/r/alpine.LRH.2.11.
1801242349220.30642@mail.ewheeler.net
Replace lock_page() with trylock_page() and skip the page if we failed
to lock it. We will get to the page on the next scan.
We can test for the PageTransHuge() outside the page lock as we only
need protection against splitting the page under us. Holding pin oni
the page is enough for this.
Link: http://lkml.kernel.org/r/20180316210830.43738-1-kirill.shutemov@linux.intel.com
Fixes: 779750d20b93 ("shmem: split huge pages beyond i_size under memory pressure")
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: Eric Wheeler <linux-mm@lists.ewheeler.net>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Hugh Dickins <hughd@google.com>
Cc: <stable@vger.kernel.org> [4.8+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kirill A. Shutemov [Thu, 22 Mar 2018 23:17:31 +0000 (16:17 -0700)]
mm/thp: do not wait for lock_page() in deferred_split_scan()
deferred_split_scan() gets called from reclaim path. Waiting for page
lock may lead to deadlock there.
Replace lock_page() with trylock_page() and skip the page if we failed
to lock it. We will get to the page on the next scan.
Link: http://lkml.kernel.org/r/20180315150747.31945-1-kirill.shutemov@linux.intel.com
Fixes: 9a982250f773 ("thp: introduce deferred_split_huge_page()")
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kirill A. Shutemov [Thu, 22 Mar 2018 23:17:28 +0000 (16:17 -0700)]
mm/khugepaged.c: convert VM_BUG_ON() to collapse fail
khugepaged is not yet able to convert PTE-mapped huge pages back to PMD
mapped. We do not collapse such pages. See check
khugepaged_scan_pmd().
But if between khugepaged_scan_pmd() and __collapse_huge_page_isolate()
somebody managed to instantiate THP in the range and then split the PMD
back to PTEs we would have a problem --
VM_BUG_ON_PAGE(PageCompound(page)) will get triggered.
It's possible since we drop mmap_sem during collapse to re-take for
write.
Replace the VM_BUG_ON() with graceful collapse fail.
Link: http://lkml.kernel.org/r/20180315152353.27989-1-kirill.shutemov@linux.intel.com
Fixes: b1caa957ae6d ("khugepaged: ignore pmd tables with THP mapped with ptes")
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Toshi Kani [Thu, 22 Mar 2018 23:17:24 +0000 (16:17 -0700)]
x86/mm: implement free pmd/pte page interfaces
Implement pud_free_pmd_page() and pmd_free_pte_page() on x86, which
clear a given pud/pmd entry and free up lower level page table(s).
The address range associated with the pud/pmd entry must have been
purged by INVLPG.
Link: http://lkml.kernel.org/r/20180314180155.19492-3-toshi.kani@hpe.com
Fixes: e61ce6ade404e ("mm: change ioremap to set up huge I/O mappings")
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Reported-by: Lei Li <lious.lilei@hisilicon.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Toshi Kani [Thu, 22 Mar 2018 23:17:20 +0000 (16:17 -0700)]
mm/vmalloc: add interfaces to free unmapped page table
On architectures with CONFIG_HAVE_ARCH_HUGE_VMAP set, ioremap() may
create pud/pmd mappings. A kernel panic was observed on arm64 systems
with Cortex-A75 in the following steps as described by Hanjun Guo.
1. ioremap a 4K size, valid page table will build,
2. iounmap it, pte0 will set to 0;
3. ioremap the same address with 2M size, pgd/pmd is unchanged,
then set the a new value for pmd;
4. pte0 is leaked;
5. CPU may meet exception because the old pmd is still in TLB,
which will lead to kernel panic.
This panic is not reproducible on x86. INVLPG, called from iounmap,
purges all levels of entries associated with purged address on x86. x86
still has memory leak.
The patch changes the ioremap path to free unmapped page table(s) since
doing so in the unmap path has the following issues:
- The iounmap() path is shared with vunmap(). Since vmap() only
supports pte mappings, making vunmap() to free a pte page is an
overhead for regular vmap users as they do not need a pte page freed
up.
- Checking if all entries in a pte page are cleared in the unmap path
is racy, and serializing this check is expensive.
- The unmap path calls free_vmap_area_noflush() to do lazy TLB purges.
Clearing a pud/pmd entry before the lazy TLB purges needs extra TLB
purge.
Add two interfaces, pud_free_pmd_page() and pmd_free_pte_page(), which
clear a given pud/pmd entry and free up a page for the lower level
entries.
This patch implements their stub functions on x86 and arm64, which work
as workaround.
[akpm@linux-foundation.org: fix typo in pmd_free_pte_page() stub]
Link: http://lkml.kernel.org/r/20180314180155.19492-2-toshi.kani@hpe.com
Fixes: e61ce6ade404e ("mm: change ioremap to set up huge I/O mappings")
Reported-by: Lei Li <lious.lilei@hisilicon.com>
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Wang Xuefeng <wxf.wang@hisilicon.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Hanjun Guo <guohanjun@huawei.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Chintan Pandya <cpandya@codeaurora.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arnd Bergmann [Thu, 22 Mar 2018 23:17:17 +0000 (16:17 -0700)]
h8300: remove extraneous __BIG_ENDIAN definition
A bugfix I did earlier caused a build regression on h8300, which defines
the __BIG_ENDIAN macro in a slightly different way than the generic
code:
arch/h8300/include/asm/byteorder.h:5:0: warning: "__BIG_ENDIAN" redefined
We don't need to define it here, as the same macro is already provided
by the linux/byteorder/big_endian.h, and that version does not conflict.
While this is a v4.16 regression, my earlier patch also got backported
to the 4.14 and 4.15 stable kernels, so we need the fixup there as well.
Link: http://lkml.kernel.org/r/20180313120752.2645129-1-arnd@arndb.de
Fixes: 101110f6271c ("Kbuild: always define endianess in kconfig.h")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Kravetz [Thu, 22 Mar 2018 23:17:13 +0000 (16:17 -0700)]
hugetlbfs: check for pgoff value overflow
A vma with vm_pgoff large enough to overflow a loff_t type when
converted to a byte offset can be passed via the remap_file_pages system
call. The hugetlbfs mmap routine uses the byte offset to calculate
reservations and file size.
A sequence such as:
mmap(0x20a00000, 0x600000, 0, 0x66033, -1, 0);
remap_file_pages(0x20a00000, 0x600000, 0, 0x20000000000000, 0);
will result in the following when task exits/file closed,
kernel BUG at mm/hugetlb.c:749!
Call Trace:
hugetlbfs_evict_inode+0x2f/0x40
evict+0xcb/0x190
__dentry_kill+0xcb/0x150
__fput+0x164/0x1e0
task_work_run+0x84/0xa0
exit_to_usermode_loop+0x7d/0x80
do_syscall_64+0x18b/0x190
entry_SYSCALL_64_after_hwframe+0x3d/0xa2
The overflowed pgoff value causes hugetlbfs to try to set up a mapping
with a negative range (end < start) that leaves invalid state which
causes the BUG.
The previous overflow fix to this code was incomplete and did not take
the remap_file_pages system call into account.
[mike.kravetz@oracle.com: v3]
Link: http://lkml.kernel.org/r/20180309002726.7248-1-mike.kravetz@oracle.com
[akpm@linux-foundation.org: include mmdebug.h]
[akpm@linux-foundation.org: fix -ve left shift count on sh]
Link: http://lkml.kernel.org/r/20180308210502.15952-1-mike.kravetz@oracle.com
Fixes: 045c7a3f53d9 ("hugetlbfs: fix offset overflow in hugetlbfs mmap")
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Reported-by: Nic Losby <blurbdust@gmail.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Yisheng Xie <xieyisheng1@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tetsuo Handa [Thu, 22 Mar 2018 23:17:10 +0000 (16:17 -0700)]
lockdep: fix fs_reclaim warning
Dave Jones reported fs_reclaim lockdep warnings.
============================================
WARNING: possible recursive locking detected
4.15.0-rc9-backup-debug+ #1 Not tainted
--------------------------------------------
sshd/24800 is trying to acquire lock:
(fs_reclaim){+.+.}, at: [<
0000000084f438c2>] fs_reclaim_acquire.part.102+0x5/0x30
but task is already holding lock:
(fs_reclaim){+.+.}, at: [<
0000000084f438c2>] fs_reclaim_acquire.part.102+0x5/0x30
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(fs_reclaim);
lock(fs_reclaim);
*** DEADLOCK ***
May be due to missing lock nesting notation
2 locks held by sshd/24800:
#0: (sk_lock-AF_INET6){+.+.}, at: [<
000000001a069652>] tcp_sendmsg+0x19/0x40
#1: (fs_reclaim){+.+.}, at: [<
0000000084f438c2>] fs_reclaim_acquire.part.102+0x5/0x30
stack backtrace:
CPU: 3 PID: 24800 Comm: sshd Not tainted 4.15.0-rc9-backup-debug+ #1
Call Trace:
dump_stack+0xbc/0x13f
__lock_acquire+0xa09/0x2040
lock_acquire+0x12e/0x350
fs_reclaim_acquire.part.102+0x29/0x30
kmem_cache_alloc+0x3d/0x2c0
alloc_extent_state+0xa7/0x410
__clear_extent_bit+0x3ea/0x570
try_release_extent_mapping+0x21a/0x260
__btrfs_releasepage+0xb0/0x1c0
btrfs_releasepage+0x161/0x170
try_to_release_page+0x162/0x1c0
shrink_page_list+0x1d5a/0x2fb0
shrink_inactive_list+0x451/0x940
shrink_node_memcg.constprop.88+0x4c9/0x5e0
shrink_node+0x12d/0x260
try_to_free_pages+0x418/0xaf0
__alloc_pages_slowpath+0x976/0x1790
__alloc_pages_nodemask+0x52c/0x5c0
new_slab+0x374/0x3f0
___slab_alloc.constprop.81+0x47e/0x5a0
__slab_alloc.constprop.80+0x32/0x60
__kmalloc_track_caller+0x267/0x310
__kmalloc_reserve.isra.40+0x29/0x80
__alloc_skb+0xee/0x390
sk_stream_alloc_skb+0xb8/0x340
tcp_sendmsg_locked+0x8e6/0x1d30
tcp_sendmsg+0x27/0x40
inet_sendmsg+0xd0/0x310
sock_write_iter+0x17a/0x240
__vfs_write+0x2ab/0x380
vfs_write+0xfb/0x260
SyS_write+0xb6/0x140
do_syscall_64+0x1e5/0xc05
entry_SYSCALL64_slow_path+0x25/0x25
This warning is caused by commit
d92a8cfcb37e ("locking/lockdep:
Rework FS_RECLAIM annotation") which replaced the use of
lockdep_{set,clear}_current_reclaim_state() in __perform_reclaim()
and lockdep_trace_alloc() in slab_pre_alloc_hook() with
fs_reclaim_acquire()/ fs_reclaim_release().
