Hauke Mehrtens [Sun, 20 Oct 2024 21:54:56 +0000 (23:54 +0200)]
uclient: update to Git HEAD (2024-06-27)
e035d57 uclient-fetch: improve error handling
a220818 uclient-fetch: add support for --header cmdline argument
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sun, 20 Oct 2024 21:50:39 +0000 (23:50 +0200)]
ubus: update to Git HEAD (2024-10-20)
65bb027 CMakeLists.txt: bump minimum cmake version
252a9b0 libubus: Make UBUS_* macros work cleanly in C++
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sun, 20 Oct 2024 21:48:34 +0000 (23:48 +0200)]
procd: update to Git HEAD (2024-10-20)
0f88a52 system: replace openwrt_release with os-release
ef3ab8b system: add build date to ubus output
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sun, 20 Oct 2024 21:45:33 +0000 (23:45 +0200)]
iwinfo: update to Git HEAD (2024-10-20)
c97bcc2 devices: add device ID for Ralink RT5592
b94f066 devices: add device id for MediaTek MT7925E
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Florian Eckert [Thu, 20 Oct 2022 08:02:45 +0000 (10:02 +0200)]
base-files: add SOURCE_DATE_EPOCH as OPENWRT_BUILD_DATE to os-release
This commit adds the build date during compilation to the os-release file.
This information can then be used later to output this via the the ubus,
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Link: https://github.com/openwrt/openwrt/pull/15987
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Christian Marangi [Thu, 17 Oct 2024 13:54:52 +0000 (15:54 +0200)]
airoha: Introduce EN7581 SoC support
Introduce EN7581 SoC support with currently rfb board supported.
This is a new 64bit SoC from Airoha that is currently almost fully
supported upstream with only the DTS missing. Setting source-only
waiting for the full upstream support to be completed.
Link: https://github.com/openwrt/openwrt/pull/16730
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Thu, 17 Oct 2024 18:26:05 +0000 (20:26 +0200)]
generic: backport alloc_netdev_dummy patch from upstream
Backport alloc_netdev_dummy patch from upstream needed for new Airoha
EN7581 SoC.
Refresh all affected patch with make target/linux/refresh.
Link: https://github.com/openwrt/openwrt/pull/16730
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Christian Marangi [Thu, 17 Oct 2024 13:42:51 +0000 (15:42 +0200)]
airoha: move en7523 in dedicated subtarget
In preparation for EN7581 SoC support, move en7523 in dedicated
subtarget.
This is needed as EN7581 is now 64bit but en7523 is 32bit hence have
very different kernel config.
Also rename patch to a more friendly number sequence.
Link: https://github.com/openwrt/openwrt/pull/16730
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Priit Laes [Fri, 8 Jan 2021 11:28:47 +0000 (13:28 +0200)]
ath79: add support for COMFAST CF-E355AC v2
COMFAST CF-E355AC v2 is a ceiling mount AP with PoE support,
based on Qualcomm/Atheros QCA9531 + QCA9886.
Short specification:
- 1x 10/100 Mbps Ethernet, with PoE support (wan/eth1)
- 1x 10/100/1000 Mbps Ethernet, with PoE support (lan/eth0)
- 128MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, 802.11b/g/n (wlan2g)
- 2T2R 5 GHz, 802.11ac/n/a, WAVE 2 (wlan5g)
- built-in 4x 3 dBi antennas
- output power (max): 500 mW (27 dBm)
- 1x RGB LED, 1x button
- separate watchdog chip via GPIO (bottom of PCB?)
- UART header on PCB with proper labelling
Markings on PCB:
* R121QH_VER2.1 (silkscreen, bottom)
* CF-WA800 (sticker, top)
Initial flashing instructions:
Original firmware is based on OpenWrt.
a) Use sysupgrade image directly in vendor GUI.
b) Or via tftp:
ipaddr=192.168.1.1
serverip=192.168.1.10
bootfile="firmware.bin"
c) Or possibly via u-boot's `httpd` command.
MAC-address mapping follows original firmware:
* eth1 (wan) is the lowest mac address (art @ 0x0)
* eth0 (lan) uses eth1 + 1 (art @ 0x1002)
* wlan2g (phy1) uses eth1 + 2 (art @ 0x06)
* wlan5g (phy0) uses eth1 + 10 (not present in art)
* unused MAC (eth1 + 3) (art @ 0x5006)
Art dump (`hexdump /dev/mtd1 |grep ZZZZ`):
0000000 ZZZZ XXXX XXX0 ZZZZ XXXX XXX2 ffff ffff
0001000 0202 ZZZZ XXXX XXX1 0000 0000 0000 0000
0005000 202f bd21 0101 ZZZZ XXXX XXX3 0000 2000
Root access to original firmware (only via UART) can be achieved by
making a backup of configuration from web interface. Backup contains
whole `/etc` directory...
Signed-off-by: Priit Laes <plaes@plaes.org>
Link: https://github.com/openwrt/openwrt/pull/16556
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Paul Donald [Sun, 7 Apr 2024 12:23:57 +0000 (14:23 +0200)]
dnsmasq: gate configdir usage behind absolute path check
don't use configuration directories which are relative
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14975
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Paul Donald [Tue, 26 Mar 2024 23:43:41 +0000 (00:43 +0100)]
dnsmasq: add handling of `dns-rr` to init script (add arbitrary resource records)
Add support for handling of DNS RR (Resource Records) requests, which
are needed for the HTTPS Type 65 records, introduced to support the
DNS-based Service Discovery (DNS-SD) mechanism for HTTPS services and
defined in the RFC 9460 (9.1. Query Names for HTTPS RRs).
Ref: https://forum.openwrt.org/t/resolving-query-type-65-to-local-address-for-ios-clients-in-dnsmasq/179504/11
uci config usage:
config dnsrr
option rrname 'foo.example.com'
option rrnumber '65'
option hexdata '00'
hexdata is optional.
Available since dnsmasq 2.62 (for around 12 years at this point).
Note: dnsmasq dns-rr are not affected by filter-rr
Tested on 22.03.5
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Tested-by: Vladimir Kochkovski <ask@getvladimir.com>
Link: https://github.com/openwrt/openwrt/pull/14975
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Paul Donald [Mon, 1 Apr 2024 18:18:14 +0000 (20:18 +0200)]
dnsmasq: quoted path variables
Prevents problems when variables contain spaces.
Tested on: 23.05.3
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14975
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Paul Donald [Sat, 6 Apr 2024 17:44:19 +0000 (19:44 +0200)]
dnsmasq: add 'extraconftext' parameter
Users can now freely add new dnsmasq parameters (i.e. a whole config)
via extraconf. This means users can add their own parameters without
changes to init or GUI.
Co-opted the default of confdir also to include the instance name.
This way each instance gets its own .d directory (and separate instances
do not all inherit the same 'extraconftext').
Usage:
config dnsmasq 'config'
...
option extraconftext 'cache-size=2048\nlog-async=20'
config dnsmasq 'blah'
...
option extraconftext 'cache-size=128\nlog-async=5'
or even (which would produce staggered output but still valid)
config dnsmasq 'blah'
...
option extraconftext 'cache-size=128
log-async=5'
See https://forum.openwrt.org/t/add-dnsmasq-custom-options-field-in-luci-gui/193184
Tested on: 23.05.3, 22.03.6
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Tested-by: Vladimir Kochkovski <ask@getvladimir.com>
Link: https://github.com/openwrt/openwrt/pull/14975
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Paul Donald [Tue, 26 Mar 2024 23:44:05 +0000 (00:44 +0100)]
dnsmasq: add handling of `cache-rr` to init script
dnsmasq v2.90 introduced `--cache-rr=<rrtype>[,<rrtype>...]`.
uci config usage:
config dnsmasq
...
option cache_rr 'AAAA,CNAME,NXDOMAIN,SRV,...'
The dnsmasq instance internally builds a linked list of RR to cache
from the individually supplied parameters, so it's allowed to provide
multiples:
... --cache-rr=AAAA --cache-rr=A ...
See https://forum.openwrt.org/t/resolving-query-type-65-to-local-address-for-ios-clients-in-dnsmasq/179504
Tested on: 23.05.2
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Tested-by: Vladimir Kochkovski <ask@getvladimir.com>
Link: https://github.com/openwrt/openwrt/pull/14975
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Paul Donald [Tue, 2 Apr 2024 01:16:02 +0000 (03:16 +0200)]
dnsmasq: add handling of `filter-rr` to init script
dnsmasq v2.90 introduced `--filter-rr=<rrtype>[,<rrtype>...]`.
uci config usage:
config dnsmasq
...
option filter_rr 'AAAA,CNAME,NXDOMAIN,SRV,...'
