Pawel Dembicki [Fri, 22 Apr 2022 07:24:34 +0000 (09:24 +0200)]
generic: 5.15: add missing symbol
Found durring kirkwood refreshing.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Pawel Dembicki [Fri, 22 Apr 2022 07:05:52 +0000 (09:05 +0200)]
kirkwood: copy config and patches to 5.15
This patch makes only a copy of 5.10 config and patches.
Patches merged in upstream was omited.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Sungbo Eo [Sat, 30 Apr 2022 17:14:23 +0000 (02:14 +0900)]
ipq40xx: 5.15: refresh subtarget config
Update config with `make kernel_oldconfig CONFIG_TARGET=subtarget`.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Robert Marko [Mon, 25 Apr 2022 11:10:15 +0000 (13:10 +0200)]
ipq40xx: 5.15: refresh config
Refresh 5.15 kernel config for IPQ40xx due to large number of generic
config changes.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Robert Marko [Mon, 25 Apr 2022 11:09:18 +0000 (13:09 +0200)]
ipq40xx: 5.15: drop upstreamed sleep clock patch
Patch that corrects sleep clock frequency has already been backported
to 5.15 stable so remove the duplicate patch.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Ansuel Smith [Mon, 28 Mar 2022 00:55:40 +0000 (02:55 +0200)]
ipq40xx: 5.15: add testing kernel version
Add 5.15 kernel as a testing kernel version in the Makefile.
Linksys EA6350v3/EA8300/MR8300 will not build with buildbot settings and
should be disabled when the target is switched, unless the image size is
reduced again.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Robert Marko <robert.marko@sartura.hr>
[add comment for increased kernel size]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Ansuel Smith [Sun, 27 Mar 2022 22:12:55 +0000 (00:12 +0200)]
ipq40xx: 5.15: refresh kernel patches
Refresh kernel patches.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Robert Marko <robert.marko@sartura.hr>
Ansuel Smith [Sat, 20 Nov 2021 22:10:20 +0000 (23:10 +0100)]
ipq40xx: refresh ess driver and phy with new api
Kernel 5.15 have some new api for ethtool and phy.
Add ifdef to fix compilation error.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Robert Marko <robert.marko@sartura.hr>
Ansuel Smith [Sat, 20 Nov 2021 22:08:25 +0000 (23:08 +0100)]
ipq40xx: fix wrong nand definition for wpj419
Fix wrong nand definition for wpj419 that differ from the upstream
node name.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Ansuel Smith [Sat, 20 Nov 2021 22:07:21 +0000 (23:07 +0100)]
ipq40xx: 5:15: refresh config
Refresh config for kernel 5.15 using make kernel_menuconfig
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Ansuel Smith [Sat, 20 Nov 2021 22:06:34 +0000 (23:06 +0100)]
ipq40xx: 5:15: refresh patches
- Drop upstream patch
- Refresh dts patch
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Ansuel Smith [Sat, 20 Nov 2021 22:05:02 +0000 (23:05 +0100)]
ipq40xx: 5:15: copy config and patch from 5.10
Copy config and patch from 5.10 to 5.15
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Alban Bedel [Sat, 23 Apr 2022 09:28:51 +0000 (11:28 +0200)]
ramips: zbt-wg2626: Fix the LAN ports names
The current names don't match with the labels on the case, reverse
the LAN ports order so they match.
Signed-off-by: Alban Bedel <albeu@free.fr>
Alban Bedel [Sat, 30 Apr 2022 08:42:33 +0000 (10:42 +0200)]
ramips: zbt-wg2626: Add the reset gpio for PCIe port 1
The 2.4GHz interface doesn't come up properly with the log showing:
mt7621-pci
1e140000.pcie: pcie1 no card, disable it (RST & CLK)
As seen on other MT7621 boards this is caused by a missing reset GPIO.
The MT7621 dtsi set GPIO 19 as PCIe reset GPIO, which on this board
reset the 5GHz interface on port 0. Add GPIO 8 to the PCIe reset GPIO
list to also reset the 2.4GHz interface on port 1.
Signed-off-by: Alban Bedel <albeu@free.fr>
Nick Hainke [Sun, 10 Apr 2022 07:00:59 +0000 (09:00 +0200)]
mdadm: update to 4.2
Refreshed patches:
- 100-cross_compile.patch
Manually refreshed patches:
- 200-reduce_size.patch
Removed patches:
- 101-mdadm.h-Undefine-dprintf-before-redefining.patch
- 102-Add-missing-include-file-sys-sysmacros.h.patch
Changes:
e30ca260 Release mdadm-4.2
8c80d305 Monitor: print message before quit for no array to monitor
ced5fa8b mdadm: block creation with long names
b71de056 Correct checking if file descriptors are valid
b2e4f084 Incremental: Close unclosed mdfd in IncrementalScan()
195d1d76 imsm: assert if there is migration but prev_map doesn't exist
75f3ba25 imsm: free allocated memory in imsm_fix_size_mismatch
bce0eab3 Release mdadm-4.2-rc3
4389ce73 imsm: introduce helpers to manage file descriptors
8e1a258e mdadm/Detail: Can't show container name correctly when unpluging disks
a35aa68f mdadm/lib: Define a new helper function is_dev_alived
1c66260d Fix 2 dc stream buffer
d64a37b9 Assemble: apply sysfs rules
5f6dedfb Fix potential overlap dest buffer
a0422106 disallow create or grow clustered bitmap with writemostly set
cf16a350 Fix buffer size warning for strcpy
60815698 Refactor parse_num and use it to parse optarg.
f7889e51 Fix error message when creating raid 4, 5 and 10
54604768 mdadm: fix coredump of mdadm --monitor -r
feeb2785 Utils: Change sprintf to snprintf
b8bbf264 Release mdadm-4.2-rc2
e6878148 Assemble: skip devices that don't match uuid instead of aborting the assembly.
0663137c Add monitor delay parameter to mdadm.conf
2b2c5668 tests: Avoid passing chunk size when creating RAID 1
7d374a18 Fix memory leak after "mdadm --detail"
92a647c8 Assemble: start dirty and degraded array.
1c275381 imsm: fix num_data_stripes after raid0 takeover
5b30a34a Add error handling for chunk size in RAID1
3a85bf0e imsm: Fix possible memory leaks and refactor freeing struct dl
ccd61ebf mdadm: Fix building errors
601ffa78 Don't associate spares with other arrays during RAID Examine
8d69bf14 Remove Spare drives line from details for external metadata
7d8935cb imsm: correct offset for 4k disks in --examine output
dca80fcd Use dev_open in validate geometry container
f421731c mdadm/super1: It needs to specify int32 for bitmap_offset
1f5d54a0 Manage: Call validate_geometry when adding drive to external container
8662f92d imsm: Limit support to the lowest namespace
fcebeb77 imsm: add devpath_to_char method
7c798f87 imsm: add generic method to resolve "device" links
0530e2e0 Prevent user from using --stop with ambiguous args
83b3de77 Fix some building errors
ff904202 imsm: change wrong size verification
c11b1c3c Release mdadm-4.2-rc1
aec01630 super-intel.c: Handle errors from calls to get_dev_sector_size()
78c93b00 mdadm: fix growing containers
af3396da Monitor: make libudev dependency optional
f94df5cf imsm: support for third Sata controller
d835518b imsm: nvme multipath support
4036e7ee imsm: extend curr_migr_unit to u64
bdbe7f81 Grow: Block reshape when external metadata and write-intent bitmap
848d71c9 Create: Block automatic enabling bitmap for external metadata
19ad203e imsm: Update-subarray for write-intent bitmap
dc95f821 Add "bitmap" to allowed command-line values
69d40de4 imsm: Adding a spare to an existing array with bitmap
fbc42556 imsm: Write-intent bitmap support
b554ab5c Enable bitmap support for external metadata
b090e910 Modify mdstat parsing for volumes with the bitmap
db537788 It should be FAILED when raid has not enough active disks
c7b8547c imsm: add verbose flag to compare_super
49b69533 mdmonitor: check if udev has finished events processing
0d583954 Document PPL in man md
2f86fda3 imsm: use saved fds during migration
f7a6246b super1.c: avoid useless sync when bitmap switches from clustered to none
e6561c4d super1: fix Floating point exception
8818d4e7 Grow: be careful of corrupt dev_roles list
4ae96c80 mdadm: fix reshape from RAID5 to RAID6 with backup file
1fe2e100 mdadm/bitmap: locate bitmap calcuate bitmap position wrongly
75562b57 Dump: get stat from a wrong metadata file when restoring metadata
69068584 Incremental: Remove redundant spare movement logic
a64f1263 udev: start grow service automatically
b4a5ad49 Make target to install binaries only
9c030dad mdadm/Detail: show correct state for clustered array
ff6bb131 mdadm: Unify forks behaviour
a8f3cfd5 imsm: limit support to first NVMe namespace
ca4b156b Monitor: don't use default modes when creating a file
b65c1f4a imsm: remove redundant calls to imsm_get_map
895ffd99 imsm: update num_data_stripes according to dev_size
ce559078 Create.c: close mdfd and generate uevent
c3129b39 Detail: fix segfault during IMSM raid creation
97b51a2c Super1: allow RAID0 layout setting to be removed.
