Huang Shijie [Fri, 17 May 2013 03:17:32 +0000 (11:17 +0800)]
mtd: parse out the ECC info for the full-id nand chips
Parse out the ECC information for the full-id nand chips.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Huang Shijie [Fri, 17 May 2013 03:17:31 +0000 (11:17 +0800)]
mtd: add ECC info for nand_flash_dev{}
Add an instance of an anonymous struct to store the ECC info for full id
nand chips.
@ecc.strength_ds: ECC correctability from the datasheet.
@ecc.step_ds: ECC size required by the @ecc.strength_ds,
These two fields are all from the datasheet.
Also add the necessary macros to make the code simple and clean.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Huang Shijie [Fri, 17 May 2013 03:17:30 +0000 (11:17 +0800)]
mtd: replace the hardcode with the onfi_feature()
The current code uses the hardcode to detect the 16-bit bus width.
Use the onfi_feature() to replace it.
Signed-off-by: Huang Shijie <b32955@freescale.com>
[Brian: small fixup]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Huang Shijie [Wed, 22 May 2013 02:28:27 +0000 (10:28 +0800)]
mtd: get the ECC info from the Extended Parameter Page
Since the ONFI 2.1, the onfi spec adds the Extended Parameter Page
to store the ECC info.
The onfi spec tells us that if the nand chip's recommended ECC codeword
size is not 512 bytes, then the @ecc_bits is 0xff. The host _SHOULD_ then
read the Extended ECC information that is part of the extended parameter
page to retrieve the ECC requirements for this device.
This patch implement the reading of the Extended Parameter Page, and parses
the sections for ECC type, and get the ECC info from the ECC section.
Tested this patch with Micron MT29F64G08CBABAWP.
Acked-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Huang Shijie <b32955@freescale.com>
Reviewed-and-tested-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Huang Shijie [Fri, 17 May 2013 03:17:28 +0000 (11:17 +0800)]
mtd: add a helper to get the supported features for ONFI nand
add a helper to get the supported features for ONFI nand.
Also add the neccessary macros.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Reviewed-and-tested-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Huang Shijie [Fri, 17 May 2013 03:17:27 +0000 (11:17 +0800)]
mtd: add data structures for Extended Parameter Page
Since the ONFI 2.1, the onfi spec adds the Extended Parameter Page
to store the ECC info.
The onfi spec tells us that if the nand chip's recommended ECC codeword
size is not 512 bytes, then the @ecc_bits is 0xff. The host _SHOULD_ then
read the Extended ECC information that is part of the extended parameter
page to retrieve the ECC requirements for this device.
This patch adds
[1] the neccessary fields for nand_onfi_params{},
[2] and adds the onfi_ext_ecc_info{} for Extended ECC information,
[3] adds onfi_ext_section{} for extended sections,
[4] and adds onfi_ext_param_page{} for the Extended Parameter Page.
Acked-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Huang Shijie <b32955@freescale.com>
Reviewed-and-tested-by: Brian Norris <computersforpeace@gmail.com>
[Brian: amended for checkpatch.pl]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Huang Shijie [Fri, 17 May 2013 03:17:26 +0000 (11:17 +0800)]
mtd: get the ECC info from the parameter page for ONFI nand
From the ONFI spec, we can just get the ECC info from the @ecc_bits field of
the parameter page.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Reviewed-and-tested-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Huang Shijie [Fri, 17 May 2013 03:17:25 +0000 (11:17 +0800)]
mtd: add datasheet's ECC information to nand_chip{}
1.) Why add the ECC information to the nand_chip{} ?
Each nand chip has its requirement for the ECC correctability, such as
"4bit ECC for each 512Byte" or "40bit ECC for each 1024Byte".
This ECC info is very important to the nand controller, such as gpmi.
Take the Micron MT29F64G08CBABA for example, its geometry is
8KiB page size, 744 bytes oob size and it requires 40bit ECC per 1KiB.
If we do not provide the ECC info to the gpmi nand driver, it has to
calculate the ECC correctability itself. The gpmi driver will gets the 56bit
ECC for per 1KiB which is beyond its BCH's 40bit ecc capibility.
The gpmi will quits in this case. But in actually, the gpmi can supports
this nand chip if it can get the right ECC info.
2.) about the new fields.
The @ecc_strength_ds stands for the ecc bits needed within the @ecc_step_ds.
The two fields should be set from the nand chip's datasheets.
For example:
"4bit ECC for each 512Byte" could be:
@ecc_strength_ds = 4, @ecc_step_ds = 512.
"40bit ECC for each 1024Byte" could be:
@ecc_strength_ds = 40, @ecc_step_ds = 1024.
3.) Why do not re-use the @strength and @size in the nand_ecc_ctrl{}?