The dnsmasq instance internally builds a linked list of RR to filter
from the individually supplied parameters, so it's harmless to provide
synonyms:
... --filter-A --filter-rr=A ...
See https://forum.openwrt.org/t/resolving-query-type-65-to-local-address-for-ios-clients-in-dnsmasq/179504/23
Tested on: 23.05.2
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Tested-by: Vladimir Kochkovski <ask@getvladimir.com>
Link: https://github.com/openwrt/openwrt/pull/14975
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rany Hany [Fri, 6 Sep 2024 10:25:24 +0000 (10:25 +0000)]
hostapd: add support for SAE in PPSK option
This patch allows the use of SAE when using PPSK after
https://w1.fi/cgit/hostap/commit/?id=
fcbdaae8a52e542705a651ee78b39b02935fda20
added support for it.
It also implements a fix so that this option works with SAE. The reason this
doesn't work out of the box is because OpenWRT deviates from hostapd defaults
by setting `sae_pwe` option to 2 which makes this mode not function properly
(results in every auth attempt being denied).
That issue was addressed by not overriding hostapd's default for the `sae_pwe`
option when the PPSK option is in use. This should be fine because hostapd's
test cases specifically test this mode with the default SAE parameters. See:
https://w1.fi/cgit/hostap/commit/?id=
c34b35b54e81dbacd9dee513b74604c87f93f6a3
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/16343
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Felix Fietkau [Sun, 20 Oct 2024 16:43:17 +0000 (18:43 +0200)]
kernel: fix forwarding broadcast packets between vlan-on-dsa and non-dsa netdevs
Fix conditions for handling offloaded packets
Fixes: #13430
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Chris Jones [Sat, 19 Oct 2024 20:50:54 +0000 (21:50 +0100)]
ipq40xx: make GL.iNet A1300 switch functional
Set the physical switch to KEY_RFKILL, since its previous value
(KEY_SETUP) is unsupported. This should also make the KEY_RESET button
functional, by allowing the gpio-button-hotplug kmod to load.
Signed-off-by: Chris Jones <cmsj@tenshu.net>
Link: https://github.com/openwrt/openwrt/pull/16564
Signed-off-by: Robert Marko <robimarko@gmail.com>
Rosen Penev [Sun, 22 Sep 2024 17:41:24 +0000 (10:41 -0700)]
kernel: gpio-nct5104d: use devm
Allows removal of the remove function by letting devm handle everything.
Avoids gotos as well.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16507
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rosen Penev [Sat, 19 Oct 2024 22:15:09 +0000 (15:15 -0700)]
apm821xx: bring back AT803X_PHY
AT803X_PHY was replaced with QCA83XX_PHY which handles external switches.
But for internal ones like in the Meraki MR24, AT803X_PHY is needed.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16737
Signed-off-by: Robert Marko <robimarko@gmail.com>
Rosen Penev [Fri, 27 Sep 2024 00:35:34 +0000 (17:35 -0700)]
ramips: modernize snd-mt7620 driver
Use more devm and remove gotos.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16631
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 19 Oct 2024 21:51:38 +0000 (23:51 +0200)]
firmware-utils: update to Git HEAD (2024-10-16)
0cfd104 zytrx: add ZyXEL LTE7490-M904
3d09357 asusuimage: new tool for creating TRX-images compatible with AsusWRT
f35781f asusuimage: fix compile error with old GCC release
26c7f05 nec-usbatermfw: add tool for NEC "USB ATERM" format
ed9c97f tplink-safeloader: bump EAP610-V3 compat_level
5192cf9 mktplinkfw2: Add 16Mmtk layout
ca444f1 tplink-safeloader: add support for cpe710-v2
88fbd52 bcmclm: support printing channels
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 19 Oct 2024 21:50:38 +0000 (23:50 +0200)]
tools: firmware-utils: update to Git HEAD (2024-10-16)
5192cf9 mktplinkfw2: Add 16Mmtk layout
ca444f1 tplink-safeloader: add support for cpe710-v2
88fbd52 bcmclm: support printing channels
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rosen Penev [Mon, 27 Nov 2023 19:40:48 +0000 (11:40 -0800)]
ath79: aruba,ap115: use nvmem
Userspace handling is deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16284
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Shiji Yang [Thu, 10 Oct 2024 10:29:06 +0000 (18:29 +0800)]
ipq40xx: dts: disable qpic_bam for EMMC and SPI Flash devices
The qpic DMA controller is used by the parallel NAND Flash
interface. We don't need to enable it when nand-controller node
is marked as disabled.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16654
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Priit Laes [Fri, 11 Oct 2024 07:15:22 +0000 (10:15 +0300)]
ramips: mt7621: mikrotik rb760igs: Include "hEX S" in model name
Mikrotik seems to prefer "hEX S" as general name for this model,
therefore include this in devicetree model name as well.
Signed-off-by: Priit Laes <plaes@plaes.org>
Link: https://github.com/openwrt/openwrt/pull/16658
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rosen Penev [Sat, 28 Sep 2024 00:20:37 +0000 (17:20 -0700)]
realtek: use more devm
Simplifies probe slightly.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16650
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Stefan Kalscheuer [Sat, 12 Oct 2024 09:08:50 +0000 (11:08 +0200)]
uboot-mvebu: update to version 2024.10
Update package to the latest stable version and drop upstreamed patches:
0001-arm-mvebu-turris_omnia-Enable-LTO-by-default-on-Turr.patch
100-mvebu-armada-8k-respect-CONFIG_DISTRO_DEFAULTS.patch
Other patches automatically refreshed (line numbers only)
Add custom config flags to disable building efimkcapsule by default.
This introduces a dependency to GnuTLS which is not present and we do
not need it here.
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
Link: https://github.com/openwrt/openwrt/pull/16676
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tianling Shen [Sat, 12 Oct 2024 08:16:58 +0000 (16:16 +0800)]
sdk: bundle libraries for llvm toolchain
This allows the llvm toolchain to be executed on different host.
Also add it to strip list.
Fixes: 0ac0840088d5 ("sdk: ship llvm toolchain")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16674
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rodrigo B. de Sousa Martins [Wed, 25 Sep 2024 18:35:20 +0000 (15:35 -0300)]
iptables: backport "nft: track each register individually" from 1.9
From the upstream repo:
Instead of assuming only one register is used, track all 16 regs
individually.
This avoids need for the 'PREV_PAYLOAD' hack and also avoids the need to
clear out old flags:
When we see that register 'x' will be written to, that register state is
reset automatically.
Existing dissector decodes
ip saddr 1.2.3.4 meta l4proto tcp
... as
-s 6.0.0.0 -p tcp
iptables-nft -s 1.2.3.4 -p tcp is decoded correctly because the expressions
are ordered like:
meta l4proto tcp ip saddr 1.2.3.4
|
... and 'meta l4proto' did clear the PAYLOAD flag.
The simpler fix is:
ctx->flags &= ~NFT_XT_CTX_PAYLOAD;
in nft_parse_cmp(), but that breaks dissection of '1-42', because
the second compare ('cmp lte 42') will not find the
payload expression anymore.
This commit fixes #11169 and openwrt/packages#22727, and potentially anyone that uses iptables-nft legacy support.
Signed-off-by: Rodrigo B. de Sousa Martins <rodrigo.sousa.577@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16504
[Added patch header]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rosen Penev [Fri, 27 Sep 2024 00:22:29 +0000 (17:22 -0700)]
ramips: cleanup ralink SPI driver
Increase usage of devm to get rid of goto and _remove.
Get rid of hw_reset_count. It's not really used for anything.