Since __kmalloc_reserve() from __alloc_skb() adds __GFP_NOMEMALLOC |
__GFP_NOWARN to gfp_mask, and all reclaim path simply propagates
__GFP_NOMEMALLOC, fs_reclaim_acquire() in slab_pre_alloc_hook() is
trying to grab the 'fake' lock again when __perform_reclaim() already
grabbed the 'fake' lock.
The
/* this guy won't enter reclaim */
if ((current->flags & PF_MEMALLOC) && !(gfp_mask & __GFP_NOMEMALLOC))
return false;
test which causes slab_pre_alloc_hook() to try to grab the 'fake' lock
was added by commit
cf40bd16fdad ("lockdep: annotate reclaim context
(__GFP_NOFS)"). But that test is outdated because PF_MEMALLOC thread
won't enter reclaim regardless of __GFP_NOMEMALLOC after commit
341ce06f69ab ("page allocator: calculate the alloc_flags for allocation
only once") added the PF_MEMALLOC safeguard (
/* Avoid recursion of direct reclaim */
if (p->flags & PF_MEMALLOC)
goto nopage;
in __alloc_pages_slowpath()).
Thus, let's fix outdated test by removing __GFP_NOMEMALLOC test and
allow __need_fs_reclaim() to return false.
Link: http://lkml.kernel.org/r/201802280650.FJC73911.FOSOMLJVFFQtHO@I-love.SAKURA.ne.jp
Fixes: d92a8cfcb37ecd13 ("locking/lockdep: Rework FS_RECLAIM annotation")
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Tested-by: Dave Jones <davej@codemonkey.org.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Nick Piggin <npiggin@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Nikolay Borisov <nborisov@suse.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: <stable@vger.kernel.org> [4.14+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mark Fasheh [Thu, 22 Mar 2018 23:17:05 +0000 (16:17 -0700)]
MAINTAINERS: update Mark Fasheh's e-mail
I'd like to use my personal e-mail for Ocfs2 requests and review.
Link: http://lkml.kernel.org/r/20180311231356.9385-1-mfasheh@versity.com
Signed-off-by: Mark Fasheh <mark@fasheh.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Yisheng Xie [Thu, 22 Mar 2018 23:17:02 +0000 (16:17 -0700)]
mm/mempolicy.c: avoid use uninitialized preferred_node
Alexander reported a use of uninitialized memory in __mpol_equal(),
which is caused by incorrect use of preferred_node.
When mempolicy in mode MPOL_PREFERRED with flags MPOL_F_LOCAL, it uses
numa_node_id() instead of preferred_node, however, __mpol_equal() uses
preferred_node without checking whether it is MPOL_F_LOCAL or not.
[akpm@linux-foundation.org: slight comment tweak]
Link: http://lkml.kernel.org/r/4ebee1c2-57f6-bcb8-0e2d-1833d1ee0bb7@huawei.com
Fixes: fc36b8d3d819 ("mempolicy: use MPOL_F_LOCAL to Indicate Preferred Local Policy")
Signed-off-by: Yisheng Xie <xieyisheng1@huawei.com>
Reported-by: Alexander Potapenko <glider@google.com>
Tested-by: Alexander Potapenko <glider@google.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Dmitriy Vyukov <dvyukov@google.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Michal Hocko <mhocko@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Y.C. Chen [Mon, 12 Mar 2018 03:40:23 +0000 (11:40 +0800)]
drm/ast: Fixed 1280x800 Display Issue
The original ast driver cannot display properly if the resolution is 1280x800 and the pixel clock is 83.5MHz.
Here is the update to fix it.
Signed-off-by: Y.C. Chen <yc_chen@aspeedtech.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Linus Torvalds [Thu, 22 Mar 2018 23:20:25 +0000 (16:20 -0700)]
Merge tag 'acpi-4.16-rc7' of git://git./linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These revert one recent commit that added incorrect battery quirks for
some Asus systems and fix an off-by-one error in the watchdog driver
based on the ACPI WDAT table.
Specifics:
- Revert the recent change adding battery quirks for Asus GL502VSK
and UX305LA as these quirks turn out to be inadequate and possibly
premature (Daniel Drake).
- Fix an off-by-one error in the resource allocation part of the
watchdog driver based on the ACPI WDAT table (Takashi Iwai)"
* tag 'acpi-4.16-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / watchdog: Fix off-by-one error at resource assignment
Revert "ACPI / battery: Add quirk for Asus GL502VSK and UX305LA"
Linus Torvalds [Thu, 22 Mar 2018 23:13:49 +0000 (16:13 -0700)]
Merge tag 'modules-for-v4.16-rc7' of git://git./linux/kernel/git/jeyu/linux
Pull modules fix from Jessica Yu:
"Propagate error in modules_open() to avoid possible later NULL
dereference if seq_open() had failed"
* tag 'modules-for-v4.16-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
module: propagate error in modules_open()
Rafael J. Wysocki [Thu, 22 Mar 2018 22:42:08 +0000 (23:42 +0100)]
Merge branch 'acpi-wdat'
* acpi-wdat:
ACPI / watchdog: Fix off-by-one error at resource assignment
Linus Torvalds [Thu, 22 Mar 2018 21:10:29 +0000 (14:10 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Always validate XFRM esn replay attribute, from Florian Westphal.
2) Fix RCU read lock imbalance in xfrm_get_tos(), from Xin Long.
3) Don't try to get firmware dump if not loaded in iwlwifi, from Shaul
Triebitz.
4) Fix BPF helpers to deal with SCTP GSO SKBs properly, from Daniel
Axtens.
5) Fix some interrupt handling issues in e1000e driver, from Benjamin
Poitier.
6) Use strlcpy() in several ethtool get_strings methods, from Florian
Fainelli.
7) Fix rhlist dup insertion, from Paul Blakey.
8) Fix SKB leak in netem packet scheduler, from Alexey Kodanev.
9) Fix driver unload crash when link is up in smsc911x, from Jeremy
Linton.
10) Purge out invalid socket types in l2tp_tunnel_create(), from Eric
Dumazet.
11) Need to purge the write queue when TCP connections are aborted,
otherwise userspace using MSG_ZEROCOPY can't close the fd. From
Soheil Hassas Yeganeh.
12) Fix double free in error path of team driver, from Arkadi
Sharshevsky.
13) Filter fixes for hv_netvsc driver, from Stephen Hemminger.
14) Fix non-linear packet access in ipv6 ndisc code, from Lorenzo
Bianconi.
15) Properly filter out unsupported feature flags in macvlan driver,
from Shannon Nelson.
16) Don't request loading the diag module for a protocol if the protocol
itself is not even registered. From Xin Long.
17) If datagram connect fails in ipv6, make sure the socket state is
consistent afterwards. From Paolo Abeni.
18) Use after free in qed driver, from Dan Carpenter.
19) If received ipv4 PMTU is less than the min pmtu, lock the mtu in the
entry. From Sabrina Dubroca.
20) Fix sleep in atomic in tg3 driver, from Jonathan Toppins.
21) Fix vlan in vlan untagging in some situations, from Toshiaki Makita.
22) Fix double SKB free in genlmsg_mcast(). From Nicolas Dichtel.
23) Fix NULL derefs in error paths of tcf_*_init(), from Davide Caratti.
24) Unbalanced PM runtime calls in FEC driver, from Florian Fainelli.
25) Memory leak in gemini driver, from Igor Pylypiv.
26) IDR leaks in error paths of tcf_*_init() functions, from Davide
Caratti.
27) Need to use GFP_ATOMIC in seg6_build_state(), from David Lebrun.
28) Missing dev_put() in error path of macsec_newlink(), from Dan
Carpenter.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (201 commits)
macsec: missing dev_put() on error in macsec_newlink()
net: dsa: Fix functional dsa-loop dependency on FIXED_PHY
hv_netvsc: common detach logic
hv_netvsc: change GPAD teardown order on older versions
hv_netvsc: use RCU to fix concurrent rx and queue changes
hv_netvsc: disable NAPI before channel close
net/ipv6: Handle onlink flag with multipath routes
ppp: avoid loop in xmit recursion detection code
ipv6: sr: fix NULL pointer dereference when setting encap source address
ipv6: sr: fix scheduling in RCU when creating seg6 lwtunnel state
net: aquantia: driver version bump
net: aquantia: Implement pci shutdown callback
net: aquantia: Allow live mac address changes
net: aquantia: Add tx clean budget and valid budget handling logic
net: aquantia: Change inefficient wait loop on fw data reads
net: aquantia: Fix a regression with reset on old firmware
net: aquantia: Fix hardware reset when SPI may rarely hangup
s390/qeth: on channel error, reject further cmd requests
s390/qeth: lock read device while queueing next buffer
s390/qeth: when thread completes, wake up all waiters
...
Linus Torvalds [Thu, 22 Mar 2018 20:29:55 +0000 (13:29 -0700)]
Merge tag 'mmc-v4.16-rc4' of git://git./linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"A couple of MMC fixes intended for v4.16-rc7:
MMC host:
- dw_mmc: Fix the suspend/resume issue for Exynos5433
- dw_mmc: Fix the DTO/CTO timeout overflow calculation for 32-bit
systems
- dw_mmc: Make PIO mode work when failing with idmac when
dw_mci_reset occurs
- sdhci-acpi: Re-allow IRQ 0 to fix broken probe
MMC core:
- Update EXT_CSD caches to correctly switch partition for ioctl calls
- Fix tracepoint print of blk_addr and blksz
- Disable HPI on broken Micron (Numonyx) eMMC cards"
* tag 'mmc-v4.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci-acpi: Fix IRQ 0
mmc: dw_mmc: fix falling from idmac to PIO mode when dw_mci_reset occurs
mmc: core: Fix tracepoint print of blk_addr and blksz
mmc: core: Disable HPI for certain Micron (Numonyx) eMMC cards
mmc: dw_mmc: exynos: fix the suspend/resume issue for exynos5433
mmc: block: fix updating ext_csd caches on ioctl call
mmc: dw_mmc: Fix the DTO/CTO timeout overflow calculation for 32-bit systems
Dave Airlie [Thu, 22 Mar 2018 20:19:56 +0000 (06:19 +1000)]
Merge tag 'drm-misc-fixes-2018-03-22' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Main change is a patch to reject getfb call for multiplanar framebuffers,
then we have a couple of error path fixes on the sun4i driver. Still on that
driver there is a clk fix and finally a mmap offset fix on the udl driver.
