David Bauer [Sat, 12 Jun 2021 22:05:59 +0000 (00:05 +0200)]
apm821xx: move CONFIG_REGULATOR to target config
This moves CONFIG_REGULATOR to the target config instead of the
subtarget config.
For kernel 5.10, CONFIG_AT803X_PHY depends on CONFIG_REGULATOR.
As we do not have a size constraint, move this symbol to the
target configuration for kernel 5.4 as well as 5.10.
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Sat, 12 Jun 2021 11:12:40 +0000 (13:12 +0200)]
generic: kernel 5.4: fix probe error for AR803x PHYs
Atheros PHYs using the at803x driver apart from the AR8031/AR8033 fail
to probe with kernel 5.4, due to ret in at803x_probe being
uninitialized.
[ 1.403461] Atheros 8035 ethernet: probe of
4ef600c00.ethernet:01
failed with error -
1066114012
Initialize ret in order to successfully prove the PHYs on kernel 5.4.
Kernel 5.10 is not affected, as the ret is always assigned prior to
returning.
Tested on OCEDO Koala.
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: David Bauer <mail@david-bauer.net>
Amish Vishwakarma [Sat, 5 Jun 2021 07:01:00 +0000 (12:31 +0530)]
ramips: add support for TP-Link Archer C6 v3
The patch adds support for the TP-Link Archer C6 v3 (FCC ID TE7A6V3)
The patch adds identification changes to the existing TP-Link Archer A6,
by Vinay Patil <post2vinay@gmail.com>, which has identical hardware.
Specification
-------------
MediaTek MT7621 SOC
RAM: 128MB DDR3
SPI Flash: W25Q128 (16MB)
Ethernet: MT7530 5x 1000Base-T
WiFi 5GHz: Mediatek MT7613BE
WiFi 2.4GHz: Mediatek MT7603E
UART/Serial: 115200 8n1
Device Configuration & Serial Port Pins
---------------------------------------
ETH Ports: LAN4 LAN3 LAN2 LAN1 WAN
_______________________
| |
Serial Pins: | VCC GND TXD RXD |
|_____________________|
LEDs: Power Wifi2G Wifi5G LAN WAN
Build Output
------------
The build will generate following set of files
[1] openwrt-ramips-mt7621-tplink_archer-c6-v3-initramfs-kernel.bin
[2] openwrt-ramips-mt7621-tplink_archer-c6-v3-squashfs-factory.bin
[3] openwrt-ramips-mt7621-tplink_archer-c6-v3-squashfs-sysupgrade.bin
How to Use - Flashing from TP-Link Web Interface
------------------------------------------------
* Go to "Advanced/System Tools/Firmware Update".
* Click "Browse" and upload the OpenWrt factory image: factory.bin[2]
* Click the "Upgrade" button, and select "Yes" when prompted.
TFTP Booting
------------
Setup a TFTP boot server with address 192.168.0.5.
While starting U-boot press '4' key to stop autoboot.
Copy the initramfs-kernel.bin[1] to TFTP server folder, rename as test.bin
From u-boot command prompt run tftpboot followed by bootm.
Recovery
--------
Archer A6 V3 has recovery page activated if SPI booting from flash fails.
Recovery page can be activated by powercycling the router four times
before the boot process is complete.
Note: TFTP boot can be activated only from u-boot serial console.
Device recovery address: 192.168.0.1
Signed-off-by: Amish Vishwakarma <vishwakarma.amish@gmail.com>
[fix indent]
Signed-off-by: David Bauer <mail@david-bauer.net>
Rosen Penev [Sat, 12 Jun 2021 23:02:29 +0000 (16:02 -0700)]
prereq-build: diff requirement to GNU
tools/quilt requires GNU diffutils to compile. Failure can be simulated
by installing Alpine Linux without diffutils.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Michael Pratt [Sat, 29 May 2021 13:03:11 +0000 (09:03 -0400)]
base-files: upgrade: use procd to kill managed daemons
These processes are managed by procd and set to start again when killed
via the procd instance parameter "respawn" being set during init.
Example:
procd_set_param respawn 3600 1 0
When they are killed manually during sysupgrade,
they are started again in 5 seconds or less, depending on
how the "respawn" parameter is set.
Use procd through ubus to disable the instances that respawn them,
however, allow dnsmasq, netifd, and logd to restart for remote logging.
Properly closing all these processes increases free memory by about 3 MB,
which should help low memory devices upgrade without crashing.
For very low memory devices (set to 32 MB for now)
also kill dnsmasq, netifd, and logd for an additional 3 MB of free memory.
Also, bump sleep values to allow at least 10 seconds
for network interfaces and daemons
to come up after they are killed and restarted
before caches are dropped.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Paul Spooren [Sat, 12 Jun 2021 22:38:30 +0000 (12:38 -1000)]
README: switch from freenode to oftc
We recently switched from freenode.net to oftc.net, reflect that in the
README and update the links.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Paul Spooren [Sat, 12 Jun 2021 18:27:16 +0000 (08:27 -1000)]
README: update routing.git URL
The routing packages feed moved from `openwrt-routing/packages` to
`openwrt/routing`, reflect that in the README.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Felix Fietkau [Sat, 12 Jun 2021 12:32:41 +0000 (14:32 +0200)]
build: do not override DESTDIR for cmake ninja host builds
The full prefix is already passed to cmake
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Sat, 12 Jun 2021 12:24:40 +0000 (14:24 +0200)]
tools: build ninja before ccache to fix the build order
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Sat, 12 Jun 2021 10:40:02 +0000 (12:40 +0200)]
tools: fix dependencies of cmake packages
Make cmake depend on ninja, so that other cmake based tools also depend on it
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Thu, 10 Jun 2021 12:01:04 +0000 (14:01 +0200)]
build: use ninja for cmake packages by default
Speed goes from:
Executed in 178.08 secs fish external
usr time 20.16 mins 509.00 micros 20.16 mins
sys time 2.88 mins 39.00 micros 2.88 mins
To:
Executed in 175.90 secs fish external
usr time 20.19 mins 0.00 micros 20.19 mins
sys time 2.85 mins 497.00 micros 2.85 mins
Tested with "time make -j 12" on AMD Ryzen 3600
When building individual packages, the build time difference is often
significantly bigger than that.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Sun, 6 Jun 2021 21:24:43 +0000 (14:24 -0700)]
package: fix cmake packages build with ninja
+= is needed for CMAKE_OPTIONS.
mt76 needs Ninja disabled as the kernel stuff uses normal make.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Felix Fietkau [Sun, 6 Jun 2021 12:31:01 +0000 (14:31 +0200)]
build: add ninja build tool and make it available for cmake
ninja is faster at building cmake packages than make, and according to reports
also more reliable at handling parallel builds
This commit includes a patch that adds GNU make jobserver support, in order to
allow more precise control over the number of parallel tasks
Enable parallel build by default for packages using ninja
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Felix Fietkau [Sat, 29 Aug 2020 20:24:59 +0000 (22:24 +0200)]
u-boot: support verbose build
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Sun, 6 Jun 2021 18:58:33 +0000 (20:58 +0200)]
mac80211: add support for 802.3 encap offload with software rate control
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Sun, 6 Jun 2021 18:57:39 +0000 (20:57 +0200)]
mac80211: improve rate control performance
Call rate control handler after intermediate queueuing
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Tianling Shen [Fri, 25 Dec 2020 12:03:14 +0000 (20:03 +0800)]
rockchip: add NanoPi R4S support
Hardware
--------
RockChip RK3399 ARM64 (6 cores)
4GB LPDDR4 RAM
2x 1000 Base-T
3 LEDs (LAN / WAN / SYS)
1 Button (Reset)
Micro-SD slot
2x USB 3.0 Port
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card using
dd.
=====================================
NOTICE FOR USERS WHO USE 1GB VERSION:
BY NOW IT IS NOT SUPPORTED
====================================
[initialed target]
Co-developed-by: Marty Jones <mj8263788@gmail.com>
Signed-off-by: Marty Jones <mj8263788@gmail.com>
[fixed bootscript]
Co-developed-by: Jayantajit Gogoi <jayanta.gogoi525@gmail.com>
Signed-off-by: Jayantajit Gogoi <jayanta.gogoi525@gmail.com>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Tianling Shen [Thu, 13 May 2021 13:49:59 +0000 (21:49 +0800)]
uboot-rockchip: add NanoPi R4S support
Add support for the FriendlyARM NanoPi R4S.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Chris Blake [Wed, 9 Jun 2021 12:23:11 +0000 (07:23 -0500)]
x86: add upgrade support to diag.sh
Similar to how this is done in the diag.sh found in the base-files
package, we should blink our status LED (if we have one) during the
upgrade process. This follows the same blink pattern as seen at
./package/base-files/files/etc/diag.sh#L36
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Felix Fietkau [Wed, 9 Jun 2021 12:32:32 +0000 (14:32 +0200)]
mac80211: rely on iwinfo for phy->path and path->phy lookups
This avoids inconsistencies from having multiple implementations do the same thing
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Thu, 10 Jun 2021 06:52:28 +0000 (08:52 +0200)]
iwinfo: update to the latest version
aa0e3c4bbe12 iwinfo: nl80211: add support for printing the device path for a phy
dd6d6d2dec35 iwinfo: nl80211: use new path lookup function for nl80211_phy_idx_from_uci_path
268bb26d2e2a iwinfo: nl80211: support looking up phy by path=.. and macaddr=...
c0414642fead iwinfo: nl80211: fix typo
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Adam Elyas [Tue, 8 Jun 2021 00:09:18 +0000 (08:09 +0800)]
ramips: fix LAN LED trigger assignment for Xiaomi Router 3 Pro
The default trigger for the amber lights on lan1 and lan3 were
mistakenly swapped after the device's migration to DSA. This
caused activity on one port to trigger the amber light on the
other port. Swapping their default trigger in the DTS file
fixes that.
Signed-off-by: Adam Elyas <adamelyas@outlook.com>
[minor commit title adjustment, wrap commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Pawel Dembicki [Wed, 9 Jun 2021 10:52:51 +0000 (12:52 +0200)]
ramips: mt7620: disable Jboot devices build
At this moment kernel size in mt7620 snapshot builds is bigger than 2048k.
It should be disabled by default.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Pawel Dembicki [Wed, 9 Jun 2021 10:22:39 +0000 (12:22 +0200)]
ramips: mt7620: add kernel size for Jboot devices
Since few months multiple users reported problems with various JBoot
devices. [0][1][2][3] All of them was bricked.
On my Lava LR-25G001 it freezes with current snapshot:
CDW57CAM_003 Jboot B695
Giga Switch AR8327 init
AR8327/AR8337 id ==> 0x1302
JRecovery Version R1.2 2014/04/01 18:25
SPI FLASH: MX25l12805d 16M
.
.
(freeze)
The kernel size is >2048k.
I built current master with minimal config and it boots well:
CDW57CAM_003 Jboot B695
Giga Switch AR8327 init
AR8327/AR8337 id ==> 0x1302
JRecovery Version R1.2 2014/04/01 18:25
SPI FLASH: MX25l12805d 16M
.
...........................
Starting kernel @
80000000...
[ 0.000000] Linux version 5.4.124
Kernel size is <2048k.