7f3b2d1d Check if other Monitor instance running before fork.
cab9c67d mdmonitor: set small delay once
007087d0 Monitor: stop notifing about containers.
e2308733 Monitor: refresh mdstat fd after select
2ce09172 Don't create bitmap for raid5 with journal disk
64bf4dff Detail: show correct raid level when the array is inactive
5f418455 manual: update --examine-badblocks
5e592e1e mdadm/md.4: update path to in-kernel-tree documentation
138a9e9b Specify nodes number when updating cluster nodes
77b72fa8 mdadm/Grow: prevent md's fd from being occupied during delayed time
bcf40dbb Update link to Intel page for IMSM
8e41153c Use more secure HTTPS URLs
2cf04330 Detect too-small device: error rather than underflow/crash
7758ada9 Block overwriting existing links while manual assembly
d92cee7b restripe: fix ignoring return value of ‘read’ and lseek
7d90f760 Include count for \0 character when using strncpy to implement strdup.
f4c8a605 uuid.c: split uuid stuffs from util.c
03ab9763 Makefile: add EXTRAVERSION support
3b7aae92 mdcheck: Log when done
7b99edab Assemble.c: respect force flag.
ec7d7cee clean up meaning of small typo
5cfb79de Assemble: print error message if mdadm fails assembling with --uuid option
12724c01 Manage, imsm: Write metadata before add
1c294b5d Detail: adding sync status for cluster device
185ec439 Monitor: improve check_one_sharer() for checking duplicated process
e1b92ee0 udev: Ignore change event for imsm
ba1b3bc8 imsm: show Subarray and Volume ID in --examine output
e48aed3c imsm: support the Array Creation Time field in metadata
9e449405 Detail: show correct bitmap info for cluster raid device
06a6101c imsm: Correct minimal device size.
45c43276 imsm: Remove --dump/--restore implementation
3364781b imsm: pass subarray id to kill_subarray function
fd38b8ea Remove the legacy whitespace
2551061c mdadm.8: add note information for raid0 growing operation
1e93d0d1 imsm: fill working_disks according to metadata.
42e641ab Add support for Tebibytes
4431efeb imsm: Update grow manual.
e1512e7b mdcheck service can't start succesfully because of syntax error
1a874930 Change warning message
aced6fc9 Respect $(CROSS_COMPILE) when $(CC) is the default
027c099f Assemble: add support for RAID0 layouts.
329dfc28 Create: add support for RAID0 layouts.
6da53c0e imsm: Change the way of printing nvme drives in detail-platform.
b771faef imsm: return correct uuid for volume in detail
4b31846f Remove unused code
9cf361f8 Fix up a few formatting issues
02af3793 Remove last traces of HOT_ADD_DISK
1cc3965d Manage: Remove the legacy code for md driver prior to 0.90.03
761e3bd9 super-intel: don't mark structs 'packed' unnecessarily
85b83a79 SUSE-mdadm_env.sh: handle MDADM_CHECK_DURATION
4ca799c5 mdcheck: use ${} to pass variable to mdcheck
6636788a mdcheck: when mdcheck_start is enabled, enable mdcheck_continue too.
1a1ced1e imsm: allow to specify second volume size
b6180160 imsm: save current_vol number
7bd59e79 udev: allow for udev attribute reading bug.
61109314 Don't need to check recovery after re-add when no I/O writes to raid
8063fd0f Init devlist as an array
e53cb968 mdadm/md.4: add the descriptions for bitmap sysfs nodes
2c2d9c48 mdadm: force a uuid swap on big endian
43ebc910 mdadm: Introduce new array state 'broken' for raid0/linear
fd5b09c9 mdadm: check value returned by snprintf against errors
91c97c54 imsm: close removed drive fd.
1a52f1fc udev: add --no-devices option for calling 'mdadm --detail'
d11abe4b mdadm: add --no-devices to avoid component devices detail information
452dc4d1 mdadm.h: include sysmacros.h unconditionally
b0681598 mdadm: load default sysfs attributes after assemblation
486720e0 super-intel: Use put_unaligned in split_ull
7039d1f8 mdadm.h: Introduced unaligned {get,put}_unaligned{16,32}()
a4f7290c super-intel: Fix issue with abs() being irrelevant
4ec389e3 Enable probe_roms to scan more than 6 roms.
ae7d61e3 mdmon: fix wrong array state when disk fails during mdmon startup
3c9b46cf udev: Add udev rules to create by-partuuid for md device
22dc741f Create: Block rounding size to max
05501181 imsm: fix spare activation for old matrix arrays
227aeaa8 add missing units to --examine
2b57e4fe Assemble: Fix starting array with initial reshape checkpoint
d2e11da4 mdmon: wait for previous mdmon to exit during takeover
69d08478 mdmon: don't attempt to manage new arrays when terminating
76b906d2 mdadm/tests: add one test case for failfast of raid1
cab114c5 Fix reshape for decreasing data offset
e3615ecb Detail.c: do not skip first character when calling xstrdup in Detail()
ebf3be99 Fix spelling typos.
9f421827 imsm: fix reshape for >2TB drives
a4e96fd8 imsm: finish recovery when drive with rebuild fails
757e5543 policy.c: Fix for compiler error
467e6a1b policy.c: prevent NULL pointer referencing
76d505de Grow: report correct new chunk size.
085df422 Grow: avoid overflow in compute_backup_blocks()
563ac108 Assemble: mask FAILFAST and WRITEMOSTLY flags when finding the most recent device
d7a1fda2 imsm: update metadata correctly while raid10 double degradation
7cd7e91a Monitor: add system timer to run --oneshot periodically
4199d3c6 mdcheck: add systemd unit files to run mdcheck.
cd72f9d1 policy: support devices with multiple paths.
6b611284 Document PART-POLICY lines
0833f9c3 Assemble: keep MD_DISK_FAILFAST and MD_DISK_WRITEMOSTLY flag
Signed-off-by: Nick Hainke <vincent@systemli.org>
Kerma Gérald [Thu, 28 Apr 2022 22:08:09 +0000 (00:08 +0200)]
f2fs-tools: fix resize.f2fs (#9800)
resolve issue
- https://github.com/openwrt/openwrt/issues/9800
add the upstream patch:
- f2fs-tools.git/patch/?id=
f056fbeff08d30a6d9acdb9e06704461ceee3500
Signed-off-by: Kerma Gérald <gandalf@gk2.net>
Josef Schlehofer [Thu, 28 Apr 2022 11:34:35 +0000 (13:34 +0200)]
uboot-mvebu: update to version v2022.04
Release announcement:
https://lore.kernel.org/u-boot/
20220404143253.GQ14476@bill-the-cat/
Release notes between tags:
https://source.denx.de/u-boot/u-boot/-/compare/v2022.01...v2022.04?from_project_id=531
All patches were removed, since they are included in this release.
Run tested: Turris Omnia, mvebu/cortex-a9, OpenWrt daily snapshots
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Josef Schlehofer [Thu, 28 Apr 2022 13:50:20 +0000 (15:50 +0200)]
uboot-mvebu: remove enabled CONFIG_CMD_SETEXPR
We don't need to make sure that we want to have enabled
CONFIG_CMD_SETEXPR by default, since this is already done in U-boot [1].
This was actually needed only for clearfog board [2], which was added in
commit:
da0005a6d08ae33d958a6d8a6c0c12dc07b5b2b8 ("uboot-mvebu: add
patch to enable setexpr for clearfog boards) and send to U-boot to fix
it properly. After a while, there was added support for Turris Omnia,
which uses setexpr as well [3], but for this board, there are no fixes
needed in U-boot and that's why we can remove this option here.
It is helpful with shell scripting. If some downstream distributions are
using it, they should correct it in defconfig for related boards.
[1] https://source.denx.de/u-boot/u-boot/-/blob/
e95afa56753cebcd20a5114b6d121f281b789006/cmd/Kconfig#L1504
[2] https://github.com/openwrt/openwrt/blob/
852126680e21edc71c0c66561ae5a6d7479dcc67/target/linux/mvebu/image/clearfog.bootscript#L7
[3] https://github.com/openwrt/openwrt/blob/
852126680e21edc71c0c66561ae5a6d7479dcc67/target/linux/mvebu/image/turris-omnia.bootscript#L2
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Josef Schlehofer [Fri, 29 Apr 2022 15:52:29 +0000 (17:52 +0200)]
uboot-mvebu: add patch to enable setexpr for clearfog boards
Option CMD_SETEXPR is already default in U-boot [1], since this was
disabled since initial version for this board, there is send this
patch to U-boot mailing list to enable it.
It is required to use in OpenWrt bootscript for these boards [2].
[1] https://source.denx.de/u-boot/u-boot/-/blob/
e95afa56753cebcd20a5114b6d121f281b789006/cmd/Kconfig#L1504
[2] https://github.com/openwrt/openwrt/blob/
852126680e21edc71c0c66561ae5a6d7479dcc67/target/linux/mvebu/image/clearfog.bootscript#L7
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Nick Hainke [Sun, 20 Mar 2022 16:57:22 +0000 (17:57 +0100)]
ath79: add Netgear WNDAP360
SoC: Atheros AR7161
RAM: DDR 128 MiB (hynix h5dU5162ETR-E3C)
Flash: SPI-NOR 8 MiB (mx25l6406em2i-12g)
WLAN: 2.4/5 GHz
2.4 GHz: Atheros AR9220
5 GHz: Atheros AR9223
Ethernet: 4x 10/100/1000 Mbps (Atheros AR8021)
LEDs/Keys: 2/2 (Internet + System LED, Mesh button + Reset pin)
UART: RJ45 9600,8N1
Power: 12 VDC, 1.0 A
Installation instruction:
0. Make sure you have latest original firmware (3.7.11.4)
1. Connect to the Serial Port with a Serial Cable RJ45 to DB9/RS232
(9600,8N1)
screen /dev/ttyUSB0 9600,cs8,-parenb,-cstopb,-hupcl,-crtscts,clocal
2. Configure your IP-Address to 192.168.1.42
3. When device boots hit spacebar
3. Configure the device for tftpboot
setenv ipaddr 192.168.1.1
setenv serverip 192.168.1.42
saveenv
4. Reset the device
reset
5. Hit again the spacebar
6. Now load the image via tftp:
tftpboot 0x81000000 INITRAMFS.bin
7. Boot the image:
bootm 0x81000000
8. Copy the squashfs-image to the device.
9. Do a sysupgrade.
https://openwrt.org/toh/netgear/wndap360
The device should be converted from kmod-owl-loader to nvmem-cells in the
future. Nvmem cells were not working. Maybe ATH9K_PCI_NO_EEPROM is missing.