* tag 'drm-misc-fixes-2018-03-22' of git://anongit.freedesktop.org/drm/drm-misc:
drm: udl: Properly check framebuffer mmap offsets
drm: Reject getfb for multi-plane framebuffers
drm/sun4i: hdmi: Fix another error handling path in 'sun4i_hdmi_bind()'
drm/sun4i: hdmi: Fix an error handling path in 'sun4i_hdmi_bind()'
drm/sun4i: Fix an error handling path in 'sun4i_drv_bind()'
drm/sun4i: Fix exclusivity of the TCON clocks
Dave Airlie [Thu, 22 Mar 2018 20:15:44 +0000 (06:15 +1000)]
Merge tag 'drm-intel-fixes-2018-03-21' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
One fix for DP MST and one fix for GPU reset on hang check.
* tag 'drm-intel-fixes-2018-03-21' of git://anongit.freedesktop.org/drm/drm-intel:
drm/i915: Specify which engines to reset following semaphore/event lockups
drm/i915/dp: Write to SET_POWER dpcd to enable MST hub.
Dave Airlie [Thu, 22 Mar 2018 20:15:08 +0000 (06:15 +1000)]
Merge branch 'vmwgfx-fixes-4.16' of git://people.freedesktop.org/~thomash/linux into drm-fixes
Two vmwgfx fixes for 4.16. Both cc'd stable.
* 'vmwgfx-fixes-4.16' of git://people.freedesktop.org/~thomash/linux:
drm/vmwgfx: Fix a destoy-while-held mutex problem.
drm/vmwgfx: Fix black screen and device errors when running without fbdev
Dave Airlie [Thu, 22 Mar 2018 20:14:15 +0000 (06:14 +1000)]
Merge tag 'imx-drm-fixes-2018-03-22' of git://git.pengutronix.de/git/pza/linux into drm-fixes
drm/imx: fixes for early vblank event issue, array underflow error
- fix an array underflow error by reordering the range check before the array
subscript in ipu-prg.
- make some local functions static in ipuv3-plane.
- add a missng header for ipu_planes_assign_pre in ipuv3-plane.
- move arming of the vblank event from atomic_begin to atomic_flush, to avoid
signalling atomic commit completion to userspace before plane atomic_update
has finished, due to a race condition that is likely to be hit on i.MX6QP on
PRE enabled channels.
* tag 'imx-drm-fixes-2018-03-22' of git://git.pengutronix.de/git/pza/linux:
drm/imx: move arming of the vblank event to atomic_flush
drm/imx: ipuv3-plane: Include "imx-drm.h" header file
drm/imx: ipuv3-plane: Make functions static when possible
gpu: ipu-v3: prg: avoid possible array underflow
Dan Carpenter [Wed, 21 Mar 2018 08:09:01 +0000 (11:09 +0300)]
macsec: missing dev_put() on error in macsec_newlink()
We moved the dev_hold(real_dev); call earlier in the function but forgot
to update the error paths.
Fixes: 0759e552bce7 ("macsec: fix negative refcnt on parent link")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 22 Mar 2018 17:19:10 +0000 (13:19 -0400)]
Merge tag 'mac80211-for-davem-2018-03-21' of git://git./linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Two more fixes (in three patches):
* ath9k_htc doesn't like QoS NDP frames, use regular ones
* hwsim: set up wmediumd for radios created later
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 21 Mar 2018 00:31:10 +0000 (17:31 -0700)]
net: dsa: Fix functional dsa-loop dependency on FIXED_PHY
We have a functional dependency on the FIXED_PHY MDIO bus because we register
fixed PHY devices "the old way" which only works if the code that does this has
had a chance to run before the fixed MDIO bus is probed. Make sure we account
for that and have dsa_loop_bdinfo.o be either built-in or modular depending on
whether CONFIG_FIXED_PHY reflects that too.
Fixes: 98cd1552ea27 ("net: dsa: Mock-up driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 22 Mar 2018 16:45:10 +0000 (12:45 -0400)]
Merge branch 'hv_netvsc-fix-races-during-shutdown-and-changes'
Stephen Hemminger says:
====================
hv_netvsc: fix races during shutdown and changes
This set of patches fixes issues identified by Vitaly Kuznetsov and
Mohammed Gamal related to state changes in Hyper-v network driver.
A lot of the issues are because setting up the netvsc device requires
a second step (in work queue) to get all the sub-channels running.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Tue, 20 Mar 2018 22:03:05 +0000 (15:03 -0700)]
hv_netvsc: common detach logic
Make common function for detaching internals of device
during changes to MTU and RSS. Make sure no more packets
are transmitted and all packets have been received before
doing device teardown.
Change the wait logic to be common and use usleep_range().
Changes transmit enabling logic so that transmit queues are disabled
during the period when lower device is being changed. And enabled
only after sub channels are setup. This avoids issue where it could
be that a packet was being sent while subchannel was not initialized.
Fixes: 8195b1396ec8 ("hv_netvsc: fix deadlock on hotplug")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Tue, 20 Mar 2018 22:03:04 +0000 (15:03 -0700)]
hv_netvsc: change GPAD teardown order on older versions
On older versions of Windows, the host ignores messages after
vmbus channel is closed.
Workaround this by doing what Windows does and send the teardown
before close on older versions of NVSP protocol.
Reported-by: Mohammed Gamal <mgamal@redhat.com>
Fixes: 0cf737808ae7 ("hv_netvsc: netvsc_teardown_gpadl() split")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Tue, 20 Mar 2018 22:03:03 +0000 (15:03 -0700)]
hv_netvsc: use RCU to fix concurrent rx and queue changes
The receive processing may continue to happen while the
internal network device state is in RCU grace period.
The internal RNDIS structure is associated with the
internal netvsc_device structure; both have the same
RCU lifetime.
Defer freeing all associated parts until after grace
period.
Fixes: 0cf737808ae7 ("hv_netvsc: netvsc_teardown_gpadl() split")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Tue, 20 Mar 2018 22:03:02 +0000 (15:03 -0700)]
hv_netvsc: disable NAPI before channel close
This makes sure that no CPU is still process packets when
the channel is closed.
Fixes: 76bb5db5c749 ("netvsc: fix use after free on module removal")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 20 Mar 2018 17:06:59 +0000 (10:06 -0700)]
net/ipv6: Handle onlink flag with multipath routes
For multipath routes the ONLINK flag can be specified per nexthop in
rtnh_flags or globally in rtm_flags. Update ip6_route_multipath_add
to consider the ONLINK setting coming from rtnh_flags. Each loop over
nexthops the config for the sibling route is initialized to the global
config and then per nexthop settings overlayed. The flag is 'or'ed into
fib6_config to handle the ONLINK flag coming from either rtm_flags or
rtnh_flags.
Fixes: fc1e64e1092f ("net/ipv6: Add support for onlink flag")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault [Tue, 20 Mar 2018 15:49:26 +0000 (16:49 +0100)]
ppp: avoid loop in xmit recursion detection code
We already detect situations where a PPP channel sends packets back to
its upper PPP device. While this is enough to avoid deadlocking on xmit
locks, this doesn't prevent packets from looping between the channel
and the unit.
The problem is that ppp_start_xmit() enqueues packets in ppp->file.xq
before checking for xmit recursion. Therefore, __ppp_xmit_process()
might dequeue a packet from ppp->file.xq and send it on the channel
which, in turn, loops it back on the unit. Then ppp_start_xmit()
queues the packet back to ppp->file.xq and __ppp_xmit_process() picks
it up and sends it again through the channel. Therefore, the packet
will loop between __ppp_xmit_process() and ppp_start_xmit() until some
other part of the xmit path drops it.
For L2TP, we rapidly fill the skb's headroom and pppol2tp_xmit() drops
the packet after a few iterations. But PPTP reallocates the headroom
if necessary, letting the loop run and exhaust the machine resources
(as reported in https://bugzilla.kernel.org/show_bug.cgi?id=199109).
Fix this by letting __ppp_xmit_process() enqueue the skb to
ppp->file.xq, so that we can check for recursion before adding it to
the queue. Now ppp_xmit_process() can drop the packet when recursion is
detected.
__ppp_channel_push() is a bit special. It calls __ppp_xmit_process()
without having any actual packet to send. This is used by
ppp_output_wakeup() to re-enable transmission on the parent unit (for
implementations like ppp_async.c, where the .start_xmit() function
might not consume the skb, leaving it in ppp->xmit_pending and
disabling transmission).
Therefore, __ppp_xmit_process() needs to handle the case where skb is
NULL, dequeuing as many packets as possible from ppp->file.xq.
Reported-by: xu heng <xuheng333@zoho.com>
Fixes: 55454a565836 ("ppp: avoid dealock on recursive xmit")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Lebrun [Tue, 20 Mar 2018 14:44:56 +0000 (14:44 +0000)]
ipv6: sr: fix NULL pointer dereference when setting encap source address
When using seg6 in encap mode, we call ipv6_dev_get_saddr() to set the
source address of the outer IPv6 header, in case none was specified.
Using skb->dev can lead to BUG() when it is in an inconsistent state.
This patch uses the net_device attached to the skb's dst instead.
