ipmr: __pim_rcv() is called under rcu_read_lock

No need to get a reference on reg_dev and release it, we are in a
rcu_read_lock() protected section.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

gre: protocol table can be static

This table is only used in gre.c

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

enic: Update MAINTAINERS

Update MAINTAINERS list

Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David Wang <dwang2@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

enic: Make local functions static

Make functions used locally in a file as static

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David Wang <dwang2@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

enic: Remove dead code

Removed code that is unused

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David Wang <dwang2@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

neigh: reorder fields in struct neighbour

On 64bit arches, there are two 32bit holes that we can remove.

sizeof(struct neighbour) shrinks from 0xf8 to 0xf0 bytes

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

isdn/gigaset: improve bas_gigaset USB error reporting

Rephrase some USB error messages to make them clearer and more consistent.
Downgrade some warning messages that may occur during normal operation to
debug messages.

Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

isdn/gigaset: fix bas_gigaset interrupt read error handling

Rework the handling of USB errors in interrupt input reads
to clear halts correctly, delay URB resubmission after errors,
limit retries, and improve error recovery.

Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

isdn/gigaset: unclog bas_gigaset AT response pipe

Recover from a lost HD_RECEIVEATDATA_ACK message by sending a
zero-length HD_READ_ATMESSAGE command when ev_layer sends "+++".

Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

isdn/gigaset: try USB reset for bas_gigaset error recovery

In error_reset(), if sending HD_RESET_INTERRUPT_PIPE to the device
fails, try performing an USB reset.
Also correct an error in the leading comment.

Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

isdn/gigaset: bas_gigaset timer cleanup

Use setup_timer() and mod_timer() instead of direct assignment to
timer structure members, simplify the argument of one timer routine,
and make extra sure all timers are stopped during suspend.

Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

isdn/gigaset: drop obsolete debug option

Remove the debug flag DEBUG_DRIVER and associated code.
It doesn't serve any useful purpose anymore.

Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

isdn/gigaset: correct bas_gigaset rx buffer handling

In transparent data reception, avoid a NULL pointer dereference
in case an skbuff cannot be allocated, remove an inappropriate
call to the HDLC flush routine, and correct the accounting of
received bytes for continued buffers.

Signed-off-by: Tilman Schmidt <tilman@imap.cc>
CC: stable <stable@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

isdn/gigaset: fix bas_gigaset AT read error handling

Rework the handling of USB errors in AT response reads
to fix a possible infinite retry loop and a memory leak,
and silence a few overly verbose kernel messages.

Signed-off-by: Tilman Schmidt <tilman@imap.cc>
CC: stable <stable@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

isdn/gigaset: bas_gigaset locking fix

Unlock cs->lock before calling error_hangup() which is marked
"cs->lock must not be held".

Signed-off-by: Tilman Schmidt <tilman@imap.cc>
CC: stable <stable@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3: Update version to 3.114

This patch updates the tg3 version to 3.114.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3: Add extend rx ring sizes for 5717 and 5719

This patch increases the rx ring sizes for those asic revs that support
them.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3: Prepare for larger rx ring sizes

This patch adds two new variables to track the size of the standard and
jumbo rx producer ring sizes.  The code is then pivoted to these
variables from preprocessor constants.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3: Futureproof the loopback test

There are other multiqueue modes 5717 and 5719 devices can assume.  This
patch makes sure that the loopback test is safe, should those other
modes be enabled in the future.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3: Cleanup missing VPD partno section

This patch cleans up the default VPD partno section.  New entries for
5717 asic rev devices were also added.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3: Remove 5724 device ID

This product was never released to the public.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3: 5719: Prevent tx data corruption

This patch enables a bit that prevents read DMA overflows and adjusts
the txmbuf margin from the hardware default.  The combination of these
modifications prevents a tx data corruption issue we were seeing on the
5719.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3: Fix potential netpoll crash

Up until now the tg3 driver would call netif_napi_add() for the maximum
number of NAPI instances the driver could use.  The problem is that
netpoll could call tg3_poll() on instances that are not active.  The net
effect is that the driver will crash attempting to dereference
uninitialized pointers.

