sfc: Update MCDI protocol definitions

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/amd8111e.c: Fix continuation line formats

String constants that are continued on subsequent lines with \
are not good.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

can: add support for CAN interface cards based on the PLX90xx PCI bridge

This driver is for CAN interface cards based on the PLX90xx PCI bridge.
Driver supports now:
 - Adlink PCI-7841/cPCI-7841 card (http://www.adlinktech.com/)
 - Adlink PCI-7841/cPCI-7841 SE card
 - Marathon CAN-bus-PCI card (http://www.marathon.ru/)
 - TEWS TECHNOLOGIES TPMC810 card (http://www.tews.com/)

Changes since v1:
 - Added some defines for static inline int plx_pci_check_sja1000(...)
 - static struct pci_device_id plx_pci_tbl[] replaced by
   static DEFINE_PCI_DEVICE_TABLE(plx_pci_tbl)
 - Typo fixed

Signed-off-by: Pavel Cheblakov <P.B.Cheblakov@inp.nsk.su>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cxgb3: add memory barriers

Add memory barriers to fix crashes observed on newest PowerPC platforms.
The HW and driver state of the receive rings were getting out of sync.

Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MCS7830 USB-Ether: resume _with_ working link, via .reset_resume support

ChangeLog:
Implement .reset_resume support to retain a live network connection
during suspend despite USB power loss.
- rework operation to reference cached data in mcs7830_data and
  netdev->dev_addr
- update netdev->dev_addr only in case new MAC was set successfully
. Tests done:
  . ethtool -d pre-/post-suspend: register values match
  . running ssh session suspend, resume: works
  . ifdown device, suspend, resume: works
  . ifup, suspend, unplug, resume: WORKS (eth1 is removed, re-ifup of eth1
    after card replug works)
  . verified identical MAC in ifconfig post-resume
    (ok, should be verified on network side to be fully certain...)

Keywords: suspend resume network connection dead interface down

Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

MCS7830 USB-Ether: change register define

ChangeLog:
- rename register, add comment

Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

MCS7830 USB-Ether: Spelling corrections

ChangeLog:
- spelling corrections / whitespace

Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

MCS7830 USB-Ether: add Rx error support

ChangeLog:
- evaluate Rx error statistics from trailing Rx status byte
- add driver TODO list
- add myself to authors

Quilt series run-tested, based on 2.6.33-rc4 (net-2.6.git mcs7830 has idle history,
should be good to go).

Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: add loopback diagnostic test

Loopback test (offline) added in ethtool self test.
o Set device in loopback mode
o Send packets
o Process receive packets in qlcnic_process_rcv_ring_diag()
o Compare packets
o Reset device in normal mode.

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: add interrupt diagnostic test

Interrupt test (offline) added in ethtool self test.
Register a temporary interrupt handler and then send command to fw
to raise an interrupt.

Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: support LED blink for device identification

Added support of device identification by blinking LED for specified time.

Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: protect resoruce cleanup by rtnl lock

o context resources can be in used, while resoruce cleanup is in progress,
  during fw recover.
o Null pointer execption can occur in send_cmd_desc, if fw recovery
  module frees tx ring without rtnl lock.
o Same applies to ethtool register dump and FW health registers should be dump
  in any case.

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: clear device reset state after fw recovery

o After firmware recovery, clear device reset state transition register.
  Otherwise firmware reload can occur unnecessary.

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: add ethernet identifier in board info

Added missing identifier that distinguishes between
FCOE/ISCSI/ETHERNET functions.

Signed-off-by: Rajesh K Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic: use DEFINE_PCI_DEVICE_TABLE

Use DEFINE_PCI_DEVICE_TABLE() so we get place PCI ids table into
correct section in every case.

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sky2: Fix TX_MAP_PAGE misspelling

Btw of the dma-debug problem reported by Michael Breuer I spotted
a tiny misspelling in TX_MAP_PAGE definition introduced by commit
6b84dacadbdc3.

Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

virtio_net: Defer skb allocation in receive path Date: Wed, 13 Jan 2010 12:53:38 -0800

virtio_net receives packets from its pre-allocated vring buffers, then it
delivers these packets to upper layer protocols as skb buffs. So it's not
necessary to pre-allocate skb for each mergable buffer, then frees extra
skbs when buffers are merged into a large packet. This patch has deferred
skb allocation in receiving packets for both big packets and mergeable buffers
to reduce skb pre-allocations and skb frees. It frees unused buffers by calling
detach_unused_buf in vring, so recv skb queue is not needed.

