Felix Fietkau [Tue, 7 Apr 2020 12:26:42 +0000 (14:26 +0200)]
build: fix kernel_menuconfig on macOS with newer kernel versions
Account for upstream build system changes
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Roman Hampel [Fri, 20 Mar 2020 16:32:30 +0000 (17:32 +0100)]
ath79: add support for Comfast CF-WR752AC v1
Specifications:
- Qualcomm QCA9531 + QCA9886
- dual band, antenna 2*3dBi
- Output power 50mW (17dBm)
- 1x 10/100 Mbps LAN RJ45
- 128 MB RAM / 16 MB FLASH (w25q128)
- 3 LEDs (red/green/blue)
incorporated in
"color wheel reset switch"
- UART 115200 8N1
Flashing instructions:
The U-boot bootloader contains a recovery HTTP server
to upload the firmware. Push the reset button while powering the
device on and keep it pressed for ~10 seconds. The device's LEDs will
blink several times and the recovery page will be at
http://192.168.1.1; use it to upload the sysupgrade image.
Alternatively, the original firmware is based on OpenWrt so a
sysupgrade image can be installed via the stock web GUI. Settings from
the original firmware will be saved and restored on the new one, so a
factory reset will be needed. To do so, once the new firmware is flashed,
enter into failsafe mode by pressing the reset button several times during
the boot process, until it starts flashing. Once in failsafe mode, perform
a factory reset as usual.
LED-Info:
The LEDs on the Comfast stock fw have a very proprietary behaviour,
corresponding to the user selected working mode (AP, ROUTER or REPEATER).
In the first two cases, only blue is used for status and LAN signaling. When
using the latter, blue is always off (except for sysupgrade), either red
signals bad rssi on master-link, or green good. Since the default working
mode of OpenWrt resembles that of a router/AP, the default behavior is
implemented accordingly.
MAC addresses (art partition):
location address (example) use in vendor firmware
0x0 xx:xx:xx:xx:xc:f8 -> eth0
0x6 xx:xx:xx:xx:xc:fa -> wlan5g (+2)
0x1002 xx:xx:xx:xx:xc:f9 -> not used
0x5006 xx:xx:xx:xx:xc:fb -> not used
--- xx:xx:xx:xx:xd:02 -> wlan2g (+10)
The same strange situation has already been observed and documented
for COMFAST CF-E560AC.
Signed-off-by: Roman Hampel <rhamp@arcor.de>
Co-developed-by: Joao Albuquerque <joaohccalbu@gmail.com>
Signed-off-by: Joao Albuquerque <joaohccalbu@gmail.com>
[adjust and extend commit message, rebase, minor DTS adjustments,
add correct MAC address for wmac, change RSSI LED names and behavior]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Petr Štetiar [Tue, 7 Apr 2020 08:08:16 +0000 (10:08 +0200)]
kernel: bump 5.4 to 5.4.31
Refreshed patches, removed upstreamed patches:
oxnas: 003-ARM-dts-oxnas-Fix-clear-mask-property.patch
generic: 184-USB-serial-option-add-Wistron-Neweb-D19Q1.patch
Run tested: apu2, qemu-x86-64, apalis
Build tested: sunxi/a53, imx6, x86/64, ipq40xx
Tested-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> [apu2]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Bjørn Mork [Sat, 4 Apr 2020 11:04:51 +0000 (13:04 +0200)]
kernel: generic: 5.4: fix mips command line parameter patch
Fixing a build error when CONFIG_KERNEL_KEXEC is enabled:
make[5]: Entering directory '/home/bjorn/tmp/tmp-lede/build_dir/target-mipsel_24kc_musl/linux-ramips_mt7621/linux-5.4.28'
CALL scripts/checksyscalls.sh
CALL scripts/atomic/check-atomics.sh
CHK include/generated/compile.h
CC arch/mips/kernel/machine_kexec.o
arch/mips/kernel/machine_kexec.c: In function 'kexec_nonboot_cpu_jump':
arch/mips/kernel/machine_kexec.c:268:27: error: 'relocate_new_kernel_size' undeclared (first use in this function); did you mean 'kexec_relocate_new_kernel_end'?
reboot_code_buffer + relocate_new_kernel_size);
^~~~~~~~~~~~~~~~~~~~~~~~
kexec_relocate_new_kernel_end
arch/mips/kernel/machine_kexec.c:268:27: note: each undeclared identifier is reported only once for each function it appears in
arch/mips/kernel/machine_kexec.c: In function 'kexec_reboot':
arch/mips/kernel/machine_kexec.c:306:27: error: 'relocate_new_kernel_size' undeclared (first use in this function); did you mean 'kexec_relocate_new_kernel_end'?
reboot_code_buffer + relocate_new_kernel_size);
^~~~~~~~~~~~~~~~~~~~~~~~
kexec_relocate_new_kernel_end
make[7]: *** [scripts/Makefile.build:266: arch/mips/kernel/machine_kexec.o] Error 1
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Linus Walleij [Mon, 30 Mar 2020 21:28:11 +0000 (23:28 +0200)]
gemini: Refine package list
The NAS packages for Gemini doesn't even include the
block-mount package. Augment the list to be based off
the DEFAULT_PACKAGES.nas to make sure we extend on the
essentials.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Norbert van Bolhuis [Fri, 3 Apr 2020 16:12:46 +0000 (18:12 +0200)]
linux-atm: Include linux/sockios.h for SIOCGSTAMP
Since linux kernel commit
0768e17073dc527ccd18ed5f96ce85f9985e9115
(2019-04-19) the asm-generic/sockios.h header no longer defines
SIOCGSTAMP. Instead it provides only SIOCGSTAMP_OLD.
The linux/sockios.h header now defines SIOCGSTAMP using either
SIOCGSTAMP_OLD or SIOCGSTAMP_NEW as appropriate. This linux only
header file is not included so we get a build failure.