The fix is to only allocate as many NAPI instances as the driver would
use in tg3_open() and deleted them in tg3_close().

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv4: rcu conversion in ip_route_output_slow

ip_route_output_slow() is enclosed in an rcu_read_lock() protected
section, so that no references are taken/released on device, thanks to
__ip_dev_find() & dev_get_by_index_rcu()

Tested with ip route cache disabled, and a stress test :

Before patch:

elapsed time :

real 1m38.347s
user 0m11.909s
sys 23m51.501s

Profile:

13788.00 22.7% ip_route_output_slow [kernel]
 7875.00 13.0% dst_destroy          [kernel]
 3925.00  6.5% fib_semantic_match   [kernel]
 3144.00  5.2% fib_rules_lookup     [kernel]
 3061.00  5.0% dst_alloc            [kernel]
 2276.00  3.7% rt_set_nexthop       [kernel]
 1762.00  2.9% fib_table_lookup     [kernel]
 1538.00  2.5% _raw_read_lock       [kernel]
 1358.00  2.2% ip_output            [kernel]

After patch:

real 1m28.808s
user 0m13.245s
sys 20m37.293s

10950.00 17.2% ip_route_output_slow [kernel]
10726.00 16.9% dst_destroy          [kernel]
 5170.00  8.1% fib_semantic_match   [kernel]
 3937.00  6.2% dst_alloc            [kernel]
 3635.00  5.7% rt_set_nexthop       [kernel]
 2900.00  4.6% fib_rules_lookup     [kernel]
 2240.00  3.5% fib_table_lookup     [kernel]
 1427.00  2.2% _raw_read_lock       [kernel]
 1157.00  1.8% kmem_cache_alloc     [kernel]

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv4: introduce __ip_dev_find()

ip_dev_find(net, addr) finds a device given an IPv4 source address and
takes a reference on it.

Introduce __ip_dev_find(), taking a third argument, to optionally take
the device reference. Callers not asking the reference to be taken
should be in an rcu_read_lock() protected section.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: 82579 performance improvements

The initial support for 82579 was tuned poorly for performance.  Adjust the
packet buffer allocation appropriately for both standard and jumbo frames;
and for jumbo frames increase the receive descriptor pre-fetch, disable
adaptive interrupt moderation and set the DMA latency tolerance.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: use hardware writeback batching

Most e1000e parts support batching writebacks.  The problem with this is
that when some of the TADV or TIDV timers are not set, Tx can sit forever.

This is solved in this patch with write flushes using the Flush Partial
Descriptors (FPD) bit in TIDV and RDTR.

This improves bus utilization and removes partial writes on e1000e,
particularly from 82571 parts in S5500 chipset based machines.

Only ES2LAN and 82571/2 parts are included in this optimization, to reduce
testing load.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: fix link issues and panic with shared interrupts for 82598

Fix possible panic/hang with shared Legacy interrupts by not enabling
interrupts when interface is down.

Also fixes an intermittent link by enabling LSC upon exit from ixgbe_intr()

This patch adds flags to ixgbe_irq_enable() to allow for some flexibility
when enabling interrupts.

Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv4: __mkroute_output() speedup

While doing stress tests with a disabled IP route cache, I found
__mkroute_output() was touching three times in_device atomic refcount.

Use RCU to touch it once to reduce cache line ping pongs.

Before patch

time to perform the test
real 1m42.009s
user 0m12.545s
sys 25m0.726s

Profile :

16109.00 26.4% ip_route_output_slow   vmlinux
 7434.00 12.2% dst_destroy            vmlinux
 3280.00  5.4% fib_rules_lookup       vmlinux
 3252.00  5.3% fib_semantic_match     vmlinux
 2622.00  4.3% fib_table_lookup       vmlinux
 2535.00  4.1% dst_alloc              vmlinux
 1750.00  2.9% _raw_read_lock         vmlinux
 1532.00  2.5% rt_set_nexthop         vmlinux