The @strength and @size in nand_ecc_ctrl{} is used by the nand controller
driver, while the @ecc_strength_ds and @ecc_step_ds are get from the datasheet.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Reviewed-and-tested-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Josh Wu [Wed, 7 Aug 2013 09:58:11 +0000 (17:58 +0800)]
mtd: atmel_nand: move the sanity check to the beginning of pmecc_enable()
It is better to do the sanity check for the parameter before any hardware
operation.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Jingoo Han [Tue, 30 Jul 2013 08:18:53 +0000 (17:18 +0900)]
mtd: onenand: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Jingoo Han [Tue, 30 Jul 2013 08:18:33 +0000 (17:18 +0900)]
mtd: nand: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Jingoo Han [Tue, 30 Jul 2013 08:18:06 +0000 (17:18 +0900)]
mtd: maps: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Jingoo Han [Tue, 30 Jul 2013 08:17:44 +0000 (17:17 +0900)]
mtd: devices: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Akinobu Mita [Sat, 27 Jul 2013 14:09:53 +0000 (23:09 +0900)]
mtd: denali: use NAND_CI_CELLTYPE_MSK instead of hardcoded constant
Use NAND_CI_CELLTYPE_MSK to extract the cell type from nand_chip.cellinfo
instead of hardcoded constant.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Artem Bityutskiy <dedekind1@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Lothar Waßmann [Wed, 7 Aug 2013 06:15:38 +0000 (08:15 +0200)]
mtd: nand: gpmi-nand: use more sensible error codes at various places
Acked-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Josh Wu [Wed, 7 Aug 2013 03:36:09 +0000 (11:36 +0800)]
mtd: atmel_nand: fix the warning when CONFIG_OF is not defined
This patch fix following warning:
drivers/mtd/nand/atmel_nand.c:2007: warning: 'atmel_nand_nfc_match' defined but not used
This patch add '#if defined(CONFIG_OF)' block to guard around the definition
of atmel_nand_nfc_match, in order to avoid the warning when the kernel is
configured without DT support.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Akinobu Mita [Sat, 3 Aug 2013 09:52:16 +0000 (18:52 +0900)]
mtd: mtd_nandbiterrs: use mtd_test helpers
Use mtdtest_write() and mtdtest_erase_eraseblock() in mtd_test helpers.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Iwo Mergler <Iwo.Mergler@netcommwireless.com.au>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Vikram Narayanan <vikram186@gmail.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Akinobu Mita [Sat, 3 Aug 2013 09:52:15 +0000 (18:52 +0900)]
mtd: mtd_torturetest: use mtd_test helpers
Use mtdtest_scan_for_bad_eraseblocks() and mtdtest_erase_good_eraseblocks()
in mtd_test helpers.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Vikram Narayanan <vikram186@gmail.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Akinobu Mita [Sat, 3 Aug 2013 09:52:14 +0000 (18:52 +0900)]
mtd: mtd_subpagetest: use mtd_test helpers
Use mtdtest_scan_for_bad_eraseblocks() and mtdtest_erase_good_eraseblocks()
in mtd_test helpers.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Vikram Narayanan <vikram186@gmail.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Akinobu Mita [Sat, 3 Aug 2013 09:52:13 +0000 (18:52 +0900)]
mtd: mtd_stresstest: use mtd_test helpers
Use mtdtest_read(), mtdtest_write(), mtdtest_erase_eraseblock(), and
mtdtest_scan_for_bad_eraseblocks() in mtd_test helpers.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Vikram Narayanan <vikram186@gmail.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Akinobu Mita [Sat, 3 Aug 2013 09:52:12 +0000 (18:52 +0900)]
mtd: mtd_speedtest: use mtd_test helpers
Use mtdtest_write(), mtdtest_read(), mtdtest_scan_for_bad_eraseblocks(),
mtdtest_erase_good_eraseblocks() in mtd_test helpers.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Vikram Narayanan <vikram186@gmail.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Akinobu Mita [Sat, 3 Aug 2013 09:52:11 +0000 (18:52 +0900)]
mtd: mtd_readtest: use mtd_test helpers
Use mtdtest_read() and mtdtest_scan_for_bad_eraseblocks() in mtd_test
helpers.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Vikram Narayanan <vikram186@gmail.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Akinobu Mita [Sat, 3 Aug 2013 09:52:10 +0000 (18:52 +0900)]
mtd: mtd_pagetest: use mtd_test helpers
Use mtdtest_write(), mtdtest_read(), mtdtest_erase_eraseblock(),
mtdtest_scan_for_bad_eraseblocks(), and mtdtest_erase_good_eraseblocks()
in mtd_test helpers.
[dwmw2: merge later 'remove always true condition' fix]
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Vikram Narayanan <vikram186@gmail.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Akinobu Mita [Sat, 3 Aug 2013 09:52:09 +0000 (18:52 +0900)]
mtd: mtd_oobtest: use mtd_test helpers
Use mtdtest_scan_for_bad_eraseblocks(), mtdtest_erase_good_eraseblocks(),
and mtdtest_erase_eraseblock() in mtd_test helpers.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Vikram Narayanan <vikram186@gmail.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Akinobu Mita [Sat, 3 Aug 2013 09:52:08 +0000 (18:52 +0900)]
mtd: tests: rename sources in order to link a helper object
Each mtd test module have a single source whose name is the same as
the module name. In order to link a single object including helper
functions to every test module, this rename these sources to the
different names.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Vikram Narayanan <vikram186@gmail.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Akinobu Mita [Sat, 3 Aug 2013 09:52:07 +0000 (18:52 +0900)]
mtd: tests: introduce helper functions
This introduces the helper functions which can be used by several
mtd/tests modules.
The following three functions are used all over the test modules.
- mtdtest_erase_eraseblock()
- mtdtest_scan_for_bad_eraseblocks()
- mtdtest_erase_good_eraseblocks()
The following are wrapper functions for mtd_read() and mtd_write()
which can simplify the return value check.
- mtdtest_read()
- mtdtest_write()
All helpers are put into a single .c file and it will be linked to
every test module later. The code will actually be copied to every
test module, but it is fine for our small test infrastructure.
[dwmw2: merge later 'return -EIO when mtdtest_read() failed' fix]
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Vikram Narayanan <vikram186@gmail.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Brian Norris [Wed, 31 Jul 2013 00:53:00 +0000 (17:53 -0700)]
mtd: nand: remove NAND_BBT_SCANEMPTY
NAND_BBT_SCANEMPTY is a strange, badly-supported option with omap as its
single remaining user.
NAND_BBT_SCANEMPTY was likely used by accident in omap2[1]. And anyway,
omap2 doesn't scan the chip for bad blocks (courtesy of
NAND_SKIP_BBTSCAN), and so its use of this option is irrelevant.