Signed-off-by: Shirley Ma <xma@us.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

virtio: Add ability to detach unused buffers from vrings

There's currently no way for a virtio driver to ask for unused
buffers, so it has to keep a list itself to reclaim them at shutdown.
This is redundant, since virtio_ring stores that information.  So
add a new hook to do this.

Signed-off-by: Shirley Ma <xma@us.ibm.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

xfrm: avoid spinlock in get_acqseq()

Use atomic_inc_return() in get_acqseq() to avoid taking a spinlock

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv4: ip_fragment: fix unbalanced rcu_read_unlock()

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/irda: sh_sir: Add SuperH IrDA driver

This is very simple IrDA SIR driver for SuperH.
This driver was tested by irdaping/ircp on SH7724 EcoVec24 board

Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

igmp: fix ip_mc_sf_allow race [v5]

Almost all igmp functions accessing inet->mc_list are protected by
rtnl_lock(), but there is one exception which is ip_mc_sf_allow(),
so there is a chance of either ip_mc_drop_socket or ip_mc_leave_group
remove an entry while ip_mc_sf_allow is running causing a crash.

Signed-off-by: Flavio Leitner <fleitner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

can: deny filterlist access on non-CAN interfaces

In commit 20dd3850bcf860561496827b711fa10fecf6e787 "can: Speed up CAN frame
receiption by using ml_priv" the formerly used hlist of receiver lists for
each CAN netdevice has been replaced.

The hlist content ensured only CAN netdevices to be accessed by the
can_rx_(un)register() functions which accidently dropped away together with
the hlist receiver implementation.

This patch re-introduces the check for CAN netdevices in can_rx_(un)register().

Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

tulip/xircom_cb.c: Use dev_<level> and pr_<level>

Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Remove DRV_NAME and xircom_cb from pr_<level>
Convert embedded function names in logging messages to %s, __func__

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tulip/winbond-840.c: Use dev_<level> and pr_<level>

Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx
Convert %d.%d.%d.%d to %pI4

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tulip/uli526x.c: Use dev_<level> and pr_<level>

Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Remove DRV_NAME from logging messages
Add do {} while(0) to ULI526X_DBUG macro
Make SHOW_MEDIA_TYPE macro more readable

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tulip/timer.c: Use dev_<level> and pr_<level>

Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tulip/pnic2.c: Use dev_<level> and pr_<level>

Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tulip/pnic.c: Use dev_<level> and pr_<level>

Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tulip/media.c: Use dev_<level> and pr_<level>

Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tulip/interrupt.c: Use dev_<level> and pr_<level>

Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tulip/eeprom.c: Use dev_<level> and pr_<level>

Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tulip/dmfe.c: Use dev_<level> and pr_<level>

Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Remove 'DRV_NAME ": ' from logging messages
Convert commented out printks to pr_debug

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tulip/de2104x.c: Use dev_<level> and pr_<level>

Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tulip/21142.c: Use dev_<level> and pr_<level>

Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tulip_core: Use dev_<level> and pr_<level>

Convert printks to dev_<level> where appropriate
Convert printks to pr_<level>
Change print formats with %d.dx to %0dx
Coalesce long formats

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sched: add head drop fifo queue

This adds an additional queuing strategy, called pfifo_head_drop,
to remove the oldest skb in the case of an overflow within the queue -
the head element - instead of the last skb (tail). To remove the oldest
skb in congested situations is useful for sensor network environments
where newer packets reflect the superior information.

Reviewed-by: Florian Westphal <fw@strlen.de>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

netns xfrm: ipcomp6 support

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netns xfrm: ipcomp support

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netns xfrm: xfrm6_tunnel in netns

I'm not sure about rcu stuff near kmem cache destruction:
* checks for non-empty hashes look bogus, they're done _before_
  rcu_berrier()
* unregistering netns ops is done before kmem_cache destoy
  (as it should), and unregistering involves rcu barriers by itself

So it looks nothing should be done.