Use dev_err_probe to handle potential EPROBE_DEFER.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16588
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rosen Penev [Tue, 8 Oct 2024 23:39:07 +0000 (16:39 -0700)]
mediatek: leds-smartrg: handle disabled LEDs
If LEDs are disabled, they should not be handled.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16651
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rosen Penev [Tue, 8 Oct 2024 23:37:08 +0000 (16:37 -0700)]
mediatek: leds-smartrg: use devm_mutex_init
No longer need normal _remove function. Replaced with _disable.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16651
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Til Kaiser [Sun, 29 Sep 2024 14:56:26 +0000 (16:56 +0200)]
x86: add Gowin 1U Rack Mount Router Server
There are three variants of that board:
--- Hardware Highlights ---
GW-BS-1UR1-10G:
- CPU: Intel® Alder Lake N100 quad-core 3.4GHz
- RAM: 16GB DDR5 4800MHz
- Storage: Onboard 128GB eMMC, 2x NVME slots, 2x SATA slots
- Ports: 2x 2.5G, 2x 1G, 1x POE, 2x 10G SFP+, 1x RJ45 Serial Port
- WIFI: 1x M.2 slot
- 4G/5G: 1x M.2 slot
- USB: 2x 3.0, 2x 2.0
- Button: 1x Power Button
- Video: 1x HDMI, 1x VGA
- LEDs: 4x
GW-BS-1UR2-10G:
- CPU: Intel® Core™ i3-N305 octa-core 3.8GHz
- RAM: 32GB DDR5 4800MHz
- Storage: Onboard 128GB eMMC, 2x NVME slots, 2x SATA slots
- Ports: 2x 2.5G, 2x 1G, 1x POE, 2x 10G SFP+, 1x RJ45 Serial Port
- WIFI: 1x M.2 slot
- 4G/5G: 1x M.2 slot
- USB: 2x 3.0, 2x 2.0
- Button: 1x Power Button
- Video: 1x HDMI, 1x VGA
- LEDs: 4x
GW-BS-1UR2-25G:
- CPU: Intel® Core™ i3-N305 octa-core 3.8GHz
- RAM: 32GB DDR5 4800MHz
- Storage: Onboard 128GB eMMC, 2x NVME slots, 2x SATA slots
- Ports: 2x 2.5G, 2x 1G, 1x POE, 2x 25G SFP+, 1x RJ45 Serial Port
- WIFI: 1x M.2 slot
- 4G/5G: 1x M.2 slot
- USB: 2x 3.0, 2x 2.0
- Button: 1x Power Button
- Video: 1x HDMI, 1x VGA
- LEDs: 4x
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/16560
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Til Kaiser [Sun, 29 Sep 2024 14:55:57 +0000 (16:55 +0200)]
base-files: add ucidef_set_network_device_path_port function
The already existing uci function ucidef_set_network_device_path
can be used to specify a unique PCI address to name a network interface.
However, I noticed that some NIC ports share the same PCI address
but are still distinguishable by the dev_port value of the network
interface's sysfs entry.
This commit adds a new uci function ucidef_set_network_device_path_port,
which is similar to ucidef_set_network_device_path but takes an
additional argument where the user can specify the dev_port value.
The internal function preinit_config_port loops through
all network interfaces at the given PCI address and chooses the one
where the dev_port value matches.
This was tested on an x86_64 device using a Mellanox ConnectX-3 card.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/16560
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Til Kaiser [Sun, 29 Sep 2024 14:54:54 +0000 (16:54 +0200)]
kernel: modules: add boot flag to igc, mlx4, and mlx5 drivers
Set the boot flag for the igc, mlx4-core, and mlx5-core network device drivers
to load them at a more early stage of the boot process.
This is required for network drivers whose network interface PCI paths are set
via ucidef_set_network_device_path inside the 02_network script since it is
called after kernel modules are loaded from modules-boot.d but before they are
loaded from the modules.d directory.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/16560
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rosen Penev [Fri, 10 May 2024 22:55:25 +0000 (15:55 -0700)]
mwlwifi: fix compilation with 6.6 and 64-bit
Upstream patch updated to fix kernel 6.6 compilation. It was also split
up into 5. Do the same here.
The patches are taken from this upstreasm PR:
https://github.com/kaloz/mwlwifi/pull/413
Renamed other patches so as to not overlap.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15452
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
INAGAKI Hiroshi [Sat, 29 Jun 2024 12:57:23 +0000 (21:57 +0900)]
ath79: add support for NEC Aterm WG1800HP2
NEC Aterm WG1800HP2 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on
QCA9558.
Specification:
- SoC : Qualcomm Atheros QCA9558
- RAM : DDR2 128 MiB (2x Nanya NT5TU32M16DG-AC)
- Flash : SPI-NOR 16 MiB (Macronix MX25L12845EMI-10G)
- WLAN : 2.4/5 GHz
- 2.4 GHz : 3T3R (Qualcomm Atheros QCA9558 (SoC))
- 5 GHz : 3T3R (Qualcomm Atheros QCA9880)
- Ethernet : 5x 10/100/1000 Mbps
- switch : Atheros AR8327
- LEDs/Keys (GPIO) : 12x/5x
- UART : through-hole on PCB
- assignment : 3.3V, GND, NC, TX, RX from tri-angle marking
- settings : 9600n8
- USB : 1x USB 2.0 Type-A
- hub (internal) : NEC uPD720114
- Power : 12 VDC, 1.5 A (Max. 17 W)
- Stock OS : NetBSD based
Flash instruction using initramfs-factory.bin image (StockFW WebUI):
1. Boot WG1800HP2 with router mode normally
2. Access to the WebUI ("http://aterm.me/" or "http://192.168.0.1/") on
the device and open firmware update page ("ファームウェア更新")
3. Select the OpenWrt initramfs-factory.bin image and click update
("更新") button
4. After updating, the device will be rebooted and booted with OpenWrt
initramfs image
5. On the initramfs image, upload (or download) uboot.bin and
sysupgrade.bin image to the device
6. Replace the bootloader with a uboot.bin image
mtd write <uboot.bin image> bootloader
7. Perform sysupgrade with a sysupgrade.bin image
sysupgrade <sysupgrade image>
8. Wait ~120 seconds to complete flashing
Flash instruction using initramfs-factory.bin image (bootloader CLI):
1. Connect and open serial console
2. Power on WG1800HP2 and interrupt bootloader by ESC key
3. Login to the bootloader CLI with a password "chiron"
4. Start TFTP server by "tftpd" command
5. Upload initramfs-factory.bin via tftp from your computer
example (Windows): tftp -i 192.168.0.1 PUT initramfs-factory.bin
6. Boot initramfs image by "boot" command
7. On the initramfs image, back up the stock bootloader and firmware if
needed
8. Upload (or download) uboot.bin and sysupgrade.bin image to the device
9. Replace the bootloader with a uboot.bin image
10. Perform sysupgrade with a sysupgrade.bin image
11. Wait ~120 seconds to complete flashing
Notes:
- All LEDs are connected to the TI TCA6416A (marking: PH416A) I2C
Expander chip.
- The stock bootloader requires an unknown filesystem on firmware area
in the flash. Booting of OpenWrt from that filesystem cannot be
handled, so the bootloader needs to be replaced to mainline U-Boot
before OpenWrt installation.
MAC addresses:
LAN : A4:12:42:xx:xx:44 (config, 0x6 (hex))
WAN : A4:12:42:xx:xx:45 (config, 0xc (hex))
2.4 GHz: A4:12:42:xx:xx:46 (config, 0x0 (hex))
5 GHz : A4:12:42:xx:xx:47 (config, 0x12 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16297
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
INAGAKI Hiroshi [Sat, 29 Jun 2024 12:53:42 +0000 (21:53 +0900)]
ath79: add support for NEC Aterm WG1800HP
NEC Aterm WG1800HP is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on
QCA9558.
Specification:
- SoC : Qualcomm Atheros QCA9558
- RAM : DDR2 128 MiB (2x Nanya NT5TU32M16DG-AC)
- Flash : SPI-NOR 16 MiB (Macronix MX25L12845EMI-10G)
- WLAN : 2.4/5 GHz
- 2.4 GHz : 3T3R (Qualcomm Atheros QCA9558 (SoC))
- 5 GHz : 3T3R (Qualcomm Atheros QCA9880)
- Ethernet : 5x 10/100/1000 Mbps
- switch : Atheros AR8327
- LEDs/Keys (GPIO) : 12x/5x
- UART : through-hole on PCB
- assignment : 3.3V, GND, NC, TX, RX from tri-angle marking
- settings : 9600n8
- USB : 1x USB 2.0 Type-A
- hub (internal) : NEC uPD720114
- Power : 12 VDC, 1.5 A (Max. 17 W)
- Stock OS : NetBSD based
Flash instruction using initramfs-factory.bin image (StockFW WebUI):
1. Boot WG1800HP with router mode normally
2. Access to the WebUI ("http://aterm.me/" or "http://192.168.0.1/") on
the device and open firmware update page ("ファームウェア更新")
3. Downgrade the stock firmware to v1.0.2
4. After downgrading, select the OpenWrt initramfs-factory.bin image and
click update ("更新") button
5. After updating, the device will be rebooted and booted with OpenWrt
initramfs image
6. On the initramfs image, upload (or download) uboot.bin and
sysupgrade.bin image to the device
7. Replace the bootloader with a uboot.bin image
mtd write <uboot.bin image> bootloader
8. Perform sysupgrade with a sysupgrade.bin image
sysupgrade <sysupgrade image>
9. Wait ~120 seconds to complete flashing
Flash instruction using initramfs-factory.bin image (bootloader CLI):
1. Connect and open serial console
2. Power on WG1800HP and interrupt bootloader by ESC key
3. Login to the bootloader CLI with a password "chiron"
4. Start TFTP server by "tftpd" command
5. Upload initramfs-factory.bin via tftp from your computer
example (Windows): tftp -i 192.168.0.1 PUT initramfs-factory.bin
6. Boot initramfs image by "boot" command
7. On the initramfs image, back up the stock bootloader and firmware if
needed
8. Upload (or download) uboot.bin and sysupgrade.bin image to the device
9. Replace the bootloader with a uboot.bin image
10. Perform sysupgrade with a sysupgrade.bin image
11. Wait ~120 seconds to complete flashing
Notes:
- All LEDs are connected to the TI TCA6416A (marking: PH416A) I2C
Expander chip.