This patch drops the NAND_BBT_SCANEMPTY option.
[1] http://lists.infradead.org/pipermail/linux-mtd/2012-July/042902.html
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Ivan Djelic <ivan.djelic@parrot.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Brian Norris [Wed, 31 Jul 2013 00:52:59 +0000 (17:52 -0700)]
mtd: nand: hide in-memory BBT implementation details
nand_base.c shouldn't have to know the implementation details of
nand_bbt's in-memory BBT. Specifically, nand_base shouldn't perform the
bit masking and shifting to isolate a BBT entry.
Instead, just move some of the BBT code into a new nand_markbad_bbt()
interface. This interface allows external users (i.e., nand_base) to
mark a single block as bad in the BBT. Then nand_bbt will take care of
modifying the in-memory BBT and updating the flash-based BBT (if
applicable).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Brian Norris [Wed, 31 Jul 2013 00:52:58 +0000 (17:52 -0700)]
mtd: nand: refactor chip->block_markbad interface
The chip->block_markbad pointer should really only be responsible for
writing a bad block marker for new bad blocks. It should not take care
of BBT-related functionality, nor should it handle bookkeeping of bad
block stats.
This patch refactors the 3 users of the block_markbad interface (plus
the default nand_base implementation) so that the common code is kept in
nand_block_markbad_lowlevel(). It removes some inconsistencies between
the various implementations and should allow for more centralized
improvements in the future.
Because gpmi-nand no longer needs the nand_update_bbt() function, let's
stop exporting it as well.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Huang Shijie <b32955@freescale.com> (for gpmi-nand parts)
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Brian Norris [Wed, 31 Jul 2013 00:52:57 +0000 (17:52 -0700)]
mtd: nand: eliminate cast
Just make 'res' an int.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Brian Norris [Wed, 31 Jul 2013 00:52:56 +0000 (17:52 -0700)]
mtd: nand: remove multiplied-by-2 block logic
The parent commit
771c568bcf915e708ae819ef9d07d862f7e2da86 ("mtd: nand: add
accessors, macros for in-memory BBT") makes the following comment obsolete:
/*
* Note that numblocks is 2 * (real numblocks) here, see i+=2
* below as it makes shifting and masking less painful
*/
I don't think it ever could have been "less painful" to have to shift an
extra bit (or 2, or 3) at various points in nand_bbt.c (and even
outside, since we leak our in-memory format). But now it is certainly
more painful, since we have nice macros and functions to retrieve the
relevant portions of the BBT.
This patch removes any points where the block number is
doubled/halved/otherwise-shifted, instead representing the block number
in its most natural form: as the actual block number.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Brian Norris [Wed, 31 Jul 2013 00:52:55 +0000 (17:52 -0700)]
mtd: nand: add accessors, macros for in-memory BBT
There is an abundance of magic numbers and complicated shifting/masking
logic in the in-memory BBT code which makes the code unnecessary complex
and hard to read.
This patch adds macros to represent the 00b, 01b, 10b, and 11b
memory-BBT magic numbers, as well as two accessor functions for reading
and marking the memory-BBT bitfield for a given block.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Josh Wu [Mon, 5 Aug 2013 11:14:38 +0000 (19:14 +0800)]
mtd: ofpart: add compatible check for child nodes
In case that the nand device will support some features like Nand Flash
Controller, we want to make the sub feature as a sub node of nand device.
Use such organization it is easy to enable/disable feature, also it is back
compatible and more readable.
If the sub-node has a compatible property then it is a driver not partition.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
[ added a missing newline -Brian ]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Josh Wu [Mon, 5 Aug 2013 11:14:37 +0000 (19:14 +0800)]
mtd: atmel_nand: enable Nand Flash Controller (NFC) write via sram
This patch enable writing nand flash via NFC SRAM. It will minimize the CPU
overhead. The SRAM write only support ECC_NONE and ECC_HW with PMECC.
To enable this NFC write by SRAM feature, you can add a string in dts under
NFC driver node.
This driver has been tested on SAMA5D3X-EK with JFFS2, YAFFS2, UBIFS and
mtd-utils.
Here is part of mtd_speedtest (writing test) result, compare with non-NFC
writing, it reduces %65 cpu load with loss %12 speed.
- commands use to test:
# insmod /mnt/mtd_speedtest.ko dev=2 &
# top -n 30 -d 1 | grep speedtest
- test result:
=================================================
mtd_speedtest: MTD device: 2
mtd_speedtest: MTD device size
41943040, eraseblock size 131072, page size 2048, count of eraseblocks 320, pages per eraseblock 64, OOB size 64
mtd_speedtest: testing eraseblock write speed
509 495 root D 1164 0% 7% insmod /mnt/mtd_speedtest.ko dev=2
509 495 root D 1164 0% 8% insmod /mnt/mtd_speedtest.ko dev=2
509 495 root R 1164 0% 5% insmod /mnt/mtd_speedtest.ko dev=2
mtd_speedtest: eraseblock write speed is 5194 KiB/s
mtd_speedtest: testing page write speed
509 495 root D 1164 0% 32% insmod /mnt/mtd_speedtest.ko dev=2
509 495 root D 1164 0% 27% insmod /mnt/mtd_speedtest.ko dev=2
509 495 root D 1164 0% 25% insmod /mnt/mtd_speedtest.ko dev=2
509 495 root D 1164 0% 30% insmod /mnt/mtd_speedtest.ko dev=2
mtd_speedtest: page write speed is 5024 KiB/s
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Josh Wu [Mon, 5 Aug 2013 11:14:36 +0000 (19:14 +0800)]
mtd: atmel_nand: enable Nand Flash Controller (NFC) read data via sram
NFC has embedded sram which can use to transfer data. This patch enable reading
nand flash via NFC SRAM. It will minimize the CPU overhead.