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netns xfrm: fixup xfrm6_tunnel error propagation

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: merge fixup for qlge_main

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of /linux/kernel/git/davem/net-2.6

netdev: remove HAVE_ leftovers

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bonding: bond_open error return value

The convention for API functions in kernel is to return errno value;
bond_open would return -1 if alb setup failed. The only reason that
could happen is if kmalloc() failed.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: if ixgbe_copy_dcb_cfg is going to fail learn about it early

Call ixgbe_copy_dcb_cfg() earlier in the ixgbe_dcbnl_set_all() so that
we can learn if this is going to fail as early as possible.  Previously,
ixgbe_down or ixgbe_close were being called before this check and the
IXGBE_RESETTING bit was being set and cleared.  Worse if this failed
the corresponding ixgbe_up/ndo_open would not called.

Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: set the correct DCB bit for pg tx settings

Set the correct bit BIT_PG_TX when tx PG settings are set.

Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

igbvf: fix issue w/ mapped_as_page being left set after unmap

This change fixes an issue in igbvf with mapped_as_page being left set
after a page is unmapped which results in buffers which are mapped via map
single being unmapped as page.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net: ks8851_mll ethernet network driver

Hello David Miller,

I fix a bug in ks8851_mll driver, which has existed since 2.6.32-rc6.

>From : David J. Choi <david.choi@micrel.com>

Fix a bug that the data pointers in the interrupt handler are set wrong, which is related with the 5th parameter of request_irq().

Signed-off-by : David J. Choi <david.choi@micrel.com>

Signed-off-by: David S. Miller <davem@davemloft.net>

be2net: Bug fix to support newer generation of BE ASIC

Bug fix in be2net for newer generation of BladeEngine ASIC.

Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6

net/atm: Cleanup dprint/ddprintk #defines and uses

Move "mpoa:%s: ", __func__/__FILE__ to #defines
Remove mpoa __func__/__FILE__ from dprintk uses
Add and use #define dprint_cont where appropriate

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/atm/lec.c: Add __lec_arp_check_expire and other cleanups

Reduce indentation in lec_arp_check_expire
Indent a case label
Remove != NULL logical tests from while ((skb = foo())) assign and tests

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/atm/svc.c: checkpatch cleanups

Convert #include <asm... to #include <linux...
Spacing cleanups
Mostly 80 column wrapped
Move trailing statements to new lines
switch/case cleanups

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/atm/signaling.c: checkpatch cleanups

Mostly 80 column wrapped.
Move embedded assigns out of tests
Move trailing statements to new lines
switch/case cleanups

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/atm/resources.c: checkpatch cleanups

Spacing cleanups
Mostly 80 column wrapped.
Move embedded assigns out of tests
Move trailing statements to new lines
switch/case cleanups

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/atm/raw.c: checkpatch cleanups

Spacing cleanups
Mostly 80 column wrapped.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/atm/pvc.c: checkpatch cleanups

Spacing cleanups
Mostly 80 column wrapped.
Move trailing statements to new lines

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/atm/proc.c: checkpatch cleanups

Convert #include <asm... to #include <linux...
Mostly 80 column wrapped.
Spacing cleanups
Move trailing statements to new lines
switch/case cleanups

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/atm/pppoatm.c: checkpatch cleanups

Move embedded assigns out of tests
Move trailing statements to new lines
Move labels to column 1

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/atm/mpoa_proc.c: checkpatch cleanups

Convert #include <asm... to #include <linux...
Add printk argument verification to dprintk and ddprintk
Spacing cleanups
Mostly 80 column wrapped.
Removed unnecessary breaks after returns
Use %pI4 in seq_printf of IP address

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/atm/mpoa_caches.c: checkpatch cleanups

Convert #include <asm... to #include <linux...
Add printk argument verification to dprintk and ddprintk
Spacing cleanups
Mostly 80 column wrapped.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/atm/mpc.c: checkpatch cleanups

Convert #include <asm... to #include <linux...
Add printk argument verification to dprintk and ddprintk
Spacing cleanups
Mostly 80 column wrapped.
printk->pr_info and pr_cont
Moved labels to column 1
Move trailing statements to new lines
switch/case cleanups
remove unnecessary breaks after returns
Remove unnecessary braces around single line statements

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/atm/lec.c: checkpatch cleanups