That is why this commit is still using kmod-owl-loader. In the future
the device tree may look like this:
&ath9k0 {
nvmem-cells = <&macaddr_art_120c>, <&cal_art_1000>;
nvmem-cell-names = "mac-address", "calibration";
};
&ath9k1 {
nvmem-cells = <&macaddr_art_520c>, <&cal_art_5000>;
nvmem-cell-names = "mac-address", "calibration";
};
&art {
...
cal_art_1000: cal@1000 {
reg = <0x1000 0xeb8>;
};
cal_art_5000: cal@5000 {
reg = <0x5000 0xeb8>;
};
};
Signed-off-by: Nick Hainke <vincent@systemli.org>
PtilopsisLeucotis [Sat, 16 Apr 2022 10:21:58 +0000 (13:21 +0300)]
ath79: add USB power control for GL-AR300M series
Add USB power control in DTS for GL.iNet models:
- AR300M;
- AR300M-Ext;
- AR300M16;
- AR300M16-Ext.
Signed-off-by: PtilopsisLeucotis <PtilopsisLeucotis@yandex.com>
Foica David [Thu, 21 Apr 2022 01:20:57 +0000 (04:20 +0300)]
ath79: add support for TP-Link Deco M4R v1 and v2
This commit adds support for the TP-Link Deco M4R (it can also be M4,
TP-Link uses both names) v1 and v2. It is similar hardware-wise to the
Archer C6 v2. Software-wise it is very different. V2 has a bit different
layout from V1 but the chips are the same and the OEM firmware is the same
for both versions.
Specifications:
SoC: QCA9563-AL3A
RAM: Zentel A3R1GE40JBF
Wireless 2.4GHz: QCA9563-AL3A (main SoC)
Wireless 5GHz: QCA9886
Ethernet Switch: QCA8337N-AL3C
Flash: 16 MB SPI NOR
Flashing:
The device's bootloader only accepts images that are signed using
TP-Link's RSA key, therefore this way of flashing is not possible. The
device has a web GUI that should be accessible after setting up the device
using the app (it requires the app to set it up first because the web GUI
asks for the TP-Link account password) but for unknown reasons, the web
GUI also refuses custom images.
There is a debug firmware image that has been shared on the device's
OpenWrt forum thread that has telnet unlocked, which the bootloader will
accept because it is signed. It can be used to transfer an OpenWrt image
file over to the device and then be used with mtd to flash the device.
Pre-requisites:
- Debug firmware.
- A way of transferring the file to the router, you can use an FTP server
as an example.
- Set a static IP of 192.168.0.2/255.255.255.0 on your computer.
- OpenWrt image.
Installation:
- Unplug your router and turn it upside down. Using a long and thin object
like a SIM unlock tool, press and hold the reset button on the router and
replug it. Keep holding it until the LED flashes yellow.
- Open 192.168.0.1. You should see the bootloader recovery's webpage.
Choose the debug firmware that you downloaded and flash it. Wait until the
router reboots (at this stage you can remove the static IP).
- Open a terminal window and connect to the router via telnet (the primary
router should have a 192.168.0.1 IP address, secondary routers are
different).
- Transfer the file over to the router, you can use curl to download it
from the internet (use the insecure flag and make sure your source accepts
insecure downloads) or from an FTP server.
- The router's default mtd partition scheme has kernel and rootfs
separated. We can use dd to split the OpenWrt image file and flash it with
mtd:
dd if=openwrt.bin of=kernel.bin skip=0 count=8192 bs=256
dd if=openwrt.bin of=rootfs.bin skip=8192 bs=256
- Once the images are ready, you have to flash the device using mtd
(make sure to flash the correct partitions or you may be left with a
hard bricked router):
mtd write kernel.bin kernel
mtd write rootfs.bin rootfs
- Flashing is done, reboot the device now.
Signed-off-by: Foica David <superh552@gmail.com>
Davide Fioravanti [Mon, 18 Apr 2022 15:35:33 +0000 (17:35 +0200)]
ramips: add support for Wavlink WL-WN533A8
The Wavlink WL-WN533A8 is an AC3000 router with 5 gigabit ethernet ports
and one USB 3.0 port.
It's also known as Wavlink QUANTUM T8.
Hardware
--------
SoC: Mediatek MT7621A
RAM: 128MB (Nanya NT5CB64M16GP-EK)
FLASH: 16MB NOR (GigaDevice GD25Q127CSIG3)
ETH:
- 5x 10/100/1000 Mbps Ethernet (4x LAN + 1x WAN)
WIFI:
- 1x MT7615DN (2x 2x2:2) 2.4GHz and 5GHz DBDC
- 1x MT7615NE (4x4:4) 5GHz
- 8 external antennas
BTN:
- 1x Reset button
- 1x WPS button
- 1x Turbo button
- 1x Touchlink button
- 1x ON/OFF switch
LEDS:
- 1x Red led (system status)
- 1x Blue led (system status)
- 7x Blue leds (wifi led + 5 ethernet ports + power)
USB:
- 1x USB 3.0 port
UART:
- 57600-8-N-1
J4
Everything works correctly.
Installation
------------
Flash the initramfs image in the OEM firmware interface
(http://192.168.10.1/update.shtml).
When Openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.
(Procedure tested on fw M33A8.V5030.190716 and M33A8.V5030.201204)
Restore OEM Firmware
--------------------
Flash the firmware update available online directly from LUCI.
You can download it from:
https://www.wavlink.com/en_us/firmware/details/
f2d247ecba.html
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.
Notes
-----
1) Router mac addresses:
LAN XX:XX:XX:XX:XX:63 (factory @ 0xe006)
WAN XX:XX:XX:XX:XX:64 (factory @ 0xe000)
WIFI 2G/5G XX:XX:XX:XX:XX:65 (factory @ 0x04)
WIFI 5G XX:XX:XX:XX:XX:66 (factory @ 0x8004)
LABEL XX:XX:XX:XX:XX:65
In OEM firmware the DBDC wifi interfaces have these mac addresses:
2G) 82:XX:XX:XX:XX:65
5G) 80:XX:XX:XX:XX:65
While in OpenWrt the addresses are:
2G) 80:XX:XX:XX:XX:65
5G) 02:XX:XX:XX:XX:65
2) radio0 will show as 2G/5G interface but only 2G is really usable.
3) There is just one wifi led for all wifi interfaces.
It currently shows only the radio0 GHz wifi activity.
4) My unit was shipped with M33A8.V5030.190716 firmware which contains
the http://192.168.10.1/webcmd.shtml page. Entering "telnetd" in
the input box it will start the telnet daemon. Now you can access
the telnet console on port 2323 with these credentials:
username: admin2860
password: admin
5) The M33A8.V5030.201204 firmware version, doesn't contain anymore the
webcmd.shtml page. If your router is shipped with a previous firmware
version and you want to back it up, you can follow the back up
procedure of the WS-WN583A6.
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Davide Fioravanti [Mon, 18 Apr 2022 14:54:40 +0000 (16:54 +0200)]
ramips: create shared DTSI for Wavlink WN53XAX devices
Most of the definitions for WN531A6 will be shared with WN533A8 in a
future commit, so put them in a shared DTSI.
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Martin Kennedy [Tue, 26 Apr 2022 21:04:06 +0000 (17:04 -0400)]
mpc85xx: Fix output location of padded dtb
In commit
7e614820a892 ("mpc85xx: add support for Extreme Networks
WS-AP3825i"), we borrowed a recipe convention from apm821xx for device
tree blob padding. Unfortunately, in the apm821xx target, the image
recipes name the device tree blob differently, meaning that in
mpc85xx, the padded dtb is never consumed.
Change the definition of `Build/dtb` so that it outputs the padded dtb
to the correct location for it to be consumed.
Also, rename the recipe to `Build/pad-dtb`, so it is clear we
are building and padding the device tree blob.
This change fixes Github issue #9779 [1].
[1]: https://github.com/openwrt/openwrt/issues/9779
Fixes: 7e614820a892 ("mpc85xx: add support for Extreme Networks WS-AP3825i")
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
Huangbin Zhan [Sun, 24 Apr 2022 01:58:25 +0000 (09:58 +0800)]
build: don't remove BUILD_LOG_DIR in _clean
targetclean should not remove BUILD_LOG
Fixes: db34b93331e9 (add a version that can be bumped to force toolchain/target rebuild)
Signed-off-by: Huangbin Zhan <zhanhb88@gmail.com>
Robert Marko [Sat, 30 Apr 2022 18:17:24 +0000 (20:17 +0200)]
kernel: 5.15: add missing symbol
CONFIG_QCOM_SPMI_ADC_TM5 gets uncovered while building IPQ40xx with 5.15.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
John Audia [Wed, 27 Apr 2022 18:14:45 +0000 (14:14 -0400)]
kernel: bump 5.10 to 5.10.113
All patches automatically rebased.
Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200
Signed-off-by: John Audia <graysky@archlinux.us>
Chuanhong Guo [Sat, 30 Apr 2022 15:08:00 +0000 (23:08 +0800)]
mediatek: build ubnt-ledbar as a module
The config for LEDS_UBNT_LEDBAR doesn't stay in mt7629 kconfig because
of its I2C dependency. Build it as a module and let buildroot handle
this config option instead.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Sat, 30 Apr 2022 14:49:26 +0000 (22:49 +0800)]
mediatek: mt7629: disable auxadc in kconfig
manually edit kconfig to disable MT6577_AUXADC
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Sat, 30 Apr 2022 14:35:27 +0000 (22:35 +0800)]
mediatek: mt7623: disable various input devices
Disable support for joysticks, micee and tablets. There's no actual
driver selected in kconfig, and including kernel support is just a
waste of space. Besides that, I believe nobody wants these on a router.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Sat, 30 Apr 2022 12:24:07 +0000 (20:24 +0800)]
mediatek: mt7622: add irq for spi-nor controller
Save some CPU from unnecessary polling and make SPI flash reading
a tiny bit faster.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Daniel Golle [Sat, 30 Apr 2022 14:51:21 +0000 (15:51 +0100)]
mediatek: remove left-overs from Linux 5.10
Remove patches and configuration for Linux 5.10 which have been left
in the tree despite the target having been switched to Linux 5.15.
Fixes: c283defa88 ("mediatek: switch to 5.15")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sat, 30 Apr 2022 14:48:58 +0000 (15:48 +0100)]
mediatek: enable multi-core scheduling
Set CONFIG_SCHED_MC in config-5.15 to have make the scheduler aware
of shared caches.