Signed-off-by: Norbert van Bolhuis <nvbolhuis@aimvalley.nl>
Ansuel Smith [Sat, 4 Apr 2020 18:41:02 +0000 (20:41 +0200)]
ipq806x: switch to 5.4 kernel
ipq806x has been tested for a lot and lots of people reported good results.
Switch the main kernel to 5.4 following the other targets.
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq8065, NBG6817]
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Florian Eckert [Tue, 7 Apr 2020 12:03:50 +0000 (14:03 +0200)]
base-files: add enabled commands to service rc.common
Add missing enbaled command help output.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Alexey Dobrovolsky [Wed, 8 Apr 2020 18:43:36 +0000 (21:43 +0300)]
ramips: use full 8MB flash on ZyXEL Keenetic
ZyXEL Keenetic has 8MB flash, but OpenWrt uses only 4MB.
This commit fixes the problem.
WikiDevi page [1] says that ZyXEL Keenetic has FLA1: 8 MiB, there is
an article with specs [2] (in Russian).
[1] https://wikidevi.wi-cat.ru/ZyXEL_Keenetic
[2] https://3dnews.ru/608774/page-2.html
Fixes: FS#2487
Fixes: a7cbf59e0e04 ("ramips: add new device ZyXEL Keenetic as kn")
Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
Adrian Schmutzler [Tue, 7 Apr 2020 10:31:48 +0000 (12:31 +0200)]
ath79: fix MAC addresses for ethernet on ZyXEL NBG6716
MAC addresses of the ethernet devices (eth0 & eth1) are randomly set at
boot time by the ag71xx driver, because it is currently not possible to
retrieve MAC addresses in ASCII format within the DTS file.
This commit works around this behaviour by setting the MAC addresses
during the preinit phase.
The same has been implemented recently for the Siemens WS-AP3610 in
d2b8ccb1c04d ("ath79: add support for Siemens WS-AP3610").
MAC assignment in vendor firmware is as follows:
use vendor address OpenWrt
2g wifi0 ethaddr -> wlan1
5g wifi1 ethaddr +1 -> wlan0
lan eth1 ethaddr +2 -> eth0
wan eth0 ethaddr +3 -> eth1
ethaddr is retrieved by $(mtd_get_mac_ascii u-boot-env ethaddr)
Note that both Wifi and ethernet indexing is swapped in OpenWrt
compared to vendor firmware.
Suggested-by: Guillaume Lefebvre <guillaume@zelig.ch>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Kevin Gagnon <kevin_gagnon@videotron.ca>
Pawel Dembicki [Thu, 19 Apr 2018 07:20:58 +0000 (09:20 +0200)]
ramips: add support for D-Link DWR-960
The DWR-960 Wireless Router is based on the MT7620A SoC.
Specification:
- MediaTek MT7620A (580 Mhz)
- 128 MB of RAM
- 16 MB of FLASH
- 1x 802.11bgn radio
- 1x 802.11ac radio (MT7610 mpcie card)
- 4x 10/100 Mbps Ethernet (1 WAN and 3 LAN)
- 1x 10/100/1000 Mbps Ethernet (1 LAN) (AR8035)
- 2x internal, non-detachable antennas (Wifi 2.4G)
- 3x external, detachable antennas (2x LTE, 1x Wifi 5G)
- 1x LTE modem
- UART (J4) header on PCB (57600 8n1)
- 9x LED, 2x button
- JBOOT bootloader
Known issues:
- Flash is extremely slow.
Installation:
Apply factory image via http web-gui or JBOOT recovery page
How to revert to OEM firmware:
- push the reset button and turn on the power. Wait until LED start
blinking (~10sec.)
- upload original factory image via JBOOT http (IP: 192.168.123.254)
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Pawel Dembicki [Wed, 25 Mar 2020 06:08:37 +0000 (07:08 +0100)]
packages: mt76: add 14c3:7610 pci id to list
This commit add patch with 14c3:7610 pci id addition.
It was sent upstream.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[bumped PKG_RELEASE]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Pawel Dembicki [Tue, 24 Mar 2020 05:23:49 +0000 (06:23 +0100)]
ramips: mt7620: add rgmii delays support
At this moment mt7620 ethernet driver doesn't support rgmii delays
configuration. SoC MT7620 have bits 2 and 3 in GPC1 an GPC2 to configure
delays for rx and tx rgmii interface.
This patch adds rx/tx rgmii delay configuration from dts.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Pawel Dembicki [Thu, 19 Apr 2018 07:08:38 +0000 (09:08 +0200)]
generic: backport Wistron Neweb D19Q1 patches
Backport patches which adds suport for the Wistron Neweb D19Q1 3G/4G modem,
used in D-Link DWR-960.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Adrian Schmutzler [Tue, 7 Apr 2020 08:34:33 +0000 (10:34 +0200)]
ramips: mt7621: harmonize naming scheme for Mikrotik
So far, image/device/board names for Mikrotik devices in mt7621 have
been used quite inconsistently.
This patch harmonizes the naming scheme by applying the same style
as used lately in ath79, i.e. using "RouterBOARD" as separate word
in the model name (instead of RB prefix for the number) and deriving
the board/device name from that (= make lower case and replace spaces
by hyphens).