[940807.667429] BUG: unable to handle kernel NULL pointer dereference at
000000000000047c
[940807.762427] IP: ipv6_dev_get_saddr+0x8b/0x1d0
[940807.815725] PGD 0 P4D 0
[940807.847173] Oops: 0000 [#1] SMP PTI
[940807.890073] Modules linked in:
[940807.927765] CPU: 6 PID: 0 Comm: swapper/6 Tainted: G W 4.16.0-rc1-seg6bpf+ #2
[940808.028988] Hardware name: HP ProLiant DL120 G6/ProLiant DL120 G6, BIOS O26 09/06/2010
[940808.128128] RIP: 0010:ipv6_dev_get_saddr+0x8b/0x1d0
[940808.187667] RSP: 0018:
ffff88043fd836b0 EFLAGS:
00010206
[940808.251366] RAX:
0000000000000005 RBX:
ffff88042cb1c860 RCX:
00000000000000fe
[940808.338025] RDX:
00000000000002c0 RSI:
ffff88042cb1c860 RDI:
0000000000004500
[940808.424683] RBP:
ffff88043fd83740 R08:
0000000000000000 R09:
ffffffffffffffff
[940808.511342] R10:
0000000000000040 R11:
0000000000000000 R12:
ffff88042cb1c850
[940808.598012] R13:
ffffffff8208e380 R14:
ffff88042ac8da00 R15:
0000000000000002
[940808.684675] FS:
0000000000000000(0000) GS:
ffff88043fd80000(0000) knlGS:
0000000000000000
[940808.783036] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[940808.852975] CR2:
000000000000047c CR3:
00000004255fe000 CR4:
00000000000006e0
[940808.939634] Call Trace:
[940808.970041] <IRQ>
[940808.995250] ? ip6t_do_table+0x265/0x640
[940809.043341] seg6_do_srh_encap+0x28f/0x300
[940809.093516] ? seg6_do_srh+0x1a0/0x210
[940809.139528] seg6_do_srh+0x1a0/0x210
[940809.183462] seg6_output+0x28/0x1e0
[940809.226358] lwtunnel_output+0x3f/0x70
[940809.272370] ip6_xmit+0x2b8/0x530
[940809.313185] ? ac6_proc_exit+0x20/0x20
[940809.359197] inet6_csk_xmit+0x7d/0xc0
[940809.404173] tcp_transmit_skb+0x548/0x9a0
[940809.453304] __tcp_retransmit_skb+0x1a8/0x7a0
[940809.506603] ? ip6_default_advmss+0x40/0x40
[940809.557824] ? tcp_current_mss+0x24/0x90
[940809.605925] tcp_retransmit_skb+0xd/0x80
[940809.654016] tcp_xmit_retransmit_queue.part.17+0xf9/0x210
[940809.719797] tcp_ack+0xa47/0x1110
[940809.760612] tcp_rcv_established+0x13c/0x570
[940809.812865] tcp_v6_do_rcv+0x151/0x3d0
[940809.858879] tcp_v6_rcv+0xa5c/0xb10
[940809.901770] ? seg6_output+0xdd/0x1e0
[940809.946745] ip6_input_finish+0xbb/0x460
[940809.994837] ip6_input+0x74/0x80
[940810.034612] ? ip6_rcv_finish+0xb0/0xb0
[940810.081663] ipv6_rcv+0x31c/0x4c0
...
Fixes: 6c8702c60b886 ("ipv6: sr: add support for SRH encapsulation and injection with lwtunnels")
Reported-by: Tom Herbert <tom@quantonium.net>
Signed-off-by: David Lebrun <dlebrun@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Lebrun [Tue, 20 Mar 2018 14:44:55 +0000 (14:44 +0000)]
ipv6: sr: fix scheduling in RCU when creating seg6 lwtunnel state
The seg6_build_state() function is called with RCU read lock held,
so we cannot use GFP_KERNEL. This patch uses GFP_ATOMIC instead.
[ 92.770271] =============================
[ 92.770628] WARNING: suspicious RCU usage
[ 92.770921] 4.16.0-rc4+ #12 Not tainted
[ 92.771277] -----------------------------
[ 92.771585] ./include/linux/rcupdate.h:302 Illegal context switch in RCU read-side critical section!
[ 92.772279]
[ 92.772279] other info that might help us debug this:
[ 92.772279]
[ 92.773067]
[ 92.773067] rcu_scheduler_active = 2, debug_locks = 1
[ 92.773514] 2 locks held by ip/2413:
[ 92.773765] #0: (rtnl_mutex){+.+.}, at: [<
00000000e5461720>] rtnetlink_rcv_msg+0x441/0x4d0
[ 92.774377] #1: (rcu_read_lock){....}, at: [<
00000000df4f161e>] lwtunnel_build_state+0x59/0x210
[ 92.775065]
[ 92.775065] stack backtrace:
[ 92.775371] CPU: 0 PID: 2413 Comm: ip Not tainted 4.16.0-rc4+ #12
[ 92.775791] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1.fc27 04/01/2014
[ 92.776608] Call Trace:
[ 92.776852] dump_stack+0x7d/0xbc
[ 92.777130] __schedule+0x133/0xf00
[ 92.777393] ? unwind_get_return_address_ptr+0x50/0x50
[ 92.777783] ? __sched_text_start+0x8/0x8
[ 92.778073] ? rcu_is_watching+0x19/0x30
[ 92.778383] ? kernel_text_address+0x49/0x60
[ 92.778800] ? __kernel_text_address+0x9/0x30
[ 92.779241] ? unwind_get_return_address+0x29/0x40
[ 92.779727] ? pcpu_alloc+0x102/0x8f0
[ 92.780101] _cond_resched+0x23/0x50
[ 92.780459] __mutex_lock+0xbd/0xad0
[ 92.780818] ? pcpu_alloc+0x102/0x8f0
[ 92.781194] ? seg6_build_state+0x11d/0x240
[ 92.781611] ? save_stack+0x9b/0xb0
[ 92.781965] ? __ww_mutex_wakeup_for_backoff+0xf0/0xf0
[ 92.782480] ? seg6_build_state+0x11d/0x240
[ 92.782925] ? lwtunnel_build_state+0x1bd/0x210
[ 92.783393] ? ip6_route_info_create+0x687/0x1640
[ 92.783846] ? ip6_route_add+0x74/0x110
[ 92.784236] ? inet6_rtm_newroute+0x8a/0xd0
Fixes: 6c8702c60b886 ("ipv6: sr: add support for SRH encapsulation and injection with lwtunnels")
Signed-off-by: David Lebrun <dlebrun@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 22 Mar 2018 16:02:50 +0000 (12:02 -0400)]
Merge branch 'aquantia-fixes'
Igor Russkikh says:
====================
Aquantia atlantic hot fixes 03-2018
This is a set of atlantic driver hot fixes for various areas:
Some issues with hardware reset covered,
Fixed napi_poll flood happening on some traffic conditions,
Allow system to change MAC address on live device,
Add pci shutdown handler.
patch v2:
- reverse christmas tree
- remove driver private parameter, replacing it with define.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Tue, 20 Mar 2018 11:40:37 +0000 (14:40 +0300)]
net: aquantia: driver version bump
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Tue, 20 Mar 2018 11:40:36 +0000 (14:40 +0300)]
net: aquantia: Implement pci shutdown callback
We should close link and all NIC operations during shutdown.
On some systems graceful reboot never closes NIC interface on its own,
but only indicates pci device shutdown. Without explicit handler, NIC
rx rings continued to transfer DMA data into prepared buffers while CPU
rebooted already. That caused memory corruptions on soft reboot.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Tue, 20 Mar 2018 11:40:35 +0000 (14:40 +0300)]
net: aquantia: Allow live mac address changes
There is nothing prevents us from changing MAC on the running interface.
Allow this with ndev priv flag.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Tue, 20 Mar 2018 11:40:34 +0000 (14:40 +0300)]
net: aquantia: Add tx clean budget and valid budget handling logic
We should report to napi full budget only when we have more job to do.
Before this fix, on any tx queue cleanup we forced napi to do poll again.
Thats a waste of cpu resources and caused storming with napi polls when
there was at least one tx on each interrupt.
With this fix we report full budget only when there is more job on TX
to do. Or, as before, when rx budget was fully consumed.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Tue, 20 Mar 2018 11:40:33 +0000 (14:40 +0300)]
net: aquantia: Change inefficient wait loop on fw data reads
B1 hardware changes behavior of mailbox interface, it has busy bit
always raised. Data ready condition should be detected by increment
of address register.
Old code has empty `for` loop, and that caused cpu overloads on B1
hardware. aq_nic_service_timer_cb consumed ~100ms because of that.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Tue, 20 Mar 2018 11:40:32 +0000 (14:40 +0300)]
net: aquantia: Fix a regression with reset on old firmware
FW 1.5.58 and below needs a fixed delay even after 0x18 register
is filled. Otherwise, setting MPI_INIT state too fast causes
traffic hang.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Tue, 20 Mar 2018 11:40:31 +0000 (14:40 +0300)]
net: aquantia: Fix hardware reset when SPI may rarely hangup
Under some circumstances (notably using thunderbolt interface) SPI
on chip reset may be in active transaction.
Here we forcibly cleanup SPI to prevent possible hangups.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 22 Mar 2018 15:52:31 +0000 (11:52 -0400)]
Merge branch 's390-qeth-fixes'
Julian Wiedmann says:
====================
s390/qeth: fixes 2018-03-20
Please apply one final set of qeth patches for 4.16.
All of these fix long-standing bugs, so please queue them up for -stable
as well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 20 Mar 2018 06:59:15 +0000 (07:59 +0100)]
s390/qeth: on channel error, reject further cmd requests
When the IRQ handler determines that one of the cmd IO channels has
failed and schedules recovery, block any further cmd requests from
being submitted. The request would inevitably stall, and prevent the
recovery from making progress until the request times out.
This sort of error was observed after Live Guest Relocation, where
the pending IO on the READ channel intentionally gets terminated to
kick-start recovery. Simultaneously the guest executed SIOCETHTOOL,
triggering qeth to issue a QUERY CARD INFO command. The command
then stalled in the inoperabel WRITE channel.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 20 Mar 2018 06:59:14 +0000 (07:59 +0100)]
s390/qeth: lock read device while queueing next buffer
For calling ccw_device_start(), issue_next_read() needs to hold the
device's ccwlock.
This is satisfied for the IRQ handler path (where qeth_irq() gets called
under the ccwlock), but we need explicit locking for the initial call by
the MPC initialization.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 20 Mar 2018 06:59:13 +0000 (07:59 +0100)]
s390/qeth: when thread completes, wake up all waiters
qeth_wait_for_threads() is potentially called by multiple users, make
sure to notify all of them after qeth_clear_thread_running_bit()
adjusted the thread_running_mask. With no timeout, callers would
otherwise stall.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 20 Mar 2018 06:59:12 +0000 (07:59 +0100)]
s390/qeth: free netdevice when removing a card
On removal, a qeth card's netdevice is currently not properly freed
because the call chain looks as follows:
qeth_core_remove_device(card)
lx_remove_device(card)
unregister_netdev(card->dev)
card->dev = NULL !!!
qeth_core_free_card(card)
if (card->dev) !!!
free_netdev(card->dev)
Fix it by free'ing the netdev straight after unregistering. This also
fixes the sysfs-driven layer switch case (qeth_dev_layer2_store()),
where the need to free the current netdevice was not considered at all.
Note that free_netdev() takes care of the netif_napi_del() for us too.
Fixes: 4a71df50047f ("qeth: new qeth device driver")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 22 Mar 2018 15:41:08 +0000 (11:41 -0400)]
Merge branch 'net-phy-Add-general-dummy-stubs-for-MMD-register-access'
Kevin Hao says:
====================
net: phy: Add general dummy stubs for MMD register access
v2:
As suggested by Andrew:
- Add general dummy stubs
- Also use that for the micrel phy
This patch series fix the Ethernet broken on the mpc8315erdb board introduced
by commit
b6b5e8a69118 ("gianfar: Disable EEE autoneg by default").