Jboot bootloader isn't open source, so it's impossible to find
solution in code. It looks, that some buffer for kernel have 2MB size.
To avoid bricked devices, this commit introduces 2048k limit kernel
size for all jboot routers.
[0] https://bugs.openwrt.org/index.php?do=details&task_id=3539
[1] https://eko.one.pl/forum/viewtopic.php?pid=254344
[2] https://eko.one.pl/forum/viewtopic.php?id=20930
[3] https://eko.one.pl/forum/viewtopic.php?pid=241376#p241376
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[remove Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Liu Yu [Tue, 8 Jun 2021 01:50:02 +0000 (09:50 +0800)]
ramips: fix Ethernet random MAC address for HILINK HLK-7628N
Set the ethernet address from flash.
MAC addresses as verified by OEM firmware:
use interface source
2g wlan0 factory 0x04 (label)
LAN eth0.1 factory 0x28 (label+1)
WAN eth0.2 factory 0x2e (label+2)
Fixes: 671c9d16e382 ("ramips: add support for HILINK HLK-7628N")
Signed-off-by: Liu Yu <f78fk@live.com>
[drop old MAC address setup from 02_network, cut out state_default
changes, face-lift commit message, add Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Felix Fietkau [Wed, 9 Jun 2021 11:16:11 +0000 (13:16 +0200)]
toolchain/gdb: fix broken non-python build
Append configure args instead of overwriting them
Fixes: 74417f8b3a80 ("toolchain: gdb: Add optional python support")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
David Bauer [Tue, 8 Jun 2021 17:30:12 +0000 (19:30 +0200)]
build: fix build for devices without initramfs
Don't attempt to copy initramfs images for devices which do not output
an initramfs image.
This was breaking builds for mpc85xx-p1010 since mid-march.
Signed-off-by: David Bauer <mail@david-bauer.net>
Karel Kočí [Thu, 11 Feb 2021 09:57:06 +0000 (10:57 +0100)]
scripts/feeds: generate index after all feeds are updated
This separates index update from feed update. The result is that all
requested feeds are first updated and only then indexed.
The reason for this change is to prevent errors being reported and
potentially invalid index being generated thanks to cross feeds
dependency.
The feeds script pulls in default all feeds as they come and on install
prefers packages from first feeds (unless special feed is requested).
Thus order of feeds in some way specifies preferences. This is handy for
downstream distributions as they can simply override any package from
upstream feeds by placing their feed before them. This removes need to
patch or fork upstream feeds.
The problem is that such feed most likely depends in some way also on
subsequent feeds. The most likely feeds are 'packages' or 'luci'. The
example would be Python package that needs 'python.mk' from 'packages'
feed. Ordering custom feed after dependent feeds is sometimes just not
possible because of preference requirement described before.
The solution is to just first pull all feeds and generate indexes only
after that. In the end this ensures that index is generated correctly at
first try without any error.
In terms of code this removes 'perform_update' argument from
'update_feed' as with index update removal the update is the only action
performed in that subroutine. Thus this moves condition to 'update'
subroutine.
Signed-off-by: Karel Kočí <karel.koci@nic.cz>
David Bauer [Sun, 6 Jun 2021 23:05:24 +0000 (01:05 +0200)]
ramips: fix patch location
The patch for adding the config_aneg function for the Atheros
AR8031/AR8033 PHY was formatted in a way it moved to different PHY
models while refreshing patches on kernel updates.
Move the diff directly below the PHY name so this won't happen in the
future.
Signed-off-by: David Bauer <mail@david-bauer.net>
Gaspare Bruno [Wed, 13 Jan 2021 21:03:39 +0000 (18:03 -0300)]
ramips: mt7620: enable autonegotiation for all ports
This enables autonegotiation for all ephy ports on probe.
Some devices do not configure the ports, particularly port 4.
Signed-off-by: Gaspare Bruno <gaspare@anlix.io>
[replace magic values ; reword commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Sun, 6 Jun 2021 17:45:24 +0000 (19:45 +0200)]
ramips: make PHY initialization more descriptive
The basic mode control register of the ESW PHYs is modified in this
codeblock. Use the respective macros to make this code more readable.
Signed-off-by: David Bauer <mail@david-bauer.net>
Tomas Lara [Tue, 1 Jun 2021 18:00:15 +0000 (14:00 -0400)]
linux-firmware: update to
20210511
git log --pretty=oneline --abbrev-commit
20201118..
20210511
7685cf4 (HEAD, tag:
20210511) nvidia: Update Tegra194 XUSB firmware to v60.09
cf32752 nvidia: Update Tegra186 XUSB firmware to v55.18
cb8ca82 nvidia: Update Tegra210 XUSB firmware to v50.26
f99d6a1 linux-firmware: update firmware for mhdp8546
ecdfcf8 Merge branch 'adlp_dmc_firmware' of git://anongit.freedesktop.org/drm/drm-firmware into main
547b202 Merge https://github.com/suraj714/linux-firmware-venus into main
3d32f21 i915: Add ADL-P DMC Support
3f23f51 amdgpu: add new polaris 12 MC firmware
a2565bb firmware: nvidia: Add VIC firmware for Tegra194
17ec2a5 qcom: add gpu firmwares for sc7280
b653cf4 Merge https://github.com/pkshih/linux-firmware into main
2a96c08 brcm: Add a link to enable khadas VIM2's WiFi
ffc64a2 rtw89: 8852a: update fw to v0.13.8.0
3e3497c rtl_bt: Update RTL8852A BT USB firmware to 0xD9A8_7893
c7b11ed qcom: Add venus firmware files for VPU-2.0
2f4f0f8 rtw89: 8852a: update fw to v0.13.8.0
fa0efef linux-firmware: Update firmware file for Intel Bluetooth AX210
9be3daa linux-firmware: Update firmware file for Intel Bluetooth 9560
687d64a linux-firmware: Update firmware file for Intel Bluetooth 9260
a7f1249 linux-firmware: Update firmware file for Intel Bluetooth AX200
47650a0 linux-firmware: Update firmware file for Intel Bluetooth AX201
195ecf1 linux-firmware: Intel BT 7265: Fix Security Issues
4116d72 linux-firmware: Update firmware file for Intel Bluetooth 8265
ca83c73 qcom: update venus firmware files for v5.4
1334578 Merge branch 'mrvl-prestera' of https://github.com/PLVision/linux-firmware into main
16052e4 mrvl: prestera: Add Marvell Prestera Switchdev firmware 3.0 version
bdf929d rtw88: 8822c: Update normal firmware to v9.9.9
0b558e8 brcm: add missing symlink for Pi Zero W NVRAM file
cfa004c amdgpu: update arcturus firmware from 21.10
d5567c5 amdgpu: update navy flounder firmware from 21.10
ef5ea5d amdgpu: update sienna cichlid firmware from 21.10
f35700f amdgpu: update vega20 firmware from 21.10
1be98f1 amdgpu: update picasso firmware from 21.10
fee0497 amdgpu: update navi14 firmware from 21.10
15003b0 amdgpu: update green sardine firmware from 21.10
64555fb amdgpu: update vega12 firmware from 21.10
eb07276 amdgpu: update navi12 firmware from 21.10
e36c82a amdgpu: update vega10 firmware from 21.10
4a5eaa2 amdgpu: update renoir firmware from 21.10
65eb326 amdgpu: update navi10 firmware from 21.10
8bdca03 amdgpu: update raven2 firmware from 21.10
c9e44ca amdgpu: update raven firmware from 21.10
bc3e610 rtl_nic: add new firmware for RTL8153 and RTL8156 series
8528618 Merge branch 'for-upstream' of git://git.chelsio.net/pub/git/linux-firmware into main
940b7f4 cxgb4: Update firmware to revision 1.25.4.0
f66adc3 Merge branch 'main' of gitolite.kernel.org:/pub/scm/linux/kernel/git/maks/linux-firmware into main
f350e91 Merge https://github.com/rjliao-qca/qca-btfw into main
9bc1bcc Merge https://github.com/Netronome/linux-firmware into main
2f30708 Mellanox: Add new mlxsw_spectrum firmware xx.2008.2438
393f272 brcm: Link CM4's WiFi firmware with DMI machine name.
73144e0 linux-firmware: Update firmware file for Intel Bluetooth AX201
8ab7aba amdgpu: update navi14 smc firmware
4fe6e53 amdgpu: update navi10 SMC firmware
c296849 QCA: Update Bluetooth firmware for QCA6174
d6a18e9 WHENCE: link to similar config file for rtl8821a support
6c419ae nfp: update Agilio SmartNIC flower firmware to rev AOTC-2.14.A.6
af1ca28 amdgpu: add arcturus firmware
0dd245d Merge branch 'sm8250-new-fw' of https://github.com/lumag/linux-firmware into main
55cab07 rtl_bt: Add rtl8723bs_config-OBDA0623.bin symlink
2548d06 brcm: Add nvram for the Chuwi Hi8 (CWI509) tablet
e45c137 brcm: Add nvram for the Predia Basic tablet
d8fa0cf qcom: sm8250: update remoteproc firmware
84af0e0 qcom: update a650 firmware files
3f026a2 rtl_bt: Update RTL8822C BT(UART I/F) FW to 0x59A_76A3
c82cb46 amdgpu: update sienna cichlid firmware for 20.50
24fe696 amdgpu: update vega20 firmware for 20.50
e05d197 amdgpu: update picasso firmware for 20.50
76d07cd amdgpu: update navi14 firmware for 20.50
b2fc037 amdgpu: update vega12 firmware for 20.50
25451a4 amdgpu: update navi12 firmware for 20.50
b938597 amdgpu: update vega10 firmware for 20.50
2542ba7 amdgpu: update renoir firmware for 20.50
b55d063 amdgpu: update navi10 firmware for 20.50
1a62f28 amdgpu: update raven2 firmware for 20.50
4df488f amdgpu: update raven firmware for 20.50
a29bdb2 amdgpu: add initial support for navy flounder
3568f96 (tag:
20210315) linux-firmware: Update firmware file for Intel Bluetooth AX210
9e96e50 linux-firmware: Update firmware file for Intel Bluetooth AX200
c8d0db5 linux-firmware: Update firmware file for Intel Bluetooth AX201
5e2a387 Merge tag 'iwlwifi-fw-2021-03-05-v3' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/linux-firmware into main
b0d3e31 rtw88: 8822c: Update normal firmware to v9.9.6
5a2fd63 iwlwifi: add new FWs from core59-66 release
4f54906 iwlwifi: update 9000-family firmwares
11b7607 iwlwifi: update 7265D firmware
e425f76 Merge branch 'add-silabs-wf200' of github.com:jerome-pouiller/linux-firmware into main
5ecd13f Mellanox: Add new mlxsw_spectrum firmware xx.2008.2406
58fb90a linux-firmware: add frimware for mediatek bluetooth chip (MT7921)
e576a1b rtw89: 8852a: add firmware v0.9.12.2
048a7cb WHENCE: add missing symlink for BananaPi M3
aa6c6e7 Add symlink for BananaPi M2 to brcmfmac43430-sdio config
58825f7 brcm: Fix Raspberry Pi 4B NVRAM file
520f71b silabs: add new firmware for WF200
f7915a0 amdgpu: add initial firmware for green sardine
80cb579 rtw88: RTL8822C: Update normal firmware to v9.9.5
b79d239 (tag:
20210208) Merge branch 'DG1-guc-huc-ADLS-dmc' of git://anongit.freedesktop.org/drm/drm-firmware into main
66970e1 Merge branch 'qcom-rb5' of https://github.com/lumag/linux-firmware into main
cf6fc2b Mellanox: Add new mlxsw_spectrum firmware xx.2008.2304
391fd50 linux-firmware: add firmware for MT7921
c5e3240 rtw88: RTL8821C: Update firmware to v24.8
d33d2d8 linux-firmware: Update firmware file for Intel Bluetooth AX210
3027ae4 linux-firmware: Update firmware file for Intel Bluetooth AX200
13979c3 linux-firmware: Update firmware file for Intel Bluetooth AX201
348d8a9 i915: Add DMC v2.01 for ADL-S
f33f1f7 i915: Add HuC v7.7.1 for DG1
6a422f5 i915: Add GuC v49.0.1 for DG1
df822a8 qcom: Add venus firmware files for VPU-1.0
11a1db1 qcom: Add SM8250 Compute DSP firmware
e55248b qcom: Add SM8250 Audio DSP firmware
da74cc6 qcom: add firmware files for Adreno a650
0578970 brcm: Link RPi4's WiFi firmware with DMI machine name.