This style has already been used for most the model/DEVICE_MODEL
variables in mt7621, so this is essentially just adjusting the remaining
variables to that.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tobias Schramm [Wed, 8 Apr 2020 10:47:15 +0000 (12:47 +0200)]
ramips: mt7621: reenable rbm11g
I have a rbm11g and can confirm that the LAN port is indeed
switch port 0.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Tobias Schramm [Wed, 8 Apr 2020 10:47:14 +0000 (12:47 +0200)]
ramips: mt7621: add label mac address to rbm11g
The rbm11g has a label with printed on mac address similar to the
rbm33g.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Rosen Penev [Tue, 7 Apr 2020 02:15:59 +0000 (19:15 -0700)]
iproute2: add kmod-netlink-diag for ss
Allows proper usage of the ss tool. Otherwise, several errors and bad
data gets thrown:
Cannot open netlink socket: Protocol not supported
Cannot open netlink socket: Protocol not supported
Cannot open netlink socket: Protocol not supported
Cannot open netlink socket: Protocol not supported
Cannot open netlink socket: Protocol not supported
Cannot open netlink socket: Protocol not supported
Cannot open netlink socket: Protocol not supported
Originally reported here: https://github.com/openwrt/packages/issues/8232
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Tue, 7 Apr 2020 02:15:58 +0000 (19:15 -0700)]
kmod: add netlink-diag package
This is used by the ss utility from iproute2.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
INAGAKI Hiroshi [Sat, 23 Mar 2019 13:45:42 +0000 (22:45 +0900)]
ramips: add support for Buffalo WSR-2533DHPL
Buffalo WSR-2533DHPL is a 2.4/5 GHz band 11ac router, based on MediaTek
MT7621A.
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 128 MiB
- Flash : SPI-NOR 16 MiB
- WLAN : 2.4/5 GHz 4T4R (2x MediaTek MT7615N)
- Ethernet : 10/100/1000 Mbps
- Switch : MediaTek MT7530 (SoC)
- LED/keys : 8x/6x (3x buttons, 2x slide-switches)
- UART : through-hole on PCB
- J4: 3.3V, GND, TX, RX from triangle-mark
- 57600n8
- Power : 12VDC 1.5A
Flash instruction using initramfs image:
1. prepare the TFTP server with the initramfs image renamed to
"linux.trx-recovery" and IP address "192.168.11.2"
2. press the "AOSS" button while powering on the WSR-2533DHPL
3. after 10 seconds, release the "AOSS" button, WSR-2533DHPL downloads
the initramfs image and boot with it automatically
4. on the initramfs image, download the sysupgrade image to the device
and perform sysupgrade with it
5. wait ~120 seconds to complete flashing
Switch position overview:
- slide-switch1 (2x positions)
- "AUTO"
- "MANUAL" (not connected to gpio)
- slide-switch2 (3x positions)
- "ROUTER"
- "AP" (not connected to gpio)
- "WB"
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[add note on switches, fix group->groups for state_default]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Dan Haab [Mon, 6 Apr 2020 23:14:39 +0000 (16:14 -0700)]
bcm53xx: add support for Luxul FullMAC WiFi devices
This prepares support for models XAP-1610 and XWR-3150. Flashing
requires using Luxul firmware version:
1) 8.1.0 or newer for XAP-1610
2) 6.4.0 or newer for XWR-3150
and uploading firmware using "Firmware Update" web UI page.
Signed-off-by: Dan Haab <dan.haab@legrand.com>
Chris Morgan [Wed, 11 Mar 2020 21:00:42 +0000 (16:00 -0500)]
ath79: add support for Comfast CF-EW72
Specifications:
Qualcomm/Atheros QCA9531 + QCA9886
2x 10/100 Mbps Ethernet, with 48v PoE
2T2R 2.4 GHz, 802.11b/g/n
2T2R 5 GHz, 802.11a/n/ac
128MB RAM
16MB SPI Flash
4x LED (Always On Power, LAN, WAN, WLAN)
Flashing Instructions:
Original firmware is based on OpenWRT, so flashing the sysupgrade image on
the factory firmware is sufficient.
Tested: Reset button, WAN LED, LAN LED, Power LED (always on, not much
to test), WLAN LED (one LED only for 2 interfaces, by default it gets
assigned to the first interface), MAC addresses (match factory firmware).
My LAN factory MAC address ends in F2.
use stock_mac art_loc
lan :f2 0x0
wan :f3 0x1002
5g :f4 0x6
2g :f5 0x5006
Since MAC address flash locations do not really match their use in vendor
firmware (e.g. address from 5 GHz calibration data is assigned to 2.4 GHz
WiFi), just calculate the MAC addresses with an offset based on 0x0 address.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
[add MAC address comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Hans Dedecker [Sun, 5 Apr 2020 20:26:33 +0000 (22:26 +0200)]
ppp: update to version 2.4.8.git-2020-03-21
Use upstream latest git HEAD as it allows to remove the patches
700-radius-Prevent-buffer-overflow-in-rc_mksid,
701-pppd-Fix-bounds-check-in-EAP-code and
702-pppd-Ignore-received-EAP-messages-when-not-doing-EAP and
take in other fixes.
41a7323 pppd: Fixed spelling 'unkown' => 'unknown' (#141)
6b014be pppd: Print version information to stdout instead of stderr (#133)
cba2736 pppd: Add RFC1990 (Multilink) to the See Also section of the man page
f2f9554 pppd: Add mppe.h to the list of headers to install if MPPE is defined
ae54fcf pppd: Obfuscate password argument string
8d45443 pppd: Ignore received EAP messages when not doing EAP
8d7970b pppd: Fix bounds check in EAP code
858976b radius: Prevent buffer overflow in rc_mksid()
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Rosen Penev [Sun, 5 Apr 2020 22:38:32 +0000 (15:38 -0700)]
tools/cmake: update to 3.17.0
Remove libressl patches; they are no longer needed as LibreSSl adde
support
Replace qt tests patch with one that disables all of them.
Refresh remaining one.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Alex Lewontin [Fri, 21 Feb 2020 20:57:44 +0000 (15:57 -0500)]
ramips: harmonize Netgear R6120 DT LED node names
This changes the node names for the LEDs in the Netgear R6120
device-tree file to provide consistency with other devices.
Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
[improve commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tan Zien [Sun, 5 Apr 2020 03:15:44 +0000 (11:15 +0800)]
kernel: netdev: add missing config for mlx5 driver
The mlk5 kmod lacks all necessary build symbols
for kernel 4.14 (again).
Add missing symbols to avoid build failure on these targets.
Signed-off-by: Tan Zien <nabsdh9@gmail.com>
[rewrite commit message - reorder symbols]
Signed-off-by: David Bauer <mail@david-bauer.net>
Lim Guo Wei [Sat, 4 Apr 2020 19:52:26 +0000 (03:52 +0800)]
ath79: add support for TP-Link TL-MR3420 v3
This adds support for the TP-Link TL-MR3420 v3, a later revision of the
v2 with an external gpiochip similar to TP-Link Archer C7 v4.
Specifications:
SOC: Qualcomm Atheros QCA9531
CPU: 650MHz
Flash: 4 MiB
RAM: 32 MiB
WLAN: Qualcomm Atheros QCA9531 bgn 2T2R 2.4 GHz
Ethernet: 5 ports (100M)
Flashing instructions:
- Flash factory image from OEM WebUI:
openwrt-ath79-tiny-tplink_tl-mr3420-v3-squashfs-factory.bin
- Sysupgrade from ath79 image:
openwrt-ath79-tiny-tplink_tl-mr3420-v3-squashfs-sysupgrade.bin
Signed-off-by: Lim Guo Wei <limguowei@gmail.com>
[remove SUPPORTED devices, some typo adjustments, fix WAN MAC
address, fix sorting in 01_leds]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Kevin Darbyshire-Bryant [Sun, 5 Apr 2020 16:22:20 +0000 (17:22 +0100)]
dnsmasq: bump to 2.81rc5
Bump to 2.81rc5 and re-work ipset-remove-old-kernel-support.
More runtime kernel version checking is done in 2.81rc5 in various parts
of the code, so expand the ipset patch' scope to inlude those new areas
and rename to something a bit more generic.:wq
Upstream changes from rc4
532246f Tweak to DNSSEC logging.
8caf3d7 Fix rare problem allocating frec for DNSSEC.
d162bee Allow overriding of ubus service name.
b43585c Fix nameserver list in auth mode.
3f60ecd Fixed resource leak on ubus_init failure.
0506a5e Handle old kernels that don't do NETLINK_NO_ENOBUFS.
e7ee1aa Extend stop-dns-rebind to reject IPv6 LL and ULA addresses. We also reject the loopback address if rebind-localhost-ok is NOT set.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Adrian Schmutzler [Wed, 1 Apr 2020 19:54:58 +0000 (21:54 +0200)]
ipq806x: remove support for kernel 4.14
This target has been on kernel 4.19 for several months [1] and
already uses kernel 5.4 as testing kernel. Therefore, it should
not be necessary to keep support for kernel 4.14 as well.
[1]
2a82e0e1ca0f ("ipq806x: switch to 4.19 kernel version")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq8065/nbg6817]
Kip Porterfield [Fri, 3 Apr 2020 21:59:23 +0000 (21:59 +0000)]
ramips: add DTS triggers to USB LEDs for F9K1109v1
Alter DTS for Belkin F9K1109v1 to trigger USB leds from the echi/ochi
ports.
Signed-off-by: Kip Porterfield <kip.porterfield@gmail.com>
John Crispin [Sun, 5 Apr 2020 14:10:38 +0000 (16:10 +0200)]
mediatek: set v5.4 as default
Signed-off-by: John Crispin <john@phrozen.org>
John Crispin [Fri, 3 Apr 2020 15:51:59 +0000 (17:51 +0200)]
mediatek: add hw flow table offloading
Signed-off-by: John Crispin <john@phrozen.org>
John Crispin [Fri, 3 Apr 2020 15:42:44 +0000 (17:42 +0200)]
mediatek: add support for rtl8367c
Signed-off-by: John Crispin <john@phrozen.org>
John Crispin [Fri, 3 Apr 2020 09:54:12 +0000 (11:54 +0200)]
mediatek: drop v4.14 support
Signed-off-by: John Crispin <john@phrozen.org>
John Crispin [Fri, 3 Apr 2020 09:52:35 +0000 (11:52 +0200)]
mediatek: more v5.4 fixes
These are all backports and/or on their way upstream.
Signed-off-by: John Crispin <john@phrozen.org>
John Crispin [Fri, 3 Apr 2020 09:49:42 +0000 (11:49 +0200)]
mediatek: consolidate partition names and settings
Signed-off-by: John Crispin <john@phrozen.org>
John Crispin [Fri, 3 Apr 2020 09:18:26 +0000 (11:18 +0200)]
mediatek: fix elecom board name
menuconfig was showing the the company name twice.
Signed-off-by: John Crispin <john@phrozen.org>
John Crispin [Mon, 6 Apr 2020 05:04:38 +0000 (07:04 +0200)]
generic: fix flow table hw offload
Make the driver work with recent upstream changes.
Signed-off-by: John Crispin <john@phrozen.org>
Peter Stadler [Fri, 27 Mar 2020 12:36:08 +0000 (13:36 +0100)]
netifd: fix 14_migrate-dhcp-release script
prepend 'uci' to 'commit network'
Signed-off-by: Peter Stadler <peter.stadler@student.uibk.ac.at>
Chuanhong Guo [Sun, 5 Apr 2020 07:52:49 +0000 (15:52 +0800)]
ramips: fix path for dma-ralink and mtk-hsdma
These two drivers were available in drivers/staging in 5.4.