After patch

real 1m36.503s
user 0m12.977s
sys 23m25.608s

14234.00 22.4% ip_route_output_slow   vmlinux
 8717.00 13.7% dst_destroy            vmlinux
 4052.00  6.4% fib_rules_lookup       vmlinux
 3951.00  6.2% fib_semantic_match     vmlinux
 3191.00  5.0% dst_alloc              vmlinux
 1764.00  2.8% fib_table_lookup       vmlinux
 1692.00  2.7% _raw_read_lock         vmlinux
 1605.00  2.5% rt_set_nexthop         vmlinux

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Phonet: restore flow control credits when sending fails

This patch restores the below flow control patch submitted by Rémi
Denis-Courmont, which accidentaly got lost due to Pipe controller patch
on Phonet.

commit 1a98214feef2221cd7c24b17cd688a5a9d85b2ea
Author: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Date:   Mon Aug 30 12:57:03 2010 +0000

Phonet: restore flow control credits when sending fails

Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Kumar Sanghvi <kumar.sanghvi@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: pxa168_etc.c recognize additional contributors

Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Sachin Sanap <ssanap@marvell.com>
Signed-off-by: Mark Brown <markb@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ip_gre: comments change

HARD_TX_LOCK no longer protects tunnels from dead loops,
but xmit_recursion percpu counter.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

de2104x: remove experimental status

It should be ready after 8 years...remove the experimental dependency.

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

de2104x: disable media debug messages by default

Print media debug messages only when HW debug is enabled.

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

myri10ge: DCA update (resubmit)

This patch contains the following DCA improvements to myri10ge:

1) Finally move myri10ge to use dca3 API

2) Disable PCIe relaxed ordering when enabling DCA on
     myri10ge.  This provides a performance boost on Nehalem
     based Xeons

3) Make sure to properly initialize NIC's DCA state when it is enabled,
     rather than giving the NIC a bogus tag (0) and waiting for
     the first received packet to trigger an update.  Not using a
     real tag can cause hardware exceptions on some motherboards
     when a CPU socket is empty.

3) Always update the cached CPU when our interrupt affinity changes
     so as to avoid excessive calls to dca3_get_tag()

Signed-off-by: Andrew Gallatin <gallatin@myri.com>
Signed-off-by: Loic Prylli <loic@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: Moved enabling of MSI to the bnx2x_set_num_queues()

Moved enabling of MSI to the bnx2x_set_num_queues() - the same functions that
 handles the initialization of the MSI-X.

From: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: tcp_enter_quickack_mode can be static

Function only used in tcp_input.c

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

arp: remove unnecessary export of arp_broken_ops

arp_broken_ops is only used in arp.c

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: rename netdev rx_queue to ingress_queue

There is some confusion with rx_queue name after RPS, and net drivers
private rx_queue fields.

I suggest to rename "struct net_device"->rx_queue to ingress_queue.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ip6tnl: percpu stats accounting

Maintain per_cpu tx_bytes, tx_packets, rx_bytes, rx_packets.

Other seldom used fields are kept in netdev->stats structure, possibly
unsafe.

This is a preliminary work to support lockless transmit path, and
correct RX stats, that are already unsafe.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipip: enable lockless xmits

IPIP tunnels can benefit from lockless xmits, using NETIF_F_LLTX

Bench on a 16 cpus machine (dual E5540 cpus), 16 threads sending
10000000 UDP frames via one ipip tunnel (size:200 bytes per frame)

Before patch :
real 2m53.321s
user 0m10.277s
sys 46m0.597s

After patch:
real 0m32.063s
user 0m9.237s
sys 8m16.255s

Last problem to solve is the contention on dst :

16118.00 28.3% __ip_route_output_key         vmlinux
 6135.00 10.8% dst_release                   vmlinux
 3220.00  5.6% ip_finish_output              vmlinux
 2149.00  3.8% ip_route_output_flow          vmlinux
 1575.00  2.8% ip_append_data                vmlinux
 1481.00  2.6% ip_push_pending_frames        vmlinux
 1349.00  2.4% __xfrm_lookup                 vmlinux
 1216.00  2.1% csum_partial_copy_generic     vmlinux
 1208.00  2.1% udp_sendmsg                   vmlinux

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ip_gre: lockless xmit

GRE tunnels can benefit from lockless xmits, using NETIF_F_LLTX

Note: If tunnels are created with the "oseq" option, LLTX is not
enabled :

Even using an atomic_t o_seq, we would increase chance for packets being
out of order at receiver.