Reported-by: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sat, 30 Apr 2022 14:17:46 +0000 (15:17 +0100)]
mediatek: refresh patches for Linux 5.15
Run `make target/linux/refresh` to align patches with OpenWrt style.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sat, 30 Apr 2022 14:41:13 +0000 (15:41 +0100)]
mediatek: backport recent DTS improvements for MT7622 SoC
Daniel Golle:
190-arm64-dts-mediatek-mt7622-fix-GICv2-range.patch
Rui Salvaterra:
191-arm64-dts-mt7622-specify-the-L2-cache-topology.patch
192-arm64-dts-mt7622-specify-the-number-of-DMA-requests.patch
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sat, 30 Apr 2022 14:14:01 +0000 (15:14 +0100)]
kernel: don't parse FIT partition on NAND-backed mtdblock
ubiblock devices should be used on NAND flash to store the uImage.FIT
in case the bootloader supports that -- otherwise only rootfs is stored
in UBI while the uImage.FIT contains only the kernel and dtb.
Hence there is no need to enable parsing partitions on NAND mtdblock
devices, it is even responsible for the ugly warning on-opening of the
mtdblock device now. Just don't do it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sat, 30 Apr 2022 13:24:41 +0000 (14:24 +0100)]
kernel: backport patch to relax mtdblock NAND warning
Instead of warning loudly about mtdblock devices being created, rather
just warn if they are actually used.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Chuanhong Guo [Fri, 29 Apr 2022 03:47:04 +0000 (11:47 +0800)]
mediatek: mt7629: disable mtk thermal
Manually edit kconfig to disable CONFIG_MTK_THERMAL
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Fri, 29 Apr 2022 03:32:51 +0000 (11:32 +0800)]
mediatek: mt7623: disable ecc engine support
There's no board using nand on this target atm.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Fri, 29 Apr 2022 02:44:51 +0000 (10:44 +0800)]
mediatek: mt7623 enable arch-timer with a patch
Last attempt on this has a typo and doen't work.
It seems that this is a common problem occurring on every kernel bump,
so let's enforce arch timer support for mt7623 with a patch instead.
Fixes: 9a22943eb2 ("mediatek: 5.15: re-enable arch timer on MT7623 as well")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Nick Hainke [Mon, 18 Apr 2022 13:04:25 +0000 (15:04 +0200)]
ipq40xx: 5.10: fix ar40xx driver
This commit is completely based on the work of adron-s:
https://github.com/openwrt/openwrt/pull/4721#issuecomment-
1101108651
The commit fixes the data corruption on TX packets. Packets are
transmitted, but their contents are replaced with zeros. This error is
caused by the lack of guard (50 ms) intervals between calibration phases.
This error is treated by adding mdelay(50) to the calibration function
code. In the original qca-ssda code [0], these mdelays were existing, but
in the ar41xx.c they are gone.
Tested on:
- Fritz!Box 4040
- Fritz!Box 7530
- Mikrotik SXTsq 5AC
- ZyXEL NBG6617
- [0] https://git.codelinaro.org/clo/qsdk/oss/lklm/qca-ssdk/-/blob/NHSS.QSDK.11.4/src/init/ssdk_init.c#L2072
Suggested-by: Serhii Serhieiev <adron@mstnt.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Nick Hainke <vincent@systemli.org>
Chuanhong Guo [Thu, 14 Apr 2022 04:45:01 +0000 (12:45 +0800)]
mediatek: switch to 5.15
the SPI-NAND driver switch breaks dts compatibility. It's too much work
to backport all ECC framework support to 5.10 so let's switch the target
to 5.15 instead.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Sat, 9 Apr 2022 05:26:50 +0000 (13:26 +0800)]
mediatek: enable snfi for mt7629
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Sat, 9 Apr 2022 12:18:40 +0000 (20:18 +0800)]
mediatek: restore support for Fidelix FM35X1GA
This patch was dropped when the spi-nand driver got replaced last time.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Thu, 7 Apr 2022 02:16:47 +0000 (10:16 +0800)]
mediatek: add an upstreamed spi-nand driver
This patch implements the spi-nand controller driver as an ECC-capable
spi-mem controller to use the upstream SPI-NAND driver.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Thu, 7 Apr 2022 02:05:56 +0000 (10:05 +0800)]
mediatek: spi-nand: check for 1 byte BBM only
the OOB layout in MTK SNFI uses the 2nd byte, and anything using OOB
will make the block a bad-block in spi-nand driver.
Hack it for now. We need a proper solution upstream.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Thu, 7 Apr 2022 02:05:25 +0000 (10:05 +0800)]
mediatek: v5.15: backport spi-mem ecc support
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Thu, 7 Apr 2022 02:03:50 +0000 (10:03 +0800)]
mediatek: drop spi-nand driver from mtk
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Jo-Philipp Wich [Thu, 28 Apr 2022 08:28:20 +0000 (10:28 +0200)]
ucode: reorder BuildPackage calls
Ensure that the libucode recipe is processed before the ucode one in
order to reliably encode the ABI version into ucode's libucode dependency.
Fixes: #9788
Ref: https://forum.openwrt.org/t/fw4-wont-start-after-upgrade/126308
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Sander Vanheule [Wed, 27 Apr 2022 15:27:28 +0000 (17:27 +0200)]
ath79: add support for TP-Link EAP265 HD
The EAP265 HD is a rebadged EAP245v3, so images are compatible with both
devices.
Link: https://fccid.io/TE7EAP265HD/Letter/6-Request-for-FCC-Change-ID-4823578.pdf
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Sander Vanheule [Wed, 27 Apr 2022 15:27:28 +0000 (17:27 +0200)]
firmware-utils: bump to git HEAD
Includes image support for new TP-Link devices:
ddc3e00e314d tplink-safeloader: add TP-Link EAP265 HD support
ceea1a7fe56e tplink-safeloader: add TP-Link Deco M4R v1 and v2 support
Signed-off-by: Sander Vanheule <sander@svanheule.net>
David Bauer [Tue, 26 Apr 2022 22:53:11 +0000 (00:53 +0200)]
iwinfo: update to latest HEAD
dc6847e iwinfo: nl80211: omit A-hwmode on non-5GHz hardware
Signed-off-by: David Bauer <mail@david-bauer.net>
Hans Dedecker [Tue, 26 Apr 2022 20:39:02 +0000 (22:39 +0200)]
nat46: update to git HEAD
95ca1c3 nat46-core: ignore IPv4 options when translating packets
39778c2 add a module argument to ignore TOS translate for IPv4
9a36ee1 add a module argument to ignore TOS translate for IPv4
79190a8 add a module argument to ignore TOS translate for IPv4
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
David Bauer [Sun, 24 Apr 2022 22:04:09 +0000 (00:04 +0200)]
uboot-envtools: add WS-AP3825i config
Add configuration to use uboot-envtools with the Extreme Networks
WS-AP3825i.
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Sun, 24 Apr 2022 23:00:49 +0000 (01:00 +0200)]
mpc85xx: set WS-AP3825i mac-address in preinit
The bootloader does seem to not correctly patch in the MAC address for
eth0 / eth1 in some cases. While the root cause is not known, manually
applying the MAC-Address in preinit does not hurt.
Reported-by: Tom Herbers <freifunk@tomherbers.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Sun, 24 Apr 2022 21:48:42 +0000 (23:48 +0200)]
mpc85xx: define reset-delay for WS-AP3825i eth PHY
The WS-AP3825i uses Atheros PHYs which according to the datasheet
require the reset to be asserted for at least 1 ms.
This fixes broken eth1 upon soft-reboot. eth0 is no affected, as the
ifup / ifdown cycle in preinit prevents this issue from happening when
the system is ready.
Reported-by: Tom Herbers <freifunk@tomherbers.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
Daniel Golle [Mon, 25 Apr 2022 17:56:52 +0000 (18:56 +0100)]
dnsmasq: add logfacility file to jail mounts
If logfacility is a path to a file it needs to be r/w mounted in the
sandbox as well for dnsmasq to work.
Reported-by: @iointerrupt
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
David Bauer [Sun, 24 Apr 2022 21:09:09 +0000 (23:09 +0200)]
iwinfo: update to latest HEAD
a479b9b devices: remove whitespace
562d015 iwinfo: nl80211: fix hwmode parsing for multi-band NICs
Signed-off-by: David Bauer <mail@david-bauer.net>
Martin Weinelt [Sun, 17 Apr 2022 13:56:53 +0000 (15:56 +0200)]
ath79: ubnt: drop swconfig on ac-{lite,lr,mesh}
These don't have switches that could be configured using swconfig.
Signed-off-by: Martin Weinelt <hexa@darmstadt.ccc.de>
Marcin Gordziejewski [Thu, 7 Apr 2022 22:29:20 +0000 (00:29 +0200)]
ramips: add support for TP-Link RE650 v2
TP-Link RE650 v2 is largely similar to v1 that
is already supported by OpenWrt. Notable differences
is differnt SPI Flash - 8 MB instead of 16 MB
(from cFeon instead of Winbond) and a different
configuration of PCIE connections to wifi chips.
Otherwise it's largely the same product as v1
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 8 MB - cFeon QH64A-104HIP
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART pinout - GND, RX, TX, labeled in the middle of the PCB,
requires soldering because they're not through holes.
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re650-v2-squashfs-factory.bin
from the RE650 web interface.
TFTP recovery to stock firmware:
I didn't try recovering back to the stock firmware, however,
if there is such process for other RExxx devices, it seems like
it could be similar here.