Fix driver paths for them.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Kevin Darbyshire-Bryant [Mon, 30 Sep 2019 09:41:28 +0000 (10:41 +0100)]
dropbear: backport add ip address to exit without auth messages
201e359 Handle early exit when addrstring isn't set
fa4c464 Improve address logging on early exit messages (#83)
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Kevin Darbyshire-Bryant [Sat, 4 Apr 2020 11:42:13 +0000 (12:42 +0100)]
hostapd: Move hostapd variants to WirelessAPD menu
It seemed very confusing when trying to select the different variants of
hostapd which are somewhat scattered about under the menu 'Network'.
Moving all hostapd variants under a common submenu helps avoid
confusion.
Inspired-by: Kevin Mahoney <kevin.mahoney@zenotec.net>
[Fixup badly formatted patch, change menu name]
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Kevin Darbyshire-Bryant [Sun, 5 Apr 2020 08:14:43 +0000 (09:14 +0100)]
umdns: update to the version 2020-04-05
ab7a39a umdns: fix unused error
45c4953 dns: explicitly endian-convert all fields in header and question
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Chuanhong Guo [Sat, 4 Apr 2020 13:23:50 +0000 (21:23 +0800)]
Revert "generic: 5.4: Add 4B_OPCODES flag to w25q256"
This reverts commit
d7f21940bcaf70ba404d354c7fa6519c1717d00a.
Winbond W25Q256FV and W25Q256JV both uses 0xef4019 as JEDEC ID,
but only the latter has proper 4B_OPCODES support.
W25Q256FV has all 4B read instructions but it lacks a 4B page program
instruction, causing the entire flash to be read-only.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Tan Zien [Sat, 4 Apr 2020 04:02:40 +0000 (12:02 +0800)]
kernel: Fix miss config and module for mlx driver
Missing config symbols could lead to build failures on kernel
4.14/4.19.
Signed-off-by: Tan Zien <nabsdh9@gmail.com>
[rephrase commit message - reorder symbols]
Signed-off-by: David Bauer <mail@david-bauer.net>
Kevin Darbyshire-Bryant [Sat, 4 Apr 2020 08:20:08 +0000 (09:20 +0100)]
umdns: suppress address-of-packed-member warning
gcc 8 & 9 appear to be more picky with regards access alignment to
packed structures, leading to this warning in dns.c:
dns.c:261:2: error: converting a packed ‘struct dns_question’ pointer
(alignment 1) to a ‘uint16_t’ {aka ‘short unsigned int’} pointer
(alignment 2) may result in an unaligned pointer value
[-Werror=address-of-packed-member]
261 | uint16_t *swap = (uint16_t *) q;
Work around what I think is a false positive by turning the warning off.
Not ideal, but not quite as not ideal as build failure.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Kevin Darbyshire-Bryant [Thu, 2 Apr 2020 18:30:17 +0000 (19:30 +0100)]
treewide: convert sed -r to posix -E
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Thibaut VARÈNE [Wed, 18 Mar 2020 09:35:26 +0000 (10:35 +0100)]
ath79: improve mikrotik-caldata.sh
Reduce unnecessary flash wear and be tidy:
- Run the extraction only if necessary
- Extract temporary file to /tmp
- cleanup after execution
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
INAGAKI Hiroshi [Mon, 30 Mar 2020 06:19:50 +0000 (15:19 +0900)]
kernel: rtl8367b: use id as a bit offset for BYPASS_LINE_RATE
In RTL8367B (RTL8367RB/RTL8367R-VB), the driver in GPL tars of the
devices with this switch directly uses the ID of external interface
as a bit offset.
We should use the same way.
ref (RTL8367B):
- ASUS RT-N56U
- TP-Link Archer C2 v1
ref (RTL8367):
- TP-Link TL-WR2543ND v1
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
INAGAKI Hiroshi [Sat, 28 Mar 2020 10:31:23 +0000 (19:31 +0900)]
kernel: rtl8367b: fix DEBUG register address for extif2
RTL8367B_CHIP_DEBUG1_REG (0x1304) is for external interface 1. For
external interface 2, use RTL8367B_CHIP_DEBUG2_REG (0x13e2) instead.
Fixes: 9801d61c4a ("kernel: rtl8367b: add configuration for extif2")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Chuanhong Guo [Sat, 4 Apr 2020 08:30:16 +0000 (16:30 +0800)]
ramips: mt7621: bringup dsa master on preinit
DSA requires master netdev to be up before any of its slave ports.
Bring it up during preinit so that the first lan port can be used
on failsafe.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Sat, 4 Apr 2020 07:20:46 +0000 (15:20 +0800)]
ramips: mt7621: disable image for mikrotik_rbm11g
It's unknown which switch port is used on mikrotik_rbm11g.
Disable this image until someone with actual device fixes this problem.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Sat, 4 Apr 2020 04:44:28 +0000 (12:44 +0800)]
ramips: remove set_preinit_iface script
This script isn't suitable for mt7621 anymore due to switching to DSA
and it needs a different preinit script.
Generic preinit logic in package/base-files has the ability to parse
board.json and pick preinit iface accordingly. Just remove this script
instead of moving it into subtargets.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
DENG Qingfang [Sat, 4 Apr 2020 04:10:32 +0000 (12:10 +0800)]
generic: mt7530: fix null pointer dereferencing in port5 setup
The 2nd gmac of mediatek soc ethernet may not be connected to a PHY
and a phy-handle isn't always available.
Unfortunately, mt7530 dsa driver assumes that the 2nd gmac is always
connected to switch port 5 and setup mt7530 according to phy address
of 2nd gmac node, causing null pointer dereferencing when phy-handle
isn't defined in dts.