Bench on a 16 cpus machine (dual E5540 cpus), 16 threads sending
10000000 UDP frames via one gre tunnel (size:200 bytes per frame)

Before patch :
real 3m0.094s
user 0m9.365s
sys 47m50.103s

After patch:
real 0m29.756s
user 0m11.097s
sys 7m33.012s

Last problem to solve is the contention on dst :

38660.00 21.4% __ip_route_output_key          vmlinux
20786.00 11.5% dst_release                    vmlinux
14191.00  7.8% __xfrm_lookup                  vmlinux
12410.00  6.9% ip_finish_output               vmlinux
 4540.00  2.5% ip_push_pending_frames         vmlinux
 4427.00  2.4% ip_append_data                 vmlinux
 4265.00  2.4% __alloc_skb                    vmlinux
 4140.00  2.3% __ip_local_out                 vmlinux
 3991.00  2.2% dev_queue_xmit                 vmlinux

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sit: enable lockless xmits

SIT tunnels can benefit from lockless xmits, using NETIF_F_LLTX

Bench on a 16 cpus machine (dual E5540 cpus), 16 threads sending
10000000 UDP frames via one sit tunnel (size:220 bytes per frame)

Before patch :

real 3m15.399s
user 0m9.185s
sys 51m55.403s

75029.00 87.5% _raw_spin_lock            vmlinux
 1090.00  1.3% dst_release               vmlinux
  902.00  1.1% dev_queue_xmit            vmlinux
  627.00  0.7% sock_wfree                vmlinux
  613.00  0.7% ip6_push_pending_frames   ipv6.ko
  505.00  0.6% __ip_route_output_key     vmlinux

After patch:

real 1m1.387s
user 0m12.489s
sys 15m58.868s

28239.00 23.3% dst_release               vmlinux
13570.00 11.2% ip6_push_pending_frames   ipv6.ko
13118.00 10.8% ip6_append_data           ipv6.ko
 7995.00  6.6% __ip_route_output_key     vmlinux
 7924.00  6.5% sk_dst_check              vmlinux
 5015.00  4.1% udpv6_sendmsg             ipv6.ko
 3594.00  3.0% sock_alloc_send_pskb      vmlinux
 3135.00  2.6% sock_wfree                vmlinux
 3055.00  2.5% ip6_sk_dst_lookup         ipv6.ko
 2473.00  2.0% ip_finish_output          vmlinux

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sit: fix percpu stats accounting

commit 15fc1f7056ebd (sit: percpu stats accounting) forgot the fallback
tunnel case (sit0), and can crash pretty fast.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipip: fix percpu stats accounting

commit 3c97af99a5aa1 (ipip: percpu stats accounting) forgot the fallback
tunnel case (tunl0), and can crash pretty fast.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dummy: percpu stats and lockless xmit

Converts dummy network device driver to :

- percpu stats

- 64bit stats

- lockless xmit (NETIF_F_LLTX)

- performance features added (NETIF_F_SG | NETIF_F_FRAGLIST |
NETIF_F_TSO | NETIF_F_NO_CSUM | NETIF_F_HIGHDMA)

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: add a recursion limit in xmit path

As tunnel devices are going to be lockless, we need to make sure a
misconfigured machine wont enter an infinite loop.

Add a percpu variable, and limit to three the number of stacked xmits.

Reported-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: Implement Any-IP support for IPv6.

AnyIP is the capability to receive packets and establish incoming
connections on IPs we have not explicitly configured on the machine.

An example use case is to configure a machine to accept all incoming
traffic on eth0, and leave the policy of whether traffic for a given IP
should be delivered to the machine up to the load balancer.

