rt2x00: Only register rfkill input when key is present

rt2x00 should only register the RFKILL input device when the hardware indicated
the key was present.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: move dynamic PS timeout to hardware config

This will be needed for drivers that set the
IEEE80211_HW_NO_STACK_DYNAMIC_PS flag and still
want to handle dynamic PS.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: validate SIOCSIWPOWER arguments better

Don't accept any arguments we don't handle, and return error codes
instead of using an uninitialised stack value.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: clean up channel type config

The channel_type really doesn't need to be the only member in
a new structure, so remove the struct. Additionally, remove
the _CONF_CHANGE_HT flag and use _CONF_CHANGE_CHANNEL when the
channel type changes, since that's enough of a change to require
reprogramming the hardware anyway.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

orinoco: Remove unused variable rx_data

Probably something leftover from experimentation with tasklets. Now the
structure declaration orinoco_rx_data can be relocated to orinoco.c

Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: clarify alignment docs, fix up alignment

Not all drivers are capable of passing properly aligned frames,
in particular with mesh networking no hardware will support
completely aligning it correctly.

This patch adds code to align the data payload to a 4-byte
boundary in memory for those platforms that require this, or
when CONFIG_MAC80211_DEBUG_PACKET_ALIGNMENT is set.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: remove user_power_level from driver API

I missed this during review of "mac80211: Fix tx power setting",
the user_power_level shouldn't be available to the driver but
rather be an internal value used to calculate the value for the
driver.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Minor QCU updates

* Sync qcu.c with legacy-hal
* Add some more comments
* Set QCU mask to save power (QCU mask controls which QCUs are attached
  to each DCU, we do a 1:1 mapping)

TODO: Use max QCU from EEPROM, further sync with legacy-hal and sam's
hal and a few more minor fixes.

I think after this we are ready to implement WME on the driver
part. Anyone interested ?

Signed-Off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: remove unused variable in ieee80211_local (dot11WEPUndecryptableCount).

This patch removes an unused declaration of dot11WEPUndecryptableCount
(an snmp counter) in ieee80211_local structure and its usage in
debugfs.c since this counter is not incremented/decremented anywhere.

Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: remove an unused definition (MAX_STA_COUNT) in sta_info.h.

This patch removes an unused definition of MAX_STA_COUNT in sta_info.h.

Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: remove an unused parameter in ieee80211_rx_mgmt_probe_req().

This patch removes an unused parameter (rx_status) in
ieee80211_rx_mgmt_probe_req(),
in mlme.c.

Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: remove an unnecessary assignment to info in __ieee80211_tx().

This patch removes an unnecessary assignment to info
in __ieee80211_tx() , tx.c.

Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Add 802.11h CSA support

Move to the advertised channel on reception of
a CSA element. This is needed for 802.11h compliance.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Allow to set channel in adhoc properly

The last patch fixes a bug that it was not possible to set the channel
manually in the ad hoc mode properly.

Please commit this patches so that we don't need the proprietary
Broadcom driver in the near future anymore.

Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Don't merge if BSSID is set manually

If you set a fixed BSSID manually, you never want that the driver
change it back, or your ad-hoc mesh network will break into peaces. So
don't do it.

Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Don't scan if BSSID and channel are set manually

If you set a fixed BSSID and channel it's not necessary to scan for
neighbors to merge, because you really don't want to merge with it. So
don't do it.

Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Disallow to set multicast BSSID

Okay, here is the first of the five patches. After applying all
of them you should be able to build/join huge city mesh networks
(e.g. with the OLSR protocol) with the most of the mac80211 wireless
drivers by setting a fixed BSSID in the ad hoc mode. (If you found no
other bug/problem.) This was not specified in the original standard,
but is a widely used de facto standard.

The first patch now completely disallow to set multicast MAC addresses
as BSSID. The behavior before was really strange.

Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Replace RFKILL with INPUT

As discussed on linux-wireless rt2x00 does not offer a true RFKILL key,
for that reason RFKILL support should be entirely removed.

The key which is attached to the hardware should be treated as normal
input device instead. Implement input_poll_dev support to poll the device
frequently. When the key status has changed report it as a SW event.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Enable Bluetooth Coexistence support

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: fix off-by-one in gpio checks

Sanity checks against AR5K_NUM_GPIO were all broken.  This doesn't
currently cause any problems since we only use the first four gpios.

Changes-licensed-under: ISC

Reported-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: support LEDs on Acer Aspire One netbook

Add vendor ID for Foxconn and use it to set the ath5k LED gpio and
polarity for Acer branded laptops.

base.c:
Changes-licensed-under: 3-Clause-BSD

Reported-by: Maxim Levitsky <maximlevitsky@gmail.com>
Tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Tested-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

p54: power save management

This patch implements dynamic power save feature for p54.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

p54: implement FIF_OTHER_BSS filter setting

According to STMicroelectronics' LMAC documentation, the P54_FILTER_TYPE_TRANSPARENT flag
"configures the receive frame filter to pass all frames without regard to type and address matching."

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

p54: enable rx/tx antenna diversity by eeprom bits

Respect all documented bits in the eeprom about the device diversity features.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: use signed format to print HAL status

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: clean up set_key callback

The set_key callback now seems rather odd, passing a MAC address
instead of a station struct, and a local address instead of a
vif struct. Change that.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Bob Copeland <me@bobcopeland.com> [ath5k]
Acked-by: Ivo van Doorn <ivdoorn@gmail.com> [rt2x00]
Acked-by: Christian Lamparter <chunkeey@web.de> [p54]
Tested-by: Kalle Valo <kalle.valo@nokia.com> [iwl3945]
Tested-by: Samuel Ortiz <samuel@sortiz.org> [iwl3945]
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: make wake/stop_queue_by_reason() functions static

Fixes sparse warnings:

net/mac80211/util.c:355:6: warning: symbol
  'ieee80211_wake_queue_by_reason' was not declared. Should it be static?
net/mac80211/util.c:385:6: warning: symbol
  'ieee80211_stop_queue_by_reason' was not declared. Should it be static?

Thanks to Johannes Berg for reporting this.

Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: Change schedule for old-fw support removal

The scheduled date for the removal of old fw support was in July 2008.
However, we're not going to remove the support unless it causes a major
headache. So change the schedule from "July 2008" to "when it causes headaches".

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

p54: regulatory domain hints

This patch adds a sub-routine that parses the default country eeprom entry
and forwards the obtained Alpha2 identifier to the regulatory sub-system.

Note: I dropped the p54 specific regdomain<->alpha2 conversion code for now.
But it will be added as soon as there's the common library function is ready.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

p54: prevent upload of wrong firmwares

This patch will prevent anyone to upload a firmware which was not designed for his device.

There's still a catch:
There is no easy way to detect if a firmware is for PCI or for USB (1st Gen),
because they all share the same LM86 identifier.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

p54usb: utilize usb_reset_device for 3887

Sometimes on unload or reboot the 3887 USB devices become stuck.
<usual log entry>
kernel: usbcore: registered new interface driver p54usb
kernel: usb 2-10: (p54usb) reset failed! (-110)
kernel: p54usb: probe of 2-10:1.0 failed with error -110
[...]

and a physical unplug and replug was necessary.
However we should be able to do this in software as well,
without any user interaction.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43/ssb: Add SPROM8 extraction and LP-PHY detection

This adds detection code for the LP-PHY and SPROM
extraction code for version 8, which is needed by the LP-PHY and
newer N-PHY.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: detect N PHY revision/radio

Does nothing unless you enable the hidden N PHY config.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: INI update for Atheros AR9280 and AR9285 chipset.

Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ssb/b43: add new N PHY device

This is used on my macbook. N PHY, obviously nothing works
yet, but we can detect the chip with this patch.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Fix tx power setting

power_level in ieee80211_conf is being used for more than one
purpose. It being used as user configured power limit and the
final power limit given to the driver. By doing so, except very
first time, the tx power limit is taken from min(chan->max_power,
local->hw.conf.power_level) which is not what we want. This patch
defines a new memeber in ieee80211_conf which is meant only for
user configured power limit.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix sparse warnings

Fix sparse warnings:

drivers/net/wireless/ath9k/hw.c:1850:17: warning: symbol 'tmp' shadows an earlier one
drivers/net/wireless/ath9k/hw.c:1713:6: originally declared here
drivers/net/wireless/ath9k/hw.c:2051:17: warning: symbol 'tmp' shadows an earlier one
drivers/net/wireless/ath9k/hw.c:1961:6: originally declared here

drivers/net/wireless/ath9k/eeprom.c:195:6: warning: symbol 'ath9k_fill_eeprom' was not declared. Should it be static?
drivers/net/wireless/ath9k/eeprom.c:463:5: warning: symbol 'ath9k_check_eeprom' was not declared. Should it be static?
drivers/net/wireless/ath9k/eeprom.c:1219:6: warning: symbol 'ath9k_hw_set_def_power_per_rate_table' was not declared. Should it be static?
drivers/net/wireless/ath9k/eeprom.c:1510:6: warning: symbol 'ath9k_hw_set_4k_power_per_rate_table' was not declared. Should it be static?
drivers/net/wireless/ath9k/eeprom.c:2007:5: warning: symbol 'ath9k_set_txpower' was not declared. Should it be static?
drivers/net/wireless/ath9k/eeprom.c:2106:6: warning: symbol 'ath9k_set_addac' was not declared. Should it be static?
drivers/net/wireless/ath9k/eeprom.c:2543:6: warning: symbol 'ath9k_eeprom_set_board_values' was not declared. Should it be static?
drivers/net/wireless/ath9k/eeprom.c:2606:5: warning: symbol 'ath9k_get_eeprom_antenna_cfg' was not declared. Should it be static?
drivers/net/wireless/ath9k/eeprom.c:2622:4: warning: symbol 'ath9k_hw_get_4k_num_ant_config' was not declared. Should it be static?
drivers/net/wireless/ath9k/eeprom.c:2628:4: warning: symbol 'ath9k_hw_get_def_num_ant_config' was not declared. Should it be static?
drivers/net/wireless/ath9k/eeprom.c:2647:4: warning: symbol 'ath9k_get_num_ant_config' was not declared. Should it be static?
drivers/net/wireless/ath9k/eeprom.c:2790:5: warning: symbol 'ath9k_get_eeprom' was not declared. Should it be static?

drivers/net/wireless/ath9k/calib.c:962:30: warning: symbol 'iq_cal_multi_sample' was not declared. Should it be static?
drivers/net/wireless/ath9k/calib.c:969:30: warning: symbol 'iq_cal_single_sample' was not declared. Should it be static?
drivers/net/wireless/ath9k/calib.c:976:30: warning: symbol 'adc_gain_cal_multi_sample' was not declared. Should it be static?
drivers/net/wireless/ath9k/calib.c:983:30: warning: symbol 'adc_gain_cal_single_sample' was not declared. Should it be static?
drivers/net/wireless/ath9k/calib.c:990:30: warning: symbol 'adc_dc_cal_multi_sample' was not declared. Should it be static?
drivers/net/wireless/ath9k/calib.c:997:30: warning: symbol 'adc_dc_cal_single_sample' was not declared. Should it be static?
drivers/net/wireless/ath9k/calib.c:1004:30: warning: symbol 'adc_init_dc_cal' was not declared. Should it be static?