This commit fix this setup code by checking return value of
of_parse_phandle before using it.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
DENG Qingfang [Fri, 3 Apr 2020 14:57:15 +0000 (22:57 +0800)]
generic: backport support for MT7530 DSA port mirroring
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
René van Dorst [Wed, 1 Apr 2020 08:01:20 +0000 (10:01 +0200)]
ramips: correct MTC WR1201 LAN ports names
LAN ports of MTC WR1201 are reversed, so correct their names
Signed-off-by: René van Dorst <opensource@vdorst.com>
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
DENG Qingfang [Wed, 1 Apr 2020 03:19:12 +0000 (11:19 +0800)]
ramips: mt7621: add new NAND driver
Add new NAND driver for MT7621
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
DENG Qingfang [Thu, 26 Mar 2020 15:14:05 +0000 (23:14 +0800)]
ramips: mt7621: drop obsolete mx25l25635f dts hack
5.4 kernel has fixed this issue, so the hack is no longer needed.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
DENG Qingfang [Wed, 1 Apr 2020 08:42:08 +0000 (16:42 +0800)]
Revert "ramips: mt7621: disable images for gehua_ghl-r-001"
This reverts commit
28080d54d217fb4ab112e079f69462fee695dbf8.
Support for MX25L25635F flash is fixed upstream
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
DENG Qingfang [Thu, 26 Mar 2020 14:00:48 +0000 (22:00 +0800)]
ramips: move swconfig to subtargets except for MT7621
As MT7621 does not use swconfig anymore, move the package swconfig to
other subtargets.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
DENG Qingfang [Tue, 24 Mar 2020 12:09:10 +0000 (20:09 +0800)]
ramips: mt7621: introduce 'soc_device' initialization
mt7621 SoC has its own 'ralink_soc_info' structure with some
information about the soc itself. Pcie controller and pcie phy
drivers for this soc which are still in staging git tree make uses
of 'soc_device_attribute' looking for revision 'E2' in order to
know if reset lines are or not inverted. This way of doing things
seems to be necessary in order to make things clean and properly.
Hence, introduce this 'soc_device' to be able to properly use those
attributes in drivers. Also set 'data' pointer points to the struct
'ralink_soc_info' to be able to export also current soc information
using this mechanism.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
DENG Qingfang [Thu, 19 Mar 2020 16:26:08 +0000 (00:26 +0800)]
ramips: fix MikroTik 750Gr3 LAN ports names
They are labeled as LAN2..LAN5 instead of LAN1..LAN4
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
DENG Qingfang [Thu, 19 Mar 2020 11:43:39 +0000 (19:43 +0800)]
ramips: use SoC I2C instead of bitbanged for Ubiquiti ER-X-SFP
The original idea of bitbanged I2C is to use i2c-gpio-custom
Since i2c-gpio-custom is no longer available on 5.4, use SoC I2C instead
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
DENG Qingfang [Thu, 19 Mar 2020 11:33:27 +0000 (19:33 +0800)]
ramips: mt7621: fix Ubiquiti ER-X ports names and MAC addresses
The name of each user port should be eth0..4, instead of lan1..4
and there is no WAN port. Rename them to match the official firmware.
To avoid conflict with the master port (gmac0), rename it to "dsa".
The official firmware assigns MAC address in this way:
eth0 = label mac
eth1 = label mac + 1
...
eth4 = label mac + 4
Since we have switched to DSA, it's possible to use different MAC for each port.
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
DENG Qingfang [Tue, 10 Mar 2020 17:33:40 +0000 (01:33 +0800)]
ramips: mt7621: net-label support
Add support for renaming ethernet interfaces in DTS
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
DENG Qingfang [Sun, 1 Mar 2020 09:17:49 +0000 (17:17 +0800)]
ramips: mt7621: switch kernel version to 5.4
After all dts and config changes, 4.14 no longer works on mt7621.
Switch it to 5.4 directly.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
DENG Qingfang [Wed, 18 Mar 2020 17:10:50 +0000 (01:10 +0800)]
ramips: mt7621: change default ramips_setup_interfaces configuration
Most of MT7621 boards have LAN1~4 and WAN, so make this as the default
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
DENG Qingfang [Sat, 4 Apr 2020 06:52:12 +0000 (14:52 +0800)]
ramips: mt7621 remove unused pinctrl groups in dts
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[split commit, remove leftover uart3->gpio setup]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
DENG Qingfang [Wed, 18 Mar 2020 15:38:58 +0000 (23:38 +0800)]
ramips: mt7621: update dts/defconfig for DSA
update dts and network/LED configuration for DSA driver.
sysupgrade from images prior to this commit with config preserved
will cause broken ethernet setup.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Acked-by: Jo-Philipp Wich <jo@mein.io>
[split commit]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
DENG Qingfang [Tue, 17 Mar 2020 12:54:34 +0000 (20:54 +0800)]
ramips: mt7621: backport GPIO driver fix
Backport 2 patches from linux-next to fix mt7621 GPIO driver
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
DENG Qingfang [Wed, 1 Apr 2020 15:14:33 +0000 (23:14 +0800)]
ramips: mt7621: update PCIe node in dtsi
Update PCIe node in dtsi to match the new driver
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
DENG Qingfang [Wed, 11 Mar 2020 13:05:41 +0000 (21:05 +0800)]
ramips: mt7621: backport PCIe driver fixes from staging-test
Backport mt7621-pci/mt7621-pci-phy fixes from staging-test
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
DENG Qingfang [Fri, 13 Mar 2020 13:27:03 +0000 (21:27 +0800)]
ramips: mt7621: update pinctrl nodes
Upstream GPIO driver uses "groups" "function" properties
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
DENG Qingfang [Tue, 3 Mar 2020 21:22:24 +0000 (05:22 +0800)]
ramips: mt7621: convert GPIO dts refs
The upstream driver does not use &gpio0..2 banks notation anymore,
so convert them to &gpio
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
DENG Qingfang [Sun, 1 Mar 2020 09:14:44 +0000 (17:14 +0800)]
ramips: mt7621: replace gpio/eth nodes in mt7621.dtsi
There's different gpio and ethernet drivers upstream for mt7621.