This driver has been tested on SAMA5D3X-EK with JFFS2, YAFFS2, UBIFS and
mtd-utils.
Here puts the part of mtd_speedtest (read test) result as following:
Compare with non-NFC mtd_speedtest result, reading will reduce %45 cpu load
with increase %80 speed.
- commands use to test:
# insmod /mnt/mtd_speedtest.ko dev=2 &
# top -n 30 -d 1 | grep speedtest
- test result:
=================================================
mtd_speedtest: MTD device: 2
mtd_speedtest: MTD device size
41943040, eraseblock size 131072, page size 2048, count of eraseblocks 320, pages per eraseblock 64, OOB size 64
mtd_speedtest: testing eraseblock read speed
509 495 root D 1164 0% 28% insmod /mnt/mtd_speedtest.ko dev=2
509 495 root D 1164 0% 25% insmod /mnt/mtd_speedtest.ko dev=2
509 495 root D 1164 0% 26% insmod /mnt/mtd_speedtest.ko dev=2
mtd_speedtest: eraseblock read speed is 9403 KiB/s
mtd_speedtest: testing page read speed
509 495 root R 1164 0% 31% insmod /mnt/mtd_speedtest.ko dev=2
509 495 root D 1164 0% 57% insmod /mnt/mtd_speedtest.ko dev=2
509 495 root D 1164 0% 53% insmod /mnt/mtd_speedtest.ko dev=2
509 495 root D 1164 0% 71% insmod /mnt/mtd_speedtest.ko dev=2
mtd_speedtest: page read speed is 9258 KiB/s
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Josh Wu [Mon, 5 Aug 2013 11:14:35 +0000 (19:14 +0800)]
mtd: atmel_nand: add Nand Flash Controller (NFC) support
Nand Flash Controller (NFC) can handle automatic transfers, sending the
commands and address cycles to the NAND Flash.
To use NFC in this driver, user needs to add NFC child node in nand flash
driver. The NFC child node includes NFC's compatible string and regiters
of the address and size of NFC command registers, NFC registers (embedded
in HSMC) and NFC SRAM.
Also user need to set up the HSMC irq, which use to check whether nfc
command is finish or not.
This driver has been tested on SAMA5D3X-EK board with JFFS2, YAFFS,
UBIFS and mtd-utils.
I put the part of the mtd_speedtest result here for your information.
>From the mtd_speedtest, we can see the NFC will reduce the %50 of cpu load
when writing nand flash. No change when reading.
In the meantime, the speed will be slow about %8.
- commands use to test:
#insmod /mnt/mtd_speedtest.ko dev=2 &
#top -n 30 -d 1 | grep speedtest
- test result:
Before the patch:
=================================================
mtd_speedtest: MTD device: 2
mtd_speedtest: MTD device size
41943040, eraseblock size 131072, page size 2048, count of eraseblocks 320, pages per eraseblock 64, OOB size 64
515 495 root R 1164 0% 93% insmod /mnt/mtd_speedtest.ko dev=2
515 495 root R 1164 0% 98% insmod /mnt/mtd_speedtest.ko dev=2
515 495 root R 1164 0% 99% insmod /mnt/mtd_speedtest.ko dev=2
mtd_speedtest: eraseblock write speed is 5768 KiB/s
mtd_speedtest: testing eraseblock read speed
515 495 root R 1164 0% 92% insmod /mnt/mtd_speedtest.ko dev=2
515 495 root R 1164 0% 91% insmod /mnt/mtd_speedtest.ko dev=2
515 495 root R 1164 0% 94% insmod /mnt/mtd_speedtest.ko dev=2
mtd_speedtest: eraseblock read speed is 5932 KiB/s
mtd_speedtest: testing page write speed
515 495 root R 1164 0% 94% insmod /mnt/mtd_speedtest.ko dev=2
515 495 root R 1164 0% 98% insmod /mnt/mtd_speedtest.ko dev=2
515 495 root R 1164 0% 98% insmod /mnt/mtd_speedtest.ko dev=2
mtd_speedtest: page write speed is 5770 KiB/s
mtd_speedtest: testing page read speed
515 495 root R 1164 0% 91% insmod /mnt/mtd_speedtest.ko dev=2
515 495 root R 1164 0% 89% insmod /mnt/mtd_speedtest.ko dev=2
515 495 root R 1164 0% 91% insmod /mnt/mtd_speedtest.ko dev=2
mtd_speedtest: page read speed is 5910 KiB/s
After the patch:
=================================================
mtd_speedtest: MTD device: 2
mtd_speedtest: MTD device size
41943040, eraseblock size 131072, page size 2048, count of eraseblocks 320, pages per eraseblock 64, OOB size 64
mtd_speedtest: testing eraseblock write speed
509 495 root D 1164 0% 49% insmod /mnt/mtd_speedtest.ko dev=2
509 495 root D 1164 0% 50% insmod /mnt/mtd_speedtest.ko dev=2
509 495 root D 1164 0% 47% insmod /mnt/mtd_speedtest.ko dev=2
mtd_speedtest: eraseblock write speed is 5370 KiB/s
mtd_speedtest: testing eraseblock read speed
509 495 root R 1164 0% 92% insmod /mnt/mtd_speedtest.ko dev=2
509 495 root R 1164 0% 91% insmod /mnt/mtd_speedtest.ko dev=2
509 495 root R 1164 0% 95% insmod /mnt/mtd_speedtest.ko dev=2
mtd_speedtest: eraseblock read speed is 5715 KiB/s
mtd_speedtest: testing page write speed
509 495 root D 1164 0% 48% insmod /mnt/mtd_speedtest.ko dev=2
509 495 root D 1164 0% 47% insmod /mnt/mtd_speedtest.ko dev=2
509 495 root D 1164 0% 50% insmod /mnt/mtd_speedtest.ko dev=2
mtd_speedtest: page write speed is 5224 KiB/s
mtd_speedtest: testing page read speed
509 495 root R 1164 0% 89% insmod /mnt/mtd_speedtest.ko dev=2
509 495 root R 1164 0% 94% insmod /mnt/mtd_speedtest.ko dev=2