d528862 brcm: Add NVRAM for Vamrs 96boards Rock960
870b805 brcm: Update Raspberry Pi 3B+/4B NVRAM for downstream changes
a28a590 cypress: Fix link direction
060ad8b cypress: Link the new cypress firmware to the old brcm files
0f0aefd brcm: remove old brcm firmwares that have newer cypress variants
f580dc2 rtl_bt: Update RTL8822C BT(UART I/F) FW to 0x059A_25CB
7df2220 rtl_bt: Update RTL8822C BT(USB I/F) FW to 0x099a_7253
e79405d rtl_bt: Add firmware and config files for RTL8852A BT USB chip
ef3813d rtl_bt: Update RTL8821C BT(USB I/F) FW to 0x829a_7644
646f159 (tag:
20201218) make AP6212 in bananpi m2 plus/zero work
28185ec linux-firmware: Update firmware file for Intel Bluetooth AX210
23da869 linux-firmware: Update firmware file for Intel Bluetooth AX200
2099248 linux-firmware: Update firmware file for Intel Bluetooth AX201
94de5e2 linux-firmware: Update firmware file for Intel Bluetooth 9560
27a3689 linux-firmware: Update firmware file for Intel Bluetooth 9260
5c3c4af Merge branch 'lt9611uxc' of https://github.com/lumag/linux-firmware into main
aaed4a8 Merge branch 'v1.1.6' of https://github.com/irui-wang/linux_fw_vpu_v1.1.6 into main
d8c9865 Merge branch 'master' of https://github.com/sampnimm/linux-firmware-BT into main
63ab3db linux-firmware: add firmware for Lontium LT9611UXC DSI to HDMI bridge
0fe0fe0 mediatek: update MT8173 VPU firmware to v1.1.6
1a08ec9 QCA : Updated firmware files for WCN3991
7455a36 Merge branch 'guc_v49' of git://anongit.freedesktop.org/drm/drm-firmware into main
7eb7fda linux-firmware: Update firmware file for Intel Bluetooth AX210
5cbf459 linux-firmware: Update firmware file for Intel Bluetooth AX210
c487f7d i915: Add GuC firmware v49.0.1 for all platforms
d9ffb07 i915: Remove duplicate KBL DMC entry
b362fd4 Mellanox: Add new mlxsw_spectrum firmware xx.2008.2018
bc9cd0b linux-firmware: Update AMD SEV firmware
54c797a amdgpu: add sienna cichlid firmware for 20.45
1340e9c amdgpu: update vega20 firmware for 20.45
b260c9c amdgpu: update vega12 firmware for 20.45
d683bd5 amdgpu: update vega10 firmware for 20.45
7c81cc2 amdgpu: update renoir firmware for 20.45
3619e57 amdgpu: update navi14 firmware for 20.45
68ce0fb amdgpu: update navi12 firmware for 20.45
e889b80 amdgpu: update navi10 firmware for 20.45
f4edc15 amdgpu: update raven2 firmware for 20.45
e71210f amdgpu: update raven firmware for 20.45
Signed-off-by: Tomas Lara <tl849670@gmail.com>
[rebased; removed brcmfmac changes due to removed firmware]
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Fri, 4 Jun 2021 13:12:14 +0000 (15:12 +0200)]
generic: backport at803x fixes
As patches for the AR8031/AR8033 copper page selection were merged
upstream, we can backport these patches.
This also fixes a PHY capabilities detection issue on the Ubiquiti
ER-X-SFP.
Signed-off-by: David Bauer <mail@david-bauer.net>
Robert Marko [Sun, 16 May 2021 16:01:28 +0000 (18:01 +0200)]
ethtool: update to version 5.12
Update ethtool to newly released 5.12 version.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Daniel Golle [Mon, 7 Jun 2021 22:13:18 +0000 (23:13 +0100)]
ugps: update to git HEAD
86ee86e nmea: parse $GPZDA sentences for date/time
8e12414 nmea: parse $GPGLL sentences for position
5e88403 ubus: display only available information
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Jonathan A. Kollasch [Fri, 11 Sep 2020 19:33:39 +0000 (14:33 -0500)]
ath79: fix eth0 PLL registers on WD My Net Wi-Fi Range Extender
This replaces the register bits for RGMII delay on the MAC side in favor
of having the RGMII delay on the PHY side by setting the phy-mode
property to rgmii-id (RGMII internal delay), which is supported by the
at803x driver. Speed 1000 is fixed as a result, so now all ethernet
speeds function.
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Reviewed-by: Michael Pratt <mcpratt@pm.me>
Nick Hainke [Sun, 25 Apr 2021 20:41:46 +0000 (22:41 +0200)]
ath79: Support for Ubiquiti Rocket 5AC Lite
The Ubiquiti Rocket 5AC Lite (R5AC-Lite) is an outdoor router.
Specifications:
- SoC: Qualcomm Atheros QCA9558
- RAM: 128 MB
- Flash: 16 MB SPI
- Ethernet: 1x 10/100/1000 Mbps
- WiFi 5 GHz: QCA988x
- Buttons: 1x (reset)
- LEDs: 1x power, 1x Ethernet, 4x RSSI
Installation:
- Instructions for XC-type Ubiquiti:
https://openwrt.org/toh/ubiquiti/common
Signed-off-by: Nick Hainke <vincent@systemli.org>
INAGAKI Hiroshi [Wed, 24 Mar 2021 15:19:59 +0000 (00:19 +0900)]
ath79: add support for NEC Aterm WF1200CR
NEC Aterm WF1200CR is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on
QCA9561.
Specification:
- SoC : Qualcomm Atheros QCA9561
- RAM : DDR2 128 MiB (W971GG6SB-25)
- Flash : SPI-NOR 8 MiB (MX25L6433FM2I-08G)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : QCA9561 (SoC)
- 5 GHz : QCA9888
- Ethernet : 2x 10/100 Mbps
- Switch : QCA9561 (SoC)
- LEDs/Keys : 8x/3x (2x buttons, 1x slide-switch)
- UART : through-hole on PCB
- JP1: Vcc, GND, NC, TX, RX from "JP1" marking
- 115200n8
- Power : 12 VDC, 0.9 A
Flash instruction using factory image (stock: < v1.3.2):
1. Boot WF1200CR normally with "Router" mode
2. Access to "http://192.168.10.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt factory image and click update ("更新") button to
perform firmware update
4. Wait ~150 seconds to complete flashing
Alternate flash instruction using initramfs image (stock: >= v1.3.2):
1. Prepare the TFTP server with the IP address 192.168.1.10 and place
the OpenWrt initramfs image to the TFTP directory with the name
"
0101A8C0.img"
2. Connect serial console to WF1200CR
3. Boot WF1200CR and interrupt with any key after the message
"Hit any key to stop autoboot: 2", the U-Boot starts telnetd after
the message "starting telnetd server from server 192.168.1.1"
4. login the telnet (address: 192.168.1.1)
5. Perform the following commands to modify "bootcmd" variable
temporary and check the value
(to ignore the limitation of available commands, "tp; " command at
the first is required as dummy, and the output of "printenv" is
printed on the serial console)
tp; set bootcmd 'set autostart yes; tftpboot'
tp; printenv
6. Save the modified variable with the following command and reset
device
tp; saveenv
tp; reset
7. The U-Boot downloads initramfs image from TFTP server and boots it
8. On initramfs image, download the sysupgrade image to the device and
perform the following commands to erase stock firmware and sysupgrade
mtd erase firmware
sysupgrade <sysupgrade image>
9. After the rebooting by completion of sysupgrade, start U-Boot telnetd
and login with the same way above (3, 4)
10. Perform the following commands to reset "bootcmd" variable to the
default and reset the device
tp; run seattle
tp; reset
(the contents of "seattle":
setenv bootcmd 'bootm 0x9f070040' && saveenv)
11. Wait booting-up the device
Known issues:
- the following 6x LEDs are connected to the gpio controller on QCA9888
chip and the implementation of control via the controller is missing in
ath10k/ath10k-ct
- "ACTIVE" (Red/Green)
- "2.4GHz" (Red/Green)
- "5GHz" (Red/Green)
Note:
- after the version v1.3.2 of stock firmware, "offline update" by
uploading image by user is deleted and the factory image cannot be
used
- the U-Boot on WF1200CR doesn't configure the port-side LEDs on WAN/LAN
and the configuration is required on OpenWrt
- gpio-hog: set the direction of GPIO 14(WAN)/19(LAN) to output
- pinmux: set GPIO 14/19 as switch-controlled LEDs
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Andreas Böhler [Sun, 14 Mar 2021 23:07:17 +0000 (00:07 +0100)]
ramips: Add support for SERCOMM NA502
The SERCOMM NA502 is a smart home gateway manufactured by SERCOMM and sold
under different brands (among others, A1 Telekom Austria SmartHome
Gateway). It has multi-protocol radio support in addition to LAN and WiFi.
Note: BLE is currently unsupported.
Specifications
--------------
- MT7621ST 880MHz, Single-Core, Dual-Thread
- MT7603EN 2.4GHz WiFi
- MT7662EN 5GHz WiFi + BLE
- 128MiB NAND
- 256MiB DDR3 RAM
- SD3503 ZWave Controller
- EM357 Zigbee Coordinator
MAC address assignment
----------------------
LAN MAC is read from the config partition, WiFi 2.4GHz is LAN+2 and matches
the OEM firmware. WiFi 5GHz with LAN+1 is an educated guess since the
OEM firmware does not enable 5GHz WiFi.
Installation
------------
Attach serial console, then boot the initramfs image via TFTP.
Once inside OpenWrt, run sysupgrade -n with the sysupgrade file.
Attention: The device has a dual-firmware design. We overwrite kernel2,
since kernel1 contains an automatic recovery image.