Signed-off-by: Marcin Gordziejewski <openwrt@flicksfix.com>
Hauke Mehrtens [Sat, 23 Apr 2022 19:57:09 +0000 (21:57 +0200)]
firmware-utils: bump to git HEAD
05fd700 tplink-safeloader: TP-Link RE650 v2 support
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Clemens Hopfer [Thu, 22 Jul 2021 15:54:15 +0000 (17:54 +0200)]
ramips: add support for YunCore AX820/HWAP-AX820
There are two versions which are identical apart from the enclosure:
YunCore AX820: indoor ceiling mount AP with integrated antennas
YunCore HWAP-AX820: outdoor enclosure with external (N) connectors
Hardware specs:
SoC: MediaTek MT7621DAT
Flash: 16 MiB SPI NOR
RAM: 128MiB (DDR3, integrated)
WiFi: MT7905DAN+MT7975DN 2.4/5GHz 2T2R 802.11ax
Ethernet: 10/100/1000 Mbps x2 (WAN/PoE+LAN)
LED: Status (green)
Button: Reset
Power: 802.11af/at PoE; DC 12V,1A
Antennas: AX820(indoor): 4dBi internal; HWAP-AX820(outdoor): external
Flash instructions:
The "OpenWRT support" version of the AX820 comes with a LEDE-based
firmware with proprietary MTK drivers and a luci webinterface and
ssh accessible under 192.168.1.1 on LAN; user root, no password.
The sysupgrade.bin can be flashed using luci or sysupgrade via ssh,
you will have to force the upgrade due to a different factory name.
Remember: Do *not* preserve factory configuration!
MAC addresses as used by OEM firmware:
use address source
2g 44:D1:FA:*:0b Factory 0x0004 (label)
5g 46:D1:FA:*:0b LAA of 2g
lan 44:D1:FA:*:0c Factory 0xe000
wan 44:D1:FA:*:0d Factory 0xe000 + 1
The wan MAC can also be found in 0xe006 but is not used by OEM dtb.
Due to different MAC handling in mt76 the LAA derived from lan is used
for 2g to prevent duplicate MACs when creating multiple interfaces.
Signed-off-by: Clemens Hopfer <openwrt@wireloss.net>
Rui Salvaterra [Wed, 20 Apr 2022 08:07:51 +0000 (09:07 +0100)]
kernel: bump 5.15 to 5.15.35
Patches automatically rebased.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
John Audia [Wed, 20 Apr 2022 10:44:30 +0000 (06:44 -0400)]
kernel: bump 5.10 to 5.10.112
Manually rebased:
ath79/patches-5.10/901-phy-mdio-bitbang-prevent-rescheduling-during-command.patch
All other patches automatically rebased.
Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200
Signed-off-by: John Audia <graysky@archlinux.us>
Huangbin Zhan [Wed, 20 Apr 2022 21:40:40 +0000 (05:40 +0800)]
bcm63xx: fix description fix name case
The `Description` should be capital.
Signed-off-by: Huangbin Zhan <zhanhb88@gmail.com>
Lech Perczak [Sat, 23 Apr 2022 09:22:50 +0000 (11:22 +0200)]
ath79: ZTE MF286R: add comgt-ncm to DEVICE_PACKAGES
When adding support to the router's built-in modem, this required
package was omitted, because it was already enabled in the image
configuration in use for testing, and this went unnoticed.
In result, the modem still isn't fully supported in official images.
As it is the primary WAN interface, add the missing package.
Fixes: e02fb42c53ba ("comgt: support ZTE MF286R modem")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Felix Fietkau [Sat, 23 Apr 2022 13:50:37 +0000 (15:50 +0200)]
mt76: update to the latest version
a666d5637bc3 mt76: fix tx status related use-after-free race on station removal
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Jo-Philipp Wich [Fri, 22 Apr 2022 07:23:49 +0000 (09:23 +0200)]
ucode: fix PKG_MIRROR_HASH
Fixes: 0400774a10 ("ucode: update to latest Git HEAD")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Jo-Philipp Wich [Thu, 21 Apr 2022 19:24:44 +0000 (21:24 +0200)]
firewall4: update to latest Git HEAD
fc83d46 ruleset: set auto-merge directive for interval sets
9bce873 fw4: fix skipping invalid ipset entries
425ea8a fw4: fix applying zone flags for source bound rules
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Jo-Philipp Wich [Thu, 21 Apr 2022 18:59:15 +0000 (20:59 +0200)]
ucode: update to latest Git HEAD
e14b099 syntax: implement support for ES6 template literals
111cf06 vm: stop executing bytecode on return of nested calls
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Felix Fietkau [Wed, 20 Apr 2022 13:14:14 +0000 (15:14 +0200)]
mt76: update to the latest version
d4937118ec4f mt76: fix rx reordering with non explicit / psmp ack policy
f50672518bcc mt76: do not attempt to reorder received 802.3 packets without agg session
75e046e3c9ae mt76: fix antenna config missing in 6G cap
64ede85f14b5 mt76: mt7915: remove SCS feature
db0a67582028 mt76: mt7915: make read-only array ppet16_ppet8_ru3_ru0 static const
68a2f68d5c01 mt76: mt7921: make read-only array ppet16_ppet8_ru3_ru0 static const
1e7b77294e97 mt76: mt7921: fix kernel crash at mt7921_pci_remove
795830a99a6c mt76: mt7915: add debugfs knob for RF registers read/write
60a8ec12a8eb mt76: mt7603: move spin_lock_bh() to spin_lock()
5ec7a2eac867 mt76: mt7915: disable RX_HDR_TRANS_SHORT
eecbb4992073 mt76: fix encap offload ethernet type check
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Daniel Golle [Wed, 20 Apr 2022 14:19:59 +0000 (15:19 +0100)]
kernel: update FIT partition parser to new property name
The commit "uboot-mediatek: replace patch with accepted commit" changed
the name of the boot configuration property from 'bootconf' to
'u-boot,bootconf'. Reflect this change in the FIT partition parser.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Wed, 20 Apr 2022 14:10:07 +0000 (15:10 +0100)]
uboot-mediatek: replace patch with accepted commit
Replace pending patch with version accepted upstream.
Other than in the first suggested version, the new property is now
called 'u-boot,bootconf' instead of 'bootconf'.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Rui Salvaterra [Thu, 7 Apr 2022 16:14:38 +0000 (17:14 +0100)]
kernel: x86: remove an upstreamed patch
012-pcengines-apu2-detect-apuv4-board.patch is upstream since Linux 5.5 [1].
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.5&id=
3d00da1de3ea36ba44f4a7ba76c8c8b16f98204b
Acked-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Eneas U de Queiroz [Wed, 13 Apr 2022 13:30:15 +0000 (10:30 -0300)]
wolfssl: fix compilation with /dev/crypto
This is trivial fix of a duplicate definition of 'int ret'.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Felix Fietkau [Tue, 19 Apr 2022 19:14:42 +0000 (21:14 +0200)]
kernel: add missing config symbols
MPLS feature symbols are normally only set when kmod-mpls is enabled, but the
CONFIG_MPLS symbol they depend on could also have been selected by openvswitch
instead
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Paul Spooren [Tue, 19 Apr 2022 18:02:59 +0000 (20:02 +0200)]
build: use numeric-owner in ipkg-build
To create packages the `ipkg-build` script is used which double packs
`control.tar.gz` and `data.tar.gz` to a single package. By default it's
using a verbose username instead of a numeric value for files.
Official OpenWrt images (artifacts) are created within docker containers
which do not seem to contain those verbose usernames and instead
defaults to numeric values.
This becomes a problem when rebuilding public artifacts because other
build environments may offer verbose usernames and there the created
packages is different from the official ones.
With this commit `ipkg-build` always uses numeric values for user/group
and thereby making it easier to reproduce official artifacts.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Hauke Mehrtens [Mon, 18 Apr 2022 16:57:54 +0000 (18:57 +0200)]
toolchain: Update glibc 2.34 to recent HEAD
This adds the following changes:
31186e2cb7 elf: Sort tests and modules-names
511b244cc5 elf: Add a comment after trailing backslashes
de6cdd6875 elf/Makefile: Reflow and sort most variable assignments
948ebc098e Fix glibc 2.34 ABI omission (missing GLIBC_2.34 in dynamic loader)
b952c25dc7 x86: Black list more Intel CPUs for TSX [BZ #27398]
aa601d0244 x86: Use CHECK_FEATURE_PRESENT to check HLE [BZ #27398]
e09e7b1492 support: Add support_socket_so_timestamp_time64
e098446037 linux: Fix ancillary 64-bit time timestamp conversion (BZ #28349, BZ#28350)
489d0b8b32 Linux: Only generate 64 bit timestamps for 64 bit time_t recvmsg/recvmmsg
008003dc6e tst-socket-timestamp-compat.c: Check __TIMESIZE [BZ #28837]
05c83ccaf5 linux: __get_nprocs_sched: do not feed CPU_COUNT_S with garbage [BZ #28850]
ad615b59c7 Linux: Simplify __opensock and fix race condition [BZ #28353]
d8302ba2da hurd if_index: Explicitly use AF_INET for if index discovery
6eaf10cbb7 socket: Do not use AF_NETLINK in __opensock
0351c75c5f linux: Fix missing __convert_scm_timestamps (BZ #28860)
d64b08d5ba Add reference to BZ#28860 on NEWS
007e054d78 linux: fix accuracy of get_nprocs and get_nprocs_conf [BZ #28865]
04d60ce0f2 string: Add a testcase for wcsncmp with SIZE_MAX [BZ #28755]
38e0d24794 x86: Fallback {str|wcs}cmp RTM in the ncmp overflow case [BZ #28896]
d093b677c3 x86: Test wcscmp RTM in the wcsncmp overflow case [BZ #28896]
15b00d2af0 x86: Fix TEST_NAME to make it a string in tst-strncmp-rtm.c
d5d1c95aaf NEWS: Add a bug fix entry for BZ #28896
852361b5a3 localedef: Handle symbolic links when generating locale-archive
3be79b72d5 Fix elf/tst-audit2 on hppa
c6f9085ee4 hppa: Fix swapcontext
f610d2935f hppa: Revise gettext trampoline design
40fc6a74ee nptl: Fix cleanups for stack grows up [BZ# 28899]
6c9c230765 hppa: Fix warnings from _dl_lookup_address
b5032c3d37 io: Add fsync call in tst-stat
b53f0c11de nss: Do not mention NSS test modules in <gnu/lib-names.h>
54b1273395 nss: Protect against errno changes in function lookup (bug 28953)
c82bdf033f Don't add access size hints to fortifiable functions
0e6ebf06e4 Make sure that the fortified function conditionals are constant
536910724d debug: Add tests for _FORTIFY_SOURCE=3
98ea9372cc __glibc_unsafe_len: Fix comment
10f7bdebe5 fortify: Fix spurious warning with realpath
d6a58bd81d Enable _FORTIFY_SOURCE=3 for gcc 12 and above
f8c2f620f1 debug: Autogenerate _FORTIFY_SOURCE tests
224d8c1890 debug: Synchronize feature guards in fortified functions [BZ #28746]
738ee53f0c hppa: Implement swapcontext in assembler (bug 28960)
d53b9cc391 hppa: Use END instead of PSEUDO_END in swapcontext.S
4b5b8a1cdf powerpc: Delete unneeded ELF_MACHINE_BEFORE_RTLD_RELOC
b19de59d62 elf: Avoid nested functions in the loader [BZ #27220]
c6df39a0bd elf: Fix elf_get_dynamic_info definition
b868b45f67 elf: Fix dynamic-link.h usage on rtld.c
f6a54a3042 elf: Fix elf_get_dynamic_info() for bootstrap
a31bbe3242 elf: Move LAV_CURRENT to link_lavcurrent.h
e25fe99213 elf: Move la_activity (LA_ACT_ADD) after _dl_add_to_namespace_list() (BZ #28062)
ce0cb6d1d2 elf: Add _dl_audit_objopen
66e9d27a09 elf: Add _dl_audit_activity_map and _dl_audit_activity_nsid
ec0fc2a153 elf: Add _dl_audit_objsearch
198660741b elf: Add _dl_audit_objclose
b2d99731b6 elf: Add _dl_audit_symbind_alt and _dl_audit_symbind
31473c273b elf: Add _dl_audit_preinit
fd9c4e8a1b elf: Add _dl_audit_pltenter
a8e211daea elf: Add _dl_audit_pltexit
29496b3103 elf: Avoid unnecessary slowdown from profiling with audit (BZ#15533)
02c6a3d353 elf: Add audit tests for modules with TLSDESC
d1b9bee29a elf: Issue audit la_objopen for vDSO
2255621f0e elf: Do not fail for failed dlmopen on audit modules (BZ #28061)
98047ba95c elf: Add la_activity during application exit
efb21b5fb2 elf: Fix initial-exec TLS access on audit modules (BZ #28096)
056fc1c0e3 elf: Issue la_symbind for bind-now (BZ #23734)
b118bce87a elf: Fix runtime linker auditing on aarch64 (BZ #26643)
165e7ad459 Fix elf/tst-audit25a with default bind now toolchains
aabdad371f elf: Replace tst-audit24bmod2.so with tst-audit24bmod2
4dca2d3a7b hppa: Fix bind-now audit (BZ #28857)
ceed89d089 NEWS: Update fixed bug list for LD_AUDIT backports.