509 495 root R 1164 0% 93% insmod /mnt/mtd_speedtest.ko dev=2
mtd_speedtest: page read speed is 5641 KiB/s
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Josh Wu [Mon, 5 Aug 2013 11:14:34 +0000 (19:14 +0800)]
mtd: atmel_nand: replace pmecc enable code with one function.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Jean-Christophe PLAGNIOL-VILLARD [Mon, 5 Aug 2013 11:14:33 +0000 (19:14 +0800)]
mtd: atmel_nand: use devm_xxx gpio kzalloc, gpio and ioremap
this will allow to simply the error and remove path
Cc: linux-mtd@lists.infradead.org
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
[josh.wu@atmel.com: fix checkpatch warnings and rebase to latest mtd git tree]
[josh.wu@atmel.com: replace devm_request_and_ioremap with devm_ioremap_resource]
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Akinobu Mita [Sun, 28 Jul 2013 02:21:58 +0000 (11:21 +0900)]
mtd: nandsim: remove unused ns->geom.oobshift
ns->geom.oobshift holds bits number in OOB size, but OOB size is not
always power of two. So it is useless and it actually isn't used in
this driver except for just printing the value at module loading.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Akinobu Mita [Sun, 28 Jul 2013 02:21:57 +0000 (11:21 +0900)]
mtd: nandsim: remove unused code
Remove the leftover from commit
831d316b8b80b68dcdd2b3f5ede6d33c2bbf5835
("mtd: nandsim: remove autoincrement code").
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Akinobu Mita [Sun, 28 Jul 2013 02:21:56 +0000 (11:21 +0900)]
mtd: nandsim: use NS_RAW_OFFSET()
Use NS_RAW_OFFSET() to calculate the page offset in flash RAM image by
(row, column) address.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Akinobu Mita [Sun, 28 Jul 2013 02:21:55 +0000 (11:21 +0900)]
mtd: nandsim: simplify NS_RAW_OFFSET()
Simplify the definision of NS_RAW_OFFSET() by using (ns)->geom.pgszoob
which holds the sum of page size and OOB size.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Akinobu Mita [Sun, 28 Jul 2013 02:21:54 +0000 (11:21 +0900)]
mtd: nandsim: use kasprintf()
Use kasprintf() which combines kmalloc and sprintf.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Akinobu Mita [Sun, 28 Jul 2013 02:21:53 +0000 (11:21 +0900)]
mtd: nandsim: convert pages_written[] to bitmap
nandsim.pages_written[] is the array of unsigned char which is indexed
by the page number and used for identifying which pages have been written
when cache_file is used. Each entry holds 0 (not written) or 1 (written),
so it can be converted to bitmap. This reduces the allocation size of
pages_written[] by 1/8.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Brian Norris [Tue, 25 Jun 2013 20:17:59 +0000 (13:17 -0700)]
mtd: nand: detect OOB size for Toshiba 24nm raw SLC
Toshiba NAND datasheets have not been very forthcoming on OOB size
information; they do not provide any bitfields in the ID string for
spare area. In their 24nm technology flash, however, Toshiba migrated
their NAND to have 32 bytes spare per 512 bytes of page area (up from
the traditional 16 bytes), as they now require 8-bit ECC or higher.
I have discussed this issue directly with Toshiba representatives, and
they acknowledge this problem. They recommend detecting these flash
based on their technology node as follows:
For 24nm Toshiba SLC raw NAND (not BENAND -- Built-in Ecc NAND), there
are 32 bytes of spare area for every 512 bytes of in-band data area.
We can implement this rule with the following snippet of a device ID
decode table, which applies to all their 43nm, 32nm, and 24nm SLC NAND
(this table is not fully in the NAND datasheets, but it was provided
directly by Toshiba representatives):
- ID byte 5, bit[7]:
1 -> BENAND
0 -> raw SLC
- ID byte 6, bits[2:0]:
100b -> 43nm
101b -> 32nm
110b -> 24nm
111b -> Reserved
I'm also working with Toshiba on including this bitfield description for
their 5th and 6th ID bytes in their public data sheets.
I will provide the 8-byte ID strings from the two 24nm Toshiba samples I
have; their first 6 bytes match the documentation I received from
Toshiba:
24nm SLC 1Gbit TC58NVG0S3HTA00
0x98 0xf1 0x80 0x15 0x72 0x16 0x08 0x00
24nm SLC 2Gbit TC58NVG1S3HTA00
0x98 0xda 0x90 0x15 0x76 0x16 0x08 0x00
I have also tested for regressions with:
43nm SLC 4Gbit TC58NVG2S3ETA00
0x98 0xdc 0x90 0x15 0x76 0x14 0x03 0x10
32nm SLC 8Gbit TC58NVG3SOFA00
0x98 0xd3 0x90 0x26 0x76 0x15 0x02 0x08
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Andrea Adami [Sat, 20 Jul 2013 23:07:33 +0000 (01:07 +0200)]
mtd: jedec_probe: fix LH28F640BF definition
Zaurus 5500 contains 2 LH28F640BFHE-PTTL90 (64M 4Mx16) and
the LH28F640BFHE-PTTL90.pdf datasheet available on the net shows
the exact erasesize and the OTP support.
At the moment only jedec_probe can discover the chip and
the NOR is mounted read only probably because of wrong vpp.