Can be setup as follows:
  ip -6 rule from all iif eth0 lookup 200
  ip -6 route add local default dev lo table 200
(in this case for all IPv6 addresses)

Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv4: Allow configuring subnets as local addresses

This patch allows a host to be configured to respond to any address in
a specified range as if it were local, without actually needing to
configure the address on an interface.  This is done through routing
table configuration.  For instance, to configure a host to respond
to any address in 10.1/16 received on eth0 as a local address we can do:

ip rule add from all iif eth0 lookup 200
ip route add local 10.1/16 dev lo proto kernel scope host src 127.0.0.1 table 200

This host is now reachable by any 10.1/16 address (route lookup on
input for packets received on eth0 can find the route).  On output, the
rule will not be matched so that this host can still send packets to
10.1/16 (not sent on loopback).  Presumably, external routing can be
configured to make sense out of this.

To make this work, we needed to modify the logic in finding the
interface which is assigned a given source address for output
(dev_ip_find).  We perform a normal fib_lookup instead of just a
lookup on the local table, and in the lookup we ignore the input
interface for matching.

This patch is useful to implement IP-anycast for subnets of virtual
addresses.

Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

pch_gbe: add header files

Fix build errors, more header files needed.

drivers/net/pch_gbe/pch_gbe_main.c:965: error: implicit declaration of function 'tcp_hdr'
drivers/net/pch_gbe/pch_gbe_main.c:965: error: invalid type argument of '->' (have 'int')
drivers/net/pch_gbe/pch_gbe_main.c:968: error: invalid type argument of '->' (have 'int')
drivers/net/pch_gbe/pch_gbe_main.c:976: error: implicit declaration of function 'udp_hdr'
drivers/net/pch_gbe/pch_gbe_main.c:976: error: invalid type argument of '->' (have 'int')
drivers/net/pch_gbe/pch_gbe_main.c:980: error: invalid type argument of '->' (have 'int')

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Documentation: Update Phonet doc for Pipe Controller implementation

Updates the Phonet document with description related to Pipe controller
implementation

Signed-off-by: Kumar Sanghvi <kumar.sanghvi@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3: Use netif_set_real_num_{rx,tx}_queues()

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8021q: Use netif_copy_real_num_queues() to set queue counts

This covers RX if necessary, as well as TX.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: Use netif_set_real_num_{rx,tx}_queues()

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

niu: Use netif_set_real_num_{rx,tx}_queues()

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

myri10ge: Use netif_set_real_num_{rx, tx}_queues()

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mv643xx_eth: Use netif_set_real_num_{rx, tx}_queues()

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlx4_en: Use netif_set_real_num_{rx, tx}_queues()

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: Use netif_set_real_num_{rx,tx}_queues()

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

igb: Use netif_set_real_num_{rx,tx}_queues()

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

gianfar: Use netif_set_real_num_rx_queues()

Do not set num_tx_queues or real_num_tx_queues, since
alloc_etherdev_mq() does that.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cxgb4vf: Use netif_set_real_num_{rx, tx}_queues()

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cxgb4: Use netif_set_real_num_{rx,tx}_queues()

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cxgb3: Use netif_set_real_num_{rx,tx}_queues()

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: Use netif_set_real_num_{rx,tx}_queues()

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2: Use netif_set_real_num_{rx,tx}_queues()

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Add netif_copy_real_num_queues() for use by virtual net drivers

This sets the active numbers of queues on a net device to match another.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Allow changing number of RX queues after device allocation

For RPS, we create a kobject for each RX queue based on the number of
queues passed to alloc_netdev_mq().  However, drivers generally do not
determine the numbers of hardware queues to use until much later, so
this usually represents the maximum number the driver may use and not
the actual number in use.

For TX queues, drivers can update the actual number using
netif_set_real_num_tx_queues().  Add a corresponding function for RX
queues, netif_set_real_num_rx_queues().

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sk_{detach|attach}_filter() rcu fixes

sk_attach_filter() and sk_detach_filter() are run with socket locked.

Use the appropriate rcu_dereference_protected() instead of blocking BH,
and rcu_dereference_bh().
There is no point adding BH prevention and memory barrier.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fib: use atomic_inc_not_zero() in fib_rules_lookup

It seems we dont use appropriate refcount increment in an
rcu_read_lock() protected section.

fib_rule_get() might increment a null refcount and bad things could
happen.