0c03cb54c8 S390: Add new s390 platform z16.
290db09546 nptl: Handle spurious EINTR when thread cancellation is disabled (BZ#29029)
5d8c777634 hurd: Fix arbitrary error code
b87b697f15 mips: Fix mips64n32 64 bit time_t stat support (BZ#29069)
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Daniel Golle [Tue, 19 Apr 2022 15:27:22 +0000 (16:27 +0100)]
uboot-mediatek: remove '0x' prefix from pstore node
Remove '0x' prefix from pstore node in dts, just like it was done
for the device tree used by Linux on MT7622.
This change is done in preparation to update U-Boot to 2022.04.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Tue, 19 Apr 2022 15:23:08 +0000 (16:23 +0100)]
mediatek: mt7622: remove '0x' prefix from pstore address in dts
Adresses of device tree nodes are typically noted without the '0x'
prefix. While having the '0x' prefix doesn't hurt when using Linux,
more recent versions of U-Boot will add a duplicate ramoops node as a
simple string compare is used to check if the node is already present.
Remove the '0x' prefix to avoid the kernel warning resulting from
U-Boot adding a dupplicate pstore/ramoops node.
See also https://lists.denx.de/pipermail/u-boot/2022-April/481810.html
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Rodrigo Balerdi [Fri, 15 Apr 2022 10:20:28 +0000 (07:20 -0300)]
base-files: minimize critical time in sysupgrade
Attempt to minimize the time during which an interrupted nand sysupgrade
can lead to a non-functional device by flushing caches before starting
the upgrade procedure.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Rodrigo Balerdi [Fri, 15 Apr 2022 13:15:02 +0000 (10:15 -0300)]
base-files: trim unnecessary nand sysupgrade code
Remove unnecessary sync commands during nand sysupgrade.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Rodrigo Balerdi [Fri, 15 Apr 2022 13:11:52 +0000 (10:11 -0300)]
base-files: fix issues in nand sysupgrade
Fix issues while retaining configuration during nand sysupgrade:
- abort configuration saving if data partition is not found
- generate diagnostics if saving fails (eg, because of lack of space)
- do not output "sysupgrade successful" in case of errors
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Rodrigo Balerdi [Fri, 15 Apr 2022 10:18:22 +0000 (07:18 -0300)]
base-files: clean up nand sysupgrade code
Fix some inconsistent quoting in nand sysupgrade code.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Rodrigo Balerdi [Fri, 15 Apr 2022 09:42:51 +0000 (06:42 -0300)]
base-files: clean up ubinized sysupgrade code
Remove redundant check from nand ubinized sysupgrade code. This check
has already been done in the only caller of the affected function:
nand_do_upgrade.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Rodrigo Balerdi [Fri, 15 Apr 2022 09:31:24 +0000 (06:31 -0300)]
base-files: clean up nand tar sysupgrade code
Prepares code for ubirename-based safe sysupgrade implementation.
Fixes several issues:
- the special CI_KERNPART value "none" is ignored if an MTD partition
named "none" exists
- misleading variable names (such as has_kernel to mean "tar has kernel
and it should not be written to an MTD partition but a UBI volume")
- inconsistent treatment of zero-length tar member files
- inconsistent meaning of "0" and "" variable values
- redundant operations (unneeded untaring, repeated untaring, unneeded
partition lookups)
- inconsistent variable quoting
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Rodrigo Balerdi [Fri, 15 Apr 2022 06:24:58 +0000 (03:24 -0300)]
base-files: safer sysupgrade.tar for kernel-out-of-UBI
Ensure that the kernel CRC is invalidated while rootfs is being updated.
This allows the bootloader to detect an interrupted sysupgrade and fall
back to an alternate booting method, such as TFTP, instead of just going
ahead with normal boot and effectively bricking the device.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Rodrigo Balerdi [Fri, 15 Apr 2022 03:59:49 +0000 (00:59 -0300)]
base-files: safer sysupgrade for kernel-in-UBI devices
Ensure that the kernel CRC is invalidated while rootfs is being updated.
This allows the bootloader to detect an interrupted sysupgrade and fall
back to an alternate booting method, instead of just going ahead with
normal boot and effectively bricking the device.
Possible fallbacks include a recovery initramfs partition or UBI volume
and TFTP. See here for an example U-Boot configuration with fallbacks:
https://shorturl.at/befsA (https://github.com/Lanchon/openwrt-tr4400-v2/
blob/
e7d707d6bd7839fbd0b8d0bd180fce451df77e47/install-recovery.sh#L52-L63)
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Rodrigo Balerdi [Fri, 15 Apr 2022 03:53:27 +0000 (00:53 -0300)]
base-files: fix nand sysupgrade comments
Erroneous comments possibly applied to an earlier code revision.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Rodrigo Balerdi [Fri, 15 Apr 2022 03:52:12 +0000 (00:52 -0300)]
base-files: improve sysupgrade ubiblock handling
Only remove ubiblock devices required for nand sysupgrade.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Rodrigo Balerdi [Fri, 15 Apr 2022 03:44:26 +0000 (00:44 -0300)]
base-files: emit diagnostics on sysupgrade abort
Emit diagnostics if nand sysupgrade is aborted because UBI partition
cannot be attached. Also avoid redudndant checks.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Eneas U de Queiroz [Thu, 31 Mar 2022 13:38:49 +0000 (10:38 -0300)]
mediatek: remove crypto-hw-mtk package
The MediaTek's Crypto Engine module is only available for mt7623, in
which case it is built into the kernel.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
David Musil [Sat, 16 Apr 2022 12:01:31 +0000 (12:01 +0000)]
ath79: add support for MikroTik RouterBOARD wAP-2nD (wAP)
The MikroTik RouterBOARD wAP-2nd (sold as wAP) is a small
2.4 GHz 802.11b/g/n PoE-capable AP.
Specifications:
- SoC: Qualcomm Atheros QCA9533
- Flash: 16 MB (SPI)
- RAM: 64 MB
- Ethernet: 1x 10/100 Mbps (PoE in)
- WiFi: AR9531 2T2R 2.4 GHz (SoC)
- 3x green LEDs (1x lan, 1x wlan, 1x user)
See https://mikrotik.com/product/RBwAP2nD for more info.
Flashing:
TFTP boot initramfs image and then perform sysupgrade. Follow common
MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.
Note: following
781d4bfb397cdd12ee0151eb66c577f470e3377d
The network setup avoids using the integrated switch and connects the
single Ethernet port directly. This way, link speed (10/100 Mbps) is
properly reported by eth0.
Signed-off-by: David Musil <0x444d@protonmail.com>
Thibaut VARÈNE [Sun, 17 Apr 2022 15:03:52 +0000 (17:03 +0200)]
mac80211: fix QCA9561 PA bias
This patch fixes an invalid TX PA DC bias level on QCA9561, which
results in a very low output power and very low throughput as devices
are further away from the AP (compared to other 2.4GHz APs),
following a suggestion from nbd[1].
This patch has been submitted upstream[2].