Update these two nodes to match upstream dt bindings.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
DENG Qingfang [Sun, 1 Mar 2020 09:11:06 +0000 (17:11 +0800)]
ramips: mt7621: refresh kernel config
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
DENG Qingfang [Sun, 1 Mar 2020 09:06:45 +0000 (17:06 +0800)]
ramips: refresh patches
Removed upstreamed/solved elsewhere upstream:
- 0001-MIPS-ralink-Add-rt3352-SPI_CS1-pinmux.patch
- 0002-MIPS-pci-rt2880-set-pci-controller-of_node.patch
- 0004-MIPS-ralink-add-MT7621-pcie-driver.patch
- 0009-PCI-MIPS-enable-PCIe-on-MT7688.patch
- 0025-pinctrl-ralink-add-pinctrl-driver.patch
- 0028-GPIO-ralink-add-mt7621-gpio-controller.patch
- 0043-spi-add-mt7621-support.patch
- 0045-i2c-add-mt7621-driver.patch
- 0047-DMA-ralink-add-rt2880-dma-engine.patch
- 0053-mtd-spi-nor-add-w25q256-3b-mode-switch.patch
- 0054-mtd-spi-nor-w25q256-respect-default-mode.patch
- 0099-pci-mt7620.patch
- 304-spi-nor-enable-4B-opcodes-for-mx25l25635f.patch
Removed because of the new NAND driver:
- 0038-Revert-mtd-nand-Remove-unused-chip-write_page-hook.patch
- 0039-mtd-add-mt7621-nand-support.patch
- 0040-nand-hack.patch
Remove patch that no longer applies (needs rework):
- 0034-NET-multi-phy-support.patch
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
DENG Qingfang [Fri, 17 Jan 2020 08:04:14 +0000 (16:04 +0800)]
ramips: mtk-mmc: set correct DMA mask
Since commit
f8c55dc ("MIPS: use generic dma noncoherent ops for
simple noncoherent platforms") changed MIPS dma handling, the mmc
driver fails because it doesn't have a dma mask is set.
So set the correct dma mask.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
DENG Qingfang [Sun, 1 Mar 2020 09:02:06 +0000 (17:02 +0800)]
ramips: move MTK MMC driver to files directory
Move MTK MMC driver from "files-4.14" to "files" so kernel 5.4
can use it
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
DENG Qingfang [Sun, 1 Mar 2020 09:01:09 +0000 (17:01 +0800)]
ramips: copy patches and kernel config to 5.4
Copy patches and kernel config to 5.4 for ramips
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Rafał Miłecki [Fri, 3 Apr 2020 13:55:01 +0000 (15:55 +0200)]
bcm53xx: refactor board.d code in 02_network
1. Use functions for cleaner code
2. Always execute WAN interface generic code
Before this change WAN interface code wasn't executed on all devices due
to an early "exit 0".
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Tan Zien [Sun, 5 Jan 2020 21:16:43 +0000 (05:16 +0800)]
kernel: add module for Mellanox mlx Network Driver
add module to support Mellanox Connect-X card
mlx4 supports ConnectX-3 series and previous cards
mlx5 supports Connect-IB/ConnectX-4 series and later cards
Signed-off-by: Tan Zien <nabsdh9@gmail.com>
Tim Harvey [Wed, 1 Apr 2020 17:23:12 +0000 (10:23 -0700)]
imx6: bootscript: use partition UUID for rootfs if possible
Specifying root filesystem by device is non-deterministic for several
reasons:
- USB device unmeration order is not garunteeed for USB storage devs
- MMC devs ordering is determined by the instance of the MMC host
controller including non-storage SDIO devices which can throw off
numbering depending on kernel versions.
It is recommended to use partition UUID
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Wed, 1 Apr 2020 17:24:12 +0000 (10:24 -0700)]
octeontx: switch to kernel 5.4
5.4 is stable on Gateworks Newport GW610x/GW620x/GW630x/GW640x
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Paul Spooren [Thu, 12 Mar 2020 22:55:41 +0000 (12:55 -1000)]
build: refactor JSON info files to `profiles.json`
JSON info files contain machine readable information of built profiles
and resulting images. These files were added in commit
881ed09ee6e2
("build: create JSON files containing image info").
They are useful for firmware wizards and script checking for
reproducibility.
Currently all JSON files are stored next to the built images, resulting
in up to 168 individual files for the ath79/generic target.
This patch refactors the JSON creation to store individual per image
(not per profile) files in $(BUILD_DIR)/json_info_files and create an
single overview file called `profiles.json` in the target directory.
Storing per image files and not per profile solves the problem of
parallel file writes. If a profiles sysupgrade and factory image are
finished at the same time both processes would write to the same JSON
file, resulting in randomly broken outputs.
Some target like x86/64 do not use the image code yet, resulting in
missing JSON files. If no JSON info files were created, no
`profiles.json` files is created as it would be empty anyway.
As before, this creation is enabled by default only if `BUILDBOT` is set.
Tested via buildroot & ImageBuilder on ath79/generic, imx6 and x86/64.
Signed-off-by: Paul Spooren <mail@aparcar.org>
[json_info_files dir handling in Make, if case refactoring]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Kevin Darbyshire-Bryant [Wed, 1 Apr 2020 21:44:37 +0000 (22:44 +0100)]
grub2: fix build when ASLR enabled
Disable ASLR and filter '-fno-plt' from CFLAGS: solves building when
ASLR enabled by basically disabling ASLR.
Solves errors similar to:
relocation R_X86_64_32S against `.rodata' can not be used when making a PIE object; recompile with -fPIE
or
module missing GLOBAL_OFFSET_TABLE
Suggested-by: 李国 <uxgood.org@gmail.com>
Acked-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Kevin Darbyshire-Bryant [Mon, 29 Jul 2019 15:54:02 +0000 (16:54 +0100)]
kmod-sched-cake: switch to in-tree cake for 4.19+
Use in tree version of cake for kernels 4.19+ and backport features from
later kernel versions to 4.19.