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: remove superfluous check on changing channel

When we try to change the channel in ath9k its because
either the configuration indicates we *have* changed
channels or HT configuration has changed. In both cases
we want to do a reset. Either way mac80211 will inform us
when we want to actually change the channel so trust those
calls.

Although in the patch it may seem as I am doing more code
changes I am not, all I am doing is removing the initial
branch conditional and shifting the code to the left.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: remove ath9k_hw_check_chan()

The only check we care about in ath9k_hw_check_chan() is
the internal regulatory check so use that.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: remove ath9k_hw_chan2wmode()

The only left users are for timing for ACK timeout, slotime and
CTS timeout. We currently use an array CLOCK_RATE to keep
these values per mode and since as only will use A and G
we can depend on the band to get the appropriate values.

We note that we should be using a different clock rate value
for CCK, we can do this in separate patch, currently this is
being disregarded and should only affect when we want to
change the default ACK/CTS timeout or slot time and stuck
with using using 802.11b.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: remove mode specific default noise floor values

The NOISE_FLOOR array we have is mode specific, and the only
possible indexed values are A, B and G. The mode routine only
can return G or A, so this is band specific. Then since the
values for A and G (5ghz or 2ghz) are the same (-96) we simply
remove the array and use a static value.

If we later determine we want to use special values for
HT configurations we can use the new mac80211 conf_is_ht*()
helpers.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Make ANI CCK and OFDM error triggers band specific

The CCK and OFDM ANI error triggers are not mode specific but rather
band specific so just make use of the already available band from
ieee80211_conf.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: no need for ht.enabled

We can simply use conf_is_ht() check where needed.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: make use of conf_is_ht*() helpers

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: make use of conf_is_ht*() in the rest of the driver

Use shiny new conf_is_ht*() helpers, we can later remove ht.enabled if
desired.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: use ieee80211_conf on ath9k_hw_iscal_supported()

ath9k_hw_iscal_supported() just needs to be aware of your band
and if HT20 is being used so lets abandon our internal channel,
HT appended values and internal mode values and use ieee80211_conf
which already carries this information. This works as calibration
is being done for the currently configured channel.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: make request to get the noisefloor threshold band specific

Lets make the request to get the current noise floor threshold
from the EEPROM band specific as it is band specific, not mode
specific.

This also adds a backpointer on the private channel structure
back to the ieee80211_channel structure as this is now needed during
ath9k_hw_getnf().

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: consolidate arguments on hw reset

HW reset calls pass the same variables or structs
which we can obtain easily from ah. Although this also applies
during channel changes as we will keep around the ath9k_channel
passed as an argument for now.

We now also now propagate the hw reset errors down.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Rename ath_setcurmode() to ath_cache_conf_rate()

ath_setcurmode() is a bit misleading, all we are doing is
caching the rate for the corresponding configuration we
are using.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: remove cache of rate preference when using 11g protection

No need to cache when we want to use 2Mbit/s for all protection
frames for 802.11g as we can determine that dynamically on
ath_buf_set_rate() itself.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: use hw->conf on ath_setcurmode()

We don't need to use our own mode for setting the
the routine tries to do, in fact lets remove ath_chan2mode() now as
we can simply use the currently set band and the HT configuration
provided by mac80211 through the ieee80211_conf. This works on
changing channels as well as the internal ath9k_channel we use is
based on the ieee80211_channel in the config.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: add HT conf helpers

In HT capable drivers you often need to check if you
are currently using HT20 or HT40. This adds a few small
helpers to let drivers figure that out.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: use rx queue management infrastructure from iwlcore

This patch uses rx queue alloc free and reset function from iwlcore.
This should fix the regression reported by Kalle Valo.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: use iwl3945_tx_cmd instead of iwl_tx_cmd

The patch replaces iwl_tx_cmd with iwl3945_tx_cmd to complete
transitions introduced by "iwlwifi: use iwl_cmd instead
of iwl3945_cmd"

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: switch to the iwl-core send_card_state routine

Switch iwl3945 to use iwl-core:send_card_state routine.

Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: sync tx queue data structure with iwlagn

We are now using the iwl_tx_queue for iwl3945. To reach that goal, we
included the 3945 specific tfd frame structure to iwl_tx_queue. This
has no effect on the current iwlagn code.

Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: adding utils ops

The patch implements iwl_hcmd_utils_ops for 3945.

Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: rearrange 3945 tfd

This patch moves 3945 TFD structures to iwl-3945-fh.h. It renames them
similarly to AGN naming. This patch also eliminates iwl3945_tx_info and
fixes endianity issue in iwl3945_tx_skb and iwl3945_enqueue_hcmd caused
by ugly casting.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: use iwl_rb_status

This patch makes use of iwl_rb_status also in 3945. The structure
for 3945 is not the same but since only closed_rb_num filed is used
in both cases there is no reason to duplicate it.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: use iwl_get_hw_mode

Use iwl_get_hw_mode for 3945.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: release resources before shutting down

Release resource before shutting down and notify upper stack.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: simplify iwl3945_pci_probe

The patch simplifies iwl3945_pci_probe. It also uses apm_ops for apm init.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: add set_pwr_src

The patch adds 3945 iwl_lib_ops->set_pwr_src to the driver

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: add apm ops

The patch adds 3945 iwl_lib_ops->apm_ops to the driver.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: add load ucode op

The patch adds 3945 iwl_lib_ops->load_ucode to the driver.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: cleanup and remove duplicate code

The patch removes the following duplicate structures:

iwl3945_is_alive
iwl3945_is_ready
iwl3945_is_init
iwl3945_is_rfkill_sw
iwl3945_is_rfkill
iwl3945_reset_qos

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: use iwl_mod_params for 3945

Use iwl_mod_params for 3945.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: use iwl_cmd instead of iwl3945_cmd

This patch makes use of iwl_cmd instead of iwl3945_cmd and related
structures which were just the same.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: replace IWL_ERROR with IWL_ERR

IWL_ERR doesn't use hidden priv pointer.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: replace IWL_WARNING with IWL_WARN

IWL_WARN doesn't use hidden priv pointer.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: clean up printing

Use IWL_ macros where possible to unify debug output usage.
Define new unconditional printouts IWL_ERR, IWL_WARN, IWL_INFO,
and IWL_CRIT which don't use hidden priv pointer.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: add more comments to IWL_DL_xx

This adds more comments to IWL_DL_xx macros.

Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: use iwl-io.h and delete iwl-3945-io.h

The patch deletes iwl-3945-io.h and uses iwl-io.h functions.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: replaces iwl3945_priv with iwl_priv

The patch replaces iwl3945_priv to iwl_priv. It adds 3945 specific
data members to iwl_priv.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: rename iwl3945_priv variables

The patch renames iwl3945 specific variables in iwl3945_priv
structure. iwl3945_priv structure differs with iwl_priv structure
with these variables. Goal of this patch is to make transition from
iwl3945_priv to iwl_priv smoothly.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: use iwl_hw_params in iwl3945_priv

The patch makes changed necessary to use iwl_hw_params to
replace iwl3945_driver_hw_info.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: use iwl_rx_queue in iwl3945

The patch replaces iwl3945_rx_queue with iwl_rx_queue.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: use iwl_rx_mem_buffer

The patch replaces iwl3945_rx_mem_buffer with iwl_rx_mem_buffer.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: beautify code

This patch beautifies macros in iwl-debug.h.

Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: replace iwl3945_broadcast_addr with iwl_bcast_addr

The patch replaces iwl3945_broadcast_addr with iwl_bcast_addr for 3945.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: remove duplicate structures from iwl-3945.h

The patch renames and deletes duplicate structure from iwl-3945.h.
The following structures are renamed with iwlwifi counterparts:

1) iwl3945_ac_qos
2) iwl3945_ucode
3) iwl3945_qos_capabity

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: move structures from iwl-3945.h to iwl-dev.h

The patch moves few structres from iwl-3945.h to iwl-dev.h.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: replace iwl_3945_cfg with iwl_cfg

The patch replaces iwl_3945_cfg with iwl_cfg for 3945.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: include iwl-core.h

Use iwl-core.h instead of iwl-3945-core.h.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: Change IWLWIFI_VERSION constant name

Change IWLWIFI_VERSION to IWL3945_VERSION.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: emliminate iwl3945_mac_get_stats mac80211 handler

This patch removes empty iwl3945_mac_get_stats mac80211 handler.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: iwl3945_queue and iwl3945_channel_info replacement

This patch replaces the queue and channel info 3945 structures with the iwl
ones.

The initial goal was to replace the channel info structure. Once we do that,
and then include iwl-dev.h instead of iwl-3945.h, we still get build errors
due to several routines and macro redefinitions. This is why this patch also
includes:
- TFD39_MAX_PAYLOAD definition for 3945.
- CMD_SIZE, CMD_HUGE, CMD_SKB duplication removal.
- iwl3945_queue replacement in order to also get rid of the duplicated
get_cmd_index routine.

Getting rid of any of those needs the iwl-dev.h inclusion which then creates
build errors due to definitions duplication. This is why we include all those
in the same patch.

Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: Remove power related definitions from 3945 code

Most of the power (not TX power, but power management) structures and
definitions are duplicated accross iwl-power.h and iwl-3945.h. We should try
to only use the iwl header.

Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Acked-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: Getting rid of iwl-3945-led.h

The duplicated LED definitions prevent one from including iwl-dev.h from the
3945 specific C files.
Moreover, we are sharing many definitions between iwl-3945-led.h and
iwl-led.h, so let's just use the iwl one. Note that this file will get more
cleanups once we share a common iwl_priv structure.

Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Acked-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: Use iwl-agn-rs.h rates definitions.

A lot of rate relates definition are shared between iwl-3945-rs.h and
iwl-agn-rs.h. Let's just use the agn version, and add the 3945 specific
constants there.

Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: Have consistant and not redefined HW constants

SRAM addresses are different for 3945, 4065, and 5000, let's give them
different names.
Also, the RSSI_OFFSET is different for 3945 and 4965, thus they should be
named differently.

Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: Getting rid of iwl3945_eeprom_channel

The corresponding iwl structure is identical.

Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: Remove DRV_NAME dependenies

As DRV_NAME is defined in 2 different header files, including both is not
possible.
This patch defines this constant from iwl3945-base.c and iwl-agn.c. It also
redefines the IWL_ERROR and IWL_WARNING macros to use dev_printk, as the
IWL_DEBUG_* macros do.

Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Acked-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: Getting rid of iwl-3945-debug.h

At the cost of adding a debug_level field to iwl3945_priv, we are now able to
get rid of iwl-3945-debug.h, and use iwl-debug.h instead.

Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: 3945 remove iwl-3945-commands.h

This patch remove iwl-3945-commands.h
eliminating duplicated and moving all definitions to iwl-commands.h

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: 3945 drop usage of union tsf

This patch replaces union tsf with u64
This also allows to use iwl_error_res
and iwl_rxon_time_cmd instead of 3945 structures

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: 3945 remove duplicated code from iwl-3945-commands.h

This patch remove trivial (renames) commands and defines
from iwl-3945-commands.h

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: use iwl-commands.h also in 3945

This patch uses iwl-commands.h also for iwl3945
more clean ups are required but this get to stage where it
compiles cleanly.
Most massive changes are in spectrum and power managment.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: 3945 remove current_rate from station entry.

This patch removes current_rate from station_entry it was write only
variable

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: 3945 unfold iwl-3945-commands.h

This patch unfolds includes of iwl-3945-commands.h

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>