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Kevin Hao [Tue, 20 Mar 2018 01:44:54 +0000 (09:44 +0800)]
net: phy: micrel: Use the general dummy stubs for MMD register access
The new general dummy stubs for MMD register access were introduced.
Use that for the codes reuse.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kevin Hao [Tue, 20 Mar 2018 01:44:53 +0000 (09:44 +0800)]
net: phy: realtek: Use the dummy stubs for MMD register access for rtl8211b
The Ethernet on mpc8315erdb is broken since commit
b6b5e8a69118
("gianfar: Disable EEE autoneg by default"). The reason is that
even though the rtl8211b doesn't support the MMD extended registers
access, it does return some random values if we trying to access
the MMD register via indirect method. This makes it seem that the
EEE is supported by this phy device. And the subsequent writing to
the MMD registers does cause the phy malfunction. So use the dummy
stubs for the MMD register access to fix this issue.
Fixes: b6b5e8a69118 ("gianfar: Disable EEE autoneg by default")
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kevin Hao [Tue, 20 Mar 2018 01:44:52 +0000 (09:44 +0800)]
net: phy: Add general dummy stubs for MMD register access
For some phy devices, even though they don't support the MMD extended
register access, it does have some side effect if we are trying to
read/write the MMD registers via indirect method. So introduce general
dummy stubs for MMD register access which these devices can use to avoid
such side effect.
Fixes: b6b5e8a69118 ("gianfar: Disable EEE autoneg by default")
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 22 Mar 2018 15:26:13 +0000 (11:26 -0400)]
Merge tag 'batadv-net-for-davem-
20180319' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
Here are some batman-adv bugfixes:
- fix possible IPv6 packet loss when multicast extension is used, by Linus Luessing
- fix SKB handling issues for TTVN and DAT, by Matthias Schiffer (two patches)
- fix include for eventpoll, by Sven Eckelmann
- fix skb checksum for ttvn reroutes, by Sven Eckelmann
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Greg Kroah-Hartman [Wed, 21 Mar 2018 15:45:53 +0000 (16:45 +0100)]
drm: udl: Properly check framebuffer mmap offsets
The memmap options sent to the udl framebuffer driver were not being
checked for all sets of possible crazy values. Fix this up by properly
bounding the allowed values.
Reported-by: Eyal Itkin <eyalit@checkpoint.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180321154553.GA18454@kroah.com
Dave Airlie [Wed, 21 Mar 2018 22:52:21 +0000 (08:52 +1000)]
Merge branch 'drm-fixes-4.16' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
A few more fixes for 4.16. Mostly for displays:
- A fix for DP handling on radeon
- Fix banding on eDP panels
- Fix HBR audio
- Fix for disabling VGA mode on Raven that leads to a corrupt or
blank display on some platforms
* 'drm-fixes-4.16' of git://people.freedesktop.org/~agd5f/linux:
drm/amd/display: Add one to EDID's audio channel count when passing to DC
drm/amd/display: We shouldn't set format_default on plane as atomic driver
drm/amd/display: Fix FMT truncation programming
drm/amd/display: Allow truncation to 10 bits
drm/amd/display: fix dereferencing possible ERR_PTR()
drm/amd/display: Refine disable VGA
drm/amdgpu: Use atomic function to disable crtcs with dc enabled
drm/radeon: Don't turn off DP sink when disconnected
David S. Miller [Wed, 21 Mar 2018 22:12:46 +0000 (18:12 -0400)]
Merge branch 'net-sched-action-idr-leak'
Davide Caratti says:
====================
fix idr leak in actions
This series fixes situations where a temporary failure to install a TC
action results in the permanent impossibility to reuse the configured
value of 'index'.
Thanks to Cong Wang for the initial review.
v2: fix build error in act_ipt.c, reported by kbuild test robot
====================
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Mon, 19 Mar 2018 14:31:28 +0000 (15:31 +0100)]
net/sched: fix idr leak in the error path of tcf_skbmod_init()
tcf_skbmod_init() can fail after the idr has been successfully reserved.
When this happens, every subsequent attempt to configure skbmod rules
using the same idr value will systematically fail with -ENOSPC, unless
the first attempt was done using the 'replace' keyword:
# tc action add action skbmod swap mac index 100
RTNETLINK answers: Cannot allocate memory
We have an error talking to the kernel
# tc action add action skbmod swap mac index 100
RTNETLINK answers: No space left on device
We have an error talking to the kernel
# tc action add action skbmod swap mac index 100
RTNETLINK answers: No space left on device
We have an error talking to the kernel
...
Fix this in tcf_skbmod_init(), ensuring that tcf_idr_release() is called
on the error path when the idr has been reserved, but not yet inserted.
Also, don't test 'ovr' in the error path, to avoid a 'replace' failure
implicitly become a 'delete' that leaks refcount in act_skbmod module:
# rmmod act_skbmod; modprobe act_skbmod
# tc action add action skbmod swap mac index 100
# tc action add action skbmod swap mac continue index 100
RTNETLINK answers: File exists
We have an error talking to the kernel
# tc action replace action skbmod swap mac continue index 100
RTNETLINK answers: Cannot allocate memory
We have an error talking to the kernel
# tc action list action skbmod
#
# rmmod act_skbmod
rmmod: ERROR: Module act_skbmod is in use
Fixes: 65a206c01e8e ("net/sched: Change act_api and act_xxx modules to use IDR")
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Mon, 19 Mar 2018 14:31:27 +0000 (15:31 +0100)]
net/sched: fix idr leak in the error path of tcf_vlan_init()
tcf_vlan_init() can fail after the idr has been successfully reserved.
When this happens, every subsequent attempt to configure vlan rules using
the same idr value will systematically fail with -ENOSPC, unless the first
attempt was done using the 'replace' keyword.
# tc action add action vlan pop index 100
RTNETLINK answers: Cannot allocate memory
We have an error talking to the kernel
# tc action add action vlan pop index 100
RTNETLINK answers: No space left on device
We have an error talking to the kernel
# tc action add action vlan pop index 100
RTNETLINK answers: No space left on device
We have an error talking to the kernel
...
Fix this in tcf_vlan_init(), ensuring that tcf_idr_release() is called on
the error path when the idr has been reserved, but not yet inserted. Also,
don't test 'ovr' in the error path, to avoid a 'replace' failure implicitly
become a 'delete' that leaks refcount in act_vlan module:
# rmmod act_vlan; modprobe act_vlan
# tc action add action vlan push id 5 index 100
# tc action replace action vlan push id 7 index 100
RTNETLINK answers: Cannot allocate memory
We have an error talking to the kernel
# tc action list action vlan
#
# rmmod act_vlan
rmmod: ERROR: Module act_vlan is in use
Fixes: 4c5b9d9642c8 ("act_vlan: VLAN action rewrite to use RCU lock/unlock and update")
Fixes: 65a206c01e8e ("net/sched: Change act_api and act_xxx modules to use IDR")
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Mon, 19 Mar 2018 14:31:26 +0000 (15:31 +0100)]
net/sched: fix idr leak in the error path of __tcf_ipt_init()
__tcf_ipt_init() can fail after the idr has been successfully reserved.
When this happens, subsequent attempts to configure xt/ipt rules using
the same idr value systematically fail with -ENOSPC:
# tc action add action xt -j LOG --log-prefix test1 index 100
tablename: mangle hook: NF_IP_POST_ROUTING
target: LOG level warning prefix "test1" index 100
RTNETLINK answers: Cannot allocate memory
We have an error talking to the kernel
Command "(null)" is unknown, try "tc actions help".
# tc action add action xt -j LOG --log-prefix test1 index 100
tablename: mangle hook: NF_IP_POST_ROUTING
target: LOG level warning prefix "test1" index 100
RTNETLINK answers: No space left on device
We have an error talking to the kernel
Command "(null)" is unknown, try "tc actions help".
# tc action add action xt -j LOG --log-prefix test1 index 100
tablename: mangle hook: NF_IP_POST_ROUTING
target: LOG level warning prefix "test1" index 100
RTNETLINK answers: No space left on device
We have an error talking to the kernel
...
Fix this in the error path of __tcf_ipt_init(), calling tcf_idr_release()
in place of tcf_idr_cleanup(). Since tcf_ipt_release() can now be called
when tcfi_t is NULL, we also need to protect calls to ipt_destroy_target()
to avoid NULL pointer dereference.
Fixes: 65a206c01e8e ("net/sched: Change act_api and act_xxx modules to use IDR")
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Mon, 19 Mar 2018 14:31:25 +0000 (15:31 +0100)]
net/sched: fix idr leak in the error path of tcp_pedit_init()
tcf_pedit_init() can fail to allocate 'keys' after the idr has been
successfully reserved. When this happens, subsequent attempts to configure
a pedit rule using the same idr value systematically fail with -ENOSPC:
# tc action add action pedit munge ip ttl set 63 index 100
RTNETLINK answers: Cannot allocate memory
We have an error talking to the kernel
# tc action add action pedit munge ip ttl set 63 index 100
RTNETLINK answers: No space left on device
We have an error talking to the kernel
# tc action add action pedit munge ip ttl set 63 index 100
RTNETLINK answers: No space left on device
We have an error talking to the kernel
...
Fix this in the error path of tcf_act_pedit_init(), calling
tcf_idr_release() in place of tcf_idr_cleanup().
Fixes: 65a206c01e8e ("net/sched: Change act_api and act_xxx modules to use IDR")
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Williams [Wed, 21 Mar 2018 22:12:07 +0000 (15:12 -0700)]
libnvdimm, nfit: fix persistence domain reporting
The persistence domain is a point in the platform where once writes
reach that destination the platform claims it will make them persistent
relative to power loss. In the ACPI NFIT this is currently communicated
as 2 bits in the "NFIT - Platform Capabilities Structure". The bits
comprise a hierarchy, i.e. bit0 "CPU Cache Flush to NVDIMM Durability on
Power Loss Capable" implies bit1 "Memory Controller Flush to NVDIMM
Durability on Power Loss Capable".
Commit
96c3a239054a "libnvdimm: expose platform persistence attr..."
shows the persistence domain as flags, but it's really an enumerated
hierarchy.
Fix this newly introduced user ABI to show the closest available
persistence domain before userspace develops dependencies on seeing, or
needing to develop code to tolerate, the raw NFIT flags communicated
through the libnvdimm-generic region attribute.
Fixes: 96c3a239054a ("libnvdimm: expose platform persistence attr...")