Convert #include <asm... to #include <linux...
Mostly 80 column wrapped.
Spacing cleanups
Convert printks to pr_<level>
Use print_hex_dump
Move embedded assigns out of tests
Move trailing statements to new lines
Remove unnecessary braces around single line statements
switch/case cleanups
Removed paren around returns
Use %pM
Moved leading continuation logical tests to end of previous line

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/atm/ioctl.c: checkpatch cleanups

Spacing cleanups
Moved EXPORT_SYMBOL
Mostly 80 column wrapped.
switch/case cleanups

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/atm/common.c: checkpatch cleanups

Convert #include <asm... to #include <linux...
Move EXPORT_SYMBOL
Spacing cleanups
Use __func__ in printks
Indent switch/case statements
Move trailing statements to new line
Hoist assigns from if tests

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/atm/clip.c: checkpatch cleanups

Convert #include <asm... to #include <linux...
Spacing cleanups
Move labels to column 1
Move logical continuation tests to end of previous line

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/atm/br2684.c: checkpatch cleanups

Convert #include <asm... to #include <linux...
Use print_hex_dump
Spacing cleanups
Move logical continuation tests to end of previous line
80 column wrapping
Move goto branch label to column 1
Remove unnecessary single statement braces

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/atm/atm_sysfs.c: checkpatch cleanups

Add space after for
Indent switch/case statements
80 column wrapping

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/atm/atm_misc.c: checkpatch cleanups

Moved EXPORT_SYMBOL to follow definition
Add space after commas

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/atm/addr.c: Convert include <asm to include <linux

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/atm: Convert printk to pr_<level>

Add #define pr_fmt(fmt) KBUILD_MODNAME ":%s: " fmt, __func__
Remove function names from output
Use single line pr_debug instead of broken multiple uses without newline

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

starfire: clean up properly if firmware loading fails

netdev_open() will return without cleaning up net device or hardware state
if firmware loading fails.  This results in a BUG() on a second attempt to
bring the interface up, reported in
<http://bugzilla.kernel.org/show_bug.cgi?id=15091>, and probably has even
worse effects if the driver is removed afterwards.

Call netdev_close() to clean up on failure.

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=15091

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Reported-by: Michael Moffatt <michael@moffatt.org.nz>
Tested-by: Michael Moffatt <michael@moffatt.org.nz>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

mac80211: fix NULL pointer dereference when ftrace is enabled

I got below kernel oops when I try to bring down the network interface if
ftrace is enabled. The root cause is drv_ampdu_action() is passed with a
NULL ssn pointer in the BA session tear down case. We need to check and
avoid dereferencing it in trace entry assignment.

BUG: unable to handle kernel NULL pointer dereference
Modules linked in: at (null)
IP: [<f98fe02a>] ftrace_raw_event_drv_ampdu_action+0x10a/0x160 [mac80211]
*pde = 00000000
Oops: 0000 [#1] SMP DEBUG_PAGEALLOC
[...]
Call Trace:
 [<f98fdf20>] ? ftrace_raw_event_drv_ampdu_action+0x0/0x160 [mac80211]
 [<f98dac4c>] ? __ieee80211_stop_rx_ba_session+0xfc/0x220 [mac80211]
 [<f98d97fb>] ? ieee80211_sta_tear_down_BA_sessions+0x3b/0x50 [mac80211]
 [<f98dc6f6>] ? ieee80211_set_disassoc+0xe6/0x230 [mac80211]
 [<f98dc6ac>] ? ieee80211_set_disassoc+0x9c/0x230 [mac80211]
 [<f98dcbb8>] ? ieee80211_mgd_deauth+0x158/0x170 [mac80211]
 [<f98e4bdb>] ? ieee80211_deauth+0x1b/0x20 [mac80211]
 [<f8987f49>] ? __cfg80211_mlme_deauth+0xe9/0x120 [cfg80211]
 [<f898b870>] ? __cfg80211_disconnect+0x170/0x1d0 [cfg80211]

Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ariadne: Fix build.

References removed HAVE_MULTICAST.