[1] https://lore.kernel.org/all/
91c58969-c60e-2f41-00ac-
737786d435ae@nbd.name
[2] https://lore.kernel.org/linux-wireless/
20220417145145.1847-1-hacks+kernel@slashdirt.org/
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Hauke Mehrtens [Mon, 11 Apr 2022 22:12:57 +0000 (00:12 +0200)]
linux-firmware: Update to version
20220411
The following files used in OpenWrt changed:
amd64-microcode/lib/firmware/amd-ucode/microcode_amd_fam17h.bin
amd64-microcode/lib/firmware/amd-ucode/microcode_amd_fam19h.bin
amdgpu-firmware/lib/firmware/amdgpu/aldebaran_mec.bin
amdgpu-firmware/lib/firmware/amdgpu/aldebaran_mec2.bin
amdgpu-firmware/lib/firmware/amdgpu/aldebaran_rlc.bin
amdgpu-firmware/lib/firmware/amdgpu/aldebaran_sdma.bin
amdgpu-firmware/lib/firmware/amdgpu/aldebaran_smc.bin
amdgpu-firmware/lib/firmware/amdgpu/aldebaran_sos.bin
amdgpu-firmware/lib/firmware/amdgpu/aldebaran_ta.bin
amdgpu-firmware/lib/firmware/amdgpu/aldebaran_vcn.bin
amdgpu-firmware/lib/firmware/amdgpu/arcturus_sdma.bin
amdgpu-firmware/lib/firmware/amdgpu/beige_goby_ce.bin
amdgpu-firmware/lib/firmware/amdgpu/beige_goby_dmcub.bin
amdgpu-firmware/lib/firmware/amdgpu/beige_goby_me.bin
amdgpu-firmware/lib/firmware/amdgpu/beige_goby_mec.bin
amdgpu-firmware/lib/firmware/amdgpu/beige_goby_mec2.bin
amdgpu-firmware/lib/firmware/amdgpu/beige_goby_pfp.bin
amdgpu-firmware/lib/firmware/amdgpu/beige_goby_rlc.bin
amdgpu-firmware/lib/firmware/amdgpu/beige_goby_sdma.bin
amdgpu-firmware/lib/firmware/amdgpu/beige_goby_smc.bin
amdgpu-firmware/lib/firmware/amdgpu/beige_goby_sos.bin
amdgpu-firmware/lib/firmware/amdgpu/beige_goby_ta.bin
amdgpu-firmware/lib/firmware/amdgpu/beige_goby_vcn.bin
amdgpu-firmware/lib/firmware/amdgpu/cyan_skillfish2_ce.bin
amdgpu-firmware/lib/firmware/amdgpu/cyan_skillfish2_me.bin
amdgpu-firmware/lib/firmware/amdgpu/cyan_skillfish2_mec.bin
amdgpu-firmware/lib/firmware/amdgpu/cyan_skillfish2_mec2.bin
amdgpu-firmware/lib/firmware/amdgpu/cyan_skillfish2_pfp.bin
amdgpu-firmware/lib/firmware/amdgpu/dcn_3_1_6_dmcub.bin
amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_ce.bin
amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_dmcub.bin
amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_me.bin
amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_mec.bin
amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_mec2.bin
amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_pfp.bin
amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_rlc.bin
amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_sdma.bin
amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_smc.bin
amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_sos.bin
amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_ta.bin
amdgpu-firmware/lib/firmware/amdgpu/dimgrey_cavefish_vcn.bin
amdgpu-firmware/lib/firmware/amdgpu/gc_10_3_7_ce.bin
amdgpu-firmware/lib/firmware/amdgpu/gc_10_3_7_me.bin
amdgpu-firmware/lib/firmware/amdgpu/gc_10_3_7_mec.bin
amdgpu-firmware/lib/firmware/amdgpu/gc_10_3_7_mec2.bin
amdgpu-firmware/lib/firmware/amdgpu/gc_10_3_7_pfp.bin
amdgpu-firmware/lib/firmware/amdgpu/gc_10_3_7_rlc.bin
amdgpu-firmware/lib/firmware/amdgpu/green_sardine_asd.bin
amdgpu-firmware/lib/firmware/amdgpu/green_sardine_ce.bin
amdgpu-firmware/lib/firmware/amdgpu/green_sardine_dmcub.bin
amdgpu-firmware/lib/firmware/amdgpu/green_sardine_me.bin
amdgpu-firmware/lib/firmware/amdgpu/green_sardine_mec.bin
amdgpu-firmware/lib/firmware/amdgpu/green_sardine_mec2.bin
amdgpu-firmware/lib/firmware/amdgpu/green_sardine_pfp.bin
amdgpu-firmware/lib/firmware/amdgpu/green_sardine_rlc.bin
amdgpu-firmware/lib/firmware/amdgpu/green_sardine_ta.bin
amdgpu-firmware/lib/firmware/amdgpu/green_sardine_vcn.bin
amdgpu-firmware/lib/firmware/amdgpu/navi10_asd.bin
amdgpu-firmware/lib/firmware/amdgpu/navi10_ce.bin
amdgpu-firmware/lib/firmware/amdgpu/navi10_me.bin
amdgpu-firmware/lib/firmware/amdgpu/navi10_mec.bin
amdgpu-firmware/lib/firmware/amdgpu/navi10_mec2.bin
amdgpu-firmware/lib/firmware/amdgpu/navi10_pfp.bin
amdgpu-firmware/lib/firmware/amdgpu/navi10_sos.bin
amdgpu-firmware/lib/firmware/amdgpu/navi10_ta.bin
amdgpu-firmware/lib/firmware/amdgpu/navi10_vcn.bin
amdgpu-firmware/lib/firmware/amdgpu/navi12_asd.bin
amdgpu-firmware/lib/firmware/amdgpu/navi12_sdma.bin
amdgpu-firmware/lib/firmware/amdgpu/navi12_sdma1.bin
amdgpu-firmware/lib/firmware/amdgpu/navi12_sos.bin
amdgpu-firmware/lib/firmware/amdgpu/navi12_ta.bin
amdgpu-firmware/lib/firmware/amdgpu/navi12_vcn.bin
amdgpu-firmware/lib/firmware/amdgpu/navi14_asd.bin
amdgpu-firmware/lib/firmware/amdgpu/navi14_smc.bin
amdgpu-firmware/lib/firmware/amdgpu/navi14_sos.bin
amdgpu-firmware/lib/firmware/amdgpu/navi14_ta.bin
amdgpu-firmware/lib/firmware/amdgpu/navi14_vcn.bin
amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_ce.bin
amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_dmcub.bin
amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_me.bin
amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_mec.bin
amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_mec2.bin
amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_pfp.bin
amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_rlc.bin
amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_sdma.bin
amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_smc.bin
amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_sos.bin
amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_ta.bin
amdgpu-firmware/lib/firmware/amdgpu/navy_flounder_vcn.bin
amdgpu-firmware/lib/firmware/amdgpu/picasso_asd.bin
amdgpu-firmware/lib/firmware/amdgpu/picasso_ce.bin
amdgpu-firmware/lib/firmware/amdgpu/picasso_me.bin
amdgpu-firmware/lib/firmware/amdgpu/picasso_mec.bin
amdgpu-firmware/lib/firmware/amdgpu/picasso_mec2.bin
amdgpu-firmware/lib/firmware/amdgpu/picasso_pfp.bin
amdgpu-firmware/lib/firmware/amdgpu/picasso_ta.bin
amdgpu-firmware/lib/firmware/amdgpu/picasso_vcn.bin
amdgpu-firmware/lib/firmware/amdgpu/psp_13_0_8_asd.bin
amdgpu-firmware/lib/firmware/amdgpu/psp_13_0_8_ta.bin
amdgpu-firmware/lib/firmware/amdgpu/psp_13_0_8_toc.bin
amdgpu-firmware/lib/firmware/amdgpu/raven2_asd.bin
amdgpu-firmware/lib/firmware/amdgpu/raven2_ce.bin
amdgpu-firmware/lib/firmware/amdgpu/raven2_me.bin
amdgpu-firmware/lib/firmware/amdgpu/raven2_mec.bin
amdgpu-firmware/lib/firmware/amdgpu/raven2_mec2.bin
amdgpu-firmware/lib/firmware/amdgpu/raven2_pfp.bin
amdgpu-firmware/lib/firmware/amdgpu/raven2_ta.bin
amdgpu-firmware/lib/firmware/amdgpu/raven2_vcn.bin
amdgpu-firmware/lib/firmware/amdgpu/raven_asd.bin
amdgpu-firmware/lib/firmware/amdgpu/raven_ce.bin
amdgpu-firmware/lib/firmware/amdgpu/raven_me.bin
amdgpu-firmware/lib/firmware/amdgpu/raven_mec.bin
amdgpu-firmware/lib/firmware/amdgpu/raven_mec2.bin
amdgpu-firmware/lib/firmware/amdgpu/raven_pfp.bin
amdgpu-firmware/lib/firmware/amdgpu/raven_ta.bin
amdgpu-firmware/lib/firmware/amdgpu/raven_vcn.bin
amdgpu-firmware/lib/firmware/amdgpu/renoir_asd.bin
amdgpu-firmware/lib/firmware/amdgpu/renoir_ce.bin
amdgpu-firmware/lib/firmware/amdgpu/renoir_dmcub.bin
amdgpu-firmware/lib/firmware/amdgpu/renoir_me.bin
amdgpu-firmware/lib/firmware/amdgpu/renoir_mec.bin
amdgpu-firmware/lib/firmware/amdgpu/renoir_mec2.bin
amdgpu-firmware/lib/firmware/amdgpu/renoir_pfp.bin
amdgpu-firmware/lib/firmware/amdgpu/renoir_rlc.bin
amdgpu-firmware/lib/firmware/amdgpu/renoir_ta.bin
amdgpu-firmware/lib/firmware/amdgpu/renoir_vcn.bin
amdgpu-firmware/lib/firmware/amdgpu/sdma_5_2_7.bin
amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_ce.bin
amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_dmcub.bin
amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_me.bin
amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_mec.bin
amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_mec2.bin
amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_pfp.bin
amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_rlc.bin
amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_sdma.bin
amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_smc.bin
amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_sos.bin
amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_ta.bin
amdgpu-firmware/lib/firmware/amdgpu/sienna_cichlid_vcn.bin
amdgpu-firmware/lib/firmware/amdgpu/vangogh_asd.bin
amdgpu-firmware/lib/firmware/amdgpu/vangogh_ce.bin
amdgpu-firmware/lib/firmware/amdgpu/vangogh_me.bin
amdgpu-firmware/lib/firmware/amdgpu/vangogh_mec.bin
amdgpu-firmware/lib/firmware/amdgpu/vangogh_mec2.bin
amdgpu-firmware/lib/firmware/amdgpu/vangogh_pfp.bin
amdgpu-firmware/lib/firmware/amdgpu/vega10_asd.bin
amdgpu-firmware/lib/firmware/amdgpu/vega10_ce.bin
amdgpu-firmware/lib/firmware/amdgpu/vega10_me.bin
amdgpu-firmware/lib/firmware/amdgpu/vega10_mec.bin
amdgpu-firmware/lib/firmware/amdgpu/vega10_mec2.bin
amdgpu-firmware/lib/firmware/amdgpu/vega10_pfp.bin
amdgpu-firmware/lib/firmware/amdgpu/vega12_asd.bin
amdgpu-firmware/lib/firmware/amdgpu/vega12_ce.bin
amdgpu-firmware/lib/firmware/amdgpu/vega12_me.bin
amdgpu-firmware/lib/firmware/amdgpu/vega12_mec.bin
amdgpu-firmware/lib/firmware/amdgpu/vega12_mec2.bin
amdgpu-firmware/lib/firmware/amdgpu/vega12_pfp.bin
amdgpu-firmware/lib/firmware/amdgpu/vega20_asd.bin
amdgpu-firmware/lib/firmware/amdgpu/vega20_ce.bin
amdgpu-firmware/lib/firmware/amdgpu/vega20_me.bin
amdgpu-firmware/lib/firmware/amdgpu/vega20_mec.bin
amdgpu-firmware/lib/firmware/amdgpu/vega20_mec2.bin
amdgpu-firmware/lib/firmware/amdgpu/vega20_pfp.bin
amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_asd.bin
amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_ce.bin
amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_me.bin
amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_mec.bin
amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_mec2.bin
amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_pfp.bin
amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_rlc.bin
amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_ta.bin
ibt-firmware/lib/firmware/intel/ibt-hw-37.8.10-fw-22.50.19.14.f.bseq
iwlwifi-firmware-ax210/lib/firmware/iwlwifi-ty-a0-gf-a0.pnvm
iwlwifi-firmware-iwl9260/lib/firmware/iwlwifi-9260-th-b0-jf-b0-46.ucode
iwlwifi-firmware-iwl9000/lib/firmware/iwlwifi-9000-pu-b0-jf-b0-46.ucode
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Ray Wang [Sat, 12 Mar 2022 14:57:12 +0000 (22:57 +0800)]
ramips: add support for OrayBox X3A
OrayBox X3A is a 2.4/5GHz dual band AC router, based on MediaTek MT7621.