If you get NAND ECC errors and are stuck with bad eraseblocks, try to
erase the mtd partition first with
mtd unlock ubi
mtd erase ubi
This should only be needed once.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
[use kiB for IMAGE_SIZE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Sun, 6 Jun 2021 17:17:47 +0000 (19:17 +0200)]
treewide: do not quote compatible in shell scripts
The compatible is a literal string without any problematic
characters, so there is no reason to quote it.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Sun, 6 Jun 2021 17:06:29 +0000 (19:06 +0200)]
uboot-kirkwood: refresh patches
This is only cosmetic, but the next one adding a patch here would
have to do it anyway, and thus will get a smaller diff for review
now.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
BERENYI Balazs [Sat, 2 Jan 2021 18:49:42 +0000 (18:49 +0000)]
kirkwood: Add support for Sheevaplug
Globalscale SheevaPlug:
* Marvell Kirkwood
88F6281
* 512 MB SDRAM
* 512 MB Flash
* Gigabit Network
* USB 2.0
* SD slot
* Serial console
The device is supported in mainline uboot/linux the commit adds only
some openwrt config for building an image.
Installation:
1 - Update uboot:
setenv ipaddr '192.168.0.111'
setenv serverip '192.168.0.1'
tftpboot u-boot.kwb
nand erase 0x0 0x100000
nand write 0x800000 0x0 0x100000
reset
2 - Install OpenWRT:
setenv ethaddr 00:50:43:01:xx:xx
saveenv
setenv ipaddr '192.168.0.111'
setenv serverip '192.168.0.1'
tftpboot openwrt-kirkwood-globalscale_sheevaplug-squashfs-factory.bin
nand erase.part ubi
nand write 0x800000 ubi 0x600000
reset
Signed-off-by: BERENYI Balazs <balazs@wee.hu>
Reviewed-by: Pawel Dembicki <paweldembicki@gmail.com>
[add vendor name for uboot-kirkwood, merge patches, copy to 5.10,
add AUTORELEASE for uboot-kirkwood, refresh patches]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Ben Gainey [Sun, 31 Jan 2021 11:15:38 +0000 (11:15 +0000)]
ramips: add support for the Wavlink WL-WN579X3
About the device
----------------
SoC: MediaTek MT7620a @ 580MHz
RAM: 64M
FLASH: 8MB
WiFi: SoC-integrated: MediaTek MT7620a bgn
WiFi: MediaTek MT7612EN nac
GbE: 2x (RTL8211F)
BTN: - WPS
- Reset
- Router/Repeater/AP (3-way slide-switch)
LED: - WPS (blue)
- 3-segment Wifi signal representation (blue)
- WiFi (blue)
- WAN (blue)
- LAN (blue)
- Power (blue)
UART: UART is present as Pads with through-holes on the PCB. They are
located next to the reset button and are labelled Vcc/TX/RX/GND as
appropriate. Use 3.3V, 57600-8N1.
Installation
------------
Using the webcmd interface
--------------------------
Warning: Do not update to the latest Wavlink firmware (version
20201201) as this removes the webcmd console and you will need to
use the serial port instead.
You will need to have built uboot/sqauashfs image for this device,
and you will need to provide an HTTP service where the image can
be downloaded from that is accessible by the device.
You cannot use the device manufacturers firmware upgrade interface
as it rejects the OpenWrt image.
1. Log into the device's admin portal. This is necessary to
authenticate you as a user in order to be able to access the
webcmd interface.
2. Navigate to http://<device-ip>/webcmd.shtml - you can access
the console directly through this page, or you may wish to
launch the installed `telnetd` and use telnet instead.
* Using telnet is recommended since it provides a more
convenient shell interface that the web form.
* Launch telnetd from the form with the command `telnetd`.
* Check the port that telnetd is running on using
`netstat -antp|grep telnetd`, it is likely to be 2323.
* Connect to the target using `telnet`. The username should
be `admin2860`, and the password is your admin password.
3. On the target use `curl` to download the image.
e.g. `curl -L -O http://<some-other-lan-ip>/openwrt-ramips-mt7620-\
wavlink_wl-wn579x3-squashfs-sysupgrade.bin`.
Check the hash using `md5sum`.
4. Use the mtd_write command to flash the image.
* The flash partition should be mtd4, but check
/sys/class/mtd/mtd4/name first. The partition should be
called 'Kernel'.
* To flash use the following command:
`mtd_write -r -e /dev/mtd<n> write <image-file> /dev/mtd<n>`
Where mtd<n> is the Kernel partition, and <image-file> is
the OpenWrt image previously downloaded.
* The command above will erase, flash and then reboot the
device. Once it reboots it will be running OpenWrt.
Connect via ssh to the device at 192.168.1.1 on the LAN port.
The WAN port will be configured via DHCP.
Using the serial port
---------------------
The device uses uboot like many other MT7260a based boards. To
use this interface, you will need to connect to the serial
interface, and provide a TFTP server. At boot follow the
bootloader menu and select option 2 to erase/flash the image.
Provide the address and filename details for the tftp server.
The bootloader will do the rest.
Once the image is flashed, the board will boot into OpenWrt. The
console is available over the serial port.
Signed-off-by: Ben Gainey <ba.gainey@googlemail.com>
Felix Matouschek [Thu, 18 Feb 2021 22:12:01 +0000 (23:12 +0100)]
ath79: add support for Devolo dLAN pro 1200+ WiFi ac
This patch adds support for the Devolo dLAN pro 1200+ WiFi ac.
This device is a plc wifi AC2400 router/extender with 2 Ethernet ports,
has a QCA7500 PLC and uses the HomePlug AV2 standard.
Other than the PLC the hardware is identical to the Devolo Magic 2 WIFI.
Therefore it uses the same dts, which was moved to a dtsi to be included
by both boards.
This is a board that was previously included in the ar71xx tree.
Hardware:
SoC: AR9344
CPU: 560 MHz
Flash: 16 MiB (W25Q128JVSIQ)
RAM: 128 MiB DDR2
Ethernet: 2xLAN 10/100/1000
PLC: QCA75000 (Qualcomm HPAV2)
PLC Uplink: 1Gbps MIMO
PLC Link: RGMII 1Gbps (WAN)
WiFi: Atheros AR9340 2.4GHz 802.11bgn
Atheros AR9882-BR4A 5GHz 802.11ac
Switch: QCA8337, Port0:CPU, Port2:PLC, Port3:LAN1, Port4:LAN2
Button: 3x Buttons (Reset, wifi and plc)
LED: 3x Leds (wifi, plc white, plc red)
GPIO Switch: 11-PLC Pairing (Active Low)
13-PLC Enable
21-WLAN power
MACs Details verified with the stock firmware:
Radio1: 2.4 GHz &wmac *:4c Art location: 0x1002
Radio0: 5.0 GHz &pcie *:4d Art location: 0x5006
Ethernet ðernet *:4e = 2.4 GHz + 2
PLC uplink --- *:4f = 2.4 GHz + 3
Label MAC address is from PLC uplink
The Powerline (PLC) interface of the dLAN pro 1200+ WiFi ac requires 3rd
party firmware which is not available from standard OpenWrt package
feeds. There is a package feed on github which you must add to
OpenWrt buildroot so you can build a firmware image which supports the
plc interface.
See: https://github.com/0xFelix/dlan-openwrt (forked from Devolo and
added compatibility for OpenWrt 21.02)
Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.100
2. Download the sysupgrade image and rename it to uploadfile
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Allow 1-2 minutes for the first boot.
Signed-off-by: Felix Matouschek <felix@matouschek.org>
[add "plus" to compatible and device name]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Hauke Mehrtens [Sat, 5 Jun 2021 16:21:57 +0000 (18:21 +0200)]
mac80211: Update to backports-5.10.42
The removed patches were integrated upstream.
The brcmf_driver_work workqueue was removed in brcmfmac with kernel
5.10.42, the asynchronous call was covered to a synchronous call. There
is no need to wait any more.
This part was removed manually from this patch:
brcm/860-brcmfmac-register-wiphy-s-during-module_init.patch
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Felix Fietkau [Sun, 6 Jun 2021 08:40:05 +0000 (10:40 +0200)]
mt76: update to the latest version
Add mt7915e dependency on kmod-thermal
22b690334c0f mt76: mt7915: do not fail if the cooling device could not be registered
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Josef Schlehofer [Sat, 1 May 2021 06:51:12 +0000 (08:51 +0200)]
linux-firmware: update to version
20210315 and trim down broadcom FW
In there linux-firmware repository located in kernel, there were removed old
broadcom firmware [1] as they seem to be likely vulnerable to KrØØk vulnerability
(CVE-2019-15126), because Cypress released new versions and superseded
by it.
In OpenWrt, there is Makefile for cypress-firmware, which already provides
the same named packages like it was in linux-firmware. For example, cypress-firmware-43455-sdio
provides brcmfmac-firmware-43455-sdio [2].
Changelog between
2020118 and
20210315:
3568f96 (tag:
20210315) linux-firmware: Update firmware file for Intel Bluetooth AX210
9e96e50 linux-firmware: Update firmware file for Intel Bluetooth AX200
c8d0db5 linux-firmware: Update firmware file for Intel Bluetooth AX201
5e2a387 Merge tag 'iwlwifi-fw-2021-03-05-v3' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/linux-firmware into main
b0d3e31 rtw88: 8822c: Update normal firmware to v9.9.6
5a2fd63 iwlwifi: add new FWs from core59-66 release
4f54906 iwlwifi: update 9000-family firmwares
11b7607 iwlwifi: update 7265D firmware
e425f76 Merge branch 'add-silabs-wf200' of github.com:jerome-pouiller/linux-firmware into main
5ecd13f Mellanox: Add new mlxsw_spectrum firmware xx.2008.2406
58fb90a linux-firmware: add frimware for mediatek bluetooth chip (MT7921)
e576a1b rtw89: 8852a: add firmware v0.9.12.2
048a7cb WHENCE: add missing symlink for BananaPi M3
aa6c6e7 Add symlink for BananaPi M2 to brcmfmac43430-sdio config
58825f7 brcm: Fix Raspberry Pi 4B NVRAM file
520f71b silabs: add new firmware for WF200
f7915a0 amdgpu: add initial firmware for green sardine
80cb579 rtw88: RTL8822C: Update normal firmware to v9.9.5
b79d239 (tag:
20210208) Merge branch 'DG1-guc-huc-ADLS-dmc' of git://anongit.freedesktop.org/drm/drm-firmware into main
66970e1 Merge branch 'qcom-rb5' of https://github.com/lumag/linux-firmware into main
cf6fc2b Mellanox: Add new mlxsw_spectrum firmware xx.2008.2304
391fd50 linux-firmware: add firmware for MT7921
c5e3240 rtw88: RTL8821C: Update firmware to v24.8
d33d2d8 linux-firmware: Update firmware file for Intel Bluetooth AX210
3027ae4 linux-firmware: Update firmware file for Intel Bluetooth AX200
13979c3 linux-firmware: Update firmware file for Intel Bluetooth AX201
348d8a9 i915: Add DMC v2.01 for ADL-S
f33f1f7 i915: Add HuC v7.7.1 for DG1
6a422f5 i915: Add GuC v49.0.1 for DG1
df822a8 qcom: Add venus firmware files for VPU-1.0
11a1db1 qcom: Add SM8250 Compute DSP firmware
e55248b qcom: Add SM8250 Audio DSP firmware
da74cc6 qcom: add firmware files for Adreno a650
0578970 brcm: Link RPi4's WiFi firmware with DMI machine name.