- The stock bootloader requires an unknown filesystem on firmware area
in the flash. Booting of OpenWrt from that filesystem cannot be
handled, so the bootloader needs to be replaced to mainline U-Boot
before OpenWrt installation.
- The data length of blocks in firmware image will be checked
(4M < threshold < 6M) on the stock WebUI on some versions (v1.0.28,
v1.0.30(latest), ...), so needs to be downgraded before OpenWrt
installation with initramfs-factory image.
MAC addresses:
LAN : 10:66:82:xx:xx:04 (config, 0x6 (hex))
WAN : 10:66:82:xx:xx:05 (config, 0xc (hex))
2.4 GHz: 10:66:82:xx:xx:06 (config, 0x0 (hex))
5 G : 10:66:82:xx:xx:07 (config, 0x12 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16297
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
INAGAKI Hiroshi [Sat, 2 Mar 2019 17:48:18 +0000 (02:48 +0900)]
ath79: add support for NEC Aterm WG1400HP
NEC Aterm WG1400HP is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on
QCA9558.
Specification:
- SoC : Qualcomm Atheros QCA9558
- RAM : DDR2 128 MiB (2x Nanya NT5TU32M16DG-AC)
- Flash : SPI-NOR 16 MiB (Macronix MX25L12845EMI-10G)
- WLAN : 2.4/5 GHz
- 2.4 GHz : 3T3R (Qualcomm Atheros QCA9558 (SoC))
- 5 GHz : 2T2R (Qualcomm Atheros QCA9882)
- Ethernet : 5x 10/100/1000 Mbps
- switch : Atheros AR8327
- LEDs/Keys (GPIO) : 12x/5x
- UART : through-hole on PCB
- assignment : 3.3V, GND, NC, TX, RX from tri-angle marking
- settings : 9600n8
- USB : 1x USB 2.0 Type-A
- hub (internal) : NEC uPD720114
- Power : 12 VDC, 1.5 A (Max. 17 W)
- Stock OS : NetBSD based
Flash instruction using initramfs-factory.bin image (StockFW WebUI):
1. Boot WG1400HP with router mode normally
2. Access to the WebUI ("http://aterm.me/" or "http://192.168.0.1/") on
the device and open firmware update page ("ファームウェア更新")
3. Select the OpenWrt initramfs-factory.bin image and click update
("更新") button
4. After updating, the device will be rebooted and booted with OpenWrt
initramfs image
5. On the initramfs image, upload (or download) uboot.bin and
sysupgrade.bin image to the device
6. Replace the bootloader with a uboot.bin image
mtd write <uboot.bin image> bootloader
7. Perform sysupgrade with a sysupgrade.bin image
sysupgrade <sysupgrade image>
8. Wait ~120 seconds to complete flashing
Flash instruction using initramfs-factory.bin image (bootloader CLI):
1. Connect and open serial console
2. Power on WG1400HP and interrupt bootloader by ESC key
3. Login to the bootloader CLI with a password "chiron"
4. Start TFTP server by "tftpd" command
5. Upload initramfs-factory.bin via tftp from your computer
example (Windows): tftp -i 192.168.0.1 PUT initramfs-factory.bin
6. Boot initramfs image by "boot" command
7. On the initramfs image, back up the stock bootloader and firmware if
needed
8. Upload (or download) uboot.bin and sysupgrade.bin image to the device
9. Replace the bootloader with a uboot.bin image
10. Perform sysupgrade with a sysupgrade.bin image
11. Wait ~120 seconds to complete flashing
Notes:
- All LEDs are connected to the TI TCA6416A (marking: PH416A) I2C
Expander chip.
- The stock bootloader requires an unknown filesystem on firmware area
in the flash. Booting of OpenWrt from that filesystem cannot be
handled, so the bootloader needs to be replaced to mainline U-Boot
before OpenWrt installation.
MAC addresses:
LAN : 10:66:82:xx:xx:20 (config, 0x6 (hex))
WAN : 10:66:82:xx:xx:21 (config, 0xc (hex))
2.4 GHz: 10:66:82:xx:xx:22 (config, 0x0 (hex))
5 GHz : 10:66:82:xx:xx:23 (config, 0x12 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16297
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
INAGAKI Hiroshi [Thu, 27 Jun 2024 15:53:31 +0000 (00:53 +0900)]
ath79: commonize SGMII calibration functions of QCA955x in lzma-loader
Commonize function names of SGMII calibration functions of QCA955x added
for Meraki MR18, to use them for NEC Aterm series based on QCA9558 as
well.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16297
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
INAGAKI Hiroshi [Thu, 27 Jun 2024 06:51:34 +0000 (15:51 +0900)]
ath79: add missing usb-phy-analog reset to usb phys for QCA955x
Add missing reset bits of USB phys on QCA955x SoCs to qca955x.dtsi to
handle them.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16297
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
INAGAKI Hiroshi [Sat, 31 Aug 2024 08:59:41 +0000 (17:59 +0900)]
uboot-ath79: refresh patches
Refresh patches by "make package/uboot-ath79/prepare" and manual
adjustments.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16297
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
INAGAKI Hiroshi [Sat, 31 Aug 2024 08:46:54 +0000 (17:46 +0900)]
uboot-ath79: add support for NEC Aterm series based on QCA9558
Add support for NEC Aterm series devices based on QCA9558.
The following devices have almost the same hardware, so the same U-Boot
binary can be used for them.
- NEC Aterm WG1400HP
- NEC Aterm WG1800HP
- NEC Aterm WG1800HP2
By the way, on NetBSD-based NEC Aterm devices, only 0x20000 (128KiB) is
available for a bootloader on the flash chip and that limitation is too
small for mainline U-Boot with the default options. So many
features/commands not required for booting OpenWrt and recoverying are
disabled on that devices, like the followings.
- networking support
- FIT support
- all decompression methods support
etc...
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16297
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
INAGAKI Hiroshi [Sat, 31 Aug 2024 08:42:53 +0000 (17:42 +0900)]
uboot-ath79: add initial support for QCA955x SoCs
Add initial support for Qualcomm Atheros QCA955x series SoCs.
This support was based on the QCA956x support, QSDK, GPL tar of TP-Link
Archer C5 v1.20.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16297
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Stefan Lippers-Hollmann [Thu, 17 Oct 2024 15:37:02 +0000 (17:37 +0200)]
mac80211: realtek: rtlwifi: add RTL8192DU support
Add Realtek RTL8192DU support to the rtlwifi package.