Specification:
* SoC: MT7621
* RAM: DDR3 128 MiB
* Flash: 16 MiB NOR (XM25Q128)
* Wi-Fi: (single chip hosting both 2.4G and 5G)
* 2.4GHz: MT7615
* 5GHz: MT7615
* Ethernet: 3x 1000Mbps
* Switch: MT7530
* LED:
* Ethernet LEDs: On the back of the router, hardware-controlled.
* Status LEDs: One "pixel-like" RGB LED in the front of the router,
which is actually made up of 3 individual LEDs (with
dedicated GPIO pins) with the color of Red, Green,
and Blue.
The OEM firmware only lights up one color at a time to
indicate status, but that's very boring, and the colors
actually look great when combined, so I've improvised a
little and made them indicate netdev activities.
My test results:
GPIO 13/14/15
000 white (actually more like bright green or cyan
because the brightness of the green LED is
higher than red and blue)
001 bright purple
010 bright green
011 red
100 bright cyan
101 blue
110 green
111 off
Flash Layout:
0x0000000-0x0030000 : "u-boot"
0x0030000-0x0040000 : "u-boot-env"
0x0040000-0x0050000 : "factory"
0x0050000-0x0f50000 : "firmware"
/*0x0f50000 to 0x0fe0000 is undefined, same as OEM firmware*/
0x0fe0000-0x0ff0000 : "bdinfo"
0x0ff0000-0x1000000 : "reserve"
MAC address:
MAC Source Description Fix
A0:CX:XX:BX:XX:0D BDINFO_9 LAN(LABEL) DTS
A0:CX:XX:BX:XX:0E BDINFO_9 + 1 WAN DTS
A2:CX:XX:BX:XX:0F FACTORY_4 WIFI2G DTS
A2:CX:XX:CX:XX:0F SETBIT 7 (FACTORY_4 + 0x100000) WIFI5G HOTPLUG
A6:CX:XX:BX:XX:0F N/A WIFI2G_CLIENT N/A
A6:DX:XX:BX:XX:0F N/A WIFI5G_CLIENT N/A
Stock dmesg:
https://pastebin.com/2t2jwLdf
Stock Dumps:
https://pastebin.com/LDLxSWX3
Installation via SSH (does not void your warranty):
1. -----UNLOCK SSH-----
1.1 Set computer IP to DHCP mode, load 'http://10.168.1.1/cgi-bin/luci' in
your browser. Password is 'admin'.
1.2 Click the "备份且导出" (backup and export) button, and download the
config file.
1.3 Open the downloaded file with 7zip, navigate to '/etc/config/'.
1.4 Edit the file './system'. Change the '0' into '1' under
"config sys 'ssh'".
1.5 Save the file.
1.6 Upload the file by clicking the "导入且恢复" (import and recover)
button. The router will automatically reboot.
2. -----FLASH THE OPENWRT FIRMWARE-----
2.1 Use any scp tool to upload the 'sysupgrade' firmware to the '/tmp/'
folder to your router. It should be root@10.168.1.1 and the password
is 'admin'.
2.2 SSH into the router, also root@10.168.1.1 and the password is 'admin'.
2.3 **IMPORTANT** Type command 'dd if=/dev/mtd3 of=/tmp/firmware.bin', to
backup the stock firmware. Since the OEM does not provide firmware
download on their website, this is the only way to get it.
2.3 **ALSO IMPORTANT** Use any scp tool to download your backed-up stock
firmware from '/tmp/' to your local drive. Then you'd better use a hex
reading tool to have a rough look at it to make sure nothing is
corrupt. Or u can just back up again and cross check the MD5.
2.4 Type command 'mtd write /tmp/XXX.bin firmware', and it should flash
the firmware.
2.5 Verify that nothing went wrong. If you're confident, type 'reboot' and
reboot the router.
Revert to stock firmware:
1. load stock firmware using mtd (make sure u have a backup).
Signed-off-by: Ray Wang <raywang777@foxmail.com>
Petr Štetiar [Sun, 17 Apr 2022 07:07:49 +0000 (09:07 +0200)]
Revert "mac80211 adjust QCA9561 PA bias"
This reverts commit
f9ff282d17ec652d63fa2404e47bb0e15ed95b69 as during
upstream patch review process nbd pointed out, that this patch needs
more work:
"The patch looks wrong to me. I'm pretty sure that AR_CH0_TOP2 is the
correct register, the definition has an explicit check for 9561 as well.
I believe this patch works by accident because it avoids writing a wrong
value to that register."
1. https://lore.kernel.org/all/
91c58969-c60e-2f41-00ac-
737786d435ae@nbd.name
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Martin Kennedy [Sat, 5 Mar 2022 19:02:36 +0000 (14:02 -0500)]
realtek: add ZyXEL GS1900-24HP v1 support
The ZyXEL GS1900-24HP v1 is a 24 port PoE switch with two SFP ports,
similar to the other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-24HP v1
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB
* RAM: Winbond W9751G8KB-25 64 MiB DDR2 SDRAM
* Ethernet: 24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps
* LEDs:
* 1 PWR LED (green, not configurable)
* 1 SYS LED (green, configurable)
* 24 ethernet port link/activity LEDs (green, SoC controlled)
* 24 ethernet port PoE status LEDs
* 2 SFP status/activity LEDs (green, SoC controlled)
* Buttons:
* 1 "RESET" button on front panel (soft reset)
* 1 button ('SW1') behind right hex grate (hardwired power-off)
* PoE:
* Management MCU: ST Micro ST32F100 Microcontroller
* 6 BCM59111 PSE chips
* 170W power budget
* Power: 120-240V AC C13
* UART: Internal populated 10-pin header ('J5') providing RS232;
connected to SoC UART through a TI or SIPEX 3232C for voltage
level shifting.
* 'J5' RS232 Pinout (dot as pin 1):
2) SoC RXD
3) GND
10) SoC TXD
Serial connection parameters: 115200 8N1.
Installation
------------
OEM upgrade method:
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware > Management
* If "Active Image" has the first option selected, OpenWrt will need to be
flashed to the "Active" partition. If the second option is selected,
OpenWrt will need to be flashed to the "Backup" partition.
* Navigate to Maintenance > Firmware > Upload
* Upload the openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-initramfs-kernel.bin
file by your preferred method to the previously determined partition.
When prompted, select to boot from the newly flashed image, and reboot
the switch.
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-squashfs-sysupgrade.bin
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs
image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-24HP v1 is a dual-partition device, you want to keep the
OEM firmware on the backup partition for the time being. OpenWrt can
only be installed in the first partition anyway (hardcoded in the
DTS). To ensure we are set to boot from the first partition, issue the
following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x81f00000 192.168.1.10:openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-squashfs-sysupgrade.bin
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
[Add info on PoE hardware to commit message]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Chukun Pan [Thu, 10 Feb 2022 13:26:40 +0000 (21:26 +0800)]
ipq806x: RT4230W: utilize nvmem-cells for ath10k caldata
Converts extraction entries from 11-ath10k-caldata into
nvmem-cells in the individual board's device-tree file.
Same as commit
2047058 ("ipq806x: utilize nvmem-cells
for pre-calibration data")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Ansuel Smith <ansuelsmth@gmail.com>
projects / openwrt / staging / rmilecki.git / log