Reporeted-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: conntrack: Add member of user to nf_ct_frag6_queue structure

The commit 0b5ccb2(title:ipv6: reassembly: use seperate reassembly queues for
conntrack and local delivery) has broken the saddr&&daddr member of
nf_ct_frag6_queue when creating new queue.  And then hash value
generated by nf_hashfn() was not equal with that generated by fq_find().
So, a new received fragment can't be inserted to right queue.

The patch fixes the bug with adding member of user to nf_ct_frag6_queue structure.

Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

virtio_net: Make delayed refill more reliable

I have seen RX stalls on a machine that experienced a suspected
OOM.  After the stall, the RX buffer is empty on the guest side
and there are exactly 16 entries available on the host side.  As
the number of entries is less than that required by a maximal
skb, the host cannot proceed.

The guest did not have a refill job scheduled.

My diagnosis is that an OOM had occured, with the delayed refill
job scheduled.  The job was able to allocate at least one skb, but
not enough to overcome the minimum required by the host to proceed.

As the refill job would only reschedule itself if it failed completely
to allocate any skbs, this would lead to an RX stall.

The following patch removes this stall possibility by always
rescheduling the refill job until the ring is totally refilled.

Testing has shown that the RX stall no longer occurs whereas
previously it would occur within a day.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: Use fixed-size buffers for MCDI NVRAM requests

The low-level MCDI code always uses 32-bit MMIO operations, and
callers must pad input and output buffers to multiples of 4 bytes.
The MCDI NVRAM functions are not doing this.  Also, their buffers are
declared as variable-length arrays with no explicit maximum length.

Switch to a fixed buffer size based on the chunk size used by the
MTD driver (which is a multiple of 4).

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: Add workspace for GMAC bug workaround to MCDI MAC_STATS buffer

Due to a hardware bug in the SFC9000 family, the firmware must
transfer raw GMAC statistics to host memory before aggregating them
into the cooked (speed-independent) MAC statistics.  Extend the stats
buffer to support this.

The length of the buffer is explicit in the MAC_STATS command, so this
change is backward-compatible on both sides.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp_probe: avoid modulus operation and wrap fix

By rounding up the buffer size to power of 2, several expensive
modulus operations can be avoided.  This patch also solves a bug where
the gap need when ring gets full was not being accounted for.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlge: Only free resources if they were allocated

Currently qlge tries to release regions even if they were not allocated.
This causes messages like the following in the kernel log

Trying to free nonexistent resource <00000000006af400-00000000006af4ff>
Trying to free nonexistent resource <00003c04ff9f4000-00003c04ff9f7fff>
Trying to free nonexistent resource <00003c04ffc00000-00003c04ffcfffff>

This patch fixes the goto logic in order to not release the resources
if they were not allocated.

Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: use helpers to access uc list V2

This patch introduces three macros to work with uc list from net drivers.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ath9k: fix eeprom INI values override for 2GHz-only cards

Among other changes, this commit:

   commit 06d0f0663e11cab4ec5f2c143a118d71a12fbbe9
   Author: Sujith <Sujith.Manoharan@atheros.com>
   Date:   Thu Feb 12 10:06:45 2009 +0530

   ath9k: Enable Fractional N mode

changed the hw attach code to fix up initialization values only for
dual band devices, however the commit message did not give a reason as
to why this would be useful or necessary.

According to tests by Jorge Boncompte, this breaks at least some
2GHz-only cards, so the code should be changed back to the
unconditional INI fixup.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Jorge Boncompte <jorge@dti2.net>
Cc: stable@kernel.org
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: fix pointer signedness warning

There are a few station addresses that are
char *, instead of the normal u8 *; gcc
gives pointer signedness warnings for some
of those, so use u8 * consistently.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

netns xfrm: deal with dst entries in netns

GC is non-existent in netns, so after you hit GC threshold, no new
dst entries will be created until someone triggers cleanup in init_net.

Make xfrm4_dst_ops and xfrm6_dst_ops per-netns.
This is not done in a generic way, because it woule waste
(AF_MAX - 2) * sizeof(struct dst_ops) bytes per-netns.

Reorder GC threshold initialization so it'd be done before registering
XFRM policies.

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sky2: revert config space change

Obviously, this register had some other impact that is causing
the regression.  Either it is masking some other access or needs
to be reset in some path.

Either, way it is best to just revert the change for 2.6.33

This reverts commit 166a0fd4c788ec7f10ca8194ec6d526afa12db75.