While fib_nl_delrule() respects an rcu grace period before calling
fib_rule_put(), fib_rules_cleanup_ops() calls fib_rule_put() without a
grace period.

Note : after this patch, we might avoid the synchronize_rcu() call done
in fib_nl_delrule()

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sit: percpu stats accounting

Maintain per_cpu tx_bytes, tx_packets, rx_bytes, rx_packets.

Other seldom used fields are kept in netdev->stats structure, possibly
unsafe.

This is a preliminary work to support lockless transmit path, and
correct RX stats, that are already unsafe.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipip: percpu stats accounting

Maintain per_cpu tx_bytes, tx_packets, rx_bytes, rx_packets.

Other seldom used fields are kept in netdev->stats structure, possibly
unsafe.

This is a preliminary work to support lockless transmit path, and
correct RX stats, that are already unsafe.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ip_gre: percpu stats accounting

Le lundi 27 septembre 2010 à 14:29 +0100, Ben Hutchings a écrit :

> > diff --git a/net/ipv4/ip_gre.c b/net/ipv4/ip_gre.c
> > index 5d6ddcb..de39b22 100644
> > --- a/net/ipv4/ip_gre.c
> > +++ b/net/ipv4/ip_gre.c
> [...]
> > @@ -377,7 +405,7 @@ static struct ip_tunnel *ipgre_tunnel_locate(struct net *net,
> >   if (parms->name[0])
> >   strlcpy(name, parms->name, IFNAMSIZ);
> >   else
> > - sprintf(name, "gre%%d");
> > + strcpy(name, "gre%d");
> >
> >   dev = alloc_netdev(sizeof(*t), name, ipgre_tunnel_setup);
> >   if (!dev)
> [...]
>
> This is a valid fix, but doesn't belong in this patch!
>

Sorry ? It was not a fix, but at most a cleanup ;)

Anyway I forgot the gretap case...

[PATCH 2/4 v2] ip_gre: percpu stats accounting

Maintain per_cpu tx_bytes, tx_packets, rx_bytes, rx_packets.

Other seldom used fields are kept in netdev->stats structure, possibly
unsafe.

This is a preliminary work to support lockless transmit path, and
correct RX stats, that are already unsafe.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tunnels: prepare percpu accounting

Tunnels are going to use percpu for their accounting.

They are going to use a new tstats field in net_device.

skb_tunnel_rx() is changed to be a wrapper around __skb_tunnel_rx()

IPTUNNEL_XMIT() is changed to be a wrapper around __IPTUNNEL_XMIT()

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vlan: use this_cpu_ptr() in vlan_skb_recv()

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Phonet: Implement Pipe Controller to support Nokia Slim Modems

Phonet stack assumes the presence of Pipe Controller, either in Modem or
on Application Processing Engine user-space for the Pipe data.
Nokia Slim Modems like WG2.5 used in ST-Ericsson U8500 platform do not
implement Pipe controller in them.
This patch adds Pipe Controller implemenation to Phonet stack to support
Pipe data over Phonet stack for Nokia Slim Modems.

Signed-off-by: Kumar Sanghvi <kumar.sanghvi@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of /linux/kernel/git/davem/net-2.6

Conflicts:
drivers/net/qlcnic/qlcnic_init.c
net/ipv4/ip_output.c

net: r6040: store BIOS default MAC in perm_add

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: add a missing unregister_pernet_subsys call

Clean up a missing exit path in the ipv6 module init routines.  In
addrconf_init we call ipv6_addr_label_init which calls register_pernet_subsys
for the ipv6_addr_label_ops structure.  But if module loading fails, or if the
ipv6 module is removed, there is no corresponding unregister_pernet_subsys call,
which leaves a now-bogus address on the pernet_list, leading to oopses in
subsequent registrations.  This patch cleans up both the failed load path and
the unload path.  Tested by myself with good results.