The RTL8192DU chipset is a 802.11a/b/g/n chip which supports 2.4 and 5 GHz at
up to 40 MHz channel bandwidth, three hardware variations exist:
* single MAC/ single PHY
* single MAC/ double PHY
* double MAC/ double PHY
This driver has been successully tested on a single MAC/ single PHY variant
0bda:8194 (DeLock 88540, https://www.delock.com/produkt/88540/merkmale.html)
rtl_usb: rx_max_size 15360, rx_urb_num 8, in_ep 1
rtl8192du: Driver for Realtek RTL8192DU WLAN interface
rtl8192du: Loading firmware file rtlwifi/rtl8192dufw.bin
ieee80211 phy0: Selected rate control algorithm 'rtl_rc'
usbcore: registered new interface driver rtl8192du
Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* monitor
* mesh point
* P2P-client
* P2P-GO
interface combinations are not supported
The new rtlwifi based driver rtl8192du has been merged in kernel v6.11.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16721
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Stefan Lippers-Hollmann [Thu, 17 Oct 2024 15:31:58 +0000 (17:31 +0200)]
linux-firmware: add firmware for Realtek RTL8192DU
This commit packages the newly merged firmware (v39.0) for Realtek RTL8192DU
802.11a/b/g/n USB wireless cards.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16721
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Stefan Lippers-Hollmann [Thu, 17 Oct 2024 15:30:47 +0000 (17:30 +0200)]
linux-firmware: Update to version
20241017
This updates the following firmware files:
amdgpu/gc_11_5_2_imu.bin
amdgpu/gc_11_5_2_me.bin
amdgpu/gc_11_5_2_mec.bin
amdgpu/gc_11_5_2_mes1.bin
amdgpu/gc_11_5_2_mes_2.bin
amdgpu/gc_11_5_2_pfp.bin
amdgpu/gc_11_5_2_rlc.bin
amdgpu/psp_14_0_4_ta.bin
amdgpu/psp_14_0_4_toc.bin
amdgpu/sdma_6_1_2.bin
amdgpu/vpe_6_1_3.bin
ath12k/QCN9274/hw2.0/board-2.bin
ath12k/QCN9274/hw2.0/firmware-2.bin
ath12k/QCN9274/hw2.0/Notice.txt
brcm/brcmfmac4354-sdio.nvidia,p2371-2180.txt
cirrus/cs35l54-b0-dsp1-misc-
103c8d85-amp1.bin
cirrus/cs35l54-b0-dsp1-misc-
103c8d85-amp2.bin
cirrus/cs35l54-b0-dsp1-misc-
103c8d85-amp3.bin
cirrus/cs35l54-b0-dsp1-misc-
103c8d85-amp4.bin
cirrus/cs35l54-b0-dsp1-misc-
103c8d86-amp1.bin
cirrus/cs35l54-b0-dsp1-misc-
103c8d86-amp2.bin
cirrus/cs35l54-b0-dsp1-misc-
103c8d86-amp3.bin
cirrus/cs35l54-b0-dsp1-misc-
103c8d86-amp4.bin
cirrus/cs35l54-b0-dsp1-misc-
103c8d8c-amp1.bin
cirrus/cs35l54-b0-dsp1-misc-
103c8d8c-amp2.bin
cirrus/cs35l54-b0-dsp1-misc-
103c8d8d-amp1.bin
cirrus/cs35l54-b0-dsp1-misc-
103c8d8d-amp2.bin
cirrus/cs35l54-b0-dsp1-misc-
103c8d8e-amp1.bin
cirrus/cs35l54-b0-dsp1-misc-
103c8d8e-amp2.bin
cirrus/cs35l54-b0-dsp1-misc-
103c8e14-amp1.bin
cirrus/cs35l54-b0-dsp1-misc-
103c8e14-amp2.bin
cirrus/cs35l54-b0-dsp1-misc-
103c8e15-amp1.bin
cirrus/cs35l54-b0-dsp1-misc-
103c8e15-amp2.bin
cirrus/cs35l54-b0-dsp1-misc-
103c8e1b-amp1.bin
cirrus/cs35l54-b0-dsp1-misc-
103c8e1b-amp2.bin
cirrus/cs35l56-b0-dsp1-misc-
103c8d90-amp1.bin
cirrus/cs35l56-b0-dsp1-misc-
103c8d90-amp2.bin
cirrus/cs35l56-b0-dsp1-misc-
10431e13-amp1.bin
cirrus/cs35l56-b0-dsp1-misc-
10431e13-amp2.bin
cirrus/cs35l56-b0-dsp1-misc-
10431e13-amp3.bin
cirrus/cs35l56-b0-dsp1-misc-
10431e13-amp4.bin
cirrus/cs35l56-b0-dsp1-misc-
10431f43-amp1.bin
cirrus/cs35l56-b0-dsp1-misc-
10431f43-amp2.bin
cirrus/cs35l56-b0-dsp1-misc-
10431f43-amp3.bin
cirrus/cs35l56-b0-dsp1-misc-
10431f43-amp4.bin
cirrus/cs35l56-b0-dsp1-misc-
17aa380e-spkid0-ampl.bin
cirrus/cs35l56-b0-dsp1-misc-
17aa380e-spkid0-ampr.bin
cirrus/cs35l56-b0-dsp1-misc-
17aa380e-spkid1-ampl.bin
cirrus/cs35l56-b0-dsp1-misc-
17aa380e-spkid1-ampr.bin
cirrus/cs35l56/CS35L56_Rev3.11.11.1.wmfw
cirrus/cs35l56/CS35L56_Rev3.11.20.wmfw
iwlwifi-bz-b0-fm-c0-94.ucode
iwlwifi-gl-c0-fm-c0-94.ucode
mediatek/BT_RAM_CODE_MT7961_1a_2_hdr.bin
mediatek/mt7988/mt7988_wo_0.bin
mediatek/mt7988/mt7988_wo_1.bin
mediatek/mt7996/mt7992_dsp_23.bin
mediatek/mt7996/mt7992_dsp.bin
mediatek/mt7996/mt7992_eeprom_23_2i5i.bin
mediatek/mt7996/mt7992_eeprom_23.bin
mediatek/mt7996/mt7992_eeprom_2i5e.bin
mediatek/mt7996/mt7992_eeprom_2i5i.bin
mediatek/mt7996/mt7992_eeprom.bin
mediatek/mt7996/mt7992_rom_patch_23.bin
mediatek/mt7996/mt7992_rom_patch.bin
mediatek/mt7996/mt7992_wa_23.bin
mediatek/mt7996/mt7992_wa.bin
mediatek/mt7996/mt7992_wm_23.bin
mediatek/mt7996/mt7992_wm.bin
mediatek/mt7996/mt7996_eeprom_233_2i5i6i.bin
mediatek/mt7996/mt7996_eeprom_233.bin
mediatek/mt7996/mt7996_eeprom_2i5i6i.bin
mediatek/mt7996/mt7996_rom_patch_233.bin
mediatek/mt7996/mt7996_wa_233.bin
mediatek/mt7996/mt7996_wm_233.bin
mediatek/WIFI_MT7961_patch_mcu_1a_2_hdr.bin
mediatek/WIFI_RAM_CODE_MT7961_1a.bin
qca/hmtbtfw20.tlv
qca/hmtnv20.b10f
qca/hmtnv20.b112
qca/hmtnv20.bin
qcom/a663_gmu.bin
qcom/qcm6490/a660_zap.mbn
qcom/qcm6490/adsp.mbn
qcom/qcm6490/adspr.jsn
qcom/qcm6490/adsps.jsn
qcom/qcm6490/adspua.jsn
qcom/qcm6490/battmgr.jsn
qcom/qcm6490/cdsp.mbn
qcom/qcm6490/cdspr.jsn
qcom/qcm6490/ipa_fws.mbn
qcom/sa8775p/a663_zap.mbn
realtek/rt1320/rt1320-patch-code-vab.bin
realtek/rt1320/rt1320-patch-code-vc.bin
rtl_nic/rtl8125d-1.fw
rtlwifi/rtl8192dufw.bin
rtw89/rtw8922a_fw-2.bin
ti/tas2781/TAS2XXX1EB30.bin
ti/tas2781/TAS2XXX1EB31.bin
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16721
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rosen Penev [Mon, 15 Jul 2024 05:59:08 +0000 (22:59 -0700)]
ath79: apply qca,tx-gain-buffalo
It seems this was only used by one device in ar71xx. Might as well
reapply it.
Make use of the separate TX gain table for WZR-HP-G450H:
https://github.com/torvalds/linux/commit/
0f978bfaf2600040f9826f394eb12e023bef3068
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15949
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Samuele Longhi [Sat, 12 Oct 2024 16:20:49 +0000 (18:20 +0200)]
ramips: mt7621: add support for Gemtek WVRTM-127ACN and WVRTM-130ACN
The Gemtek WVRTM-127ACN is an indoor dual band wifi router
with internal antennas and 3 Gigabit Ethernet ports.
The Gemtek WVRTM-130ACN is an indoor dual band wifi router
with external antennas and 5 Gigabit Ethernet ports.