d528862 brcm: Add NVRAM for Vamrs 96boards Rock960
870b805 brcm: Update Raspberry Pi 3B+/4B NVRAM for downstream changes
a28a590 cypress: Fix link direction
060ad8b cypress: Link the new cypress firmware to the old brcm files
0f0aefd brcm: remove old brcm firmwares that have newer cypress variants
f580dc2 rtl_bt: Update RTL8822C BT(UART I/F) FW to 0x059A_25CB
7df2220 rtl_bt: Update RTL8822C BT(USB I/F) FW to 0x099a_7253
e79405d rtl_bt: Add firmware and config files for RTL8852A BT USB chip
ef3813d rtl_bt: Update RTL8821C BT(USB I/F) FW to 0x829a_7644
646f159 (tag:
20201218) make AP6212 in bananpi m2 plus/zero work
28185ec linux-firmware: Update firmware file for Intel Bluetooth AX210
23da869 linux-firmware: Update firmware file for Intel Bluetooth AX200
2099248 linux-firmware: Update firmware file for Intel Bluetooth AX201
94de5e2 linux-firmware: Update firmware file for Intel Bluetooth 9560
27a3689 linux-firmware: Update firmware file for Intel Bluetooth 9260
5c3c4af Merge branch 'lt9611uxc' of https://github.com/lumag/linux-firmware into main
aaed4a8 Merge branch 'v1.1.6' of https://github.com/irui-wang/linux_fw_vpu_v1.1.6 into main
d8c9865 Merge branch 'master' of https://github.com/sampnimm/linux-firmware-BT into main
63ab3db linux-firmware: add firmware for Lontium LT9611UXC DSI to HDMI bridge
0fe0fe0 mediatek: update MT8173 VPU firmware to v1.1.6
1a08ec9 QCA : Updated firmware files for WCN3991
7455a36 Merge branch 'guc_v49' of git://anongit.freedesktop.org/drm/drm-firmware into main
7eb7fda linux-firmware: Update firmware file for Intel Bluetooth AX210
5cbf459 linux-firmware: Update firmware file for Intel Bluetooth AX210
c487f7d i915: Add GuC firmware v49.0.1 for all platforms
d9ffb07 i915: Remove duplicate KBL DMC entry
b362fd4 Mellanox: Add new mlxsw_spectrum firmware xx.2008.2018
bc9cd0b linux-firmware: Update AMD SEV firmware
54c797a amdgpu: add sienna cichlid firmware for 20.45
1340e9c amdgpu: update vega20 firmware for 20.45
b260c9c amdgpu: update vega12 firmware for 20.45
d683bd5 amdgpu: update vega10 firmware for 20.45
7c81cc2 amdgpu: update renoir firmware for 20.45
3619e57 amdgpu: update navi14 firmware for 20.45
68ce0fb amdgpu: update navi12 firmware for 20.45
e889b80 amdgpu: update navi10 firmware for 20.45
f4edc15 amdgpu: update raven2 firmware for 20.45
e71210f amdgpu: update raven firmware for 20.45
[1] https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git/commit/?id=
0f0aefd733f70beae4c0246edbd2c158d5ce974c
[2] https://github.com/openwrt/openwrt/blob/
eeda8652f1655d4f9c11e9c9f51ddcd3377d119a/package/firmware/cypress-firmware/Makefile#L124
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Tomasz Maciej Nowak [Mon, 24 May 2021 12:41:15 +0000 (14:41 +0200)]
x86: add Roqos Core RC10 ethernet interfaces
eth0 -> single NIC (i211at)
eth1 -> single NIC (i211at) -> 4-port unmanaged switch (BCM53125U)
Notes
UART is exposed on J4 connector, pinout starting from pin marked 1:
1. GND, 2. NC?, 3. NC?, 4. RX, 5. TX, 6. NC?
baud: 115200, parity: none, flow control: none
The board is setup by coreboot with UEFI. To enter setup screen hold
ESC key on boot.
The 5-LED multicolor matrix is attached on first I2C device named
"Synopsys DesignWare I2C adapter" at address 0x60. Controlling values
are stored in /opt/roqos/etc/rcLED.conf of original firmware.
Remember to backup the original firmware, there are no downloadable
copies.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tomasz Maciej Nowak [Mon, 24 May 2021 12:41:14 +0000 (14:41 +0200)]
kernel: package Synopsys Designware PCI to I2C controller
This is present on Roqos Core RC10 and needed to control LED matrix.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tomasz Maciej Nowak [Tue, 25 May 2021 12:53:43 +0000 (14:53 +0200)]
mvebu: armada-37xx: remove ethernet alias patch
This patch has been added with initial support for ESPRESSObin board and
mistakenly it affects all boards with this SoC. Drop this patch since
the aliases are now in upstream dts for ESPRESSObin. If any boards are
relying on this, please add the respective alias to that board dts.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tomasz Maciej Nowak [Tue, 25 May 2021 13:26:06 +0000 (15:26 +0200)]
ipq40xx: add uboot-envtools to default packages
When support for Luma WRTQ-329ACN was added, the instructions for
flashing this device include using tools from uboot-envtools package.
Unfortunately the OpenWrt buildroot system omits packages from
DEVICE_PACKAGES when CONFIG_TARGET_MULTI_PROFILE,
CONFIG_TARGET_PER_DEVICE_ROOTFS, CONFIG_TARGET_ALL_PROFILES are set. In
result the official images are without tools mentioned in the
instruction. The workoround for the fashing would be installing
uboot-envtools when booted with initramfs image, but not always the
access to internet is available. The other method would be to issue the
necesary command in U-Boot environment but some serial terminals default
configuration don't work well with pasting lines longer than 80 chars.
Therefore add uboot-envtools to default packages, which adds really
small flash footprint to rootfs, where increased size usually is not an
issue.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Rui Salvaterra [Thu, 27 May 2021 10:56:37 +0000 (11:56 +0100)]
tools/isl: bump to 0.24
Tested with Graphite and -floop-nest-optimize, without issues.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Hauke Mehrtens [Fri, 28 May 2021 16:35:40 +0000 (18:35 +0200)]
toolchain: gdb: Add optional python support
Compile gdb with python support optionally.
To use the Python support in gdb some extra python files are needed,
install them too. While at it also install other shared files which we
did not install before.
If gdb is built without Python support the python folder does not
exists.
Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
Alex Henrie [Fri, 4 Jun 2021 04:37:49 +0000 (22:37 -0600)]
ipq806x: fix LAN and WAN port assignments on TP-Link AD7200
LAN port 4 was swapped with the WAN port and the remaining three LAN
ports were numbered in reverse order from their labels on the case.
Fixes: 1a775a4fd033 ("ipq806x: add support for TP-Link Talon AD7200")
Signed-off-by: Alex Henrie <alexhenrie24@gmail.com>
Martin Schiller [Wed, 19 May 2021 10:33:26 +0000 (12:33 +0200)]
layerscape: armv8_64b: enable CONFIG_ARM_PSCI_CPUIDLE
Enable PSCI firmware based CPUidle driver.
PSCI firmware is the standard power management control for all ARM64
based platforms.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Kuan-Yi Li [Sat, 29 May 2021 23:35:38 +0000 (07:35 +0800)]
kernel: usb: add kmod-usb-gadget-ncm
Add kernel module package for USB Network Control Model (NCM) Gadget
support.
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
Mark Carroll [Sat, 8 May 2021 11:42:50 +0000 (11:42 +0000)]
x86: kernel: enable Fusion-MPT SAS driver
Compile in MPT SAS driver required to mount rootfs on some VMWare
systems (e.g. required for 1&1 IONOS).
Signed-off-by: Mark Carroll <git@markcarroll.net>
Michael Yartys [Thu, 3 Jun 2021 21:50:12 +0000 (23:50 +0200)]
ath10k-ct: update to latest version
Changelog:
- ath10k-ct: Add security fixes.
- ath10k-ct: Add 5.12 kernel version.
- ath10k-ct: Fix the beacon/mcast/bcast override issue
- ath10k-ct 5.7: Fix setting mcast/bcast/beacon rate from debugfs.
- ath10k-ct: Add 5.11 driver.
Delete upstreamed patch and refresh the rest. Also, use the opportunity to
set PKG_RELEASE to $(AUTORELEASE).
Runtime-tested on ipq806x (Netgear R7800).
Signed-off-by: Michael Yartys <michael.yartys@protonmail.com>
John Audia [Thu, 3 Jun 2021 18:46:59 +0000 (14:46 -0400)]
kernel: bump 5.4 to 5.4.124
Manually rebased:
generic/hack-5.4/662-remove_pfifo_fast.patch
All other patches automatically rebased.
Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
[manual changes to ramips/patches-5.10/835-asoc-add-mt7620-support.patch]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rui Salvaterra [Thu, 3 Jun 2021 10:12:02 +0000 (11:12 +0100)]
kernel: bump 5.10 to 5.10.42
Deleted (reverse-appliable):
generic/pending-5.10/110-perf-jevents-fix-getting-maximum-number-of-fds.patch
Manually refreshed:
ramips/patches-5.10/835-asoc-add-mt7620-support.patch
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Adrian Schmutzler [Sat, 5 Jun 2021 21:54:37 +0000 (23:54 +0200)]
treewide: remove "+" sign for increment with macaddr_add
Many people appear to use an unneeded "+" prefix for the increment
when calculating a MAC address with macaddr_add. Since this is not
required and used inconsistently [*], just remove it.
[*] As a funny side-fact, copy-pasting has led to almost all
hotplug.d files using the "+", while nearly all of the
02_network files are not using it.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Shiji Yang [Sun, 16 May 2021 13:21:09 +0000 (21:21 +0800)]
ramips: split Youku YK1 to YK-L1 and YK-L1c
Device specifications:
* Model: Youku YK-L1/L1c
* CPU: MT7620A
* RAM: 128 MiB
* Flash: 32 MiB (YK-L1)/ 16 MiB (YK-L1c)
* LAN: 2* 10M/100M Ports
* WAN: 1* 10M/100M Port
* USB: 1* USB2.0
* SD: 1* MicroSD socket
* UART: 1* TTL, Baudrate 57600
Descriptions:
Previous supported device YOUKU yk1 is actually Youku YK-L1. Though they look
really different, the only hardware difference between the two models is flash
size, YK-L1 has 32 MiB flash but YK-L1c has 16MiB. It seems that YK-L1c can
compatible with YK-L1's firmware but it's better to split it to different models.
It is easy to identify the models by looking at the label on the bottom of the
device. The label has the model number "YK-L1" or "YK-L1c". Due to different flash
sizes, YK-L1c that using previous YK-L1's firmware needs to apply "force update"
to install compatible firmware, so please backup config file before system upgrade.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[use more specific name for DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Daniele Castro [Tue, 11 May 2021 12:17:50 +0000 (13:17 +0100)]
bcm63xx: drop USB LEDs for Technicolor TG582N / ADB P.DG A4001N
Remove the USB status red and green LEDs for
- ADB P.DG A4001N A-000-1A1-AX
- Technicolor TG582N
- Technicolor TG582N Telecom Italia
After having mounted an SMD socket for the flash memory for
JTAG reverse engineering, and so be able to easly swap between
OpenWrt and the stock FW, it turned out that the stock FW does
not light up the red and green USB LEDs exactly as I remembered.