Unfortunately PROVIDES dependency handling produces bogus circular
dependency warnings so whilst this package and kmod-sched-cake-oot
should be able to PROVIDE kmod-sched-cake this doesn't work.
Instead, remove the PROVIDES option and modify package sqm-scripts to
depend on the correct module independently.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Kevin Darbyshire-Bryant [Mon, 30 Mar 2020 17:52:09 +0000 (18:52 +0100)]
kmod-sched-cake: rename to kmod-sched-cake-oot
In preparation for dropping the out of tree cake module and using
in tree cake from upstream, rename the package to kmod-sched-cake-oot
(out of tree)
Initially add a PROVIDES kmod-sched-cake so that package dependencies
can be satisfied.
Ultimately this package will be removed when linux 4.14 is removed.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Jason A. Donenfeld [Wed, 1 Apr 2020 20:08:42 +0000 (14:08 -0600)]
wireguard: bump to 1.0.
20200401
Recent backports to 5.5 and 5.4 broke our compat layer. This release is
to keep things running with the latest upstream stable kernels.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Daniel Golle [Mon, 30 Mar 2020 22:35:04 +0000 (23:35 +0100)]
mac80211: rt2x00: prune more unnecessary exports
The calibration patches for MT7620 unnecessarily export symbols and
populate never accessed function pointers. Remove all that and make
functions static as the only place where each of those functions is
called is within rt2800lib.c.
Also make code more readable by fixing indentation, removing
unnecessary parantheses and simplifying some instructions using
shorthands here and there.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Kevin Darbyshire-Bryant [Tue, 31 Mar 2020 12:01:18 +0000 (13:01 +0100)]
jansson: convert to cmake
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Eneas U de Queiroz [Tue, 31 Mar 2020 20:51:45 +0000 (17:51 -0300)]
openssl: bump to 1.1.1f
There were two changes between 1.1.1e and 1.1.1f:
- a change in BN prime generation to avoid possible fingerprinting of
newly generated RSA modules
- the patch reversing EOF detection we had already applied.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Daniel Golle [Sat, 28 Mar 2020 21:55:31 +0000 (21:55 +0000)]
oxnas: some improvements for Shuttle KD20
* install kmod-hwmon-drivetemp by default
* wire up thermal zone
* fix fan GPIO polarity
* fix i2c-gpio GPIO_OPEN_DRAIN
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Tue, 31 Mar 2020 19:27:11 +0000 (20:27 +0100)]
oxnas: fix warning in SATA driver
drivers/ata/sata_oxnas.c: In function 'sata_oxnas_port_irq':
drivers/ata/sata_oxnas.c:2126:25: warning: left shift count >= width of type [-Wshift-count-overflow]
if (ap->qc_active & (1 << ATA_TAG_INTERNAL)) {
^~
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Petr Štetiar [Tue, 31 Mar 2020 14:03:55 +0000 (16:03 +0200)]
ipq40xx: fix DAP-2610 boot failure
Albert has reported, that his DAP-2610 wont boot with the latest
snapshot and Fredrik has found out, that the device gets stuck at
"Waiting for root device ..." due to missing 5.4 kernel config symbol
CONFIG_MTD_SPLIT_WRGG_FW which was probably lost during the kernel
version bump.
Ref: https://forum.openwrt.org/t/dap-2610-bricked-help-needed
Fixes: 272e0a702a2b ("ipq40xx: add v5.4 support")
Suggested-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
李国 [Fri, 27 Mar 2020 11:16:26 +0000 (19:16 +0800)]
x86/64: add cdrom and iso9660 drivers
The iso image need cdrom and iso9660 drivers to boot, otherwise it will
hang when mounting the root file system
Signed-off-by: 李国 <uxgood.org@gmail.com>
李国 [Thu, 26 Mar 2020 06:05:33 +0000 (14:05 +0800)]
x86: generate EFI platform bootable images
Add EFI platform bootable images for x86 platforms. These images can
also boot from legacy BIOS platform.
EFI System Partition need to be fat12/fat16/fat32 (not need to load
filesystem drivers), so the first partition of EFI images are not ext4
filesystem any more.
GPT partition table has an alternate partition table, we did not
generate it. This may cause problems when use these images as qemu disk
(kernel can not find rootfs), we pad enough sectors will be ok.
Signed-off-by: 李国 <uxgood.org@gmail.com>
[part_magic_* refactoring, removed genisoimage checks]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
李国 [Thu, 26 Mar 2020 05:51:32 +0000 (13:51 +0800)]
grub2: make some change to add efi platform support
1.generate boot image at Package/install section
2.move boot image to $(STAGING_DIR_IMAGE)/grub2/
3.add efi variant to support efi platform
Signed-off-by: 李国 <uxgood.org@gmail.com>
李国 [Thu, 26 Mar 2020 05:47:40 +0000 (13:47 +0800)]
firmware-utils: ptgen: add GPT support
Add GPT support to ptgen, so we can generate EFI bootable images.
Introduced two options:
-g generate GPT partition table
-G GUID use GUID for disk and increase last bit for all partitions
We drop The alternate partition table to reduce size, This may cause
problems when generate vmdk images or vdi images. We have to pad enough
sectors when generate these images.
Signed-off-by: 李国 <uxgood.org@gmail.com>
[fixed compilation on macOS]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Álvaro Fernández Rojas [Tue, 31 Mar 2020 11:22:59 +0000 (13:22 +0200)]
bcm27xx-gpu-fw: update to latest version from RPi foundation
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
projects / openwrt / staging / neocturne.git / log