Hardware of WVRTM-127ACN:
- SoC: Mediatek MT7621AT (880 MHz, dual core)
- RAM: 128 MB
- Storage: 128 MB NAND SLC flash
- Ethernet: 3x 10/100/1000 Mbps LAN1,LAN2 & WAN
- Wireless: 2.4GHz: Mediatek MT7603EN (802.11b/g/n)
- Wireless: 5GHz: Mediatek MT7612EN (802.11n/ac)
- LEDs: 11x
- Buttons: 2x WPS, reset
- USB: 1x 3.0
- Power: 56 VDC, 0.54 A, PoE+ IN (WAN)
- PoE: 1x PoE+ 802.3af/at (WAN)
- Uart: GND RX TX VCC - J2 (GND near WAN)
- Board silkscreen: "WVRTM-127ACN_V02" "19K-513-8500R" "RoHS" "1717"
Hardware of WVRTM-130ACN:
- SoC: Mediatek MT7621AT (880 MHz, dual core)
- RAM: 128 MB (Kioxia TC58BVG0S3HTA00)
- Storage: 128 MB NAND SLC (Winbond W971GG6SB-25)
- Ethernet: 5x 10/100/1000 Mbps LAN1,LAN2,LAN3,LAN4 & WAN
- Wireless: 2.4GHz and 5GHz Mediatek MT7615DN (802.11ac/b/g/n) (DBDC)
- LEDs: 10x
- Buttons: 3x Power, WPS, reset
- USB: 1x 3.0
- Power: 56 VDC, 0.54 A, PoE+ (WAN)
- PoE: 1x PoE+ 802.3af/at (WAN)
- Uart: GND RX TX VCC - J2 (GND near WAN)
- Board silkscreen: "WVRTM-130ACN_V01" "19K-515-4500R" "RoHS" "2112"
Enable access to uboot menu (needed in wvrtm-130acn):
- The access to uboot menu is blocked by `bootdelay = 0` set in ubootenv.
With stock firmware version 01.01.02.163 and previous, you can use CVE 2020-24365
command injection https://nvd.nist.gov/vuln/detail/CVE-2020-24365
python3 exploit.py -t 192.168.1.1 -c "fw_setenv bootdelay 3; fw_saveenv"
Backup the stock firmware:
- Connect via uart
- Connect via ethernet and assign your pc the address 192.168.15.x/24
- Power on the device; and start typing '4' to enter uboot menu
- Set factory mode and boot
MT7621 # setenv factory 2; saveenv
MT7621 # nand read
2800000 2000000 81000000; bootm
- Telnet and copy all mtd blocks
telnet 192.168.15.1
- Copy all mtd blocks and start webserver
for N in $(seq 0 6); do dd if=/dev/mtd$N of=/tmp/eeprom_mtd$N.bin; done
mount -o bind /tmp /www
lighttpd -f /etc/lighttpd.conf
- Backup stock rootfs_data (optional)
dd if=/dev/mtd7 of=/tmp/eeprom_mtd7.bin
dd if=/dev/mtd8 of=/tmp/eeprom_mtd8.bin
- Download to your pc from http://192.168.15.1/eeprom_mtd$N.bin
Installation:
- Connect via uart
- Connect via ethernet and assign your pc the address 10.10.10.3/24
- Start a tftp server and serve the image initramfs-kernel.bin
mkdir /tmp/ftpd;
cp initramfs-kernel.bin /tmp/ftpd/kernel.bin
dnsmasq --enable-tftp --tftp-root=/tmp/ftpd
- Power on the device; and start typing '4' to halt the bootloader
- Change the active mtd partition from mtd6 to mtd5 (needed by uboot)
MT7621 # setenv mtddevnum 5; saveenv
- Write the openwrt initramfs in ram via tftp and boot it
MT7621 # tftpboot
81000000 kernel.bin; bootm
- From the initramfs create the ubi device and install openwrt via sysupgrade
ubiformat /dev/mtd11 -y
sysupgrade -n -v /tmp/sysupgrade.bin
Recovery:
Restore the stock firmware from the backup of the mtd blocks
mtd write eeprom_mtd5.bin firmware
mtd write eeprom_mtd6.bin Kernel2
mtd write eeprom_mtd7.bin Storage1
mtd write eeprom_mtd8.bin Storage2
ubiformat /dev/mtd8 -y
reboot
Links to previous works on wvrtm-127acn:
https://github.com/digiampietro/hacking-gemtek
https://forum.openwrt.org/t/add-support-for-gemtek-wvrtm-127acn-linkem-provider/168757
Signed-off-by: Samuele Longhi <agave@dracaena.it>
Link: https://github.com/openwrt/openwrt/pull/16685
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
John Audia [Thu, 17 Oct 2024 23:46:24 +0000 (19:46 -0400)]
kernel: bump 6.6 to 6.6.57
1. Update target/linux/generic/config-6.6 for new ksym
2. Refresh patches
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.57
Added:
generic/backport-6.6/777-netfilter-xtables-fix-typo-causing-some-targets-to-not-load-on-IPv6.patch[1]
Manually rebased:
generic/hack-6.6/645-netfilter-connmark-introduce-set-dscpmark.patch
Removed upstreamed:
gemini/patches-6.6/0001-net-ethernet-cortina-Drop-TSO-support.patch[2]
gemini/patches-6.6/0004-net-ethernet-cortina-Restore-TSO-support.patch[3]
All other patches automatically rebased.
1. https://lore.kernel.org/all/
20241019-xtables-typos-v2-1-
6b8b1735dc8e@0upti.me/
2 https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.57&id=
452c0740d72c6a77a41f6ddc318a48f18c3d2346
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.57&id=
611f74b0e7fb93ee2366d9d7edca546806b220e9
Build system: x86/64
Build-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Run-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/16726
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hannu Nyman [Thu, 17 Oct 2024 17:33:36 +0000 (20:33 +0300)]
base-files: increase default system log size to 128 kB
Increase the default system log buffer size option
in /etc/config/system from 64 kB to 128 kB.
64 kB is barely enough for the boot items of a modern router
with a few add-on packages, but any subsequent logging will
quickly cause the early boot items to get overwritten in the
round-robin log buffer. Double the buffer size to 128 kB.
(Note: built-in default in ubox logd itself is still 16 kB)
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/16723
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Roger Pueyo Centelles [Fri, 18 Nov 2022 00:18:09 +0000 (01:18 +0100)]
ath79: Upstream b53 DSA driver for Ubiquiti EdgeSwitch 8XP
The swconfig-based b53 driver for the BCM53128 switch stopped working
after commits
b2cfed48f6 (Revert "swconfig: fix Broadcom b53 support")
and
e4e410733f (kernel: export switch_generic_set_link() symbol). This
rendered the 8 LAN ports of the EdgeSwitch 8XP non-functional, so the
image compilation for the device was disabled (
5a1d7d8c1b).
This commit adds the kmod-dsa-b53-mdio and kmod-dsa-b53 packages
with the upstream B53 DSA driver, replacing the swconfig-based
kmod and kmod-switch-bcm53xx-mdio downstream ones that are not used by
any other device.
The 8 LAN ports of the EdgeSwitch 8XP are usable again. The 02_network
init script has been updated with the new DSA interfaces lan1 .. lan8.
Image building has been reenabled for the device, adding the usual DSA
incompatibility notice.
Tested on a Ubiquiti EdgeSwitch 8XP.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Link: https://github.com/openwrt/openwrt/pull/11680
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Daniel Golle [Fri, 18 Oct 2024 11:38:21 +0000 (12:38 +0100)]
mediatek: filogic: convert Acer Predator W6 to use NVMEM framework
Read WiFi calibration data via NVMEM framework. The MAC addresses are
stored inside a file on a filesystem and hence still have to be
extracted in userspace.
WiFI EEPROM extraction has already accidentally been partially removed
by commit
3e6de5d77a ("mediatek: use NVMEM framework on all Adtran
devices").
Fixes: 3e6de5d77a ("mediatek: use NVMEM framework on all Adtran devices")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Felix Fietkau [Fri, 18 Oct 2024 06:03:21 +0000 (08:03 +0200)]
firewall: update to Git HEAD (2024-10-18)
ffba75c9cd8f iptables: free xtables_match if found in need_protomatch
bf1d5fdf6234 iptables: fix regression with unintended free in need_protomatch
1aef9791a21e defaults.c: fix ipv6 flow offloading
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Robert Marko [Thu, 17 Oct 2024 16:37:47 +0000 (18:37 +0200)]
lantiq: refresh patches
CI says that they need to be refreshed, so do so.
Link: https://github.com/openwrt/openwrt/pull/16722
Signed-off-by: Robert Marko <robimarko@gmail.com>
Robert Marko [Thu, 17 Oct 2024 16:37:27 +0000 (18:37 +0200)]
realtek: refresh patches
CI says that they need to be refreshed, so do so.