Signed-off-by: Daniele Castro <danielecastro@hotmail.it>
[improve commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Michael Pratt [Wed, 5 May 2021 03:32:00 +0000 (23:32 -0400)]
ath79: use dynamic partitioning for TP-Link CPE series
CPExxx and WBSxxx boards with AR9344 SOC
use the OKLI lzma kernel loader
with the offset of 3 blocks of length 4k (0x3000)
in order to have a fake "kernel" that cannot grow larger
than how it is defined in the now static OEM partition table.
Before recent changes to the mtdsplit driver,
the uImage parser for OKLI only supported images
that started exactly on an eraseblock boundary.
The mtdsplit parser for uImage now supports identifying images
with any magic number value
and at any offset from the eraseblock boundary
using DTS properties to define those values.
So, it is no longer necessary to use fixed sizes
for kernel and rootfs
Tested-by: Andrew Cameron <apcameron@softhome.net> [CPE510 v2]
Tested-by: Bernhard Geier <freifunk@geierb.de> [WBS210 v2]
Tested-by: Petrov <d7c48mWsPKx67w2@gmail.com> [CPE210 v1]
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Adrian Schmutzler [Sat, 5 Jun 2021 15:59:39 +0000 (17:59 +0200)]
umbim: fix return value of proto_mbim_setup()
The variable name appears to be mistyped.
Suggested-by: Howard Chu <hyc@symas.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Sat, 5 Jun 2021 15:47:56 +0000 (17:47 +0200)]
umbim: fix whitespace issues
Make leading whitespaces consistent and remove trailing one.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Lauro Moreno [Wed, 28 Oct 2020 20:59:47 +0000 (14:59 -0600)]
ipq806x: add support for Askey RT4230W REV6
This adds support for the Askey RT4230W REV6
(Branded by Spectrum/Charter as RAC2V1K)
At this time, there's no way to reinstall the stock firmware so don't install
this on a router that's being rented.
Specifications:
Qualcomm IPQ8065
1 GB of RAM (DDR3)
512 MB Flash (NAND)
2x Wave 2 WiFi cards (QCA9984)
5x 10/100/1000 Mbps Ethernet (Switch: QCA8337)
1x LED (Controlled by a microcontroller that switches it between red and
blue with different patterns)
1x USB 3.0 Type-A
12V DC Power Input
UART header on PCB - pinout from top to bottom is RX, TX, GND, 5V
Port settings are 115200n8
More information: https://forum.openwrt.org/t/askey-rac2v1k-support/15830
https://deviwiki.com/wiki/Askey_RAC2V1K
To check what revision your router is, restore one of these config backups
through the stock firmware to get ssh access then run
"cat /proc/device-tree/model".
https://forum.openwrt.org/t/askey-rac2v1k-support/15830/17
The revision number on the board doesn't seem to be very consistent so that's
why this is needed. You can also run printenv in the uboot console and if
machid is set to 177d, that means your router is rev6.
Note: Don't install this if the router is being rented from an ISP. The defined
partition layout is different from the OEM one and even if you changed the
layout to match, backing up and restoring the OEM firmware breaks /overlay so
nothing will save and the router will likely enter a bootloop.
How to install:
Method 1: Install without opening the case using SSH and tftp
You'll need:
RAC2V1K-SSH.zip:
https://github.com/lmore377/openwrt-rt4230w/blob/master/RAC2V1K-SSH.zip
initramfs and sysupgrade images
Connect to one of the router's LAN ports
Download the RAC2V1K-SSH.zip file and restore the config file that
corresponds to your router's firmware (If you're firmware is newer than what's
in the zip file, just restore the 1.1.16 file)
After a reboot, you should be able to ssh into the router with username:
"4230w" and password: "linuxbox" or "admin". Run the following commannds
fw_setenv ipaddr 10.42.0.10 #IP of router, can be anything as long as
it's in the same subnet as the server
fw_setenv serverip 10.42.0.1# #IP of tftp server that's set up in next
steps
fw_setenv bootdelay 8
fw_setenv bootcmd "tftpboot initramfs.bin; bootm; bootipq"
Don't reboot the router yet.
Install and set up a tftp server on your computer
Set a static ip on the ethernet interface of your computer (use this for
serverip in the above commands)
Rename the initramfs image to initramfs.bin, and host it with the tftp
server
Reboot the router. If you set up everything right, the router led should
switch over to a slow blue glow which means openwrt is booted. If for some
reason the file doesn't get loaded into ram properly, it should still boot to
the OEM firmware.
After openwrt boots, ssh into it and run these commands:
fw_setenv bootcmd "setenv mtdids nand0=nand0 && setenv mtdparts
mtdparts=nand0:0x1A000000@0x2400000(firmware) && ubi part firmware && ubi
read 0x44000000 kernel 0x6e0000 && bootm"
fw_setenv bootdelay 2
After openwrt boots up, figure out a way to get the sysupgrade file onto it
(scp, custom build with usb kernel module included, wget, etc.) then flash it
with sysupgrade. After it finishes flashing, it should reboot, the light should
start flashing blue, then when the light starts "breathing" blue that means
openwrt is booted.
Method 2: Install with serial access (Do this if something fails and you can't
boot after using method 1)
You'll need:
initramfs and sysupgrade images
Serial access:
https://openwrt.org/inbox/toh/askey/askey_rt4230w_rev6#opening_the_case
Install and set up a tftp server
Set a static ip on the ethernet interface of your computer
Download the initramfs image, rename it to initramfs.bin, and host it with
the tftp server
Connect the wan port of the router to your computer
Interrupt U-Boot and run these commands:
setenv serverip 10.42.0.1 (You can use whatever ip you set for the computer)
setenv ipaddr 10.42.0.10 (Can be any ip as long as it's in the same subnet)
setenv bootcmd "setenv mtdids nand0=nand0 &&
set mtdparts mtdparts=nand0:0x1A000000@0x2400000(firmware) && ubi part firmware
&& ubi read 0x44000000 kernel 0x6e0000 && bootm"
saveenv
tftpboot initramfs.bin
bootm
After openwrt boots up, figure out a way to get the sysupgrade file onto it
(scp, custom build with usb kernel module included, wget, etc.) then flash it
with sysupgrade. After it finishes flashing, it should reboot, the light should
start flashing blue, then when the light starts "breathing" blue that means
openwrt is booted.
Signed-off-by: Lauro Moreno <lmore377@gmail.com>
[add entry in 5.10 patch, fix whitespace issues]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tee Hao Wei [Mon, 17 May 2021 19:46:36 +0000 (03:46 +0800)]
ramips: add support for Linksys EA8100 v1
Specifications:
- SoC: MT7621AT
- RAM: 256MB
- Flash: 128MB NAND
- Ethernet: 5 Gigabit ports
- WiFi: 2.4G/5G MT7615N
- USB: 1 USB 3.0, 1 USB 2.0
This device is very similar to the EA7300 v1/v2 and EA7500 v2.
Installation:
Upload the generated factory image through the factory web interface.
(following part taken from EA7300 v2 commit message:)
This might fail due to the A/B nature of this device. When flashing, OEM
firmware writes over the non-booted partition. If booted from 'A',
flashing over 'B' won't work. To get around this, you should flash the
OEM image over itself. This will then boot the router from 'B' and
allow you to flash OpenWRT without problems.
Reverting to factory firmware:
Hard-reset the router three times to force it to boot from 'B.' This is
where the stock firmware resides. To remove any traces of OpenWRT from
your router simply flash the OEM image at this point.
With thanks to Leon Poon (@LeonPoon) for the initial bringup.
Signed-off-by: Tee Hao Wei <angelsl@in04.sg>
[add missing entry in 10_fix_wifi_mac]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Jonathan Sturges [Sat, 5 Jun 2021 12:17:42 +0000 (08:17 -0400)]
ramips: add support for Amped Wireless ALLY router and extender
Amped Wireless ALLY is a whole-home WiFi kit, with a router (model
ALLY-R1900K) and an Extender (model ALLY-00X19K). Both are devices are
11ac and based on MediaTek MT7621AT and MT7615N chips. The units are
nearly identical, except the Extender lacks a USB port and has a single
Ethernet port.
Specification:
- SoC: MediaTek MT7621AT (2C/4T) @ 880MHz
- RAM: 128MB DDR3 (Nanya NT5CC64M16GP-DI)
- FLASH: 128MB NAND (Winbond W29N01GVSIAA)
- WiFi: 2.4/5 GHz 4T4R
- 2.4GHz MediaTek MT7615N bgn
- 5GHz MediaTek MT7615N nac
- Switch: SoC integrated Gigabit Switch
- USB: 1x USB3 (Router only)
- BTN: Reset, WPS
- LED: single RGB
- UART: through-hole on PCB.
J1: pin1 (square pad, towards rear)=3.3V, pin2=RX,
pin3=GND, pin4=TX. Settings: 57600/8N1.
Note regarding dual system partitions
-------------------------------------
The vendor firmware and boot loader use a dual partition scheme. The boot
partition is decided by the bootImage U-boot environment variable: 0 for
the 1st partition, 1 for the 2nd.
OpenWrt does not support this scheme and will always use the first OS
partition. It will set bootImage to 0 during installation, making sure
the first partition is selected by the boot loader.
Also, because we can't be sure which partition is active to begin with, a
2-step flash process is used. We first flash an initramfs image, then
follow with a regular sysupgrade.
Installation:
Router (ALLY-R1900K)
1) Install the flashable initramfs image via the OEM web-interface.
(Alternatively, you can use the TFTP recovery method below.)
You can use WiFi or Ethernet.
The direct URL is: http://192.168.3.1/07_06_00_firmware.html
a. No login is needed, and you'll be in their setup wizard.
b. You might get a warning about not being connected to the Internet.
c. Towards the bottom of the page will be a section entitled "Or
Manually Upgrade Firmware from a File:" where you can manually choose
and upload a firmware file.
d: Click "Choose File", select the OpenWRT "initramfs" image and click
"Upload."
2) The Router will flash the OpenWrt initramfs image and reboot. After
booting, LuCI will be available on 192.168.1.1.
3) Log into LuCI as root; there is no password.
4) Optional (but recommended) is to backup the OEM firmware before
continuing; see process below.
5) Complete the Installation by flashing a full OpenWRT image. Note:
you may use the sysupgrade command line tool in lieu of the UI if
you prefer.
a. Choose System -> Backup/Flash Firmware.
b. Click "Flash Image..." under "Flash new firmware image"
c. Click "Browse..." and then select the sysupgrade file.
d. Click Upload to upload the sysupgrade file.
e. Important: uncheck "Keep settings and retain the current
configuration" for this initial installation.
f. Click "Continue" to flash the firmware.
g. The device will reboot and OpenWRT is installed.
Extender (ALLY-00X19K)
1) This device requires a TFTP recovery procedure to do an initial load
of OpenWRT. Start by configuring a computer as a TFTP client:
a. Install a TFTP client (server not necessary)
b. Configure an Ethernet interface to 192.168.1.x/24; don't use .1 or .6
c. Connect the Ethernet to the sole Ethernet port on the X19K.
2) Put the ALLY Extender in TFTP recovery mode.
a. Do this by pressing and holding the reset button on the bottom while
connecting the power.
b. As soon as the LED lights up green (roughly 2-3 seconds), release
the button.