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Davide Caratti [Mon, 19 Mar 2018 14:31:24 +0000 (15:31 +0100)]
net/sched: fix idr leak in the error path of tcf_act_police_init()
tcf_act_police_init() can fail after the idr has been successfully
reserved (e.g., qdisc_get_rtab() may return NULL). When this happens,
subsequent attempts to configure a police rule using the same idr value
systematiclly fail with -ENOSPC:
# tc action add action police rate 1000 burst 1000 drop index 100
RTNETLINK answers: Cannot allocate memory
We have an error talking to the kernel
# tc action add action police rate 1000 burst 1000 drop index 100
RTNETLINK answers: No space left on device
We have an error talking to the kernel
# tc action add action police rate 1000 burst 1000 drop index 100
RTNETLINK answers: No space left on device
...
Fix this in the error path of tcf_act_police_init(), calling
tcf_idr_release() in place of tcf_idr_cleanup().
Fixes: 65a206c01e8e ("net/sched: Change act_api and act_xxx modules to use IDR")
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Mon, 19 Mar 2018 14:31:23 +0000 (15:31 +0100)]
net/sched: fix idr leak in the error path of tcf_simp_init()
if the kernel fails to duplicate 'sdata', creation of a new action fails
with -ENOMEM. However, subsequent attempts to install the same action
using the same value of 'index' systematically fail with -ENOSPC, and
that value of 'index' will no more be usable by act_simple, until rmmod /
insmod of act_simple.ko is done:
# tc actions add action simple sdata hello index 100
# tc actions list action simple
action order 0: Simple <hello>
index 100 ref 1 bind 0
# tc actions flush action simple
# tc actions add action simple sdata hello index 100
RTNETLINK answers: Cannot allocate memory
We have an error talking to the kernel
# tc actions flush action simple
# tc actions add action simple sdata hello index 100
RTNETLINK answers: No space left on device
We have an error talking to the kernel
# tc actions add action simple sdata hello index 100
RTNETLINK answers: No space left on device
We have an error talking to the kernel
...
Fix this in the error path of tcf_simp_init(), calling tcf_idr_release()
in place of tcf_idr_cleanup().
Fixes: 65a206c01e8e ("net/sched: Change act_api and act_xxx modules to use IDR")
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Mon, 19 Mar 2018 14:31:22 +0000 (15:31 +0100)]
net/sched: fix idr leak on the error path of tcf_bpf_init()
when the following command sequence is entered
# tc action add action bpf bytecode '4,40 0 0 12,31 0 1 2048,6 0 0 262144,6 0 0 0' index 100
RTNETLINK answers: Invalid argument
We have an error talking to the kernel
# tc action add action bpf bytecode '4,40 0 0 12,21 0 1 2048,6 0 0 262144,6 0 0 0' index 100
RTNETLINK answers: No space left on device
We have an error talking to the kernel
act_bpf correctly refuses to install the first TC rule, because 31 is not
a valid instruction. However, it refuses to install the second TC rule,
even if the BPF code is correct. Furthermore, it's no more possible to
install any other rule having the same value of 'index' until act_bpf
module is unloaded/inserted again. After the idr has been reserved, call
tcf_idr_release() instead of tcf_idr_cleanup(), to fix this issue.
Fixes: 65a206c01e8e ("net/sched: Change act_api and act_xxx modules to use IDR")
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Mon, 19 Mar 2018 14:57:11 +0000 (14:57 +0000)]
qede: fix spelling mistake: "registeration" -> "registration"
Trivial fix to spelling mistakes in DP_ERR error message text and
comments
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Mon, 19 Mar 2018 14:32:59 +0000 (14:32 +0000)]
bnx2x: fix spelling mistake: "registeration" -> "registration"
Trivial fix to spelling mistake in BNX2X_ERR error message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Sudarsana Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Williams [Wed, 21 Mar 2018 21:06:23 +0000 (14:06 -0700)]
libnvdimm, region: hide persistence_domain when unknown
Similar to other region attributes, do not emit the persistence_domain
attribute if its contents are empty.
Fixes: 96c3a239054a ("libnvdimm: expose platform persistence attr...")
Cc: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
David S. Miller [Wed, 21 Mar 2018 16:09:04 +0000 (12:09 -0400)]
Merge git://git./pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2018-03-21
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Follow-up fix to the fault injection framework to prevent jump
optimization on the kprobe by installing a dummy post-handler,
from Masami.
2) Drop bpf_perf_prog_read_value helper from tracepoint type programs
which was mistakenly added there and would otherwise crash due to
wrong input context, from Yonghong.
3) Fix a crash in BPF fs when compiled with clang. Code appears to
be fine just that clang tries to overly aggressive optimize in
non C conform ways, therefore fix the kernel's Makefile to
generally prevent such issues, from Daniel.
4) Skip unnecessary capability checks in bpf syscall, which is otherwise
triggering unnecessary security hooks on capability checking and
causing false alarms on unprivileged processes trying to access
CAP_SYS_ADMIN restricted infra, from Chenbo.
5) Fix the test_bpf.ko module when CONFIG_BPF_JIT_ALWAYS_ON is set
with regards to a test case that is really just supposed to fail
on x8_64 JIT but not others, from Thadeu.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Chris Wilson [Tue, 20 Mar 2018 10:04:48 +0000 (10:04 +0000)]
drm/i915: Specify which engines to reset following semaphore/event lockups
If the GPU is stuck waiting for an event or for a semaphore, we need to
reset the GPU in order to recover. We have to tell the reset routine
which engines we want reset, but we were still using the old interface
and declaring it as "not-fatal".
Fixes: 14b730fcb8d9 ("drm/i915/tdr: Prepare error handler to accept mask of hung engines")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180320100449.1360-1-chris@chris-wilson.co.uk
(cherry picked from commit
ca98317b89428e6ac17be0938b467ed78654dd56)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Johannes Berg [Wed, 21 Mar 2018 10:00:14 +0000 (11:00 +0100)]
ath9k_htc: use non-QoS NDP for AP probing
When switching mac80211 to use QoS NDP, it turned out that
ath9k_htc is somehow broken by this, e.g. see
https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=891060.
Fix this by using the new mac80211 flag to go back to the
old, incorrect, behaviour for this driver.
Fixes: 7b6ddeaf27ec ("mac80211: use QoS NDP for AP probing")
Reported-by: Ben Caradoc-Davies <ben@transient.nz>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Andrew Zaborowski [Wed, 21 Mar 2018 07:05:18 +0000 (08:05 +0100)]
mac80211_hwsim: Set wmediumd for new radios
Set the wmediumd to the net's wmediumd when the radio gets created.
Radios created after HWSIM_CMD_REGISTER don't currently get their
data->wmediumd set and the userspace would need to reconnect to
netlink to be able to call HWSIM_CMD_REGISTER again.
Alternatively I think data->netgroup and data->wmedium could be
replaced with a pointer to hwsim_net.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Adrian Hunter [Wed, 21 Mar 2018 09:49:40 +0000 (11:49 +0200)]
mmc: sdhci-acpi: Fix IRQ 0
Zero is a valid IRQ number and is being used on some CHT tablets. Stop
treating it as an error.
Reported-by: Luke Ross <luke@lukeross.name>
Fixes: 1b7ba57ecc86 ("mmc: sdhci-acpi: Handle return value of platform_get_irq")
Cc: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ben Caradoc-Davies [Sun, 18 Mar 2018 23:57:44 +0000 (12:57 +1300)]
mac80211: add ieee80211_hw flag for QoS NDP support
Commit
7b6ddeaf27ec ("mac80211: use QoS NDP for AP probing") added an
argument qos_ok to ieee80211_nullfunc_get to support QoS NDP. Despite
the claim in the commit log "Change all the drivers to *not* allow
QoS NDP for now, even though it looks like most of them should be OK
with that", this commit enables QoS NDP in response to beacons (see
change to mlme.c:ieee80211_send_nullfunc), causing ath9k_htc to lose
IP connectivity. See:
https://patchwork.kernel.org/patch/
10241109/
https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=891060
Introduce a hardware flag to allow such buggy drivers to override the
correct default behaviour of mac80211 of sending QoS NDP packets.
Signed-off-by: Ben Caradoc-Davies <ben@transient.nz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Thomas Hellstrom [Wed, 21 Mar 2018 09:18:38 +0000 (10:18 +0100)]
drm/vmwgfx: Fix a destoy-while-held mutex problem.
When validating legacy surfaces, the backup bo might be destroyed at
surface validate time. However, the kms resource validation code may have
the bo reserved, so we will destroy a locked mutex. While there shouldn't
be any other users of that mutex when it is destroyed, it causes a lock
leak and thus throws a lockdep error.
Fix this by having the kms resource validation code hold a reference to
the bo while we have it reserved. We do this by introducing a validation
context which might come in handy when the kms code is extended to validate
multiple resources or buffers.
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Thomas Hellstrom [Thu, 8 Mar 2018 09:07:37 +0000 (10:07 +0100)]
drm/vmwgfx: Fix black screen and device errors when running without fbdev
When we are running without fbdev, transitioning from the login screen to
X or gnome-shell/wayland will cause a vt switch and the driver will disable
svga mode, losing all modesetting resources. However, the kms atomic state
does not reflect that and may think that a crtc is still turned on, which
will cause device errors when we try to bind an fb to the crtc, and the
screen will remain black.
Fix this by turning off all kms resources before disabling svga mode.
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Daniel Stone [Tue, 20 Mar 2018 22:58:39 +0000 (22:58 +0000)]
drm: Reject getfb for multi-plane framebuffers
getfb can only return a single plane, so reject attempts to use it with
multi-plane framebuffers.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reported-by: Daniel van Vugt <daniel.van.vugt@canonical.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fixes: 308e5bcbdb10 ("drm: add an fb creation ioctl that takes a pixel format v5")
Cc: stable@vger.kernel.org # v3.3+
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105518
Link: https://patchwork.freedesktop.org/patch/msgid/20180320225839.30905-1-daniels@collabora.com
Harry Wentland [Wed, 7 Mar 2018 18:45:33 +0000 (13:45 -0500)]
drm/amd/display: Add one to EDID's audio channel count when passing to DC
DC takes channel count to mean the actual count. cea_sad's channels
represent it as number of channels - 1.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Harry Wentland [Tue, 6 Mar 2018 16:14:12 +0000 (11:14 -0500)]
drm/amd/display: We shouldn't set format_default on plane as atomic driver
This is still a leftover from early atomic brinup days.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Mikita Lipski [Wed, 7 Mar 2018 16:12:20 +0000 (11:12 -0500)]
drm/amd/display: Fix FMT truncation programming
Switch the order of parameters being set for depth
and mode of truncation, as it previously was not correct
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Mikita Lipski [Wed, 7 Mar 2018 15:49:23 +0000 (10:49 -0500)]
drm/amd/display: Allow truncation to 10 bits
The truncation isn't being programmed if the truncation
depth is set to 2, it causes an issue with dce11.2 asic
using 6bit eDP panel. It required to truncate 12:10 in order to
perform spatial dither 10:6.