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
 include/net/addrconf.h |    1 +
 net/ipv6/addrconf.c    |   11 ++++++++---
 net/ipv6/addrlabel.c   |    5 +++++
 3 files changed, 14 insertions(+), 3 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>

net: loopback driver cleanup

loopback driver uses dev->ml_priv to store its percpu stats pointer.
It uses ugly casts "(void __percpu __force *)" to shut up sparse
complains.

Define an union to better document we use ml_priv in loopback driver and
define a lstats field with appropriate types.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fix rcu use in ip_route_output_slow

__in_dev_get_rtnl(dev_out) is called while RTNL is not held, thus
triggers a lockdep fault.

At this point, we only perform a raw test of dev_out->ip_ptr being NULL,
we dont need to make sure ip_ptr cant changed right after.

We can use rcu_dereference_raw() for this.

Reported-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rps: allocate rx queues in register_netdevice only

Instead of having two places were we allocate dev->_rx, introduce
netif_alloc_rx_queues() helper and call it only from
register_netdevice(), not from alloc_netdev_mq()

Goal is to let drivers change dev->num_rx_queues after allocating netdev
and before registering it.

This also removes a lot of ifdefs in net/core/dev.c

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s390: use free_netdev(netdev) instead of kfree()

Freeing netdev without free_netdev() leads to net, tx leaks.
I might lead to dereferencing freed pointer.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

@@
struct net_device* dev;
@@

-kfree(dev)
+free_netdev(dev)

Signed-off-by: David S. Miller <davem@davemloft.net>

sgiseeq: use free_netdev(netdev) instead of kfree()

Freeing netdev without free_netdev() leads to net, tx leaks.
I might lead to dereferencing freed pointer.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

@@
struct net_device* dev;
@@

-kfree(dev)
+free_netdev(dev)

Signed-off-by: David S. Miller <davem@davemloft.net>

rionet: use free_netdev(netdev) instead of kfree()

Freeing netdev without free_netdev() leads to net, tx leaks.
I might lead to dereferencing freed pointer.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

@@
struct net_device* dev;
@@

-kfree(dev)
+free_netdev(dev)

Signed-off-by: David S. Miller <davem@davemloft.net>

ibm_newemac: use free_netdev(netdev) instead of kfree()

Freeing netdev without free_netdev() leads to net, tx leaks.
I might lead to dereferencing freed pointer.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

@@
struct net_device* dev;
@@

-kfree(dev)
+free_netdev(dev)

Signed-off-by: David S. Miller <davem@davemloft.net>

net: update SOCK_MIN_RCVBUF

SOCK_MIN_RCVBUF current value is 256 bytes

It doesnt permit to receive the smallest possible frame, considering
socket sk_rmem_alloc/sk_rcvbuf account skb truesizes. On 64bit arches,
sizeof(struct sk_buff) is 240 bytes. Add the typical 64 bytes of
headroom, and we go over the limit.

With old kernels and 32bit arches, we were under the limit, if netdriver
was doing copybreak.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

smsc911x: Add MODULE_ALIAS()

This enables auto loading for the smsc911x ethernet driver.

Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: reset skb queue mapping when rx'ing over tunnel

Reset queue mapping when an skb is reentering the stack via a tunnel.
On second pass, the queue mapping from the original device is no
longer valid.

Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net: return operator cleanup

Change "return (EXPR);" to "return EXPR;"

return is not a function, parentheses are not required.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: skb_frag_t can be smaller on small arches

On 32bit arches, if PAGE_SIZE is smaller than 65536, we can use 16bit
offset and size fields. This patch saves 72 bytes per skb on i386, or
128 bytes after rounding.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

br2684: fix scheduling while atomic

You can't call atomic_notifier_chain_unregister() while in atomic context.

Fix, call un/register_atmdevice_notifier in module __init and __exit.

Bug report:
http://comments.gmane.org/gmane.linux.network/172603

Reported-by: Mikko Vinni <mmvinni@yahoo.com>
Tested-by: Mikko Vinni <mmvinni@yahoo.com>
Signed-off-by: Karl Hiramoto <karl@hiramoto.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: propagate NETIF_F_HIGHDMA to vlans

Automatically allows vlans to get NETIF_F_HIGHDMA if underlying device
supports it.