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Josh Wu [Wed, 3 Jul 2013 09:56:19 +0000 (17:56 +0800)]
mtd: atmel_nand: fix pmecc selction for ecc requirement typo
Atmel PMECC support 2, 4, 8, 12, 24 bit error correction.
So if the ecc requirement in ONFI is <= 2, 4, 8, 12, 24.
We will use 2, 4, 8, 12, 24.
This patch fix the typo. Use '<=' replace '<'.
Reported-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Brian Norris [Thu, 18 Jul 2013 08:17:02 +0000 (01:17 -0700)]
mtd: nand: fix NAND_BUSWIDTH_AUTO for x16 devices
The code for NAND_BUSWIDTH_AUTO is broken. According to Alexander:
"I have a problem with attach NAND UBI in 16 bit mode.
NAND works fine if I specify NAND_BUSWIDTH_16 option, but not
working with NAND_BUSWIDTH_AUTO option. In second case NAND
chip is identifyed with ONFI."
See his report for the rest of the details:
http://lists.infradead.org/pipermail/linux-mtd/2013-July/047515.html
Anyway, the problem is that nand_set_defaults() is called twice, we
intend it to reset the chip functions to their x16 buswidth verions
if the buswidth changed from x8 to x16; however, nand_set_defaults()
does exactly nothing if called a second time.
Fix this by hacking nand_set_defaults() to reset the buswidth-dependent
functions if they were set to the x8 version the first time. Note that
this does not do anything to reset from x16 to x8, but that's not the
supported use case for NAND_BUSWIDTH_AUTO anyway.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reported-by: Alexander Shiyan <shc_work@mail.ru>
Tested-by: Alexander Shiyan <shc_work@mail.ru>
Cc: Matthieu Castet <matthieu.castet@parrot.com>
Cc: <stable@vger.kernel.org> # v3.8+
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Michael Opdenacker [Mon, 8 Jul 2013 04:39:20 +0000 (06:39 +0200)]
mtd: diskonchip: remove unused entries in Kconfig
This patch proposes to remove kernel configuration parameters
defined in drivers/mtd/devices/Kconfig, but used nowhere
in the makefiles and source code (except in comments).
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Kees Cook [Mon, 8 Jul 2013 13:05:12 +0000 (06:05 -0700)]
mtd: refactor call to request_module
This reduces the size of the stack frame when calling request_module().
Performing the sprintf before the call is not needed.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Wolfram Sang [Wed, 10 Jul 2013 15:57:40 +0000 (16:57 +0100)]
mtd: atmel_nand: don't use devm_pinctrl_get_select_default() in probe
Since commit
ab78029 (drivers/pinctrl: grab default handles from device core),
we can rely on device core for setting the default pins. Compile tested only.
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Wolfram Sang [Wed, 10 Jul 2013 15:57:41 +0000 (16:57 +0100)]
mtd: gpmi-nand: don't use devm_pinctrl_get_select_default() in probe
Since commit
ab78029 (drivers/pinctrl: grab default handles from device core),
we can rely on device core for setting the default pins. Compile tested only.
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fabio Estevam [Sun, 21 Jul 2013 17:52:02 +0000 (14:52 -0300)]
mtd: nand: mxc_nand: Remove unneeded check for platform_get_resource()
devm_ioremap_resource() checks its arguments, so there is no need for
explicitly checking the return value from platform_get_resource().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Paul Bolle [Mon, 13 May 2013 14:40:39 +0000 (16:40 +0200)]
mtd: remove obsolete JEDEC mapping drivers
JEDEC device support was removed in v2.6.22. (It had been marked as
BROKEN (indirectly) since at least v2.6.12.)
When it was removed the two JEDEC mapping drivers that depended on it
should have been removed too. Do so now.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Richard Genoud [Tue, 30 Jul 2013 15:17:29 +0000 (17:17 +0200)]
mtd: atmel_nand: using a stronger ECC is not dangerous
We don't have to issue a warning when a stronger error correcting
capability is chosen.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
avinash philip [Mon, 17 Jun 2013 18:46:39 +0000 (00:16 +0530)]
mtd: devices: elm: Low power transition support
ELM is used for locating bit-flip errors in when using BCH ECC scheme.