Link: https://github.com/openwrt/openwrt/pull/16722
Signed-off-by: Robert Marko <robimarko@gmail.com>
Jack Sun [Thu, 17 Oct 2024 11:37:38 +0000 (19:37 +0800)]
package: busybox: update download link
There is no file named busybox-1.36.1.tar.bz2 in the root directory of the website
The actual download link is “https://sources.buildroot.net/busybox/busybox-1.36.1.tar.bz2”
Signed-off-by: Jack Sun <sunjiazheng321521@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16719
Signed-off-by: Robert Marko <robimarko@gmail.com>
Hannu Nyman [Wed, 16 Oct 2024 19:03:34 +0000 (22:03 +0300)]
base-files: Increase failsafe trigger wait time from 2 to 4 sec
Increase the failsafe waiting timeout period from 2 seconds
to 4 seconds.
Since commit
29207748b in 2015 we have had a rapid LED blinking
indication for the failsafe triggering period. But the really short
timeout of 2 seconds requires snappy reaction time from the user to
notice the LED blinking and to push button inside the short window.
Relax the timeout to 4 seconds, which more easily allows to notice
the change in LED blinking and push a button.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/11852
Signed-off-by: Robert Marko <robimarko@gmail.com>
Robert Marko [Thu, 17 Oct 2024 12:27:04 +0000 (14:27 +0200)]
ath11k-firmware: update IPQ8074 and QCN9074 to 2.9.0.1-02146
After a long time QCA has pushed an updated release of 2.9.0.1 firmware
for IPQ8074 and QCN9074, so lets update to 2.9.0.1-02146.
Sadly, still nothing new for IPQ6018.
QCA has also moved the repository where they will be posting firmware to
their CodeLinaro instance, so we move to using that and it allows us to
remove the manual download of QCN9074 board-2.bin.
Link: https://github.com/openwrt/openwrt/pull/16720
Signed-off-by: Robert Marko <robimarko@gmail.com>
Daniel Golle [Thu, 17 Oct 2024 12:33:18 +0000 (13:33 +0100)]
generic: import and move accepted RealTek PHY patches
Import commits from upstream Linux and move/rename existing patches
which have been acceped.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
David Bauer [Wed, 22 Nov 2023 01:45:13 +0000 (02:45 +0100)]
mpc85xx: convert Watchguard T10 mac-assignment to NVMEM
MAC-addresses are stored with colons, thus they can now be referenced
using NVMEM.
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16310
Signed-off-by: Robert Marko <robimarko@gmail.com>
Rosen Penev [Wed, 16 Oct 2024 22:31:20 +0000 (15:31 -0700)]
mpc85xx: p1010: fix NAND devices
Upstream commit
9ba0cae3cac07c21c583f9ff194f74043f90d29c made FSL_IFC
visible and selectable, which means that in order for MTD_NAND_FSL_IFC
to work, it needs these two extra CONFIG options.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16717
Signed-off-by: Robert Marko <robimarko@gmail.com>
INAGAKI Hiroshi [Sun, 13 Oct 2024 15:31:43 +0000 (00:31 +0900)]
uboot-ath79: update to U-Boot v2024.10
Update uboot-ath79 package to U-Boot v2024.10.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16703
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Chukun Pan [Thu, 10 Oct 2024 15:10:28 +0000 (23:10 +0800)]
mac80211: realtek: rtw89: add RTL8922AE support
Add the Realtek RTL8922AE support to rtw89 package.
The 8922A is a 802.11be chip that can support 2/5/6GHz 160MHz.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/16700
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Chukun Pan [Wed, 9 Oct 2024 15:10:26 +0000 (23:10 +0800)]
linux-firmware: update Realtek RTW89 firmware
Add RealTek RTL8922AE firmware package. The rtw89 driver uses
rtw8852b_fw-1.bin starting from kernel 6.4[1], remove the old
one. Also note that in the kernel 6.12, rtw8852c and rtw8922a
should use fw-1.bin [2][3].
[1] https://github.com/torvalds/linux/commit/
ffde7f3476
[2] https://github.com/torvalds/linux/commit/
45ae0e8cf8
[3] https://github.com/torvalds/linux/commit/
6ca6b918f2
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Suggested-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/16700
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Andre Heider [Mon, 9 Jan 2023 15:38:05 +0000 (16:38 +0100)]
prereq-build: limit python distutils check to <v3.12
v3.12 won't have it anymore.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16699
Signed-off-by: Robert Marko <robimarko@gmail.com>
Paul Spooren [Sat, 17 Aug 2024 14:23:54 +0000 (16:23 +0200)]
prereq-build: add Python 3.12 support
This reverts commit
09b7e1955c92e0b05197174b7bd4aef2c4073a35.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Link: https://github.com/openwrt/openwrt/pull/16699
Signed-off-by: Robert Marko <robimarko@gmail.com>
Robert Marko [Wed, 16 Oct 2024 09:14:54 +0000 (11:14 +0200)]
opkg: update to Git HEAD (2024-10-16)
38eccbb1fd69 libopkg: allow install package from https and ftps
Link: https://github.com/openwrt/openwrt/pull/16715
Signed-off-by: Robert Marko <robimarko@gmail.com>
Felix Fietkau [Wed, 16 Oct 2024 07:55:18 +0000 (09:55 +0200)]
ramips: disable CONFIG_LIST_HARDENED on MT7620
In #16396, crashes were reported on MT7620, which were introduced by enabling
CONFIG_LIST_HARDENED. The cause seems to be random memory corruption somewhere
in the kernel. Unfortunately the crash traces do not point to the real cause
of the crash in any way.
Since MT7620 is really ancient hardware that likely only has few users left,
I don't expect that anybody will invest a significant amount of time to track
down the real cause. Because of that, let's disable CONFIG_LIST_HARDENED on
this target only, and leave it enabled on all other platforms.
Fixes: #16396
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Jonas Jelonek [Tue, 15 Oct 2024 18:52:35 +0000 (20:52 +0200)]
uboot-mediatek: add noncached_set_region prototype to fix build
Building uboot-mediatek fails with GCC-14, uboot v2024.10 and
CONFIG_SYS_NONCACHED_MEMORY defined with error:
cmd/cache.c: In function 'do_dcache':
cmd/cache.c:57:25: error: implicit declaration of function
'noncached_set_region' [-Wimplicit-function-declaration]
This is caused by upstream commit
7d6cee2cd0e2e2507aca1e3a6fe0e2cb241a116e
("cmd: cache: Remove weak functions") as this removes weak functions in
favor of arch-specific definitions.
This patch adds the function prototype for `noncached_set_region` to
arch-specific header for ARM. It also adds an include in cmd/cache.c to
make the function available there.
Fixes: #16697
Fixes: f8c22c9bff ("uboot-mediatek: update to U-Boot 2024.10")
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
[@dangowrt refreshed patch]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Tue, 15 Oct 2024 23:10:28 +0000 (00:10 +0100)]
mediatek: mt7622: add netdev rename preinit script
Add preinit script to rename network interfaces according to the
label provided in Device Tree.
Fixes: b6d8297510 ("mediatek: mt7622: add Adtran SmartRG SDG-841t6 device")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Chukun Pan [Fri, 20 Sep 2024 15:10:26 +0000 (23:10 +0800)]
mediatek: filogic: reorder alphabetically
Reorder scripts to keep alphabetical order.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Chukun Pan [Thu, 19 Sep 2024 15:10:18 +0000 (23:10 +0800)]
mediatek: filogic: fix network config for mt7986b-rfb
Fix the network configuration according to the device tree.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Daniel Golle [Tue, 15 Oct 2024 20:15:19 +0000 (21:15 +0100)]
generic: fix kernel version and ordering of Aquantia backports
Two patches declared as accepted in v6.13 were already accepted for
v6.12. Fix filenames and order of patches applied.