Signed-off-by: David S. Miller <davem@davemloft.net>

vlan: fix vlan_skb_recv()

Bruno Prémont found commit 9793241fe92f7d930
(vlan: Precise RX stats accounting) added a regression for non
hw accelerated vlans.

[   26.390576] BUG: unable to handle kernel NULL pointer dereference at (null)
[   26.396369] IP: [<df856b89>] vlan_skb_recv+0x89/0x280 [8021q]

vlan_dev_info() was used with original device, instead of
skb->dev. Also spotted by Américo Wang.

Reported-By: Bruno Prémont <bonbons@linux-vserver.org>
Tested-By: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netns xfrm: fix "ip xfrm state|policy count" misreport

"ip xfrm state|policy count" report SA/SP count from init_net,
not from netns of caller process.

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

sky2: Enable/disable WOL per hardware device

Y2_HW_WOL_ON/Y2_HW_WOL_OFF should be set and cleared per chip,
not per port.  On dual port cards, Y2_HW_WOL_ON should be
enabled if either sky2 port has WOL enabled.

Found while reviewing code for a WOL regression, though this is
probably not the cause of the regression.

Signed-off-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbevf: Fix IPv6 GSO type checks

Based on patch from Sridhar Samudrala

The following patch fixes the check for IPv6 GSO packet in ixgbevf
driver to use skb_is_gso_v6(). SKB_GSO_DODGY is also set
when packets are forwarded from a guest.

CC: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Fix IPv6 GSO type checks in Intel ethernet drivers

Found this problem when testing IPv6 from a KVM guest to a remote
host via e1000e device on the host.
The following patch fixes the check for IPv6 GSO packet in Intel
ethernet drivers to use skb_is_gso_v6(). SKB_GSO_DODGY is also set
when packets are forwarded from a guest.

Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

IP: Send an ICMP "Fragment Reassembly Timeout" message when enabling connection track

No matter whether connection track is enabled, an end host should send
an ICMPv4 "Fragment Reassembly Timeout" message when defrag timeout.
The reasons are following two points:

1. RFC 792 says:
   >>>> >> > >   If a host reassembling a fragmented datagram cannot complete the
   >>>> >> > >   reassembly due to missing fragments within its time limit it
   >>>> >> > >   discards the datagram, and it may send a time exceeded message.
   >>>> >> > >
   >>>> >> > >   If fragment zero is not available then no time exceeded need be
   >>>> >> > >   sent at all.
   >>>> >> > >
   >>>> >> > > Read more: http://www.faqs.org/rfcs/rfc792.html#ixzz0aOXRD7Wp

2. Patrick McHardy also agrees with this opinion.   :-)
   About the discussion of this opinion, refer to http://patchwork.ozlabs.org/patch/41649

The patch fixed the problem like this:
When enabling connection track, fragments are received at PRE_ROUTING HOOK.
If they are failed to reassemble, ip_expire() will be called.
Before sending an ICMP "Fragment Reassembly Timeout" message,
the patch searches router table to get the destination entry only for host type.

The patch has been tested on both host type and route type.

Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

igb/igbvf: cleanup exception handling in tx_map_adv

After removing the skb_dma_map/unmap calls the exception handling in
igb_tx_map_adv is not correct.  The issue is that the count value was not
being correctly handled so as a result we were not rewinding the ring as
back as we should have been.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

icmp: move icmp_err_convert[] to .rodata

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: constify MIB name tables

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

neigh: simplify seq_file code

Simpily pass 'struct neigh_table' with seq_file private pointer,
and save one dereference. Proc entry itself isn't interesting.

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netdev: remove certain HAVE_ macros

After netdev_ops compat code HAVE_* macros aren't needed, in fact
they _will_ result in compile breakage for out of tree drivers.

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MAINTAINERS: Add Intel igbvf maintainer

Add igbvf to the list of supported Intel drivers and Alex to the list of
maintainers.

Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbevf: Tell network stack to stop tx when the VF detects PF reset

When the VF detects that the PF has reset turn off carrier and stop all
tx queues.

Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbevf: Fix panics in the VF driver

Fix panics in the VF driver that occur when you bring it down after
having already brought the PF down.

Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>