This change will allow 12:10 truncation to be enabled.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Dave Airlie [Wed, 21 Mar 2018 03:56:07 +0000 (13:56 +1000)]
Merge tag 'exynos-drm-fixes-for-v4.16-rc6' of git://git./linux/kernel/git/daeinki/drm-exynos into drm-fixes
Add a device tree property description for hdmi device node
. '#sound-dai-cells' property is required to describe link between
the HDMI IP block and the SoC's audio subsystem and Exynos SoC device
tree files already have this property but we missed its description.
* tag 'exynos-drm-fixes-for-v4.16-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
dt-bindings: exynos: Document #sound-dai-cells property of the HDMI node
Dave Airlie [Wed, 21 Mar 2018 03:55:47 +0000 (13:55 +1000)]
Merge tag 'drm/tegra/for-4.16-rc7-fixes' of git://anongit.freedesktop.org/tegra/linux into drm-fixes
drm/tegra: Fixes for v4.16-rc7
This contains two small fixes for the alpha blending support that was
merged into v4.16-rc1 and a fix for connector reference leaks caused by
the fact that display pipelines are no longer automatically disabled if
the framebuffer is removed.
Furthermore this contains a fix for a crash on IOMMU detach at driver
unbind time and a regulator enable/disable unbalance fix.
* tag 'drm/tegra/for-4.16-rc7-fixes' of git://anongit.freedesktop.org/tegra/linux:
drm/tegra: Shutdown on driver unbind
drm/tegra: dsi: Don't disable regulator on ->exit()
drm/tegra: dc: Detach IOMMU group from domain only once
drm/tegra: plane: Correct legacy blending
drm/tegra: plane: Fix RGB565 format on older Tegra
Linus Torvalds [Wed, 21 Mar 2018 00:44:27 +0000 (17:44 -0700)]
Merge tag 'clk-fixes-for-linus' of git://git./linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A late collection of fixes for regressions seen this release cycle.
Normally I send this earlier than now but real life got in the way.
Things are back to normal now.
There's the normal set of SoC driver fixes: i.MX boot warning, TI
display clks, allwinner clk ops being wrong (fun), driver probe
badness on error paths, correctness fix for the new aspeed driver, and
even a fix for a race condition in the bcm2835 clk driver.
At the core framework level we also got some fixes for the clk phase
API caching at the wrong time, better handling of the enabled state of
orphan clks, and a fix for a newly introduced bug in how we handle
rate calculations for pass-through clks"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: bcm2835: Protect sections updating shared registers
clk: bcm2835: Fix ana->maskX definitions
clk: aspeed: Prevent reset if clock is enabled
clk: aspeed: Fix is_enabled for certain clocks
clk: qcom: msm8916: Fix return value check in qcom_apcs_msm8916_clk_probe()
clk: hisilicon: hi3660：Fix potential NULL dereference in hi3660_stub_clk_probe()
clk: fix determine rate error with pass-through clock
clk: migrate the count of orphaned clocks at init
clk: update cached phase to respect the fact when setting phase
clk: ti: am43xx: add set-rate-parent support for display clkctrl clock
clk: ti: am33xx: add set-rate-parent support for display clkctrl clock
clk: ti: clkctrl: add support for CLK_SET_RATE_PARENT flag
clk: imx51-imx53: Fix UART4/5 registration on i.MX50 and i.MX53
clk: sunxi-ng: a31: Fix CLK_OUT_* clock ops
Daniel Borkmann [Wed, 21 Mar 2018 00:18:24 +0000 (01:18 +0100)]
kbuild: disable clang's default use of -fmerge-all-constants
Prasad reported that he has seen crashes in BPF subsystem with netd
on Android with arm64 in the form of (note, the taint is unrelated):
[ 4134.721483] Unable to handle kernel paging request at virtual address
800000001
[ 4134.820925] Mem abort info:
[ 4134.901283] Exception class = DABT (current EL), IL = 32 bits
[ 4135.016736] SET = 0, FnV = 0
[ 4135.119820] EA = 0, S1PTW = 0
[ 4135.201431] Data abort info:
[ 4135.301388] ISV = 0, ISS = 0x00000021
[ 4135.359599] CM = 0, WnR = 0
[ 4135.470873] user pgtable: 4k pages, 39-bit VAs, pgd =
ffffffe39b946000
[ 4135.499757] [
0000000800000001] *pgd=
0000000000000000, *pud=
0000000000000000
[ 4135.660725] Internal error: Oops:
96000021 [#1] PREEMPT SMP
[ 4135.674610] Modules linked in:
[ 4135.682883] CPU: 5 PID: 1260 Comm: netd Tainted: G S W 4.14.19+ #1
[ 4135.716188] task:
ffffffe39f4aa380 task.stack:
ffffff801d4e0000
[ 4135.731599] PC is at bpf_prog_add+0x20/0x68
[ 4135.741746] LR is at bpf_prog_inc+0x20/0x2c
[ 4135.751788] pc : [<
ffffff94ab7ad584>] lr : [<
ffffff94ab7ad638>] pstate:
60400145
[ 4135.769062] sp :
ffffff801d4e3ce0
[...]
[ 4136.258315] Process netd (pid: 1260, stack limit = 0xffffff801d4e0000)
[ 4136.273746] Call trace:
[...]
[ 4136.442494] 3ca0:
ffffff94ab7ad584 0000000060400145 ffffffe3a01bf8f8 0000000000000006
[ 4136.460936] 3cc0:
0000008000000000 ffffff94ab844204 ffffff801d4e3cf0 ffffff94ab7ad584
[ 4136.479241] [<
ffffff94ab7ad584>] bpf_prog_add+0x20/0x68
[ 4136.491767] [<
ffffff94ab7ad638>] bpf_prog_inc+0x20/0x2c
[ 4136.504536] [<
ffffff94ab7b5d08>] bpf_obj_get_user+0x204/0x22c
[ 4136.518746] [<
ffffff94ab7ade68>] SyS_bpf+0x5a8/0x1a88
Android's netd was basically pinning the uid cookie BPF map in BPF
fs (/sys/fs/bpf/traffic_cookie_uid_map) and later on retrieving it
again resulting in above panic. Issue is that the map was wrongly
identified as a prog! Above kernel was compiled with clang 4.0,
and it turns out that clang decided to merge the bpf_prog_iops and
bpf_map_iops into a single memory location, such that the two i_ops
could then not be distinguished anymore.
Reason for this miscompilation is that clang has the more aggressive
-fmerge-all-constants enabled by default. In fact, clang source code
has a comment about it in lib/AST/ExprConstant.cpp on why it is okay
to do so:
Pointers with different bases cannot represent the same object.
(Note that clang defaults to -fmerge-all-constants, which can
lead to inconsistent results for comparisons involving the address
of a constant; this generally doesn't matter in practice.)
The issue never appeared with gcc however, since gcc does not enable
-fmerge-all-constants by default and even *explicitly* states in
it's option description that using this flag results in non-conforming
behavior, quote from man gcc:
Languages like C or C++ require each variable, including multiple
instances of the same variable in recursive calls, to have distinct
locations, so using this option results in non-conforming behavior.
There are also various clang bug reports open on that matter [1],
where clang developers acknowledge the non-conforming behavior,
and refer to disabling it with -fno-merge-all-constants. But even
if this gets fixed in clang today, there are already users out there
that triggered this. Thus, fix this issue by explicitly adding
-fno-merge-all-constants to the kernel's Makefile to generically
disable this optimization, since potentially other places in the
kernel could subtly break as well.
Note, there is also a flag called -fmerge-constants (not supported
by clang), which is more conservative and only applies to strings
and it's enabled in gcc's -O/-O2/-O3/-Os optimization levels. In
gcc's code, the two flags -fmerge-{all-,}constants share the same
variable internally, so when disabling it via -fno-merge-all-constants,
then we really don't merge any const data (e.g. strings), and text
size increases with gcc (14,927,214 -> 14,942,646 for vmlinux.o).
$ gcc -fverbose-asm -O2 foo.c -S -o foo.S
-> foo.S lists -fmerge-constants under options enabled
$ gcc -fverbose-asm -O2 -fno-merge-all-constants foo.c -S -o foo.S
-> foo.S doesn't list -fmerge-constants under options enabled
$ gcc -fverbose-asm -O2 -fno-merge-all-constants -fmerge-constants foo.c -S -o foo.S
-> foo.S lists -fmerge-constants under options enabled
Thus, as a workaround we need to set both -fno-merge-all-constants
*and* -fmerge-constants in the Makefile in order for text size to
stay as is.
[1] https://bugs.llvm.org/show_bug.cgi?id=18538
Reported-by: Prasad Sodagudi <psodagud@codeaurora.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Chenbo Feng <fengc@google.com>
Cc: Richard Smith <richard-llvm@metafoo.co.uk>
Cc: Chandler Carruth <chandlerc@gmail.com>
Cc: linux-kernel@vger.kernel.org
Tested-by: Prasad Sodagudi <psodagud@codeaurora.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Linus Torvalds [Wed, 21 Mar 2018 00:39:07 +0000 (17:39 -0700)]
Merge tag 'for-linus' of git://git./linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"Not much exciting here, almost entirely syzkaller fixes.
This is going to be on ongoing theme for some time, I think. Both
Google and Mellanox are now running syzkaller on different parts of
the user API.
Summary:
- Many bug fixes related to syzkaller from Leon Romanovsky. These are
still for the mlx driver and ucma interface.
- Fix a situation with port reuse for iWarp, discovered during
scale-up testing
- Bug fixes for the profile and restrack patches accepted during this
merge window
- Compile warning cleanups from Arnd, this is apparently the last
warning to make 32 bit builds quiet"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/ucma: Ensure that CM_ID exists prior to access it
RDMA/verbs: Remove restrack entry from XRCD structure
RDMA/ucma: Fix use-after-free access in ucma_close
RDMA/ucma: Check AF family prior resolving address
infiniband: bnxt_re: use BIT_ULL() for 64-bit bit masks
infiniband: qplib_fp: fix pointer cast
IB/mlx5: Fix cleanup order on unload
RDMA/ucma: Don't allow join attempts for unsupported AF family
RDMA/ucma: Fix access to non-initialized CM_ID object
RDMA/core: Do not use invalid destination in determining port reuse
RDMA/mlx5: Fix crash while accessing garbage pointer and freed memory
IB/mlx5: Fix integer overflows in mlx5_ib_create_srq
IB/mlx5: Fix out-of-bounds read in create_raw_packet_qp_rq
Linus Torvalds [Tue, 20 Mar 2018 23:59:01 +0000 (16:59 -0700)]
Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
- one driver patch (qla2xxx) which fixes a problem caused by an
existing regression fix (FCP discovery is failing)
- one generic fix to a longstanding bug in libsas that causes I/O
eventually to hang to the device in the face of ATA error recovery.