On 32bit arches (and more precisely if CONFIG_HIGHMEM is enabled), it
can help to reduce cost of illegal_highdma() and __skb_linearize()
calls.

Tested on tg3 , bnx2, bonding, this worked very well.

This is a generalization of a patch provided by Yi Zou & Jeff Kirsher.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

de2104x: fix TP link detection

Compex FreedomLine 32 PnP-PCI2 cards have only TP and BNC connectors but the
SROM contains AUI port too. When TP loses link, the driver switches to
non-existing AUI port (which reports that carrier is always present).

Connecting TP back generates LinkPass interrupt but de_media_interrupt() is
broken - it only updates the link state of currently connected media, ignoring
the fact that LinkPass and LinkFail bits of MacStatus register belong to the
TP port only (the chip documentation says that).

This patch changes de_media_interrupt() to switch media to TP when link goes
up (and media type is not locked) and also to update the link state only when
the TP port is used.

Also the NonselPortActive (and also SelPortActive) bits of SIAStatus register
need to be cleared (by writing 1) after reading or they're useless.

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

de2104x: fix power management

At least my 21041 cards come out of suspend with bus mastering disabled so
they did not work after resume(no data transferred).
After adding pci_set_master(), the driver oopsed immediately on resume -
because de_clean_rings() is called on suspend but de_init_rings() call
was missing in resume.

Also disable link (reset SIA) before sleep (de4x5 does this too).

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbevf: Refactor ring parameter re-size

The function to resize the Tx/Rx rings had the potential to
dereference a NULL pointer and the code would attempt to resize
the Tx ring even if the Rx ring allocation had failed.  This
would cause some confusion in the return code semantics.  Fixed
up to just unwind the allocations if any of them fail and return
an error.

Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

de2104x: disable autonegotiation on broken hardware

At least on older 21041-AA chips (mine is rev. 11), TP duplex autonegotiation
causes the card not to work at all (link is up but no packets are transmitted).

de4x5 disables autonegotiation completely. But it seems to work on newer
(21041-PA rev. 21) so disable it only on rev<20 chips.

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fix a lockdep splat

We have for each socket :

One spinlock (sk_slock.slock)
One rwlock (sk_callback_lock)

Possible scenarios are :

(A) (this is used in net/sunrpc/xprtsock.c)
read_lock(&sk->sk_callback_lock) (without blocking BH)
<BH>
spin_lock(&sk->sk_slock.slock);
...
read_lock(&sk->sk_callback_lock);
...

(B)
write_lock_bh(&sk->sk_callback_lock)
stuff
write_unlock_bh(&sk->sk_callback_lock)

(C)
spin_lock_bh(&sk->sk_slock)
...
write_lock_bh(&sk->sk_callback_lock)
stuff
write_unlock_bh(&sk->sk_callback_lock)
spin_unlock_bh(&sk->sk_slock)

This (C) case conflicts with (A) :

CPU1 [A]                         CPU2 [C]
read_lock(callback_lock)
<BH>                             spin_lock_bh(slock)
<wait to spin_lock(slock)>
                                 <wait to write_lock_bh(callback_lock)>

We have one problematic (C) use case in inet_csk_listen_stop() :

local_bh_disable();
bh_lock_sock(child); // spin_lock_bh(&sk->sk_slock)
WARN_ON(sock_owned_by_user(child));
...
sock_orphan(child); // write_lock_bh(&sk->sk_callback_lock)

lockdep is not happy with this, as reported by Tetsuo Handa

It seems only way to deal with this is to use read_lock_bh(callbacklock)
everywhere.

Thanks to Jarek for pointing a bug in my first attempt and suggesting
this solution.

Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Tested-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Jarek Poplawski <jarkao2@gmail.com>
Tested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

stmmac: review the wake-up support

If the PM support is available this is passed
through the platform instead to be hard-coded
in the core files.
WoL on Magic Frame can be enabled by using
the ethtool support.

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Add Gigabit Ethernet driver of Topcliff PCH

Signed-off-by: Masayuki Ohtake <masa-korg@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>