3) Start the TFTP transfer of the Initramfs image from your setup machine.
For example, from Linux:
tftp -v -m binary 192.168.1.6 69 -c put initramfs.bin
4) The Extender will flash the OpenWrt initramfs image and reboot. After
booting, LuCI will be available on 192.168.1.1.
5) Log into LuCI as root; there is no password.
6) Optional (but recommended) is to backup the OEM firmware before
continuing; see process below.
7) Complete the Installation by flashing a full OpenWRT image. Note: you
may use the sysupgrade command line tool in lieu of the UI if you prefer.
a. Choose System -> Backup/Flash Firmware.
b. Click "Flash Image..." under "Flash new firmware image"
c. Click "Browse..." and then select the sysupgrade file.
d. Click Upload to upload the sysupgrade file.
e. Important: uncheck "Keep settings and retain the current
configuration" for this initial installation.
f. Click "Continue" to flash the firmware.
g. The device will reboot and OpenWRT is installed.
Backup the OEM Firmware:
-----------------------
There isn't any downloadable firmware for the ALLY devices on the Amped
Wireless web site. Reverting back to the OEM firmware is not possible
unless we have a backup of the original OEM firmware.
The OEM firmware may be stored on either /dev/mtd3 ("firmware") or
/dev/mtd6 ("oem"). We can't be sure which was overwritten with the
initramfs image, so backup both partitions to be safe.
1) Once logged into LuCI, navigate to System -> Backup/Flash Firmware.
2) Under "Save mtdblock contents," first select "firmware" and click
"Save mtdblock" to download the image.
3) Repeat the process, but select "oem" from the pull-down menu.
Revert to the OEM Firmware:
--------------------------
* U-boot TFTP:
Follow the TFTP recovery steps for the Extender, and use the
backup image.
* OpenWrt "Flash Firmware" interface:
Upload the backup image and select "Force update"
before continuing.
Signed-off-by: Jonathan Sturges <jsturges@redhat.com>
Aashish Kulkarni [Tue, 2 Mar 2021 05:10:14 +0000 (10:40 +0530)]
ramips: add support for Linksys E5600
This submission relied heavily on the work of Linksys EA7300 v1/ v2.
Specifications:
* SoC: MediaTek MT7621A (880 MHz 2c/4t)
* RAM: 128M DDR3-1600
* Flash: 128M NAND
* Eth: MediaTek MT7621A (10/100/1000 Mbps x5)
* Radio: MT7603E/MT7613BE (2.4 GHz & 5 GHz)
* Antennae: 2 internal fixed in the casing and 2 on the PCB
* LEDs: Blue (x4 Ethernet)
Blue+Orange (x2 Power + WPS and Internet)
* Buttons: Reset (x1)
WPS (x1)
Installation:
Flash factory image through GUI.
This device has 2 partitions for the firmware called firmware and
alt_firmware. To successfully flash and boot the device, the device
should have been running from alt_firmware partition. To get the device
booted through alt_firmware partition, download the OEM firmware from
Linksys website and upgrade the firmware from web GUI. Once this is done,
flash the OpenWrt Factory firmware from web GUI.
Reverting to factory firmware:
1. Boot to 'alt_firmware'(where stock firmware resides) by doing one of
the following:
Press the "wps" button as soon as power LED turns on when booting.
(OR) Hard-reset the router consecutively three times to force it to
boot from 'alt_firmware'.
2. To remove any traces of OpenWRT from your router simply flash the OEM
image at this point.
Signed-off-by: Aashish Kulkarni <aashishkul@gmail.com>
[fix hanging indents and wrap to 74 characters per line,
add kmod-mt7663-firmware-sta package for 5GHz STA mode to work,
remove sysupgrade.bin and concatenate IMAGES instead in mt7621.mk,
set default-state "on" for power LED]
Signed-off-by: Sannihith Kinnera <digislayer@protonmail.com>
[move check-size before append-metadata, remove trailing whitespace]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Robert Marko [Wed, 25 Nov 2020 13:23:58 +0000 (14:23 +0100)]
ipq40xx: add netgear wac510 support
This adds support for the Netgear WAC510 Insight Managed Smart Cloud
Wireless Access Point, an indoor dual-band, dual-radio 802.11ac
business-class wireless AP with integrated omnidirectional antennae
and two 10/100/1000 Mbps Ethernet ports.
For more information see:
<https://www.netgear.com/business/wifi/access-points/wac510>
Specifications:
SoC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 256 MiB
Flash1: 2 MiB Winbond W25Q16JV SPI-NOR
Flash2: 128 MiB Winbond W25N01GVZEIG SPI-NAND
Ethernet: Built-in IPQ4018 (SoC, QCA8072 PHY), 2x 1000/100/10 port,
WAN port active IEEE 802.3af/at PoE in
Wireless1: Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 3 dBi antennae
Wireless2: Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 4 dBi antennae
Input: (Optional) Barrel 12 V 2.5 A Power, Reset button SW1
LEDs: Power, Insight, WAN PoE, LAN, 2.4G WLAN, 5G WLAN
Serial: Header J2
1 - 3.3 Volt (Do NOT connect!)
2 - TX
3 - RX
4 - Ground
WARNING: The serial port needs a TTL/RS-232 3.3 volt level converter!
The Serial settings are 115200-8-N-1.
Installation via Stock Web Interface:
BTW: The default factory console/web interface login user/password are
admin/password.
In the web interface navigating to Management - Maintenance - Upgrade -
'Firmware Upgrade' will show you what is currently installed e.g.:
Manage Firmware
Current Firmware Version: V5.0.10.2
Backup Firmware Version: V1.2.5.11
Under 'Upgrade Options' choose Local (alternatively SFTP would be
available) then click/select 'Browse File' on the right side, choose
openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.tar
and hit the Upgrade button below. After a minute or two your browser
should indicate completion printing 'Firmware update complete.' and
'Rebooting AP...'.
Note that OpenWrt will use the WAN PoE port as actual WAN port
defaulting to DHCP client but NOT allowing LuCI access, use LAN port
defaulting to 192.168.1.1/24 to access LuCI.
Installation via TFTP Requiring Serial U-Boot Access:
Connect to the device's serial port and hit any key to stop autoboot.
Upload and boot the initramfs based OpenWrt image as follows:
(IPQ40xx) # setenv serverip 192.168.1.1
(IPQ40xx) # setenv ipaddr 192.168.1.2
(IPQ40xx) # tftpboot openwrt-ipq40xx-generic-netgear_wac510-initramfs-fit-uImage.itb
(IPQ40xx) # bootm
Note: This only runs OpenWrt from RAM and has not installed anything
to flash as of yet. One may permanently install OpenWrt as follows:
Check the MTD device number of the active partition:
root@OpenWrt:/# dmesg | grep 'set to be root filesystem'
[ 1.010084] mtd: device 9 (rootfs) set to be root filesystem
Upload the factory image ending with .ubi to /tmp (e.g. using scp or
tftp). Then flash the image as follows (substituting the 9 in mtd9
below with whatever number reported above):
root@OpenWrt:/# ubiformat /dev/mtd9 -f /tmp/openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.ubi
And reboot.
Dual Image Configuration:
The default U-Boot boot command bootipq uses the U-Boot environment
variables primary/secondary to decide which image to boot. E.g.
primary=0, secondary=
3800000 uses rootfs while primary=
3800000,
secondary=0 uses rootfs_1.
Switching their values changes the active partition. E.g. from within
U-Boot:
(IPQ40xx) # setenv primary 0
(IPQ40xx) # setenv secondary
3800000
(IPQ40xx) # saveenv
Or from a OpenWrt userspace serial/SSH console:
fw_setenv primary 0
fw_setenv secondary
3800000
Note that if you install two copies of OpenWrt then each will have its
independent configuration not like when switching partitions on the
stock firmware.
BTW: The kernel log shows which boot partition is active:
[ 2.439050] ubi0: attached mtd9 (name "rootfs", size 56 MiB)
vs.
[ 2.978785] ubi0: attached mtd10 (name "rootfs_1", size 56 MiB)
Note: After 3 failed boot attempts it automatically switches partition.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[squashed netgear-tar commit into main and rename netgear-tar for
now, until it is made generic.]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Felix Fietkau [Fri, 4 Jun 2021 07:12:07 +0000 (09:12 +0200)]
hostapd: configure inter-AP communication interface for 802.11r
In setups using VLAN bridge filtering, hostapd may need to communicate using
a VLAN interface on top of the bridge, instead of using the bridge directly
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Philipp Borgers [Wed, 2 Jun 2021 09:01:32 +0000 (11:01 +0200)]
ramips: enable additional UART on MikroTik RouterBOARD M33G
The RouterBOARD M33G has an additional UART that should be enabled
by default.
Signed-off-by: Philipp Borgers <borgers@mi.fu-berlin.de>
Zoltan HERPAI [Mon, 3 Aug 2020 21:07:21 +0000 (23:07 +0200)]
ath79: add support for Qualcomm AP143 reference boards
Specifications:
SoC: QCA9533
DRAM: 32Mb DDR1
Flash: 8/16Mb SPI-NOR
LAN: 4x 10/100Mbps via AR8229 switch (integrated into SoC)
on GMII
WAN: 1x 10/100Mbps via MII
WLAN: QCA9530
USB: 1x 2.0
UART: standard QCA UART header
JTAG: yes
Button: 1x WPS, 1x reset
LEDs: 8x LEDs
A version with 4Mb flash is also available, but due to lack of
enough space it's not supported.
As the original flash layout does not provide enough space for
the kernel (1472k), the firmware uses OKLI and concat flash to
overcome the limitation without changing the boot address of the
bootloaders.
Installation:
1. Original bootloader
Connect the board to ethernet
Set up a server with an IP address of 192.168.1.10
Make the openwrt-ath79-generic-qca_ap143-8m-squashfs-factory.bin
available via TFTP
tftpboot 0x80060000 openwrt-ath79-generic-qca_ap143-8m-squashfs-factory.bin
erase 0x9f050000 +$filesize
cp.b $fileaddr 0x9f050000 $filesize
Reboot the board.
2. pepe2k's u-boot_mod
Connect the board to ethernet
Set up a server with an IP address of 192.168.1.10
Make the openwrt-ath79-generic-qca_ap143-8m-squashfs-factory.bin
available via TFTP, as "firmware.bin"
run fw_upg
Reboot the board.
For the 16M version of the board, please use
openwrt-ath79-generic-qca_ap143-16m-squashfs-factory.bin
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
[use fwconcatX names, drop redundant uart status, fix IMAGE_SIZE,
set up IMAGE/factory.bin without metadata]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sven Eckelmann [Mon, 23 Nov 2020 12:41:34 +0000 (13:41 +0100)]
ath79: Add support for OpenMesh A40
Device specifications:
======================
* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi (11n)
* 2T2R 5 GHz Wi-Fi (11ac)
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x ethernet
- eth0
+ Label: Ethernet 1
+ AR8035 ethernet PHY (RGMII)
+ 10/100/1000 Mbps Ethernet
+ 802.3af POE
+ used as WAN interface
- eth1
+ Label: Ethernet 2
+ AR8035 ethernet PHY (SGMII)
+ 10/100/1000 Mbps Ethernet
+ used as LAN interface
* 1x USB
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot
0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Sven Eckelmann [Mon, 23 Nov 2020 12:41:34 +0000 (13:41 +0100)]
ath79: Add support for OpenMesh A60
Device specifications:
======================
* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 3T3R 2.4 GHz Wi-Fi (11n)
* 3T3R 5 GHz Wi-Fi (11ac)
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x ethernet
- eth0
+ Label: Ethernet 1
+ AR8035 ethernet PHY (RGMII)
+ 10/100/1000 Mbps Ethernet
+ 802.3af POE
+ used as WAN interface
- eth1
+ Label: Ethernet 2
+ AR8031 ethernet PHY (SGMII)
+ 10/100/1000 Mbps Ethernet
+ used as LAN interface
* 1x USB
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot
0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Ansuel Smith [Tue, 1 Jun 2021 23:49:50 +0000 (01:49 +0200)]
mac80211: split ath patch in dedicated subdir
The ath patch number is already large and adding other patch for ath11k
will add more confusion with the patch numbering.