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: qla2xxx: Remove FC_NO_LOOP_ID for FCP and FC-NVMe Discovery
scsi: libsas: defer ata device eh commands to libata
Linus Torvalds [Tue, 20 Mar 2018 23:10:26 +0000 (16:10 -0700)]
Merge tag 'nfsd-4.16-1' of git://linux-nfs.org/~bfields/linux
Pull nfsd fix from Bruce Fields:
"Just one fix for an occasional panic from Jeff Layton"
* tag 'nfsd-4.16-1' of git://linux-nfs.org/~bfields/linux:
nfsd: remove blocked locks on client teardown
Chenbo Feng [Tue, 20 Mar 2018 00:57:27 +0000 (17:57 -0700)]
bpf: skip unnecessary capability check
The current check statement in BPF syscall will do a capability check
for CAP_SYS_ADMIN before checking sysctl_unprivileged_bpf_disabled. This
code path will trigger unnecessary security hooks on capability checking
and cause false alarms on unprivileged process trying to get CAP_SYS_ADMIN
access. This can be resolved by simply switch the order of the statement
and CAP_SYS_ADMIN is not required anyway if unprivileged bpf syscall is
allowed.
Signed-off-by: Chenbo Feng <fengc@google.com>
Acked-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Yonghong Song [Tue, 20 Mar 2018 18:19:17 +0000 (11:19 -0700)]
trace/bpf: remove helper bpf_perf_prog_read_value from tracepoint type programs
Commit
4bebdc7a85aa ("bpf: add helper bpf_perf_prog_read_value")
added helper bpf_perf_prog_read_value so that perf_event type program
can read event counter and enabled/running time.
This commit, however, introduced a bug which allows this helper
for tracepoint type programs. This is incorrect as bpf_perf_prog_read_value
needs to access perf_event through its bpf_perf_event_data_kern type context,
which is not available for tracepoint type program.
This patch fixed the issue by separating bpf_func_proto between tracepoint
and perf_event type programs and removed bpf_perf_prog_read_value
from tracepoint func prototype.
Fixes: 4bebdc7a85aa ("bpf: add helper bpf_perf_prog_read_value")
Reported-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Thadeu Lima de Souza Cascardo [Tue, 20 Mar 2018 12:58:51 +0000 (09:58 -0300)]
test_bpf: Fix testing with CONFIG_BPF_JIT_ALWAYS_ON=y on other arches
Function bpf_fill_maxinsns11 is designed to not be able to be JITed on
x86_64. So, it fails when CONFIG_BPF_JIT_ALWAYS_ON=y, and
commit
09584b406742 ("bpf: fix selftests/bpf test_kmod.sh failure when
CONFIG_BPF_JIT_ALWAYS_ON=y") makes sure that failure is detected on that
case.
However, it does not fail on other architectures, which have a different
JIT compiler design. So, test_bpf has started to fail to load on those.
After this fix, test_bpf loads fine on both x86_64 and ppc64el.
Fixes: 09584b406742 ("bpf: fix selftests/bpf test_kmod.sh failure when CONFIG_BPF_JIT_ALWAYS_ON=y")
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Reviewed-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Linus Torvalds [Tue, 20 Mar 2018 19:16:59 +0000 (12:16 -0700)]
kvm/x86: fix icebp instruction handling
The undocumented 'icebp' instruction (aka 'int1') works pretty much like
'int3' in the absense of in-circuit probing equipment (except,
obviously, that it raises #DB instead of raising #BP), and is used by
some validation test-suites as such.
But Andy Lutomirski noticed that his test suite acted differently in kvm
than on bare hardware.
The reason is that kvm used an inexact test for the icebp instruction:
it just assumed that an all-zero VM exit qualification value meant that
the VM exit was due to icebp.
That is not unlike the guess that do_debug() does for the actual
exception handling case, but it's purely a heuristic, not an absolute
rule. do_debug() does it because it wants to ascribe _some_ reasons to
the #DB that happened, and an empty %dr6 value means that 'icebp' is the
most likely casue and we have no better information.
But kvm can just do it right, because unlike the do_debug() case, kvm
actually sees the real reason for the #DB in the VM-exit interruption
information field.
So instead of relying on an inexact heuristic, just use the actual VM
exit information that says "it was 'icebp'".
Right now the 'icebp' instruction isn't technically documented by Intel,
but that will hopefully change. The special "privileged software
exception" information _is_ actually mentioned in the Intel SDM, even
though the cause of it isn't enumerated.
Reported-by: Andy Lutomirski <luto@kernel.org>
Tested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Leon Romanovsky [Tue, 20 Mar 2018 15:05:13 +0000 (17:05 +0200)]
RDMA/ucma: Ensure that CM_ID exists prior to access it
Prior to access UCMA commands, the context should be initialized
and connected to CM_ID with ucma_create_id(). In case user skips
this step, he can provide non-valid ctx without CM_ID and cause
to multiple NULL dereferences.
Also there are situations where the create_id can be raced with
other user access, ensure that the context is only shared to
other threads once it is fully initialized to avoid the races.
[ 109.088108] BUG: unable to handle kernel NULL pointer dereference at
0000000000000020
[ 109.090315] IP: ucma_connect+0x138/0x1d0
[ 109.092595] PGD
80000001dc02d067 P4D
80000001dc02d067 PUD
1da9ef067 PMD 0
[ 109.095384] Oops: 0000 [#1] SMP KASAN PTI
[ 109.097834] CPU: 0 PID: 663 Comm: uclose Tainted: G B
4.16.0-rc1-00062-g2975d5de6428 #45
[ 109.100816] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
rel-1.11.0-0-g63451fca13-prebuilt.qemu-project.org 04/01/2014
[ 109.105943] RIP: 0010:ucma_connect+0x138/0x1d0
[ 109.108850] RSP: 0018:
ffff8801c8567a80 EFLAGS:
00010246
[ 109.111484] RAX:
0000000000000000 RBX:
1ffff100390acf50 RCX:
ffffffff9d7812e2
[ 109.114496] RDX:
1ffffffff3f507a5 RSI:
0000000000000297 RDI:
0000000000000297
[ 109.117490] RBP:
ffff8801daa15600 R08:
0000000000000000 R09:
ffffed00390aceeb
[ 109.120429] R10:
0000000000000001 R11:
ffffed00390aceea R12:
0000000000000000
[ 109.123318] R13:
0000000000000120 R14:
ffff8801de6459c0 R15:
0000000000000118
[ 109.126221] FS:
00007fabb68d6700(0000) GS:
ffff8801e5c00000(0000) knlGS:
0000000000000000
[ 109.129468] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[ 109.132523] CR2:
0000000000000020 CR3:
00000001d45d8003 CR4:
00000000003606b0
[ 109.135573] DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
[ 109.138716] DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
[ 109.142057] Call Trace:
[ 109.144160] ? ucma_listen+0x110/0x110
[ 109.146386] ? wake_up_q+0x59/0x90
[ 109.148853] ? futex_wake+0x10b/0x2a0
[ 109.151297] ? save_stack+0x89/0xb0
[ 109.153489] ? _copy_from_user+0x5e/0x90
[ 109.155500] ucma_write+0x174/0x1f0
[ 109.157933] ? ucma_resolve_route+0xf0/0xf0
[ 109.160389] ? __mod_node_page_state+0x1d/0x80
[ 109.162706] __vfs_write+0xc4/0x350
[ 109.164911] ? kernel_read+0xa0/0xa0
[ 109.167121] ? path_openat+0x1b10/0x1b10
[ 109.169355] ? fsnotify+0x899/0x8f0
[ 109.171567] ? fsnotify_unmount_inodes+0x170/0x170
[ 109.174145] ? __fget+0xa8/0xf0
[ 109.177110] vfs_write+0xf7/0x280
[ 109.179532] SyS_write+0xa1/0x120
[ 109.181885] ? SyS_read+0x120/0x120
[ 109.184482] ? compat_start_thread+0x60/0x60
[ 109.187124] ? SyS_read+0x120/0x120
[ 109.189548] do_syscall_64+0xeb/0x250
[ 109.192178] entry_SYSCALL_64_after_hwframe+0x21/0x86
[ 109.194725] RIP: 0033:0x7fabb61ebe99
[ 109.197040] RSP: 002b:
00007fabb68d5e98 EFLAGS:
00000202 ORIG_RAX:
0000000000000001
[ 109.200294] RAX:
ffffffffffffffda RBX:
0000000000000000 RCX:
00007fabb61ebe99
[ 109.203399] RDX:
0000000000000120 RSI:
00000000200001c0 RDI:
0000000000000004
[ 109.206548] RBP:
00007fabb68d5ec0 R08:
0000000000000000 R09:
0000000000000000
[ 109.209902] R10:
0000000000000000 R11:
0000000000000202 R12:
00007fabb68d5fc0
[ 109.213327] R13:
0000000000000000 R14:
00007fff40ab2430 R15:
00007fabb68d69c0
[ 109.216613] Code: 88 44 24 2c 0f b6 84 24 6e 01 00 00 88 44 24 2d 0f
b6 84 24 69 01 00 00 88 44 24 2e 8b 44 24 60 89 44 24 30 e8 da f6 06 ff
31 c0 <66> 41 83 7c 24 20 1b 75 04 8b 44 24 64 48 8d 74 24 20 4c 89 e7
[ 109.223602] RIP: ucma_connect+0x138/0x1d0 RSP:
ffff8801c8567a80
[ 109.226256] CR2:
0000000000000020
Fixes: 75216638572f ("RDMA/cma: Export rdma cm interface to userspace")
Reported-by: <syzbot+36712f50b0552615bf59@syzkaller.appspotmail.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Stefano Brivio [Mon, 19 Mar 2018 10:24:58 +0000 (11:24 +0100)]
ipv6: old_dport should be a __be16 in __ip6_datagram_connect()
Fixes: 2f987a76a977 ("net: ipv6: keep sk status consistent after datagram connect failure")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 20 Mar 2018 16:42:36 +0000 (12:42 -0400)]
Merge tag 'linux-can-fixes-for-4.16-
20180319' of ssh://gitolite./linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2018-03-19
this is a pull reqeust of one patch for net/master.
The patch is by Andri Yngvason and fixes a potential use-after-free bug
in the cc770 driver introduced in the previous pull-request.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
projects / openwrt / staging / blogic.git / log