Reported-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Fixes: 8cc049cec2 ("generic: phy: aquantia: move accepted patches to backport-6.6")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Mon, 7 Oct 2024 14:33:21 +0000 (15:33 +0100)]
mediatek: use NVMEM framework on all Adtran devices
Use NVMEM framework to assign MAC addresses and WiFi EEPROM data on
all Adtran SmartRG devices.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sat, 5 Oct 2024 17:22:20 +0000 (18:22 +0100)]
mediatek: mt7622: add Adtran SmartRG SDG-841t6 device
Specification
SoC: MediaTek MT7622A (2x Cortex-A53)
RAM: NANYA NT5CC256M16ER-EK (512 MiB)
MMC: Kioxia THGBMNG5D1LBAIT (4 GiB)
ETH0: Intel/MaxLinear GPY211 (2500M/1000M/100M/10M)
ETH1: Lantiq/Intel/MaxLinear PEF7071/GPY111 (1000M/100M/10M)
WLAN0: MediaTek MT7915E + MT7975D 2T2R 802.11bgn/ax (2.4G)
2T2R 802.11an/ac/ax (5G L)
WLAN1: MediaTek MT7915E + MT7975A 4T4R 802.11an/ac/ax (5G H)
BT: BT5 provided by MT7915E+MT7975D (missing firmware)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sat, 5 Oct 2024 20:43:48 +0000 (21:43 +0100)]
mediatek: add driver for Adtran MFGINFO NVMEM layout
This driver allows retrieving MAC addresses and other factory information
via the NVMEM framework on Adtran devices.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 4 Oct 2024 13:04:25 +0000 (14:04 +0100)]
mediatek: mt7622: enable HWMON in kernel config
Building HWMON as module prevents some other drivers from getting built
into the kernel, e.g. mxl-gpy. Always enable HWMON and also set
THERMAL_HWMON.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sat, 5 Oct 2024 21:21:17 +0000 (22:21 +0100)]
generic: net: phy: intel-way: add support for PHY LEDs
Add driver support for PHY LEDs for MaxLinear/Intel/Lantiq XWAY
Ethernet PHYs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Tue, 1 Oct 2024 23:35:07 +0000 (00:35 +0100)]
generic: net: phy: mxl-gpy: add support for PHY LEDs
Add driver support for PHY LEDs for MaxLinear/Intel GPY Ethernet PHYs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sat, 5 Oct 2024 21:19:43 +0000 (22:19 +0100)]
generic: phy: aquantia: correctly describe LED polarity
Backport newly introduced support for 'active-high' property and use
it to correctly implement polarity assignment for Aquantia PHY LEDs.
Previously the 'active-low' property was used to switch a LED PIN to
active-high ("drive VDD" in Aquantia-speak) mode.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Tue, 15 Oct 2024 16:39:13 +0000 (17:39 +0100)]
generic: phy: aquantia: move accepted patches to backport-6.6
Move patches accepted upstream from pending-6.6 to backport-6.6.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 11 Oct 2024 03:42:09 +0000 (04:42 +0100)]
generic: net: phy: be more conservative about MAC interface selection
Only add SerDes interface modes at lower speeds to host_interfaces.
Fixes: 5281033831 ("generic: net: phy: use all SerDes MAC interface modes")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Stijn Tintel [Tue, 15 Oct 2024 09:13:35 +0000 (12:13 +0300)]
qoriq: add squashfs to FEATURES
The snapshot builds for qoriq only contain ext4 images. Add squashfs to
FEATURES to also have the buildbots build squashfs images.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Felix Fietkau [Tue, 15 Oct 2024 08:21:47 +0000 (10:21 +0200)]
kernel: fix mtk_eth_soc memory corruption issue on fq dma init
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Stijn Tintel [Mon, 14 Oct 2024 21:23:36 +0000 (00:23 +0300)]
qoriq: add missing kernel config symbol
Dropping the source-only flag from qoriq and adding it to the buildbots
exposed a missing kernel config symbol: CONFIG_DRM_OFDRM. Addd it as
disabled to the qoriq kernel config, as the only device currently
supported in the qoriq target does not have any display hardware.
Reported-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Michael Pratt [Sat, 12 Oct 2024 18:55:04 +0000 (14:55 -0400)]
tools/ninja: update to 1.12.1
Update to the most recent stable release,
including a new job scheduler and bug fixes.
Backport a patch to assist in reworking jobserver support.
The original patch for jobserver support requires reworking
due to the function CanRunMore() and its usage
being significantly changed, including the return
becoming an integer instead of a boolean.
AcquireToken() must now be used in CanRunMore()
in order to quantify how much the job searching loop
is able to run at any time, and in order to do so
CanRunMore() cannot be a constant function anymore.
Added:
- 010-backport-gtest.patch
Manually Adjust:
- 100-make_jobserver_support.patch
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Link: https://github.com/openwrt/openwrt/pull/16693
Signed-off-by: Robert Marko <robimarko@gmail.com>
Michael Pratt [Fri, 2 Aug 2024 08:02:58 +0000 (04:02 -0400)]
tools/ninja: use existing ninja to build ninja
Add methods to skip the building and execution of Ninja by python
in order to allow Make to execute Ninja after the configure script.
This allows the user to build Ninja only once
if they already have an older version of Ninja built.
It also allows the user to test the jobserver functionality
by having Ninja built twice (clean then compile).
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Link: https://github.com/openwrt/openwrt/pull/16693
Signed-off-by: Robert Marko <robimarko@gmail.com>
Michael Pratt [Mon, 22 Jul 2024 19:51:12 +0000 (15:51 -0400)]
tools/ninja: cleanup Makefile
Use default CXXFLAGS and LDFLAGS variables.
Directly add --verbose flag without a variable.
Split up lines for script arguments.
Delete unnecessary lines.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Link: https://github.com/openwrt/openwrt/pull/16693
Signed-off-by: Robert Marko <robimarko@gmail.com>
Robert Marko [Mon, 14 Oct 2024 11:02:24 +0000 (13:02 +0200)]
mvebu: cortex-a9: add upgrade methode to nas1dual
The blamed commit adds a upgrade recipe for nas1dual to specify the
firmware partition name, but does not actually include the recipe that
will be called.
Since it previously relied on the default one, add that one.
Fixes: d21720fa90c8 ("mvebu: fix default partition name")
Link: https://github.com/openwrt/openwrt/pull/16704
Signed-off-by: Robert Marko <robimarko@gmail.com>
Stijn Tintel [Sun, 13 Oct 2024 13:12:58 +0000 (16:12 +0300)]
xdp-tools: bump to 1.4.3
Release notes:
https://github.com/xdp-project/xdp-tools/releases/tag/v1.4.3
Remove upstreamed patch
023-libxdp-fix-compilation-on-multiarch-systems.patch.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Stijn Tintel [Sun, 13 Oct 2024 17:21:44 +0000 (20:21 +0300)]
libbpf: bump to 1.4.6
Release notes:
https://github.com/libbpf/libbpf/releases/tag/v1.4.6
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Stijn Tintel [Sun, 13 Oct 2024 19:25:10 +0000 (22:25 +0300)]
qoriq: drop source-only flag
While the qoriq target currently supports only one device, the
WatchGuard Firebox M300, the feedback from people using it is that it's
a great bang for the buck. Additionally, people suggest having no
snapshots available hurts adoption.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Rosen Penev [Sun, 1 Sep 2024 22:33:43 +0000 (15:33 -0700)]
qoriq: use nvmem for MAC addresses
Userspace handling is deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16308
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Peter Körner [Fri, 4 Oct 2024 20:50:49 +0000 (22:50 +0200)]
rtl83xx: fix typo
Removes an unwanted special character in a debug-message.
Signed-off-by: Peter Körner <peter@mazdermind.de>
Boris Krasnovskiy [Sun, 13 Oct 2024 00:01:57 +0000 (20:01 -0400)]
mvebu: fix sysupgrade failure
Linksys devices do no pass $cmd at all.
Fixes: #16148
Fixes: 715634e6d144 ("base-files: upgrade: nand: use "cmd" argument for extracting command")
Signed-off-by: Boris Krasnovskiy <borkra@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16690
Signed-off-by: Robert Marko <robimarko@gmail.com>
Boris Krasnovskiy [Sat, 12 Oct 2024 23:57:16 +0000 (19:57 -0400)]
mvebu: fix default partition name
The firmware partition name is specifc to ipTIME NAS1dual and should not be
set globally.
Fixes: #16148
Fixes: 6ff970bb51f5 ("mvebu: add support for ipTIME NAS1dual")
Signed-off-by: Boris Krasnovskiy <borkra@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16690
Signed-off-by: Robert Marko <robimarko@gmail.com>
Felix Fietkau [Sun, 6 Oct 2024 15:43:23 +0000 (17:43 +0200)]
mac80211: fix letting drivers iterate over keys
Skip non-uploaded keys to avoid corner cases
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Jack Sun [Sat, 12 Oct 2024 15:36:17 +0000 (23:36 +0800)]
tools/cmake: update to 3.30.5
Release notes: https://cmake.org/cmake/help/latest/release/3.30.html
Signed-off-by: Jack Sun <sunjiazheng321521@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16657
Signed-off-by: Robert Marko <robimarko@gmail.com>