Since the support of ath11k based device is imminent, prepare the mac80211
ath patch dir and split it in the dedicated ath5k, ath9k, ath10k and ath11k
(empty for now).
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Felix Fietkau [Thu, 3 Jun 2021 13:21:00 +0000 (15:21 +0200)]
hostapd: fix bringing up vlan interfaces with the no-bridge option
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Fri, 4 Jun 2021 07:11:37 +0000 (09:11 +0200)]
netifd: update to the latest version
61a71e5e49c3 bridge: dynamically create vlans for hotplug members
cb6ee9608e10 bridge: fix dynamic delete of hotplug vlans
7f199050f395 wireless: pass the real network ifname to the setup script
50381d0a2998 bridge: allow adding/removing VLANs to configured member ports via hotplug
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Hans Dedecker [Thu, 3 Jun 2021 19:04:16 +0000 (21:04 +0200)]
odhcpd: update to git HEAD
a12fcb3 config: log config parse failures to syslog
ebd4297 cmake: enforce additonal compiler checks
405da32 odhcpd: fix extra compiler warning
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
John Crispin [Thu, 3 Jun 2021 13:57:07 +0000 (15:57 +0200)]
hostapd: fix radius problem due to invalid attributes
The offending commit caused the configuration file to contain:
radius_auth_req_attr=
radius_acct_req_attr=
which cause hostapd to add an ATTR of type 0 into the messages.
hostapd: RADIUS message: code=4 (Accounting-Request) identifier=0 length=93
hostapd: Attribute 40 (Acct-Status-Type) length=6
hostapd: Value: 7
hostapd: Attribute 30 (Called-Station-Id) length=28
hostapd: Value: 'C4-41-1E-F5-2D-55:OpenWifi'
hostapd: Attribute 61 (NAS-Port-Type) length=6
hostapd: Value: 19
hostapd: Attribute 0 (?Unknown?) length=3 <----------------
hostapd: Attribute 55 (Event-Timestamp) length=6
hostapd: Value:
1622726457
hostapd: Attribute 41 (Acct-Delay-Time) length=6
hostapd: Value: 0
hostapd: Attribute 44 (Acct-Session-Id) length=18
hostapd: Value: '
9B5961E7235AAEC6'
Fixes: 3bd6c8c728e (hostapd: add additional radius options)
Signed-off-by: John Crispin <john@phrozen.org>
Petr Štetiar [Thu, 3 Jun 2021 07:49:58 +0000 (09:49 +0200)]
ubus: update to version 2021-06-03
This update contains following changes:
* ubusd: protect against too-short messages
* ubusd: add per-client tx queue limit
* ubusd: convert tx_queue to linked list
Fixes: FS#1525
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Felix Fietkau [Thu, 3 Jun 2021 03:38:53 +0000 (05:38 +0200)]
mac80211: fix typo
Remove stray parenthesis
Signed-off-by: Felix Fietkau <nbd@nbd.name>
David Bauer [Wed, 2 Jun 2021 21:46:06 +0000 (23:46 +0200)]
kernel: ar8216: remove soft_reset
ar8xxx_soft_reset is effectively a NOP function. In the PHY state
machine, the availability and result of a soft_reset function
makes no difference for the code flow.
Thus, we can safely remove this method.
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Wed, 2 Jun 2021 17:34:01 +0000 (19:34 +0200)]
kernel: ar8216: add get_features method
Modifying PHY capabilities in the probe function broke with upstream
commit
92ed2eb7f4b7 ("net: phy: probe the PHY before determining the
supported features").
AR8316 switches only support 10/100 Mbit/s link modes because of this
change.
Provide a get_features method for the PHY driver, so Gigabit link mode
will be advertised to link partners again.
Signed-off-by: David Bauer <mail@david-bauer.net>
Paul Spooren [Wed, 2 Jun 2021 20:09:58 +0000 (10:09 -1000)]
build/json: fix DEVICE_PACKAGES
The variable was missing in the definition of DEFAULT_DEVICE_VARS which
caused it to contain wrong values, messing up the resulting JSON files.
This patch adds the variable DEVICE_PACKAGES to DEFAULT_DEVICE_VARS.
Suggested-by: Baptiste Jonglez <git@bitsofnetworks.org>
Signed-off-by: Paul Spooren <mail@aparcar.org>
Felix Fietkau [Wed, 2 Jun 2021 06:49:19 +0000 (08:49 +0200)]
mt76: update to the latest version
bddc1db76d0f mt76: mt7915: drop the use of repeater entries for station interfaces
3c90f35dddac mt76: mt7915: add thermal sensor device support
afab0e8202ff mt76: mt7915: add thermal cooling device support
41cf02184699 mt76: mt7615: add thermal sensor device support
2ac6b8762565 mt76: connac: update BA win size in Rx direction
ddb301127291 mt76: mt7921: fix reset under the deep sleep is enabled
e4cbefd1d69a mt76: mt7921: avoid unnecessary consecutive WiFi resets
393eea2034d7 mt76: mt7921: fix invalid register access in wake_work
a15d46407ffa mt76: mt7921: fix OMAC idx usage
e4d267d8e900 mt76: mt7921: enable runtime pm by default
50fd8ce2412a mt76: connac: add bss color support for sta mode
e29058c3c860 mt76: mt7921: return proper error value in mt7921_mac_init
c89c8c347b1e mt76: mt7921: do not schedule hw reset if the device is not running
9f7bb428e587 mt76: mt7921: reset wfsys during hw probe
22ea365913b5 mt76: mt7915: add .offset_tsf callback
ad91f8e8e494 mt76: mt7615: add .offset_tsf callback
6f871f35e3c1 mt76: mt7915: use mt7915_mcu_get_txpower_sku() to get per-rate txpower
597b68b7daa3 mt76: mt7615: remove useless if condition in mt7615_add_interface()
3945264468eb mt76: testmode: fix memory leak in mt76_testmode_alloc_skb
bdcc57a11606 mt76: testmode: remove unnecessary function calls in mt76_testmode_free_skb
a9763452601d mt76: testmode: remove undefined behaviour in mt76_testmode_alloc_skb
4aef2a2be464 mt76: mt7615: fix potential overflow on large shift
d9dd7635b055 mt76: mt7915: use mt7915_mcu_get_mib_info() to get survey data
d740e921758a mt76: mt7921: introduce mac tx done handling
259ddfc7cb73 mt76: mt7921: update statistic in active mode only
757b93f4b179 mt76: mt7921: remove leftover 80+80 HE capability
1fcff599b2e1 mt76: allow hw driver code to overwrite wiphy interface_modes
c55c22e39b7d mt7915: update firmware to
2020110522
10548aef1f45 mt76: mt7915: improve error recovery reliability
ed6b0c79820c mt76: mt7921: set MT76_RESET during mac reset
321443258bea mt76: move mt76_rates in mt76 module
d1652e8af9e1 Revert "mt76: connac: do not schedule wake_work if the runtime-pm is disabled"
4f4cab39ed9f mt76: mt7915: read all eeprom fields from fw in efuse mode
71450535f164 mt76: mt7921: enable hw offloading for wep keys
833d577e430c mt76: mt7921: remove mt7921_get_wtbl_info routine
67b7a22d2b99 mt76: mt7921: enable random mac address during sched_scan
cf1ff7bf4f1b mt76: mt7915: setup drr group for peers
ef2f7aa8745f mt76: mt7615: update radar parameters
b9f09f530223 mt76: mt7915: fix MT_EE_CAL_GROUP_SIZE
Signed-off-by: Felix Fietkau <nbd@nbd.name>
John Crispin [Tue, 6 Apr 2021 12:59:41 +0000 (14:59 +0200)]
hostapd: add eap_server support
This makes it possible to avoid using a RADIUS server for WPA enterprise authentication
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Thu, 27 May 2021 11:15:40 +0000 (13:15 +0200)]
hostapd: add default values for r0kh/r1kh
This allows WPA enterprise roaming in the same mobility domain without any
manual key configuration (aside from radius credentials)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Wed, 26 May 2021 12:34:46 +0000 (14:34 +0200)]
hostapd: add support for specifying the maxassoc parameter as a device option
It allows enforcing a limit on associated stations to be enforced for the
full device, e.g. in order to deal with hardware/driver limitations
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Wed, 26 May 2021 11:50:43 +0000 (13:50 +0200)]
hostapd: add support for configuring proxy ARP
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Wed, 26 May 2021 11:34:41 +0000 (13:34 +0200)]
hostapd: add configurable rssi thresholds for rejecting assoc/probe requests
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Wed, 26 May 2021 11:04:50 +0000 (13:04 +0200)]
hostapd: add support for configuring the beacon rate
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Wed, 2 Jun 2021 05:45:31 +0000 (07:45 +0200)]
mac80211: do not enable VHT in the default config on 2.4 GHz
Some drivers advertise it, but it's not supported at the moment
Reported-by: John Thomson <git@johnthomson.fastmail.com.au>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Wed, 2 Jun 2021 05:42:40 +0000 (07:42 +0200)]
mac80211: fix detecting VHT capabilities when generating the default config
The colon does not directly follow the "VHT Capabilities" string
Reported-by: John Thomson <git@johnthomson.fastmail.com.au>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Tue, 1 Jun 2021 21:19:48 +0000 (23:19 +0200)]
kernel: backport fix for hang on napi_disable with threaded NAPI
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Hans Dedecker [Sun, 30 May 2021 17:38:45 +0000 (19:38 +0200)]
glibc: update to latest 2.33 HEAD (BZ #27892)
0ef0e6de7f powerpc: Fix handling of scv return error codes [BZ #27892]
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Adrian Schmutzler [Sat, 29 May 2021 19:24:50 +0000 (21:24 +0200)]
layerscape: refresh kernel config
Run `make kernel_oldconfig CONFIG_TARGET=subtarget`
This mostly aims at getting rid of redundant/unneeded symbols.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Yangbo Lu [Mon, 19 Oct 2020 05:21:07 +0000 (13:21 +0800)]
kernel: add missing symbol CONFIG_AHCI_XGENE
Add missing symbol CONFIG_AHCI_XGENE.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[also add for 5.10, remove from layerscape target config]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
John Audia [Fri, 28 May 2021 14:59:12 +0000 (10:59 -0400)]
kernel: bump 5.4 to 5.4.123
All patches automatically rebased.
Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
projects / openwrt / staging / lynxis.git / log