This patch adds suspend/resume support for leaf level ELM driver,
And also provides ELM register context save & restore support, so that
configurations are preserved across hardware power-off/on transitions.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Jingoo Han [Tue, 7 May 2013 06:32:03 +0000 (15:32 +0900)]
mtd: maps: rbtx4939-flash: remove unnecessary platform_set_drvdata()
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit
0998d0631001288a5974afc0b2a5f568bcdecb4d
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Jingoo Han [Tue, 7 May 2013 06:31:29 +0000 (15:31 +0900)]
mtd: maps: ixp4xx: remove unnecessary platform_set_drvdata()
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit
0998d0631001288a5974afc0b2a5f568bcdecb4d
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Marc Kleine-Budde <mkl@blackshift.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Jingoo Han [Tue, 7 May 2013 06:30:44 +0000 (15:30 +0900)]
mtd: maps: physmap: remove unnecessary platform_set_drvdata()
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit
0998d0631001288a5974afc0b2a5f568bcdecb4d
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Jingoo Han [Tue, 7 May 2013 06:30:15 +0000 (15:30 +0900)]
mtd: maps: pxa2xx-flash: remove unnecessary platform_set_drvdata()
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit
0998d0631001288a5974afc0b2a5f568bcdecb4d
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Jingoo Han [Tue, 7 May 2013 06:21:51 +0000 (15:21 +0900)]
mtd: maps: latch-addr-flash: remove unnecessary platform_set_drvdata()
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit
0998d0631001288a5974afc0b2a5f568bcdecb4d
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Jingoo Han [Tue, 7 May 2013 06:20:58 +0000 (15:20 +0900)]
mtd: maps: sa1100-flash: remove unnecessary platform_set_drvdata()
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit
0998d0631001288a5974afc0b2a5f568bcdecb4d
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Jingoo Han [Tue, 7 May 2013 06:19:51 +0000 (15:19 +0900)]
mtd: maps: plat-ram: remove unnecessary platform_set_drvdata()
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit
0998d0631001288a5974afc0b2a5f568bcdecb4d
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Jingoo Han [Tue, 7 May 2013 06:18:51 +0000 (15:18 +0900)]
mtd: devices: elm: remove unnecessary platform_set_drvdata()
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit
0998d0631001288a5974afc0b2a5f568bcdecb4d
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Jingoo Han [Tue, 7 May 2013 06:46:11 +0000 (15:46 +0900)]
mtd: nand: txx9ndfmc: remove unnecessary platform_set_drvdata()
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit
0998d0631001288a5974afc0b2a5f568bcdecb4d
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Jingoo Han [Tue, 7 May 2013 06:45:32 +0000 (15:45 +0900)]
mtd: nand: sharpsl: remove unnecessary platform_set_drvdata()
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit
0998d0631001288a5974afc0b2a5f568bcdecb4d
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Jingoo Han [Tue, 7 May 2013 06:44:53 +0000 (15:44 +0900)]
mtd: nand: s3c2410: remove unnecessary platform_set_drvdata()
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit
0998d0631001288a5974afc0b2a5f568bcdecb4d
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Jingoo Han [Tue, 7 May 2013 06:44:14 +0000 (15:44 +0900)]
mtd: nand: pxa3xx_nand: remove unnecessary platform_set_drvdata()
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit
0998d0631001288a5974afc0b2a5f568bcdecb4d
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Jingoo Han [Tue, 7 May 2013 06:43:34 +0000 (15:43 +0900)]
mtd: nand: plat_nand: remove unnecessary platform_set_drvdata()
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit
0998d0631001288a5974afc0b2a5f568bcdecb4d
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Jingoo Han [Tue, 7 May 2013 06:42:29 +0000 (15:42 +0900)]
mtd: nand: orion_nand: remove unnecessary platform_set_drvdata()
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit
0998d0631001288a5974afc0b2a5f568bcdecb4d
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Jingoo Han [Tue, 7 May 2013 06:41:39 +0000 (15:41 +0900)]
mtd: nand: omap2: remove unnecessary platform_set_drvdata()
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit
0998d0631001288a5974afc0b2a5f568bcdecb4d
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Jingoo Han [Tue, 7 May 2013 06:17:36 +0000 (15:17 +0900)]
mtd: devices: spear_smi: remove unnecessary platform_set_drvdata()
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit
0998d0631001288a5974afc0b2a5f568bcdecb4d
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Jingoo Han [Tue, 7 May 2013 06:40:47 +0000 (15:40 +0900)]
mtd: nand: nuc900_nand: remove unnecessary platform_set_drvdata()
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit
0998d0631001288a5974afc0b2a5f568bcdecb4d
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Jingoo Han [Tue, 7 May 2013 06:40:07 +0000 (15:40 +0900)]
mtd: nand: mxc_nand: remove unnecessary platform_set_drvdata()
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit
0998d0631001288a5974afc0b2a5f568bcdecb4d
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Jingoo Han [Tue, 7 May 2013 06:39:15 +0000 (15:39 +0900)]
mtd: nand: lpc32xx: remove unnecessary platform_set_drvdata()
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit
0998d0631001288a5974afc0b2a5f568bcdecb4d
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Tested-by: Roland Stigge <stigge@antcom.de>
Acked-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Jingoo Han [Tue, 7 May 2013 06:38:25 +0000 (15:38 +0900)]
mtd: nand: jz4740_nand: remove unnecessary platform_set_drvdata()
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit
0998d0631001288a5974afc0b2a5f568bcdecb4d
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Jingoo Han [Tue, 7 May 2013 06:37:16 +0000 (15:37 +0900)]
mtd: nand: gpmi-nand: remove unnecessary platform_set_drvdata()
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit
0998d0631001288a5974afc0b2a5f568bcdecb4d
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Jingoo Han [Tue, 7 May 2013 06:36:18 +0000 (15:36 +0900)]
mtd: nand: fsmc_nand: remove unnecessary platform_set_drvdata()
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit
0998d0631001288a5974afc0b2a5f568bcdecb4d
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Jingoo Han [Tue, 7 May 2013 06:34:48 +0000 (15:34 +0900)]
mtd: nand: docg4: remove unnecessary platform_set_drvdata()
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit
0998d0631001288a5974afc0b2a5f568bcdecb4d
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Jingoo Han [Tue, 7 May 2013 06:34:07 +0000 (15:34 +0900)]
mtd: nand: bf5xx_nand: remove unnecessary platform_set_drvdata()
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit
0998d0631001288a5974afc0b2a5f568bcdecb4d
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Jingoo Han [Tue, 7 May 2013 06:33:27 +0000 (15:33 +0900)]
mtd: nand: atmel_nand: remove unnecessary platform_set_drvdata()
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit
0998d0631001288a5974afc0b2a5f568bcdecb4d
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Jingoo Han [Tue, 7 May 2013 06:32:47 +0000 (15:32 +0900)]
mtd: nand: ams-delta: remove unnecessary platform_set_drvdata()
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit
0998d0631001288a5974afc0b2a5f568bcdecb4d
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Ezequiel Garcia [Tue, 14 May 2013 11:15:25 +0000 (08:15 -0300)]
mtd: nand: pxa3xx: Add support for Read parameter page command
This command is required to identify ONFI-compliant devices.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Ezequiel Garcia [Tue, 14 May 2013 11:15:24 +0000 (08:15 -0300)]
mtd: nand: pxa3xx: Add address support for READID command
This allows to support READID ONFI command which sends 0x20
as address together with the 0x90 READID command.
This is required to detect ONFI compliant devices.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Ezequiel Garcia [Tue, 14 May 2013 11:15:23 +0000 (08:15 -0300)]
mtd: nand: pxa3xx: Fix MODULE_DEVICE_TABLE declaration
This module's device table is incorrectly declared using
i2c_pxa_dt_ids, instead of pxa3xx_nand_dt_ids.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Ezequiel Garcia [Tue, 14 May 2013 11:15:22 +0000 (08:15 -0300)]
mtd: nand: pxa3xx: Use of_machine_is_compatible()
This patch replaces cpu_is_pxa3xx() with of_machine_is_compatible()
which allows to build this driver for other platforms than ARCH_PXA.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Ezequiel Garcia [Tue, 14 May 2013 11:15:21 +0000 (08:15 -0300)]
mtd: nand: pxa3xx: Set info->use_dma properly
Currently, the variable info->use_dma is never set and always
zero-valued which means the driver never does DMA transfers.
We fix this by simply setting info->use_dma to the module parameter,
also named 'use_dma'. Note that the module parameter has the same name,
but different semantics.
This fixes a regression introduced by the below commit
which removed the info->use_dma variable set.
commit
4eb2da8994042d68e84e31138788429a102da2ea
Author: Lei Wen <leiwen@marvell.com>
Date: Mon Feb 28 10:32:13 2011 +0800
mtd: pxa3xx_nand: unify prepare command
Before the above commit, the driver had use_dma=1 on all NAND commands
except on CMD_STATUS. This behavior is long lost and we are not
recovering in this patch, either.
This was spotted and verified by human inspection.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Josh Wu [Thu, 9 May 2013 07:34:55 +0000 (15:34 +0800)]
mtd: atmel_nand: add a new dt binding item for nand dma support
This patch will set the nand dma support in dts. Since we will not use
cpu_is_xxx() in nand driver. We needn't include the mach/cpu.h any more.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Josh Wu [Thu, 9 May 2013 07:34:54 +0000 (15:34 +0800)]
mtd: atmel_nand: replace cpu_is_at32ap7000() with a nand platform data
The nand driver use cpu_is_at32ap7000() macro for a workaround. For the
multi-platform support, we will remove this cpu_is_xxx() macro.
This patch adds a boolean variable need_reset_workaround in structure
atmel_nand_data. Using this variable we can remove cpu_is_at32ap7000() macro.
Hans-Christian: Feel free to push this through the mtd tree, if they won't
accept it I'm working on getting my workflow up on the linux-avr32.git tree.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Michał Mirosław [Sat, 4 May 2013 13:19:35 +0000 (15:19 +0200)]
mtd: gpmi-nand: fix error return from gpmi_get_clks()
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Sachin Kamat [Fri, 3 May 2013 11:37:43 +0000 (17:07 +0530)]
mtd: onenand/samsung: Remove redundant platform_set_drvdata()
Commit
0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Sachin Kamat [Fri, 3 May 2013 11:37:42 +0000 (17:07 +0530)]
mtd: onenand/omap2: Remove redundant platform_set_drvdata()
Commit
0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Sachin Kamat [Fri, 3 May 2013 11:37:41 +0000 (17:07 +0530)]
mtd: onenand/generic: Remove redundant platform_set_drvdata()
Commit
0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Brian Norris [Thu, 2 May 2013 21:18:51 +0000 (14:18 -0700)]
mtd: tests: don't print error messages when out-of-memory
These strings are now unnecessary and discouraged in the kernel. The
kernel will have plenty of big scary messages if kmalloc fails. These
now only serve to bloat the module.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Laurent Navet [Thu, 2 May 2013 13:56:10 +0000 (15:56 +0200)]
mtd: nand: davinci: use devm_ioremap_resource()
Replace a call to deprecated devm_request_and_ioremap by devm_ioremap_resource.
Found with coccicheck and this semantic patch:
scripts/coccinelle/api/devm_request_and_ioremap.cocci.
Signed-off-by: Laurent Navet <laurent.navet@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
David Mosberger [Wed, 29 May 2013 12:30:13 +0000 (15:30 +0300)]
mtd: nand_base: Only use GET/SET FEATURES command on chips that support them.
Spansion's S34MLx chips support ONFI but not the GET/SET FEATURES calls.
Signed-off-by: David Mosberger <dmosberger@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Mian Yousaf Kaukab [Mon, 29 Apr 2013 12:07:48 +0000 (14:07 +0200)]
mtd: nand: fsmc: update of OF support
Add nand bank selection and timings to the device tree bindings.
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
[Added some documentation]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Huang Shijie [Wed, 15 May 2013 08:40:25 +0000 (16:40 +0800)]
mtd: increase max OOB size to 744
The oob size of Micron's MT29F64G08CBABAWP is 744 bytes.
So increase the NAND_MAX_OOBSIZE to 744.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Ezequiel Garcia [Wed, 17 Apr 2013 16:38:14 +0000 (13:38 -0300)]
mtd: nand: pxa3xx: Move buffer release code to its own function
Create a function to release the buffer and the dma channel, thus undoing
what pxa3xx_nand_init_buff() did. This commit makes the code more readable
and will allow to handle non-DMA capable platforms easier.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Ezequiel Garcia [Wed, 17 Apr 2013 16:38:13 +0000 (13:38 -0300)]
mtd: nand: pxa3xx: Check for clk_prepare_enable() return value
clk_prepare_enable() can fail due to unknown reason.
Add a check for this and return the error code if it fails.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
projects / openwrt / staging / blogic.git / log